Skip to contentSkip to conversation

ARM: dts: rockchip: rk3588-rock-5b-u-boot: add USB 2.0 host

PATCH Superseded Eugen Hristev 3 participants 14 messages Apr 19, 2023 – May 9, 2023

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

PATCH v5 1/6 ARM: dts: rockchip: rk3588-rock-5b-u-boot: add USB 2.0 host

Add USB 2.0 host nodes and PHYs.

---
Changes in v5:
- none

Changes in v4:
- removed u-boot,dm-spl on regulator which was useless
- moved usb nodes to rk3588s-u-boot-dtsi

Changes in v2,v3:
- none

 arch/arm/dts/rk3588-rock-5b-u-boot.dtsi | 82 +++++++++++++++++++++++
 arch/arm/dts/rk3588s-u-boot.dtsi        | 86 +++++++++++++++++++++++++
 2 files changed, 168 insertions(+)
arch/arm/dts/rk3588-rock-5b-u-boot.dtsi +82 -0
index bee4c32e8965..93942b105c3d 100644
@@ -4,6 +4,9 @@
  */
 
 #include "rk3588-u-boot.dtsi"
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	aliases {
@@ -13,6 +16,18 @@
 	chosen {
 		u-boot,spl-boot-order = &sdmmc;
 	};
+
+	vcc5v0_host: vcc5v0-host-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_host";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&gpio4 RK_PB0 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_host_en>;
+		vin-supply = <&vcc5v0_sys>;
+	};
 };
 
 &sdmmc {
@@ -20,3 +35,70 @@
 	bootph-pre-ram;
 	status = "okay";
 };
+
+&pinctrl {
+	usb {
+		vcc5v0_host_en: vcc5v0-host-en {
+			rockchip,pins = <4 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&usb_host0_ehci {
+	companion = <&usb_host0_ohci>;
+	phys = <&u2phy2_host>;
+	phy-names = "usb2-phy";
+	status = "okay";
+};
+
+&usb_host0_ohci {
+	phys = <&u2phy2_host>;
+	phy-names = "usb2-phy";
+	status = "okay";
+};
+
+&usb2phy2_grf {
+	status = "okay";
+};
+
+&u2phy2 {
+	resets = <&cru SRST_OTGPHY_U2_0>, <&cru SRST_P_USB2PHY_U2_0_GRF0>;
+	reset-names = "phy", "apb";
+	clock-output-names = "usb480m_phy2";
+	status = "okay";
+};
+
+&u2phy2_host {
+	phy-supply = <&vcc5v0_host>;
+	status = "okay";
+};
+
+&usb_host1_ehci {
+	companion = <&usb_host1_ohci>;
+	phys = <&u2phy3_host>;
+	phy-names = "usb2-phy";
+	status = "okay";
+};
+
+&usb_host1_ohci {
+	phys = <&u2phy3_host>;
+	phy-names = "usb2-phy";
+	status = "okay";
+};
+
+&usb2phy3_grf {
+	status = "okay";
+};
+
+&u2phy3 {
+	resets = <&cru SRST_OTGPHY_U2_1>, <&cru SRST_P_USB2PHY_U2_1_GRF0>;
+	reset-names = "phy", "apb";
+	clock-output-names = "usb480m_phy3";
+	status = "okay";
+};
+
+&u2phy3_host {
+	phy-supply = <&vcc5v0_host>;
+	status = "okay";
+};
+
arch/arm/dts/rk3588s-u-boot.dtsi +86 -0

98 lines not on this page · raw message

Signature · 1 line
2.34.1
#1 lore raw

PATCH v5 2/6 configs: rockchip: rock5b-rk3588: enable USB and regulators

Enable USB command, USB drivers, PHY and regulators, for USB host operations.

---
 configs/rock5b-rk3588_defconfig | 17 +++++++++++++++++
 1 file changed, 17 insertions(+)
configs/rock5b-rk3588_defconfig +17 -0
index f3026c7ea166..8d76c1eb4d42 100644
@@ -41,7 +41,9 @@ CONFIG_SPL_STACK_R=y
 CONFIG_SPL_ATF=y
 CONFIG_CMD_GPT=y
 CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
 # CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_REGULATOR=y
 # CONFIG_SPL_DOS_PARTITION is not set
 CONFIG_SPL_OF_CONTROL=y
 CONFIG_OF_LIVE=y
@@ -61,7 +63,9 @@ CONFIG_MMC_SDHCI_SDMA=y
 CONFIG_MMC_SDHCI_ROCKCHIP=y
 CONFIG_ETH_DESIGNWARE=y
 CONFIG_GMAC_ROCKCHIP=y
+CONFIG_PHY_ROCKCHIP_INNO_USB2=y
 CONFIG_REGULATOR_PWM=y
+CONFIG_DM_REGULATOR_FIXED=y
 CONFIG_PWM_ROCKCHIP=y
 CONFIG_SPL_RAM=y
 CONFIG_BAUDRATE=1500000
@@ -69,4 +73,17 @@ CONFIG_DEBUG_UART_SHIFT=2
 CONFIG_DEBUG_UART_ANNOUNCE=y
 CONFIG_SYSRESET=y
 # CONFIG_BINMAN_FDT is not set
+CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_GENERIC=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_OHCI_GENERIC=y
+CONFIG_USB_HOST_ETHER=y
+CONFIG_USB_ETHER_ASIX=y
+CONFIG_USB_ETHER_ASIX88179=y
+CONFIG_USB_ETHER_LAN75XX=y
+CONFIG_USB_ETHER_LAN78XX=y
+CONFIG_USB_ETHER_MCS7830=y
+CONFIG_USB_ETHER_RTL8152=y
+CONFIG_USB_ETHER_SMSC95XX=y
 CONFIG_ERRNO_STR=y
Signature · 1 line
2.34.1
Reviewed-by on v5 2/6
#2 lore raw

Re: [PATCH v5 2/6] configs: rockchip: rock5b-rk3588: enable USB and regulators

Quoted 4 lines · Eugen Hristev

Enable USB command, USB drivers, PHY and regulators, for USB host operations.

Thanks,
- Kever

Quoted 46 lines
---
  configs/rock5b-rk3588_defconfig | 17 +++++++++++++++++
  1 file changed, 17 insertions(+)
configs/rock5b-rk3588_defconfig +17 -0
index f3026c7ea166..8d76c1eb4d42 100644
@@ -41,7 +41,9 @@ CONFIG_SPL_STACK_R=y
  CONFIG_SPL_ATF=y
  CONFIG_CMD_GPT=y
  CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
  # CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_REGULATOR=y
  # CONFIG_SPL_DOS_PARTITION is not set
  CONFIG_SPL_OF_CONTROL=y
  CONFIG_OF_LIVE=y
@@ -61,7 +63,9 @@ CONFIG_MMC_SDHCI_SDMA=y
  CONFIG_MMC_SDHCI_ROCKCHIP=y
  CONFIG_ETH_DESIGNWARE=y
  CONFIG_GMAC_ROCKCHIP=y
+CONFIG_PHY_ROCKCHIP_INNO_USB2=y
  CONFIG_REGULATOR_PWM=y
+CONFIG_DM_REGULATOR_FIXED=y
  CONFIG_PWM_ROCKCHIP=y
  CONFIG_SPL_RAM=y
  CONFIG_BAUDRATE=1500000
@@ -69,4 +73,17 @@ CONFIG_DEBUG_UART_SHIFT=2
  CONFIG_DEBUG_UART_ANNOUNCE=y
  CONFIG_SYSRESET=y
  # CONFIG_BINMAN_FDT is not set
+CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_GENERIC=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_OHCI_GENERIC=y
+CONFIG_USB_HOST_ETHER=y
+CONFIG_USB_ETHER_ASIX=y
+CONFIG_USB_ETHER_ASIX88179=y
+CONFIG_USB_ETHER_LAN75XX=y
+CONFIG_USB_ETHER_LAN78XX=y
+CONFIG_USB_ETHER_MCS7830=y
+CONFIG_USB_ETHER_RTL8152=y
+CONFIG_USB_ETHER_SMSC95XX=y
  CONFIG_ERRNO_STR=y
#3 lore raw

PATCH v5 3/6 phy: add support for phy-supply

In reply to Eugen Hristev

Some phys require a phy-supply property that is a phandle to a regulator that needs to be enabled for phy operations.
Implement basic supply lookup, enable and disabling, if DM_REGULATOR is available.

[[email protected]:
use regulator_set_enable_if_allowed and disable if power_on ops fails]

---
Changes in v5:
- add changes done by Jonas

 drivers/phy/phy-uclass.c | 51 +++++++++++++++++++++++++++++++---------
 1 file changed, 40 insertions(+), 11 deletions(-)
drivers/phy/phy-uclass.c +40 -11
index 3fef5135a9cb..45ec1471d0ae 100644
@@ -12,6 +12,7 @@
 #include <dm/devres.h>
 #include <generic-phy.h>
 #include <linux/list.h>
+#include <power/regulator.h>
 
 /**
  * struct phy_counts - Init and power-on counts of a single PHY port
@@ -29,12 +30,14 @@
  *              without a matching generic_phy_exit() afterwards
  * @list: Handle for a linked list of these structures corresponding to
  *        ports of the same PHY provider
+ * @supply: Handle to a phy-supply device
  */
 struct phy_counts {
 	unsigned long id;
 	int power_on_count;
 	int init_count;
 	struct list_head list;
+	struct udevice *supply;
 };
 
 static inline struct phy_ops *phy_dev_ops(struct udevice *dev)
@@ -58,7 +61,7 @@ static struct phy_counts *phy_get_counts(struct phy *phy)
 	return NULL;
 }
 
-static int phy_alloc_counts(struct phy *phy)
+static int phy_alloc_counts(struct phy *phy, struct udevice *supply)
 {
 	struct list_head *uc_priv;
 	struct phy_counts *counts;
@@ -76,6 +79,7 @@ static int phy_alloc_counts(struct phy *phy)
 	counts->id = phy->id;
 	counts->power_on_count = 0;
 	counts->init_count = 0;
+	counts->supply = supply;
 	list_add(&counts->list, uc_priv);
 
 	return 0;
@@ -123,7 +127,7 @@ int generic_phy_get_by_index_nodev(ofnode node, int index, struct phy *phy)
 {
 	struct ofnode_phandle_args args;
 	struct phy_ops *ops;
-	struct udevice *phydev;
+	struct udevice *phydev, *supply = NULL;
 	int i, ret;
 
 	debug("%s(node=%s, index=%d, phy=%p)\n",
@@ -172,7 +176,17 @@ int generic_phy_get_by_index_nodev(ofnode node, int index, struct phy *phy)
 		goto err;
 	}
 
-	ret = phy_alloc_counts(phy);
+	if (CONFIG_IS_ENABLED(DM_REGULATOR)) {
+		ret = device_get_supply_regulator(phydev, "phy-supply",
+						  &supply);
+		if (ret && ret != -ENOENT) {
+			debug("%s: device_get_supply_regulator failed: %d\n",
+			      __func__, ret);
+			goto err;
+		}
+	}
+
+	ret = phy_alloc_counts(phy, supply);
 	if (ret) {
 		debug("phy_alloc_counts() failed: %d\n", ret);
 		goto err;
@@ -300,14 +314,23 @@ int generic_phy_power_on(struct phy *phy)
 		return 0;
 	}
 
+	ret = regulator_set_enable_if_allowed(counts->supply, true);
+	if (ret && ret != -ENOSYS) {
+		dev_err(phy->dev, "PHY: Failed to enable regulator %s: %d.\n",
+			counts->supply->name, ret);
+		return ret;
+	}
+
 	ret = ops->power_on(phy);
-	if (ret)
+	if (ret) {
 		dev_err(phy->dev, "PHY: Failed to power on %s: %d.\n",
 			phy->dev->name, ret);
-	else
-		counts->power_on_count = 1;
+		regulator_set_enable_if_allowed(counts->supply, false);
+		return ret;
+	}
+	counts->power_on_count = 1;
 
-	return ret;
+	return 0;
 }
 
 int generic_phy_power_off(struct phy *phy)
@@ -331,13 +354,19 @@ int generic_phy_power_off(struct phy *phy)
 	}
 
 	ret = ops->power_off(phy);
-	if (ret)
+	if (ret) {
 		dev_err(phy->dev, "PHY: Failed to power off %s: %d.\n",
 			phy->dev->name, ret);
-	else
-		counts->power_on_count = 0;
+		return ret;
+	}
+	counts->power_on_count = 0;
 
-	return ret;
+	ret = regulator_set_enable_if_allowed(counts->supply, false);
+	if (ret && ret != -ENOSYS)
+		dev_err(phy->dev, "PHY: Failed to disable regulator %s: %d.\n",
+			counts->supply->name, ret);
+
+	return 0;
 }
 
 int generic_phy_configure(struct phy *phy, void *params)
Signature · 1 line
2.34.1
Reviewed-by on v5 3/6
#4 lore raw

Re: [PATCH v5 3/6] phy: add support for phy-supply

Quoted 9 lines · Eugen Hristev

Some phys require a phy-supply property that is a phandle to a regulator that needs to be enabled for phy operations.
Implement basic supply lookup, enable and disabling, if DM_REGULATOR is available.

[[email protected]:
use regulator_set_enable_if_allowed and disable if power_on ops fails]

Thanks,
- Kever

Quoted 131 lines

---
Changes in v5:
- add changes done by Jonas

  drivers/phy/phy-uclass.c | 51 +++++++++++++++++++++++++++++++---------
  1 file changed, 40 insertions(+), 11 deletions(-)
drivers/phy/phy-uclass.c +40 -11
index 3fef5135a9cb..45ec1471d0ae 100644
@@ -12,6 +12,7 @@
  #include <dm/devres.h>
  #include <generic-phy.h>
  #include <linux/list.h>
+#include <power/regulator.h>
 
  /**
   * struct phy_counts - Init and power-on counts of a single PHY port
@@ -29,12 +30,14 @@
   *              without a matching generic_phy_exit() afterwards
   * @list: Handle for a linked list of these structures corresponding to
   *        ports of the same PHY provider
+ * @supply: Handle to a phy-supply device
   */
  struct phy_counts {
  	unsigned long id;
  	int power_on_count;
  	int init_count;
  	struct list_head list;
+	struct udevice *supply;
  };
 
  static inline struct phy_ops *phy_dev_ops(struct udevice *dev)
@@ -58,7 +61,7 @@ static struct phy_counts *phy_get_counts(struct phy *phy)
  	return NULL;
  }
 
-static int phy_alloc_counts(struct phy *phy)
+static int phy_alloc_counts(struct phy *phy, struct udevice *supply)
  {
  	struct list_head *uc_priv;
  	struct phy_counts *counts;
@@ -76,6 +79,7 @@ static int phy_alloc_counts(struct phy *phy)
  	counts->id = phy->id;
  	counts->power_on_count = 0;
  	counts->init_count = 0;
+	counts->supply = supply;
  	list_add(&counts->list, uc_priv);
 
  	return 0;
@@ -123,7 +127,7 @@ int generic_phy_get_by_index_nodev(ofnode node, int index, struct phy *phy)
  {
  	struct ofnode_phandle_args args;
  	struct phy_ops *ops;
-	struct udevice *phydev;
+	struct udevice *phydev, *supply = NULL;
  	int i, ret;
 
  	debug("%s(node=%s, index=%d, phy=%p)\n",
@@ -172,7 +176,17 @@ int generic_phy_get_by_index_nodev(ofnode node, int index, struct phy *phy)
  		goto err;
  	}
 
-	ret = phy_alloc_counts(phy);
+	if (CONFIG_IS_ENABLED(DM_REGULATOR)) {
+		ret = device_get_supply_regulator(phydev, "phy-supply",
+						  &supply);
+		if (ret && ret != -ENOENT) {
+			debug("%s: device_get_supply_regulator failed: %d\n",
+			      __func__, ret);
+			goto err;
+		}
+	}
+
+	ret = phy_alloc_counts(phy, supply);
  	if (ret) {
  		debug("phy_alloc_counts() failed: %d\n", ret);
  		goto err;
@@ -300,14 +314,23 @@ int generic_phy_power_on(struct phy *phy)
  		return 0;
  	}
 
+	ret = regulator_set_enable_if_allowed(counts->supply, true);
+	if (ret && ret != -ENOSYS) {
+		dev_err(phy->dev, "PHY: Failed to enable regulator %s: %d.\n",
+			counts->supply->name, ret);
+		return ret;
+	}
+
  	ret = ops->power_on(phy);
-	if (ret)
+	if (ret) {
  		dev_err(phy->dev, "PHY: Failed to power on %s: %d.\n",
  			phy->dev->name, ret);
-	else
-		counts->power_on_count = 1;
+		regulator_set_enable_if_allowed(counts->supply, false);
+		return ret;
+	}
+	counts->power_on_count = 1;
 
-	return ret;
+	return 0;
  }
 
  int generic_phy_power_off(struct phy *phy)
@@ -331,13 +354,19 @@ int generic_phy_power_off(struct phy *phy)
  	}
 
  	ret = ops->power_off(phy);
-	if (ret)
+	if (ret) {
  		dev_err(phy->dev, "PHY: Failed to power off %s: %d.\n",
  			phy->dev->name, ret);
-	else
-		counts->power_on_count = 0;
+		return ret;
+	}
+	counts->power_on_count = 0;
 
-	return ret;
+	ret = regulator_set_enable_if_allowed(counts->supply, false);
+	if (ret && ret != -ENOSYS)
+		dev_err(phy->dev, "PHY: Failed to disable regulator %s: %d.\n",
+			counts->supply->name, ret);
+
+	return 0;
  }
 
  int generic_phy_configure(struct phy *phy, void *params)
#5 lore raw

PATCH v5 4/6 phy: remove phy-supply related code

In reply to Eugen Hristev

phy-supply is now handled at uclass level. Remove it from the drivers that implement it at the driver level.

---
 drivers/phy/meson-g12a-usb2.c | 48 -----------------------------------
 drivers/phy/meson-gxbb-usb2.c | 38 ---------------------------
 drivers/phy/meson-gxl-usb2.c  | 30 ----------------------
 3 files changed, 116 deletions(-)
drivers/phy/meson-g12a-usb2.c +0 -48
index 2fbba7fdae01..650b88bd1803 100644
@@ -54,50 +54,12 @@
 
 struct phy_meson_g12a_usb2_priv {
 	struct regmap		*regmap;
-#if CONFIG_IS_ENABLED(DM_REGULATOR)
-	struct udevice		*phy_supply;
-#endif
 #if CONFIG_IS_ENABLED(CLK)
 	struct clk		clk;
 #endif
 	struct reset_ctl	reset;
 };
 
-
-static int phy_meson_g12a_usb2_power_on(struct phy *phy)
-{
-#if CONFIG_IS_ENABLED(DM_REGULATOR)
-	struct udevice *dev = phy->dev;
-	struct phy_meson_g12a_usb2_priv *priv = dev_get_priv(dev);
-
-	if (priv->phy_supply) {
-		int ret = regulator_set_enable(priv->phy_supply, true);
-		if (ret)
-			return ret;
-	}
-#endif
-
-	return 0;
-}
-
-static int phy_meson_g12a_usb2_power_off(struct phy *phy)
-{
-#if CONFIG_IS_ENABLED(DM_REGULATOR)
-	struct udevice *dev = phy->dev;
-	struct phy_meson_g12a_usb2_priv *priv = dev_get_priv(dev);
-
-	if (priv->phy_supply) {
-		int ret = regulator_set_enable(priv->phy_supply, false);
-		if (ret) {
-			pr_err("Error disabling PHY supply\n");
-			return ret;
-		}
-	}
-#endif
-
-	return 0;
-}
-
 static int phy_meson_g12a_usb2_init(struct phy *phy)
 {
 	struct udevice *dev = phy->dev;
@@ -155,8 +117,6 @@ static int phy_meson_g12a_usb2_exit(struct phy *phy)
 struct phy_ops meson_g12a_usb2_phy_ops = {
 	.init = phy_meson_g12a_usb2_init,
 	.exit = phy_meson_g12a_usb2_exit,
-	.power_on = phy_meson_g12a_usb2_power_on,
-	.power_off = phy_meson_g12a_usb2_power_off,
 };
 
 int meson_g12a_usb2_phy_probe(struct udevice *dev)
@@ -193,14 +153,6 @@ int meson_g12a_usb2_phy_probe(struct udevice *dev)
 	}
 #endif
 
-#if CONFIG_IS_ENABLED(DM_REGULATOR)
-	ret = device_get_supply_regulator(dev, "phy-supply", &priv->phy_supply);
-	if (ret && ret != -ENOENT) {
-		pr_err("Failed to get PHY regulator\n");
-		return ret;
-	}
-#endif
-
 	return 0;
 }
 
drivers/phy/meson-gxbb-usb2.c +0 -38
index 7a2e3d2739e8..70a80b863819 100644
@@ -12,7 +12,6 @@
 #include <clk.h>
 #include <dm.h>
 #include <generic-phy.h>
-#include <power/regulator.h>
 #include <regmap.h>
 #include <reset.h>
 #include <linux/bitops.h>
@@ -81,9 +80,6 @@
 struct phy_meson_gxbb_usb2_priv {
 	struct regmap *regmap;
 	struct reset_ctl_bulk resets;
-#if CONFIG_IS_ENABLED(DM_REGULATOR)
-	struct udevice *phy_supply;
-#endif
 };
 
 static int phy_meson_gxbb_usb2_power_on(struct phy *phy)
@@ -92,15 +88,6 @@ static int phy_meson_gxbb_usb2_power_on(struct phy *phy)
 	struct phy_meson_gxbb_usb2_priv *priv = dev_get_priv(dev);
 	uint val;
 
-#if CONFIG_IS_ENABLED(DM_REGULATOR)
-	if (priv->phy_supply) {
-		int ret = regulator_set_enable(priv->phy_supply, true);
-
-		if (ret)
-			return ret;
-	}
-#endif
-
 	regmap_update_bits(priv->regmap, REG_CONFIG,
 			   REG_CONFIG_CLK_32k_ALTSEL,
 			   REG_CONFIG_CLK_32k_ALTSEL);
@@ -140,26 +127,8 @@ static int phy_meson_gxbb_usb2_power_on(struct phy *phy)
 	return 0;
 }
 
-static int phy_meson_gxbb_usb2_power_off(struct phy *phy)
-{
-#if CONFIG_IS_ENABLED(DM_REGULATOR)
-	struct udevice *dev = phy->dev;
-	struct phy_meson_gxbb_usb2_priv *priv = dev_get_priv(dev);
-
-	if (priv->phy_supply) {
-		int ret = regulator_set_enable(priv->phy_supply, false);
-
-		if (ret)
-			return ret;
-	}
-#endif
-
-	return 0;
-}
-
 static struct phy_ops meson_gxbb_usb2_phy_ops = {
 	.power_on = phy_meson_gxbb_usb2_power_on,
-	.power_off = phy_meson_gxbb_usb2_power_off,
 };
 
 static int meson_gxbb_usb2_phy_probe(struct udevice *dev)
@@ -192,13 +161,6 @@ static int meson_gxbb_usb2_phy_probe(struct udevice *dev)
 		return ret;
 	}
 
-#if CONFIG_IS_ENABLED(DM_REGULATOR)
-	ret = device_get_supply_regulator(dev, "phy-supply", &priv->phy_supply);
-	if (ret && ret != -ENOENT) {
-		pr_err("Failed to get PHY regulator\n");
-		return ret;
-	}
-#endif
 	ret = reset_get_bulk(dev, &priv->resets);
 	if (!ret) {
 		ret = reset_deassert_bulk(&priv->resets);
drivers/phy/meson-gxl-usb2.c +0 -30
index 9fb376cec448..4c631310efac 100644
@@ -16,7 +16,6 @@
 #include <generic-phy.h>
 #include <regmap.h>
 #include <linux/delay.h>
-#include <power/regulator.h>
 #include <clk.h>
 #include <linux/usb/otg.h>
 
@@ -101,9 +100,6 @@
 
 struct phy_meson_gxl_usb2_priv {
 	struct regmap		*regmap;
-#if CONFIG_IS_ENABLED(DM_REGULATOR)
-	struct udevice		*phy_supply;
-#endif
 #if CONFIG_IS_ENABLED(CLK)
 	struct clk		clk;
 #endif
@@ -167,14 +163,6 @@ static int phy_meson_gxl_usb2_power_on(struct phy *phy)
 
 	phy_meson_gxl_usb2_set_mode(phy, USB_DR_MODE_HOST);
 
-#if CONFIG_IS_ENABLED(DM_REGULATOR)
-	if (priv->phy_supply) {
-		int ret = regulator_set_enable(priv->phy_supply, true);
-		if (ret)
-			return ret;
-	}
-#endif
-
 	return 0;
 }
 
@@ -189,16 +177,6 @@ static int phy_meson_gxl_usb2_power_off(struct phy *phy)
 	val |= U2P_R0_POWER_ON_RESET;
 	regmap_write(priv->regmap, U2P_R0, val);
 
-#if CONFIG_IS_ENABLED(DM_REGULATOR)
-	if (priv->phy_supply) {
-		int ret = regulator_set_enable(priv->phy_supply, false);
-		if (ret) {
-			pr_err("Error disabling PHY supply\n");
-			return ret;
-		}
-	}
-#endif
-
 	return 0;
 }
 
@@ -229,14 +207,6 @@ int meson_gxl_usb2_phy_probe(struct udevice *dev)
 	}
 #endif
 
-#if CONFIG_IS_ENABLED(DM_REGULATOR)
-	ret = device_get_supply_regulator(dev, "phy-supply", &priv->phy_supply);
-	if (ret && ret != -ENOENT) {
-		pr_err("Failed to get PHY regulator\n");
-		return ret;
-	}
-#endif
-
 	return 0;
 }
 
Signature · 1 line
2.34.1
#6 lore raw

Re: [PATCH v5 4/6] phy: remove phy-supply related code

Hi Neil,

    Could you take a look at this patch?

Thanks,

- Kever

Quoted 238 lines · Eugen Hristev

phy-supply is now handled at uclass level. Remove it from the drivers that implement it at the driver level.

---
  drivers/phy/meson-g12a-usb2.c | 48 -----------------------------------
  drivers/phy/meson-gxbb-usb2.c | 38 ---------------------------
  drivers/phy/meson-gxl-usb2.c  | 30 ----------------------
  3 files changed, 116 deletions(-)
drivers/phy/meson-g12a-usb2.c +0 -48
index 2fbba7fdae01..650b88bd1803 100644
@@ -54,50 +54,12 @@
 
  struct phy_meson_g12a_usb2_priv {
  	struct regmap		*regmap;
-#if CONFIG_IS_ENABLED(DM_REGULATOR)
-	struct udevice		*phy_supply;
-#endif
  #if CONFIG_IS_ENABLED(CLK)
  	struct clk		clk;
  #endif
  	struct reset_ctl	reset;
  };
 
-
-static int phy_meson_g12a_usb2_power_on(struct phy *phy)
-{
-#if CONFIG_IS_ENABLED(DM_REGULATOR)
-	struct udevice *dev = phy->dev;
-	struct phy_meson_g12a_usb2_priv *priv = dev_get_priv(dev);
-
-	if (priv->phy_supply) {
-		int ret = regulator_set_enable(priv->phy_supply, true);
-		if (ret)
-			return ret;
-	}
-#endif
-
-	return 0;
-}
-
-static int phy_meson_g12a_usb2_power_off(struct phy *phy)
-{
-#if CONFIG_IS_ENABLED(DM_REGULATOR)
-	struct udevice *dev = phy->dev;
-	struct phy_meson_g12a_usb2_priv *priv = dev_get_priv(dev);
-
-	if (priv->phy_supply) {
-		int ret = regulator_set_enable(priv->phy_supply, false);
-		if (ret) {
-			pr_err("Error disabling PHY supply\n");
-			return ret;
-		}
-	}
-#endif
-
-	return 0;
-}
-
  static int phy_meson_g12a_usb2_init(struct phy *phy)
  {
  	struct udevice *dev = phy->dev;
@@ -155,8 +117,6 @@ static int phy_meson_g12a_usb2_exit(struct phy *phy)
  struct phy_ops meson_g12a_usb2_phy_ops = {
  	.init = phy_meson_g12a_usb2_init,
  	.exit = phy_meson_g12a_usb2_exit,
-	.power_on = phy_meson_g12a_usb2_power_on,
-	.power_off = phy_meson_g12a_usb2_power_off,
  };
 
  int meson_g12a_usb2_phy_probe(struct udevice *dev)
@@ -193,14 +153,6 @@ int meson_g12a_usb2_phy_probe(struct udevice *dev)
  	}
  #endif
 
-#if CONFIG_IS_ENABLED(DM_REGULATOR)
-	ret = device_get_supply_regulator(dev, "phy-supply", &priv->phy_supply);
-	if (ret && ret != -ENOENT) {
-		pr_err("Failed to get PHY regulator\n");
-		return ret;
-	}
-#endif
-
  	return 0;
  }
 
drivers/phy/meson-gxbb-usb2.c +0 -38
index 7a2e3d2739e8..70a80b863819 100644
@@ -12,7 +12,6 @@
  #include <clk.h>
  #include <dm.h>
  #include <generic-phy.h>
-#include <power/regulator.h>
  #include <regmap.h>
  #include <reset.h>
  #include <linux/bitops.h>
@@ -81,9 +80,6 @@
  struct phy_meson_gxbb_usb2_priv {
  	struct regmap *regmap;
  	struct reset_ctl_bulk resets;
-#if CONFIG_IS_ENABLED(DM_REGULATOR)
-	struct udevice *phy_supply;
-#endif
  };
 
  static int phy_meson_gxbb_usb2_power_on(struct phy *phy)
@@ -92,15 +88,6 @@ static int phy_meson_gxbb_usb2_power_on(struct phy *phy)
  	struct phy_meson_gxbb_usb2_priv *priv = dev_get_priv(dev);
  	uint val;
 
-#if CONFIG_IS_ENABLED(DM_REGULATOR)
-	if (priv->phy_supply) {
-		int ret = regulator_set_enable(priv->phy_supply, true);
-
-		if (ret)
-			return ret;
-	}
-#endif
-
  	regmap_update_bits(priv->regmap, REG_CONFIG,
  			   REG_CONFIG_CLK_32k_ALTSEL,
  			   REG_CONFIG_CLK_32k_ALTSEL);
@@ -140,26 +127,8 @@ static int phy_meson_gxbb_usb2_power_on(struct phy *phy)
  	return 0;
  }
 
-static int phy_meson_gxbb_usb2_power_off(struct phy *phy)
-{
-#if CONFIG_IS_ENABLED(DM_REGULATOR)
-	struct udevice *dev = phy->dev;
-	struct phy_meson_gxbb_usb2_priv *priv = dev_get_priv(dev);
-
-	if (priv->phy_supply) {
-		int ret = regulator_set_enable(priv->phy_supply, false);
-
-		if (ret)
-			return ret;
-	}
-#endif
-
-	return 0;
-}
-
  static struct phy_ops meson_gxbb_usb2_phy_ops = {
  	.power_on = phy_meson_gxbb_usb2_power_on,
-	.power_off = phy_meson_gxbb_usb2_power_off,
  };
 
  static int meson_gxbb_usb2_phy_probe(struct udevice *dev)
@@ -192,13 +161,6 @@ static int meson_gxbb_usb2_phy_probe(struct udevice *dev)
  		return ret;
  	}
 
-#if CONFIG_IS_ENABLED(DM_REGULATOR)
-	ret = device_get_supply_regulator(dev, "phy-supply", &priv->phy_supply);
-	if (ret && ret != -ENOENT) {
-		pr_err("Failed to get PHY regulator\n");
-		return ret;
-	}
-#endif
  	ret = reset_get_bulk(dev, &priv->resets);
  	if (!ret) {
  		ret = reset_deassert_bulk(&priv->resets);
drivers/phy/meson-gxl-usb2.c +0 -30
index 9fb376cec448..4c631310efac 100644
@@ -16,7 +16,6 @@
  #include <generic-phy.h>
  #include <regmap.h>
  #include <linux/delay.h>
-#include <power/regulator.h>
  #include <clk.h>
  #include <linux/usb/otg.h>
 
@@ -101,9 +100,6 @@
 
  struct phy_meson_gxl_usb2_priv {
  	struct regmap		*regmap;
-#if CONFIG_IS_ENABLED(DM_REGULATOR)
-	struct udevice		*phy_supply;
-#endif
  #if CONFIG_IS_ENABLED(CLK)
  	struct clk		clk;
  #endif
@@ -167,14 +163,6 @@ static int phy_meson_gxl_usb2_power_on(struct phy *phy)
 
  	phy_meson_gxl_usb2_set_mode(phy, USB_DR_MODE_HOST);
 
-#if CONFIG_IS_ENABLED(DM_REGULATOR)
-	if (priv->phy_supply) {
-		int ret = regulator_set_enable(priv->phy_supply, true);
-		if (ret)
-			return ret;
-	}
-#endif
-
  	return 0;
  }
 
@@ -189,16 +177,6 @@ static int phy_meson_gxl_usb2_power_off(struct phy *phy)
  	val |= U2P_R0_POWER_ON_RESET;
  	regmap_write(priv->regmap, U2P_R0, val);
 
-#if CONFIG_IS_ENABLED(DM_REGULATOR)
-	if (priv->phy_supply) {
-		int ret = regulator_set_enable(priv->phy_supply, false);
-		if (ret) {
-			pr_err("Error disabling PHY supply\n");
-			return ret;
-		}
-	}
-#endif
-
  	return 0;
  }
 
@@ -229,14 +207,6 @@ int meson_gxl_usb2_phy_probe(struct udevice *dev)
  	}
  #endif
 
-#if CONFIG_IS_ENABLED(DM_REGULATOR)
-	ret = device_get_supply_regulator(dev, "phy-supply", &priv->phy_supply);
-	if (ret && ret != -ENOENT) {
-		pr_err("Failed to get PHY regulator\n");
-		return ret;
-	}
-#endif
-
  	return 0;
  }
 
maintainer Acked-by on v5 4/6
#7 lore raw

Re: [PATCH v5 4/6] phy: remove phy-supply related code

In reply to Eugen Hristev
Quoted 228 lines · Eugen Hristev

phy-supply is now handled at uclass level. Remove it from the drivers that implement it at the driver level.

---
  drivers/phy/meson-g12a-usb2.c | 48 -----------------------------------
  drivers/phy/meson-gxbb-usb2.c | 38 ---------------------------
  drivers/phy/meson-gxl-usb2.c  | 30 ----------------------
  3 files changed, 116 deletions(-)
drivers/phy/meson-g12a-usb2.c +0 -48
index 2fbba7fdae01..650b88bd1803 100644
@@ -54,50 +54,12 @@
 
  struct phy_meson_g12a_usb2_priv {
  	struct regmap		*regmap;
-#if CONFIG_IS_ENABLED(DM_REGULATOR)
-	struct udevice		*phy_supply;
-#endif
  #if CONFIG_IS_ENABLED(CLK)
  	struct clk		clk;
  #endif
  	struct reset_ctl	reset;
  };
 
-
-static int phy_meson_g12a_usb2_power_on(struct phy *phy)
-{
-#if CONFIG_IS_ENABLED(DM_REGULATOR)
-	struct udevice *dev = phy->dev;
-	struct phy_meson_g12a_usb2_priv *priv = dev_get_priv(dev);
-
-	if (priv->phy_supply) {
-		int ret = regulator_set_enable(priv->phy_supply, true);
-		if (ret)
-			return ret;
-	}
-#endif
-
-	return 0;
-}
-
-static int phy_meson_g12a_usb2_power_off(struct phy *phy)
-{
-#if CONFIG_IS_ENABLED(DM_REGULATOR)
-	struct udevice *dev = phy->dev;
-	struct phy_meson_g12a_usb2_priv *priv = dev_get_priv(dev);
-
-	if (priv->phy_supply) {
-		int ret = regulator_set_enable(priv->phy_supply, false);
-		if (ret) {
-			pr_err("Error disabling PHY supply\n");
-			return ret;
-		}
-	}
-#endif
-
-	return 0;
-}
-
  static int phy_meson_g12a_usb2_init(struct phy *phy)
  {
  	struct udevice *dev = phy->dev;
@@ -155,8 +117,6 @@ static int phy_meson_g12a_usb2_exit(struct phy *phy)
  struct phy_ops meson_g12a_usb2_phy_ops = {
  	.init = phy_meson_g12a_usb2_init,
  	.exit = phy_meson_g12a_usb2_exit,
-	.power_on = phy_meson_g12a_usb2_power_on,
-	.power_off = phy_meson_g12a_usb2_power_off,
  };
 
  int meson_g12a_usb2_phy_probe(struct udevice *dev)
@@ -193,14 +153,6 @@ int meson_g12a_usb2_phy_probe(struct udevice *dev)
  	}
  #endif
 
-#if CONFIG_IS_ENABLED(DM_REGULATOR)
-	ret = device_get_supply_regulator(dev, "phy-supply", &priv->phy_supply);
-	if (ret && ret != -ENOENT) {
-		pr_err("Failed to get PHY regulator\n");
-		return ret;
-	}
-#endif
-
  	return 0;
  }
 
drivers/phy/meson-gxbb-usb2.c +0 -38
index 7a2e3d2739e8..70a80b863819 100644
@@ -12,7 +12,6 @@
  #include <clk.h>
  #include <dm.h>
  #include <generic-phy.h>
-#include <power/regulator.h>
  #include <regmap.h>
  #include <reset.h>
  #include <linux/bitops.h>
@@ -81,9 +80,6 @@
  struct phy_meson_gxbb_usb2_priv {
  	struct regmap *regmap;
  	struct reset_ctl_bulk resets;
-#if CONFIG_IS_ENABLED(DM_REGULATOR)
-	struct udevice *phy_supply;
-#endif
  };
 
  static int phy_meson_gxbb_usb2_power_on(struct phy *phy)
@@ -92,15 +88,6 @@ static int phy_meson_gxbb_usb2_power_on(struct phy *phy)
  	struct phy_meson_gxbb_usb2_priv *priv = dev_get_priv(dev);
  	uint val;
 
-#if CONFIG_IS_ENABLED(DM_REGULATOR)
-	if (priv->phy_supply) {
-		int ret = regulator_set_enable(priv->phy_supply, true);
-
-		if (ret)
-			return ret;
-	}
-#endif
-
  	regmap_update_bits(priv->regmap, REG_CONFIG,
  			   REG_CONFIG_CLK_32k_ALTSEL,
  			   REG_CONFIG_CLK_32k_ALTSEL);
@@ -140,26 +127,8 @@ static int phy_meson_gxbb_usb2_power_on(struct phy *phy)
  	return 0;
  }
 
-static int phy_meson_gxbb_usb2_power_off(struct phy *phy)
-{
-#if CONFIG_IS_ENABLED(DM_REGULATOR)
-	struct udevice *dev = phy->dev;
-	struct phy_meson_gxbb_usb2_priv *priv = dev_get_priv(dev);
-
-	if (priv->phy_supply) {
-		int ret = regulator_set_enable(priv->phy_supply, false);
-
-		if (ret)
-			return ret;
-	}
-#endif
-
-	return 0;
-}
-
  static struct phy_ops meson_gxbb_usb2_phy_ops = {
  	.power_on = phy_meson_gxbb_usb2_power_on,
-	.power_off = phy_meson_gxbb_usb2_power_off,
  };
 
  static int meson_gxbb_usb2_phy_probe(struct udevice *dev)
@@ -192,13 +161,6 @@ static int meson_gxbb_usb2_phy_probe(struct udevice *dev)
  		return ret;
  	}
 
-#if CONFIG_IS_ENABLED(DM_REGULATOR)
-	ret = device_get_supply_regulator(dev, "phy-supply", &priv->phy_supply);
-	if (ret && ret != -ENOENT) {
-		pr_err("Failed to get PHY regulator\n");
-		return ret;
-	}
-#endif
  	ret = reset_get_bulk(dev, &priv->resets);
  	if (!ret) {
  		ret = reset_deassert_bulk(&priv->resets);
drivers/phy/meson-gxl-usb2.c +0 -23
index 9fb376cec448..4c631310efac 100644
@@ -16,7 +16,6 @@
  #include <generic-phy.h>
  #include <regmap.h>
  #include <linux/delay.h>
-#include <power/regulator.h>
  #include <clk.h>
  #include <linux/usb/otg.h>
 
@@ -101,9 +100,6 @@
 
  struct phy_meson_gxl_usb2_priv {
  	struct regmap		*regmap;
-#if CONFIG_IS_ENABLED(DM_REGULATOR)
-	struct udevice		*phy_supply;
-#endif
  #if CONFIG_IS_ENABLED(CLK)
  	struct clk		clk;
  #endif
@@ -167,14 +163,6 @@ static int phy_meson_gxl_usb2_power_on(struct phy *phy)
 
  	phy_meson_gxl_usb2_set_mode(phy, USB_DR_MODE_HOST);
 
-#if CONFIG_IS_ENABLED(DM_REGULATOR)
-	if (priv->phy_supply) {
-		int ret = regulator_set_enable(priv->phy_supply, true);
-		if (ret)
-			return ret;
-	}
-#endif
-
  	return 0;
  }
 
@@ -189,16 +177,6 @@ static int phy_meson_gxl_usb2_power_off(struct phy *phy)
  	val |= U2P_R0_POWER_ON_RESET;
  	regmap_write(priv->regmap, U2P_R0, val);
 
-#if CONFIG_IS_ENABLED(DM_REGULATOR)
-	if (priv->phy_supply) {
-		int ret = regulator_set_enable(priv->phy_supply, false);
-		if (ret) {
-			pr_err("Error disabling PHY supply\n");
-			return ret;
-		}
-	}
-#endif
-
  	return 0;
  }
 
@@ -229,14 +207,6 @@ int meson_gxl_usb2_phy_probe(struct udevice *dev)
  	}
  #endif
 
-#if CONFIG_IS_ENABLED(DM_REGULATOR)

drivers/phy/meson-gxl-usb2.c int meson_gxl_usb2_phy_probe(struct udevice *dev) · line 212

Quoted 10 lines
drivers/phy/meson-gxl-usb2.c +0 -7
-	ret = device_get_supply_regulator(dev, "phy-supply", &priv->phy_supply);
-	if (ret && ret != -ENOENT) {
-		pr_err("Failed to get PHY regulator\n");
-		return ret;
-	}
-#endif
-
  	return 0;
  }
 
#8 lore raw

PATCH v5 5/6 phy: rockchip-inno-usb2: add initial support for rk3588 PHY

In reply to Eugen Hristev

Add initial support for the rk3588 PHY variant.
The lookup for the host-port reg inside the struct now does a do {} while() instead of a while() {} in order to allow a first check for reg == 0.

---
 drivers/phy/rockchip/phy-rockchip-inno-usb2.c | 60 ++++++++++++++++++-
 1 file changed, 58 insertions(+), 2 deletions(-)
drivers/phy/rockchip/phy-rockchip-inno-usb2.c +58 -2
index 55e1dbcfef7e..22e2797eea28 100644
@@ -201,14 +201,14 @@ static int rockchip_usb2phy_probe(struct udevice *dev)
 
 	/* find out a proper config which can be matched with dt. */
 	index = 0;
-	while (phy_cfgs[index].reg) {
+	do {
 		if (phy_cfgs[index].reg == reg) {
 			priv->phy_cfg = &phy_cfgs[index];
 			break;
 		}
 
 		++index;
-	}
+	} while (phy_cfgs[index].reg);
 
 	if (!priv->phy_cfg) {
 		dev_err(dev, "failed find proper phy-cfg\n");
@@ -348,6 +348,58 @@ static const struct rockchip_usb2phy_cfg rk3568_phy_cfgs[] = {
 	{ /* sentinel */ }
 };
 
+static const struct rockchip_usb2phy_cfg rk3588_phy_cfgs[] = {
+	{
+		.reg		= 0x0000,
+		.port_cfgs	= {
+			[USB2PHY_PORT_OTG] = {
+				.phy_sus	= { 0x000c, 11, 11, 0, 1 },
+				.ls_det_en	= { 0x0080, 0, 0, 0, 1 },
+				.ls_det_st	= { 0x0084, 0, 0, 0, 1 },
+				.ls_det_clr	= { 0x0088, 0, 0, 0, 1 },
+				.utmi_ls	= { 0x00c0, 10, 9, 0, 1 },
+			}
+		},
+	},
+	{
+		.reg		= 0x4000,
+		.port_cfgs	= {
+			[USB2PHY_PORT_OTG] = {
+				.phy_sus	= { 0x000c, 11, 11, 0, 0 },
+				.ls_det_en	= { 0x0080, 0, 0, 0, 1 },
+				.ls_det_st	= { 0x0084, 0, 0, 0, 1 },
+				.ls_det_clr	= { 0x0088, 0, 0, 0, 1 },
+				.utmi_ls	= { 0x00c0, 10, 9, 0, 1 },
+			}
+		},
+	},
+	{
+		.reg		= 0x8000,
+		.port_cfgs	= {
+			[USB2PHY_PORT_HOST] = {
+				.phy_sus	= { 0x0008, 2, 2, 0, 1 },
+				.ls_det_en	= { 0x0080, 0, 0, 0, 1 },
+				.ls_det_st	= { 0x0084, 0, 0, 0, 1 },
+				.ls_det_clr	= { 0x0088, 0, 0, 0, 1 },
+				.utmi_ls	= { 0x00c0, 10, 9, 0, 1 },
+			}
+		},
+	},
+	{
+		.reg		= 0xc000,
+		.port_cfgs	= {
+			[USB2PHY_PORT_HOST] = {
+				.phy_sus	= { 0x0008, 2, 2, 0, 1 },
+				.ls_det_en	= { 0x0080, 0, 0, 0, 1 },
+				.ls_det_st	= { 0x0084, 0, 0, 0, 1 },
+				.ls_det_clr	= { 0x0088, 0, 0, 0, 1 },
+				.utmi_ls	= { 0x00c0, 10, 9, 0, 1 },
+			}
+		},
+	},
+	{ /* sentinel */ }
+};
+
 static const struct udevice_id rockchip_usb2phy_ids[] = {
 	{
 		.compatible = "rockchip,rk3399-usb2phy",
@@ -357,6 +409,10 @@ static const struct udevice_id rockchip_usb2phy_ids[] = {
 		.compatible = "rockchip,rk3568-usb2phy",
 		.data = (ulong)&rk3568_phy_cfgs,
 	},
+	{
+		.compatible = "rockchip,rk3588-usb2phy",
+		.data = (ulong)&rk3588_phy_cfgs,
+	},
 	{ /* sentinel */ }
 };
 
Signature · 1 line
2.34.1
Reviewed-by on v5 5/6
#9 lore raw

Re: [PATCH v5 5/6] phy: rockchip-inno-usb2: add initial support for rk3588 PHY

Quoted 7 lines · Eugen Hristev

Add initial support for the rk3588 PHY variant.
The lookup for the host-port reg inside the struct now does a do {} while() instead of a while() {} in order to allow a first check for reg == 0.

Thanks,
- Kever

Quoted 95 lines
---
  drivers/phy/rockchip/phy-rockchip-inno-usb2.c | 60 ++++++++++++++++++-
  1 file changed, 58 insertions(+), 2 deletions(-)
drivers/phy/rockchip/phy-rockchip-inno-usb2.c +58 -2
index 55e1dbcfef7e..22e2797eea28 100644
@@ -201,14 +201,14 @@ static int rockchip_usb2phy_probe(struct udevice *dev)
 
  	/* find out a proper config which can be matched with dt. */
  	index = 0;
-	while (phy_cfgs[index].reg) {
+	do {
  		if (phy_cfgs[index].reg == reg) {
  			priv->phy_cfg = &phy_cfgs[index];
  			break;
  		}
 
  		++index;
-	}
+	} while (phy_cfgs[index].reg);
 
  	if (!priv->phy_cfg) {
  		dev_err(dev, "failed find proper phy-cfg\n");
@@ -348,6 +348,58 @@ static const struct rockchip_usb2phy_cfg rk3568_phy_cfgs[] = {
  	{ /* sentinel */ }
  };
 
+static const struct rockchip_usb2phy_cfg rk3588_phy_cfgs[] = {
+	{
+		.reg		= 0x0000,
+		.port_cfgs	= {
+			[USB2PHY_PORT_OTG] = {
+				.phy_sus	= { 0x000c, 11, 11, 0, 1 },
+				.ls_det_en	= { 0x0080, 0, 0, 0, 1 },
+				.ls_det_st	= { 0x0084, 0, 0, 0, 1 },
+				.ls_det_clr	= { 0x0088, 0, 0, 0, 1 },
+				.utmi_ls	= { 0x00c0, 10, 9, 0, 1 },
+			}
+		},
+	},
+	{
+		.reg		= 0x4000,
+		.port_cfgs	= {
+			[USB2PHY_PORT_OTG] = {
+				.phy_sus	= { 0x000c, 11, 11, 0, 0 },
+				.ls_det_en	= { 0x0080, 0, 0, 0, 1 },
+				.ls_det_st	= { 0x0084, 0, 0, 0, 1 },
+				.ls_det_clr	= { 0x0088, 0, 0, 0, 1 },
+				.utmi_ls	= { 0x00c0, 10, 9, 0, 1 },
+			}
+		},
+	},
+	{
+		.reg		= 0x8000,
+		.port_cfgs	= {
+			[USB2PHY_PORT_HOST] = {
+				.phy_sus	= { 0x0008, 2, 2, 0, 1 },
+				.ls_det_en	= { 0x0080, 0, 0, 0, 1 },
+				.ls_det_st	= { 0x0084, 0, 0, 0, 1 },
+				.ls_det_clr	= { 0x0088, 0, 0, 0, 1 },
+				.utmi_ls	= { 0x00c0, 10, 9, 0, 1 },
+			}
+		},
+	},
+	{
+		.reg		= 0xc000,
+		.port_cfgs	= {
+			[USB2PHY_PORT_HOST] = {
+				.phy_sus	= { 0x0008, 2, 2, 0, 1 },
+				.ls_det_en	= { 0x0080, 0, 0, 0, 1 },
+				.ls_det_st	= { 0x0084, 0, 0, 0, 1 },
+				.ls_det_clr	= { 0x0088, 0, 0, 0, 1 },
+				.utmi_ls	= { 0x00c0, 10, 9, 0, 1 },
+			}
+		},
+	},
+	{ /* sentinel */ }
+};
+
  static const struct udevice_id rockchip_usb2phy_ids[] = {
  	{
  		.compatible = "rockchip,rk3399-usb2phy",
@@ -357,6 +409,10 @@ static const struct udevice_id rockchip_usb2phy_ids[] = {
  		.compatible = "rockchip,rk3568-usb2phy",
  		.data = (ulong)&rk3568_phy_cfgs,
  	},
+	{
+		.compatible = "rockchip,rk3588-usb2phy",
+		.data = (ulong)&rk3588_phy_cfgs,
+	},
  	{ /* sentinel */ }
  };
 
#10 lore raw

PATCH v5 6/6 phy: Keep balance of counts when ops is missing

In reply to Eugen Hristev

From: Jonas Karlman <[email protected]>

Fixes 226fce6108fe ("phy: Track power-on and init counts in uclass")
---
 drivers/phy/phy-uclass.c | 80 ++++++++++++++++++++--------------------
 1 file changed, 39 insertions(+), 41 deletions(-)
drivers/phy/phy-uclass.c +39 -41
index 45ec1471d0ae..2a672549f268 100644
@@ -228,24 +228,24 @@ int generic_phy_init(struct phy *phy)
 
 	if (!generic_phy_valid(phy))
 		return 0;
-	ops = phy_dev_ops(phy->dev);
-	if (!ops->init)
-		return 0;
-
 	counts = phy_get_counts(phy);
 	if (counts->init_count > 0) {
 		counts->init_count++;
 		return 0;
 	}
 
-	ret = ops->init(phy);
-	if (ret)
-		dev_err(phy->dev, "PHY: Failed to init %s: %d.\n",
-			phy->dev->name, ret);
-	else
-		counts->init_count = 1;
+	ops = phy_dev_ops(phy->dev);
+	if (ops->init) {
+		ret = ops->init(phy);
+		if (ret) {
+			dev_err(phy->dev, "PHY: Failed to init %s: %d.\n",
+				phy->dev->name, ret);
+			return ret;
+		}
+	}
+	counts->init_count = 1;
 
-	return ret;
+	return 0;
 }
 
 int generic_phy_reset(struct phy *phy)
@@ -274,10 +274,6 @@ int generic_phy_exit(struct phy *phy)
 
 	if (!generic_phy_valid(phy))
 		return 0;
-	ops = phy_dev_ops(phy->dev);
-	if (!ops->exit)
-		return 0;
-
 	counts = phy_get_counts(phy);
 	if (counts->init_count == 0)
 		return 0;
@@ -286,14 +282,18 @@ int generic_phy_exit(struct phy *phy)
 		return 0;
 	}
 
-	ret = ops->exit(phy);
-	if (ret)
-		dev_err(phy->dev, "PHY: Failed to exit %s: %d.\n",
-			phy->dev->name, ret);
-	else
-		counts->init_count = 0;
+	ops = phy_dev_ops(phy->dev);
+	if (ops->exit) {
+		ret = ops->exit(phy);
+		if (ret) {
+			dev_err(phy->dev, "PHY: Failed to exit %s: %d.\n",
+				phy->dev->name, ret);
+			return ret;
+		}
+	}
+	counts->init_count = 0;
 
-	return ret;
+	return 0;
 }
 
 int generic_phy_power_on(struct phy *phy)
@@ -304,10 +304,6 @@ int generic_phy_power_on(struct phy *phy)
 
 	if (!generic_phy_valid(phy))
 		return 0;
-	ops = phy_dev_ops(phy->dev);
-	if (!ops->power_on)
-		return 0;
-
 	counts = phy_get_counts(phy);
 	if (counts->power_on_count > 0) {
 		counts->power_on_count++;
@@ -321,12 +317,15 @@ int generic_phy_power_on(struct phy *phy)
 		return ret;
 	}
 
-	ret = ops->power_on(phy);
-	if (ret) {
-		dev_err(phy->dev, "PHY: Failed to power on %s: %d.\n",
-			phy->dev->name, ret);
-		regulator_set_enable_if_allowed(counts->supply, false);
-		return ret;
+	ops = phy_dev_ops(phy->dev);
+	if (ops->power_on) {
+		ret = ops->power_on(phy);
+		if (ret) {
+			dev_err(phy->dev, "PHY: Failed to power on %s: %d.\n",
+				phy->dev->name, ret);
+			regulator_set_enable_if_allowed(counts->supply, false);
+			return ret;
+		}
 	}
 	counts->power_on_count = 1;
 
@@ -341,10 +340,6 @@ int generic_phy_power_off(struct phy *phy)
 
 	if (!generic_phy_valid(phy))
 		return 0;
-	ops = phy_dev_ops(phy->dev);
-	if (!ops->power_off)
-		return 0;
-
 	counts = phy_get_counts(phy);
 	if (counts->power_on_count == 0)
 		return 0;
@@ -353,11 +348,14 @@ int generic_phy_power_off(struct phy *phy)
 		return 0;
 	}
 
-	ret = ops->power_off(phy);
-	if (ret) {
-		dev_err(phy->dev, "PHY: Failed to power off %s: %d.\n",
-			phy->dev->name, ret);
-		return ret;
+	ops = phy_dev_ops(phy->dev);
+	if (ops->power_off) {
+		ret = ops->power_off(phy);
+		if (ret) {
+			dev_err(phy->dev, "PHY: Failed to power off %s: %d.\n",
+				phy->dev->name, ret);
+			return ret;
+		}
 	}
 	counts->power_on_count = 0;
 
Signature · 1 line
2.34.1
Reviewed-by on v5 6/6
#11 lore raw

Re: [PATCH v5 6/6] phy: Keep balance of counts when ops is missing

Quoted 4 lines · Eugen Hristev

From: Jonas Karlman <[email protected]>

Fixes 226fce6108fe ("phy: Track power-on and init counts in uclass")

Thanks,
- Kever

Quoted 145 lines
---
  drivers/phy/phy-uclass.c | 80 ++++++++++++++++++++--------------------
  1 file changed, 39 insertions(+), 41 deletions(-)
drivers/phy/phy-uclass.c +39 -41
index 45ec1471d0ae..2a672549f268 100644
@@ -228,24 +228,24 @@ int generic_phy_init(struct phy *phy)
 
  	if (!generic_phy_valid(phy))
  		return 0;
-	ops = phy_dev_ops(phy->dev);
-	if (!ops->init)
-		return 0;
-
  	counts = phy_get_counts(phy);
  	if (counts->init_count > 0) {
  		counts->init_count++;
  		return 0;
  	}
 
-	ret = ops->init(phy);
-	if (ret)
-		dev_err(phy->dev, "PHY: Failed to init %s: %d.\n",
-			phy->dev->name, ret);
-	else
-		counts->init_count = 1;
+	ops = phy_dev_ops(phy->dev);
+	if (ops->init) {
+		ret = ops->init(phy);
+		if (ret) {
+			dev_err(phy->dev, "PHY: Failed to init %s: %d.\n",
+				phy->dev->name, ret);
+			return ret;
+		}
+	}
+	counts->init_count = 1;
 
-	return ret;
+	return 0;
  }
 
  int generic_phy_reset(struct phy *phy)
@@ -274,10 +274,6 @@ int generic_phy_exit(struct phy *phy)
 
  	if (!generic_phy_valid(phy))
  		return 0;
-	ops = phy_dev_ops(phy->dev);
-	if (!ops->exit)
-		return 0;
-
  	counts = phy_get_counts(phy);
  	if (counts->init_count == 0)
  		return 0;
@@ -286,14 +282,18 @@ int generic_phy_exit(struct phy *phy)
  		return 0;
  	}
 
-	ret = ops->exit(phy);
-	if (ret)
-		dev_err(phy->dev, "PHY: Failed to exit %s: %d.\n",
-			phy->dev->name, ret);
-	else
-		counts->init_count = 0;
+	ops = phy_dev_ops(phy->dev);
+	if (ops->exit) {
+		ret = ops->exit(phy);
+		if (ret) {
+			dev_err(phy->dev, "PHY: Failed to exit %s: %d.\n",
+				phy->dev->name, ret);
+			return ret;
+		}
+	}
+	counts->init_count = 0;
 
-	return ret;
+	return 0;
  }
 
  int generic_phy_power_on(struct phy *phy)
@@ -304,10 +304,6 @@ int generic_phy_power_on(struct phy *phy)
 
  	if (!generic_phy_valid(phy))
  		return 0;
-	ops = phy_dev_ops(phy->dev);
-	if (!ops->power_on)
-		return 0;
-
  	counts = phy_get_counts(phy);
  	if (counts->power_on_count > 0) {
  		counts->power_on_count++;
@@ -321,12 +317,15 @@ int generic_phy_power_on(struct phy *phy)
  		return ret;
  	}
 
-	ret = ops->power_on(phy);
-	if (ret) {
-		dev_err(phy->dev, "PHY: Failed to power on %s: %d.\n",
-			phy->dev->name, ret);
-		regulator_set_enable_if_allowed(counts->supply, false);
-		return ret;
+	ops = phy_dev_ops(phy->dev);
+	if (ops->power_on) {
+		ret = ops->power_on(phy);
+		if (ret) {
+			dev_err(phy->dev, "PHY: Failed to power on %s: %d.\n",
+				phy->dev->name, ret);
+			regulator_set_enable_if_allowed(counts->supply, false);
+			return ret;
+		}
  	}
  	counts->power_on_count = 1;
 
@@ -341,10 +340,6 @@ int generic_phy_power_off(struct phy *phy)
 
  	if (!generic_phy_valid(phy))
  		return 0;
-	ops = phy_dev_ops(phy->dev);
-	if (!ops->power_off)
-		return 0;
-
  	counts = phy_get_counts(phy);
  	if (counts->power_on_count == 0)
  		return 0;
@@ -353,11 +348,14 @@ int generic_phy_power_off(struct phy *phy)
  		return 0;
  	}
 
-	ret = ops->power_off(phy);
-	if (ret) {
-		dev_err(phy->dev, "PHY: Failed to power off %s: %d.\n",
-			phy->dev->name, ret);
-		return ret;
+	ops = phy_dev_ops(phy->dev);
+	if (ops->power_off) {
+		ret = ops->power_off(phy);
+		if (ret) {
+			dev_err(phy->dev, "PHY: Failed to power off %s: %d.\n",
+				phy->dev->name, ret);
+			return ret;
+		}
  	}
  	counts->power_on_count = 0;
 
Reviewed-by on v5 1/6
#12 lore raw
In reply to Eugen Hristev
Quoted 5 lines · Eugen Hristev

Add USB 2.0 host nodes and PHYs.

Thanks,
- Kever

Quoted 222 lines

---
Changes in v5:
- none

Changes in v4:
- removed u-boot,dm-spl on regulator which was useless
- moved usb nodes to rk3588s-u-boot-dtsi

Changes in v2,v3:
- none

  arch/arm/dts/rk3588-rock-5b-u-boot.dtsi | 82 +++++++++++++++++++++++
  arch/arm/dts/rk3588s-u-boot.dtsi        | 86 +++++++++++++++++++++++++
  2 files changed, 168 insertions(+)
arch/arm/dts/rk3588-rock-5b-u-boot.dtsi +82 -0
index bee4c32e8965..93942b105c3d 100644
@@ -4,6 +4,9 @@
   */
 
  #include "rk3588-u-boot.dtsi"
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
 
  / {
  	aliases {
@@ -13,6 +16,18 @@
  	chosen {
  		u-boot,spl-boot-order = &sdmmc;
  	};
+
+	vcc5v0_host: vcc5v0-host-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_host";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&gpio4 RK_PB0 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_host_en>;
+		vin-supply = <&vcc5v0_sys>;
+	};
  };
 
  &sdmmc {
@@ -20,3 +35,70 @@
  	bootph-pre-ram;
  	status = "okay";
  };
+
+&pinctrl {
+	usb {
+		vcc5v0_host_en: vcc5v0-host-en {
+			rockchip,pins = <4 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&usb_host0_ehci {
+	companion = <&usb_host0_ohci>;
+	phys = <&u2phy2_host>;
+	phy-names = "usb2-phy";
+	status = "okay";
+};
+
+&usb_host0_ohci {
+	phys = <&u2phy2_host>;
+	phy-names = "usb2-phy";
+	status = "okay";
+};
+
+&usb2phy2_grf {
+	status = "okay";
+};
+
+&u2phy2 {
+	resets = <&cru SRST_OTGPHY_U2_0>, <&cru SRST_P_USB2PHY_U2_0_GRF0>;
+	reset-names = "phy", "apb";
+	clock-output-names = "usb480m_phy2";
+	status = "okay";
+};
+
+&u2phy2_host {
+	phy-supply = <&vcc5v0_host>;
+	status = "okay";
+};
+
+&usb_host1_ehci {
+	companion = <&usb_host1_ohci>;
+	phys = <&u2phy3_host>;
+	phy-names = "usb2-phy";
+	status = "okay";
+};
+
+&usb_host1_ohci {
+	phys = <&u2phy3_host>;
+	phy-names = "usb2-phy";
+	status = "okay";
+};
+
+&usb2phy3_grf {
+	status = "okay";
+};
+
+&u2phy3 {
+	resets = <&cru SRST_OTGPHY_U2_1>, <&cru SRST_P_USB2PHY_U2_1_GRF0>;
+	reset-names = "phy", "apb";
+	clock-output-names = "usb480m_phy3";
+	status = "okay";
+};
+
+&u2phy3_host {
+	phy-supply = <&vcc5v0_host>;
+	status = "okay";
+};
+
arch/arm/dts/rk3588s-u-boot.dtsi +86 -0
index 1e225d71efc2..fb1b802fd273 100644
@@ -12,12 +12,98 @@
  		status = "okay";
  	};
 
+	usb_host0_ehci: usb@fc800000 {
+		compatible = "generic-ehci";
+		reg = <0x0 0xfc800000 0x0 0x40000>;
+		interrupts = <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH 0>;
+		clocks = <&cru HCLK_HOST0>, <&cru HCLK_HOST_ARB0>;
+		clock-names = "usbhost", "arbiter";
+		power-domains = <&power RK3588_PD_USB>;
+		status = "disabled";
+	};
+
+	usb_host0_ohci: usb@fc840000 {
+		compatible = "generic-ohci";
+		reg = <0x0 0xfc840000 0x0 0x40000>;
+		interrupts = <GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH 0>;
+		clocks = <&cru HCLK_HOST0>, <&cru HCLK_HOST_ARB0>;
+		clock-names = "usbhost", "arbiter";
+		power-domains = <&power RK3588_PD_USB>;
+		status = "disabled";
+	};
+
+	usb_host1_ehci: usb@fc880000 {
+		compatible = "generic-ehci";
+		reg = <0x0 0xfc880000 0x0 0x40000>;
+		interrupts = <GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH 0>;
+		clocks = <&cru HCLK_HOST1>, <&cru HCLK_HOST_ARB1>;
+		clock-names = "usbhost", "arbiter";
+		power-domains = <&power RK3588_PD_USB>;
+		status = "disabled";
+	};
+
+	usb_host1_ohci: usb@fc8c0000 {
+		compatible = "generic-ohci";
+		reg = <0x0 0xfc8c0000 0x0 0x40000>;
+		interrupts = <GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH 0>;
+		clocks = <&cru HCLK_HOST1>, <&cru HCLK_HOST_ARB1>;
+		clock-names = "usbhost", "arbiter";
+		power-domains = <&power RK3588_PD_USB>;
+		status = "disabled";
+	};
+
  	pmu1_grf: syscon@fd58a000 {
  		bootph-all;
  		compatible = "rockchip,rk3588-pmu1-grf", "syscon";
  		reg = <0x0 0xfd58a000 0x0 0x2000>;
  	};
 
+	usb2phy2_grf: syscon@fd5d8000 {
+		compatible = "rockchip,rk3588-usb2phy-grf", "syscon",
+			     "simple-mfd";
+		reg = <0x0 0xfd5d8000 0x0 0x4000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		u2phy2: usb2-phy@8000 {
+			compatible = "rockchip,rk3588-usb2phy";
+			reg = <0x8000 0x10>;
+			interrupts = <GIC_SPI 391 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&cru CLK_USB2PHY_HDPTXRXPHY_REF>;
+			clock-names = "phyclk";
+			#clock-cells = <0>;
+			status = "disabled";
+
+			u2phy2_host: host-port {
+				#phy-cells = <0>;
+				status = "disabled";
+			};
+		};
+	};
+
+	usb2phy3_grf: syscon@fd5dc000 {
+		compatible = "rockchip,rk3588-usb2phy-grf", "syscon",
+			     "simple-mfd";
+		reg = <0x0 0xfd5dc000 0x0 0x4000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		u2phy3: usb2-phy@c000 {
+			compatible = "rockchip,rk3588-usb2phy";
+			reg = <0xc000 0x10>;
+			interrupts = <GIC_SPI 392 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&cru CLK_USB2PHY_HDPTXRXPHY_REF>;
+			clock-names = "phyclk";
+			#clock-cells = <0>;
+			status = "disabled";
+
+			u2phy3_host: host-port {
+				#phy-cells = <0>;
+				status = "disabled";
+			};
+		};
+	};
+
  	sdmmc: mmc@fe2c0000 {
  		compatible = "rockchip,rk3588-dw-mshc", "rockchip,rk3288-dw-mshc";
  		reg = <0x0 0xfe2c0000 0x0 0x4000>;
#13 lore raw
In reply to Eugen Hristev

Hi Eugen,

    When I try to apply this patch, I got conflict for rk3588-rock-5b-u-boot.dtsi, could you please help to send a rebase?

Thanks,

- Kever

Quoted 227 lines · Eugen Hristev

Add USB 2.0 host nodes and PHYs.

---
Changes in v5:
- none

Changes in v4:
- removed u-boot,dm-spl on regulator which was useless
- moved usb nodes to rk3588s-u-boot-dtsi

Changes in v2,v3:
- none

  arch/arm/dts/rk3588-rock-5b-u-boot.dtsi | 82 +++++++++++++++++++++++
  arch/arm/dts/rk3588s-u-boot.dtsi        | 86 +++++++++++++++++++++++++
  2 files changed, 168 insertions(+)
arch/arm/dts/rk3588-rock-5b-u-boot.dtsi +82 -0
index bee4c32e8965..93942b105c3d 100644
@@ -4,6 +4,9 @@
   */
 
  #include "rk3588-u-boot.dtsi"
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
 
  / {
  	aliases {
@@ -13,6 +16,18 @@
  	chosen {
  		u-boot,spl-boot-order = &sdmmc;
  	};
+
+	vcc5v0_host: vcc5v0-host-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_host";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&gpio4 RK_PB0 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_host_en>;
+		vin-supply = <&vcc5v0_sys>;
+	};
  };
 
  &sdmmc {
@@ -20,3 +35,70 @@
  	bootph-pre-ram;
  	status = "okay";
  };
+
+&pinctrl {
+	usb {
+		vcc5v0_host_en: vcc5v0-host-en {
+			rockchip,pins = <4 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&usb_host0_ehci {
+	companion = <&usb_host0_ohci>;
+	phys = <&u2phy2_host>;
+	phy-names = "usb2-phy";
+	status = "okay";
+};
+
+&usb_host0_ohci {
+	phys = <&u2phy2_host>;
+	phy-names = "usb2-phy";
+	status = "okay";
+};
+
+&usb2phy2_grf {
+	status = "okay";
+};
+
+&u2phy2 {
+	resets = <&cru SRST_OTGPHY_U2_0>, <&cru SRST_P_USB2PHY_U2_0_GRF0>;
+	reset-names = "phy", "apb";
+	clock-output-names = "usb480m_phy2";
+	status = "okay";
+};
+
+&u2phy2_host {
+	phy-supply = <&vcc5v0_host>;
+	status = "okay";
+};
+
+&usb_host1_ehci {
+	companion = <&usb_host1_ohci>;
+	phys = <&u2phy3_host>;
+	phy-names = "usb2-phy";
+	status = "okay";
+};
+
+&usb_host1_ohci {
+	phys = <&u2phy3_host>;
+	phy-names = "usb2-phy";
+	status = "okay";
+};
+
+&usb2phy3_grf {
+	status = "okay";
+};
+
+&u2phy3 {
+	resets = <&cru SRST_OTGPHY_U2_1>, <&cru SRST_P_USB2PHY_U2_1_GRF0>;
+	reset-names = "phy", "apb";
+	clock-output-names = "usb480m_phy3";
+	status = "okay";
+};
+
+&u2phy3_host {
+	phy-supply = <&vcc5v0_host>;
+	status = "okay";
+};
+
arch/arm/dts/rk3588s-u-boot.dtsi +86 -0
index 1e225d71efc2..fb1b802fd273 100644
@@ -12,12 +12,98 @@
  		status = "okay";
  	};
 
+	usb_host0_ehci: usb@fc800000 {
+		compatible = "generic-ehci";
+		reg = <0x0 0xfc800000 0x0 0x40000>;
+		interrupts = <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH 0>;
+		clocks = <&cru HCLK_HOST0>, <&cru HCLK_HOST_ARB0>;
+		clock-names = "usbhost", "arbiter";
+		power-domains = <&power RK3588_PD_USB>;
+		status = "disabled";
+	};
+
+	usb_host0_ohci: usb@fc840000 {
+		compatible = "generic-ohci";
+		reg = <0x0 0xfc840000 0x0 0x40000>;
+		interrupts = <GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH 0>;
+		clocks = <&cru HCLK_HOST0>, <&cru HCLK_HOST_ARB0>;
+		clock-names = "usbhost", "arbiter";
+		power-domains = <&power RK3588_PD_USB>;
+		status = "disabled";
+	};
+
+	usb_host1_ehci: usb@fc880000 {
+		compatible = "generic-ehci";
+		reg = <0x0 0xfc880000 0x0 0x40000>;
+		interrupts = <GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH 0>;
+		clocks = <&cru HCLK_HOST1>, <&cru HCLK_HOST_ARB1>;
+		clock-names = "usbhost", "arbiter";
+		power-domains = <&power RK3588_PD_USB>;
+		status = "disabled";
+	};
+
+	usb_host1_ohci: usb@fc8c0000 {
+		compatible = "generic-ohci";
+		reg = <0x0 0xfc8c0000 0x0 0x40000>;
+		interrupts = <GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH 0>;
+		clocks = <&cru HCLK_HOST1>, <&cru HCLK_HOST_ARB1>;
+		clock-names = "usbhost", "arbiter";
+		power-domains = <&power RK3588_PD_USB>;
+		status = "disabled";
+	};
+
  	pmu1_grf: syscon@fd58a000 {
  		bootph-all;
  		compatible = "rockchip,rk3588-pmu1-grf", "syscon";
  		reg = <0x0 0xfd58a000 0x0 0x2000>;
  	};
 
+	usb2phy2_grf: syscon@fd5d8000 {
+		compatible = "rockchip,rk3588-usb2phy-grf", "syscon",
+			     "simple-mfd";
+		reg = <0x0 0xfd5d8000 0x0 0x4000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		u2phy2: usb2-phy@8000 {
+			compatible = "rockchip,rk3588-usb2phy";
+			reg = <0x8000 0x10>;
+			interrupts = <GIC_SPI 391 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&cru CLK_USB2PHY_HDPTXRXPHY_REF>;
+			clock-names = "phyclk";
+			#clock-cells = <0>;
+			status = "disabled";
+
+			u2phy2_host: host-port {
+				#phy-cells = <0>;
+				status = "disabled";
+			};
+		};
+	};
+
+	usb2phy3_grf: syscon@fd5dc000 {
+		compatible = "rockchip,rk3588-usb2phy-grf", "syscon",
+			     "simple-mfd";
+		reg = <0x0 0xfd5dc000 0x0 0x4000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		u2phy3: usb2-phy@c000 {
+			compatible = "rockchip,rk3588-usb2phy";
+			reg = <0xc000 0x10>;
+			interrupts = <GIC_SPI 392 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&cru CLK_USB2PHY_HDPTXRXPHY_REF>;
+			clock-names = "phyclk";
+			#clock-cells = <0>;
+			status = "disabled";
+
+			u2phy3_host: host-port {
+				#phy-cells = <0>;
+				status = "disabled";
+			};
+		};
+	};
+
  	sdmmc: mmc@fe2c0000 {
  		compatible = "rockchip,rk3588-dw-mshc", "rockchip,rk3288-dw-mshc";
  		reg = <0x0 0xfe2c0000 0x0 0x4000>;