spi: dt-bindings: spi-rockchip: restrict num-cs
Subsystems (3)
PATCH 1/1 spi: dt-bindings: spi-rockchip: restrict num-cs
In the driver spi-rockchip.c max_native_cs is limited to 4 and the default num-cs property is 1. Restrict num-cs in spi-rockchip.yaml.
--- Documentation/devicetree/bindings/spi/spi-rockchip.yaml | 5 +++++ 1 file changed, 5 insertions(+)
Documentation/devicetree/bindings/spi/spi-rockchip.yaml +5 -0
@@ -65,6 +65,11 @@ properties: - const: tx - const: rx + num-cs: + default: 1 + minimum: 1 + maximum: 4 + rx-sample-delay-ns: default: 0 description:
--
2.39.2
Quoted 5 lines · Johan Jonker
In the driver
spi-rockchip.cmax_native_csis limited to 4 and the default num-cs property is 1. Restrict num-cs inspi-rockchip.yaml.Signed-off-by Johan Jonker <[email protected]>---
Best regards,
Krzysztof
Quoted 3 lines · Johan Jonker
In the driver
spi-rockchip.cmax_native_csis limited to 4 and the default num-cs property is 1. Restrict num-cs inspi-rockchip.yaml.
Doesn't num-cs include gpio chip selects too?
I have a setup with num-cs = <12> which uses non-native cs-gpios just fine
Luis
Quoted 29 lines
Signed-off-by Johan Jonker <[email protected]>--- Documentation/devicetree/bindings/spi/spi-rockchip.yaml | 5 +++++ 1 file changed, 5 insertions(+)Documentation/devicetree/bindings/spi/spi-rockchip.yaml +5
-1@@ -65,6 +65,11 @@ properties: - const: tx - const: rx + num-cs: + default: 1 + minimum: 1 + maximum: 4 + rx-sample-delay-ns: default: 0 description: --2.39.2
_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip
Quoted 8 lines · Luis de Arquer
Quoted 3 lines · Johan Jonker
In the driver
spi-rockchip.cmax_native_csis limited to 4 and the default num-cs property is 1. Restrict num-cs inspi-rockchip.yaml.Doesn't num-cs include gpio chip selects too?
I have a setup with num-cs = <12> which uses non-native cs-gpios just fine
Given that bindings and Linux drivers capabilities are 2 separate things.
However this document has also a purpose that must notify mainline maintainers if users submit bogus DT values.
Currently that limit is set to 4 in the mainline driver.
You are free to submit a real board file/patch serie afterwords as proof for review with 12 spi chips and then adjust this limit and increase ROCKCHIP_SPI_MAX_CS_NUM.
Johan
Quoted 33 lines
Luis
Quoted 29 lines
Signed-off-by Johan Jonker <[email protected]>---
Documentation/devicetree/bindings/spi/spi-rockchip.yaml| 5 +++++1 file changed, 5 insertions(+)Documentation/devicetree/bindings/spi/spi-rockchip.yaml +0
-0@@ -65,6 +65,11 @@ properties:- const: tx
- const: rx+ num-cs:
+ default: 1
+ minimum: 1
+ maximum: 4
+
rx-sample-delay-ns:
default: 0
description:Signature · 7 lines
2.39.2 _______________________________________________ Linux-rockchip mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-rockchip
Quoted 9 lines · Johan Jonker
Quoted 5 lines · Luis de Arquer
Quoted 3 lines · Johan Jonker
In the driver
spi-rockchip.cmax_native_csis limited to 4 and the default num-cs property is 1. Restrict num-cs inspi-rockchip.yaml.
Quoted 7 lines
Quoted 2 lines
Doesn't num-cs include gpio chip selects too?
I have a setup with num-cs = <12> which uses non-native cs-gpios just fineGiven that bindings and Linux drivers capabilities are 2 separate things.
However this document has also a purpose that must notify mainline maintainers if users submit bogus DT values.
Currently that limit is set to 4 in the mainline driver.
You are free to submit a real board file/patch serie afterwords as proof for review with 12 spi chips and then adjust this limit and increaseROCKCHIP_SPI_MAX_CS_NUM.
Hi Johan,
OK to that, I was not aware a driver could limit num-cs (I thought it could be extended with as many gpios as needed without involving the controller driver). I thought of num-cs as a spi subsystem generic thing.
In fact, I was reviewing the setup I mentioned, and even it defines 12 cs in the controller with no driver complaints, so far only 3 of them are mapped to devices (I'll have to review the driver before going any futher!)
Luis
Quoted 36 lines
Johan
Quoted 33 lines
Luis
Quoted 29 lines
Signed-off-by Johan Jonker <[email protected]>--- Documentation/devicetree/bindings/spi/spi-rockchip.yaml | 5 +++++ 1 file changed, 5 insertions(+)Documentation/devicetree/bindings/spi/spi-rockchip.yaml +5
-0@@ -65,6 +65,11 @@ properties: - const: tx - const: rx + num-cs: + default: 1 + minimum: 1 + maximum: 4 + rx-sample-delay-ns: default: 0 description:Signature · 7 lines
2.39.2 _______________________________________________ Linux-rockchip mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-rockchip
Quoted 9 lines · Johan Jonker
Quoted 5 lines · Luis de Arquer
Quoted 3 lines · Johan Jonker
In the driver
spi-rockchip.cmax_native_csis limited to 4 and the default num-cs property is 1. Restrict num-cs inspi-rockchip.yaml.
Quoted 4 lines
Quoted 2 lines
Doesn't num-cs include gpio chip selects too?
I have a setup with num-cs = <12> which uses non-native cs-gpios just fineGiven that bindings and Linux drivers capabilities are 2 separate things.
Er, that's the whole point - bindings and drivers *are* separate things, and bindings do not describe drivers. Not least since the fundamental model is to have one canonical binding for multiple different drivers to consume.
There seems to be some ambiguity as to whether the common "num-cs" property is supposed to describe the number of dedicated hardware chipselects or the total number including additional GPIOs, but either way this change appears to be objectively wrong - if it's the former than the comment in the driver plus a survey of a few TRMs implies that the maximum number of hardware lines is 2; if it's the latter then obviously it's valid for a platform to wire up 3 or more additional GPIOs as desired, and for a DT to accurately describe that, regardless of whether any particular consumer happens to support it yet or not. For example, AFAICS the U-Boot and FreeBSD drivers for Rockchip SPI appear not to support GPIO chipselects at all.
Thanks,
Robin.
Quoted 44 lines
However this document has also a purpose that must notify mainline maintainers if users submit bogus DT values.
Currently that limit is set to 4 in the mainline driver.
You are free to submit a real board file/patch serie afterwords as proof for review with 12 spi chips and then adjust this limit and increaseROCKCHIP_SPI_MAX_CS_NUM.Johan
Quoted 28 lines
Luis
Quoted 25 lines
Signed-off-by Johan Jonker <[email protected]>--- Documentation/devicetree/bindings/spi/spi-rockchip.yaml | 5 +++++ 1 file changed, 5 insertions(+)Documentation/devicetree/bindings/spi/spi-rockchip.yaml +5
-0@@ -65,6 +65,11 @@ properties: - const: tx - const: rx + num-cs: + default: 1 + minimum: 1 + maximum: 4 + rx-sample-delay-ns: default: 0 description:Signature · 1 line
2.39.2Quoted 5 lines
Quoted 4 lines
_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip
Hi Robin,
Quoted 10 lines · Robin Murphy
Quoted 9 lines · Johan Jonker
Quoted 5 lines · Luis de Arquer
Quoted 3 lines · Johan Jonker
In the driver
spi-rockchip.cmax_native_csis limited to 4 and the default num-cs property is 1. Restrict num-cs inspi-rockchip.yaml.
Quoted 9 lines
Quoted 4 lines
Quoted 2 lines
Doesn't num-cs include gpio chip selects too?
I have a setup with num-cs = <12> which uses non-native cs-gpios just fineGiven that bindings and Linux drivers capabilities are 2 separate things.
Er, that's the whole point - bindings and drivers *are* separate things, and bindings do not describe drivers. Not least since the fundamental model is to have one canonical binding for multiple different drivers to consume.
There seems to be some ambiguity as to whether the common "num-cs" property is supposed to describe the number of dedicated hardware chipselects or the total number including additional GPIOs, but either way this change appears to be objectively wrong - if it's the former than the comment in the driver plus a survey of a few TRMs implies that the maximum number of hardware lines is 2; if it's the latter then obviously it's valid for a platform to wire up 3 or more additional GPIOs as desired, and for a DT to accurately describe that, regardless of whether any particular consumer happens to support it yet or not. For example, AFAICS the U-Boot and FreeBSD drivers for Rockchip SPI appear not to support GPIO chipselects at all.
I always understood num-cs was a spi subsystem thing, which can be extended with as many gpios as needed.
However, it looks spi-rockchip may be limiting num-cs to 4 after all.
It keeps a copy of the state of the chip selects into an array 'cs_asserted' of size 4. It wouldn't be a problem if it wasn't because the driver sets the flag SPI_CONTROLLER_GPIO_SS, which makes driver's set_cs() function to be called even for gpio lines.
All this leads to an out of bounds access when num-cs > 4.
I was able to reproduce the issue with 6 spidev devices (all with gpio cs) adding 2 guard u8 variables in 'struct rockchip_spi' right after 'cs_asserted' array, and they got overwritten when accessing devices spidev0.4 and spidev0.5
Even though I did the test with a downstream kernel (I need more time to test on mainline), the driver is mostly identical, and the problem seems to persist in mainline.
I reviewed and prepared a fix on my system. I am building the fix on linux-rockchip tree, and I will try to post it for review soon.
Luis
Quoted 47 lines
Thanks,
Robin.Quoted 44 lines
However this document has also a purpose that must notify mainline maintainers if users submit bogus DT values.
Currently that limit is set to 4 in the mainline driver.
You are free to submit a real board file/patch serie afterwords as proof for review with 12 spi chips and then adjust this limit and increaseROCKCHIP_SPI_MAX_CS_NUM.Johan
Quoted 28 lines
Luis
Quoted 25 lines
Signed-off-by Johan Jonker <[email protected]>---
Documentation/devicetree/bindings/spi/spi-rockchip.yaml| 5 +++++1 file changed, 5 insertions(+)Documentation/devicetree/bindings/spi/spi-rockchip.yaml +0
-0@@ -65,6 +65,11 @@ properties:- const: tx
- const: rx+ num-cs:
+ default: 1
+ minimum: 1
+ maximum: 4
+
rx-sample-delay-ns:
default: 0
description:Signature · 1 line
2.39.2Quoted 5 lines
Quoted 4 lines
_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip