LPC3250 periph clock at 13MHz instead of 10.4MHz
Hi,
I've been observing a mismatch between the reported periph clock frequency and the actuall periph clock frequency on a custom board.
clk_summary gives:
xtal 1 1 1 13000000 0 0 50000
osc 2 2 1 13000000 0 0 50000
sys 1 1 0 13000000 0 0 50000
hclk_pll 3 3 0 208000000 0 0 50000
hclk_div_periph 1 1 0 10400000 0 0 50000
sysclk_periph_mux 1 1 0 10400000 0 0 50000
pclk 4 4 0 10400000 0 0 50000
uart5 1 1 0 10400000 0 0 50000
timer0 1 1 0 10400000 0 0 50000
timer1 1 1 0 10400000 0 0 50000And this seems quite right when reading the registers using devmem.
But, I observed that the input clock for UART5 seems to be 13MHz. At 9600 bauds, the calculated UnDLM:UnDLL is 68 (which would give 10400000/(16*68) = 9558 bauds) but at the oscilloscope, I see that the UARt is running close to 12kHz. Forcing the frequency to 13MHz, gives a divisor of 85 and solves the issue.
Note that this issue will not be seen right away at 115200 bauds because the divisor is then quite close (6 for 10.4MHz and 7 for 13MHz).
Similarily using an i2c RTC, I can see that the timer is quite off:
# hwclock; sleep 10; hwclock
Tue Feb 12 16:53:09 2019 0.000000 seconds
Tue Feb 12 16:53:17 2019 0.000000 seconds
This is what is expected if the 13MHz input clock is mistaken as 10.4MHz as 10*10.4/13 = 8s.
This leads me to think that pclk is actually running at 13MHz.
PWR_CTRL is set to 0x16 so the pclk parent should be hclk_div and not sysclk.
Am I missing something?
Signature · 8 lines
Alexandre Belloni, Bootlin Embedded Linux and Kernel engineering https://bootlin.com _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Hi Alexandre,
Quoted 39 lines · Alexandre Belloni
Hi,
I've been observing a mismatch between the reported periph clock frequency and the actuall periph clock frequency on a custom board.
clk_summarygives:xtal 1 1 1 13000000 0 0 50000 osc 2 2 1 13000000 0 0 50000 sys 1 1 0 13000000 0 0 50000 hclk_pll 3 3 0 208000000 0 0 50000 hclk_div_periph 1 1 0 10400000 0 0 50000 sysclk_periph_mux 1 1 0 10400000 0 0 50000 pclk 4 4 0 10400000 0 0 50000 uart5 1 1 0 10400000 0 0 50000 timer0 1 1 0 10400000 0 0 50000 timer1 1 1 0 10400000 0 0 50000And this seems quite right when reading the registers using devmem.
But, I observed that the input clock for UART5 seems to be 13MHz. At 9600 bauds, the calculated UnDLM:UnDLL is 68 (which would give 10400000/(16*68) = 9558 bauds) but at the oscilloscope, I see that the UARt is running close to 12kHz. Forcing the frequency to 13MHz, gives a divisor of 85 and solves the issue.
Note that this issue will not be seen right away at 115200 bauds because the divisor is then quite close (6 for 10.4MHz and 7 for 13MHz).
Similarily using an i2c RTC, I can see that the timer is quite off:
# hwclock; sleep 10; hwclock
Tue Feb 12 16:53:09 2019 0.000000 seconds
Tue Feb 12 16:53:17 2019 0.000000 secondsThis is what is expected if the 13MHz input clock is mistaken as 10.4MHz as 10*10.4/13 = 8s.
Quoted 7 lines
This leads me to think that pclk is actually running at 13MHz.
PWR_CTRLis set to0x16so the pclk parent should behclk_divand not sysclk.Am I missing something?
I think I encountered quite a similar issue previously, but under another circumstances, when I begin to modify HCLK PLL clock rate, can you check my comment at https://lore.kernel.org/linux-clk/[email protected]/
and verify if it's about the same problem?
Since the problem hits you also, I plan to spend some time on this weekend to capture more details, fortunately there is a known workaround to pin UART input clock rate to 13MHz, it might be desired to carve it in the code.
Thank you for report.
--
Best wishes,
Vladimir
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Hi Vladimir,
Quoted 12 lines · Vladimir Zapolskiy
Quoted 2 lines
Am I missing something?
I think I encountered quite a similar issue previously, but under another circumstances, when I begin to modify HCLK PLL clock rate, can you check my comment at https://lore.kernel.org/linux-clk/[email protected]/
and verify if it's about the same problem?Since the problem hits you also, I plan to spend some time on this weekend to capture more details, fortunately there is a known workaround to pin UART input clock rate to 13MHz, it might be desired to carve it in the code.
I'm pretty sure this is the same issue and that it doesn't only affect the UARTs but also timers.
The 2.6.27.8 kernel code would indicated that the timers are only driven by sysclk, that is either 13MHz from the oscillator or 13.008896 from PLL397. I'm wondering how many other peripherals are affected.
Signature · 8 lines
Alexandre Belloni, Bootlin Embedded Linux and Kernel engineering https://bootlin.com _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Quoted 16 lines · Alexandre Belloni
Hi Vladimir,
Quoted 12 lines · Vladimir Zapolskiy
Quoted 2 lines
Am I missing something?
I think I encountered quite a similar issue previously, but under another circumstances, when I begin to modify HCLK PLL clock rate, can you check my comment at https://lore.kernel.org/linux-clk/[email protected]/
and verify if it's about the same problem?Since the problem hits you also, I plan to spend some time on this weekend to capture more details, fortunately there is a known workaround to pin UART input clock rate to 13MHz, it might be desired to carve it in the code.
Quoted 7 lines
I'm pretty sure this is the same issue and that it doesn't only affect the UARTs but also timers.
The 2.6.27.8 kernel code would indicated that the timers are only driven by sysclk, that is either 13MHz from the oscillator or 13.008896 from PLL397. I'm wondering how many other peripherals are affected.
You'll note that this is also true for the watchdog, the driver has:
// NOTE - the driver only uses this value if it can't get the clock rate from the clk_ drivers
#define WDOG_COUNTER_RATE 13000000 /*the counter clock is 13 MHz fixed */
Signature · 8 lines
Alexandre Belloni, Bootlin Embedded Linux and Kernel engineering https://bootlin.com _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Quoted 25 lines · Alexandre Belloni
Quoted 16 lines · Alexandre Belloni
Hi Vladimir,
Quoted 12 lines · Vladimir Zapolskiy
Quoted 2 lines
Am I missing something?
I think I encountered quite a similar issue previously, but under another circumstances, when I begin to modify HCLK PLL clock rate, can you check my comment at https://lore.kernel.org/linux-clk/[email protected]/
and verify if it's about the same problem?Since the problem hits you also, I plan to spend some time on this weekend to capture more details, fortunately there is a known workaround to pin UART input clock rate to 13MHz, it might be desired to carve it in the code.
Quoted 7 lines
I'm pretty sure this is the same issue and that it doesn't only affect the UARTs but also timers.
The 2.6.27.8 kernel code would indicated that the timers are only driven by sysclk, that is either 13MHz from the oscillator or 13.008896 from PLL397. I'm wondering how many other peripherals are affected.
Quoted 5 lines
You'll note that this is also true for the watchdog, the driver has:
// NOTE - the driver only uses this value if it can't get the clock rate from the
clk_drivers
#defineWDOG_COUNTER_RATE13000000 /*the counter clock is 13 MHz fixed */
Ok, I went further. We have test points for tst_clk1 and tst_clk2 so I've put periph_clk on test_clk2. It is definitively running at 13MHz. I only have access to a 100MHz oscilloscope so measuring hclk is not great but it seems to be around 125MHz (I would guess 130MHz then) So I had a look at SCK on an i2c bus that is supposed to be running at 100kHz. It is actually at 120kHz.
My conclusion is that switching from 260MHz to 208MHz is not working as expected, I don't know why yet.
Signature · 8 lines
Alexandre Belloni, Bootlin Embedded Linux and Kernel engineering https://bootlin.com _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel