Skip to contentSkip to conversation

HID: multitouch: fix slab out-of-bounds access in mt_report_fixup()

PATCH RESEND Superseded Qasim Ijaz 3 participants 6 messages Jul 22, 2025 – Jul 23, 2025

Subsystems (2)

v1 of 2 Superseded Latest is v2 →

lore
Share & tools
lore

Qasim Ijaz

author
#0 lore raw

PATCH RESEND 1/1 HID: multitouch: fix slab out-of-bounds access in mt_report_fixup()

A malicious HID device can trigger a slab out-of-bounds during mt_report_fixup() by passing in report descriptor smaller than 607 bytes. mt_report_fixup() attempts to patch byte offset 607 of the descriptor with 0x25 by first checking if byte offset 607 is 0x15 however it lacks bounds checks to verify if the descriptor is big enough before conducting this check. Fix this vulnerability by ensuring the descriptor size is greater than or equal to 608 before accessing it.

Below is the KASAN splat after the out of bounds access happens:

[   13.671954] ==================================================================
[   13.672667] BUG: KASAN: slab-out-of-bounds in mt_report_fixup+0x103/0x110
[   13.673297] Read of size 1 at addr ffff888103df39df by task kworker/0:1/10
[   13.673297] 
[   13.673297] CPU: 0 UID: 0 PID: 10 Comm: kworker/0:1 Not tainted 6.15.0-00005-gec5d573d83f4-dirty #3 
[   13.673297] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.2-debian-1.16.2-1 04/04
[   13.673297] Call Trace:
[   13.673297]  <TASK>
[   13.673297]  dump_stack_lvl+0x5f/0x80
[   13.673297]  print_report+0xd1/0x660
[   13.673297]  kasan_report+0xe5/0x120
[   13.673297]  __asan_report_load1_noabort+0x18/0x20
[   13.673297]  mt_report_fixup+0x103/0x110
[   13.673297]  hid_open_report+0x1ef/0x810
[   13.673297]  mt_probe+0x422/0x960
[   13.673297]  hid_device_probe+0x2e2/0x6f0
[   13.673297]  really_probe+0x1c6/0x6b0
[   13.673297]  __driver_probe_device+0x24f/0x310
[   13.673297]  driver_probe_device+0x4e/0x220
[   13.673297]  __device_attach_driver+0x169/0x320
[   13.673297]  bus_for_each_drv+0x11d/0x1b0
[   13.673297]  __device_attach+0x1b8/0x3e0
[   13.673297]  device_initial_probe+0x12/0x20
[   13.673297]  bus_probe_device+0x13d/0x180
[   13.673297]  device_add+0xe3a/0x1670
[   13.673297]  hid_add_device+0x31d/0xa40

[...]

Fixes c8000deb6836 ("HID: multitouch: Add support for GT7868Q")
---
 drivers/hid/hid-multitouch.c | 25 ++++++++++++++++---------
 1 file changed, 16 insertions(+), 9 deletions(-)
drivers/hid/hid-multitouch.c +16 -9
index 7ac8e16e6158..af4abe3ba410 100644
@@ -1461,18 +1461,25 @@ static const __u8 *mt_report_fixup(struct hid_device *hdev, __u8 *rdesc,
 	if (hdev->vendor == I2C_VENDOR_ID_GOODIX &&
 	    (hdev->product == I2C_DEVICE_ID_GOODIX_01E8 ||
 	     hdev->product == I2C_DEVICE_ID_GOODIX_01E9)) {
-		if (rdesc[607] == 0x15) {
-			rdesc[607] = 0x25;
-			dev_info(
-				&hdev->dev,
-				"GT7868Q report descriptor fixup is applied.\n");
+		if (*size >= 608) {
+			if (rdesc[607] == 0x15) {
+				rdesc[607] = 0x25;
+				dev_info(
+					&hdev->dev,
+					"GT7868Q report descriptor fixup is applied.\n");
+			} else {
+				dev_info(
+					&hdev->dev,
+					"The byte is not expected for fixing the report descriptor. \
+					It's possible that the touchpad firmware is not suitable for applying the fix. \
+					got: %x\n",
+					rdesc[607]);
+			}
 		} else {
 			dev_info(
 				&hdev->dev,
-				"The byte is not expected for fixing the report descriptor. \
-It's possible that the touchpad firmware is not suitable for applying the fix. \
-got: %x\n",
-				rdesc[607]);
+				"GT7868Q fixup: report descriptor only %u bytes, skipping\n",
+				*size);
 		}
 	}
 
Signature · 1 line
2.39.5
Reviewed-by on v1 1/1
#1 lore raw
Quoted 90 lines · Qasim Ijaz

A malicious HID device can trigger a slab out-of-bounds during mt_report_fixup() by passing in report descriptor smaller than 607 bytes. mt_report_fixup() attempts to patch byte offset 607 of the descriptor with 0x25 by first checking if byte offset 607 is 0x15 however it lacks bounds checks to verify if the descriptor is big enough before conducting this check. Fix this vulnerability by ensuring the descriptor size is greater than or equal to 608 before accessing it.

Below is the KASAN splat after the out of bounds access happens:

[   13.671954] ==================================================================
[   13.672667] BUG: KASAN: slab-out-of-bounds in mt_report_fixup+0x103/0x110
[   13.673297] Read of size 1 at addr ffff888103df39df by task kworker/0:1/10
[   13.673297]
[   13.673297] CPU: 0 UID: 0 PID: 10 Comm: kworker/0:1 Not tainted 6.15.0-00005-gec5d573d83f4-dirty #3
[   13.673297] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.2-debian-1.16.2-1 04/04
[   13.673297] Call Trace:
[   13.673297]  <TASK>
[   13.673297]  dump_stack_lvl+0x5f/0x80
[   13.673297]  print_report+0xd1/0x660
[   13.673297]  kasan_report+0xe5/0x120
[   13.673297]  __asan_report_load1_noabort+0x18/0x20
[   13.673297]  mt_report_fixup+0x103/0x110
[   13.673297]  hid_open_report+0x1ef/0x810
[   13.673297]  mt_probe+0x422/0x960
[   13.673297]  hid_device_probe+0x2e2/0x6f0
[   13.673297]  really_probe+0x1c6/0x6b0
[   13.673297]  __driver_probe_device+0x24f/0x310
[   13.673297]  driver_probe_device+0x4e/0x220
[   13.673297]  __device_attach_driver+0x169/0x320
[   13.673297]  bus_for_each_drv+0x11d/0x1b0
[   13.673297]  __device_attach+0x1b8/0x3e0
[   13.673297]  device_initial_probe+0x12/0x20
[   13.673297]  bus_probe_device+0x13d/0x180
[   13.673297]  device_add+0xe3a/0x1670
[   13.673297]  hid_add_device+0x31d/0xa40

[...]

Fixes c8000deb6836 ("HID: multitouch: Add support for GT7868Q")
---
 drivers/hid/hid-multitouch.c | 25 ++++++++++++++++---------
 1 file changed, 16 insertions(+), 9 deletions(-)
drivers/hid/hid-multitouch.c +16 -10
index 7ac8e16e6158..af4abe3ba410 100644
@@ -1461,18 +1461,25 @@ static const __u8 *mt_report_fixup(struct hid_device *hdev, __u8 *rdesc,
        if (hdev->vendor == I2C_VENDOR_ID_GOODIX &&
            (hdev->product == I2C_DEVICE_ID_GOODIX_01E8 ||
             hdev->product == I2C_DEVICE_ID_GOODIX_01E9)) {
-               if (rdesc[607] == 0x15) {
-                       rdesc[607] = 0x25;
-                       dev_info(
-                               &hdev->dev,
-                               "GT7868Q report descriptor fixup is applied.\n");
+               if (*size >= 608) {
+                       if (rdesc[607] == 0x15) {
+                               rdesc[607] = 0x25;
+                               dev_info(
+                                       &hdev->dev,
+                                       "GT7868Q report descriptor fixup is applied.\n");
+                       } else {
+                               dev_info(
+                                       &hdev->dev,
+                                       "The byte is not expected for fixing the report descriptor. \
+                                       It's possible that the touchpad firmware is not suitable for applying the fix. \
+                                       got: %x\n",
+                                       rdesc[607]);
+                       }
                } else {
                        dev_info(
                                &hdev->dev,
-                               "The byte is not expected for fixing the report descriptor. \
-It's possible that the touchpad firmware is not suitable for applying the fix. \
-got: %x\n",
-                               rdesc[607]);
+                               "GT7868Q fixup: report descriptor only %u bytes, skipping\n",
+                               *size);
                }
        }
 
--

2.39.5

#2 lore raw
In reply to Qasim Ijaz
Quoted 62 lines · Qasim Ijaz

A malicious HID device can trigger a slab out-of-bounds during mt_report_fixup() by passing in report descriptor smaller than 607 bytes. mt_report_fixup() attempts to patch byte offset 607 of the descriptor with 0x25 by first checking if byte offset 607 is 0x15 however it lacks bounds checks to verify if the descriptor is big enough before conducting this check. Fix this vulnerability by ensuring the descriptor size is greater than or equal to 608 before accessing it.

Below is the KASAN splat after the out of bounds access happens:

[   13.671954] ==================================================================
[   13.672667] BUG: KASAN: slab-out-of-bounds in mt_report_fixup+0x103/0x110
[   13.673297] Read of size 1 at addr ffff888103df39df by task kworker/0:1/10
[   13.673297]
[   13.673297] CPU: 0 UID: 0 PID: 10 Comm: kworker/0:1 Not tainted 6.15.0-00005-gec5d573d83f4-dirty #3
[   13.673297] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.2-debian-1.16.2-1 04/04
[   13.673297] Call Trace:
[   13.673297]  <TASK>
[   13.673297]  dump_stack_lvl+0x5f/0x80
[   13.673297]  print_report+0xd1/0x660
[   13.673297]  kasan_report+0xe5/0x120
[   13.673297]  __asan_report_load1_noabort+0x18/0x20
[   13.673297]  mt_report_fixup+0x103/0x110
[   13.673297]  hid_open_report+0x1ef/0x810
[   13.673297]  mt_probe+0x422/0x960
[   13.673297]  hid_device_probe+0x2e2/0x6f0
[   13.673297]  really_probe+0x1c6/0x6b0
[   13.673297]  __driver_probe_device+0x24f/0x310
[   13.673297]  driver_probe_device+0x4e/0x220
[   13.673297]  __device_attach_driver+0x169/0x320
[   13.673297]  bus_for_each_drv+0x11d/0x1b0
[   13.673297]  __device_attach+0x1b8/0x3e0
[   13.673297]  device_initial_probe+0x12/0x20
[   13.673297]  bus_probe_device+0x13d/0x180
[   13.673297]  device_add+0xe3a/0x1670
[   13.673297]  hid_add_device+0x31d/0xa40

[...]

Fixes c8000deb6836 ("HID: multitouch: Add support for GT7868Q")
---
  drivers/hid/hid-multitouch.c | 25 ++++++++++++++++---------
  1 file changed, 16 insertions(+), 9 deletions(-)
drivers/hid/hid-multitouch.c +2 -5
index 7ac8e16e6158..af4abe3ba410 100644
@@ -1461,18 +1461,25 @@ static const __u8 *mt_report_fixup(struct hid_device *hdev, __u8 *rdesc,
  	if (hdev->vendor == I2C_VENDOR_ID_GOODIX &&
  	    (hdev->product == I2C_DEVICE_ID_GOODIX_01E8 ||
  	     hdev->product == I2C_DEVICE_ID_GOODIX_01E9)) {
-		if (rdesc[607] == 0x15) {
-			rdesc[607] = 0x25;
-			dev_info(
-				&hdev->dev,
-				"GT7868Q report descriptor fixup is applied.\n");
+		if (*size >= 608) {
+			if (rdesc[607] == 0x15) {

drivers/hid/hid-multitouch.c static const __u8 *mt_report_fixup(struct hid_device *hdev, __u8 *rdesc, · line 1475

Quoted 10 lines
drivers/hid/hid-multitouch.c +10 -0
+				rdesc[607] = 0x25;
+				dev_info(
+					&hdev->dev,
+					"GT7868Q report descriptor fixup is applied.\n");
+			} else {
+				dev_info(
+					&hdev->dev,
+					"The byte is not expected for fixing the report descriptor. \
+					It's possible that the touchpad firmware is not suitable for applying the fix. \
+					got: %x\n",

This is wrong. You have all the spaces/tabs in the string now. Drop all the backslashes, and open and close the string on every line.

drivers/hid/hid-multitouch.c static const __u8 *mt_report_fixup(struct hid_device *hdev, __u8 *rdesc, · line 1477

Quoted 2 lines
drivers/hid/hid-multitouch.c +2 -0
+					rdesc[607]);
+			}

As this is superlong and superindented, perhaps introduce a new function for these devices?

drivers/hid/hid-multitouch.c static const __u8 *mt_report_fixup(struct hid_device *hdev, __u8 *rdesc, · line 1474

Quoted 6 lines
drivers/hid/hid-multitouch.c +0 -3
  		} else {
  			dev_info(
  				&hdev->dev,
-				"The byte is not expected for fixing the report descriptor. \
-It's possible that the touchpad firmware is not suitable for applying the fix. \
-got: %x\n",

This was horrid too, yeah.

drivers/hid/hid-multitouch.c static const __u8 *mt_report_fixup(struct hid_device *hdev, __u8 *rdesc, · line 1481

Quoted 2 lines
drivers/hid/hid-multitouch.c +1 -1
-				rdesc[607]);
+				"GT7868Q fixup: report descriptor only %u bytes, skipping\n",

A predicate missing. Eg. "has only", or "is only".

drivers/hid/hid-multitouch.c static const __u8 *mt_report_fixup(struct hid_device *hdev, __u8 *rdesc, · line 1485

Quoted 4 lines
drivers/hid/hid-multitouch.c +1 -0
+				*size);
  		}
  	}
 

thanks,

Signature · 2 lines
js
suse labs
author
#3 lore raw
Quoted 92 lines · Jiri Slaby
Quoted 62 lines · Qasim Ijaz

A malicious HID device can trigger a slab out-of-bounds during mt_report_fixup() by passing in report descriptor smaller than 607 bytes. mt_report_fixup() attempts to patch byte offset 607 of the descriptor with 0x25 by first checking if byte offset 607 is 0x15 however it lacks bounds checks to verify if the descriptor is big enough before conducting this check. Fix this vulnerability by ensuring the descriptor size is greater than or equal to 608 before accessing it.

Below is the KASAN splat after the out of bounds access happens:

[   13.671954] ==================================================================
[   13.672667] BUG: KASAN: slab-out-of-bounds in mt_report_fixup+0x103/0x110
[   13.673297] Read of size 1 at addr ffff888103df39df by task kworker/0:1/10
[   13.673297]
[   13.673297] CPU: 0 UID: 0 PID: 10 Comm: kworker/0:1 Not tainted 6.15.0-00005-gec5d573d83f4-dirty #3
[   13.673297] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.2-debian-1.16.2-1 04/04
[   13.673297] Call Trace:
[   13.673297]  <TASK>
[   13.673297]  dump_stack_lvl+0x5f/0x80
[   13.673297]  print_report+0xd1/0x660
[   13.673297]  kasan_report+0xe5/0x120
[   13.673297]  __asan_report_load1_noabort+0x18/0x20
[   13.673297]  mt_report_fixup+0x103/0x110
[   13.673297]  hid_open_report+0x1ef/0x810
[   13.673297]  mt_probe+0x422/0x960
[   13.673297]  hid_device_probe+0x2e2/0x6f0
[   13.673297]  really_probe+0x1c6/0x6b0
[   13.673297]  __driver_probe_device+0x24f/0x310
[   13.673297]  driver_probe_device+0x4e/0x220
[   13.673297]  __device_attach_driver+0x169/0x320
[   13.673297]  bus_for_each_drv+0x11d/0x1b0
[   13.673297]  __device_attach+0x1b8/0x3e0
[   13.673297]  device_initial_probe+0x12/0x20
[   13.673297]  bus_probe_device+0x13d/0x180
[   13.673297]  device_add+0xe3a/0x1670
[   13.673297]  hid_add_device+0x31d/0xa40

[...]

Fixes c8000deb6836 ("HID: multitouch: Add support for GT7868Q")
---
  drivers/hid/hid-multitouch.c | 25 ++++++++++++++++---------
  1 file changed, 16 insertions(+), 9 deletions(-)
drivers/hid/hid-multitouch.c +2 -5
index 7ac8e16e6158..af4abe3ba410 100644
@@ -1461,18 +1461,25 @@ static const __u8 *mt_report_fixup(struct hid_device *hdev, __u8 *rdesc,
  	if (hdev->vendor == I2C_VENDOR_ID_GOODIX &&
  	    (hdev->product == I2C_DEVICE_ID_GOODIX_01E8 ||
  	     hdev->product == I2C_DEVICE_ID_GOODIX_01E9)) {
-		if (rdesc[607] == 0x15) {
-			rdesc[607] = 0x25;
-			dev_info(
-				&hdev->dev,
-				"GT7868Q report descriptor fixup is applied.\n");
+		if (*size >= 608) {
+			if (rdesc[607] == 0x15) {

drivers/hid/hid-multitouch.c static const __u8 *mt_report_fixup(struct hid_device *hdev, __u8 *rdesc, · line 1475

Quoted 10 lines
drivers/hid/hid-multitouch.c +10 -0
+				rdesc[607] = 0x25;
+				dev_info(
+					&hdev->dev,
+					"GT7868Q report descriptor fixup is applied.\n");
+			} else {
+				dev_info(
+					&hdev->dev,
+					"The byte is not expected for fixing the report descriptor. \
+					It's possible that the touchpad firmware is not suitable for applying the fix. \
+					got: %x\n",

This is wrong. You have all the spaces/tabs in the string now. Drop all the backslashes, and open and close the string on every line.

drivers/hid/hid-multitouch.c static const __u8 *mt_report_fixup(struct hid_device *hdev, __u8 *rdesc, · line 1477

Quoted 2 lines
drivers/hid/hid-multitouch.c +2 -0
+					rdesc[607]);
+			}

As this is superlong and superindented, perhaps introduce a new function for these devices?

drivers/hid/hid-multitouch.c static const __u8 *mt_report_fixup(struct hid_device *hdev, __u8 *rdesc, · line 1474

Quoted 6 lines
drivers/hid/hid-multitouch.c +0 -3
  		} else {
  			dev_info(
  				&hdev->dev,
-				"The byte is not expected for fixing the report descriptor. \
-It's possible that the touchpad firmware is not suitable for applying the fix. \
-got: %x\n",

This was horrid too, yeah.

Quoted 5 lines

drivers/hid/hid-multitouch.c static const __u8 *mt_report_fixup(struct hid_device *hdev, __u8 *rdesc, · line 1481

Quoted 2 lines
drivers/hid/hid-multitouch.c +1 -1
-				rdesc[607]);
+				"GT7868Q fixup: report descriptor only %u bytes, skipping\n",

A predicate missing. Eg. "has only", or "is only".

Thanks for the feedback Jiri, I took the advice on board, is something like this better?

static const __u8 *mt_report_fixup(struct hid_device *hdev, __u8 *rdesc,
unsigned int *size)

 {
          if (hdev->vendor == I2C_VENDOR_ID_GOODIX &&
              (hdev->product == I2C_DEVICE_ID_GOODIX_01E8 ||
               hdev->product == I2C_DEVICE_ID_GOODIX_01E9)) {
		 if (*size < 608) {
			 dev_info(
				 &hdev->dev,
				 "GT7868Q fixup: report descriptor is only %u bytes, skipping\n",
				 *size);
                          return rdesc;
                  }
 
		 if (rdesc[607] == 0x15) {
			 rdesc[607] = 0x25;
			 dev_info(
				 &hdev->dev,
				 "GT7868Q fixup: report descriptor fixup is applied.\n");
		 } else {
			 dev_info(&hdev->dev,
				 "GT7868Q fixup: offset 607 is %x (expected 0x15), "
				 "descriptor may be malformed, skipping\n",
				 rdesc[607]);
		 }
	  }

return rdesc;
}

the key changes I made are:

- Move size check to the top, this way the indentation level is decent
- get rid of message backslashes
- shorten the fixup failure message when rdesc[607] is not 0x15 and make it a bit clearer since this message was the longest - just a minor cleanup
- added "is only %u bytes" as you suggested

if this is all good I can send v2.

Thanks
qasim

Quoted 9 lines

drivers/hid/hid-multitouch.c static const __u8 *mt_report_fixup(struct hid_device *hdev, __u8 *rdesc, · line 1484

Quoted 3 lines
drivers/hid/hid-multitouch.c +1 -0
+				*size);
  		}
  	}

thanks,

Signature · 2 lines
js
suse labs
#4 lore raw
Quoted 93 lines · Qasim Ijaz
Quoted 92 lines · Jiri Slaby
Quoted 62 lines · Qasim Ijaz

A malicious HID device can trigger a slab out-of-bounds during mt_report_fixup() by passing in report descriptor smaller than 607 bytes. mt_report_fixup() attempts to patch byte offset 607 of the descriptor with 0x25 by first checking if byte offset 607 is 0x15 however it lacks bounds checks to verify if the descriptor is big enough before conducting this check. Fix this vulnerability by ensuring the descriptor size is greater than or equal to 608 before accessing it.

Below is the KASAN splat after the out of bounds access happens:

[   13.671954] ==================================================================
[   13.672667] BUG: KASAN: slab-out-of-bounds in mt_report_fixup+0x103/0x110
[   13.673297] Read of size 1 at addr ffff888103df39df by task kworker/0:1/10
[   13.673297]
[   13.673297] CPU: 0 UID: 0 PID: 10 Comm: kworker/0:1 Not tainted 6.15.0-00005-gec5d573d83f4-dirty #3
[   13.673297] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.2-debian-1.16.2-1 04/04
[   13.673297] Call Trace:
[   13.673297]  <TASK>
[   13.673297]  dump_stack_lvl+0x5f/0x80
[   13.673297]  print_report+0xd1/0x660
[   13.673297]  kasan_report+0xe5/0x120
[   13.673297]  __asan_report_load1_noabort+0x18/0x20
[   13.673297]  mt_report_fixup+0x103/0x110
[   13.673297]  hid_open_report+0x1ef/0x810
[   13.673297]  mt_probe+0x422/0x960
[   13.673297]  hid_device_probe+0x2e2/0x6f0
[   13.673297]  really_probe+0x1c6/0x6b0
[   13.673297]  __driver_probe_device+0x24f/0x310
[   13.673297]  driver_probe_device+0x4e/0x220
[   13.673297]  __device_attach_driver+0x169/0x320
[   13.673297]  bus_for_each_drv+0x11d/0x1b0
[   13.673297]  __device_attach+0x1b8/0x3e0
[   13.673297]  device_initial_probe+0x12/0x20
[   13.673297]  bus_probe_device+0x13d/0x180
[   13.673297]  device_add+0xe3a/0x1670
[   13.673297]  hid_add_device+0x31d/0xa40

[...]

Fixes c8000deb6836 ("HID: multitouch: Add support for GT7868Q")
---
   drivers/hid/hid-multitouch.c | 25 ++++++++++++++++---------
   1 file changed, 16 insertions(+), 9 deletions(-)
drivers/hid/hid-multitouch.c +2 -5
index 7ac8e16e6158..af4abe3ba410 100644
@@ -1461,18 +1461,25 @@ static const __u8 *mt_report_fixup(struct hid_device *hdev, __u8 *rdesc,
   	if (hdev->vendor == I2C_VENDOR_ID_GOODIX &&
   	    (hdev->product == I2C_DEVICE_ID_GOODIX_01E8 ||
   	     hdev->product == I2C_DEVICE_ID_GOODIX_01E9)) {
-		if (rdesc[607] == 0x15) {
-			rdesc[607] = 0x25;
-			dev_info(
-				&hdev->dev,
-				"GT7868Q report descriptor fixup is applied.\n");
+		if (*size >= 608) {
+			if (rdesc[607] == 0x15) {

drivers/hid/hid-multitouch.c static const __u8 *mt_report_fixup(struct hid_device *hdev, __u8 *rdesc, · line 1475

Quoted 10 lines
drivers/hid/hid-multitouch.c +10 -0
+				rdesc[607] = 0x25;
+				dev_info(
+					&hdev->dev,
+					"GT7868Q report descriptor fixup is applied.\n");
+			} else {
+				dev_info(
+					&hdev->dev,
+					"The byte is not expected for fixing the report descriptor. \
+					It's possible that the touchpad firmware is not suitable for applying the fix. \
+					got: %x\n",

This is wrong. You have all the spaces/tabs in the string now. Drop all the backslashes, and open and close the string on every line.

drivers/hid/hid-multitouch.c static const __u8 *mt_report_fixup(struct hid_device *hdev, __u8 *rdesc, · line 1477

Quoted 2 lines
drivers/hid/hid-multitouch.c +2 -0
+					rdesc[607]);
+			}

As this is superlong and superindented, perhaps introduce a new function for these devices?

drivers/hid/hid-multitouch.c static const __u8 *mt_report_fixup(struct hid_device *hdev, __u8 *rdesc, · line 1474

Quoted 6 lines
drivers/hid/hid-multitouch.c +0 -3
   		} else {
   			dev_info(
   				&hdev->dev,
-				"The byte is not expected for fixing the report descriptor. \
-It's possible that the touchpad firmware is not suitable for applying the fix. \
-got: %x\n",

This was horrid too, yeah.

Quoted 8 lines
Quoted 5 lines

drivers/hid/hid-multitouch.c static const __u8 *mt_report_fixup(struct hid_device *hdev, __u8 *rdesc, · line 1481

Quoted 2 lines
drivers/hid/hid-multitouch.c +1 -1
-				rdesc[607]);
+				"GT7868Q fixup: report descriptor only %u bytes, skipping\n",

A predicate missing. Eg. "has only", or "is only".

Thanks for the feedback Jiri, I took the advice on board, is something like this better?

Definitely.

Quoted 32 lines

static const __u8 *mt_report_fixup(struct hid_device *hdev, __u8 *rdesc,
unsigned int *size)

  {
           if (hdev->vendor == I2C_VENDOR_ID_GOODIX &&
               (hdev->product == I2C_DEVICE_ID_GOODIX_01E8 ||
                hdev->product == I2C_DEVICE_ID_GOODIX_01E9)) {
		 if (*size < 608) {
			 dev_info(
				 &hdev->dev,
				 "GT7868Q fixup: report descriptor is only %u bytes, skipping\n",
				 *size);
                           return rdesc;
                   }
  
		 if (rdesc[607] == 0x15) {
			 rdesc[607] = 0x25;
			 dev_info(
				 &hdev->dev,
				 "GT7868Q fixup: report descriptor fixup is applied.\n");
		 } else {
			 dev_info(&hdev->dev,
				 "GT7868Q fixup: offset 607 is %x (expected 0x15), "
				 "descriptor may be malformed, skipping\n",
				 rdesc[607]);
		 }
	  }
  	  return rdesc;
  }

the key changes I made are:

Quoted 8 lines

- Move size check to the top, this way the indentation level is decent
- get rid of message backslashes
- shorten the fixup failure message when rdesc[607] is not 0x15 and make it a bit clearer since this message was the longest - just a minor cleanup
- added "is only %u bytes" as you suggested

if this is all good I can send v2.

I would invert the conditions. So the code would look like:

static bool goodix_needs_fixup(hdev)
{
if (hdev->vendor != I2C_VENDOR_ID_GOODIX)

    return false;

return hdev->product == I2C_DEVICE_ID_GOODIX_01E8 ||

                 hdev->product == I2C_DEVICE_ID_GOODIX_01E9;
}

static const __u8 *mt_report_fixup(struct hid_device *hdev, __u8 *rdesc,
unsigned int *size)
{
if (!goodix_needs_fixup(hdev))

    return rdesc;

if (*size < 608) {
dev_info(&hdev->dev,
"GT7868Q fixup: report descriptor is only %u bytes,
skipping\n",

 	     *size);
    return rdesc;

}

  if (rdesc[607] != 0x15) {
    dev_info(&hdev->dev,
 	 "GT7868Q fixup: offset 607 is %x (expected 0x15), descriptor may be 
malformed, skipping\n",
         rdesc[607]);
    return rdesc;

}

rdesc[607] = 0x25;
dev_info(&hdev->dev,
"GT7868Q fixup: report descriptor fixup is applied.\n");

return rdesc;
}

thanks,

Signature · 2 lines
js
suse labs
author
#5 lore raw
Quoted 175 lines · Jiri Slaby
Quoted 93 lines · Qasim Ijaz
Quoted 92 lines · Jiri Slaby
Quoted 62 lines · Qasim Ijaz

A malicious HID device can trigger a slab out-of-bounds during mt_report_fixup() by passing in report descriptor smaller than 607 bytes. mt_report_fixup() attempts to patch byte offset 607 of the descriptor with 0x25 by first checking if byte offset 607 is 0x15 however it lacks bounds checks to verify if the descriptor is big enough before conducting this check. Fix this vulnerability by ensuring the descriptor size is greater than or equal to 608 before accessing it.

Below is the KASAN splat after the out of bounds access happens:

[   13.671954] ==================================================================
[   13.672667] BUG: KASAN: slab-out-of-bounds in mt_report_fixup+0x103/0x110
[   13.673297] Read of size 1 at addr ffff888103df39df by task kworker/0:1/10
[   13.673297]
[   13.673297] CPU: 0 UID: 0 PID: 10 Comm: kworker/0:1 Not tainted 6.15.0-00005-gec5d573d83f4-dirty #3
[   13.673297] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.2-debian-1.16.2-1 04/04
[   13.673297] Call Trace:
[   13.673297]  <TASK>
[   13.673297]  dump_stack_lvl+0x5f/0x80
[   13.673297]  print_report+0xd1/0x660
[   13.673297]  kasan_report+0xe5/0x120
[   13.673297]  __asan_report_load1_noabort+0x18/0x20
[   13.673297]  mt_report_fixup+0x103/0x110
[   13.673297]  hid_open_report+0x1ef/0x810
[   13.673297]  mt_probe+0x422/0x960
[   13.673297]  hid_device_probe+0x2e2/0x6f0
[   13.673297]  really_probe+0x1c6/0x6b0
[   13.673297]  __driver_probe_device+0x24f/0x310
[   13.673297]  driver_probe_device+0x4e/0x220
[   13.673297]  __device_attach_driver+0x169/0x320
[   13.673297]  bus_for_each_drv+0x11d/0x1b0
[   13.673297]  __device_attach+0x1b8/0x3e0
[   13.673297]  device_initial_probe+0x12/0x20
[   13.673297]  bus_probe_device+0x13d/0x180
[   13.673297]  device_add+0xe3a/0x1670
[   13.673297]  hid_add_device+0x31d/0xa40

[...]

Fixes c8000deb6836 ("HID: multitouch: Add support for GT7868Q")
---
   drivers/hid/hid-multitouch.c | 25 ++++++++++++++++---------
   1 file changed, 16 insertions(+), 9 deletions(-)
drivers/hid/hid-multitouch.c +2 -5
index 7ac8e16e6158..af4abe3ba410 100644
@@ -1461,18 +1461,25 @@ static const __u8 *mt_report_fixup(struct hid_device *hdev, __u8 *rdesc,
   	if (hdev->vendor == I2C_VENDOR_ID_GOODIX &&
   	    (hdev->product == I2C_DEVICE_ID_GOODIX_01E8 ||
   	     hdev->product == I2C_DEVICE_ID_GOODIX_01E9)) {
-		if (rdesc[607] == 0x15) {
-			rdesc[607] = 0x25;
-			dev_info(
-				&hdev->dev,
-				"GT7868Q report descriptor fixup is applied.\n");
+		if (*size >= 608) {
+			if (rdesc[607] == 0x15) {

drivers/hid/hid-multitouch.c static const __u8 *mt_report_fixup(struct hid_device *hdev, __u8 *rdesc, · line 1475

Quoted 10 lines
drivers/hid/hid-multitouch.c +10 -0
+				rdesc[607] = 0x25;
+				dev_info(
+					&hdev->dev,
+					"GT7868Q report descriptor fixup is applied.\n");
+			} else {
+				dev_info(
+					&hdev->dev,
+					"The byte is not expected for fixing the report descriptor. \
+					It's possible that the touchpad firmware is not suitable for applying the fix. \
+					got: %x\n",

This is wrong. You have all the spaces/tabs in the string now. Drop all the backslashes, and open and close the string on every line.

drivers/hid/hid-multitouch.c static const __u8 *mt_report_fixup(struct hid_device *hdev, __u8 *rdesc, · line 1477

Quoted 2 lines
drivers/hid/hid-multitouch.c +2 -0
+					rdesc[607]);
+			}

As this is superlong and superindented, perhaps introduce a new function for these devices?

drivers/hid/hid-multitouch.c static const __u8 *mt_report_fixup(struct hid_device *hdev, __u8 *rdesc, · line 1474

Quoted 6 lines
drivers/hid/hid-multitouch.c +0 -3
   		} else {
   			dev_info(
   				&hdev->dev,
-				"The byte is not expected for fixing the report descriptor. \
-It's possible that the touchpad firmware is not suitable for applying the fix. \
-got: %x\n",

This was horrid too, yeah.

Quoted 8 lines
Quoted 5 lines

drivers/hid/hid-multitouch.c static const __u8 *mt_report_fixup(struct hid_device *hdev, __u8 *rdesc, · line 1481

Quoted 2 lines
drivers/hid/hid-multitouch.c +1 -1
-				rdesc[607]);
+				"GT7868Q fixup: report descriptor only %u bytes, skipping\n",

A predicate missing. Eg. "has only", or "is only".

Thanks for the feedback Jiri, I took the advice on board, is something like this better?

Definitely.

Quoted 30 lines

static const __u8 *mt_report_fixup(struct hid_device *hdev, __u8 *rdesc,
unsigned int *size)

  {
           if (hdev->vendor == I2C_VENDOR_ID_GOODIX &&
               (hdev->product == I2C_DEVICE_ID_GOODIX_01E8 ||
                hdev->product == I2C_DEVICE_ID_GOODIX_01E9)) {
		 if (*size < 608) {
			 dev_info(
				 &hdev->dev,
				 "GT7868Q fixup: report descriptor is only %u bytes, skipping\n",
				 *size);
                           return rdesc;
                   }
		 if (rdesc[607] == 0x15) {
			 rdesc[607] = 0x25;
			 dev_info(
				 &hdev->dev,
				 "GT7868Q fixup: report descriptor fixup is applied.\n");
		 } else {
			 dev_info(&hdev->dev,
				 "GT7868Q fixup: offset 607 is %x (expected 0x15), "
				 "descriptor may be malformed, skipping\n",
				 rdesc[607]);
		 }
	  }

return rdesc;
}

the key changes I made are:

Quoted 8 lines

- Move size check to the top, this way the indentation level is decent
- get rid of message backslashes
- shorten the fixup failure message when rdesc[607] is not 0x15 and make it a bit clearer since this message was the longest - just a minor cleanup
- added "is only %u bytes" as you suggested

if this is all good I can send v2.

I would invert the conditions. So the code would look like:

static bool goodix_needs_fixup(hdev)
{
if (hdev->vendor != I2C_VENDOR_ID_GOODIX)

    return false;

return hdev->product == I2C_DEVICE_ID_GOODIX_01E8 ||

                 hdev->product == I2C_DEVICE_ID_GOODIX_01E9;
}

static const __u8 *mt_report_fixup(struct hid_device *hdev, __u8 *rdesc,
unsigned int *size)
{
if (!goodix_needs_fixup(hdev))

    return rdesc;

if (*size < 608) {
dev_info(&hdev->dev,
"GT7868Q fixup: report descriptor is only %u bytes,
skipping\n",

(quoted diff) +0 -0
 	     *size);
    return rdesc;
  }
 
  if (rdesc[607] != 0x15) {
    dev_info(&hdev->dev,
 	 "GT7868Q fixup: offset 607 is %x (expected 0x15), descriptor may be

malformed, skipping\n",

         rdesc[607]);
    return rdesc;
Quoted 8 lines

}

rdesc[607] = 0x25;
dev_info(&hdev->dev,
"GT7868Q fixup: report descriptor fixup is applied.\n");

return rdesc;
}

Thanks Jiri, this looks good. I think Ill split this into 2 patches one for fixing the OOB with a size check and the second for a general function cleanup. Hope that sounds good.

Thanks
qasim

Quoted 5 lines

thanks,

Signature · 2 lines
js
suse labs