Skip to contentSkip to conversation

"signal is not locked" with HDMI RX driver on RK3588

DISCUSSION Marek Marczykowski-Górecki 3 participants 5 messages Jun 30, 2025 – Jul 2, 2025 Media (V4L/DVB)

lore
Share & tools
lore
#0 lore raw

Hi,

First of all, thanks for all the work regarding upstreaming the driver!

I try to use it on two boards:
- Orange Pi 5B
- Rock 5B+

In both cases, when I use the upstream driver in 6.16-rc, I hit similar issue:
1. v4l2-ctl -d /dev/video2 --set-edid type=hdmi-4k-300mhz - this works
2. EDID is properly presented to the device on the other side of the HDMI cable, I can select to use that "display"
3. But then, the hdmirx complains:

v4l2-ctl -d /dev/video2 --query-dv-timings
VIDIOC_QUERY_DV_TIMINGS: failed: No locks available

And kernel shows:

[ 4033.823023] snps_hdmirx fdee0000.hdmi_receiver: hdmirx_phy_register_write wait cr write done failed
[ 4033.847027] snps_hdmirx fdee0000.hdmi_receiver: hdmirx_phy_register_write wait cr write done failed
[ 4033.870976] snps_hdmirx fdee0000.hdmi_receiver: hdmirx_phy_register_write wait cr write done failed
[ 4033.894998] snps_hdmirx fdee0000.hdmi_receiver: hdmirx_phy_register_write wait cr write done failed
...
[ 4061.975400] fdee0000.hdmi_receiver: hdmirx_query_dv_timings: signal is not locked

In this state actually capturing video stream doesn't work either.

I tried also rockchip-release branch from
https://gitlab.collabora.com/hardware-enablement/rockchip-3588/linux (at 33755850faeb0e53e634390d147cc261a60d2898) with the same result.

If I try the same with the 6.12.13-current-rockchip64 kernel from Armbian, it works fine. I tried to compare the drivers, but there are quite a few differences so it's hard to spot any obvious issue (it could be also an issue somewhere else...).

Any ideas? I can try to add some debugging info or test patches, if you point me what would be helpful.

Signature · 3 lines
Best Regards,
Marek Marczykowski-Górecki
Invisible Things Lab
#1 lore raw
Quoted 32 lines · Marek Marczykowski-Górecki

Hi,

First of all, thanks for all the work regarding upstreaming the driver!

I try to use it on two boards:
- Orange Pi 5B
- Rock 5B+

In both cases, when I use the upstream driver in 6.16-rc, I hit similar issue:
1. v4l2-ctl -d /dev/video2 --set-edid type=hdmi-4k-300mhz - this works
2. EDID is properly presented to the device on the other side of the HDMI cable, I can select to use that "display"
3. But then, the hdmirx complains:

v4l2-ctl -d /dev/video2 --query-dv-timings
VIDIOC_QUERY_DV_TIMINGS: failed: No locks available

And kernel shows:

[ 4033.823023] snps_hdmirx fdee0000.hdmi_receiver: hdmirx_phy_register_write wait cr write done failed
[ 4033.847027] snps_hdmirx fdee0000.hdmi_receiver: hdmirx_phy_register_write wait cr write done failed
[ 4033.870976] snps_hdmirx fdee0000.hdmi_receiver: hdmirx_phy_register_write wait cr write done failed
[ 4033.894998] snps_hdmirx fdee0000.hdmi_receiver: hdmirx_phy_register_write wait cr write done failed
...
[ 4061.975400] fdee0000.hdmi_receiver: hdmirx_query_dv_timings: signal is not locked

In this state actually capturing video stream doesn't work either.

I tried also rockchip-release branch from
https://gitlab.collabora.com/hardware-enablement/rockchip-3588/linux (at 33755850faeb0e53e634390d147cc261a60d2898) with the same result.

Quoted 7 lines

If I try the same with the 6.12.13-current-rockchip64 kernel from Armbian, it works fine. I tried to compare the drivers, but there are quite a few differences so it's hard to spot any obvious issue (it could be also an issue somewhere else...).

Any ideas? I can try to add some debugging info or test patches, if you point me what would be helpful.

If I take u-boot from
https://gitlab.collabora.com/hardware-enablement/rockchip-3588/u-boot/
(rockchip branch at 60501605e3f48b155af83193dfd9ad73362b8e25) and stop loading device-tree from a separate file, I get a different error:

VIDIOC_QUERY_DV_TIMINGS: failed: Numerical result out of range

(and no extra messages from kernel)
My goal is to capture in 4k at 30fps (or even lower), but I get this error also with lower resolutions like 1920x1200@60fps. Unfortunately I don't know which value specifically is out of range...

Signature · 3 lines
Best Regards,
Marek Marczykowski-Górecki
Invisible Things Lab
#2 lore raw

Hi,

Quoted 46 lines · Marek Marczykowski-Górecki
Quoted 32 lines · Marek Marczykowski-Górecki

Hi,

First of all, thanks for all the work regarding upstreaming the driver!

I try to use it on two boards:
- Orange Pi 5B
- Rock 5B+

In both cases, when I use the upstream driver in 6.16-rc, I hit similar issue:
1. v4l2-ctl -d /dev/video2 --set-edid type=hdmi-4k-300mhz - this works
2. EDID is properly presented to the device on the other side of the HDMI cable, I can select to use that "display"
3. But then, the hdmirx complains:

v4l2-ctl -d /dev/video2 --query-dv-timings
VIDIOC_QUERY_DV_TIMINGS: failed: No locks available

And kernel shows:

[ 4033.823023] snps_hdmirx fdee0000.hdmi_receiver: hdmirx_phy_register_write wait cr write done failed
[ 4033.847027] snps_hdmirx fdee0000.hdmi_receiver: hdmirx_phy_register_write wait cr write done failed
[ 4033.870976] snps_hdmirx fdee0000.hdmi_receiver: hdmirx_phy_register_write wait cr write done failed
[ 4033.894998] snps_hdmirx fdee0000.hdmi_receiver: hdmirx_phy_register_write wait cr write done failed
...
[ 4061.975400] fdee0000.hdmi_receiver: hdmirx_query_dv_timings: signal is not locked

In this state actually capturing video stream doesn't work either.

I tried also rockchip-release branch from
https://gitlab.collabora.com/hardware-enablement/rockchip-3588/linux (at 33755850faeb0e53e634390d147cc261a60d2898) with the same result.

Quoted 7 lines

If I try the same with the 6.12.13-current-rockchip64 kernel from Armbian, it works fine. I tried to compare the drivers, but there are quite a few differences so it's hard to spot any obvious issue (it could be also an issue somewhere else...).

Any ideas? I can try to add some debugging info or test patches, if you point me what would be helpful.

If I take u-boot from
https://gitlab.collabora.com/hardware-enablement/rockchip-3588/u-boot/
(rockchip branch at 60501605e3f48b155af83193dfd9ad73362b8e25) and stop loading device-tree from a separate file, I get a different error:

Quoted 6 lines

VIDIOC_QUERY_DV_TIMINGS: failed: Numerical result out of range

(and no extra messages from kernel)
My goal is to capture in 4k at 30fps (or even lower), but I get this error also with lower resolutions like 1920x1200@60fps. Unfortunately I don't know which value specifically is out of range...

You are probably just using the wrong TF-A firmware. Rockchip's binary-only firmware contains a workaround/quirk, which handles the main HDMI-RX interrupt and then provides a virtual one on one of the reserved interrupt lines. The kernel has to use the virtual one, otherwise the driver is not functional.

The upstream (open source) TF-A does not contain this workaround and the kernel must use the original HDMI-RX interrupt line, as the reserved interrupt line is not doing anything at all.

The RK3588 device tree, which is provided as part of the mainline Linux kernel describes the interrupt lines from the hardware and thus needs to be used with the upstream TF-A.

Greetings,

-- Sebastian

#3 lore raw
Quoted 62 lines · Sebastian Reichel

Hi,

Quoted 46 lines · Marek Marczykowski-Górecki
Quoted 32 lines · Marek Marczykowski-Górecki

Hi,

First of all, thanks for all the work regarding upstreaming the driver!

I try to use it on two boards:
- Orange Pi 5B
- Rock 5B+

In both cases, when I use the upstream driver in 6.16-rc, I hit similar issue:
1. v4l2-ctl -d /dev/video2 --set-edid type=hdmi-4k-300mhz - this works
2. EDID is properly presented to the device on the other side of the HDMI cable, I can select to use that "display"
3. But then, the hdmirx complains:

v4l2-ctl -d /dev/video2 --query-dv-timings
VIDIOC_QUERY_DV_TIMINGS: failed: No locks available

And kernel shows:

[ 4033.823023] snps_hdmirx fdee0000.hdmi_receiver: hdmirx_phy_register_write wait cr write done failed
[ 4033.847027] snps_hdmirx fdee0000.hdmi_receiver: hdmirx_phy_register_write wait cr write done failed
[ 4033.870976] snps_hdmirx fdee0000.hdmi_receiver: hdmirx_phy_register_write wait cr write done failed
[ 4033.894998] snps_hdmirx fdee0000.hdmi_receiver: hdmirx_phy_register_write wait cr write done failed
...
[ 4061.975400] fdee0000.hdmi_receiver: hdmirx_query_dv_timings: signal is not locked

In this state actually capturing video stream doesn't work either.

I tried also rockchip-release branch from
https://gitlab.collabora.com/hardware-enablement/rockchip-3588/linux (at 33755850faeb0e53e634390d147cc261a60d2898) with the same result.

Quoted 7 lines

If I try the same with the 6.12.13-current-rockchip64 kernel from Armbian, it works fine. I tried to compare the drivers, but there are quite a few differences so it's hard to spot any obvious issue (it could be also an issue somewhere else...).

Any ideas? I can try to add some debugging info or test patches, if you point me what would be helpful.

If I take u-boot from
https://gitlab.collabora.com/hardware-enablement/rockchip-3588/u-boot/
(rockchip branch at 60501605e3f48b155af83193dfd9ad73362b8e25) and stop loading device-tree from a separate file, I get a different error:

Quoted 6 lines

VIDIOC_QUERY_DV_TIMINGS: failed: Numerical result out of range

(and no extra messages from kernel)
My goal is to capture in 4k at 30fps (or even lower), but I get this error also with lower resolutions like 1920x1200@60fps. Unfortunately I don't know which value specifically is out of range...

You are probably just using the wrong TF-A firmware. Rockchip's binary-only firmware contains a workaround/quirk, which handles the main HDMI-RX interrupt and then provides a virtual one on one of the reserved interrupt lines. The kernel has to use the virtual one, otherwise the driver is not functional.

Quoted 7 lines

The upstream (open source) TF-A does not contain this workaround and the kernel must use the original HDMI-RX interrupt line, as the reserved interrupt line is not doing anything at all.

The RK3588 device tree, which is provided as part of the mainline Linux kernel describes the interrupt lines from the hardware and thus needs to be used with the upstream TF-A.

That was it, thanks! Not it just works!

Is it possible for the driver to detect this situation and either adjust, or at least print some more helpful message? I would have never guessed to look there based on the existing symptoms...

Signature · 3 lines
Best Regards,
Marek Marczykowski-Górecki
Invisible Things Lab
#4 lore raw

...

Quoted 5 lines

That was it, thanks! Not it just works!

Is it possible for the driver to detect this situation and either adjust, or at least print some more helpful message? I would have never guessed to look there based on the existing symptoms...

Hi, glad it works. Potentially should be possible to detect and print a msg. There should've been timeout errors on a driver probe with a wrong FW.

Signature · 2 lines
Best regards,
Dmitry