Skip to contentSkip to conversation

net: stmmac: qcom-ethqos: more cleanups

PATCH Superseded Russell King (Oracle) 3 participants 19 messages Mar 24 – Mar 27

Subsystems (6)
Networking Network drivers Arm Qualcomm mailing list Arm STM32 +2 more subsystems

v1 of 2 Superseded Latest is v2 →

lore
Share & tools
lore

Russell King (Oracle)

author
#0 lore raw

cover net: stmmac: qcom-ethqos: more cleanups

Further cleanups to qcom-ethqos, mainly concentrating on the RGMII code, making it clearer what the differences are for each speed, thus making the code more readable.

I'm still not really happy with this. The speed specific configuration remains split between ethqos_fix_mac_speed_rgmii() and ethqos_rgmii_macro_init(), where the latter is only ever called from the former. So, I think further work is needed here - maybe it needs restructuring into the various componenet parts of the RGMII block?

 .../ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c    | 218 ++++++++-------------
 1 file changed, 86 insertions(+), 132 deletions(-)
Signature · 2 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 80Mbps down 10Mbps up. Decent connectivity at last!
#1 lore raw

PATCH 1/15 net: stmmac: qcom-ethqos: remove ethqos_configure()

ethqos_configure() does nothing more than indirect via ethqos->configure_func, and is only called from ethqos_fix_mac_speed() just below. Move the indirect call into ethqos_fix_mac_speed().

Signed-off-by Russell King (Oracle) <[email protected]>
---
 drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c | 8 +-------
 1 file changed, 1 insertion(+), 7 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c +1 -7
index 3ccf20fdf52a..502f2b184a87 100644
@@ -623,18 +623,12 @@ static void ethqos_configure_sgmii(struct qcom_ethqos *ethqos,
 	ethqos_pcs_set_inband(priv, interface == PHY_INTERFACE_MODE_SGMII);
 }
 
-static void ethqos_configure(struct qcom_ethqos *ethqos,
-			     phy_interface_t interface, int speed)
-{
-	return ethqos->configure_func(ethqos, interface, speed);
-}
-
 static void ethqos_fix_mac_speed(void *priv, phy_interface_t interface,
 				 int speed, unsigned int mode)
 {
 	struct qcom_ethqos *ethqos = priv;
 
-	ethqos_configure(ethqos, interface, speed);
+	ethqos->configure_func(ethqos, interface, speed);
 }
 
 static int qcom_ethqos_serdes_powerup(struct net_device *ndev, void *priv)
Signature · 1 line
2.47.3
#2 lore raw

PATCH 2/15 net: stmmac: qcom-ethqos: pass ethqos to ethqos_pcs_set_inband()

In reply to Russell King (Oracle)

Rather than geting the stmmac_priv pointer in ethqos_configure_sgmii(), move it into ethqos_pcs_set_inband() and pass the struct qcom_ethqos pointer instead.

Signed-off-by Russell King (Oracle) <[email protected]>
---
 .../net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c    | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c +5 -5
index 502f2b184a87..b9cfcf32cebc 100644
@@ -590,8 +590,11 @@ static void ethqos_configure_rgmii(struct qcom_ethqos *ethqos,
 	ethqos_rgmii_macro_init(ethqos, speed);
 }
 
-static void ethqos_pcs_set_inband(struct stmmac_priv *priv, bool enable)
+static void ethqos_pcs_set_inband(struct qcom_ethqos *ethqos, bool enable)
 {
+	struct net_device *dev = platform_get_drvdata(ethqos->pdev);
+	struct stmmac_priv *priv = netdev_priv(dev);
+
 	stmmac_pcs_ctrl_ane(priv, enable, 0);
 }
 

@@ -601,9 +604,6 @@ static void ethqos_pcs_set_inband(struct stmmac_priv *priv, bool enable)
 static void ethqos_configure_sgmii(struct qcom_ethqos *ethqos,
 				   phy_interface_t interface, int speed)
 {
-	struct net_device *dev = platform_get_drvdata(ethqos->pdev);
-	struct stmmac_priv *priv = netdev_priv(dev);
-
 	switch (speed) {
 	case SPEED_2500:
 	case SPEED_1000:

@@ -620,7 +620,7 @@ static void ethqos_configure_sgmii(struct qcom_ethqos *ethqos,
 		break;
 	}
 
-	ethqos_pcs_set_inband(priv, interface == PHY_INTERFACE_MODE_SGMII);
+	ethqos_pcs_set_inband(ethqos, interface == PHY_INTERFACE_MODE_SGMII);
 }
 
 static void ethqos_fix_mac_speed(void *priv, phy_interface_t interface,
Signature · 1 line
2.47.3
#3 lore raw

PATCH 3/15 net: stmmac: qcom-ethqos: eliminate configure_func

In reply to Russell King (Oracle)

Since ethqos_fix_mac_speed() is called via a function pointer, and only indirects via the configure_func function pointer, eliminate this unnecessary indirection.

Signed-off-by Russell King (Oracle) <[email protected]>
---
 .../stmicro/stmmac/dwmac-qcom-ethqos.c        | 33 ++++++++-----------
 1 file changed, 14 insertions(+), 19 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c +14 -19
index b9cfcf32cebc..84f713ec8c28 100644
@@ -100,9 +100,6 @@ struct ethqos_emac_driver_data {
 struct qcom_ethqos {
 	struct platform_device *pdev;
 	void __iomem *rgmii_base;
-	void (*configure_func)(struct qcom_ethqos *ethqos,
-			       phy_interface_t interface, int speed);
-
 	struct clk *link_clk;
 	struct phy *serdes_phy;
 	phy_interface_t phy_mode;

@@ -521,13 +518,17 @@ static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos, int speed)
 	return 0;
 }
 
-static void ethqos_configure_rgmii(struct qcom_ethqos *ethqos,
-				   phy_interface_t interface, int speed)
+static void ethqos_fix_mac_speed_rgmii(void *bsp_priv,
+				       phy_interface_t interface, int speed,
+				       unsigned int mode)
 {
-	struct device *dev = &ethqos->pdev->dev;
+	struct qcom_ethqos *ethqos = bsp_priv;
+	struct device *dev;
 	unsigned int i;
 	u32 val;
 
+	dev = &ethqos->pdev->dev;
+
 	/* Reset to POR values and enable clk */
 	for (i = 0; i < ethqos->num_rgmii_por; i++)
 		rgmii_writel(ethqos, ethqos->rgmii_por[i].value,

@@ -601,9 +602,12 @@ static void ethqos_pcs_set_inband(struct qcom_ethqos *ethqos, bool enable)
 /* On interface toggle MAC registers gets reset.
  * Configure MAC block for SGMII on ethernet phy link up
  */
-static void ethqos_configure_sgmii(struct qcom_ethqos *ethqos,
-				   phy_interface_t interface, int speed)
+static void ethqos_fix_mac_speed_sgmii(void *bsp_priv,
+				       phy_interface_t interface, int speed,
+				       unsigned int mode)
 {
+	struct qcom_ethqos *ethqos = bsp_priv;
+
 	switch (speed) {
 	case SPEED_2500:
 	case SPEED_1000:

@@ -623,14 +627,6 @@ static void ethqos_configure_sgmii(struct qcom_ethqos *ethqos,
 	ethqos_pcs_set_inband(ethqos, interface == PHY_INTERFACE_MODE_SGMII);
 }
 
-static void ethqos_fix_mac_speed(void *priv, phy_interface_t interface,
-				 int speed, unsigned int mode)
-{
-	struct qcom_ethqos *ethqos = priv;
-
-	ethqos->configure_func(ethqos, interface, speed);
-}
-
 static int qcom_ethqos_serdes_powerup(struct net_device *ndev, void *priv)
 {
 	struct qcom_ethqos *ethqos = priv;

@@ -753,11 +749,11 @@ static int qcom_ethqos_probe(struct platform_device *pdev)
 	case PHY_INTERFACE_MODE_RGMII_ID:
 	case PHY_INTERFACE_MODE_RGMII_RXID:
 	case PHY_INTERFACE_MODE_RGMII_TXID:
-		ethqos->configure_func = ethqos_configure_rgmii;
+		plat_dat->fix_mac_speed = ethqos_fix_mac_speed_rgmii;
 		break;
 	case PHY_INTERFACE_MODE_2500BASEX:
 	case PHY_INTERFACE_MODE_SGMII:
-		ethqos->configure_func = ethqos_configure_sgmii;
+		plat_dat->fix_mac_speed = ethqos_fix_mac_speed_sgmii;
 		plat_dat->mac_finish = ethqos_mac_finish_serdes;
 		break;
 	default:

@@ -805,7 +801,6 @@ static int qcom_ethqos_probe(struct platform_device *pdev)
 
 	plat_dat->bsp_priv = ethqos;
 	plat_dat->set_clk_tx_rate = ethqos_set_clk_tx_rate;
-	plat_dat->fix_mac_speed = ethqos_fix_mac_speed;
 	plat_dat->dump_debug_regs = rgmii_dump;
 	plat_dat->ptp_clk_freq_config = ethqos_ptp_clk_freq_config;
 	plat_dat->core_type = DWMAC_CORE_GMAC4;
Signature · 1 line
2.47.3
reviewer
#4 lore raw

Re: [PATCH net-next 03/15] net: stmmac: qcom-ethqos: eliminate configure_func

Quoted 5 lines · Russell King (Oracle)

Since ethqos_fix_mac_speed() is called via a function pointer, and only indirects via the configure_func function pointer, eliminate this unnecessary indirection.

Signed-off-by Russell King (Oracle) <[email protected]>

...

Quoted 5 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c +0 -1
@@ -623,14 +627,6 @@ static void ethqos_configure_sgmii(struct qcom_ethqos *ethqos,
 	ethqos_pcs_set_inband(ethqos, interface == PHY_INTERFACE_MODE_SGMII);
 }
 
-static void ethqos_fix_mac_speed(void *priv, phy_interface_t interface,

drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c static void ethqos_configure_sgmii(struct qcom_ethqos *ethqos, · line 632

Quoted 10 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c +0 -7
-				 int speed, unsigned int mode)
-{
-	struct qcom_ethqos *ethqos = priv;
-
-	ethqos->configure_func(ethqos, interface, speed);
-}
-
 static int qcom_ethqos_serdes_powerup(struct net_device *ndev, void *priv)
 {
 	struct qcom_ethqos *ethqos = priv;

Hi Russell,

FYI, AI generated review reports that the comment in ethqos_clks_config() that references ethqos_fix_mac_speed() should also be updated.

...

author
#5 lore raw

Re: [PATCH net-next 03/15] net: stmmac: qcom-ethqos: eliminate configure_func

Quoted 27 lines · Simon Horman
Quoted 5 lines · Russell King (Oracle)

Since ethqos_fix_mac_speed() is called via a function pointer, and only indirects via the configure_func function pointer, eliminate this unnecessary indirection.

Signed-off-by Russell King (Oracle) <[email protected]>

...

Quoted 5 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c +0 -1
@@ -623,14 +627,6 @@ static void ethqos_configure_sgmii(struct qcom_ethqos *ethqos,
 	ethqos_pcs_set_inband(ethqos, interface == PHY_INTERFACE_MODE_SGMII);
 }
 
-static void ethqos_fix_mac_speed(void *priv, phy_interface_t interface,

drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c static void ethqos_configure_sgmii(struct qcom_ethqos *ethqos, · line 632

Quoted 10 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c +0 -7
-				 int speed, unsigned int mode)
-{
-	struct qcom_ethqos *ethqos = priv;
-
-	ethqos->configure_func(ethqos, interface, speed);
-}
-
 static int qcom_ethqos_serdes_powerup(struct net_device *ndev, void *priv)
 {
 	struct qcom_ethqos *ethqos = priv;

Hi Russell,

Quoted 2 lines

FYI, AI generated review reports that the comment in ethqos_clks_config() that references ethqos_fix_mac_speed() should also be updated.

Also already noted (yesterday).

I do keep an eye on patchwork for my own patches - I have a firefox tab permanently open for my patches in patchwork:

https://patchwork.kernel.org/project/netdevbpf/list/?submitter=165511

Thanks anyway.

Signature · 2 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 80Mbps down 10Mbps up. Decent connectivity at last!
reviewer
#6 lore raw

Re: [PATCH net-next 03/15] net: stmmac: qcom-ethqos: eliminate configure_func

Quoted 31 lines · Russell King (Oracle)
Quoted 27 lines · Simon Horman
Quoted 5 lines · Russell King (Oracle)

Since ethqos_fix_mac_speed() is called via a function pointer, and only indirects via the configure_func function pointer, eliminate this unnecessary indirection.

Signed-off-by Russell King (Oracle) <[email protected]>

...

Quoted 5 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c +0 -1
@@ -623,14 +627,6 @@ static void ethqos_configure_sgmii(struct qcom_ethqos *ethqos,
 	ethqos_pcs_set_inband(ethqos, interface == PHY_INTERFACE_MODE_SGMII);
 }
 
-static void ethqos_fix_mac_speed(void *priv, phy_interface_t interface,

drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c static void ethqos_configure_sgmii(struct qcom_ethqos *ethqos, · line 632

Quoted 10 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c +0 -7
-				 int speed, unsigned int mode)
-{
-	struct qcom_ethqos *ethqos = priv;
-
-	ethqos->configure_func(ethqos, interface, speed);
-}
-
 static int qcom_ethqos_serdes_powerup(struct net_device *ndev, void *priv)
 {
 	struct qcom_ethqos *ethqos = priv;

Hi Russell,

Quoted 2 lines

FYI, AI generated review reports that the comment in ethqos_clks_config() that references ethqos_fix_mac_speed() should also be updated.

Quoted 8 lines

Also already noted (yesterday).

I do keep an eye on patchwork for my own patches - I have a firefox tab permanently open for my patches in patchwork:

https://patchwork.kernel.org/project/netdevbpf/list/?submitter=165511

Thanks anyway.

Thanks, and sorry if you told me this before.
I'll try to remember and not spam you with these things going forward.

#7 lore raw

PATCH 4/15 net: stmmac: qcom-ethqos: move detection of invalid RGMII speed

In reply to Russell King (Oracle)

Move detection of invalid RGMII speeds (which will never be triggered) before the switch() to allow register modifications that are common to all speeds to be moved out of the switch.

Signed-off-by Russell King (Oracle) <[email protected]>
---
 drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c | 8 +++++---
 1 file changed, 5 insertions(+), 3 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c +5 -3
index 84f713ec8c28..7e389db40e8b 100644
@@ -397,6 +397,11 @@ static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos, int speed)
 	/* Select RGMII, write 0 to interface select */
 	rgmii_clrmask(ethqos, RGMII_CONFIG_INTF_SEL, RGMII_IO_MACRO_CONFIG);
 
+	if (speed != SPEED_1000 && speed != SPEED_100 && speed != SPEED_10) {
+		dev_err(dev, "Invalid speed %d\n", speed);
+		return -EINVAL;
+	}
+
 	switch (speed) {
 	case SPEED_1000:
 		rgmii_setmask(ethqos, RGMII_CONFIG_DDR_MODE,

@@ -510,9 +515,6 @@ static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos, int speed)
 		rgmii_updatel(ethqos, RGMII_CONFIG_LOOPBACK_EN,
 			      loopback, RGMII_IO_MACRO_CONFIG);
 		break;
-	default:
-		dev_err(dev, "Invalid speed %d\n", speed);
-		return -EINVAL;
 	}
 
 	return 0;
Signature · 1 line
2.47.3
#8 lore raw

PATCH 5/15 net: stmmac: qcom-ethqos: move RGMII_CONFIG_DDR_MODE

In reply to Russell King (Oracle)

RGMII_CONFIG_DDR_MODE is always set irrespective of the speed. Move this out of the switch.

Signed-off-by Russell King (Oracle) <[email protected]>
---
 drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c | 8 ++------
 1 file changed, 2 insertions(+), 6 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c +2 -6
index 7e389db40e8b..3540471ff272 100644
@@ -402,10 +402,10 @@ static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos, int speed)
 		return -EINVAL;
 	}
 
+	rgmii_setmask(ethqos, RGMII_CONFIG_DDR_MODE, RGMII_IO_MACRO_CONFIG);
+
 	switch (speed) {
 	case SPEED_1000:
-		rgmii_setmask(ethqos, RGMII_CONFIG_DDR_MODE,
-			      RGMII_IO_MACRO_CONFIG);
 		rgmii_clrmask(ethqos, RGMII_CONFIG_BYPASS_TX_ID_EN,
 			      RGMII_IO_MACRO_CONFIG);
 		rgmii_setmask(ethqos, RGMII_CONFIG_POS_NEG_DATA_SEL,

@@ -443,8 +443,6 @@ static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos, int speed)
 		break;
 
 	case SPEED_100:
-		rgmii_setmask(ethqos, RGMII_CONFIG_DDR_MODE,
-			      RGMII_IO_MACRO_CONFIG);
 		rgmii_setmask(ethqos, RGMII_CONFIG_BYPASS_TX_ID_EN,
 			      RGMII_IO_MACRO_CONFIG);
 		rgmii_clrmask(ethqos, RGMII_CONFIG_POS_NEG_DATA_SEL,

@@ -481,8 +479,6 @@ static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos, int speed)
 		break;
 
 	case SPEED_10:
-		rgmii_setmask(ethqos, RGMII_CONFIG_DDR_MODE,
-			      RGMII_IO_MACRO_CONFIG);
 		rgmii_setmask(ethqos, RGMII_CONFIG_BYPASS_TX_ID_EN,
 			      RGMII_IO_MACRO_CONFIG);
 		rgmii_clrmask(ethqos, RGMII_CONFIG_POS_NEG_DATA_SEL,
Signature · 1 line
2.47.3
#9 lore raw

PATCH 6/15 net: stmmac: qcom-ethqos: move 1G vs 100M/10M RGMII settings

In reply to Russell King (Oracle)

Move RGMII_CONFIG_BYPASS_TX_ID_EN, RGMII_CONFIG_POS_NEG_DATA_SEL and RGMII_CONFIG_PROG_SWAP. There are two states for these: one group for 1G, and the logical inversion for 100M and 10M. Move this out of the switch into an if-else clause.

Signed-off-by Russell King (Oracle) <[email protected]>
---
 .../stmicro/stmmac/dwmac-qcom-ethqos.c        | 26 +++++++++----------
 1 file changed, 12 insertions(+), 14 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c +12 -14
index 3540471ff272..87af44dcef5a 100644
@@ -404,14 +404,24 @@ static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos, int speed)
 
 	rgmii_setmask(ethqos, RGMII_CONFIG_DDR_MODE, RGMII_IO_MACRO_CONFIG);
 
-	switch (speed) {
-	case SPEED_1000:
+	if (speed == SPEED_1000) {
 		rgmii_clrmask(ethqos, RGMII_CONFIG_BYPASS_TX_ID_EN,
 			      RGMII_IO_MACRO_CONFIG);
 		rgmii_setmask(ethqos, RGMII_CONFIG_POS_NEG_DATA_SEL,
 			      RGMII_IO_MACRO_CONFIG);
 		rgmii_setmask(ethqos, RGMII_CONFIG_PROG_SWAP,
 			      RGMII_IO_MACRO_CONFIG);
+	} else {
+		rgmii_setmask(ethqos, RGMII_CONFIG_BYPASS_TX_ID_EN,
+			      RGMII_IO_MACRO_CONFIG);
+		rgmii_clrmask(ethqos, RGMII_CONFIG_POS_NEG_DATA_SEL,
+			      RGMII_IO_MACRO_CONFIG);
+		rgmii_clrmask(ethqos, RGMII_CONFIG_PROG_SWAP,
+			      RGMII_IO_MACRO_CONFIG);
+	}
+
+	switch (speed) {
+	case SPEED_1000:
 		rgmii_clrmask(ethqos, RGMII_CONFIG2_DATA_DIVIDE_CLK_SEL,
 			      RGMII_IO_MACRO_CONFIG2);
 

@@ -443,12 +453,6 @@ static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos, int speed)
 		break;
 
 	case SPEED_100:
-		rgmii_setmask(ethqos, RGMII_CONFIG_BYPASS_TX_ID_EN,
-			      RGMII_IO_MACRO_CONFIG);
-		rgmii_clrmask(ethqos, RGMII_CONFIG_POS_NEG_DATA_SEL,
-			      RGMII_IO_MACRO_CONFIG);
-		rgmii_clrmask(ethqos, RGMII_CONFIG_PROG_SWAP,
-			      RGMII_IO_MACRO_CONFIG);
 		rgmii_clrmask(ethqos, RGMII_CONFIG2_DATA_DIVIDE_CLK_SEL,
 			      RGMII_IO_MACRO_CONFIG2);
 		rgmii_updatel(ethqos, RGMII_CONFIG2_TX_CLK_PHASE_SHIFT_EN,

@@ -479,12 +483,6 @@ static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos, int speed)
 		break;
 
 	case SPEED_10:
-		rgmii_setmask(ethqos, RGMII_CONFIG_BYPASS_TX_ID_EN,
-			      RGMII_IO_MACRO_CONFIG);
-		rgmii_clrmask(ethqos, RGMII_CONFIG_POS_NEG_DATA_SEL,
-			      RGMII_IO_MACRO_CONFIG);
-		rgmii_clrmask(ethqos, RGMII_CONFIG_PROG_SWAP,
-			      RGMII_IO_MACRO_CONFIG);
 		rgmii_clrmask(ethqos, RGMII_CONFIG2_DATA_DIVIDE_CLK_SEL,
 			      RGMII_IO_MACRO_CONFIG2);
 		rgmii_updatel(ethqos, RGMII_CONFIG2_TX_CLK_PHASE_SHIFT_EN,
Signature · 1 line
2.47.3
#10 lore raw

PATCH 7/15 net: stmmac: qcom-ethqos: move two more RGMII_IO_MACRO_CONFIG2 out

In reply to Russell King (Oracle)

RGMII_CONFIG2_DATA_DIVIDE_CLK_SEL is always cleared, and RGMII_CONFIG2_TX_CLK_PHASE_SHIFT_EN is always updated with the phase shift in each path through the switch, so these are independent of the speed. Move them out.

Signed-off-by Russell King (Oracle) <[email protected]>
---
 .../stmicro/stmmac/dwmac-qcom-ethqos.c         | 18 +++++-------------
 1 file changed, 5 insertions(+), 13 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c +5 -13
index 87af44dcef5a..84db57b3d7cb 100644
@@ -420,13 +420,13 @@ static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos, int speed)
 			      RGMII_IO_MACRO_CONFIG);
 	}
 
+	rgmii_clrmask(ethqos, RGMII_CONFIG2_DATA_DIVIDE_CLK_SEL,
+		      RGMII_IO_MACRO_CONFIG2);
+	rgmii_updatel(ethqos, RGMII_CONFIG2_TX_CLK_PHASE_SHIFT_EN, phase_shift,
+		      RGMII_IO_MACRO_CONFIG2);
+
 	switch (speed) {
 	case SPEED_1000:
-		rgmii_clrmask(ethqos, RGMII_CONFIG2_DATA_DIVIDE_CLK_SEL,
-			      RGMII_IO_MACRO_CONFIG2);
-
-		rgmii_updatel(ethqos, RGMII_CONFIG2_TX_CLK_PHASE_SHIFT_EN,
-			      phase_shift, RGMII_IO_MACRO_CONFIG2);
 		rgmii_clrmask(ethqos, RGMII_CONFIG2_RSVD_CONFIG15,
 			      RGMII_IO_MACRO_CONFIG2);
 		rgmii_setmask(ethqos, RGMII_CONFIG2_RX_PROG_SWAP,

@@ -453,10 +453,6 @@ static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos, int speed)
 		break;
 
 	case SPEED_100:
-		rgmii_clrmask(ethqos, RGMII_CONFIG2_DATA_DIVIDE_CLK_SEL,
-			      RGMII_IO_MACRO_CONFIG2);
-		rgmii_updatel(ethqos, RGMII_CONFIG2_TX_CLK_PHASE_SHIFT_EN,
-			      phase_shift, RGMII_IO_MACRO_CONFIG2);
 		rgmii_updatel(ethqos, RGMII_CONFIG_MAX_SPD_PRG_2,
 			      FIELD_PREP(RGMII_CONFIG_MAX_SPD_PRG_2, 1),
 			      RGMII_IO_MACRO_CONFIG);

@@ -483,10 +479,6 @@ static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos, int speed)
 		break;
 
 	case SPEED_10:
-		rgmii_clrmask(ethqos, RGMII_CONFIG2_DATA_DIVIDE_CLK_SEL,
-			      RGMII_IO_MACRO_CONFIG2);
-		rgmii_updatel(ethqos, RGMII_CONFIG2_TX_CLK_PHASE_SHIFT_EN,
-			      phase_shift, RGMII_IO_MACRO_CONFIG2);
 		rgmii_updatel(ethqos, RGMII_CONFIG_MAX_SPD_PRG_9,
 			      FIELD_PREP(RGMII_CONFIG_MAX_SPD_PRG_9, 19),
 			      RGMII_IO_MACRO_CONFIG);
Signature · 1 line
2.47.3
#11 lore raw

PATCH 8/15 net: stmmac: qcom-ethqos: move 100M/10M speed programming

In reply to Russell King (Oracle)

Move the speed programming for 100M and 10M out of the switch. There is no programming done for 1G speed.

It looks like there are two fields, 7:6 which are programemd to '1' to select a /2 divisor for 100M, and bits 16:8 which are programmed to '19' to select a /20 divisor.

Signed-off-by Russell King (Oracle) <[email protected]>
---
 .../ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c   | 15 +++++++++------
 1 file changed, 9 insertions(+), 6 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c +9 -6
index 84db57b3d7cb..10676897619e 100644
@@ -425,6 +425,15 @@ static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos, int speed)
 	rgmii_updatel(ethqos, RGMII_CONFIG2_TX_CLK_PHASE_SHIFT_EN, phase_shift,
 		      RGMII_IO_MACRO_CONFIG2);
 
+	if (speed == SPEED_100)
+		rgmii_updatel(ethqos, RGMII_CONFIG_MAX_SPD_PRG_2,
+			      FIELD_PREP(RGMII_CONFIG_MAX_SPD_PRG_2, 1),
+			      RGMII_IO_MACRO_CONFIG);
+	else if (speed == SPEED_10)
+		rgmii_updatel(ethqos, RGMII_CONFIG_MAX_SPD_PRG_9,
+			      FIELD_PREP(RGMII_CONFIG_MAX_SPD_PRG_9, 19),
+			      RGMII_IO_MACRO_CONFIG);
+
 	switch (speed) {
 	case SPEED_1000:
 		rgmii_clrmask(ethqos, RGMII_CONFIG2_RSVD_CONFIG15,

@@ -453,9 +462,6 @@ static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos, int speed)
 		break;
 
 	case SPEED_100:
-		rgmii_updatel(ethqos, RGMII_CONFIG_MAX_SPD_PRG_2,
-			      FIELD_PREP(RGMII_CONFIG_MAX_SPD_PRG_2, 1),
-			      RGMII_IO_MACRO_CONFIG);
 		rgmii_clrmask(ethqos, RGMII_CONFIG2_RSVD_CONFIG15,
 			      RGMII_IO_MACRO_CONFIG2);
 

@@ -479,9 +485,6 @@ static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos, int speed)
 		break;
 
 	case SPEED_10:
-		rgmii_updatel(ethqos, RGMII_CONFIG_MAX_SPD_PRG_9,
-			      FIELD_PREP(RGMII_CONFIG_MAX_SPD_PRG_9, 19),
-			      RGMII_IO_MACRO_CONFIG);
 		rgmii_clrmask(ethqos, RGMII_CONFIG2_RSVD_CONFIG15,
 			      RGMII_IO_MACRO_CONFIG2);
 		if (ethqos->has_emac_ge_3)
Signature · 1 line
2.47.3
#12 lore raw

PATCH 9/15 net: stmmac: qcom-ethqos: move RGMII_CONFIG2_RSVD_CONFIG15 out

In reply to Russell King (Oracle)

All paths through the switch clear the RGMII_CONFIG2_RSVD_CONFIG15 field. move it out of the switch statement.

Signed-off-by Russell King (Oracle) <[email protected]>
---
 .../net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c    | 10 +++-------
 1 file changed, 3 insertions(+), 7 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c +3 -7
index 10676897619e..73f0ebc5eddd 100644
@@ -434,10 +434,11 @@ static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos, int speed)
 			      FIELD_PREP(RGMII_CONFIG_MAX_SPD_PRG_9, 19),
 			      RGMII_IO_MACRO_CONFIG);
 
+	rgmii_clrmask(ethqos, RGMII_CONFIG2_RSVD_CONFIG15,
+		      RGMII_IO_MACRO_CONFIG2);
+
 	switch (speed) {
 	case SPEED_1000:
-		rgmii_clrmask(ethqos, RGMII_CONFIG2_RSVD_CONFIG15,
-			      RGMII_IO_MACRO_CONFIG2);
 		rgmii_setmask(ethqos, RGMII_CONFIG2_RX_PROG_SWAP,
 			      RGMII_IO_MACRO_CONFIG2);
 

@@ -462,9 +463,6 @@ static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos, int speed)
 		break;
 
 	case SPEED_100:
-		rgmii_clrmask(ethqos, RGMII_CONFIG2_RSVD_CONFIG15,
-			      RGMII_IO_MACRO_CONFIG2);
-
 		if (ethqos->has_emac_ge_3)
 			rgmii_setmask(ethqos, RGMII_CONFIG2_RX_PROG_SWAP,
 				      RGMII_IO_MACRO_CONFIG2);

@@ -485,8 +483,6 @@ static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos, int speed)
 		break;
 
 	case SPEED_10:
-		rgmii_clrmask(ethqos, RGMII_CONFIG2_RSVD_CONFIG15,
-			      RGMII_IO_MACRO_CONFIG2);
 		if (ethqos->has_emac_ge_3)
 			rgmii_setmask(ethqos, RGMII_CONFIG2_RX_PROG_SWAP,
 				      RGMII_IO_MACRO_CONFIG2);
Signature · 1 line
2.47.3
#13 lore raw

PATCH 10/15 net: stmmac: qcom-ethqos: move RGMII_CONFIG2_RX_PROG_SWAP

In reply to Russell King (Oracle)

Move RGMII_CONFIG2_RX_PROG_SWAP out of the switch. 1G speed always sets this field. 100M and 10M sets it for has_emac_ge_3 devices, otherwise it is cleared.

Signed-off-by Russell King (Oracle) <[email protected]>
---
 .../stmicro/stmmac/dwmac-qcom-ethqos.c        | 21 ++++++-------------
 1 file changed, 6 insertions(+), 15 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c +6 -15
index 73f0ebc5eddd..a24f0b24f778 100644
@@ -437,11 +437,15 @@ static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos, int speed)
 	rgmii_clrmask(ethqos, RGMII_CONFIG2_RSVD_CONFIG15,
 		      RGMII_IO_MACRO_CONFIG2);
 
-	switch (speed) {
-	case SPEED_1000:
+	if (speed == SPEED_1000 || ethqos->has_emac_ge_3)
 		rgmii_setmask(ethqos, RGMII_CONFIG2_RX_PROG_SWAP,
 			      RGMII_IO_MACRO_CONFIG2);
+	else
+		rgmii_clrmask(ethqos, RGMII_CONFIG2_RX_PROG_SWAP,
+			      RGMII_IO_MACRO_CONFIG2);
 
+	switch (speed) {
+	case SPEED_1000:
 		/* PRG_RCLK_DLY = TCXO period * TCXO_CYCLES_CNT / 2 * RX delay ns,
 		 * in practice this becomes PRG_RCLK_DLY = 52 * 4 / 2 * RX delay ns
 		 */

@@ -463,13 +467,6 @@ static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos, int speed)
 		break;
 
 	case SPEED_100:
-		if (ethqos->has_emac_ge_3)
-			rgmii_setmask(ethqos, RGMII_CONFIG2_RX_PROG_SWAP,
-				      RGMII_IO_MACRO_CONFIG2);
-		else
-			rgmii_clrmask(ethqos, RGMII_CONFIG2_RX_PROG_SWAP,
-				      RGMII_IO_MACRO_CONFIG2);
-
 		/* Write 0x5 to PRG_RCLK_DLY_CODE */
 		rgmii_updatel(ethqos, SDCC_DDR_CONFIG_EXT_PRG_RCLK_DLY_CODE,
 			      FIELD_PREP(SDCC_DDR_CONFIG_EXT_PRG_RCLK_DLY_CODE,

@@ -483,12 +480,6 @@ static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos, int speed)
 		break;
 
 	case SPEED_10:
-		if (ethqos->has_emac_ge_3)
-			rgmii_setmask(ethqos, RGMII_CONFIG2_RX_PROG_SWAP,
-				      RGMII_IO_MACRO_CONFIG2);
-		else
-			rgmii_clrmask(ethqos, RGMII_CONFIG2_RX_PROG_SWAP,
-				      RGMII_IO_MACRO_CONFIG2);
 		/* Write 0x5 to PRG_RCLK_DLY_CODE */
 		rgmii_updatel(ethqos, SDCC_DDR_CONFIG_EXT_PRG_RCLK_DLY_CODE,
 			      FIELD_PREP(SDCC_DDR_CONFIG_EXT_PRG_RCLK_DLY_CODE,
Signature · 1 line
2.47.3
#14 lore raw

PATCH 11/15 net: stmmac: qcom-ethqos: finally eliminate the switch

In reply to Russell King (Oracle)

Move the RCLK delay configuration out of the switch, which just leaves the RGMII_CONFIG_LOOPBACK_EN setting in all three paths. This makes it trivial to eliminate the switch.

Signed-off-by Russell King (Oracle) <[email protected]>
---
 .../stmicro/stmmac/dwmac-qcom-ethqos.c        | 47 +++++++------------
 1 file changed, 16 insertions(+), 31 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c +16 -31
index a24f0b24f778..c88c693137d6 100644
@@ -444,8 +444,18 @@ static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos, int speed)
 		rgmii_clrmask(ethqos, RGMII_CONFIG2_RX_PROG_SWAP,
 			      RGMII_IO_MACRO_CONFIG2);
 
-	switch (speed) {
-	case SPEED_1000:
+	if (speed != SPEED_1000) {
+		/* Write 0x5 to PRG_RCLK_DLY_CODE */
+		rgmii_updatel(ethqos, SDCC_DDR_CONFIG_EXT_PRG_RCLK_DLY_CODE,
+			      FIELD_PREP(SDCC_DDR_CONFIG_EXT_PRG_RCLK_DLY_CODE,
+					 5), SDCC_HC_REG_DDR_CONFIG);
+
+		rgmii_setmask(ethqos, SDCC_DDR_CONFIG_EXT_PRG_RCLK_DLY,
+			      SDCC_HC_REG_DDR_CONFIG);
+
+		rgmii_setmask(ethqos, SDCC_DDR_CONFIG_EXT_PRG_RCLK_DLY_EN,
+			      SDCC_HC_REG_DDR_CONFIG);
+	} else {
 		/* PRG_RCLK_DLY = TCXO period * TCXO_CYCLES_CNT / 2 * RX delay ns,
 		 * in practice this becomes PRG_RCLK_DLY = 52 * 4 / 2 * RX delay ns
 		 */

@@ -460,39 +470,14 @@ static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos, int speed)
 				      FIELD_PREP(SDCC_DDR_CONFIG_PRG_RCLK_DLY,
 						 57), SDCC_HC_REG_DDR_CONFIG);
 		}
-		rgmii_setmask(ethqos, SDCC_DDR_CONFIG_PRG_DLY_EN,
-			      SDCC_HC_REG_DDR_CONFIG);
-		rgmii_updatel(ethqos, RGMII_CONFIG_LOOPBACK_EN,
-			      loopback, RGMII_IO_MACRO_CONFIG);
-		break;
-
-	case SPEED_100:
-		/* Write 0x5 to PRG_RCLK_DLY_CODE */
-		rgmii_updatel(ethqos, SDCC_DDR_CONFIG_EXT_PRG_RCLK_DLY_CODE,
-			      FIELD_PREP(SDCC_DDR_CONFIG_EXT_PRG_RCLK_DLY_CODE,
-					 5), SDCC_HC_REG_DDR_CONFIG);
-		rgmii_setmask(ethqos, SDCC_DDR_CONFIG_EXT_PRG_RCLK_DLY,
-			      SDCC_HC_REG_DDR_CONFIG);
-		rgmii_setmask(ethqos, SDCC_DDR_CONFIG_EXT_PRG_RCLK_DLY_EN,
-			      SDCC_HC_REG_DDR_CONFIG);
-		rgmii_updatel(ethqos, RGMII_CONFIG_LOOPBACK_EN,
-			      loopback, RGMII_IO_MACRO_CONFIG);
-		break;
 
-	case SPEED_10:
-		/* Write 0x5 to PRG_RCLK_DLY_CODE */
-		rgmii_updatel(ethqos, SDCC_DDR_CONFIG_EXT_PRG_RCLK_DLY_CODE,
-			      FIELD_PREP(SDCC_DDR_CONFIG_EXT_PRG_RCLK_DLY_CODE,
-					 5), SDCC_HC_REG_DDR_CONFIG);
-		rgmii_setmask(ethqos, SDCC_DDR_CONFIG_EXT_PRG_RCLK_DLY,
-			      SDCC_HC_REG_DDR_CONFIG);
-		rgmii_setmask(ethqos, SDCC_DDR_CONFIG_EXT_PRG_RCLK_DLY_EN,
+		rgmii_setmask(ethqos, SDCC_DDR_CONFIG_PRG_DLY_EN,
 			      SDCC_HC_REG_DDR_CONFIG);
-		rgmii_updatel(ethqos, RGMII_CONFIG_LOOPBACK_EN,
-			      loopback, RGMII_IO_MACRO_CONFIG);
-		break;
 	}
 
+	rgmii_updatel(ethqos, RGMII_CONFIG_LOOPBACK_EN, loopback,
+		      RGMII_IO_MACRO_CONFIG);
+
 	return 0;
 }
Signature · 1 line
2.47.3
#15 lore raw

PATCH 12/15 net: stmmac: qcom-ethqos: simplify prg_rclk_dly programming

In reply to Russell King (Oracle)

Rather than coding the entire register update twice with different values, use a local variable to specify the value and have one register update statement that uses this local variable. This results in neater code.

Signed-off-by Russell King (Oracle) <[email protected]>
---
 .../net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c | 13 +++++++------
 1 file changed, 7 insertions(+), 6 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c +7 -6
index c88c693137d6..f9d6e97f197a 100644
@@ -374,6 +374,7 @@ static int ethqos_dll_configure(struct qcom_ethqos *ethqos)
 static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos, int speed)
 {
 	struct device *dev = &ethqos->pdev->dev;
+	unsigned int prg_rclk_dly;
 	int phase_shift;
 	int loopback;
 

@@ -461,16 +462,16 @@ static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos, int speed)
 		 */
 		if (ethqos->has_emac_ge_3) {
 			/* 0.9 ns */
-			rgmii_updatel(ethqos, SDCC_DDR_CONFIG_PRG_RCLK_DLY,
-				      FIELD_PREP(SDCC_DDR_CONFIG_PRG_RCLK_DLY,
-						 115), SDCC_HC_REG_DDR_CONFIG);
+			prg_rclk_dly = 115;
 		} else {
 			/* 1.8 ns */
-			rgmii_updatel(ethqos, SDCC_DDR_CONFIG_PRG_RCLK_DLY,
-				      FIELD_PREP(SDCC_DDR_CONFIG_PRG_RCLK_DLY,
-						 57), SDCC_HC_REG_DDR_CONFIG);
+			prg_rclk_dly = 57;
 		}
 
+		rgmii_updatel(ethqos, SDCC_DDR_CONFIG_PRG_RCLK_DLY,
+			      FIELD_PREP(SDCC_DDR_CONFIG_PRG_RCLK_DLY,
+					 prg_rclk_dly), SDCC_HC_REG_DDR_CONFIG);
+
 		rgmii_setmask(ethqos, SDCC_DDR_CONFIG_PRG_DLY_EN,
 			      SDCC_HC_REG_DDR_CONFIG);
 	}
Signature · 1 line
2.47.3
#16 lore raw

PATCH 13/15 net: stmmac: qcom-ethqos: move loopback decision next to reg update

In reply to Russell King (Oracle)

Move the loopback decision next to the register update, and make the local variable unsigned. As a result, there is now no need for the comment referring to the programming being later.

Signed-off-by Russell King (Oracle) <[email protected]>
---
 .../ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c    | 14 ++++++--------
 1 file changed, 6 insertions(+), 8 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c +6 -8
index f9d6e97f197a..3faea7ceebd3 100644
@@ -374,9 +374,8 @@ static int ethqos_dll_configure(struct qcom_ethqos *ethqos)
 static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos, int speed)
 {
 	struct device *dev = &ethqos->pdev->dev;
-	unsigned int prg_rclk_dly;
+	unsigned int prg_rclk_dly, loopback;
 	int phase_shift;
-	int loopback;
 
 	/* Determine if the PHY adds a 2 ns TX delay or the MAC handles it */
 	if (ethqos->phy_mode == PHY_INTERFACE_MODE_RGMII_ID ||

@@ -389,12 +388,6 @@ static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos, int speed)
 	rgmii_clrmask(ethqos, RGMII_CONFIG2_TX_TO_RX_LOOPBACK_EN,
 		      RGMII_IO_MACRO_CONFIG2);
 
-	/* Determine if this platform wants loopback enabled after programming */
-	if (ethqos->rgmii_config_loopback_en)
-		loopback = RGMII_CONFIG_LOOPBACK_EN;
-	else
-		loopback = 0;
-
 	/* Select RGMII, write 0 to interface select */
 	rgmii_clrmask(ethqos, RGMII_CONFIG_INTF_SEL, RGMII_IO_MACRO_CONFIG);
 

@@ -476,6 +469,11 @@ static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos, int speed)
 			      SDCC_HC_REG_DDR_CONFIG);
 	}
 
+	if (ethqos->rgmii_config_loopback_en)
+		loopback = RGMII_CONFIG_LOOPBACK_EN;
+	else
+		loopback = 0;
+
 	rgmii_updatel(ethqos, RGMII_CONFIG_LOOPBACK_EN, loopback,
 		      RGMII_IO_MACRO_CONFIG);
Signature · 1 line
2.47.3
#17 lore raw

PATCH 14/15 net: stmmac: qcom-ethqos: correct prg_rclk_dly comment

In reply to Russell King (Oracle)

The comment for calculating the prg_rclk_dly value is incorrect as it omits the brackets around the divisor. Add the brackets to allow the reader to correctly evaluate the value. Validated with the values given in the driver.

Signed-off-by Russell King (Oracle) <[email protected]>
---
 drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c +4 -2
index 3faea7ceebd3..0cc5b925cdb6 100644
@@ -450,8 +450,10 @@ static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos, int speed)
 		rgmii_setmask(ethqos, SDCC_DDR_CONFIG_EXT_PRG_RCLK_DLY_EN,
 			      SDCC_HC_REG_DDR_CONFIG);
 	} else {
-		/* PRG_RCLK_DLY = TCXO period * TCXO_CYCLES_CNT / 2 * RX delay ns,
-		 * in practice this becomes PRG_RCLK_DLY = 52 * 4 / 2 * RX delay ns
+		/* PRG_RCLK_DLY = TCXO period * TCXO_CYCLES_CNT /
+		 *  (2 * RX delay ns),
+		 * in practice this becomes PRG_RCLK_DLY = 52 * 4 /
+		 *  (2 * RX delay ns)
 		 */
 		if (ethqos->has_emac_ge_3) {
 			/* 0.9 ns */
Signature · 1 line
2.47.3
#18 lore raw

PATCH 15/15 net: stmmac: qcom-ethqos: move phase_shift to register update site

In reply to Russell King (Oracle)

Move the determination of the phase shift enable alongside the register update, and make "phase_shift" unsigned.

Signed-off-by Russell King (Oracle) <[email protected]>
---
 .../ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c | 17 +++++++++--------
 1 file changed, 9 insertions(+), 8 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c +9 -8
index 0cc5b925cdb6..18412a6ca77a 100644
@@ -375,14 +375,7 @@ static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos, int speed)
 {
 	struct device *dev = &ethqos->pdev->dev;
 	unsigned int prg_rclk_dly, loopback;
-	int phase_shift;
-
-	/* Determine if the PHY adds a 2 ns TX delay or the MAC handles it */
-	if (ethqos->phy_mode == PHY_INTERFACE_MODE_RGMII_ID ||
-	    ethqos->phy_mode == PHY_INTERFACE_MODE_RGMII_TXID)
-		phase_shift = 0;
-	else
-		phase_shift = RGMII_CONFIG2_TX_CLK_PHASE_SHIFT_EN;
+	unsigned int phase_shift;
 
 	/* Disable loopback mode */
 	rgmii_clrmask(ethqos, RGMII_CONFIG2_TX_TO_RX_LOOPBACK_EN,

@@ -416,6 +409,14 @@ static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos, int speed)
 
 	rgmii_clrmask(ethqos, RGMII_CONFIG2_DATA_DIVIDE_CLK_SEL,
 		      RGMII_IO_MACRO_CONFIG2);
+
+	/* Determine if the PHY adds a 2 ns TX delay or the MAC handles it */
+	if (ethqos->phy_mode == PHY_INTERFACE_MODE_RGMII_ID ||
+	    ethqos->phy_mode == PHY_INTERFACE_MODE_RGMII_TXID)
+		phase_shift = 0;
+	else
+		phase_shift = RGMII_CONFIG2_TX_CLK_PHASE_SHIFT_EN;
+
 	rgmii_updatel(ethqos, RGMII_CONFIG2_TX_CLK_PHASE_SHIFT_EN, phase_shift,
 		      RGMII_IO_MACRO_CONFIG2);
Signature · 1 line
2.47.3