Skip to contentSkip to conversation

net: stmmac: lpc18xx and sti: convert to set_phy_intf_sel()

PATCH Applied Russell King (Oracle) 3 participants 11 messages Nov 6, 2025 – Nov 8, 2025

Subsystems (5)
Networking Network drivers Arm STM32 stmmac Ethernet driver +1 more subsystems
lore
Share & tools
lore

Russell King (Oracle)

author
#0 lore raw

cover net: stmmac: lpc18xx and sti: convert to set_phy_intf_sel()

This series converts lpc18xx and sti to use the new .set_phy_intf_sel() method.

 .../net/ethernet/stmicro/stmmac/dwmac-lpc18xx.c    | 42 ++++++++++--------
 drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c    | 50 ++++++++--------------
 2 files changed, 42 insertions(+), 50 deletions(-)
Signature · 2 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 80Mbps down 10Mbps up. Decent connectivity at last!
#1 lore raw

PATCH 1/9 net: stmmac: lpc18xx: convert to PHY_INTF_SEL_x

Use the common dwmac definitions for the PHY interface selection field.

Signed-off-by Russell King (Oracle) <[email protected]>
---
 drivers/net/ethernet/stmicro/stmmac/dwmac-lpc18xx.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-lpc18xx.c +2 -2
index 6fffc9dfbae5..66c309a7afb3 100644
@@ -22,8 +22,8 @@
 /* Register defines for CREG syscon */
 #define LPC18XX_CREG_CREG6			0x12c
 # define LPC18XX_CREG_CREG6_ETHMODE_MASK	0x7
-# define LPC18XX_CREG_CREG6_ETHMODE_MII		0x0
-# define LPC18XX_CREG_CREG6_ETHMODE_RMII	0x4
+# define LPC18XX_CREG_CREG6_ETHMODE_MII		PHY_INTF_SEL_GMII_MII
+# define LPC18XX_CREG_CREG6_ETHMODE_RMII	PHY_INTF_SEL_RMII
 
 static int lpc18xx_dwmac_probe(struct platform_device *pdev)
 {
Signature · 1 line
2.47.3
#2 lore raw

PATCH 2/9 net: stmmac: lpc18xx: use PHY_INTF_SEL_x directly

In reply to Russell King (Oracle)

Use the PHY_INTF_SEL_x values directly rather than the driver private LPC18XX_CREG_CREG6_ETHMODE_x definitions, and convert LPC18XX_CREG_CREG6_ETHMODE_MASK to use GENMASK().

Signed-off-by Russell King (Oracle) <[email protected]>
---
 drivers/net/ethernet/stmicro/stmmac/dwmac-lpc18xx.c | 8 +++-----
 1 file changed, 3 insertions(+), 5 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-lpc18xx.c +3 -5
index 66c309a7afb3..895d16dc0a4b 100644
@@ -21,9 +21,7 @@
 
 /* Register defines for CREG syscon */
 #define LPC18XX_CREG_CREG6			0x12c
-# define LPC18XX_CREG_CREG6_ETHMODE_MASK	0x7
-# define LPC18XX_CREG_CREG6_ETHMODE_MII		PHY_INTF_SEL_GMII_MII
-# define LPC18XX_CREG_CREG6_ETHMODE_RMII	PHY_INTF_SEL_RMII
+# define LPC18XX_CREG_CREG6_ETHMODE_MASK	GENMASK(2, 0)
 
 static int lpc18xx_dwmac_probe(struct platform_device *pdev)
 {

@@ -50,9 +48,9 @@ static int lpc18xx_dwmac_probe(struct platform_device *pdev)
 	}
 
 	if (plat_dat->phy_interface == PHY_INTERFACE_MODE_MII) {
-		ethmode = LPC18XX_CREG_CREG6_ETHMODE_MII;
+		ethmode = PHY_INTF_SEL_GMII_MII;
 	} else if (plat_dat->phy_interface == PHY_INTERFACE_MODE_RMII) {
-		ethmode = LPC18XX_CREG_CREG6_ETHMODE_RMII;
+		ethmode = PHY_INTF_SEL_RMII;
 	} else {
 		dev_err(&pdev->dev, "Only MII and RMII mode supported\n");
 		return -EINVAL;
Signature · 1 line
2.47.3
#3 lore raw

PATCH 3/9 net: stmmac: lpc18xx: use stmmac_get_phy_intf_sel()

In reply to Russell King (Oracle)

Use stmmac_get_phy_intf_sel() to decode the PHY interface mode to the phy_intf_sel value, and use the result to program the ethernet mode.

Signed-off-by Russell King (Oracle) <[email protected]>
---
 drivers/net/ethernet/stmicro/stmmac/dwmac-lpc18xx.c | 9 ++++-----
 1 file changed, 4 insertions(+), 5 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-lpc18xx.c +4 -5
index 895d16dc0a4b..0f6be2a17e65 100644
@@ -47,15 +47,14 @@ static int lpc18xx_dwmac_probe(struct platform_device *pdev)
 		return PTR_ERR(reg);
 	}
 
-	if (plat_dat->phy_interface == PHY_INTERFACE_MODE_MII) {
-		ethmode = PHY_INTF_SEL_GMII_MII;
-	} else if (plat_dat->phy_interface == PHY_INTERFACE_MODE_RMII) {
-		ethmode = PHY_INTF_SEL_RMII;
-	} else {
+	if (plat_dat->phy_interface != PHY_INTERFACE_MODE_MII &&
+	    plat_dat->phy_interface != PHY_INTERFACE_MODE_RMII) {
 		dev_err(&pdev->dev, "Only MII and RMII mode supported\n");
 		return -EINVAL;
 	}
 
+	ethmode = stmmac_get_phy_intf_sel(plat_dat->phy_interface);
+
 	regmap_update_bits(reg, LPC18XX_CREG_CREG6,
 			   LPC18XX_CREG_CREG6_ETHMODE_MASK, ethmode);
Signature · 1 line
2.47.3
#4 lore raw

PATCH 4/9 net: stmmac: lpc18xx: validate phy_intf_sel

In reply to Russell King (Oracle)

Validate the phy_intf_sel value rather than the PHY interface mode. This will allow us to transition to the ->set_phy_intf_sel() method. Note that this will allow GMII as well as MII as the phy_intf_sel value is the same for both.

Signed-off-by Russell King (Oracle) <[email protected]>
---
 drivers/net/ethernet/stmicro/stmmac/dwmac-lpc18xx.c | 7 +++----
 1 file changed, 3 insertions(+), 4 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-lpc18xx.c +3 -4
index 0f6be2a17e65..ec60968113b8 100644
@@ -47,14 +47,13 @@ static int lpc18xx_dwmac_probe(struct platform_device *pdev)
 		return PTR_ERR(reg);
 	}
 
-	if (plat_dat->phy_interface != PHY_INTERFACE_MODE_MII &&
-	    plat_dat->phy_interface != PHY_INTERFACE_MODE_RMII) {
+	ethmode = stmmac_get_phy_intf_sel(plat_dat->phy_interface);
+	if (ethmode != PHY_INTF_SEL_GMII_MII &&
+	    ethmode != PHY_INTF_SEL_RMII) {
 		dev_err(&pdev->dev, "Only MII and RMII mode supported\n");
 		return -EINVAL;
 	}
 
-	ethmode = stmmac_get_phy_intf_sel(plat_dat->phy_interface);
-
 	regmap_update_bits(reg, LPC18XX_CREG_CREG6,
 			   LPC18XX_CREG_CREG6_ETHMODE_MASK, ethmode);
Signature · 1 line
2.47.3
#5 lore raw

PATCH 5/9 net: stmmac: lpc18xx: use ->set_phy_intf_sel()

In reply to Russell King (Oracle)

Move the configuration of the dwmac PHY interface selection to the new ->set_phy_intf_sel() method.

Signed-off-by Russell King (Oracle) <[email protected]>
---
 .../ethernet/stmicro/stmmac/dwmac-lpc18xx.c   | 36 +++++++++++--------
 1 file changed, 22 insertions(+), 14 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-lpc18xx.c +22 -14
index ec60968113b8..c68d7de1f8ac 100644
@@ -23,12 +23,27 @@
 #define LPC18XX_CREG_CREG6			0x12c
 # define LPC18XX_CREG_CREG6_ETHMODE_MASK	GENMASK(2, 0)
 
+static int lpc18xx_set_phy_intf_sel(void *bsp_priv, u8 phy_intf_sel)
+{
+	struct regmap *reg = bsp_priv;
+
+	if (phy_intf_sel != PHY_INTF_SEL_GMII_MII &&
+	    phy_intf_sel != PHY_INTF_SEL_RMII)
+		return -EINVAL;
+
+	regmap_update_bits(reg, LPC18XX_CREG_CREG6,
+			   LPC18XX_CREG_CREG6_ETHMODE_MASK,
+			   FIELD_PREP(LPC18XX_CREG_CREG6_ETHMODE_MASK,
+				      phy_intf_sel));
+
+	return 0;
+}
+
 static int lpc18xx_dwmac_probe(struct platform_device *pdev)
 {
 	struct plat_stmmacenet_data *plat_dat;
 	struct stmmac_resources stmmac_res;
-	struct regmap *reg;
-	u8 ethmode;
+	struct regmap *regmap;
 	int ret;
 
 	ret = stmmac_get_platform_resources(pdev, &stmmac_res);

@@ -41,21 +56,14 @@ static int lpc18xx_dwmac_probe(struct platform_device *pdev)
 
 	plat_dat->core_type = DWMAC_CORE_GMAC;
 
-	reg = syscon_regmap_lookup_by_compatible("nxp,lpc1850-creg");
-	if (IS_ERR(reg)) {
+	regmap = syscon_regmap_lookup_by_compatible("nxp,lpc1850-creg");
+	if (IS_ERR(regmap)) {
 		dev_err(&pdev->dev, "syscon lookup failed\n");
-		return PTR_ERR(reg);
-	}
-
-	ethmode = stmmac_get_phy_intf_sel(plat_dat->phy_interface);
-	if (ethmode != PHY_INTF_SEL_GMII_MII &&
-	    ethmode != PHY_INTF_SEL_RMII) {
-		dev_err(&pdev->dev, "Only MII and RMII mode supported\n");
-		return -EINVAL;
+		return PTR_ERR(regmap);
 	}
 
-	regmap_update_bits(reg, LPC18XX_CREG_CREG6,
-			   LPC18XX_CREG_CREG6_ETHMODE_MASK, ethmode);
+	plat_dat->bsp_priv = regmap;
+	plat_dat->set_phy_intf_sel = lpc18xx_set_phy_intf_sel;
 
 	return stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res);
 }
Signature · 1 line
2.47.3
#6 lore raw

PATCH 6/9 net: stmmac: sti: use PHY_INTF_SEL_x to select PHY interface

In reply to Russell King (Oracle)

Use the common dwmac definitions for the PHY interface selection field, adding MII_PHY_SEL_VAL() temporarily to avoid line wrapping.

Signed-off-by Russell King (Oracle) <[email protected]>
---
 drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c | 12 +++++++-----
 1 file changed, 7 insertions(+), 5 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c +7 -5
index 53d5ce1f6dc6..1e8769a81d77 100644
@@ -77,13 +77,15 @@
  *	001-RGMII
  *	010-SGMII
  *	100-RMII
+ * These are the DW MAC phy_intf_sel values
  */
 #define MII_PHY_SEL_MASK	GENMASK(4, 2)
-#define ETH_PHY_SEL_RMII	BIT(4)
-#define ETH_PHY_SEL_SGMII	BIT(3)
-#define ETH_PHY_SEL_RGMII	BIT(2)
-#define ETH_PHY_SEL_GMII	0x0
-#define ETH_PHY_SEL_MII		0x0
+#define MII_PHY_SEL_VAL(val)	FIELD_PREP_CONST(MII_PHY_SEL_MASK, val)
+#define ETH_PHY_SEL_RMII	MII_PHY_SEL_VAL(PHY_INTF_SEL_RMII)
+#define ETH_PHY_SEL_SGMII	MII_PHY_SEL_VAL(PHY_INTF_SEL_SGMII)
+#define ETH_PHY_SEL_RGMII	MII_PHY_SEL_VAL(PHY_INTF_SEL_RGMII)
+#define ETH_PHY_SEL_GMII	MII_PHY_SEL_VAL(PHY_INTF_SEL_GMII_MII)
+#define ETH_PHY_SEL_MII		MII_PHY_SEL_VAL(PHY_INTF_SEL_GMII_MII)
 
 struct sti_dwmac {
 	phy_interface_t interface;	/* MII interface */
Signature · 1 line
2.47.3
#7 lore raw

PATCH 7/9 net: stmmac: sti: use PHY_INTF_SEL_x directly

In reply to Russell King (Oracle)

Use the PHY_INTF_SEL_x values directly rather than the driver private ETH_PHY_SEL_x values. Move the FIELD_PREP() into sti_dwmac_set_mode(). Use dwmac->interface directly.

Signed-off-by Russell King (Oracle) <[email protected]>
---
 .../net/ethernet/stmicro/stmmac/dwmac-sti.c   | 27 +++++++++----------
 1 file changed, 12 insertions(+), 15 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c +12 -15
index 1e8769a81d77..c97535824be0 100644
@@ -81,11 +81,6 @@
  */
 #define MII_PHY_SEL_MASK	GENMASK(4, 2)
 #define MII_PHY_SEL_VAL(val)	FIELD_PREP_CONST(MII_PHY_SEL_MASK, val)
-#define ETH_PHY_SEL_RMII	MII_PHY_SEL_VAL(PHY_INTF_SEL_RMII)
-#define ETH_PHY_SEL_SGMII	MII_PHY_SEL_VAL(PHY_INTF_SEL_SGMII)
-#define ETH_PHY_SEL_RGMII	MII_PHY_SEL_VAL(PHY_INTF_SEL_RGMII)
-#define ETH_PHY_SEL_GMII	MII_PHY_SEL_VAL(PHY_INTF_SEL_GMII_MII)
-#define ETH_PHY_SEL_MII		MII_PHY_SEL_VAL(PHY_INTF_SEL_GMII_MII)
 
 struct sti_dwmac {
 	phy_interface_t interface;	/* MII interface */

@@ -104,13 +99,13 @@ struct sti_dwmac_of_data {
 	void (*fix_retime_src)(void *priv, int speed, unsigned int mode);
 };
 
-static u32 phy_intf_sels[] = {
-	[PHY_INTERFACE_MODE_MII] = ETH_PHY_SEL_MII,
-	[PHY_INTERFACE_MODE_GMII] = ETH_PHY_SEL_GMII,
-	[PHY_INTERFACE_MODE_RGMII] = ETH_PHY_SEL_RGMII,
-	[PHY_INTERFACE_MODE_RGMII_ID] = ETH_PHY_SEL_RGMII,
-	[PHY_INTERFACE_MODE_SGMII] = ETH_PHY_SEL_SGMII,
-	[PHY_INTERFACE_MODE_RMII] = ETH_PHY_SEL_RMII,
+static u8 phy_intf_sels[] = {
+	[PHY_INTERFACE_MODE_MII] = PHY_INTF_SEL_GMII_MII,
+	[PHY_INTERFACE_MODE_GMII] = PHY_INTF_SEL_GMII_MII,
+	[PHY_INTERFACE_MODE_RGMII] = PHY_INTF_SEL_RGMII,
+	[PHY_INTERFACE_MODE_RGMII_ID] = PHY_INTF_SEL_RGMII,
+	[PHY_INTERFACE_MODE_SGMII] = PHY_INTF_SEL_SGMII,
+	[PHY_INTERFACE_MODE_RMII] = PHY_INTF_SEL_RMII,
 };
 
 enum {

@@ -164,16 +159,18 @@ static void stih4xx_fix_retime_src(void *priv, int spd, unsigned int mode)
 static int sti_dwmac_set_mode(struct sti_dwmac *dwmac)
 {
 	struct regmap *regmap = dwmac->regmap;
-	int iface = dwmac->interface;
 	u32 reg = dwmac->ctrl_reg;
+	u8 phy_intf_sel;
 	u32 val;
 
 	if (dwmac->gmac_en)
 		regmap_update_bits(regmap, reg, EN_MASK, EN);
 
-	regmap_update_bits(regmap, reg, MII_PHY_SEL_MASK, phy_intf_sels[iface]);
+	phy_intf_sel = phy_intf_sels[dwmac->interface];
+	regmap_update_bits(regmap, reg, MII_PHY_SEL_MASK,
+			   FIELD_PREP(MII_PHY_SEL_MASK, phy_intf_sel));
 
-	val = (iface == PHY_INTERFACE_MODE_REVMII) ? 0 : ENMII;
+	val = (dwmac->interface == PHY_INTERFACE_MODE_REVMII) ? 0 : ENMII;
 	regmap_update_bits(regmap, reg, ENMII_MASK, val);
 
 	dwmac->fix_retime_src(dwmac, dwmac->speed, 0);
Signature · 1 line
2.47.3
#8 lore raw

PATCH 8/9 net: stmmac: sti: use stmmac_get_phy_intf_sel()

In reply to Russell King (Oracle)

Use stmmac_get_phy_intf_sel() to decode the PHY interface mode to the phy_intf_sel value, validate the result and use that to set the control register to select the operating mode for the DWMAC core.

Note that when an unsupported interface mode is used, the array would decode this to PHY_INTF_SEL_GMII_MII, so preserve this behaviour.

Signed-off-by Russell King (Oracle) <[email protected]>
---
 .../net/ethernet/stmicro/stmmac/dwmac-sti.c   | 22 ++++++++-----------
 1 file changed, 9 insertions(+), 13 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c +9 -13
index c97535824be0..593e154b5957 100644
@@ -77,10 +77,9 @@
  *	001-RGMII
  *	010-SGMII
  *	100-RMII
- * These are the DW MAC phy_intf_sel values
+ * These are the DW MAC phy_intf_sel values.
  */
 #define MII_PHY_SEL_MASK	GENMASK(4, 2)
-#define MII_PHY_SEL_VAL(val)	FIELD_PREP_CONST(MII_PHY_SEL_MASK, val)
 
 struct sti_dwmac {
 	phy_interface_t interface;	/* MII interface */

@@ -99,15 +98,6 @@ struct sti_dwmac_of_data {
 	void (*fix_retime_src)(void *priv, int speed, unsigned int mode);
 };
 
-static u8 phy_intf_sels[] = {
-	[PHY_INTERFACE_MODE_MII] = PHY_INTF_SEL_GMII_MII,
-	[PHY_INTERFACE_MODE_GMII] = PHY_INTF_SEL_GMII_MII,
-	[PHY_INTERFACE_MODE_RGMII] = PHY_INTF_SEL_RGMII,
-	[PHY_INTERFACE_MODE_RGMII_ID] = PHY_INTF_SEL_RGMII,
-	[PHY_INTERFACE_MODE_SGMII] = PHY_INTF_SEL_SGMII,
-	[PHY_INTERFACE_MODE_RMII] = PHY_INTF_SEL_RMII,
-};
-
 enum {
 	TX_RETIME_SRC_NA = 0,
 	TX_RETIME_SRC_TXCLK = 1,

@@ -160,13 +150,19 @@ static int sti_dwmac_set_mode(struct sti_dwmac *dwmac)
 {
 	struct regmap *regmap = dwmac->regmap;
 	u32 reg = dwmac->ctrl_reg;
-	u8 phy_intf_sel;
+	int phy_intf_sel;
 	u32 val;
 
 	if (dwmac->gmac_en)
 		regmap_update_bits(regmap, reg, EN_MASK, EN);
 
-	phy_intf_sel = phy_intf_sels[dwmac->interface];
+	phy_intf_sel = stmmac_get_phy_intf_sel(dwmac->interface);
+	if (phy_intf_sel != PHY_INTF_SEL_GMII_MII &&
+	    phy_intf_sel != PHY_INTF_SEL_RGMII &&
+	    phy_intf_sel != PHY_INTF_SEL_SGMII &&
+	    phy_intf_sel != PHY_INTF_SEL_RMII)
+		phy_intf_sel = PHY_INTF_SEL_GMII_MII;
+
 	regmap_update_bits(regmap, reg, MII_PHY_SEL_MASK,
 			   FIELD_PREP(MII_PHY_SEL_MASK, phy_intf_sel));
Signature · 1 line
2.47.3
#9 lore raw

PATCH 9/9 net: stmmac: sti: use ->set_phy_intf_sel()

In reply to Russell King (Oracle)

Rather than placing the phy_intf_sel() setup in the ->init() method, move it to the new ->set_phy_intf_sel() method.

Signed-off-by Russell King (Oracle) <[email protected]>
---
 .../net/ethernet/stmicro/stmmac/dwmac-sti.c   | 25 +++++++------------
 1 file changed, 9 insertions(+), 16 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c +9 -16
index 593e154b5957..b0509ab6b31c 100644
@@ -146,17 +146,18 @@ static void stih4xx_fix_retime_src(void *priv, int spd, unsigned int mode)
 			   stih4xx_tx_retime_val[src]);
 }
 
-static int sti_dwmac_set_mode(struct sti_dwmac *dwmac)
+static int sti_set_phy_intf_sel(void *bsp_priv, u8 phy_intf_sel)
 {
-	struct regmap *regmap = dwmac->regmap;
-	u32 reg = dwmac->ctrl_reg;
-	int phy_intf_sel;
-	u32 val;
+	struct sti_dwmac *dwmac = bsp_priv;
+	struct regmap *regmap;
+	u32 reg, val;
+
+	regmap = dwmac->regmap;
+	reg = dwmac->ctrl_reg;
 
 	if (dwmac->gmac_en)
 		regmap_update_bits(regmap, reg, EN_MASK, EN);
 
-	phy_intf_sel = stmmac_get_phy_intf_sel(dwmac->interface);
 	if (phy_intf_sel != PHY_INTF_SEL_GMII_MII &&
 	    phy_intf_sel != PHY_INTF_SEL_RGMII &&
 	    phy_intf_sel != PHY_INTF_SEL_SGMII &&

@@ -231,17 +232,8 @@ static int sti_dwmac_parse_data(struct sti_dwmac *dwmac,
 static int sti_dwmac_init(struct platform_device *pdev, void *bsp_priv)
 {
 	struct sti_dwmac *dwmac = bsp_priv;
-	int ret;
-
-	ret = clk_prepare_enable(dwmac->clk);
-	if (ret)
-		return ret;
-
-	ret = sti_dwmac_set_mode(dwmac);
-	if (ret)
-		clk_disable_unprepare(dwmac->clk);
 
-	return ret;
+	return clk_prepare_enable(dwmac->clk);
 }
 
 static void sti_dwmac_exit(struct platform_device *pdev, void *bsp_priv)

@@ -286,6 +278,7 @@ static int sti_dwmac_probe(struct platform_device *pdev)
 	dwmac->fix_retime_src = data->fix_retime_src;
 
 	plat_dat->bsp_priv = dwmac;
+	plat_dat->set_phy_intf_sel = sti_set_phy_intf_sel;
 	plat_dat->fix_mac_speed = data->fix_retime_src;
 	plat_dat->init = sti_dwmac_init;
 	plat_dat->exit = sti_dwmac_exit;
Signature · 1 line
2.47.3
CI Applied
#10 lore raw
In reply to Russell King (Oracle)
This series was applied to netdev/net-next.git (main) by Jakub Kicinski <[email protected]>:

Hello:

This series was applied to netdev/net-next.git (main) by Jakub Kicinski <[email protected]>:

Quoted 6 lines · On Thu, 6 Nov 2025 11:21:23 +0000 you wrote:

This series converts lpc18xx and sti to use the new .set_phy_intf_sel() method.

 .../net/ethernet/stmicro/stmmac/dwmac-lpc18xx.c    | 42 ++++++++++--------
 drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c    | 50 ++++++++--------------
 2 files changed, 42 insertions(+), 50 deletions(-)

Here is the summary with links:
- [net-next,1/9] net: stmmac: lpc18xx: convert to PHY_INTF_SEL_x

    https://git.kernel.org/netdev/net-next/c/5636fcdb0211
  - [net-next,2/9] net: stmmac: lpc18xx: use PHY_INTF_SEL_x directly
    https://git.kernel.org/netdev/net-next/c/eb0533c7e63b
  - [net-next,3/9] net: stmmac: lpc18xx: use stmmac_get_phy_intf_sel()
    https://git.kernel.org/netdev/net-next/c/9882f1219408
  - [net-next,4/9] net: stmmac: lpc18xx: validate phy_intf_sel
    https://git.kernel.org/netdev/net-next/c/4bad4219249f
  - [net-next,5/9] net: stmmac: lpc18xx: use ->set_phy_intf_sel()
    https://git.kernel.org/netdev/net-next/c/7fe0e06a7364
  - [net-next,6/9] net: stmmac: sti: use PHY_INTF_SEL_x to select PHY interface
    https://git.kernel.org/netdev/net-next/c/9cd23c02ac57
  - [net-next,7/9] net: stmmac: sti: use PHY_INTF_SEL_x directly
    https://git.kernel.org/netdev/net-next/c/bd5a68159259
  - [net-next,8/9] net: stmmac: sti: use stmmac_get_phy_intf_sel()
    https://git.kernel.org/netdev/net-next/c/ef5e870be90f
  - [net-next,9/9] net: stmmac: sti: use ->set_phy_intf_sel()
    https://git.kernel.org/netdev/net-next/c/e3c8f25cf2aa

You are awesome, thank you!

Signature · 2 lines
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html