Skip to contentSkip to conversation

mmc: meson-gx: minor improvements in meson_mmc_set_ios

PATCH New Heiner Kallweit 2 participants 12 messages Feb 1, 2017 – Feb 3, 2017 1 message not in the archive

Subsystems (2)
lore
Share & tools
lore

A message that is not in the archive (sent off-list or not yet received): [email protected]

#1 lore raw

PATCH v2 2/9 mmc: meson-gx: minor improvements in meson_mmc_set_ios

val isn't used in the switch clause and afterwards there's an identical statement. So remove it.

In case of an unexpected bus width the error message indicates the intention to set the bus width to 4 and to go on. So remove the return statement. This return statement also conflicts with "setting to 4" because nothing would be set actually before returning.

---
v2:
- added acked-by

---
 drivers/mmc/host/meson-gx-mmc.c | 2 --
 1 file changed, 2 deletions(-)
drivers/mmc/host/meson-gx-mmc.c +0 -2
index da3cce31..38edc60d 100644
@@ -379,7 +379,6 @@ static void meson_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 	meson_mmc_clk_set(host, ios->clock);
 
 	/* Bus width */
-	val = readl(host->regs + SD_EMMC_CFG);
 	switch (ios->bus_width) {
 	case MMC_BUS_WIDTH_1:
 		bus_width = CFG_BUS_WIDTH_1;
@@ -394,7 +393,6 @@ static void meson_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 		dev_err(host->dev, "Invalid ios->bus_width: %u.  Setting to 4.\n",
 			ios->bus_width);
 		bus_width = CFG_BUS_WIDTH_4;
-		return;
 	}
 
 	val = readl(host->regs + SD_EMMC_CFG);
Signature · 1 line
2.11.0
#2 lore raw

PATCH v2 3/9 mmc: meson-gx: improve meson_mmc_clk_set

In reply to a message not in the archive

The following changes are quite small, therefore I combined them in one patch.

- ret doesn't need to be initialized with 0
- use standard !clk_rate notation to check for a zero value
- If clk_rate is zero we return here. Therefore all further checks in this function for clk_rate != 0 are not needed.
- switch from dev_warn to dev_err if the clock can't be set
- If due to clock source and available divider values the requested frequency isn't matched exactly (always the case if requested frequency is 52 MHz), then just print the differing values as debug message and not as warning.
- Also remove ret from the message as it is always 0.
- In the case of actual frequency not exactly matching the requested one set mmc->actual_clock to the requested frequency. So far mmc->actual_clock wasn't set at all in this case.

---
v2:
- added reviewed by, tested-by

---
 drivers/mmc/host/meson-gx-mmc.c | 36 +++++++++++++++++++-----------------
 1 file changed, 19 insertions(+), 17 deletions(-)
drivers/mmc/host/meson-gx-mmc.c +19 -17
index 38edc60d..529a4f22 100644
@@ -179,7 +179,7 @@ struct sd_emmc_desc {
 static int meson_mmc_clk_set(struct meson_host *host, unsigned long clk_rate)
 {
 	struct mmc_host *mmc = host->mmc;
-	int ret = 0;
+	int ret;
 	u32 cfg;
 
 	if (clk_rate) {
@@ -202,29 +202,31 @@ static int meson_mmc_clk_set(struct meson_host *host, unsigned long clk_rate)
 	dev_dbg(host->dev, "change clock rate %u -> %lu\n",
 		mmc->actual_clock, clk_rate);
 
-	if (clk_rate == 0) {
+	if (!clk_rate) {
 		mmc->actual_clock = 0;
 		return 0;
 	}
 
 	ret = clk_set_rate(host->cfg_div_clk, clk_rate);
-	if (ret)
-		dev_warn(host->dev, "Unable to set cfg_div_clk to %lu. ret=%d\n",
-			 clk_rate, ret);
-	else if (clk_rate && clk_rate != clk_get_rate(host->cfg_div_clk))
-		dev_warn(host->dev, "divider requested rate %lu != actual rate %lu: ret=%d\n",
-			 clk_rate, clk_get_rate(host->cfg_div_clk), ret);
-	else
-		mmc->actual_clock = clk_rate;
-
-	/* (re)start clock, if non-zero */
-	if (!ret && clk_rate) {
-		cfg = readl(host->regs + SD_EMMC_CFG);
-		cfg &= ~CFG_STOP_CLOCK;
-		writel(cfg, host->regs + SD_EMMC_CFG);
+	if (ret) {
+		dev_err(host->dev, "Unable to set cfg_div_clk to %lu. ret=%d\n",
+			clk_rate, ret);
+		return ret;
 	}
 
-	return ret;
+	if (clk_rate != clk_get_rate(host->cfg_div_clk))
+		dev_dbg(host->dev,
+			"divider requested rate %lu != actual rate %lu\n",
+			clk_rate, clk_get_rate(host->cfg_div_clk));
+
+	mmc->actual_clock = clk_rate;
+
+	/* (re)start clock */
+	cfg = readl(host->regs + SD_EMMC_CFG);
+	cfg &= ~CFG_STOP_CLOCK;
+	writel(cfg, host->regs + SD_EMMC_CFG);
+
+	return 0;
 }
 
 /*
Signature · 1 line
2.11.0
#3 lore raw

PATCH v2 4/9 mmc: meson-gx: improve meson_mmc_irq_thread

In reply to a message not in the archive

Remove unneeded variable ret and simplify the if block.

---
v2:
- no changes

---
 drivers/mmc/host/meson-gx-mmc.c | 15 ++++++---------
 1 file changed, 6 insertions(+), 9 deletions(-)
drivers/mmc/host/meson-gx-mmc.c +6 -9
index 529a4f22..4ce4c640 100644
@@ -670,7 +670,6 @@ static irqreturn_t meson_mmc_irq_thread(int irq, void *dev_id)
 	struct mmc_command *cmd = host->cmd;
 	struct mmc_data *data;
 	unsigned int xfer_bytes;
-	int ret = IRQ_HANDLED;
 
 	if (WARN_ON(!mrq))
 		return IRQ_NONE;
@@ -679,14 +678,12 @@ static irqreturn_t meson_mmc_irq_thread(int irq, void *dev_id)
 		return IRQ_NONE;
 
 	data = cmd->data;
-	if (data) {
+	if (data && data->flags & MMC_DATA_READ) {
 		xfer_bytes = data->blksz * data->blocks;
-		if (data->flags & MMC_DATA_READ) {
-			WARN_ON(xfer_bytes > host->bounce_buf_size);
-			sg_copy_from_buffer(data->sg, data->sg_len,
-					    host->bounce_buf, xfer_bytes);
-			data->bytes_xfered = xfer_bytes;
-		}
+		WARN_ON(xfer_bytes > host->bounce_buf_size);
+		sg_copy_from_buffer(data->sg, data->sg_len,
+				    host->bounce_buf, xfer_bytes);
+		data->bytes_xfered = xfer_bytes;
 	}
 
 	meson_mmc_read_resp(host->mmc, cmd);
@@ -695,7 +692,7 @@ static irqreturn_t meson_mmc_irq_thread(int irq, void *dev_id)
 	else
 		meson_mmc_start_cmd(host->mmc, data->stop);
 
-	return ret;
+	return IRQ_HANDLED;
 }
 
 /*
Signature · 1 line
2.11.0
maintainer
#4 lore raw

PATCH v2 4/9 mmc: meson-gx: improve meson_mmc_irq_thread

Quoted 6 lines · Heiner Kallweit

Remove unneeded variable ret and simplify the if block.

---
v2:
- no changes

Quoted 45 lines
---
 drivers/mmc/host/meson-gx-mmc.c | 15 ++++++---------
 1 file changed, 6 insertions(+), 9 deletions(-)
drivers/mmc/host/meson-gx-mmc.c +6 -9
index 529a4f22..4ce4c640 100644
@@ -670,7 +670,6 @@ static irqreturn_t meson_mmc_irq_thread(int irq, void *dev_id)
 	struct mmc_command *cmd = host->cmd;
 	struct mmc_data *data;
 	unsigned int xfer_bytes;
-	int ret = IRQ_HANDLED;
 
 	if (WARN_ON(!mrq))
 		return IRQ_NONE;
@@ -679,14 +678,12 @@ static irqreturn_t meson_mmc_irq_thread(int irq, void *dev_id)
 		return IRQ_NONE;
 
 	data = cmd->data;
-	if (data) {
+	if (data && data->flags & MMC_DATA_READ) {
 		xfer_bytes = data->blksz * data->blocks;
-		if (data->flags & MMC_DATA_READ) {
-			WARN_ON(xfer_bytes > host->bounce_buf_size);
-			sg_copy_from_buffer(data->sg, data->sg_len,
-					    host->bounce_buf, xfer_bytes);
-			data->bytes_xfered = xfer_bytes;
-		}
+		WARN_ON(xfer_bytes > host->bounce_buf_size);
+		sg_copy_from_buffer(data->sg, data->sg_len,
+				    host->bounce_buf, xfer_bytes);
+		data->bytes_xfered = xfer_bytes;
 	}
 
 	meson_mmc_read_resp(host->mmc, cmd);
@@ -695,7 +692,7 @@ static irqreturn_t meson_mmc_irq_thread(int irq, void *dev_id)
 	else
 		meson_mmc_start_cmd(host->mmc, data->stop);
 
-	return ret;
+	return IRQ_HANDLED;
 }
 
 /*
#5 lore raw

PATCH v2 5/9 mmc: meson-gx: improve interrupt handling

In reply to a message not in the archive

Disabling and immediately re-enabling interrupts in meson_mmc_request doesn't provide a benefit. Instead enable interrupts in probe already. And disable interrupts in remove, this was missing so far.

---
v2:
- no changes

---
 drivers/mmc/host/meson-gx-mmc.c | 10 ++++------
 1 file changed, 4 insertions(+), 6 deletions(-)
drivers/mmc/host/meson-gx-mmc.c +4 -6
index 4ce4c640..0fba23d2 100644
@@ -546,11 +546,6 @@ static void meson_mmc_request(struct mmc_host *mmc, struct mmc_request *mrq)
 	/* Stop execution */
 	writel(0, host->regs + SD_EMMC_START);
 
-	/* clear, ack, enable all interrupts */
-	writel(0, host->regs + SD_EMMC_IRQ_EN);
-	writel(IRQ_EN_MASK, host->regs + SD_EMMC_STATUS);
-	writel(IRQ_EN_MASK, host->regs + SD_EMMC_IRQ_EN);
-
 	host->mrq = mrq;
 
 	if (mrq->sbc)
@@ -777,8 +772,8 @@ static int meson_mmc_probe(struct platform_device *pdev)
 	writel(0, host->regs + SD_EMMC_START);
 
 	/* clear, ack, enable all interrupts */
-	writel(0, host->regs + SD_EMMC_IRQ_EN);
 	writel(IRQ_EN_MASK, host->regs + SD_EMMC_STATUS);
+	writel(IRQ_EN_MASK, host->regs + SD_EMMC_IRQ_EN);
 
 	ret = devm_request_threaded_irq(&pdev->dev, host->irq,
 					meson_mmc_irq, meson_mmc_irq_thread,
@@ -816,6 +811,9 @@ static int meson_mmc_remove(struct platform_device *pdev)
 	if (WARN_ON(!host))
 		return 0;
 
+	/* disable interrupts */
+	writel(0, host->regs + SD_EMMC_IRQ_EN);
+
 	if (host->bounce_buf)
 		dma_free_coherent(host->dev, host->bounce_buf_size,
 				  host->bounce_buf, host->bounce_dma_addr);
Signature · 1 line
2.11.0
maintainer
#6 lore raw

PATCH v2 5/9 mmc: meson-gx: improve interrupt handling

Quoted 5 lines · Heiner Kallweit

Disabling and immediately re-enabling interrupts in meson_mmc_request doesn't provide a benefit. Instead enable interrupts in probe already. And disable interrupts in remove, this was missing so far.

This isn't quite functionaly equivalent...

Quoted 24 lines

---
v2:
- no changes

---
 drivers/mmc/host/meson-gx-mmc.c | 10 ++++------
 1 file changed, 4 insertions(+), 6 deletions(-)
drivers/mmc/host/meson-gx-mmc.c +0 -5
index 4ce4c640..0fba23d2 100644
@@ -546,11 +546,6 @@ static void meson_mmc_request(struct mmc_host *mmc, struct mmc_request *mrq)
 	/* Stop execution */
 	writel(0, host->regs + SD_EMMC_START);
 
-	/* clear, ack, enable all interrupts */
-	writel(0, host->regs + SD_EMMC_IRQ_EN);
-	writel(IRQ_EN_MASK, host->regs + SD_EMMC_STATUS);
-	writel(IRQ_EN_MASK, host->regs + SD_EMMC_IRQ_EN);
-
 	host->mrq = mrq;
 
 	if (mrq->sbc)

drivers/mmc/host/meson-gx-mmc.c static int meson_mmc_probe(struct platform_device *pdev) · line 780

Quoted 4 lines
drivers/mmc/host/meson-gx-mmc.c +0 -1
@@ -777,8 +772,8 @@ static int meson_mmc_probe(struct platform_device *pdev)
 	writel(0, host->regs + SD_EMMC_START);
 
 	/* clear, ack, enable all interrupts */
-	writel(0, host->regs + SD_EMMC_IRQ_EN);

I'm not sure about this part. Without the "disable all" here...

drivers/mmc/host/meson-gx-mmc.c static int meson_mmc_probe(struct platform_device *pdev) · line 775

Quoted 1 line
drivers/mmc/host/meson-gx-mmc.c +0 -0
 	writel(IRQ_EN_MASK, host->regs + SD_EMMC_STATUS);

... this ack could cause an interrupt to fire, if one was pending based on boot firmware activity. I did notice this during driver development on some boards, which is why the "disable all" was added.

That may have been an artifact of a buggy driver during development, but I left it in anyways.

Quoted 5 lines
drivers/mmc/host/meson-gx-mmc.c +1 -0
+	writel(IRQ_EN_MASK, host->regs + SD_EMMC_IRQ_EN);
 
 	ret = devm_request_threaded_irq(&pdev->dev, host->irq,
 					meson_mmc_irq, meson_mmc_irq_thread,

drivers/mmc/host/meson-gx-mmc.c static int meson_mmc_remove(struct platform_device *pdev) · line 819

Quoted 9 lines
drivers/mmc/host/meson-gx-mmc.c +3 -0
@@ -816,6 +811,9 @@ static int meson_mmc_remove(struct platform_device *pdev)
 	if (WARN_ON(!host))
 		return 0;
 
+	/* disable interrupts */
+	writel(0, host->regs + SD_EMMC_IRQ_EN);
+
 	if (host->bounce_buf)
 		dma_free_coherent(host->dev, host->bounce_buf_size,
 				  host->bounce_buf, host->bounce_dma_addr);

Other than the nit above, the rest of the cleanup looks fine.

If you leave in the "disable all" during probe,

Kevin

#7 lore raw

PATCH v2 6/9 mmc: meson-gx: set max block count and request size

In reply to a message not in the archive

So far max_blk_count isn't set what results in a default of value 8 to be used (PAGE_SIZE / block size).

Block length field has 9 bits, so set max_blk_count to 2^9-1 = 511. In addition set max_req_size because max_blk_count is also limited by max_req_size / block_size.

---
v2:
- added reviewed-by, tested-by, acked-by

---
 drivers/mmc/host/meson-gx-mmc.c | 3 +++
 1 file changed, 3 insertions(+)
drivers/mmc/host/meson-gx-mmc.c +3 -0
index 0fba23d2..883263c5 100644
@@ -781,6 +781,9 @@ static int meson_mmc_probe(struct platform_device *pdev)
 	if (ret)
 		goto free_host;
 
+	mmc->max_blk_count = CMD_CFG_LENGTH_MASK;
+	mmc->max_req_size = mmc->max_blk_count * mmc->max_blk_size;
+
 	/* data bounce buffer */
 	host->bounce_buf_size = SZ_512K;
 	host->bounce_buf =
Signature · 1 line
2.11.0
#8 lore raw

PATCH v2 7/9 mmc: meson-gx: reduce bounce buffer size

In reply to a message not in the archive

A bounce buffer of 512K isn't needed as the max request size is 511 * 512 byte.

---
v2:
- no changes

---
 drivers/mmc/host/meson-gx-mmc.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/mmc/host/meson-gx-mmc.c +1 -1
index 883263c5..48ce4ba4 100644
@@ -785,7 +785,7 @@ static int meson_mmc_probe(struct platform_device *pdev)
 	mmc->max_req_size = mmc->max_blk_count * mmc->max_blk_size;
 
 	/* data bounce buffer */
-	host->bounce_buf_size = SZ_512K;
+	host->bounce_buf_size = mmc->max_req_size;
 	host->bounce_buf =
 		dma_alloc_coherent(host->dev, host->bounce_buf_size,
 				   &host->bounce_dma_addr, GFP_KERNEL);
Signature · 1 line
2.11.0
maintainer
#9 lore raw

PATCH v2 7/9 mmc: meson-gx: reduce bounce buffer size

Quoted 4 lines · Heiner Kallweit

A bounce buffer of 512K isn't needed as the max request size is 511 * 512 byte.

Quoted 20 lines

---
v2:
- no changes

---
 drivers/mmc/host/meson-gx-mmc.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/mmc/host/meson-gx-mmc.c +1 -1
index 883263c5..48ce4ba4 100644
@@ -785,7 +785,7 @@ static int meson_mmc_probe(struct platform_device *pdev)
 	mmc->max_req_size = mmc->max_blk_count * mmc->max_blk_size;
 
 	/* data bounce buffer */
-	host->bounce_buf_size = SZ_512K;
+	host->bounce_buf_size = mmc->max_req_size;
 	host->bounce_buf =
 		dma_alloc_coherent(host->dev, host->bounce_buf_size,
 				   &host->bounce_dma_addr, GFP_KERNEL);
#10 lore raw

PATCH v2 8/9 mmc: meson-gx: remove unneeded checks in remove

In reply to a message not in the archive

The remove callback is called only if probe finished successfully. Therefore these checks are not needed.

---
v2:
- no changes

---
 drivers/mmc/host/meson-gx-mmc.c | 8 ++------
 1 file changed, 2 insertions(+), 6 deletions(-)
drivers/mmc/host/meson-gx-mmc.c +2 -6
index 48ce4ba4..bc787444 100644
@@ -811,15 +811,11 @@ static int meson_mmc_remove(struct platform_device *pdev)
 {
 	struct meson_host *host = dev_get_drvdata(&pdev->dev);
 
-	if (WARN_ON(!host))
-		return 0;
-
 	/* disable interrupts */
 	writel(0, host->regs + SD_EMMC_IRQ_EN);
 
-	if (host->bounce_buf)
-		dma_free_coherent(host->dev, host->bounce_buf_size,
-				  host->bounce_buf, host->bounce_dma_addr);
+	dma_free_coherent(host->dev, host->bounce_buf_size,
+			  host->bounce_buf, host->bounce_dma_addr);
 
 	clk_disable_unprepare(host->cfg_div_clk);
 	clk_disable_unprepare(host->core_clk);
Signature · 1 line
2.11.0
maintainer
#11 lore raw

PATCH v2 8/9 mmc: meson-gx: remove unneeded checks in remove

Quoted 4 lines · Heiner Kallweit

The remove callback is called only if probe finished successfully. Therefore these checks are not needed.

Quoted 29 lines

---
v2:
- no changes

---
 drivers/mmc/host/meson-gx-mmc.c | 8 ++------
 1 file changed, 2 insertions(+), 6 deletions(-)
drivers/mmc/host/meson-gx-mmc.c +2 -6
index 48ce4ba4..bc787444 100644
@@ -811,15 +811,11 @@ static int meson_mmc_remove(struct platform_device *pdev)
 {
 	struct meson_host *host = dev_get_drvdata(&pdev->dev);
 
-	if (WARN_ON(!host))
-		return 0;
-
 	/* disable interrupts */
 	writel(0, host->regs + SD_EMMC_IRQ_EN);
 
-	if (host->bounce_buf)
-		dma_free_coherent(host->dev, host->bounce_buf_size,
-				  host->bounce_buf, host->bounce_dma_addr);
+	dma_free_coherent(host->dev, host->bounce_buf_size,
+			  host->bounce_buf, host->bounce_dma_addr);
 
 	clk_disable_unprepare(host->cfg_div_clk);
 	clk_disable_unprepare(host->core_clk);
#12 lore raw

PATCH v2 9/9 mmc: meson-gx: add support for HS400 mode

In reply to a message not in the archive

Add support for HS400 mode.

Successfully tested on a Odroid C2 (S905 GXBB).

---
v2:
- added reviewed-by, tested-by

---
 drivers/mmc/host/meson-gx-mmc.c | 11 +++++++++++
 1 file changed, 11 insertions(+)
drivers/mmc/host/meson-gx-mmc.c +11 -0
index bc787444..83a94cf5 100644
@@ -83,6 +83,7 @@
 #define   CFG_RC_CC_MASK 0xf
 #define   CFG_STOP_CLOCK BIT(22)
 #define   CFG_CLK_ALWAYS_ON BIT(18)
+#define   CFG_CHK_DS BIT(20)
 #define   CFG_AUTO_CLK BIT(23)
 
 #define SD_EMMC_STATUS 0x48
@@ -412,6 +413,16 @@ static void meson_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 	val &= ~(CFG_RC_CC_MASK << CFG_RC_CC_SHIFT);
 	val |= ilog2(SD_EMMC_CFG_CMD_GAP) << CFG_RC_CC_SHIFT;
 
+	val &= ~CFG_DDR;
+	if (ios->timing == MMC_TIMING_UHS_DDR50 ||
+	    ios->timing == MMC_TIMING_MMC_DDR52 ||
+	    ios->timing == MMC_TIMING_MMC_HS400)
+		val |= CFG_DDR;
+
+	val &= ~CFG_CHK_DS;
+	if (ios->timing == MMC_TIMING_MMC_HS400)
+		val |= CFG_CHK_DS;
+
 	writel(val, host->regs + SD_EMMC_CFG);
 
 	if (val != orig)
Signature · 1 line
2.11.0