ARM: dts: qcom: ipq8064: reorganize node order and sort them
Subsystems (2)
PATCH 1/2 ARM: dts: qcom: ipq8064: reorganize node order and sort them
Reorganize node order and sort them by address.
---
This was picked from for-next qcom branch [1]. Reorganize dtsi as requested.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux.git/?h=for-next
arch/arm/boot/dts/qcom-ipq8064.dtsi | 766 ++++++++++++++-------------- 1 file changed, 383 insertions(+), 383 deletions(-)
arch/arm/boot/dts/qcom-ipq8064.dtsi +383 -383
@@ -332,19 +332,59 @@ soc: soc { ranges; compatible = "simple-bus"; - lpass@28100000 { - compatible = "qcom,lpass-cpu"; - status = "disabled"; - clocks = <&lcc AHBIX_CLK>, - <&lcc MI2S_OSR_CLK>, - <&lcc MI2S_BIT_CLK>; - clock-names = "ahbix-clk", - "mi2s-osr-clk", - "mi2s-bit-clk"; - interrupts = <GIC_SPI 85 IRQ_TYPE_EDGE_RISING>; - interrupt-names = "lpass-irq-lpaif"; - reg = <0x28100000 0x10000>; - reg-names = "lpass-lpaif"; + stmmac_axi_setup: stmmac-axi-config { + snps,wr_osr_lmt = <7>; + snps,rd_osr_lmt = <7>; + snps,blen = <16 0 0 0 0 0 0>; + }; + + vsdcc_fixed: vsdcc-regulator { + compatible = "regulator-fixed"; + regulator-name = "SDCC Power"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + rpm: rpm@108000 { + compatible = "qcom,rpm-ipq8064"; + reg = <0x108000 0x1000>; + qcom,ipc = <&l2cc 0x8 2>; + + interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "ack", "err", "wakeup"; + + clocks = <&gcc RPM_MSG_RAM_H_CLK>; + clock-names = "ram"; + + rpmcc: clock-controller { + compatible = "qcom,rpmcc-ipq806x", "qcom,rpmcc"; + #clock-cells = <1>; + }; + }; + + qcom,ssbi@500000 { + compatible = "qcom,ssbi"; + reg = <0x00500000 0x1000>; + qcom,controller-type = "pmic-arbiter"; + }; + + qfprom: qfprom@700000 { + compatible = "qcom,ipq8064-qfprom", "qcom,qfprom"; + reg = <0x00700000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + speedbin_efuse: speedbin@c0 { + reg = <0xc0 0x4>; + }; + tsens_calib: calib@400 { + reg = <0x400 0xb>; + }; + tsens_calib_backup: calib_backup@410 { + reg = <0x410 0xb>; + }; }; qcom_pinmux: pinmux@800000 {
@@ -471,6 +511,35 @@ mux { }; }; + gcc: clock-controller@900000 { + compatible = "qcom,gcc-ipq8064", "syscon"; + clocks = <&pxo_board>, <&cxo_board>; + clock-names = "pxo", "cxo"; + reg = <0x00900000 0x4000>; + #clock-cells = <1>; + #reset-cells = <1>; + #power-domain-cells = <1>; + + tsens: thermal-sensor@900000 { + compatible = "qcom,ipq8064-tsens"; + + nvmem-cells = <&tsens_calib>, <&tsens_calib_backup>; + nvmem-cell-names = "calib", "calib_backup"; + interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "uplow"; + + #qcom,sensors = <11>; + #thermal-sensor-cells = <1>; + }; + }; + + sfpb_mutex: hwlock@1200600 { + compatible = "qcom,sfpb-mutex"; + reg = <0x01200600 0x100>; + + #hwlock-cells = <1>; + }; + intc: interrupt-controller@2000000 { compatible = "qcom,msm-qgic2"; interrupt-controller;
@@ -500,46 +569,198 @@ IRQ_TYPE_EDGE_RISING)>, cpu-offset = <0x80000>; }; + l2cc: clock-controller@2011000 { + compatible = "qcom,kpss-gcc", "syscon"; + reg = <0x2011000 0x1000>; + clocks = <&gcc PLL8_VOTE>, <&pxo_board>; + clock-names = "pll8_vote", "pxo"; + clock-output-names = "acpu_l2_aux"; + }; + acc0: clock-controller@2088000 { compatible = "qcom,kpss-acc-v1"; reg = <0x02088000 0x1000>, <0x02008000 0x1000>; }; + saw0: regulator@2089000 { + compatible = "qcom,saw2"; + reg = <0x02089000 0x1000>, <0x02009000 0x1000>; + regulator; + }; + acc1: clock-controller@2098000 { compatible = "qcom,kpss-acc-v1"; reg = <0x02098000 0x1000>, <0x02008000 0x1000>; }; - adm_dma: dma-controller@18300000 { - compatible = "qcom,adm"; - reg = <0x18300000 0x100000>; - interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>; - #dma-cells = <1>; + saw1: regulator@2099000 { + compatible = "qcom,saw2"; + reg = <0x02099000 0x1000>, <0x02009000 0x1000>; + regulator; + }; - clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>; - clock-names = "core", "iface"; + nss_common: syscon@03000000 { + compatible = "syscon"; + reg = <0x03000000 0x0000FFFF>; + }; - resets = <&gcc ADM0_RESET>, - <&gcc ADM0_PBUS_RESET>, - <&gcc ADM0_C0_RESET>, - <&gcc ADM0_C1_RESET>, - <&gcc ADM0_C2_RESET>; - reset-names = "clk", "pbus", "c0", "c1", "c2"; - qcom,ee = <0>; + usb3_0: usb3@100f8800 { + compatible = "qcom,ipq8064-dwc3", "qcom,dwc3"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x100f8800 0x8000>; + clocks = <&gcc USB30_0_MASTER_CLK>; + clock-names = "core"; + + ranges; + + resets = <&gcc USB30_0_MASTER_RESET>; + reset-names = "master"; status = "disabled"; + + dwc3_0: dwc3@10000000 { + compatible = "snps,dwc3"; + reg = <0x10000000 0xcd00>; + interrupts = <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>; + phys = <&hs_phy_0>, <&ss_phy_0>; + phy-names = "usb2-phy", "usb3-phy"; + dr_mode = "host"; + snps,dis_u3_susphy_quirk; + }; }; - saw0: regulator@2089000 { - compatible = "qcom,saw2"; - reg = <0x02089000 0x1000>, <0x02009000 0x1000>; - regulator; + hs_phy_0: phy@100f8800 { + compatible = "qcom,ipq806x-usb-phy-hs"; + reg = <0x100f8800 0x30>; + clocks = <&gcc USB30_0_UTMI_CLK>; + clock-names = "ref"; + #phy-cells = <0>; + + status = "disabled"; }; - saw1: regulator@2099000 { - compatible = "qcom,saw2"; - reg = <0x02099000 0x1000>, <0x02009000 0x1000>; - regulator; + ss_phy_0: phy@100f8830 { + compatible = "qcom,ipq806x-usb-phy-ss"; + reg = <0x100f8830 0x30>; + clocks = <&gcc USB30_0_MASTER_CLK>; + clock-names = "ref"; + #phy-cells = <0>; + + status = "disabled"; + }; + + usb3_1: usb3@110f8800 { + compatible = "qcom,ipq8064-dwc3", "qcom,dwc3"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x110f8800 0x8000>; + clocks = <&gcc USB30_1_MASTER_CLK>; + clock-names = "core"; + + ranges; + + resets = <&gcc USB30_1_MASTER_RESET>; + reset-names = "master"; + + status = "disabled"; + + dwc3_1: dwc3@11000000 { + compatible = "snps,dwc3"; + reg = <0x11000000 0xcd00>; + interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; + phys = <&hs_phy_1>, <&ss_phy_1>; + phy-names = "usb2-phy", "usb3-phy"; + dr_mode = "host"; + snps,dis_u3_susphy_quirk; + }; + }; + + hs_phy_1: phy@110f8800 { + compatible = "qcom,ipq806x-usb-phy-hs"; + reg = <0x110f8800 0x30>; + clocks = <&gcc USB30_1_UTMI_CLK>; + clock-names = "ref"; + #phy-cells = <0>; + + status = "disabled"; + }; + + ss_phy_1: phy@110f8830 { + compatible = "qcom,ipq806x-usb-phy-ss"; + reg = <0x110f8830 0x30>; + clocks = <&gcc USB30_1_MASTER_CLK>; + clock-names = "ref"; + #phy-cells = <0>; + + status = "disabled"; + }; + + sdcc3bam: dma-controller@12182000 { + compatible = "qcom,bam-v1.3.0"; + reg = <0x12182000 0x8000>; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc SDC3_H_CLK>; + clock-names = "bam_clk"; + #dma-cells = <1>; + qcom,ee = <0>; + }; + + sdcc1bam: dma-controller@12402000 { + compatible = "qcom,bam-v1.3.0"; + reg = <0x12402000 0x8000>; + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc SDC1_H_CLK>; + clock-names = "bam_clk"; + #dma-cells = <1>; + qcom,ee = <0>; + }; + + amba: amba { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + sdcc3: mmc@12180000 { + compatible = "arm,pl18x", "arm,primecell"; + arm,primecell-periphid = <0x00051180>; + status = "disabled"; + reg = <0x12180000 0x2000>; + interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "cmd_irq"; + clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>; + clock-names = "mclk", "apb_pclk"; + bus-width = <8>; + cap-sd-highspeed; + cap-mmc-highspeed; + max-frequency = <192000000>; + sd-uhs-sdr104; + sd-uhs-ddr50; + vqmmc-supply = <&vsdcc_fixed>; + dmas = <&sdcc3bam 2>, <&sdcc3bam 1>; + dma-names = "tx", "rx"; + }; + + sdcc1: mmc@12400000 { + status = "disabled"; + compatible = "arm,pl18x", "arm,primecell"; + arm,primecell-periphid = <0x00051180>; + reg = <0x12400000 0x2000>; + interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "cmd_irq"; + clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>; + clock-names = "mclk", "apb_pclk"; + bus-width = <8>; + max-frequency = <96000000>; + non-removable; + cap-sd-highspeed; + cap-mmc-highspeed; + mmc-ddr-1_8v; + vmmc-supply = <&vsdcc_fixed>; + dmas = <&sdcc1bam 2>, <&sdcc1bam 1>; + dma-names = "tx", "rx"; + }; }; gsbi1: gsbi@12440000 {
@@ -654,56 +875,6 @@ i2c@16380000 { }; }; - gsbi5: gsbi@1a200000 { - compatible = "qcom,gsbi-v1.0.0"; - cell-index = <5>; - reg = <0x1a200000 0x100>; - clocks = <&gcc GSBI5_H_CLK>; - clock-names = "iface"; - #address-cells = <1>; - #size-cells = <1>; - ranges; - status = "disabled"; - - syscon-tcsr = <&tcsr>; - - gsbi5_serial: serial@1a240000 { - compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; - reg = <0x1a240000 0x1000>, - <0x1a200000 0x1000>; - interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>; - clock-names = "core", "iface"; - status = "disabled"; - }; - - i2c@1a280000 { - compatible = "qcom,i2c-qup-v1.1.1"; - reg = <0x1a280000 0x1000>; - interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>; - - clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>; - clock-names = "core", "iface"; - status = "disabled"; - - #address-cells = <1>; - #size-cells = <0>; - }; - - spi@1a280000 { - compatible = "qcom,spi-qup-v1.1.1"; - reg = <0x1a280000 0x1000>; - interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>; - - clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>; - clock-names = "core", "iface"; - status = "disabled"; - - #address-cells = <1>; - #size-cells = <0>; - }; - }; - gsbi6: gsbi@16500000 { compatible = "qcom,gsbi-v1.0.0"; reg = <0x16500000 0x100>;
@@ -784,149 +955,119 @@ gsbi7_i2c: i2c@16680000 { }; }; - rng@1a500000 { - compatible = "qcom,prng"; - reg = <0x1a500000 0x200>; - clocks = <&gcc PRNG_CLK>; - clock-names = "core"; - }; + adm_dma: dma-controller@18300000 { + compatible = "qcom,adm"; + reg = <0x18300000 0x100000>; + interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>; + #dma-cells = <1>; - sata_phy: sata-phy@1b400000 { - compatible = "qcom,ipq806x-sata-phy"; - reg = <0x1b400000 0x200>; + clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>; + clock-names = "core", "iface"; - clocks = <&gcc SATA_PHY_CFG_CLK>; - clock-names = "cfg"; + resets = <&gcc ADM0_RESET>, + <&gcc ADM0_PBUS_RESET>, + <&gcc ADM0_C0_RESET>, + <&gcc ADM0_C1_RESET>, + <&gcc ADM0_C2_RESET>; + reset-names = "clk", "pbus", "c0", "c1", "c2"; + qcom,ee = <0>; - #phy-cells = <0>; status = "disabled"; }; - nand: nand-controller@1ac00000 { - compatible = "qcom,ipq806x-nand"; - reg = <0x1ac00000 0x800>; - - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - - clocks = <&gcc EBI2_CLK>, - <&gcc EBI2_AON_CLK>; - clock-names = "core", "aon"; - - dmas = <&adm_dma 3>; - dma-names = "rxtx"; - qcom,cmd-crci = <15>; - qcom,data-crci = <3>; - + gsbi5: gsbi@1a200000 { + compatible = "qcom,gsbi-v1.0.0"; + cell-index = <5>; + reg = <0x1a200000 0x100>; + clocks = <&gcc GSBI5_H_CLK>; + clock-names = "iface"; #address-cells = <1>; - #size-cells = <0>; - + #size-cells = <1>; + ranges; status = "disabled"; - }; - sata: sata@29000000 { - compatible = "qcom,ipq806x-ahci", "generic-ahci"; - reg = <0x29000000 0x180>; + syscon-tcsr = <&tcsr>; - interrupts = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>; + gsbi5_serial: serial@1a240000 { + compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; + reg = <0x1a240000 0x1000>, + <0x1a200000 0x1000>; + interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>; + clock-names = "core", "iface"; + status = "disabled"; + }; - clocks = <&gcc SFAB_SATA_S_H_CLK>, - <&gcc SATA_H_CLK>, - <&gcc SATA_A_CLK>, - <&gcc SATA_RXOOB_CLK>, - <&gcc SATA_PMALIVE_CLK>; - clock-names = "slave_face", "iface", "core", - "rxoob", "pmalive"; + i2c@1a280000 { + compatible = "qcom,i2c-qup-v1.1.1"; + reg = <0x1a280000 0x1000>; + interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>; - assigned-clocks = <&gcc SATA_RXOOB_CLK>, <&gcc SATA_PMALIVE_CLK>; - assigned-clock-rates = <100000000>, <100000000>; + clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>; + clock-names = "core", "iface"; + status = "disabled"; - phys = <&sata_phy>; - phy-names = "sata-phy"; - status = "disabled"; - }; + #address-cells = <1>; + #size-cells = <0>; + }; - qcom,ssbi@500000 { - compatible = "qcom,ssbi"; - reg = <0x00500000 0x1000>; - qcom,controller-type = "pmic-arbiter"; - }; + spi@1a280000 { + compatible = "qcom,spi-qup-v1.1.1"; + reg = <0x1a280000 0x1000>; + interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>; - qfprom: qfprom@700000 { - compatible = "qcom,ipq8064-qfprom", "qcom,qfprom"; - reg = <0x00700000 0x1000>; - #address-cells = <1>; - #size-cells = <1>; - speedbin_efuse: speedbin@c0 { - reg = <0xc0 0x4>; - }; - tsens_calib: calib@400 { - reg = <0x400 0xb>; - }; - tsens_calib_backup: calib_backup@410 { - reg = <0x410 0xb>; + clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>; + clock-names = "core", "iface"; + status = "disabled"; + + #address-cells = <1>; + #size-cells = <0>; }; }; - gcc: clock-controller@900000 { - compatible = "qcom,gcc-ipq8064", "syscon"; - clocks = <&pxo_board>, <&cxo_board>; - clock-names = "pxo", "cxo"; - reg = <0x00900000 0x4000>; - #clock-cells = <1>; - #reset-cells = <1>; - #power-domain-cells = <1>; - - tsens: thermal-sensor@900000 { - compatible = "qcom,ipq8064-tsens"; - - nvmem-cells = <&tsens_calib>, <&tsens_calib_backup>; - nvmem-cell-names = "calib", "calib_backup"; - interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "uplow"; + tcsr: syscon@1a400000 { + compatible = "qcom,tcsr-ipq8064", "syscon"; + reg = <0x1a400000 0x100>; + }; - #qcom,sensors = <11>; - #thermal-sensor-cells = <1>; - }; + rng@1a500000 { + compatible = "qcom,prng"; + reg = <0x1a500000 0x200>; + clocks = <&gcc PRNG_CLK>; + clock-names = "core"; }; - rpm: rpm@108000 { - compatible = "qcom,rpm-ipq8064"; - reg = <0x108000 0x1000>; - qcom,ipc = <&l2cc 0x8 2>; + nand: nand-controller@1ac00000 { + compatible = "qcom,ipq806x-nand"; + reg = <0x1ac00000 0x800>; - interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "ack", "err", "wakeup"; + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; - clocks = <&gcc RPM_MSG_RAM_H_CLK>; - clock-names = "ram"; + clocks = <&gcc EBI2_CLK>, + <&gcc EBI2_AON_CLK>; + clock-names = "core", "aon"; + + dmas = <&adm_dma 3>; + dma-names = "rxtx"; + qcom,cmd-crci = <15>; + qcom,data-crci = <3>; - rpmcc: clock-controller { - compatible = "qcom,rpmcc-ipq806x", "qcom,rpmcc"; - #clock-cells = <1>; - }; - }; + #address-cells = <1>; + #size-cells = <0>; - tcsr: syscon@1a400000 { - compatible = "qcom,tcsr-ipq8064", "syscon"; - reg = <0x1a400000 0x100>; + status = "disabled"; }; - l2cc: clock-controller@2011000 { - compatible = "qcom,kpss-gcc", "syscon"; - reg = <0x2011000 0x1000>; - clocks = <&gcc PLL8_VOTE>, <&pxo_board>; - clock-names = "pll8_vote", "pxo"; - clock-output-names = "acpu_l2_aux"; - }; + sata_phy: sata-phy@1b400000 { + compatible = "qcom,ipq806x-sata-phy"; + reg = <0x1b400000 0x200>; - lcc: clock-controller@28000000 { - compatible = "qcom,lcc-ipq8064"; - reg = <0x28000000 0x1000>; - #clock-cells = <1>; - #reset-cells = <1>; + clocks = <&gcc SATA_PHY_CFG_CLK>; + clock-names = "cfg"; + + #phy-cells = <0>; + status = "disabled"; }; pcie0: pci@1b500000 {
@@ -1082,20 +1223,53 @@ pcie2: pci@1b900000 { perst-gpio = <&qcom_pinmux 63 GPIO_ACTIVE_LOW>; }; - nss_common: syscon@03000000 { - compatible = "syscon"; - reg = <0x03000000 0x0000FFFF>; - }; - qsgmii_csr: syscon@1bb00000 { compatible = "syscon"; reg = <0x1bb00000 0x000001FF>; }; - stmmac_axi_setup: stmmac-axi-config { - snps,wr_osr_lmt = <7>; - snps,rd_osr_lmt = <7>; - snps,blen = <16 0 0 0 0 0 0>; + lcc: clock-controller@28000000 { + compatible = "qcom,lcc-ipq8064"; + reg = <0x28000000 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + lpass@28100000 { + compatible = "qcom,lpass-cpu"; + status = "disabled"; + clocks = <&lcc AHBIX_CLK>, + <&lcc MI2S_OSR_CLK>, + <&lcc MI2S_BIT_CLK>; + clock-names = "ahbix-clk", + "mi2s-osr-clk", + "mi2s-bit-clk"; + interrupts = <GIC_SPI 85 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "lpass-irq-lpaif"; + reg = <0x28100000 0x10000>; + reg-names = "lpass-lpaif"; + }; + + sata: sata@29000000 { + compatible = "qcom,ipq806x-ahci", "generic-ahci"; + reg = <0x29000000 0x180>; + + interrupts = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc SFAB_SATA_S_H_CLK>, + <&gcc SATA_H_CLK>, + <&gcc SATA_A_CLK>, + <&gcc SATA_RXOOB_CLK>, + <&gcc SATA_PMALIVE_CLK>; + clock-names = "slave_face", "iface", "core", + "rxoob", "pmalive"; + + assigned-clocks = <&gcc SATA_RXOOB_CLK>, <&gcc SATA_PMALIVE_CLK>; + assigned-clock-rates = <100000000>, <100000000>; + + phys = <&sata_phy>; + phy-names = "sata-phy"; + status = "disabled"; }; gmac0: ethernet@37000000 {
@@ -1193,179 +1367,5 @@ gmac3: ethernet@37600000 { status = "disabled"; }; - - hs_phy_0: phy@100f8800 { - compatible = "qcom,ipq806x-usb-phy-hs"; - reg = <0x100f8800 0x30>; - clocks = <&gcc USB30_0_UTMI_CLK>; - clock-names = "ref"; - #phy-cells = <0>; - - status = "disabled"; - }; - - ss_phy_0: phy@100f8830 { - compatible = "qcom,ipq806x-usb-phy-ss"; - reg = <0x100f8830 0x30>; - clocks = <&gcc USB30_0_MASTER_CLK>; - clock-names = "ref"; - #phy-cells = <0>; - - status = "disabled"; - }; - - usb3_0: usb3@100f8800 { - compatible = "qcom,ipq8064-dwc3", "qcom,dwc3"; - #address-cells = <1>; - #size-cells = <1>; - reg = <0x100f8800 0x8000>; - clocks = <&gcc USB30_0_MASTER_CLK>; - clock-names = "core"; - - ranges; - - resets = <&gcc USB30_0_MASTER_RESET>; - reset-names = "master"; - - status = "disabled"; - - dwc3_0: dwc3@10000000 { - compatible = "snps,dwc3"; - reg = <0x10000000 0xcd00>; - interrupts = <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>; - phys = <&hs_phy_0>, <&ss_phy_0>; - phy-names = "usb2-phy", "usb3-phy"; - dr_mode = "host"; - snps,dis_u3_susphy_quirk; - }; - }; - - hs_phy_1: phy@110f8800 { - compatible = "qcom,ipq806x-usb-phy-hs"; - reg = <0x110f8800 0x30>; - clocks = <&gcc USB30_1_UTMI_CLK>; - clock-names = "ref"; - #phy-cells = <0>; - - status = "disabled"; - }; - - ss_phy_1: phy@110f8830 { - compatible = "qcom,ipq806x-usb-phy-ss"; - reg = <0x110f8830 0x30>; - clocks = <&gcc USB30_1_MASTER_CLK>; - clock-names = "ref"; - #phy-cells = <0>; - - status = "disabled"; - }; - - usb3_1: usb3@110f8800 { - compatible = "qcom,ipq8064-dwc3", "qcom,dwc3"; - #address-cells = <1>; - #size-cells = <1>; - reg = <0x110f8800 0x8000>; - clocks = <&gcc USB30_1_MASTER_CLK>; - clock-names = "core"; - - ranges; - - resets = <&gcc USB30_1_MASTER_RESET>; - reset-names = "master"; - - status = "disabled"; - - dwc3_1: dwc3@11000000 { - compatible = "snps,dwc3"; - reg = <0x11000000 0xcd00>; - interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; - phys = <&hs_phy_1>, <&ss_phy_1>; - phy-names = "usb2-phy", "usb3-phy"; - dr_mode = "host"; - snps,dis_u3_susphy_quirk; - }; - }; - - vsdcc_fixed: vsdcc-regulator { - compatible = "regulator-fixed"; - regulator-name = "SDCC Power"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - }; - - sdcc1bam: dma-controller@12402000 { - compatible = "qcom,bam-v1.3.0"; - reg = <0x12402000 0x8000>; - interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&gcc SDC1_H_CLK>; - clock-names = "bam_clk"; - #dma-cells = <1>; - qcom,ee = <0>; - }; - - sdcc3bam: dma-controller@12182000 { - compatible = "qcom,bam-v1.3.0"; - reg = <0x12182000 0x8000>; - interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&gcc SDC3_H_CLK>; - clock-names = "bam_clk"; - #dma-cells = <1>; - qcom,ee = <0>; - }; - - amba: amba { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <1>; - ranges; - - sdcc1: mmc@12400000 { - status = "disabled"; - compatible = "arm,pl18x", "arm,primecell"; - arm,primecell-periphid = <0x00051180>; - reg = <0x12400000 0x2000>; - interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "cmd_irq"; - clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>; - clock-names = "mclk", "apb_pclk"; - bus-width = <8>; - max-frequency = <96000000>; - non-removable; - cap-sd-highspeed; - cap-mmc-highspeed; - mmc-ddr-1_8v; - vmmc-supply = <&vsdcc_fixed>; - dmas = <&sdcc1bam 2>, <&sdcc1bam 1>; - dma-names = "tx", "rx"; - }; - - sdcc3: mmc@12180000 { - compatible = "arm,pl18x", "arm,primecell"; - arm,primecell-periphid = <0x00051180>; - status = "disabled"; - reg = <0x12180000 0x2000>; - interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "cmd_irq"; - clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>; - clock-names = "mclk", "apb_pclk"; - bus-width = <8>; - cap-sd-highspeed; - cap-mmc-highspeed; - max-frequency = <192000000>; - sd-uhs-sdr104; - sd-uhs-ddr50; - vqmmc-supply = <&vsdcc_fixed>; - dmas = <&sdcc3bam 2>, <&sdcc3bam 1>; - dma-names = "tx", "rx"; - }; - }; - - sfpb_mutex: hwlock@1200600 { - compatible = "qcom,sfpb-mutex"; - reg = <0x01200600 0x100>; - - #hwlock-cells = <1>; - }; }; };
Signature · 1 line
2.36.1
PATCH 2/2 ARM: dts: qcom: ipq8064: pad addresses to 8 digit
Pad reg addresses to 8 digit to make sorting easier.
--- arch/arm/boot/dts/qcom-ipq8064.dtsi | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-)
arch/arm/boot/dts/qcom-ipq8064.dtsi +3 -3
@@ -348,7 +348,7 @@ vsdcc_fixed: vsdcc-regulator { rpm: rpm@108000 { compatible = "qcom,rpm-ipq8064"; - reg = <0x108000 0x1000>; + reg = <0x00108000 0x1000>; qcom,ipc = <&l2cc 0x8 2>; interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
@@ -389,7 +389,7 @@ tsens_calib_backup: calib_backup@410 { qcom_pinmux: pinmux@800000 { compatible = "qcom,ipq8064-pinctrl"; - reg = <0x800000 0x4000>; + reg = <0x00800000 0x4000>; gpio-controller; gpio-ranges = <&qcom_pinmux 0 0 69>;
@@ -571,7 +571,7 @@ IRQ_TYPE_EDGE_RISING)>, l2cc: clock-controller@2011000 { compatible = "qcom,kpss-gcc", "syscon"; - reg = <0x2011000 0x1000>; + reg = <0x02011000 0x1000>; clocks = <&gcc PLL8_VOTE>, <&pxo_board>; clock-names = "pll8_vote", "pxo"; clock-output-names = "acpu_l2_aux";
Signature · 1 line
2.36.1
Re: [PATCH 2/2] ARM: dts: qcom: ipq8064: pad addresses to 8 digit
Quoted 1 line · Christian Marangi
Pad reg addresses to 8 digit to make sorting easier.
Please put this patch before the patch 1/2. It makes reviewing easier. Otherwise:
Quoted 37 lines
Signed-off-by Christian Marangi <[email protected]>--- arch/arm/boot/dts/qcom-ipq8064.dtsi | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-)arch/arm/boot/dts/qcom-ipq8064.dtsi +3
-3@@ -348,7 +348,7 @@ vsdcc_fixed: vsdcc-regulator { rpm: rpm@108000 { compatible = "qcom,rpm-ipq8064"; - reg = <0x108000 0x1000>; + reg = <0x00108000 0x1000>; qcom,ipc = <&l2cc 0x8 2>; interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,@@ -389,7 +389,7 @@ tsens_calib_backup: calib_backup@410 { qcom_pinmux: pinmux@800000 { compatible = "qcom,ipq8064-pinctrl"; - reg = <0x800000 0x4000>; + reg = <0x00800000 0x4000>; gpio-controller; gpio-ranges = <&qcom_pinmux 0 0 69>;@@ -571,7 +571,7 @@ IRQ_TYPE_EDGE_RISING)>, l2cc: clock-controller@2011000 { compatible = "qcom,kpss-gcc", "syscon"; - reg = <0x2011000 0x1000>; + reg = <0x02011000 0x1000>; clocks = <&gcc PLL8_VOTE>, <&pxo_board>; clock-names = "pll8_vote", "pxo"; clock-output-names = "acpu_l2_aux";
Signature · 2 lines
With best wishes Dmitry
Quoted 8 lines · Christian Marangi
Reorganize node order and sort them by address.
Signed-off-by Christian Marangi <[email protected]>---
This was picked from for-next qcom branch [1]. Reorganize dtsi as requested.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux.git/?h=for-next
If this is picked by qcom branch, no need to resend it.
I don't see value in such reshuffle. Reviewing is not possible and you did not mention tests (results should be equal).
Best regards,
Krzysztof
Quoted 7 lines · Krzysztof Kozlowski
Quoted 5 lines · Christian Marangi
Reorganize node order and sort them by address.
Signed-off-by Christian Marangi <[email protected]>---
Quoted 8 lines
Quoted 3 lines
This was picked from for-next qcom branch [1]. Reorganize dtsi as requested.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux.git/?h=for-next
If this is picked by qcom branch, no need to resend it.
I don't see value in such reshuffle. Reviewing is not possible and you did not mention tests (results should be equal).
The value is usual for all the cleanups: make it follow the established practice.
Signature · 2 lines
With best wishes Dmitry
Quoted 13 lines · Dmitry Baryshkov
Quoted 11 lines · Krzysztof Kozlowski
Quoted 8 lines · Christian Marangi
Reorganize node order and sort them by address.
Signed-off-by Christian Marangi <[email protected]>---
This was picked from for-next qcom branch [1]. Reorganize dtsi as requested.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux.git/?h=for-next
Quoted 7 lines
Quoted 4 lines
If this is picked by qcom branch, no need to resend it.
I don't see value in such reshuffle. Reviewing is not possible and you did not mention tests (results should be equal).
The value is usual for all the cleanups: make it follow the established practice.
Are you sure this is established practice? New DTSI files (see SC8280XP, sm8450 although sc7280 looked ordered) do not always follow it, so why imposing it for existing code? Such reshuffle can cause conflicts thus stops parallel development. Review is close to impossible...
Best regards,
Krzysztof
Quoted 16 lines · Krzysztof Kozlowski
Quoted 15 lines · Dmitry Baryshkov
Quoted 13 lines · Krzysztof Kozlowski
Quoted 8 lines · Christian Marangi
Reorganize node order and sort them by address.
Signed-off-by Christian Marangi <[email protected]>---
This was picked from for-next qcom branch [1]. Reorganize dtsi as requested.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux.git/?h=for-next
If this is picked by qcom branch, no need to resend it.
Quoted 7 lines
Quoted 5 lines
Quoted 2 lines
I don't see value in such reshuffle. Reviewing is not possible and you did not mention tests (results should be equal).
The value is usual for all the cleanups: make it follow the established practice.
Are you sure this is established practice?
Yes.
New DTSI files (see SC8280XP,
Quoted 2 lines
sm8450 although sc7280 looked ordered) do not always follow it, so why imposing it for existing code?
Perhaps it slipped through review.. Partially my bad.
Such reshuffle can cause conflicts thus
Quoted 1 line
stops parallel development. Review is close to impossible...
Almost any addition or removal also causes conflicts, because git is not as smart as we would like it to be. If the commit is structured properly (i.e. it *only* changes the order and nothing else), decompiling the dtbs before and after applying it and using a tool like meld that can find similar chunks of text at different offsets review is definitely possible, though not very pleasant (you can't just diff them, as order is preserved & phandles change due to that) as you have to look at it manually and can't tell much by just taking a look at the email.
Konrad
Quoted 3 lines
Best regards,
Krzysztof
Quoted 36 lines · Konrad Dybcio
Quoted 16 lines · Krzysztof Kozlowski
Quoted 15 lines · Dmitry Baryshkov
Quoted 13 lines · Krzysztof Kozlowski
Quoted 8 lines · Christian Marangi
Reorganize node order and sort them by address.
Signed-off-by Christian Marangi <[email protected]>---
This was picked from for-next qcom branch [1]. Reorganize dtsi as requested.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux.git/?h=for-next
If this is picked by qcom branch, no need to resend it.
Quoted 7 lines
Quoted 5 lines
Quoted 2 lines
I don't see value in such reshuffle. Reviewing is not possible and you did not mention tests (results should be equal).
The value is usual for all the cleanups: make it follow the established practice.
Are you sure this is established practice?
Yes.
New DTSI files (see SC8280XP,
Quoted 2 lines
sm8450 although sc7280 looked ordered) do not always follow it, so why imposing it for existing code?
Perhaps it slipped through review.. Partially my bad.
Such reshuffle can cause conflicts thus
Quoted 1 line
stops parallel development. Review is close to impossible...
Quoted 10 lines
Almost any addition or removal also causes conflicts, because git is not as smart as we would like it to be. If the commit is structured properly (i.e. it *only* changes the order and nothing else), decompiling the dtbs before and after applying it and using a tool like meld that can find similar chunks of text at different offsets review is definitely possible, though not very pleasant (you can't just diff them, as order is preserved & phandles change due to that) as you have to look at it manually and can't tell much by just taking a look at the email.
Can you give me an example of such tool? So I can put these data in the commit description. I have to rebase this anyway as more changes got merged so it might be a good idea to add more info about how this won't make actualy changes.
Quoted 4 lines
Konrad
Quoted 3 lines
Best regards,
Krzysztof
Signature · 1 line
Ansuel
Quoted 48 lines · Christian Marangi
Quoted 36 lines · Konrad Dybcio
Quoted 16 lines · Krzysztof Kozlowski
Quoted 15 lines · Dmitry Baryshkov
Quoted 13 lines · Krzysztof Kozlowski
Quoted 8 lines · Christian Marangi
Reorganize node order and sort them by address.
Signed-off-by Christian Marangi <[email protected]>---
This was picked from for-next qcom branch [1]. Reorganize dtsi as requested.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux.git/?h=for-next
If this is picked by qcom branch, no need to resend it.
Quoted 7 lines
Quoted 5 lines
Quoted 2 lines
I don't see value in such reshuffle. Reviewing is not possible and you did not mention tests (results should be equal).
The value is usual for all the cleanups: make it follow the established practice.
Are you sure this is established practice?
Yes.
New DTSI files (see SC8280XP,
Quoted 2 lines
sm8450 although sc7280 looked ordered) do not always follow it, so why imposing it for existing code?
Perhaps it slipped through review.. Partially my bad.
Such reshuffle can cause conflicts thus
Quoted 1 line
stops parallel development. Review is close to impossible...
Quoted 10 lines
Almost any addition or removal also causes conflicts, because git is not as smart as we would like it to be. If the commit is structured properly (i.e. it *only* changes the order and nothing else), decompiling the dtbs before and after applying it and using a tool like meld that can find similar chunks of text at different offsets review is definitely possible, though not very pleasant (you can't just diff them, as order is preserved & phandles change due to that) as you have to look at it manually and can't tell much by just taking a look at the email.
Quoted 4 lines
Can you give me an example of such tool? So I can put these data in the commit description. I have to rebase this anyway as more changes got merged so it might be a good idea to add more info about how this won't make actualy changes.
dtc -I dtb filename.dtb -O dts > outfile.dts
meld old.dts new.dts
Then you have to look at them side by side.
Alternatively, python has libfdt and one could make a tool for that particular usecase..
Konrad
Quoted 6 lines
Quoted 5 lines
Konrad
Quoted 3 lines
Best regards,
Krzysztof
Quoted 48 lines · Christian Marangi
Quoted 36 lines · Konrad Dybcio
Quoted 16 lines · Krzysztof Kozlowski
Quoted 15 lines · Dmitry Baryshkov
Quoted 13 lines · Krzysztof Kozlowski
Quoted 8 lines · Christian Marangi
Reorganize node order and sort them by address.
Signed-off-by Christian Marangi <[email protected]>---
This was picked from for-next qcom branch [1]. Reorganize dtsi as requested.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux.git/?h=for-next
If this is picked by qcom branch, no need to resend it.
Quoted 7 lines
Quoted 5 lines
Quoted 2 lines
I don't see value in such reshuffle. Reviewing is not possible and you did not mention tests (results should be equal).
The value is usual for all the cleanups: make it follow the established practice.
Are you sure this is established practice?
Yes.
New DTSI files (see SC8280XP,
Quoted 2 lines
sm8450 although sc7280 looked ordered) do not always follow it, so why imposing it for existing code?
Perhaps it slipped through review.. Partially my bad.
Such reshuffle can cause conflicts thus
Quoted 1 line
stops parallel development. Review is close to impossible...
Quoted 10 lines
Almost any addition or removal also causes conflicts, because git is not as smart as we would like it to be. If the commit is structured properly (i.e. it *only* changes the order and nothing else), decompiling the dtbs before and after applying it and using a tool like meld that can find similar chunks of text at different offsets review is definitely possible, though not very pleasant (you can't just diff them, as order is preserved & phandles change due to that) as you have to look at it manually and can't tell much by just taking a look at the email.
Quoted 5 lines
Can you give me an example of such tool? So I can put these data in the commit description. I have to rebase this anyway as more changes got merged so it might be a good idea to add more info about how this won't make actualy changes.
scripts/dtc/dtx_diff
fdtdump + diff
There should be an empty diff from at least one of methods above. If you have a difference, I am not sure how can we verify this.
Best regards,
Krzysztof
Quoted 58 lines · Krzysztof Kozlowski
Quoted 48 lines · Christian Marangi
Quoted 36 lines · Konrad Dybcio
Quoted 16 lines · Krzysztof Kozlowski
Quoted 15 lines · Dmitry Baryshkov
Quoted 13 lines · Krzysztof Kozlowski
Quoted 8 lines · Christian Marangi
Reorganize node order and sort them by address.
Signed-off-by Christian Marangi <[email protected]>---
This was picked from for-next qcom branch [1]. Reorganize dtsi as requested.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux.git/?h=for-next
If this is picked by qcom branch, no need to resend it.
Quoted 7 lines
Quoted 5 lines
Quoted 2 lines
I don't see value in such reshuffle. Reviewing is not possible and you did not mention tests (results should be equal).
The value is usual for all the cleanups: make it follow the established practice.
Are you sure this is established practice?
Yes.
New DTSI files (see SC8280XP,
Quoted 2 lines
sm8450 although sc7280 looked ordered) do not always follow it, so why imposing it for existing code?
Perhaps it slipped through review.. Partially my bad.
Such reshuffle can cause conflicts thus
Quoted 1 line
stops parallel development. Review is close to impossible...
Quoted 10 lines
Almost any addition or removal also causes conflicts, because git is not as smart as we would like it to be. If the commit is structured properly (i.e. it *only* changes the order and nothing else), decompiling the dtbs before and after applying it and using a tool like meld that can find similar chunks of text at different offsets review is definitely possible, though not very pleasant (you can't just diff them, as order is preserved & phandles change due to that) as you have to look at it manually and can't tell much by just taking a look at the email.
Quoted 5 lines
Can you give me an example of such tool? So I can put these data in the commit description. I have to rebase this anyway as more changes got merged so it might be a good idea to add more info about how this won't make actualy changes.
scripts/dtc/dtx_diff
fdtdump + diff
Quoted 6 lines
There should be an empty diff from at least one of methods above. If you have a difference, I am not sure how can we verify this.
Best regards,
Krzysztof
This [1] is the output of dtx_diff.
The file diff is just phanle change that are related to the node order.
Seems a nice way to verify if the shuffle didn't drop any node.
[1] https://gist.github.com/Ansuel/5ea821af51b8126292f4b3cd57e18555
Signature · 1 line
Ansuel
Quoted 63 lines · Christian Marangi
Quoted 62 lines · Krzysztof Kozlowski
Quoted 48 lines · Christian Marangi
Quoted 36 lines · Konrad Dybcio
Quoted 16 lines · Krzysztof Kozlowski
Quoted 15 lines · Dmitry Baryshkov
Quoted 13 lines · Krzysztof Kozlowski
Quoted 8 lines · Christian Marangi
Reorganize node order and sort them by address.
Signed-off-by Christian Marangi <[email protected]>---
This was picked from for-next qcom branch [1]. Reorganize dtsi as requested.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux.git/?h=for-next
If this is picked by qcom branch, no need to resend it.
Quoted 7 lines
Quoted 5 lines
Quoted 2 lines
I don't see value in such reshuffle. Reviewing is not possible and you did not mention tests (results should be equal).
The value is usual for all the cleanups: make it follow the established practice.
Are you sure this is established practice?
Yes.
New DTSI files (see SC8280XP,
Quoted 2 lines
sm8450 although sc7280 looked ordered) do not always follow it, so why imposing it for existing code?
Perhaps it slipped through review.. Partially my bad.
Such reshuffle can cause conflicts thus
Quoted 1 line
stops parallel development. Review is close to impossible...
Quoted 10 lines
Almost any addition or removal also causes conflicts, because git is not as smart as we would like it to be. If the commit is structured properly (i.e. it *only* changes the order and nothing else), decompiling the dtbs before and after applying it and using a tool like meld that can find similar chunks of text at different offsets review is definitely possible, though not very pleasant (you can't just diff them, as order is preserved & phandles change due to that) as you have to look at it manually and can't tell much by just taking a look at the email.
Quoted 5 lines
Can you give me an example of such tool? So I can put these data in the commit description. I have to rebase this anyway as more changes got merged so it might be a good idea to add more info about how this won't make actualy changes.
scripts/dtc/dtx_diff
fdtdump + diffThere should be an empty diff from at least one of methods above. If you have a difference, I am not sure how can we verify this.
Quoted 7 lines
Quoted 2 lines
Best regards,
KrzysztofThis [1] is the output of
dtx_diff.
The file diff is just phanle change that are related to the node order.Seems a nice way to verify if the shuffle didn't drop any node.
Therefore run the second method - fdtdump.
Best regards,
Krzysztof
Quoted 67 lines · Krzysztof Kozlowski
Quoted 66 lines · Christian Marangi
Quoted 64 lines · Krzysztof Kozlowski
Quoted 48 lines · Christian Marangi
Quoted 36 lines · Konrad Dybcio
Quoted 16 lines · Krzysztof Kozlowski
Quoted 15 lines · Dmitry Baryshkov
Quoted 13 lines · Krzysztof Kozlowski
Quoted 8 lines · Christian Marangi
Reorganize node order and sort them by address.
Signed-off-by Christian Marangi <[email protected]>---
This was picked from for-next qcom branch [1]. Reorganize dtsi as requested.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux.git/?h=for-next
If this is picked by qcom branch, no need to resend it.
Quoted 7 lines
Quoted 5 lines
Quoted 2 lines
I don't see value in such reshuffle. Reviewing is not possible and you did not mention tests (results should be equal).
The value is usual for all the cleanups: make it follow the established practice.
Are you sure this is established practice?
Yes.
New DTSI files (see SC8280XP,
Quoted 2 lines
sm8450 although sc7280 looked ordered) do not always follow it, so why imposing it for existing code?
Perhaps it slipped through review.. Partially my bad.
Such reshuffle can cause conflicts thus
Quoted 1 line
stops parallel development. Review is close to impossible...
Quoted 10 lines
Almost any addition or removal also causes conflicts, because git is not as smart as we would like it to be. If the commit is structured properly (i.e. it *only* changes the order and nothing else), decompiling the dtbs before and after applying it and using a tool like meld that can find similar chunks of text at different offsets review is definitely possible, though not very pleasant (you can't just diff them, as order is preserved & phandles change due to that) as you have to look at it manually and can't tell much by just taking a look at the email.
Quoted 5 lines
Can you give me an example of such tool? So I can put these data in the commit description. I have to rebase this anyway as more changes got merged so it might be a good idea to add more info about how this won't make actualy changes.
scripts/dtc/dtx_diff
fdtdump + diffThere should be an empty diff from at least one of methods above. If you have a difference, I am not sure how can we verify this.
Best regards,
Krzysztof
Quoted 7 lines
Quoted 4 lines
This [1] is the output of
dtx_diff.
The file diff is just phanle change that are related to the node order.Seems a nice way to verify if the shuffle didn't drop any node.
Therefore run the second method - fdtdump.
The output I have with fdtdump keeps the original node order so it doesn't produce correct correct diff as it will find difference with moved nodes. (unless i'm calling fdtdump or diff with the wrong args)
Quoted 2 lines
Best regards,
Krzysztof
Signature · 1 line
Ansuel
Quoted 49 lines · Krzysztof Kozlowski
Quoted 48 lines · Christian Marangi
Quoted 46 lines · Konrad Dybcio
Quoted 16 lines · Krzysztof Kozlowski
Quoted 15 lines · Dmitry Baryshkov
Quoted 13 lines · Krzysztof Kozlowski
Quoted 8 lines · Christian Marangi
Reorganize node order and sort them by address.
Signed-off-by Christian Marangi <[email protected]>---
This was picked from for-next qcom branch [1]. Reorganize dtsi as requested.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux.git/?h=for-next
If this is picked by qcom branch, no need to resend it.
Quoted 7 lines
Quoted 5 lines
Quoted 2 lines
I don't see value in such reshuffle. Reviewing is not possible and you did not mention tests (results should be equal).
The value is usual for all the cleanups: make it follow the established practice.
Are you sure this is established practice?
Yes.
New DTSI files (see SC8280XP,
Quoted 2 lines
sm8450 although sc7280 looked ordered) do not always follow it, so why imposing it for existing code?
Perhaps it slipped through review.. Partially my bad.
Such reshuffle can cause conflicts thus
Quoted 1 line
stops parallel development. Review is close to impossible...
Almost any addition or removal also causes conflicts, because git is not as smart as we would like it to be. If the commit is structured properly (i.e. it *only* changes the order and nothing else), decompiling the dtbs before and after applying it and using a tool like meld that can find similar chunks of text at different offsets review is definitely possible, though not very pleasant (you can't just diff them, as order is preserved & phandles change due to that) as you have to look at it manually and can't tell much by just taking a look at the email.
Quoted 8 lines
Quoted 5 lines
Can you give me an example of such tool? So I can put these data in the commit description. I have to rebase this anyway as more changes got merged so it might be a good idea to add more info about how this won't make actualy changes.
scripts/dtc/dtx_diff
fdtdump + diff
Thanks for sharing this.. way better than my crude method..
Konrad
Quoted 7 lines
There should be an empty diff from at least one of methods above. If you have a difference, I am not sure how can we verify this.
Best regards,
Krzysztof
Quoted 58 lines · Konrad Dybcio
Quoted 55 lines · Krzysztof Kozlowski
Quoted 53 lines · Christian Marangi
Quoted 36 lines · Konrad Dybcio
Quoted 16 lines · Krzysztof Kozlowski
Quoted 15 lines · Dmitry Baryshkov
Quoted 13 lines · Krzysztof Kozlowski
Quoted 8 lines · Christian Marangi
Reorganize node order and sort them by address.
Signed-off-by Christian Marangi <[email protected]>---
This was picked from for-next qcom branch [1]. Reorganize dtsi as requested.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux.git/?h=for-next
If this is picked by qcom branch, no need to resend it.
Quoted 7 lines
Quoted 5 lines
Quoted 2 lines
I don't see value in such reshuffle. Reviewing is not possible and you did not mention tests (results should be equal).
The value is usual for all the cleanups: make it follow the established practice.
Are you sure this is established practice?
Yes.
New DTSI files (see SC8280XP,
Quoted 2 lines
sm8450 although sc7280 looked ordered) do not always follow it, so why imposing it for existing code?
Perhaps it slipped through review.. Partially my bad.
Such reshuffle can cause conflicts thus
Quoted 1 line
stops parallel development. Review is close to impossible...
Quoted 10 lines
Almost any addition or removal also causes conflicts, because git is not as smart as we would like it to be. If the commit is structured properly (i.e. it *only* changes the order and nothing else), decompiling the dtbs before and after applying it and using a tool like meld that can find similar chunks of text at different offsets review is definitely possible, though not very pleasant (you can't just diff them, as order is preserved & phandles change due to that) as you have to look at it manually and can't tell much by just taking a look at the email.
Can you give me an example of such tool? So I can put these data in the commit description. I have to rebase this anyway as more changes got merged so it might be a good idea to add more info about how this won't make actualy changes.
Quoted 4 lines
Quoted 2 lines
scripts/dtc/dtx_diff
fdtdump + diffThanks for sharing this.. way better than my crude method..
For wide-tree cleanups I run (crosc64 is shortcut for proper env settings):
rm -fr dts-old; cp -r out/arch/arm64/boot/dts/ dts-old
crosc64 make -j8 dtbs
<make the changes / git stash pop / etc>
rm -fr dts-new; cp -r out/arch/arm64/boot/dts/ dts-new
crosc64 make -j8 dtbs
for i in dts-old/*/*dtb dts-old/*/*/*dtb; do echo $i; crosc64 scripts/dtc/dtx_diff ${i} dts-new/${i#dts-old/} ; done
Second method gives sometimes less false-positives:
for i in dts-old/*/*dtb dts-old/*/*/*dtb; do echo $i; crosc64 fdtdump ${i} > ${i}.fdt ; crosc64 fdtdump dts-new/${i#dts-old/} > dts-new/${i#dts-old/}.fdt ; diff -ubB ${i}.fdt dts-new/${i#dts-old/}.fdt ; done
Best regards,
Krzysztof
Quoted 6 lines · Krzysztof Kozlowski
Quoted 5 lines · Christian Marangi
Reorganize node order and sort them by address.
Signed-off-by Christian Marangi <[email protected]>---
Quoted 10 lines
Quoted 3 lines
This was picked from for-next qcom branch [1]. Reorganize dtsi as requested.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux.git/?h=for-next
If this is picked by qcom branch, no need to resend it.
I don't see value in such reshuffle. Reviewing is not possible and you did not mention tests (results should be equal).
Bjorn asked me if I could send a patch to sort the dtsi since it was a mess with the order. It's really just a node move with no implementation change. Also no code deleted/added.
Don't know if I should split this or add other thing to this. Just addressing a request from Bjorn.
Quoted 3 lines
Best regards,
Krzysztof
Signature · 1 line
Ansuel
Quoted 29 lines · Christian Marangi
Reorganize node order and sort them by address.
Signed-off-by Christian Marangi <[email protected]>---
This was picked from for-next qcom branch [1]. Reorganize dtsi as requested.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux.git/?h=for-next
arch/arm/boot/dts/qcom-ipq8064.dtsi | 766 ++++++++++++++-------------- 1 file changed, 383 insertions(+), 383 deletions(-)arch/arm/boot/dts/qcom-ipq8064.dtsi +0
-8@@ -332,19 +332,59 @@ soc: soc { ranges; compatible = "simple-bus"; - lpass@28100000 { - compatible = "qcom,lpass-cpu"; - status = "disabled"; - clocks = <&lcc AHBIX_CLK>, - <&lcc MI2S_OSR_CLK>, - <&lcc MI2S_BIT_CLK>; - clock-names = "ahbix-clk", - "mi2s-osr-clk",
arch/arm/boot/dts/qcom-ipq8064.dtsi soc: soc { · line 339
Quoted 10 lines
arch/arm/boot/dts/qcom-ipq8064.dtsi +5
-5- "mi2s-bit-clk"; - interrupts = <GIC_SPI 85 IRQ_TYPE_EDGE_RISING>; - interrupt-names = "lpass-irq-lpaif"; - reg = <0x28100000 0x10000>; - reg-names = "lpass-lpaif"; + stmmac_axi_setup: stmmac-axi-config { + snps,wr_osr_lmt = <7>; + snps,rd_osr_lmt = <7>; + snps,blen = <16 0 0 0 0 0 0>; + };
This one gave me troubles. This node represents settings common to all four GMAC. Maybe Krzysztof would have a different opinion here. I'd suggest breaking the order and putting it right after all gmac nodes.
arch/arm/boot/dts/qcom-ipq8064.dtsi soc: soc { · line 347
Quoted 8 lines
arch/arm/boot/dts/qcom-ipq8064.dtsi +8
-0+ + vsdcc_fixed: vsdcc-regulator { + compatible = "regulator-fixed"; + regulator-name = "SDCC Power"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + };
This should be moved outside of soc{} node. Usually all fixed-voltage regulators are part of /, not /soc/.
Quoted 167 lines
arch/arm/boot/dts/qcom-ipq8064.dtsi +119
-18+ + rpm: rpm@108000 { + compatible = "qcom,rpm-ipq8064"; + reg = <0x108000 0x1000>; + qcom,ipc = <&l2cc 0x8 2>; + + interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "ack", "err", "wakeup"; + + clocks = <&gcc RPM_MSG_RAM_H_CLK>; + clock-names = "ram"; + + rpmcc: clock-controller { + compatible = "qcom,rpmcc-ipq806x", "qcom,rpmcc"; + #clock-cells = <1>; + }; + }; + + qcom,ssbi@500000 { + compatible = "qcom,ssbi"; + reg = <0x00500000 0x1000>; + qcom,controller-type = "pmic-arbiter"; + }; + + qfprom: qfprom@700000 { + compatible = "qcom,ipq8064-qfprom", "qcom,qfprom"; + reg = <0x00700000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + speedbin_efuse: speedbin@c0 { + reg = <0xc0 0x4>; + }; + tsens_calib: calib@400 { + reg = <0x400 0xb>; + }; + tsens_calib_backup: calib_backup@410 { + reg = <0x410 0xb>; + }; }; qcom_pinmux: pinmux@800000 {@@ -471,6 +511,35 @@ mux { }; }; + gcc: clock-controller@900000 { + compatible = "qcom,gcc-ipq8064", "syscon"; + clocks = <&pxo_board>, <&cxo_board>; + clock-names = "pxo", "cxo"; + reg = <0x00900000 0x4000>; + #clock-cells = <1>; + #reset-cells = <1>; + #power-domain-cells = <1>; + + tsens: thermal-sensor@900000 { + compatible = "qcom,ipq8064-tsens"; + + nvmem-cells = <&tsens_calib>, <&tsens_calib_backup>; + nvmem-cell-names = "calib", "calib_backup"; + interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "uplow"; + + #qcom,sensors = <11>; + #thermal-sensor-cells = <1>; + }; + }; + + sfpb_mutex: hwlock@1200600 { + compatible = "qcom,sfpb-mutex"; + reg = <0x01200600 0x100>; + + #hwlock-cells = <1>; + }; + intc: interrupt-controller@2000000 { compatible = "qcom,msm-qgic2"; interrupt-controller;@@ -500,46 +569,198 @@ IRQ_TYPE_EDGE_RISING)>, cpu-offset = <0x80000>; }; + l2cc: clock-controller@2011000 { + compatible = "qcom,kpss-gcc", "syscon"; + reg = <0x2011000 0x1000>; + clocks = <&gcc PLL8_VOTE>, <&pxo_board>; + clock-names = "pll8_vote", "pxo"; + clock-output-names = "acpu_l2_aux"; + }; + acc0: clock-controller@2088000 { compatible = "qcom,kpss-acc-v1"; reg = <0x02088000 0x1000>, <0x02008000 0x1000>; }; + saw0: regulator@2089000 { + compatible = "qcom,saw2"; + reg = <0x02089000 0x1000>, <0x02009000 0x1000>; + regulator; + }; + acc1: clock-controller@2098000 { compatible = "qcom,kpss-acc-v1"; reg = <0x02098000 0x1000>, <0x02008000 0x1000>; }; - adm_dma: dma-controller@18300000 { - compatible = "qcom,adm"; - reg = <0x18300000 0x100000>; - interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>; - #dma-cells = <1>; + saw1: regulator@2099000 { + compatible = "qcom,saw2"; + reg = <0x02099000 0x1000>, <0x02009000 0x1000>; + regulator; + }; - clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>; - clock-names = "core", "iface"; + nss_common: syscon@03000000 { + compatible = "syscon"; + reg = <0x03000000 0x0000FFFF>; + }; - resets = <&gcc ADM0_RESET>, - <&gcc ADM0_PBUS_RESET>, - <&gcc ADM0_C0_RESET>, - <&gcc ADM0_C1_RESET>, - <&gcc ADM0_C2_RESET>; - reset-names = "clk", "pbus", "c0", "c1", "c2"; - qcom,ee = <0>; + usb3_0: usb3@100f8800 { + compatible = "qcom,ipq8064-dwc3", "qcom,dwc3"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x100f8800 0x8000>; + clocks = <&gcc USB30_0_MASTER_CLK>; + clock-names = "core"; + + ranges; + + resets = <&gcc USB30_0_MASTER_RESET>; + reset-names = "master"; status = "disabled"; + + dwc3_0: dwc3@10000000 { + compatible = "snps,dwc3"; + reg = <0x10000000 0xcd00>; + interrupts = <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>; + phys = <&hs_phy_0>, <&ss_phy_0>; + phy-names = "usb2-phy", "usb3-phy"; + dr_mode = "host"; + snps,dis_u3_susphy_quirk; + }; }; - saw0: regulator@2089000 { - compatible = "qcom,saw2"; - reg = <0x02089000 0x1000>, <0x02009000 0x1000>; - regulator; + hs_phy_0: phy@100f8800 { + compatible = "qcom,ipq806x-usb-phy-hs"; + reg = <0x100f8800 0x30>; + clocks = <&gcc USB30_0_UTMI_CLK>; + clock-names = "ref";
arch/arm/boot/dts/qcom-ipq8064.dtsi IRQ_TYPE_EDGE_RISING)>, · line 643
Quoted 10 lines
arch/arm/boot/dts/qcom-ipq8064.dtsi +4
-4+ #phy-cells = <0>; + + status = "disabled"; }; - saw1: regulator@2099000 { - compatible = "qcom,saw2"; - reg = <0x02099000 0x1000>, <0x02009000 0x1000>; - regulator; + ss_phy_0: phy@100f8830 {
I do not quite understand the bindings here. Do we have the hs_phy at the same address as the usb3 device?
Judging by the ranges, both hs and ss PHYs should be usb child nodes. I do not expect that this will be fixed in this patchset, more of the issue to be taken care of later.
I see that dwc3-qcom.c touches the same registers as your phy-qcom-ipq806x-usb.c does. So... this should probably be changed.
Quoted 66 lines
arch/arm/boot/dts/qcom-ipq8064.dtsi +66
-0+ compatible = "qcom,ipq806x-usb-phy-ss"; + reg = <0x100f8830 0x30>; + clocks = <&gcc USB30_0_MASTER_CLK>; + clock-names = "ref"; + #phy-cells = <0>; + + status = "disabled"; + }; + + usb3_1: usb3@110f8800 { + compatible = "qcom,ipq8064-dwc3", "qcom,dwc3"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x110f8800 0x8000>; + clocks = <&gcc USB30_1_MASTER_CLK>; + clock-names = "core"; + + ranges; + + resets = <&gcc USB30_1_MASTER_RESET>; + reset-names = "master"; + + status = "disabled"; + + dwc3_1: dwc3@11000000 { + compatible = "snps,dwc3"; + reg = <0x11000000 0xcd00>; + interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; + phys = <&hs_phy_1>, <&ss_phy_1>; + phy-names = "usb2-phy", "usb3-phy"; + dr_mode = "host"; + snps,dis_u3_susphy_quirk; + }; + }; + + hs_phy_1: phy@110f8800 { + compatible = "qcom,ipq806x-usb-phy-hs"; + reg = <0x110f8800 0x30>; + clocks = <&gcc USB30_1_UTMI_CLK>; + clock-names = "ref"; + #phy-cells = <0>; + + status = "disabled"; + }; + + ss_phy_1: phy@110f8830 { + compatible = "qcom,ipq806x-usb-phy-ss"; + reg = <0x110f8830 0x30>; + clocks = <&gcc USB30_1_MASTER_CLK>; + clock-names = "ref"; + #phy-cells = <0>; + + status = "disabled"; + }; + + sdcc3bam: dma-controller@12182000 { + compatible = "qcom,bam-v1.3.0"; + reg = <0x12182000 0x8000>; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc SDC3_H_CLK>; + clock-names = "bam_clk"; + #dma-cells = <1>; + qcom,ee = <0>; + }; + + sdcc1bam: dma-controller@12402000 {
arch/arm/boot/dts/qcom-ipq8064.dtsi IRQ_TYPE_EDGE_RISING)>, · line 719
Quoted 10 lines
arch/arm/boot/dts/qcom-ipq8064.dtsi +10
-0+ compatible = "qcom,bam-v1.3.0"; + reg = <0x12402000 0x8000>; + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc SDC1_H_CLK>; + clock-names = "bam_clk"; + #dma-cells = <1>; + qcom,ee = <0>; + }; + + amba: amba {
I have the feeling that the amba node doesn't add anything here. Devices with close enough addresses (bam and sdcc) are split by this node.
I'd suggest dropping the amba{} part completely. Could you please prepend this series with a patch to drop amba{} node?
Quoted 585 lines
arch/arm/boot/dts/qcom-ipq8064.dtsi +171
-349+ compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + sdcc3: mmc@12180000 { + compatible = "arm,pl18x", "arm,primecell"; + arm,primecell-periphid = <0x00051180>; + status = "disabled"; + reg = <0x12180000 0x2000>; + interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "cmd_irq"; + clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>; + clock-names = "mclk", "apb_pclk"; + bus-width = <8>; + cap-sd-highspeed; + cap-mmc-highspeed; + max-frequency = <192000000>; + sd-uhs-sdr104; + sd-uhs-ddr50; + vqmmc-supply = <&vsdcc_fixed>; + dmas = <&sdcc3bam 2>, <&sdcc3bam 1>; + dma-names = "tx", "rx"; + }; + + sdcc1: mmc@12400000 { + status = "disabled"; + compatible = "arm,pl18x", "arm,primecell"; + arm,primecell-periphid = <0x00051180>; + reg = <0x12400000 0x2000>; + interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "cmd_irq"; + clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>; + clock-names = "mclk", "apb_pclk"; + bus-width = <8>; + max-frequency = <96000000>; + non-removable; + cap-sd-highspeed; + cap-mmc-highspeed; + mmc-ddr-1_8v; + vmmc-supply = <&vsdcc_fixed>; + dmas = <&sdcc1bam 2>, <&sdcc1bam 1>; + dma-names = "tx", "rx"; + }; }; gsbi1: gsbi@12440000 {@@ -654,56 +875,6 @@ i2c@16380000 { }; }; - gsbi5: gsbi@1a200000 { - compatible = "qcom,gsbi-v1.0.0"; - cell-index = <5>; - reg = <0x1a200000 0x100>; - clocks = <&gcc GSBI5_H_CLK>; - clock-names = "iface"; - #address-cells = <1>; - #size-cells = <1>; - ranges; - status = "disabled"; - - syscon-tcsr = <&tcsr>; - - gsbi5_serial: serial@1a240000 { - compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; - reg = <0x1a240000 0x1000>, - <0x1a200000 0x1000>; - interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>; - clock-names = "core", "iface"; - status = "disabled"; - }; - - i2c@1a280000 { - compatible = "qcom,i2c-qup-v1.1.1"; - reg = <0x1a280000 0x1000>; - interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>; - - clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>; - clock-names = "core", "iface"; - status = "disabled"; - - #address-cells = <1>; - #size-cells = <0>; - }; - - spi@1a280000 { - compatible = "qcom,spi-qup-v1.1.1"; - reg = <0x1a280000 0x1000>; - interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>; - - clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>; - clock-names = "core", "iface"; - status = "disabled"; - - #address-cells = <1>; - #size-cells = <0>; - }; - }; - gsbi6: gsbi@16500000 { compatible = "qcom,gsbi-v1.0.0"; reg = <0x16500000 0x100>;@@ -784,149 +955,119 @@ gsbi7_i2c: i2c@16680000 { }; }; - rng@1a500000 { - compatible = "qcom,prng"; - reg = <0x1a500000 0x200>; - clocks = <&gcc PRNG_CLK>; - clock-names = "core"; - }; + adm_dma: dma-controller@18300000 { + compatible = "qcom,adm"; + reg = <0x18300000 0x100000>; + interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>; + #dma-cells = <1>; - sata_phy: sata-phy@1b400000 { - compatible = "qcom,ipq806x-sata-phy"; - reg = <0x1b400000 0x200>; + clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>; + clock-names = "core", "iface"; - clocks = <&gcc SATA_PHY_CFG_CLK>; - clock-names = "cfg"; + resets = <&gcc ADM0_RESET>, + <&gcc ADM0_PBUS_RESET>, + <&gcc ADM0_C0_RESET>, + <&gcc ADM0_C1_RESET>, + <&gcc ADM0_C2_RESET>; + reset-names = "clk", "pbus", "c0", "c1", "c2"; + qcom,ee = <0>; - #phy-cells = <0>; status = "disabled"; }; - nand: nand-controller@1ac00000 { - compatible = "qcom,ipq806x-nand"; - reg = <0x1ac00000 0x800>; - - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - - clocks = <&gcc EBI2_CLK>, - <&gcc EBI2_AON_CLK>; - clock-names = "core", "aon"; - - dmas = <&adm_dma 3>; - dma-names = "rxtx"; - qcom,cmd-crci = <15>; - qcom,data-crci = <3>; - + gsbi5: gsbi@1a200000 { + compatible = "qcom,gsbi-v1.0.0"; + cell-index = <5>; + reg = <0x1a200000 0x100>; + clocks = <&gcc GSBI5_H_CLK>; + clock-names = "iface"; #address-cells = <1>; - #size-cells = <0>; - + #size-cells = <1>; + ranges; status = "disabled"; - }; - sata: sata@29000000 { - compatible = "qcom,ipq806x-ahci", "generic-ahci"; - reg = <0x29000000 0x180>; + syscon-tcsr = <&tcsr>; - interrupts = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>; + gsbi5_serial: serial@1a240000 { + compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; + reg = <0x1a240000 0x1000>, + <0x1a200000 0x1000>; + interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>; + clock-names = "core", "iface"; + status = "disabled"; + }; - clocks = <&gcc SFAB_SATA_S_H_CLK>, - <&gcc SATA_H_CLK>, - <&gcc SATA_A_CLK>, - <&gcc SATA_RXOOB_CLK>, - <&gcc SATA_PMALIVE_CLK>; - clock-names = "slave_face", "iface", "core", - "rxoob", "pmalive"; + i2c@1a280000 { + compatible = "qcom,i2c-qup-v1.1.1"; + reg = <0x1a280000 0x1000>; + interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>; - assigned-clocks = <&gcc SATA_RXOOB_CLK>, <&gcc SATA_PMALIVE_CLK>; - assigned-clock-rates = <100000000>, <100000000>; + clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>; + clock-names = "core", "iface"; + status = "disabled"; - phys = <&sata_phy>; - phy-names = "sata-phy"; - status = "disabled"; - }; + #address-cells = <1>; + #size-cells = <0>; + }; - qcom,ssbi@500000 { - compatible = "qcom,ssbi"; - reg = <0x00500000 0x1000>; - qcom,controller-type = "pmic-arbiter"; - }; + spi@1a280000 { + compatible = "qcom,spi-qup-v1.1.1"; + reg = <0x1a280000 0x1000>; + interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>; - qfprom: qfprom@700000 { - compatible = "qcom,ipq8064-qfprom", "qcom,qfprom"; - reg = <0x00700000 0x1000>; - #address-cells = <1>; - #size-cells = <1>; - speedbin_efuse: speedbin@c0 { - reg = <0xc0 0x4>; - }; - tsens_calib: calib@400 { - reg = <0x400 0xb>; - }; - tsens_calib_backup: calib_backup@410 { - reg = <0x410 0xb>; + clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>; + clock-names = "core", "iface"; + status = "disabled"; + + #address-cells = <1>; + #size-cells = <0>; }; }; - gcc: clock-controller@900000 { - compatible = "qcom,gcc-ipq8064", "syscon"; - clocks = <&pxo_board>, <&cxo_board>; - clock-names = "pxo", "cxo"; - reg = <0x00900000 0x4000>; - #clock-cells = <1>; - #reset-cells = <1>; - #power-domain-cells = <1>; - - tsens: thermal-sensor@900000 { - compatible = "qcom,ipq8064-tsens"; - - nvmem-cells = <&tsens_calib>, <&tsens_calib_backup>; - nvmem-cell-names = "calib", "calib_backup"; - interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "uplow"; + tcsr: syscon@1a400000 { + compatible = "qcom,tcsr-ipq8064", "syscon"; + reg = <0x1a400000 0x100>; + }; - #qcom,sensors = <11>; - #thermal-sensor-cells = <1>; - }; + rng@1a500000 { + compatible = "qcom,prng"; + reg = <0x1a500000 0x200>; + clocks = <&gcc PRNG_CLK>; + clock-names = "core"; }; - rpm: rpm@108000 { - compatible = "qcom,rpm-ipq8064"; - reg = <0x108000 0x1000>; - qcom,ipc = <&l2cc 0x8 2>; + nand: nand-controller@1ac00000 { + compatible = "qcom,ipq806x-nand"; + reg = <0x1ac00000 0x800>; - interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "ack", "err", "wakeup"; + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; - clocks = <&gcc RPM_MSG_RAM_H_CLK>; - clock-names = "ram"; + clocks = <&gcc EBI2_CLK>, + <&gcc EBI2_AON_CLK>; + clock-names = "core", "aon"; + + dmas = <&adm_dma 3>; + dma-names = "rxtx"; + qcom,cmd-crci = <15>; + qcom,data-crci = <3>; - rpmcc: clock-controller { - compatible = "qcom,rpmcc-ipq806x", "qcom,rpmcc"; - #clock-cells = <1>; - }; - }; + #address-cells = <1>; + #size-cells = <0>; - tcsr: syscon@1a400000 { - compatible = "qcom,tcsr-ipq8064", "syscon"; - reg = <0x1a400000 0x100>; + status = "disabled"; }; - l2cc: clock-controller@2011000 { - compatible = "qcom,kpss-gcc", "syscon"; - reg = <0x2011000 0x1000>; - clocks = <&gcc PLL8_VOTE>, <&pxo_board>; - clock-names = "pll8_vote", "pxo"; - clock-output-names = "acpu_l2_aux"; - }; + sata_phy: sata-phy@1b400000 { + compatible = "qcom,ipq806x-sata-phy"; + reg = <0x1b400000 0x200>; - lcc: clock-controller@28000000 { - compatible = "qcom,lcc-ipq8064"; - reg = <0x28000000 0x1000>; - #clock-cells = <1>; - #reset-cells = <1>; + clocks = <&gcc SATA_PHY_CFG_CLK>; + clock-names = "cfg"; + + #phy-cells = <0>; + status = "disabled"; }; pcie0: pci@1b500000 {@@ -1082,20 +1223,53 @@ pcie2: pci@1b900000 { perst-gpio = <&qcom_pinmux 63 GPIO_ACTIVE_LOW>; }; - nss_common: syscon@03000000 { - compatible = "syscon"; - reg = <0x03000000 0x0000FFFF>; - }; - qsgmii_csr: syscon@1bb00000 { compatible = "syscon"; reg = <0x1bb00000 0x000001FF>; }; - stmmac_axi_setup: stmmac-axi-config { - snps,wr_osr_lmt = <7>; - snps,rd_osr_lmt = <7>; - snps,blen = <16 0 0 0 0 0 0>; + lcc: clock-controller@28000000 { + compatible = "qcom,lcc-ipq8064"; + reg = <0x28000000 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + lpass@28100000 { + compatible = "qcom,lpass-cpu"; + status = "disabled"; + clocks = <&lcc AHBIX_CLK>, + <&lcc MI2S_OSR_CLK>, + <&lcc MI2S_BIT_CLK>; + clock-names = "ahbix-clk", + "mi2s-osr-clk", + "mi2s-bit-clk"; + interrupts = <GIC_SPI 85 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "lpass-irq-lpaif"; + reg = <0x28100000 0x10000>; + reg-names = "lpass-lpaif"; + }; + + sata: sata@29000000 { + compatible = "qcom,ipq806x-ahci", "generic-ahci"; + reg = <0x29000000 0x180>; + + interrupts = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc SFAB_SATA_S_H_CLK>, + <&gcc SATA_H_CLK>, + <&gcc SATA_A_CLK>, + <&gcc SATA_RXOOB_CLK>, + <&gcc SATA_PMALIVE_CLK>; + clock-names = "slave_face", "iface", "core", + "rxoob", "pmalive"; + + assigned-clocks = <&gcc SATA_RXOOB_CLK>, <&gcc SATA_PMALIVE_CLK>; + assigned-clock-rates = <100000000>, <100000000>; + + phys = <&sata_phy>; + phy-names = "sata-phy"; + status = "disabled"; }; gmac0: ethernet@37000000 {@@ -1193,179 +1367,5 @@ gmac3: ethernet@37600000 { status = "disabled"; }; - - hs_phy_0: phy@100f8800 { - compatible = "qcom,ipq806x-usb-phy-hs"; - reg = <0x100f8800 0x30>; - clocks = <&gcc USB30_0_UTMI_CLK>; - clock-names = "ref"; - #phy-cells = <0>; - - status = "disabled"; - }; - - ss_phy_0: phy@100f8830 { - compatible = "qcom,ipq806x-usb-phy-ss"; - reg = <0x100f8830 0x30>; - clocks = <&gcc USB30_0_MASTER_CLK>; - clock-names = "ref"; - #phy-cells = <0>; - - status = "disabled"; - }; - - usb3_0: usb3@100f8800 { - compatible = "qcom,ipq8064-dwc3", "qcom,dwc3"; - #address-cells = <1>; - #size-cells = <1>; - reg = <0x100f8800 0x8000>; - clocks = <&gcc USB30_0_MASTER_CLK>; - clock-names = "core"; - - ranges; - - resets = <&gcc USB30_0_MASTER_RESET>; - reset-names = "master"; - - status = "disabled"; - - dwc3_0: dwc3@10000000 { - compatible = "snps,dwc3"; - reg = <0x10000000 0xcd00>; - interrupts = <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>; - phys = <&hs_phy_0>, <&ss_phy_0>; - phy-names = "usb2-phy", "usb3-phy"; - dr_mode = "host"; - snps,dis_u3_susphy_quirk; - }; - }; - - hs_phy_1: phy@110f8800 { - compatible = "qcom,ipq806x-usb-phy-hs"; - reg = <0x110f8800 0x30>; - clocks = <&gcc USB30_1_UTMI_CLK>; - clock-names = "ref"; - #phy-cells = <0>; - - status = "disabled"; - }; - - ss_phy_1: phy@110f8830 { - compatible = "qcom,ipq806x-usb-phy-ss"; - reg = <0x110f8830 0x30>; - clocks = <&gcc USB30_1_MASTER_CLK>; - clock-names = "ref"; - #phy-cells = <0>; - - status = "disabled"; - }; - - usb3_1: usb3@110f8800 { - compatible = "qcom,ipq8064-dwc3", "qcom,dwc3"; - #address-cells = <1>; - #size-cells = <1>; - reg = <0x110f8800 0x8000>; - clocks = <&gcc USB30_1_MASTER_CLK>; - clock-names = "core"; - - ranges; - - resets = <&gcc USB30_1_MASTER_RESET>; - reset-names = "master"; - - status = "disabled"; - - dwc3_1: dwc3@11000000 { - compatible = "snps,dwc3"; - reg = <0x11000000 0xcd00>; - interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; - phys = <&hs_phy_1>, <&ss_phy_1>; - phy-names = "usb2-phy", "usb3-phy"; - dr_mode = "host"; - snps,dis_u3_susphy_quirk; - }; - }; - - vsdcc_fixed: vsdcc-regulator { - compatible = "regulator-fixed"; - regulator-name = "SDCC Power"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - }; - - sdcc1bam: dma-controller@12402000 { - compatible = "qcom,bam-v1.3.0"; - reg = <0x12402000 0x8000>; - interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&gcc SDC1_H_CLK>; - clock-names = "bam_clk"; - #dma-cells = <1>; - qcom,ee = <0>; - }; - - sdcc3bam: dma-controller@12182000 { - compatible = "qcom,bam-v1.3.0"; - reg = <0x12182000 0x8000>; - interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&gcc SDC3_H_CLK>; - clock-names = "bam_clk"; - #dma-cells = <1>; - qcom,ee = <0>; - }; - - amba: amba { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <1>; - ranges; - - sdcc1: mmc@12400000 { - status = "disabled"; - compatible = "arm,pl18x", "arm,primecell"; - arm,primecell-periphid = <0x00051180>; - reg = <0x12400000 0x2000>; - interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "cmd_irq"; - clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>; - clock-names = "mclk", "apb_pclk"; - bus-width = <8>; - max-frequency = <96000000>; - non-removable; - cap-sd-highspeed; - cap-mmc-highspeed; - mmc-ddr-1_8v; - vmmc-supply = <&vsdcc_fixed>; - dmas = <&sdcc1bam 2>, <&sdcc1bam 1>; - dma-names = "tx", "rx"; - }; - - sdcc3: mmc@12180000 { - compatible = "arm,pl18x", "arm,primecell"; - arm,primecell-periphid = <0x00051180>; - status = "disabled"; - reg = <0x12180000 0x2000>; - interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "cmd_irq"; - clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>; - clock-names = "mclk", "apb_pclk"; - bus-width = <8>; - cap-sd-highspeed; - cap-mmc-highspeed; - max-frequency = <192000000>; - sd-uhs-sdr104; - sd-uhs-ddr50; - vqmmc-supply = <&vsdcc_fixed>; - dmas = <&sdcc3bam 2>, <&sdcc3bam 1>; - dma-names = "tx", "rx"; - }; - }; - - sfpb_mutex: hwlock@1200600 { - compatible = "qcom,sfpb-mutex"; - reg = <0x01200600 0x100>; - - #hwlock-cells = <1>; - }; }; }; --2.36.1
Signature · 2 lines
With best wishes Dmitry
Quoted 2 lines · Christian Marangi
Reorganize node order and sort them by address.
So how to proceed with this? Should I send v2 with the changes pointed (stuff with no reg outside soc) or it's a NACK for the unnecessary changes?
I feel a bit stuck.
Quoted 882 lines
Signed-off-by Christian Marangi <[email protected]>---
This was picked from for-next qcom branch [1]. Reorganize dtsi as requested.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux.git/?h=for-next
arch/arm/boot/dts/qcom-ipq8064.dtsi | 766 ++++++++++++++-------------- 1 file changed, 383 insertions(+), 383 deletions(-)arch/arm/boot/dts/qcom-ipq8064.dtsi +383
-383@@ -332,19 +332,59 @@ soc: soc { ranges; compatible = "simple-bus"; - lpass@28100000 { - compatible = "qcom,lpass-cpu"; - status = "disabled"; - clocks = <&lcc AHBIX_CLK>, - <&lcc MI2S_OSR_CLK>, - <&lcc MI2S_BIT_CLK>; - clock-names = "ahbix-clk", - "mi2s-osr-clk", - "mi2s-bit-clk"; - interrupts = <GIC_SPI 85 IRQ_TYPE_EDGE_RISING>; - interrupt-names = "lpass-irq-lpaif"; - reg = <0x28100000 0x10000>; - reg-names = "lpass-lpaif"; + stmmac_axi_setup: stmmac-axi-config { + snps,wr_osr_lmt = <7>; + snps,rd_osr_lmt = <7>; + snps,blen = <16 0 0 0 0 0 0>; + }; + + vsdcc_fixed: vsdcc-regulator { + compatible = "regulator-fixed"; + regulator-name = "SDCC Power"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + rpm: rpm@108000 { + compatible = "qcom,rpm-ipq8064"; + reg = <0x108000 0x1000>; + qcom,ipc = <&l2cc 0x8 2>; + + interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "ack", "err", "wakeup"; + + clocks = <&gcc RPM_MSG_RAM_H_CLK>; + clock-names = "ram"; + + rpmcc: clock-controller { + compatible = "qcom,rpmcc-ipq806x", "qcom,rpmcc"; + #clock-cells = <1>; + }; + }; + + qcom,ssbi@500000 { + compatible = "qcom,ssbi"; + reg = <0x00500000 0x1000>; + qcom,controller-type = "pmic-arbiter"; + }; + + qfprom: qfprom@700000 { + compatible = "qcom,ipq8064-qfprom", "qcom,qfprom"; + reg = <0x00700000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + speedbin_efuse: speedbin@c0 { + reg = <0xc0 0x4>; + }; + tsens_calib: calib@400 { + reg = <0x400 0xb>; + }; + tsens_calib_backup: calib_backup@410 { + reg = <0x410 0xb>; + }; }; qcom_pinmux: pinmux@800000 {@@ -471,6 +511,35 @@ mux { }; }; + gcc: clock-controller@900000 { + compatible = "qcom,gcc-ipq8064", "syscon"; + clocks = <&pxo_board>, <&cxo_board>; + clock-names = "pxo", "cxo"; + reg = <0x00900000 0x4000>; + #clock-cells = <1>; + #reset-cells = <1>; + #power-domain-cells = <1>; + + tsens: thermal-sensor@900000 { + compatible = "qcom,ipq8064-tsens"; + + nvmem-cells = <&tsens_calib>, <&tsens_calib_backup>; + nvmem-cell-names = "calib", "calib_backup"; + interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "uplow"; + + #qcom,sensors = <11>; + #thermal-sensor-cells = <1>; + }; + }; + + sfpb_mutex: hwlock@1200600 { + compatible = "qcom,sfpb-mutex"; + reg = <0x01200600 0x100>; + + #hwlock-cells = <1>; + }; + intc: interrupt-controller@2000000 { compatible = "qcom,msm-qgic2"; interrupt-controller;@@ -500,46 +569,198 @@ IRQ_TYPE_EDGE_RISING)>, cpu-offset = <0x80000>; }; + l2cc: clock-controller@2011000 { + compatible = "qcom,kpss-gcc", "syscon"; + reg = <0x2011000 0x1000>; + clocks = <&gcc PLL8_VOTE>, <&pxo_board>; + clock-names = "pll8_vote", "pxo"; + clock-output-names = "acpu_l2_aux"; + }; + acc0: clock-controller@2088000 { compatible = "qcom,kpss-acc-v1"; reg = <0x02088000 0x1000>, <0x02008000 0x1000>; }; + saw0: regulator@2089000 { + compatible = "qcom,saw2"; + reg = <0x02089000 0x1000>, <0x02009000 0x1000>; + regulator; + }; + acc1: clock-controller@2098000 { compatible = "qcom,kpss-acc-v1"; reg = <0x02098000 0x1000>, <0x02008000 0x1000>; }; - adm_dma: dma-controller@18300000 { - compatible = "qcom,adm"; - reg = <0x18300000 0x100000>; - interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>; - #dma-cells = <1>; + saw1: regulator@2099000 { + compatible = "qcom,saw2"; + reg = <0x02099000 0x1000>, <0x02009000 0x1000>; + regulator; + }; - clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>; - clock-names = "core", "iface"; + nss_common: syscon@03000000 { + compatible = "syscon"; + reg = <0x03000000 0x0000FFFF>; + }; - resets = <&gcc ADM0_RESET>, - <&gcc ADM0_PBUS_RESET>, - <&gcc ADM0_C0_RESET>, - <&gcc ADM0_C1_RESET>, - <&gcc ADM0_C2_RESET>; - reset-names = "clk", "pbus", "c0", "c1", "c2"; - qcom,ee = <0>; + usb3_0: usb3@100f8800 { + compatible = "qcom,ipq8064-dwc3", "qcom,dwc3"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x100f8800 0x8000>; + clocks = <&gcc USB30_0_MASTER_CLK>; + clock-names = "core"; + + ranges; + + resets = <&gcc USB30_0_MASTER_RESET>; + reset-names = "master"; status = "disabled"; + + dwc3_0: dwc3@10000000 { + compatible = "snps,dwc3"; + reg = <0x10000000 0xcd00>; + interrupts = <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>; + phys = <&hs_phy_0>, <&ss_phy_0>; + phy-names = "usb2-phy", "usb3-phy"; + dr_mode = "host"; + snps,dis_u3_susphy_quirk; + }; }; - saw0: regulator@2089000 { - compatible = "qcom,saw2"; - reg = <0x02089000 0x1000>, <0x02009000 0x1000>; - regulator; + hs_phy_0: phy@100f8800 { + compatible = "qcom,ipq806x-usb-phy-hs"; + reg = <0x100f8800 0x30>; + clocks = <&gcc USB30_0_UTMI_CLK>; + clock-names = "ref"; + #phy-cells = <0>; + + status = "disabled"; }; - saw1: regulator@2099000 { - compatible = "qcom,saw2"; - reg = <0x02099000 0x1000>, <0x02009000 0x1000>; - regulator; + ss_phy_0: phy@100f8830 { + compatible = "qcom,ipq806x-usb-phy-ss"; + reg = <0x100f8830 0x30>; + clocks = <&gcc USB30_0_MASTER_CLK>; + clock-names = "ref"; + #phy-cells = <0>; + + status = "disabled"; + }; + + usb3_1: usb3@110f8800 { + compatible = "qcom,ipq8064-dwc3", "qcom,dwc3"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x110f8800 0x8000>; + clocks = <&gcc USB30_1_MASTER_CLK>; + clock-names = "core"; + + ranges; + + resets = <&gcc USB30_1_MASTER_RESET>; + reset-names = "master"; + + status = "disabled"; + + dwc3_1: dwc3@11000000 { + compatible = "snps,dwc3"; + reg = <0x11000000 0xcd00>; + interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; + phys = <&hs_phy_1>, <&ss_phy_1>; + phy-names = "usb2-phy", "usb3-phy"; + dr_mode = "host"; + snps,dis_u3_susphy_quirk; + }; + }; + + hs_phy_1: phy@110f8800 { + compatible = "qcom,ipq806x-usb-phy-hs"; + reg = <0x110f8800 0x30>; + clocks = <&gcc USB30_1_UTMI_CLK>; + clock-names = "ref"; + #phy-cells = <0>; + + status = "disabled"; + }; + + ss_phy_1: phy@110f8830 { + compatible = "qcom,ipq806x-usb-phy-ss"; + reg = <0x110f8830 0x30>; + clocks = <&gcc USB30_1_MASTER_CLK>; + clock-names = "ref"; + #phy-cells = <0>; + + status = "disabled"; + }; + + sdcc3bam: dma-controller@12182000 { + compatible = "qcom,bam-v1.3.0"; + reg = <0x12182000 0x8000>; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc SDC3_H_CLK>; + clock-names = "bam_clk"; + #dma-cells = <1>; + qcom,ee = <0>; + }; + + sdcc1bam: dma-controller@12402000 { + compatible = "qcom,bam-v1.3.0"; + reg = <0x12402000 0x8000>; + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc SDC1_H_CLK>; + clock-names = "bam_clk"; + #dma-cells = <1>; + qcom,ee = <0>; + }; + + amba: amba { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + sdcc3: mmc@12180000 { + compatible = "arm,pl18x", "arm,primecell"; + arm,primecell-periphid = <0x00051180>; + status = "disabled"; + reg = <0x12180000 0x2000>; + interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "cmd_irq"; + clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>; + clock-names = "mclk", "apb_pclk"; + bus-width = <8>; + cap-sd-highspeed; + cap-mmc-highspeed; + max-frequency = <192000000>; + sd-uhs-sdr104; + sd-uhs-ddr50; + vqmmc-supply = <&vsdcc_fixed>; + dmas = <&sdcc3bam 2>, <&sdcc3bam 1>; + dma-names = "tx", "rx"; + }; + + sdcc1: mmc@12400000 { + status = "disabled"; + compatible = "arm,pl18x", "arm,primecell"; + arm,primecell-periphid = <0x00051180>; + reg = <0x12400000 0x2000>; + interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "cmd_irq"; + clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>; + clock-names = "mclk", "apb_pclk"; + bus-width = <8>; + max-frequency = <96000000>; + non-removable; + cap-sd-highspeed; + cap-mmc-highspeed; + mmc-ddr-1_8v; + vmmc-supply = <&vsdcc_fixed>; + dmas = <&sdcc1bam 2>, <&sdcc1bam 1>; + dma-names = "tx", "rx"; + }; }; gsbi1: gsbi@12440000 {@@ -654,56 +875,6 @@ i2c@16380000 { }; }; - gsbi5: gsbi@1a200000 { - compatible = "qcom,gsbi-v1.0.0"; - cell-index = <5>; - reg = <0x1a200000 0x100>; - clocks = <&gcc GSBI5_H_CLK>; - clock-names = "iface"; - #address-cells = <1>; - #size-cells = <1>; - ranges; - status = "disabled"; - - syscon-tcsr = <&tcsr>; - - gsbi5_serial: serial@1a240000 { - compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; - reg = <0x1a240000 0x1000>, - <0x1a200000 0x1000>; - interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>; - clock-names = "core", "iface"; - status = "disabled"; - }; - - i2c@1a280000 { - compatible = "qcom,i2c-qup-v1.1.1"; - reg = <0x1a280000 0x1000>; - interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>; - - clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>; - clock-names = "core", "iface"; - status = "disabled"; - - #address-cells = <1>; - #size-cells = <0>; - }; - - spi@1a280000 { - compatible = "qcom,spi-qup-v1.1.1"; - reg = <0x1a280000 0x1000>; - interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>; - - clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>; - clock-names = "core", "iface"; - status = "disabled"; - - #address-cells = <1>; - #size-cells = <0>; - }; - }; - gsbi6: gsbi@16500000 { compatible = "qcom,gsbi-v1.0.0"; reg = <0x16500000 0x100>;@@ -784,149 +955,119 @@ gsbi7_i2c: i2c@16680000 { }; }; - rng@1a500000 { - compatible = "qcom,prng"; - reg = <0x1a500000 0x200>; - clocks = <&gcc PRNG_CLK>; - clock-names = "core"; - }; + adm_dma: dma-controller@18300000 { + compatible = "qcom,adm"; + reg = <0x18300000 0x100000>; + interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>; + #dma-cells = <1>; - sata_phy: sata-phy@1b400000 { - compatible = "qcom,ipq806x-sata-phy"; - reg = <0x1b400000 0x200>; + clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>; + clock-names = "core", "iface"; - clocks = <&gcc SATA_PHY_CFG_CLK>; - clock-names = "cfg"; + resets = <&gcc ADM0_RESET>, + <&gcc ADM0_PBUS_RESET>, + <&gcc ADM0_C0_RESET>, + <&gcc ADM0_C1_RESET>, + <&gcc ADM0_C2_RESET>; + reset-names = "clk", "pbus", "c0", "c1", "c2"; + qcom,ee = <0>; - #phy-cells = <0>; status = "disabled"; }; - nand: nand-controller@1ac00000 { - compatible = "qcom,ipq806x-nand"; - reg = <0x1ac00000 0x800>; - - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - - clocks = <&gcc EBI2_CLK>, - <&gcc EBI2_AON_CLK>; - clock-names = "core", "aon"; - - dmas = <&adm_dma 3>; - dma-names = "rxtx"; - qcom,cmd-crci = <15>; - qcom,data-crci = <3>; - + gsbi5: gsbi@1a200000 { + compatible = "qcom,gsbi-v1.0.0"; + cell-index = <5>; + reg = <0x1a200000 0x100>; + clocks = <&gcc GSBI5_H_CLK>; + clock-names = "iface"; #address-cells = <1>; - #size-cells = <0>; - + #size-cells = <1>; + ranges; status = "disabled"; - }; - sata: sata@29000000 { - compatible = "qcom,ipq806x-ahci", "generic-ahci"; - reg = <0x29000000 0x180>; + syscon-tcsr = <&tcsr>; - interrupts = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>; + gsbi5_serial: serial@1a240000 { + compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; + reg = <0x1a240000 0x1000>, + <0x1a200000 0x1000>; + interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>; + clock-names = "core", "iface"; + status = "disabled"; + }; - clocks = <&gcc SFAB_SATA_S_H_CLK>, - <&gcc SATA_H_CLK>, - <&gcc SATA_A_CLK>, - <&gcc SATA_RXOOB_CLK>, - <&gcc SATA_PMALIVE_CLK>; - clock-names = "slave_face", "iface", "core", - "rxoob", "pmalive"; + i2c@1a280000 { + compatible = "qcom,i2c-qup-v1.1.1"; + reg = <0x1a280000 0x1000>; + interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>; - assigned-clocks = <&gcc SATA_RXOOB_CLK>, <&gcc SATA_PMALIVE_CLK>; - assigned-clock-rates = <100000000>, <100000000>; + clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>; + clock-names = "core", "iface"; + status = "disabled"; - phys = <&sata_phy>; - phy-names = "sata-phy"; - status = "disabled"; - }; + #address-cells = <1>; + #size-cells = <0>; + }; - qcom,ssbi@500000 { - compatible = "qcom,ssbi"; - reg = <0x00500000 0x1000>; - qcom,controller-type = "pmic-arbiter"; - }; + spi@1a280000 { + compatible = "qcom,spi-qup-v1.1.1"; + reg = <0x1a280000 0x1000>; + interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>; - qfprom: qfprom@700000 { - compatible = "qcom,ipq8064-qfprom", "qcom,qfprom"; - reg = <0x00700000 0x1000>; - #address-cells = <1>; - #size-cells = <1>; - speedbin_efuse: speedbin@c0 { - reg = <0xc0 0x4>; - }; - tsens_calib: calib@400 { - reg = <0x400 0xb>; - }; - tsens_calib_backup: calib_backup@410 { - reg = <0x410 0xb>; + clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>; + clock-names = "core", "iface"; + status = "disabled"; + + #address-cells = <1>; + #size-cells = <0>; }; }; - gcc: clock-controller@900000 { - compatible = "qcom,gcc-ipq8064", "syscon"; - clocks = <&pxo_board>, <&cxo_board>; - clock-names = "pxo", "cxo"; - reg = <0x00900000 0x4000>; - #clock-cells = <1>; - #reset-cells = <1>; - #power-domain-cells = <1>; - - tsens: thermal-sensor@900000 { - compatible = "qcom,ipq8064-tsens"; - - nvmem-cells = <&tsens_calib>, <&tsens_calib_backup>; - nvmem-cell-names = "calib", "calib_backup"; - interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "uplow"; + tcsr: syscon@1a400000 { + compatible = "qcom,tcsr-ipq8064", "syscon"; + reg = <0x1a400000 0x100>; + }; - #qcom,sensors = <11>; - #thermal-sensor-cells = <1>; - }; + rng@1a500000 { + compatible = "qcom,prng"; + reg = <0x1a500000 0x200>; + clocks = <&gcc PRNG_CLK>; + clock-names = "core"; }; - rpm: rpm@108000 { - compatible = "qcom,rpm-ipq8064"; - reg = <0x108000 0x1000>; - qcom,ipc = <&l2cc 0x8 2>; + nand: nand-controller@1ac00000 { + compatible = "qcom,ipq806x-nand"; + reg = <0x1ac00000 0x800>; - interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "ack", "err", "wakeup"; + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; - clocks = <&gcc RPM_MSG_RAM_H_CLK>; - clock-names = "ram"; + clocks = <&gcc EBI2_CLK>, + <&gcc EBI2_AON_CLK>; + clock-names = "core", "aon"; + + dmas = <&adm_dma 3>; + dma-names = "rxtx"; + qcom,cmd-crci = <15>; + qcom,data-crci = <3>; - rpmcc: clock-controller { - compatible = "qcom,rpmcc-ipq806x", "qcom,rpmcc"; - #clock-cells = <1>; - }; - }; + #address-cells = <1>; + #size-cells = <0>; - tcsr: syscon@1a400000 { - compatible = "qcom,tcsr-ipq8064", "syscon"; - reg = <0x1a400000 0x100>; + status = "disabled"; }; - l2cc: clock-controller@2011000 { - compatible = "qcom,kpss-gcc", "syscon"; - reg = <0x2011000 0x1000>; - clocks = <&gcc PLL8_VOTE>, <&pxo_board>; - clock-names = "pll8_vote", "pxo"; - clock-output-names = "acpu_l2_aux"; - }; + sata_phy: sata-phy@1b400000 { + compatible = "qcom,ipq806x-sata-phy"; + reg = <0x1b400000 0x200>; - lcc: clock-controller@28000000 { - compatible = "qcom,lcc-ipq8064"; - reg = <0x28000000 0x1000>; - #clock-cells = <1>; - #reset-cells = <1>; + clocks = <&gcc SATA_PHY_CFG_CLK>; + clock-names = "cfg"; + + #phy-cells = <0>; + status = "disabled"; }; pcie0: pci@1b500000 {@@ -1082,20 +1223,53 @@ pcie2: pci@1b900000 { perst-gpio = <&qcom_pinmux 63 GPIO_ACTIVE_LOW>; }; - nss_common: syscon@03000000 { - compatible = "syscon"; - reg = <0x03000000 0x0000FFFF>; - }; - qsgmii_csr: syscon@1bb00000 { compatible = "syscon"; reg = <0x1bb00000 0x000001FF>; }; - stmmac_axi_setup: stmmac-axi-config { - snps,wr_osr_lmt = <7>; - snps,rd_osr_lmt = <7>; - snps,blen = <16 0 0 0 0 0 0>; + lcc: clock-controller@28000000 { + compatible = "qcom,lcc-ipq8064"; + reg = <0x28000000 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + lpass@28100000 { + compatible = "qcom,lpass-cpu"; + status = "disabled"; + clocks = <&lcc AHBIX_CLK>, + <&lcc MI2S_OSR_CLK>, + <&lcc MI2S_BIT_CLK>; + clock-names = "ahbix-clk", + "mi2s-osr-clk", + "mi2s-bit-clk"; + interrupts = <GIC_SPI 85 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "lpass-irq-lpaif"; + reg = <0x28100000 0x10000>; + reg-names = "lpass-lpaif"; + }; + + sata: sata@29000000 { + compatible = "qcom,ipq806x-ahci", "generic-ahci"; + reg = <0x29000000 0x180>; + + interrupts = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc SFAB_SATA_S_H_CLK>, + <&gcc SATA_H_CLK>, + <&gcc SATA_A_CLK>, + <&gcc SATA_RXOOB_CLK>, + <&gcc SATA_PMALIVE_CLK>; + clock-names = "slave_face", "iface", "core", + "rxoob", "pmalive"; + + assigned-clocks = <&gcc SATA_RXOOB_CLK>, <&gcc SATA_PMALIVE_CLK>; + assigned-clock-rates = <100000000>, <100000000>; + + phys = <&sata_phy>; + phy-names = "sata-phy"; + status = "disabled"; }; gmac0: ethernet@37000000 {@@ -1193,179 +1367,5 @@ gmac3: ethernet@37600000 { status = "disabled"; }; - - hs_phy_0: phy@100f8800 { - compatible = "qcom,ipq806x-usb-phy-hs"; - reg = <0x100f8800 0x30>; - clocks = <&gcc USB30_0_UTMI_CLK>; - clock-names = "ref"; - #phy-cells = <0>; - - status = "disabled"; - }; - - ss_phy_0: phy@100f8830 { - compatible = "qcom,ipq806x-usb-phy-ss"; - reg = <0x100f8830 0x30>; - clocks = <&gcc USB30_0_MASTER_CLK>; - clock-names = "ref"; - #phy-cells = <0>; - - status = "disabled"; - }; - - usb3_0: usb3@100f8800 { - compatible = "qcom,ipq8064-dwc3", "qcom,dwc3"; - #address-cells = <1>; - #size-cells = <1>; - reg = <0x100f8800 0x8000>; - clocks = <&gcc USB30_0_MASTER_CLK>; - clock-names = "core"; - - ranges; - - resets = <&gcc USB30_0_MASTER_RESET>; - reset-names = "master"; - - status = "disabled"; - - dwc3_0: dwc3@10000000 { - compatible = "snps,dwc3"; - reg = <0x10000000 0xcd00>; - interrupts = <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>; - phys = <&hs_phy_0>, <&ss_phy_0>; - phy-names = "usb2-phy", "usb3-phy"; - dr_mode = "host"; - snps,dis_u3_susphy_quirk; - }; - }; - - hs_phy_1: phy@110f8800 { - compatible = "qcom,ipq806x-usb-phy-hs"; - reg = <0x110f8800 0x30>; - clocks = <&gcc USB30_1_UTMI_CLK>; - clock-names = "ref"; - #phy-cells = <0>; - - status = "disabled"; - }; - - ss_phy_1: phy@110f8830 { - compatible = "qcom,ipq806x-usb-phy-ss"; - reg = <0x110f8830 0x30>; - clocks = <&gcc USB30_1_MASTER_CLK>; - clock-names = "ref"; - #phy-cells = <0>; - - status = "disabled"; - }; - - usb3_1: usb3@110f8800 { - compatible = "qcom,ipq8064-dwc3", "qcom,dwc3"; - #address-cells = <1>; - #size-cells = <1>; - reg = <0x110f8800 0x8000>; - clocks = <&gcc USB30_1_MASTER_CLK>; - clock-names = "core"; - - ranges; - - resets = <&gcc USB30_1_MASTER_RESET>; - reset-names = "master"; - - status = "disabled"; - - dwc3_1: dwc3@11000000 { - compatible = "snps,dwc3"; - reg = <0x11000000 0xcd00>; - interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; - phys = <&hs_phy_1>, <&ss_phy_1>; - phy-names = "usb2-phy", "usb3-phy"; - dr_mode = "host"; - snps,dis_u3_susphy_quirk; - }; - }; - - vsdcc_fixed: vsdcc-regulator { - compatible = "regulator-fixed"; - regulator-name = "SDCC Power"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - }; - - sdcc1bam: dma-controller@12402000 { - compatible = "qcom,bam-v1.3.0"; - reg = <0x12402000 0x8000>; - interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&gcc SDC1_H_CLK>; - clock-names = "bam_clk"; - #dma-cells = <1>; - qcom,ee = <0>; - }; - - sdcc3bam: dma-controller@12182000 { - compatible = "qcom,bam-v1.3.0"; - reg = <0x12182000 0x8000>; - interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&gcc SDC3_H_CLK>; - clock-names = "bam_clk"; - #dma-cells = <1>; - qcom,ee = <0>; - }; - - amba: amba { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <1>; - ranges; - - sdcc1: mmc@12400000 { - status = "disabled"; - compatible = "arm,pl18x", "arm,primecell"; - arm,primecell-periphid = <0x00051180>; - reg = <0x12400000 0x2000>; - interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "cmd_irq"; - clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>; - clock-names = "mclk", "apb_pclk"; - bus-width = <8>; - max-frequency = <96000000>; - non-removable; - cap-sd-highspeed; - cap-mmc-highspeed; - mmc-ddr-1_8v; - vmmc-supply = <&vsdcc_fixed>; - dmas = <&sdcc1bam 2>, <&sdcc1bam 1>; - dma-names = "tx", "rx"; - }; - - sdcc3: mmc@12180000 { - compatible = "arm,pl18x", "arm,primecell"; - arm,primecell-periphid = <0x00051180>; - status = "disabled"; - reg = <0x12180000 0x2000>; - interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "cmd_irq"; - clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>; - clock-names = "mclk", "apb_pclk"; - bus-width = <8>; - cap-sd-highspeed; - cap-mmc-highspeed; - max-frequency = <192000000>; - sd-uhs-sdr104; - sd-uhs-ddr50; - vqmmc-supply = <&vsdcc_fixed>; - dmas = <&sdcc3bam 2>, <&sdcc3bam 1>; - dma-names = "tx", "rx"; - }; - }; - - sfpb_mutex: hwlock@1200600 { - compatible = "qcom,sfpb-mutex"; - reg = <0x01200600 0x100>; - - #hwlock-cells = <1>; - }; }; };Signature · 1 line
2.36.1
Signature · 1 line
Ansuel
Quoted 10 lines · Christian Marangi
Quoted 2 lines · Christian Marangi
Reorganize node order and sort them by address.
So how to proceed with this? Should I send v2 with the changes pointed (stuff with no reg outside soc) or it's a NACK for the unnecessary changes?
I feel a bit stuck.
Afaict the pieces pointed out existed before the shuffle as well, so I've merged the two patches. Please submit additional cleanups on top.
Thank you,
Bjorn
Quoted 885 lines
Quoted 882 lines
Signed-off-by Christian Marangi <[email protected]>---
This was picked from for-next qcom branch [1]. Reorganize dtsi as requested.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux.git/?h=for-next
arch/arm/boot/dts/qcom-ipq8064.dtsi | 766 ++++++++++++++-------------- 1 file changed, 383 insertions(+), 383 deletions(-)arch/arm/boot/dts/qcom-ipq8064.dtsi +383
-383@@ -332,19 +332,59 @@ soc: soc { ranges; compatible = "simple-bus"; - lpass@28100000 { - compatible = "qcom,lpass-cpu"; - status = "disabled"; - clocks = <&lcc AHBIX_CLK>, - <&lcc MI2S_OSR_CLK>, - <&lcc MI2S_BIT_CLK>; - clock-names = "ahbix-clk", - "mi2s-osr-clk", - "mi2s-bit-clk"; - interrupts = <GIC_SPI 85 IRQ_TYPE_EDGE_RISING>; - interrupt-names = "lpass-irq-lpaif"; - reg = <0x28100000 0x10000>; - reg-names = "lpass-lpaif"; + stmmac_axi_setup: stmmac-axi-config { + snps,wr_osr_lmt = <7>; + snps,rd_osr_lmt = <7>; + snps,blen = <16 0 0 0 0 0 0>; + }; + + vsdcc_fixed: vsdcc-regulator { + compatible = "regulator-fixed"; + regulator-name = "SDCC Power"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + rpm: rpm@108000 { + compatible = "qcom,rpm-ipq8064"; + reg = <0x108000 0x1000>; + qcom,ipc = <&l2cc 0x8 2>; + + interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "ack", "err", "wakeup"; + + clocks = <&gcc RPM_MSG_RAM_H_CLK>; + clock-names = "ram"; + + rpmcc: clock-controller { + compatible = "qcom,rpmcc-ipq806x", "qcom,rpmcc"; + #clock-cells = <1>; + }; + }; + + qcom,ssbi@500000 { + compatible = "qcom,ssbi"; + reg = <0x00500000 0x1000>; + qcom,controller-type = "pmic-arbiter"; + }; + + qfprom: qfprom@700000 { + compatible = "qcom,ipq8064-qfprom", "qcom,qfprom"; + reg = <0x00700000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + speedbin_efuse: speedbin@c0 { + reg = <0xc0 0x4>; + }; + tsens_calib: calib@400 { + reg = <0x400 0xb>; + }; + tsens_calib_backup: calib_backup@410 { + reg = <0x410 0xb>; + }; }; qcom_pinmux: pinmux@800000 {@@ -471,6 +511,35 @@ mux { }; }; + gcc: clock-controller@900000 { + compatible = "qcom,gcc-ipq8064", "syscon"; + clocks = <&pxo_board>, <&cxo_board>; + clock-names = "pxo", "cxo"; + reg = <0x00900000 0x4000>; + #clock-cells = <1>; + #reset-cells = <1>; + #power-domain-cells = <1>; + + tsens: thermal-sensor@900000 { + compatible = "qcom,ipq8064-tsens"; + + nvmem-cells = <&tsens_calib>, <&tsens_calib_backup>; + nvmem-cell-names = "calib", "calib_backup"; + interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "uplow"; + + #qcom,sensors = <11>; + #thermal-sensor-cells = <1>; + }; + }; + + sfpb_mutex: hwlock@1200600 { + compatible = "qcom,sfpb-mutex"; + reg = <0x01200600 0x100>; + + #hwlock-cells = <1>; + }; + intc: interrupt-controller@2000000 { compatible = "qcom,msm-qgic2"; interrupt-controller;@@ -500,46 +569,198 @@ IRQ_TYPE_EDGE_RISING)>, cpu-offset = <0x80000>; }; + l2cc: clock-controller@2011000 { + compatible = "qcom,kpss-gcc", "syscon"; + reg = <0x2011000 0x1000>; + clocks = <&gcc PLL8_VOTE>, <&pxo_board>; + clock-names = "pll8_vote", "pxo"; + clock-output-names = "acpu_l2_aux"; + }; + acc0: clock-controller@2088000 { compatible = "qcom,kpss-acc-v1"; reg = <0x02088000 0x1000>, <0x02008000 0x1000>; }; + saw0: regulator@2089000 { + compatible = "qcom,saw2"; + reg = <0x02089000 0x1000>, <0x02009000 0x1000>; + regulator; + }; + acc1: clock-controller@2098000 { compatible = "qcom,kpss-acc-v1"; reg = <0x02098000 0x1000>, <0x02008000 0x1000>; }; - adm_dma: dma-controller@18300000 { - compatible = "qcom,adm"; - reg = <0x18300000 0x100000>; - interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>; - #dma-cells = <1>; + saw1: regulator@2099000 { + compatible = "qcom,saw2"; + reg = <0x02099000 0x1000>, <0x02009000 0x1000>; + regulator; + }; - clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>; - clock-names = "core", "iface"; + nss_common: syscon@03000000 { + compatible = "syscon"; + reg = <0x03000000 0x0000FFFF>; + }; - resets = <&gcc ADM0_RESET>, - <&gcc ADM0_PBUS_RESET>, - <&gcc ADM0_C0_RESET>, - <&gcc ADM0_C1_RESET>, - <&gcc ADM0_C2_RESET>; - reset-names = "clk", "pbus", "c0", "c1", "c2"; - qcom,ee = <0>; + usb3_0: usb3@100f8800 { + compatible = "qcom,ipq8064-dwc3", "qcom,dwc3"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x100f8800 0x8000>; + clocks = <&gcc USB30_0_MASTER_CLK>; + clock-names = "core"; + + ranges; + + resets = <&gcc USB30_0_MASTER_RESET>; + reset-names = "master"; status = "disabled"; + + dwc3_0: dwc3@10000000 { + compatible = "snps,dwc3"; + reg = <0x10000000 0xcd00>; + interrupts = <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>; + phys = <&hs_phy_0>, <&ss_phy_0>; + phy-names = "usb2-phy", "usb3-phy"; + dr_mode = "host"; + snps,dis_u3_susphy_quirk; + }; }; - saw0: regulator@2089000 { - compatible = "qcom,saw2"; - reg = <0x02089000 0x1000>, <0x02009000 0x1000>; - regulator; + hs_phy_0: phy@100f8800 { + compatible = "qcom,ipq806x-usb-phy-hs"; + reg = <0x100f8800 0x30>; + clocks = <&gcc USB30_0_UTMI_CLK>; + clock-names = "ref"; + #phy-cells = <0>; + + status = "disabled"; }; - saw1: regulator@2099000 { - compatible = "qcom,saw2"; - reg = <0x02099000 0x1000>, <0x02009000 0x1000>; - regulator; + ss_phy_0: phy@100f8830 { + compatible = "qcom,ipq806x-usb-phy-ss"; + reg = <0x100f8830 0x30>; + clocks = <&gcc USB30_0_MASTER_CLK>; + clock-names = "ref"; + #phy-cells = <0>; + + status = "disabled"; + }; + + usb3_1: usb3@110f8800 { + compatible = "qcom,ipq8064-dwc3", "qcom,dwc3"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x110f8800 0x8000>; + clocks = <&gcc USB30_1_MASTER_CLK>; + clock-names = "core"; + + ranges; + + resets = <&gcc USB30_1_MASTER_RESET>; + reset-names = "master"; + + status = "disabled"; + + dwc3_1: dwc3@11000000 { + compatible = "snps,dwc3"; + reg = <0x11000000 0xcd00>; + interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; + phys = <&hs_phy_1>, <&ss_phy_1>; + phy-names = "usb2-phy", "usb3-phy"; + dr_mode = "host"; + snps,dis_u3_susphy_quirk; + }; + }; + + hs_phy_1: phy@110f8800 { + compatible = "qcom,ipq806x-usb-phy-hs"; + reg = <0x110f8800 0x30>; + clocks = <&gcc USB30_1_UTMI_CLK>; + clock-names = "ref"; + #phy-cells = <0>; + + status = "disabled"; + }; + + ss_phy_1: phy@110f8830 { + compatible = "qcom,ipq806x-usb-phy-ss"; + reg = <0x110f8830 0x30>; + clocks = <&gcc USB30_1_MASTER_CLK>; + clock-names = "ref"; + #phy-cells = <0>; + + status = "disabled"; + }; + + sdcc3bam: dma-controller@12182000 { + compatible = "qcom,bam-v1.3.0"; + reg = <0x12182000 0x8000>; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc SDC3_H_CLK>; + clock-names = "bam_clk"; + #dma-cells = <1>; + qcom,ee = <0>; + }; + + sdcc1bam: dma-controller@12402000 { + compatible = "qcom,bam-v1.3.0"; + reg = <0x12402000 0x8000>; + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc SDC1_H_CLK>; + clock-names = "bam_clk"; + #dma-cells = <1>; + qcom,ee = <0>; + }; + + amba: amba { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + sdcc3: mmc@12180000 { + compatible = "arm,pl18x", "arm,primecell"; + arm,primecell-periphid = <0x00051180>; + status = "disabled"; + reg = <0x12180000 0x2000>; + interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "cmd_irq"; + clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>; + clock-names = "mclk", "apb_pclk"; + bus-width = <8>; + cap-sd-highspeed; + cap-mmc-highspeed; + max-frequency = <192000000>; + sd-uhs-sdr104; + sd-uhs-ddr50; + vqmmc-supply = <&vsdcc_fixed>; + dmas = <&sdcc3bam 2>, <&sdcc3bam 1>; + dma-names = "tx", "rx"; + }; + + sdcc1: mmc@12400000 { + status = "disabled"; + compatible = "arm,pl18x", "arm,primecell"; + arm,primecell-periphid = <0x00051180>; + reg = <0x12400000 0x2000>; + interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "cmd_irq"; + clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>; + clock-names = "mclk", "apb_pclk"; + bus-width = <8>; + max-frequency = <96000000>; + non-removable; + cap-sd-highspeed; + cap-mmc-highspeed; + mmc-ddr-1_8v; + vmmc-supply = <&vsdcc_fixed>; + dmas = <&sdcc1bam 2>, <&sdcc1bam 1>; + dma-names = "tx", "rx"; + }; }; gsbi1: gsbi@12440000 {@@ -654,56 +875,6 @@ i2c@16380000 { }; }; - gsbi5: gsbi@1a200000 { - compatible = "qcom,gsbi-v1.0.0"; - cell-index = <5>; - reg = <0x1a200000 0x100>; - clocks = <&gcc GSBI5_H_CLK>; - clock-names = "iface"; - #address-cells = <1>; - #size-cells = <1>; - ranges; - status = "disabled"; - - syscon-tcsr = <&tcsr>; - - gsbi5_serial: serial@1a240000 { - compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; - reg = <0x1a240000 0x1000>, - <0x1a200000 0x1000>; - interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>; - clock-names = "core", "iface"; - status = "disabled"; - }; - - i2c@1a280000 { - compatible = "qcom,i2c-qup-v1.1.1"; - reg = <0x1a280000 0x1000>; - interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>; - - clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>; - clock-names = "core", "iface"; - status = "disabled"; - - #address-cells = <1>; - #size-cells = <0>; - }; - - spi@1a280000 { - compatible = "qcom,spi-qup-v1.1.1"; - reg = <0x1a280000 0x1000>; - interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>; - - clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>; - clock-names = "core", "iface"; - status = "disabled"; - - #address-cells = <1>; - #size-cells = <0>; - }; - }; - gsbi6: gsbi@16500000 { compatible = "qcom,gsbi-v1.0.0"; reg = <0x16500000 0x100>;@@ -784,149 +955,119 @@ gsbi7_i2c: i2c@16680000 { }; }; - rng@1a500000 { - compatible = "qcom,prng"; - reg = <0x1a500000 0x200>; - clocks = <&gcc PRNG_CLK>; - clock-names = "core"; - }; + adm_dma: dma-controller@18300000 { + compatible = "qcom,adm"; + reg = <0x18300000 0x100000>; + interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>; + #dma-cells = <1>; - sata_phy: sata-phy@1b400000 { - compatible = "qcom,ipq806x-sata-phy"; - reg = <0x1b400000 0x200>; + clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>; + clock-names = "core", "iface"; - clocks = <&gcc SATA_PHY_CFG_CLK>; - clock-names = "cfg"; + resets = <&gcc ADM0_RESET>, + <&gcc ADM0_PBUS_RESET>, + <&gcc ADM0_C0_RESET>, + <&gcc ADM0_C1_RESET>, + <&gcc ADM0_C2_RESET>; + reset-names = "clk", "pbus", "c0", "c1", "c2"; + qcom,ee = <0>; - #phy-cells = <0>; status = "disabled"; }; - nand: nand-controller@1ac00000 { - compatible = "qcom,ipq806x-nand"; - reg = <0x1ac00000 0x800>; - - pinctrl-0 = <&nand_pins>; - pinctrl-names = "default"; - - clocks = <&gcc EBI2_CLK>, - <&gcc EBI2_AON_CLK>; - clock-names = "core", "aon"; - - dmas = <&adm_dma 3>; - dma-names = "rxtx"; - qcom,cmd-crci = <15>; - qcom,data-crci = <3>; - + gsbi5: gsbi@1a200000 { + compatible = "qcom,gsbi-v1.0.0"; + cell-index = <5>; + reg = <0x1a200000 0x100>; + clocks = <&gcc GSBI5_H_CLK>; + clock-names = "iface"; #address-cells = <1>; - #size-cells = <0>; - + #size-cells = <1>; + ranges; status = "disabled"; - }; - sata: sata@29000000 { - compatible = "qcom,ipq806x-ahci", "generic-ahci"; - reg = <0x29000000 0x180>; + syscon-tcsr = <&tcsr>; - interrupts = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>; + gsbi5_serial: serial@1a240000 { + compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; + reg = <0x1a240000 0x1000>, + <0x1a200000 0x1000>; + interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>; + clock-names = "core", "iface"; + status = "disabled"; + }; - clocks = <&gcc SFAB_SATA_S_H_CLK>, - <&gcc SATA_H_CLK>, - <&gcc SATA_A_CLK>, - <&gcc SATA_RXOOB_CLK>, - <&gcc SATA_PMALIVE_CLK>; - clock-names = "slave_face", "iface", "core", - "rxoob", "pmalive"; + i2c@1a280000 { + compatible = "qcom,i2c-qup-v1.1.1"; + reg = <0x1a280000 0x1000>; + interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>; - assigned-clocks = <&gcc SATA_RXOOB_CLK>, <&gcc SATA_PMALIVE_CLK>; - assigned-clock-rates = <100000000>, <100000000>; + clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>; + clock-names = "core", "iface"; + status = "disabled"; - phys = <&sata_phy>; - phy-names = "sata-phy"; - status = "disabled"; - }; + #address-cells = <1>; + #size-cells = <0>; + }; - qcom,ssbi@500000 { - compatible = "qcom,ssbi"; - reg = <0x00500000 0x1000>; - qcom,controller-type = "pmic-arbiter"; - }; + spi@1a280000 { + compatible = "qcom,spi-qup-v1.1.1"; + reg = <0x1a280000 0x1000>; + interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>; - qfprom: qfprom@700000 { - compatible = "qcom,ipq8064-qfprom", "qcom,qfprom"; - reg = <0x00700000 0x1000>; - #address-cells = <1>; - #size-cells = <1>; - speedbin_efuse: speedbin@c0 { - reg = <0xc0 0x4>; - }; - tsens_calib: calib@400 { - reg = <0x400 0xb>; - }; - tsens_calib_backup: calib_backup@410 { - reg = <0x410 0xb>; + clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>; + clock-names = "core", "iface"; + status = "disabled"; + + #address-cells = <1>; + #size-cells = <0>; }; }; - gcc: clock-controller@900000 { - compatible = "qcom,gcc-ipq8064", "syscon"; - clocks = <&pxo_board>, <&cxo_board>; - clock-names = "pxo", "cxo"; - reg = <0x00900000 0x4000>; - #clock-cells = <1>; - #reset-cells = <1>; - #power-domain-cells = <1>; - - tsens: thermal-sensor@900000 { - compatible = "qcom,ipq8064-tsens"; - - nvmem-cells = <&tsens_calib>, <&tsens_calib_backup>; - nvmem-cell-names = "calib", "calib_backup"; - interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "uplow"; + tcsr: syscon@1a400000 { + compatible = "qcom,tcsr-ipq8064", "syscon"; + reg = <0x1a400000 0x100>; + }; - #qcom,sensors = <11>; - #thermal-sensor-cells = <1>; - }; + rng@1a500000 { + compatible = "qcom,prng"; + reg = <0x1a500000 0x200>; + clocks = <&gcc PRNG_CLK>; + clock-names = "core"; }; - rpm: rpm@108000 { - compatible = "qcom,rpm-ipq8064"; - reg = <0x108000 0x1000>; - qcom,ipc = <&l2cc 0x8 2>; + nand: nand-controller@1ac00000 { + compatible = "qcom,ipq806x-nand"; + reg = <0x1ac00000 0x800>; - interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "ack", "err", "wakeup"; + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; - clocks = <&gcc RPM_MSG_RAM_H_CLK>; - clock-names = "ram"; + clocks = <&gcc EBI2_CLK>, + <&gcc EBI2_AON_CLK>; + clock-names = "core", "aon"; + + dmas = <&adm_dma 3>; + dma-names = "rxtx"; + qcom,cmd-crci = <15>; + qcom,data-crci = <3>; - rpmcc: clock-controller { - compatible = "qcom,rpmcc-ipq806x", "qcom,rpmcc"; - #clock-cells = <1>; - }; - }; + #address-cells = <1>; + #size-cells = <0>; - tcsr: syscon@1a400000 { - compatible = "qcom,tcsr-ipq8064", "syscon"; - reg = <0x1a400000 0x100>; + status = "disabled"; }; - l2cc: clock-controller@2011000 { - compatible = "qcom,kpss-gcc", "syscon"; - reg = <0x2011000 0x1000>; - clocks = <&gcc PLL8_VOTE>, <&pxo_board>; - clock-names = "pll8_vote", "pxo"; - clock-output-names = "acpu_l2_aux"; - }; + sata_phy: sata-phy@1b400000 { + compatible = "qcom,ipq806x-sata-phy"; + reg = <0x1b400000 0x200>; - lcc: clock-controller@28000000 { - compatible = "qcom,lcc-ipq8064"; - reg = <0x28000000 0x1000>; - #clock-cells = <1>; - #reset-cells = <1>; + clocks = <&gcc SATA_PHY_CFG_CLK>; + clock-names = "cfg"; + + #phy-cells = <0>; + status = "disabled"; }; pcie0: pci@1b500000 {@@ -1082,20 +1223,53 @@ pcie2: pci@1b900000 { perst-gpio = <&qcom_pinmux 63 GPIO_ACTIVE_LOW>; }; - nss_common: syscon@03000000 { - compatible = "syscon"; - reg = <0x03000000 0x0000FFFF>; - }; - qsgmii_csr: syscon@1bb00000 { compatible = "syscon"; reg = <0x1bb00000 0x000001FF>; }; - stmmac_axi_setup: stmmac-axi-config { - snps,wr_osr_lmt = <7>; - snps,rd_osr_lmt = <7>; - snps,blen = <16 0 0 0 0 0 0>; + lcc: clock-controller@28000000 { + compatible = "qcom,lcc-ipq8064"; + reg = <0x28000000 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + lpass@28100000 { + compatible = "qcom,lpass-cpu"; + status = "disabled"; + clocks = <&lcc AHBIX_CLK>, + <&lcc MI2S_OSR_CLK>, + <&lcc MI2S_BIT_CLK>; + clock-names = "ahbix-clk", + "mi2s-osr-clk", + "mi2s-bit-clk"; + interrupts = <GIC_SPI 85 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "lpass-irq-lpaif"; + reg = <0x28100000 0x10000>; + reg-names = "lpass-lpaif"; + }; + + sata: sata@29000000 { + compatible = "qcom,ipq806x-ahci", "generic-ahci"; + reg = <0x29000000 0x180>; + + interrupts = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc SFAB_SATA_S_H_CLK>, + <&gcc SATA_H_CLK>, + <&gcc SATA_A_CLK>, + <&gcc SATA_RXOOB_CLK>, + <&gcc SATA_PMALIVE_CLK>; + clock-names = "slave_face", "iface", "core", + "rxoob", "pmalive"; + + assigned-clocks = <&gcc SATA_RXOOB_CLK>, <&gcc SATA_PMALIVE_CLK>; + assigned-clock-rates = <100000000>, <100000000>; + + phys = <&sata_phy>; + phy-names = "sata-phy"; + status = "disabled"; }; gmac0: ethernet@37000000 {@@ -1193,179 +1367,5 @@ gmac3: ethernet@37600000 { status = "disabled"; }; - - hs_phy_0: phy@100f8800 { - compatible = "qcom,ipq806x-usb-phy-hs"; - reg = <0x100f8800 0x30>; - clocks = <&gcc USB30_0_UTMI_CLK>; - clock-names = "ref"; - #phy-cells = <0>; - - status = "disabled"; - }; - - ss_phy_0: phy@100f8830 { - compatible = "qcom,ipq806x-usb-phy-ss"; - reg = <0x100f8830 0x30>; - clocks = <&gcc USB30_0_MASTER_CLK>; - clock-names = "ref"; - #phy-cells = <0>; - - status = "disabled"; - }; - - usb3_0: usb3@100f8800 { - compatible = "qcom,ipq8064-dwc3", "qcom,dwc3"; - #address-cells = <1>; - #size-cells = <1>; - reg = <0x100f8800 0x8000>; - clocks = <&gcc USB30_0_MASTER_CLK>; - clock-names = "core"; - - ranges; - - resets = <&gcc USB30_0_MASTER_RESET>; - reset-names = "master"; - - status = "disabled"; - - dwc3_0: dwc3@10000000 { - compatible = "snps,dwc3"; - reg = <0x10000000 0xcd00>; - interrupts = <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>; - phys = <&hs_phy_0>, <&ss_phy_0>; - phy-names = "usb2-phy", "usb3-phy"; - dr_mode = "host"; - snps,dis_u3_susphy_quirk; - }; - }; - - hs_phy_1: phy@110f8800 { - compatible = "qcom,ipq806x-usb-phy-hs"; - reg = <0x110f8800 0x30>; - clocks = <&gcc USB30_1_UTMI_CLK>; - clock-names = "ref"; - #phy-cells = <0>; - - status = "disabled"; - }; - - ss_phy_1: phy@110f8830 { - compatible = "qcom,ipq806x-usb-phy-ss"; - reg = <0x110f8830 0x30>; - clocks = <&gcc USB30_1_MASTER_CLK>; - clock-names = "ref"; - #phy-cells = <0>; - - status = "disabled"; - }; - - usb3_1: usb3@110f8800 { - compatible = "qcom,ipq8064-dwc3", "qcom,dwc3"; - #address-cells = <1>; - #size-cells = <1>; - reg = <0x110f8800 0x8000>; - clocks = <&gcc USB30_1_MASTER_CLK>; - clock-names = "core"; - - ranges; - - resets = <&gcc USB30_1_MASTER_RESET>; - reset-names = "master"; - - status = "disabled"; - - dwc3_1: dwc3@11000000 { - compatible = "snps,dwc3"; - reg = <0x11000000 0xcd00>; - interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; - phys = <&hs_phy_1>, <&ss_phy_1>; - phy-names = "usb2-phy", "usb3-phy"; - dr_mode = "host"; - snps,dis_u3_susphy_quirk; - }; - }; - - vsdcc_fixed: vsdcc-regulator { - compatible = "regulator-fixed"; - regulator-name = "SDCC Power"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - }; - - sdcc1bam: dma-controller@12402000 { - compatible = "qcom,bam-v1.3.0"; - reg = <0x12402000 0x8000>; - interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&gcc SDC1_H_CLK>; - clock-names = "bam_clk"; - #dma-cells = <1>; - qcom,ee = <0>; - }; - - sdcc3bam: dma-controller@12182000 { - compatible = "qcom,bam-v1.3.0"; - reg = <0x12182000 0x8000>; - interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&gcc SDC3_H_CLK>; - clock-names = "bam_clk"; - #dma-cells = <1>; - qcom,ee = <0>; - }; - - amba: amba { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <1>; - ranges; - - sdcc1: mmc@12400000 { - status = "disabled"; - compatible = "arm,pl18x", "arm,primecell"; - arm,primecell-periphid = <0x00051180>; - reg = <0x12400000 0x2000>; - interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "cmd_irq"; - clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>; - clock-names = "mclk", "apb_pclk"; - bus-width = <8>; - max-frequency = <96000000>; - non-removable; - cap-sd-highspeed; - cap-mmc-highspeed; - mmc-ddr-1_8v; - vmmc-supply = <&vsdcc_fixed>; - dmas = <&sdcc1bam 2>, <&sdcc1bam 1>; - dma-names = "tx", "rx"; - }; - - sdcc3: mmc@12180000 { - compatible = "arm,pl18x", "arm,primecell"; - arm,primecell-periphid = <0x00051180>; - status = "disabled"; - reg = <0x12180000 0x2000>; - interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "cmd_irq"; - clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>; - clock-names = "mclk", "apb_pclk"; - bus-width = <8>; - cap-sd-highspeed; - cap-mmc-highspeed; - max-frequency = <192000000>; - sd-uhs-sdr104; - sd-uhs-ddr50; - vqmmc-supply = <&vsdcc_fixed>; - dmas = <&sdcc3bam 2>, <&sdcc3bam 1>; - dma-names = "tx", "rx"; - }; - }; - - sfpb_mutex: hwlock@1200600 { - compatible = "qcom,sfpb-mutex"; - reg = <0x01200600 0x100>; - - #hwlock-cells = <1>; - }; }; };Signature · 1 line
2.36.1Signature · 1 line
Ansuel
Bjorn Andersson
AppliedRe: (subset) [PATCH 1/2] ARM: dts: qcom: ipq8064: reorganize node order and sort them
In reply to Christian MarangiQuoted 3 lines · Christian Marangi
Reorganize node order and sort them by address.
Applied, thanks!
[1/2] ARM: dts: qcom: ipq8064: reorganize node order and sort them
commit: ee1e278a84e7578e4aa20820852b7f73b4929c63
[2/2] ARM: dts: qcom: ipq8064: pad addresses to 8 digit
commit: cc02fed341d5f5ea1af531ced213c41a836a3678Best regards,
Signature · 1 line
Bjorn Andersson <[email protected]>