Add support for cyclic function execution infrastruture
v2 cover Add support for cyclic function execution infrastruture
This patchset adds the basic infrastructure to periodically execute code, e.g. all 100ms. Examples for such functions might be LED blinking etc. The functions that are hooked into this cyclic list should be small timewise as otherwise the execution of the other code that relies on a high frequent polling (e.g. UART rx char ready check) might be delayed too much. This patch also adds the Kconfig option CONFIG_CYCLIC_MAX_CPU_TIME_US, which configures the max allowed time for such a cyclic function. If it's execution time exceeds this time, this cyclic function will get removed from the cyclic list.
How is this cyclic functionality executed?
This patchset integrates the main function responsible for calling all registered cyclic functions cyclic_run() into the common WATCHDOG_RESET macro. This guarantees that cyclic_run() is executed very often, which is necessary for the cyclic functions to get scheduled and executed at their configured periods.
This cyclic infrastructure will be used by a board specific function on the NIC23 MIPS Octeon board, which needs to check periodically, if a PCIe FLR has occurred.
Ideas how to continue:
One idea is to rename WATCHDOG_RESET to something like SCHEDULE and move the watchdog_reset call into this cyclic infrastructure as well. Or to perhaps move the shell UART RX ready polling to a cyclic function.
It's also possible to extend the "cyclic" command, to support the creation of periodically executed shell commands (for testing etc).
Here the Azure build, without any issues:
https://dev.azure.com/sr0718/u-boot/_build/results?buildId=219&view=results
Thanks,
Stefan
Aaron Williams (1):
mips: octeon_nic23: Add PCIe FLR fixup via cyclic infrastructure
Stefan Roese (6):
time: Import time_after64() and friends from Linux
cyclic: Add basic support for cyclic function execution infrastruture
cyclic: Integrate cyclic infrastructure into WATCHDOG_RESET
cyclic: Integrate cyclic functionality at bootup in board_r/f
cyclic: Add 'cyclic list' command
sandbox: Add cyclic demo function
MAINTAINERS | 7 + board/Marvell/octeon_nic23/board.c | 197 +++++++++++++++++++++++++++++ board/sandbox/sandbox.c | 15 +++ cmd/Kconfig | 7 + cmd/Makefile | 1 + cmd/cyclic.c | 40 ++++++ common/Kconfig | 20 +++ common/Makefile | 1 + common/board_f.c | 2 + common/board_r.c | 2 + common/cyclic.c | 112 ++++++++++++++++ configs/octeon_nic23_defconfig | 3 + configs/sandbox_defconfig | 3 + fs/cramfs/uncompress.c | 2 +- include/cyclic.h | 97 ++++++++++++++ include/time.h | 19 +++ include/watchdog.h | 23 +++- 17 files changed, 547 insertions(+), 4 deletions(-) create mode 100644 cmd/cyclic.c create mode 100644 common/cyclic.c create mode 100644 include/cyclic.h
Signature · 1 line
2.37.1
PATCH v2 1/7 time: Import time_after64() and friends from Linux
When using us times it makes sense to use 64bit variables for storage. The currently implemented time_after() and friends functions only handle 32bit variables. This patch now includes the 64bit variants as well from Linux. This will be used by the upcoming generic cyclic function infrastructure.
These macros were copied from include/linux/jiffies.h of Linux 5.18.
---
v2:
- No change
include/time.h | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+)
include/time.h +19 -0
@@ -83,6 +83,25 @@ uint64_t usec_to_tick(unsigned long usec); (time_after_eq (a,b) && \time_before (a,c)) +/* Same as above, but does so with platform independent 64bit types. +* These must be used when utilizing jiffies_64 (i.e. return value of + * get_jiffies_64() */ +#define time_after64 (a,b) \ + (typecheck(__u64, a) && \ + typecheck(__u64, b) && \ + ((__s64)((b) - (a)) < 0)) +#define time_before64 (a,b) time_after64(b,a) + +#define time_after_eq64 (a,b) \ + (typecheck(__u64, a) && \ + typecheck(__u64, b) && \ + ((__s64)((a) - (b)) >= 0)) +#define time_before_eq64 (a,b) time_after_eq64(b,a) + +#define time_in_range64 (a, b, c) \ + (time_after_eq64(a, b) && \ + time_before_eq64(a, c)) +/** * usec2ticks() - Convert microseconds to internal ticks *
Signature · 1 line
2.37.1
PATCH v2 2/7 cyclic: Add basic support for cyclic function execution infrastruture
In reply to Stefan RoeseAdd the basic infrastructure to periodically execute code, e.g. all 100ms. Examples for such functions might be LED blinking etc. The functions that are hooked into this cyclic list should be small timewise as otherwise the execution of the other code that relies on a high frequent polling (e.g. UART rx char ready check) might be delayed too much. This patch also adds the Kconfig option CONFIG_CYCLIC_MAX_CPU_TIME_US, which configures the max allowed time for such a cyclic function. If it's execution time exceeds this time, this cyclic function will get removed from the cyclic list.
How is this cyclic functionality executed?
The following patch integrates the main function responsible for calling all registered cyclic functions cyclic_run() into the common WATCHDOG_RESET macro. This guarantees that cyclic_run() is executed very often, which is necessary for the cyclic functions to get scheduled and executed at their configured periods.
This cyclic infrastructure will be used by a board specific function on the NIC23 MIPS Octeon board, which needs to check periodically, if a PCIe FLR has occurred.
---
v2:
- Also add cyclic_register() and cyclic_unregister() as empty functions when CONFIG_CYCLIC is not defined
- Misc minor changes
MAINTAINERS | 6 +++ common/Kconfig | 20 +++++++++ common/Makefile | 1 + common/cyclic.c | 112 +++++++++++++++++++++++++++++++++++++++++++++++ include/cyclic.h | 97 ++++++++++++++++++++++++++++++++++++++++ 5 files changed, 236 insertions(+) create mode 100644 common/cyclic.c create mode 100644 include/cyclic.h
MAINTAINERS +6 -0
@@ -788,6 +788,12 @@ T: git https://source.denx.de/u-boot/custodians/u-boot-coldfire.git F: arch/m68k/ F: doc/arch/m68k.rst +CYCLIC +M: Stefan Roese <[email protected]> +S: Maintained +F: common/cyclic.c +F: include/cyclic.h + DFU M: Lukasz Majewski <[email protected]> S: Maintained
common/Kconfig +20 -0
@@ -545,6 +545,26 @@ config DISPLAY_BOARDINFO_LATE menu "Start-up hooks" +config CYCLIC + bool "General-purpose cyclic execution mechanism" + help + This enables a general-purpose cyclic execution infrastructure, + to allow "small" (run-time wise) functions to be executed at + a specified frequency. Things like LED blinking or watchdog + triggering are examples for such tasks. + +if CYCLIC + +config CYCLIC_MAX_CPU_TIME_US + int "Sets the max allowed time for a cyclic function in us" + default 1000 + help + The max allowed time for a cyclic function in us. If a functions + takes longer than this duration this function will get unregistered + automatically. + +endif # CYCLIC + config EVENT bool "General-purpose event-handling mechanism" default y if SANDBOX
common/Makefile +1 -0
@@ -84,6 +84,7 @@ obj-y += malloc_simple.o endif endif +obj-$(CONFIG_CYCLIC) += cyclic.o obj-$(CONFIG_$(SPL_TPL_)EVENT) += event.o obj-$(CONFIG_$(SPL_TPL_)HASH) += hash.o
common/cyclic.c new file +112 -0
112 lines not on this page · raw message
include/cyclic.h new file +97 -0
97 lines not on this page · raw message
Signature · 1 line
2.37.1
PATCH v2 3/7 cyclic: Integrate cyclic infrastructure into WATCHDOG_RESET
In reply to Stefan RoeseThis patch integrates the main function responsible for calling all registered cyclic functions cyclic_run() into the common WATCHDOG_RESET macro. This guarantees that cyclic_run() is executed very often, which is necessary for the cyclic functions to get scheduled and executed at their configured periods.
If CONFIG_WATCHDOG is not enabled, only cyclic_run() without calling watchdog_reset(). This guarantees that the cyclic functionality does not rely on CONFIG_WATCHDOG being enabled.
---
v2:
- No change
fs/cramfs/uncompress.c | 2 +- include/watchdog.h | 23 ++++++++++++++++++++--- 2 files changed, 21 insertions(+), 4 deletions(-)
fs/cramfs/uncompress.c +1 -1
@@ -62,7 +62,7 @@ int cramfs_uncompress_init (void) stream.avail_in =0 ;#if defined(CONFIG_HW_WATCHDOG ) || defined(CONFIG_WATCHDOG ) - stream.outcb = (cb_func )WATCHDOG_RESET ; + stream.outcb = (cb_func )watchdog_reset_func;#else stream.outcb =Z_NULL ;#endif /* CONFIG_HW_WATCHDOG */
include/watchdog.h +20 -3
@@ -11,6 +11,8 @@#define _WATCHDOG_H_#if !defined(__ASSEMBLY__) +#include <cyclic.h> +/* * Reset the watchdog timer, always returns 0 *
@@ -60,11 +62,16 @@ int init_func_watchdog_reset(void);/* Don't require the watchdog to be enabled in SPL */ #if defined(CONFIG_SPL_BUILD ) && \ !defined(CONFIG_SPL_WATCHDOG ) -#define WATCHDOG_RESET () {} +#define WATCHDOG_RESET () { \ + cyclic_run(); \ + }#else extern void watchdog_reset (void ); -#define WATCHDOG_RESET watchdog_reset +#define WATCHDOG_RESET () { \ + watchdog_reset(); \ + cyclic_run(); \ + }#endif #endif #else
@@ -74,11 +81,21 @@ int init_func_watchdog_reset(void);#if defined(__ASSEMBLY__)#define WATCHDOG_RESET /*XXX DO_NOT_DEL_THIS_COMMENT*/ #else -#define WATCHDOG_RESET () {} +#define WATCHDOG_RESET () { \ + cyclic_run(); \ + }#endif /* __ASSEMBLY__ */ #endif /* CONFIG_WATCHDOG && !__ASSEMBLY__ */ #endif /* CONFIG_HW_WATCHDOG */ +#if !defined(__ASSEMBLY__) +/* Currently only needed for fs/cramfs/uncompress.c */ +static inline void watchdog_reset_func (void ) +{ +WATCHDOG_RESET (); +} +#endif +/* * Prototypes from $(CPU)/cpu.c. */
Signature · 1 line
2.37.1
PATCH v2 4/7 cyclic: Integrate cyclic functionality at bootup in board_r/f
In reply to Stefan RoeseThis patch adds a call to cyclic_init() to board_f/r.c, enabling the common cyclic infrastructure. After this it's possible to add cyclic functions via cyclic_register().
---
v2:
- No change
common/board_f.c | 2 ++ common/board_r.c | 2 ++ 2 files changed, 4 insertions(+)
common/board_f.c +2 -0
@@ -16,6 +16,7 @@#include <console.h> #include <cpu.h> #include <cpu_func.h> +#include <cyclic.h> #include <dm.h> #include <env.h> #include <env_internal.h>
@@ -827,6 +828,7 @@ static const init_fnc_t init_sequence_f[] = { initf_malloc, log_init, initf_bootstage,/* uses its own timer, so does not need DM */ + cyclic_init, event_init, #ifdef CONFIG_BLOBLIST bloblist_init,
common/board_r.c +2 -0
@@ -13,6 +13,7 @@#include <api.h> #include <bootstage.h> #include <cpu_func.h> +#include <cyclic.h> #include <exports.h> #include <flash.h> #include <hang.h>
@@ -588,6 +589,7 @@ static int run_main_loop(void)static init_fnc_t init_sequence_r[] = { initr_trace, initr_reloc, + cyclic_init, event_init,/* TODO: could x86/PPC have this also perhaps? */ #if defined(CONFIG_ARM) || defined(CONFIG_RISCV)
Signature · 1 line
2.37.1
PATCH v2 5/7 cyclic: Add 'cyclic list' command
In reply to Stefan RoeseThis patch adds the cyclic command, which currently only supports the 'list' subcommand, to list all currently registered cyclic functions. Here an example:
=> cyclic list
function: cyclic_demo, cpu-time: 7010 us, frequency: 99.80 times/s
function: cyclic_demo2, cpu-time: 1 us, frequency: 1.13 times/s
As you can see, the cpu-time is accounted, so that cyclic functions that take too long might be discovered. Additionally the frequency is logged.
---
v2:
- Add depends on CYCLIC in Kconfig
MAINTAINERS | 1 + cmd/Kconfig | 7 +++++++ cmd/Makefile | 1 + cmd/cyclic.c | 40 ++++++++++++++++++++++++++++++++++++++++ 4 files changed, 49 insertions(+) create mode 100644 cmd/cyclic.c
MAINTAINERS +1 -0
@@ -791,6 +791,7 @@ F: doc/arch/m68k.rst CYCLIC M: Stefan Roese <[email protected]> S: Maintained +F: cmd/cyclic.c F: common/cyclic.c F: include/cyclic.h
cmd/Kconfig +7 -0
@@ -2494,6 +2494,13 @@ config CMD_CBSYSINFO memory by coreboot before jumping to U-Boot. It can be useful for debugging the beaaviour of coreboot or U-Boot. +config CMD_CYCLIC + bool "cyclic - Show information about cyclic functions" + depends on CYCLIC + help + This enables the 'cyclic' command which provides information about + cyclic excution functions. + config CMD_DIAG bool "diag - Board diagnostics" help
cmd/Makefile +1 -0
@@ -56,6 +56,7 @@ obj-$(CONFIG_CMD_DIAG) += diag.o endif obj-$(CONFIG_CMD_ADTIMG) += adtimg.o obj-$(CONFIG_CMD_ABOOTIMG) += abootimg.o +obj-$(CONFIG_CMD_CYCLIC) += cyclic.o obj-$(CONFIG_CMD_EVENT) += event.o obj-$(CONFIG_CMD_EXTENSION) += extension_board.o obj-$(CONFIG_CMD_ECHO) += echo.o
cmd/cyclic.c new file +40 -0
@@ -0,0 +1,40 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* A general-purpose cyclic execution infrastructure, to allow "small" +* (run-time wise) functions to be executed at a specified frequency. +* Things like LED blinking or watchdog triggering are examples for such +* tasks. +* +* Copyright (C) 2022 Stefan Roese <[email protected]> +*/ + +#include <common.h> +#include <command.h> +#include <cyclic.h> + +extern struct list_head cyclic_list; + +static int do_cyclic_list (struct cmd_tbl *cmdtp,int flag,int argc, +char *const argv[]) +{ +struct cyclic_struct *cyclic, *tmp; +uint64_t cnt, freq; + +list_for_each_entry_safe (cyclic, tmp, &cyclic_list, list) { + cnt = cyclic->run_cnt *1000000ULL *100ULL ; + freq = cnt / (timer_get_us () - cyclic->start_time_us); +printf ("function: %s, cpu-time: %lld us, frequency: %lld.%02lld times/s\n" , + cyclic->name, cyclic->cpu_time_us, + freq /100 , freq %100 ); + } + +return 0 ; +} + +#ifdef CONFIG_SYS_LONGHELP +static char cyclic_help_text[] = +"cyclic list - list cyclic functions" ; +#endif + +U_BOOT_CMD_WITH_SUBCMDS (cyclic,"Cyclic" , cyclic_help_text, +U_BOOT_SUBCMD_MKENT (list,1 ,1 , do_cyclic_list));
Signature · 1 line
2.37.1
PATCH v2 6/7 sandbox: Add cyclic demo function
In reply to Stefan RoeseThis patch enables the cyclic infrastructure on sandbox and also adds one simple example/demo functions using this cyclic functionality.
---
v2:
- Extend CONFIG_CYCLIC_MAX_CPU_TIME_US to 10000ms as running this in CI might take a bit longer
board/sandbox/sandbox.c | 15 +++++++++++++++ configs/sandbox_defconfig | 3 +++ 2 files changed, 18 insertions(+)
board/sandbox/sandbox.c +15 -0
@@ -7,6 +7,7 @@#include <addr_map.h> #include <cpu_func.h> #include <cros_ec.h> +#include <cyclic.h> #include <dm.h> #include <efi.h> #include <efi_loader.h>
@@ -17,6 +18,7 @@#include <asm/global_data.h> #include <asm/test.h> #include <asm/u-boot-sandbox.h> +#include <linux/delay.h> #include <linux/kernel.h> #include <malloc.h>
@@ -106,8 +108,21 @@ int dram_init(void)return 0 ; } +static void cyclic_demo (void *ctx) +{ +/* Just a small dummy delay here */ +udelay (10 ); +} +int board_init (void ) { +struct cyclic_struct *cyclic; + +/* Register demo cyclic function */ + cyclic =cyclic_register (cyclic_demo,10 *1000 ,"cyclic_demo" ,NULL ); +if (!cyclic) +printf ("Registering of cyclic_demo failed\n" ); +return 0 ; }
configs/sandbox_defconfig +3 -0
@@ -34,6 +34,8 @@ CONFIG_LOG=y CONFIG_LOG_MAX_LEVEL=9 CONFIG_LOG_DEFAULT_LEVEL=6 CONFIG_DISPLAY_BOARDINFO_LATE=y +CONFIG_CYCLIC=y +CONFIG_CYCLIC_MAX_CPU_TIME_US=10000 CONFIG_STACKPROTECTOR=y CONFIG_ANDROID_AB=y CONFIG_CMD_CPU=y
@@ -114,6 +116,7 @@ CONFIG_CMD_EROFS=y CONFIG_CMD_EXT4_WRITE=y CONFIG_CMD_SQUASHFS=y CONFIG_CMD_MTDPARTS=y +CONFIG_CMD_CYCLIC=y CONFIG_CMD_STACKPROTECTOR_TEST=y CONFIG_MAC_PARTITION=y CONFIG_AMIGA_PARTITION=y
Signature · 1 line
2.37.1
PATCH v2 7/7 mips: octeon_nic23: Add PCIe FLR fixup via cyclic infrastructure
In reply to Stefan RoeseFrom: Aaron Williams <[email protected]>
This patch adds a fixup function related to a PCIe FLR (Function Level Reset) problem on the NIC23 PCIe board. This function is imported from the Marvell Octeon 2013 U-Boot version as a (nearly) verbatim copy. It uses the newly introduced cyclic infrastructure, so that this function gets called every 100us, which is needed to detect this FLR issue.
---
v2:
- No change
board/Marvell/octeon_nic23/board.c | 197 +++++++++++++++++++++++++++++ configs/octeon_nic23_defconfig | 3 + 2 files changed, 200 insertions(+)
board/Marvell/octeon_nic23/board.c +197 -0
@@ -3,8 +3,10 @@* Copyright (C) 2021-2022 Stefan Roese <[email protected]> */ +#include <cyclic.h> #include <dm.h> #include <ram.h> +#include <time.h> #include <asm/gpio.h> #include <mach/octeon_ddr.h>
@@ -15,11 +17,90 @@#include <mach/cvmx-helper-cfg.h> #include <mach/cvmx-helper-util.h> #include <mach/cvmx-bgxx-defs.h> +#include <mach/cvmx-dtx-defs.h> #include "board_ddr.h" +/** +* cvmx_spem#_cfg_rd +* +* This register allows read access to the configuration in the PCIe core. +* +*/ +union cvmx_spemx_cfg_rd { +u64 u64; +struct cvmx_spemx_cfg_rd_s { +u64 data :32 ; +u64 addr :32 ; + } s; +struct cvmx_spemx_cfg_rd_s cn73xx; +}; + +/** +* cvmx_spem#_cfg_wr +* +* This register allows write access to the configuration in the PCIe core. +* +*/ +union cvmx_spemx_cfg_wr { +u64 u64; +struct cvmx_spemx_cfg_wr_s { +u64 data :32 ; +u64 addr :32 ; + } s; +struct cvmx_spemx_cfg_wr_s cn73xx; +}; + +/** +* cvmx_spem#_flr_pf_stopreq +* +* PF function level reset stop outbound requests register. +* Hardware automatically sets the STOPREQ bit for the PF when it enters a +* function level reset (FLR). Software is responsible for clearing the STOPREQ +* bit but must not do so prior to hardware taking down the FLR, which could be +* as long as 100ms. It may be appropriate for software to wait longer before clearing +* STOPREQ, software may need to drain deep DPI queues for example. +* Whenever SPEM receives a PF or child VF request mastered by CNXXXX over S2M (i.e. P or NP), +* when STOPREQ is set for the function, SPEM will discard the outgoing request +* before sending it to the PCIe core. If a NP, SPEM will schedule an immediate +* SWI_RSP_ERROR completion for the request - no timeout is required. +* In both cases, SPEM()_DBG_PF()_INFO[P()_BMD_E] will be set and a error +* interrupt is generated. +* +* STOPREQ mimics the behavior of PCIEEP()_CFG001[ME] for outbound requests that will +* master the PCIe bus (P and NP). +* +* STOPREQ will have no effect on completions returned by CNXXXX over the S2M, +* nor on M2S traffic. +* +* When a PF()_STOPREQ is set, none of the associated +* PEM()_FLR_PF()_VF_STOPREQ[VF_STOPREQ] will be set. +* +* STOPREQ is reset when the MAC is reset, and is not reset after a chip soft reset. +*/ +union cvmx_spemx_flr_pf_stopreq { +u64 u64; +struct cvmx_spemx_flr_pf_stopreq_s { +u64 reserved_3_63 :61 ; +u64 pf2_stopreq :1 ; +u64 pf1_stopreq :1 ; +u64 pf0_stopreq :1 ; + } s; +struct cvmx_spemx_flr_pf_stopreq_s cn73xx; +}; + +#define CVMX_SPEMX_CFG_WR (offset) 0x00011800C0000028ull +#define CVMX_SPEMX_CFG_RD (offset) 0x00011800C0000030ull +#define CVMX_SPEMX_FLR_PF_STOPREQ (offset) 0x00011800C0000218ull + +#define DTX_SELECT_LTSSM 0x0 +#define DTX_SELECT_LTSSM_ENA 0x3ff +#define LTSSM_L0 0x11 +#define NIC23_DEF_DRAM_FREQ 800 +static u32 pci_cfgspace_reg0[2 ] = {0 ,0 }; +static u8 octeon_nic23_cfg0_spd_values[512 ] = {OCTEON_NIC23_CFG0_SPD_VALUES };
@@ -145,8 +226,118 @@ void board_configure_qlms(void) cvmx_qlm_measure_clock(4), cvmx_qlm_measure_clock(5)); } +/** +* If there is a PF FLR then the PCI EEPROM is not re-read. In this case +* we need to re-program the vendor and device ID immediately after hardware +* completes FLR. +* +* PCI spec requires FLR to be completed within 100ms. The user who triggered +* FLR expects hardware to finish FLR within 100ms, otherwise the user will +* end up reading DEVICE_ID incorrectly from the reset value. +* CN23XX exits FLR at any point between 66 and 99ms, so U-Boot has to wait +* 99ms to let hardware finish its part, then finish reprogramming the +* correct device ID before the end of 100ms. +* +* Note: this solution only works properly when there is no other activity +* within U-Boot for 100ms from the time FLR is triggered. +* +* This function gets called every 100usec. If FLR happens during any +* other activity like bootloader/image update then it is possible that +* this function does not get called for more than the FLR period which will +* cause the PF device ID restore to happen after whoever initiated the FLR to +* read the incorrect device ID 0x9700 (reset value) instead of 0x9702 +* (restored value). +*/ +static void octeon_board_restore_pf (void *ctx) +{ +union cvmx_spemx_flr_pf_stopreq stopreq; +static bool start_initialized[2 ] = {false, false}; +bool pf0_flag, pf1_flag; +u64 ltssm_bits; +const u64 pf_flr_wait_usecs =99700 ; +u64 elapsed_usecs; +union cvmx_spemx_cfg_wr cfg_wr; +union cvmx_spemx_cfg_rd cfg_rd; +static u64 start_us[2 ]; +int pf_num; + +csr_wr (CVMX_DTX_SPEM_SELX (0 ),DTX_SELECT_LTSSM ); +csr_rd (CVMX_DTX_SPEM_SELX (0 )); +csr_wr (CVMX_DTX_SPEM_ENAX (0 ),DTX_SELECT_LTSSM_ENA ); +csr_rd (CVMX_DTX_SPEM_ENAX (0 )); + ltssm_bits =csr_rd (CVMX_DTX_SPEM_DATX (0 )); +if (((ltssm_bits >>3 ) &0x3f ) !=LTSSM_L0 ) +return ; + + stopreq.u64 =csr_rd (CVMX_SPEMX_FLR_PF_STOPREQ (0 )); + pf0_flag = stopreq.s.pf0_stopreq; + pf1_flag = stopreq.s.pf1_stopreq; +/* See if PF interrupt happened */ +if (!(pf0_flag || pf1_flag)) +return ; + +if (pf0_flag && !start_initialized[0 ]) { + start_initialized[0 ] = true; + start_us[0 ] =get_timer_us (0 ); + } + +/* Store programmed PCIe DevID SPEM0 PF0 */ +if (pf0_flag && !pci_cfgspace_reg0[0 ]) { + cfg_rd.s.addr = (0 <<24 ) |0x0 ; +csr_wr (CVMX_SPEMX_CFG_RD (0 ), cfg_rd.u64); + cfg_rd.u64 =csr_rd (CVMX_SPEMX_CFG_RD (0 )); + pci_cfgspace_reg0[0 ] = cfg_rd.s.data; + } + +if (pf1_flag && !start_initialized[1 ]) { + start_initialized[1 ] = true; + start_us[1 ] =get_timer_us (0 ); + } + +/* Store programmed PCIe DevID SPEM0 PF1 */ +if (pf1_flag && !pci_cfgspace_reg0[1 ]) { + cfg_rd.s.addr = (1 <<24 ) |0x0 ; +csr_wr (CVMX_SPEMX_CFG_RD (0 ), cfg_rd.u64); + cfg_rd.u64 =csr_rd (CVMX_SPEMX_CFG_RD (0 )); + pci_cfgspace_reg0[1 ] = cfg_rd.s.data; + } + +/* For PF, rewrite pci config space reg 0 */ +for (pf_num =0 ; pf_num <2 ; pf_num++) { +if (!start_initialized[pf_num]) +continue ; + + elapsed_usecs =get_timer_us (0 ) - start_us[pf_num]; + +if (elapsed_usecs > pf_flr_wait_usecs) { +/* Here, our measured FLR duration has passed; +* check if device ID has been reset, +* which indicates FLR completion (per MA team). +*/ + cfg_rd.s.addr = (pf_num <<24 ) |0x0 ; +csr_wr (CVMX_SPEMX_CFG_RD (0 ), cfg_rd.u64); + cfg_rd.u64 =csr_rd (CVMX_SPEMX_CFG_RD (0 )); +/* if DevID has NOT been reset, FLR is not yet +* complete +*/ +if (cfg_rd.s.data != pci_cfgspace_reg0[pf_num]) { + stopreq.s.pf0_stopreq = (pf_num ==0 ) ?1 :0 ; + stopreq.s.pf1_stopreq = (pf_num ==1 ) ?1 :0 ; +csr_wr (CVMX_SPEMX_FLR_PF_STOPREQ (0 ), stopreq.u64); + + cfg_wr.u64 =0 ; + cfg_wr.s.addr = (pf_num <<24 ) |0 ; + cfg_wr.s.data = pci_cfgspace_reg0[pf_num]; +csr_wr (CVMX_SPEMX_CFG_WR (0 ), cfg_wr.u64); + start_initialized[pf_num] = false; + } + } + } +} +int board_late_init (void ) { +struct cyclic_struct *cyclic;struct gpio_desc gpio = {};ofnode node;
@@ -164,6 +355,12 @@ int board_late_init(void)board_configure_qlms (); +/* Register cyclic function for PCIe FLR fixup */ + cyclic =cyclic_register (octeon_board_restore_pf,100 , +"pcie_flr_fix" ,NULL ); +if (!cyclic) +printf ("Registering of cyclic function failed\n" ); +return 0 ; }
configs/octeon_nic23_defconfig +3 -0
@@ -20,6 +20,8 @@ CONFIG_AHCI=y CONFIG_OF_BOARD_FIXUP=y CONFIG_SYS_CONSOLE_ENV_OVERWRITE=y # CONFIG_SYS_DEVICE_NULLDEV is not set +CONFIG_CYCLIC=y +CONFIG_CYCLIC_MAX_CPU_TIME_US=5000 CONFIG_ARCH_MISC_INIT=y CONFIG_BOARD_EARLY_INIT_F=y CONFIG_BOARD_LATE_INIT=y
@@ -41,6 +43,7 @@ CONFIG_CMD_TIME=y CONFIG_CMD_EXT4=y CONFIG_CMD_FAT=y CONFIG_CMD_FS_GENERIC=y +CONFIG_CMD_CYCLIC=y CONFIG_EFI_PARTITION=y CONFIG_ENV_IS_IN_SPI_FLASH=y CONFIG_TFTP_TSIZE=y
Signature · 1 line
2.37.1
Hi Stefan,
Quoted 70 lines · Stefan Roese
This patchset adds the basic infrastructure to periodically execute code, e.g. all 100ms. Examples for such functions might be LED blinking etc. The functions that are hooked into this cyclic list should be small timewise as otherwise the execution of the other code that relies on a high frequent polling (e.g. UART rx char ready check) might be delayed too much. This patch also adds the
KconfigoptionCONFIG_CYCLIC_MAX_CPU_TIME_US, which configures the max allowed time for such a cyclic function. If it's execution time exceeds this time, this cyclic function will get removed from the cyclic list.How is this cyclic functionality executed?
This patchset integrates the main function responsible for calling all registered cyclic functionscyclic_run()into the commonWATCHDOG_RESETmacro. This guarantees thatcyclic_run()is executed very often, which is necessary for the cyclic functions to get scheduled and executed at their configured periods.This cyclic infrastructure will be used by a board specific function on the NIC23 MIPS Octeon board, which needs to check periodically, if a PCIe FLR has occurred.
Ideas how to continue:
One idea is to renameWATCHDOG_RESETto something like SCHEDULE and move thewatchdog_resetcall into this cyclic infrastructure as well. Or to perhaps move the shell UART RX ready polling to a cyclic function.It's also possible to extend the "cyclic" command, to support the creation of periodically executed shell commands (for testing etc).
Here the Azure build, without any issues:
https://dev.azure.com/sr0718/u-boot/_build/results?buildId=219&view=resultsThanks,
StefanAaron Williams (1):
mips:octeon_nic23: Add PCIe FLR fixup via cyclic infrastructureStefan Roese (6):
time: Importtime_after64()and friends from Linux
cyclic: Add basic support for cyclic function execution infrastruture
cyclic: Integrate cyclic infrastructure intoWATCHDOG_RESET
cyclic: Integrate cyclic functionality at bootup in board_r/f
cyclic: Add 'cyclic list' command
sandbox: Add cyclic demo functionMAINTAINERS | 7 + board/Marvell/octeon_nic23/board.c | 197 +++++++++++++++++++++++++++++ board/sandbox/sandbox.c | 15 +++ cmd/Kconfig | 7 + cmd/Makefile | 1 + cmd/cyclic.c | 40 ++++++ common/Kconfig | 20 +++ common/Makefile | 1 + common/board_f.c | 2 + common/board_r.c | 2 + common/cyclic.c | 112 ++++++++++++++++ configs/octeon_nic23_defconfig | 3 + configs/sandbox_defconfig | 3 + fs/cramfs/uncompress.c | 2 +- include/cyclic.h | 97 ++++++++++++++ include/time.h | 19 +++ include/watchdog.h | 23 +++- 17 files changed, 547 insertions(+), 4 deletions(-) create mode 100644 cmd/cyclic.c create mode 100644 common/cyclic.c create mode 100644 include/cyclic.h
Quoted 3 lines
--
2.37.1
This looks interesting. I like the idea of integrating the watchdog stuff too, since you are making use of it.
Would it make sense to make use of the new event system, since it has static and dynamic handlers?
Regards,
Simon
Hi Simon,
Quoted 77 lines · Simon Glass
Hi Stefan,
Quoted 66 lines · Stefan Roese
This patchset adds the basic infrastructure to periodically execute code, e.g. all 100ms. Examples for such functions might be LED blinking etc. The functions that are hooked into this cyclic list should be small timewise as otherwise the execution of the other code that relies on a high frequent polling (e.g. UART rx char ready check) might be delayed too much. This patch also adds the
KconfigoptionCONFIG_CYCLIC_MAX_CPU_TIME_US, which configures the max allowed time for such a cyclic function. If it's execution time exceeds this time, this cyclic function will get removed from the cyclic list.How is this cyclic functionality executed?
This patchset integrates the main function responsible for calling all registered cyclic functionscyclic_run()into the commonWATCHDOG_RESETmacro. This guarantees thatcyclic_run()is executed very often, which is necessary for the cyclic functions to get scheduled and executed at their configured periods.This cyclic infrastructure will be used by a board specific function on the NIC23 MIPS Octeon board, which needs to check periodically, if a PCIe FLR has occurred.
Ideas how to continue:
One idea is to renameWATCHDOG_RESETto something like SCHEDULE and move thewatchdog_resetcall into this cyclic infrastructure as well. Or to perhaps move the shell UART RX ready polling to a cyclic function.It's also possible to extend the "cyclic" command, to support the creation of periodically executed shell commands (for testing etc).
Here the Azure build, without any issues:
https://dev.azure.com/sr0718/u-boot/_build/results?buildId=219&view=resultsThanks,
StefanAaron Williams (1):
mips:octeon_nic23: Add PCIe FLR fixup via cyclic infrastructureStefan Roese (6):
time: Importtime_after64()and friends from Linux
cyclic: Add basic support for cyclic function execution infrastruture
cyclic: Integrate cyclic infrastructure intoWATCHDOG_RESET
cyclic: Integrate cyclic functionality at bootup in board_r/f
cyclic: Add 'cyclic list' command
sandbox: Add cyclic demo functionMAINTAINERS | 7 + board/Marvell/octeon_nic23/board.c | 197 +++++++++++++++++++++++++++++ board/sandbox/sandbox.c | 15 +++ cmd/Kconfig | 7 + cmd/Makefile | 1 + cmd/cyclic.c | 40 ++++++ common/Kconfig | 20 +++ common/Makefile | 1 + common/board_f.c | 2 + common/board_r.c | 2 + common/cyclic.c | 112 ++++++++++++++++ configs/octeon_nic23_defconfig | 3 + configs/sandbox_defconfig | 3 + fs/cramfs/uncompress.c | 2 +- include/cyclic.h | 97 ++++++++++++++ include/time.h | 19 +++ include/watchdog.h | 23 +++- 17 files changed, 547 insertions(+), 4 deletions(-)Quoted 7 lines
create mode 100644
cmd/cyclic.c
create mode 100644common/cyclic.c
create mode 100644include/cyclic.h--
2.37.1
Quoted 5 lines
This looks interesting. I like the idea of integrating the watchdog stuff too, since you are making use of it.
Would it make sense to make use of the new event system, since it has static and dynamic handlers?
IIRC, I tried to make use of this infrastructure but it did not work out. Or do you see some way to integrate this cyclic IF into the event system? FWICT, the only way to get this done is to make use of the (ugly) WATCHDOG_RESET calls.
Thanks,
Stefan
Hi Stefan,
Quoted 84 lines · Stefan Roese
Hi Simon,
Quoted 80 lines · Simon Glass
Hi Stefan,
Quoted 66 lines · Stefan Roese
This patchset adds the basic infrastructure to periodically execute code, e.g. all 100ms. Examples for such functions might be LED blinking etc. The functions that are hooked into this cyclic list should be small timewise as otherwise the execution of the other code that relies on a high frequent polling (e.g. UART rx char ready check) might be delayed too much. This patch also adds the
KconfigoptionCONFIG_CYCLIC_MAX_CPU_TIME_US, which configures the max allowed time for such a cyclic function. If it's execution time exceeds this time, this cyclic function will get removed from the cyclic list.How is this cyclic functionality executed?
This patchset integrates the main function responsible for calling all registered cyclic functionscyclic_run()into the commonWATCHDOG_RESETmacro. This guarantees thatcyclic_run()is executed very often, which is necessary for the cyclic functions to get scheduled and executed at their configured periods.This cyclic infrastructure will be used by a board specific function on the NIC23 MIPS Octeon board, which needs to check periodically, if a PCIe FLR has occurred.
Ideas how to continue:
One idea is to renameWATCHDOG_RESETto something like SCHEDULE and move thewatchdog_resetcall into this cyclic infrastructure as well. Or to perhaps move the shell UART RX ready polling to a cyclic function.It's also possible to extend the "cyclic" command, to support the creation of periodically executed shell commands (for testing etc).
Here the Azure build, without any issues:
https://dev.azure.com/sr0718/u-boot/_build/results?buildId=219&view=resultsThanks,
StefanAaron Williams (1):
mips:octeon_nic23: Add PCIe FLR fixup via cyclic infrastructureStefan Roese (6):
time: Importtime_after64()and friends from Linux
cyclic: Add basic support for cyclic function execution infrastruture
cyclic: Integrate cyclic infrastructure intoWATCHDOG_RESET
cyclic: Integrate cyclic functionality at bootup in board_r/f
cyclic: Add 'cyclic list' command
sandbox: Add cyclic demo functionMAINTAINERS | 7 + board/Marvell/octeon_nic23/board.c | 197 +++++++++++++++++++++++++++++ board/sandbox/sandbox.c | 15 +++ cmd/Kconfig | 7 + cmd/Makefile | 1 + cmd/cyclic.c | 40 ++++++ common/Kconfig | 20 +++ common/Makefile | 1 + common/board_f.c | 2 + common/board_r.c | 2 + common/cyclic.c | 112 ++++++++++++++++ configs/octeon_nic23_defconfig | 3 + configs/sandbox_defconfig | 3 + fs/cramfs/uncompress.c | 2 +- include/cyclic.h | 97 ++++++++++++++ include/time.h | 19 +++ include/watchdog.h | 23 +++- 17 files changed, 547 insertions(+), 4 deletions(-)Quoted 7 lines
create mode 100644
cmd/cyclic.c
create mode 100644common/cyclic.c
create mode 100644include/cyclic.h--
2.37.1This looks interesting. I like the idea of integrating the watchdog stuff too, since you are making use of it.
Quoted 7 lines
Quoted 2 lines
Would it make sense to make use of the new event system, since it has static and dynamic handlers?
IIRC, I tried to make use of this infrastructure but it did not work out. Or do you see some way to integrate this cyclic IF into the event system? FWICT, the only way to get this done is to make use of the (ugly)
WATCHDOG_RESETcalls.
Yes that makes sense. I don't see another way.
But within that, one option would be to send an event every time WATCHDOG_RESET is used, and have things register as an event spy, thus making use of that existing system. The event feature is not enabled by default, but it could be enabled when this functionality is needed.
Regards,
Simon
Hi Simon,
Quoted 95 lines · Simon Glass
Hi Stefan,
Quoted 84 lines · Stefan Roese
Hi Simon,
Quoted 80 lines · Simon Glass
Hi Stefan,
Quoted 66 lines · Stefan Roese
This patchset adds the basic infrastructure to periodically execute code, e.g. all 100ms. Examples for such functions might be LED blinking etc. The functions that are hooked into this cyclic list should be small timewise as otherwise the execution of the other code that relies on a high frequent polling (e.g. UART rx char ready check) might be delayed too much. This patch also adds the
KconfigoptionCONFIG_CYCLIC_MAX_CPU_TIME_US, which configures the max allowed time for such a cyclic function. If it's execution time exceeds this time, this cyclic function will get removed from the cyclic list.How is this cyclic functionality executed?
This patchset integrates the main function responsible for calling all registered cyclic functionscyclic_run()into the commonWATCHDOG_RESETmacro. This guarantees thatcyclic_run()is executed very often, which is necessary for the cyclic functions to get scheduled and executed at their configured periods.This cyclic infrastructure will be used by a board specific function on the NIC23 MIPS Octeon board, which needs to check periodically, if a PCIe FLR has occurred.
Ideas how to continue:
One idea is to renameWATCHDOG_RESETto something like SCHEDULE and move thewatchdog_resetcall into this cyclic infrastructure as well. Or to perhaps move the shell UART RX ready polling to a cyclic function.It's also possible to extend the "cyclic" command, to support the creation of periodically executed shell commands (for testing etc).
Here the Azure build, without any issues:
https://dev.azure.com/sr0718/u-boot/_build/results?buildId=219&view=resultsThanks,
StefanAaron Williams (1):
mips:octeon_nic23: Add PCIe FLR fixup via cyclic infrastructureStefan Roese (6):
time: Importtime_after64()and friends from Linux
cyclic: Add basic support for cyclic function execution infrastruture
cyclic: Integrate cyclic infrastructure intoWATCHDOG_RESET
cyclic: Integrate cyclic functionality at bootup in board_r/f
cyclic: Add 'cyclic list' command
sandbox: Add cyclic demo functionMAINTAINERS | 7 + board/Marvell/octeon_nic23/board.c | 197 +++++++++++++++++++++++++++++ board/sandbox/sandbox.c | 15 +++ cmd/Kconfig | 7 + cmd/Makefile | 1 + cmd/cyclic.c | 40 ++++++ common/Kconfig | 20 +++ common/Makefile | 1 + common/board_f.c | 2 + common/board_r.c | 2 + common/cyclic.c | 112 ++++++++++++++++ configs/octeon_nic23_defconfig | 3 + configs/sandbox_defconfig | 3 + fs/cramfs/uncompress.c | 2 +- include/cyclic.h | 97 ++++++++++++++ include/time.h | 19 +++ include/watchdog.h | 23 +++- 17 files changed, 547 insertions(+), 4 deletions(-)Quoted 7 lines
create mode 100644
cmd/cyclic.c
create mode 100644common/cyclic.c
create mode 100644include/cyclic.h--
2.37.1This looks interesting. I like the idea of integrating the watchdog stuff too, since you are making use of it.
Quoted 7 lines
Quoted 2 lines
Would it make sense to make use of the new event system, since it has static and dynamic handlers?
IIRC, I tried to make use of this infrastructure but it did not work out. Or do you see some way to integrate this cyclic IF into the event system? FWICT, the only way to get this done is to make use of the (ugly)
WATCHDOG_RESETcalls.
Quoted 6 lines
Yes that makes sense. I don't see another way.
But within that, one option would be to send an event every time
WATCHDOG_RESETis used, and have things register as an event spy, thus making use of that existing system. The event feature is not enabled by default, but it could be enabled when this functionality is needed.
I still need to double-check, sorry: You are thinking about this call- trace:
WATCHDOG_RESET -> event IF -> cylic IF -> cylic user
?
If yes, what would be the advantage(s) against implementing this separately?
Thanks,
Stefan
Hi Stefan,
Quoted 106 lines · Stefan Roese
Hi Simon,
Quoted 95 lines · Simon Glass
Hi Stefan,
Quoted 84 lines · Stefan Roese
Hi Simon,
Quoted 80 lines · Simon Glass
Hi Stefan,
Quoted 66 lines · Stefan Roese
This patchset adds the basic infrastructure to periodically execute code, e.g. all 100ms. Examples for such functions might be LED blinking etc. The functions that are hooked into this cyclic list should be small timewise as otherwise the execution of the other code that relies on a high frequent polling (e.g. UART rx char ready check) might be delayed too much. This patch also adds the
KconfigoptionCONFIG_CYCLIC_MAX_CPU_TIME_US, which configures the max allowed time for such a cyclic function. If it's execution time exceeds this time, this cyclic function will get removed from the cyclic list.How is this cyclic functionality executed?
This patchset integrates the main function responsible for calling all registered cyclic functionscyclic_run()into the commonWATCHDOG_RESETmacro. This guarantees thatcyclic_run()is executed very often, which is necessary for the cyclic functions to get scheduled and executed at their configured periods.This cyclic infrastructure will be used by a board specific function on the NIC23 MIPS Octeon board, which needs to check periodically, if a PCIe FLR has occurred.
Ideas how to continue:
One idea is to renameWATCHDOG_RESETto something like SCHEDULE and move thewatchdog_resetcall into this cyclic infrastructure as well. Or to perhaps move the shell UART RX ready polling to a cyclic function.It's also possible to extend the "cyclic" command, to support the creation of periodically executed shell commands (for testing etc).
Here the Azure build, without any issues:
https://dev.azure.com/sr0718/u-boot/_build/results?buildId=219&view=resultsThanks,
StefanAaron Williams (1):
mips:octeon_nic23: Add PCIe FLR fixup via cyclic infrastructureStefan Roese (6):
time: Importtime_after64()and friends from Linux
cyclic: Add basic support for cyclic function execution infrastruture
cyclic: Integrate cyclic infrastructure intoWATCHDOG_RESET
cyclic: Integrate cyclic functionality at bootup in board_r/f
cyclic: Add 'cyclic list' command
sandbox: Add cyclic demo functionMAINTAINERS | 7 + board/Marvell/octeon_nic23/board.c | 197 +++++++++++++++++++++++++++++ board/sandbox/sandbox.c | 15 +++ cmd/Kconfig | 7 + cmd/Makefile | 1 + cmd/cyclic.c | 40 ++++++ common/Kconfig | 20 +++ common/Makefile | 1 + common/board_f.c | 2 + common/board_r.c | 2 + common/cyclic.c | 112 ++++++++++++++++ configs/octeon_nic23_defconfig | 3 + configs/sandbox_defconfig | 3 + fs/cramfs/uncompress.c | 2 +- include/cyclic.h | 97 ++++++++++++++ include/time.h | 19 +++ include/watchdog.h | 23 +++- 17 files changed, 547 insertions(+), 4 deletions(-)Quoted 7 lines
create mode 100644
cmd/cyclic.c
create mode 100644common/cyclic.c
create mode 100644include/cyclic.h--
2.37.1This looks interesting. I like the idea of integrating the watchdog stuff too, since you are making use of it.
Quoted 7 lines
Quoted 2 lines
Would it make sense to make use of the new event system, since it has static and dynamic handlers?
IIRC, I tried to make use of this infrastructure but it did not work out. Or do you see some way to integrate this cyclic IF into the event system? FWICT, the only way to get this done is to make use of the (ugly)
WATCHDOG_RESETcalls.Quoted 6 lines
Yes that makes sense. I don't see another way.
But within that, one option would be to send an event every time
WATCHDOG_RESETis used, and have things register as an event spy, thus making use of that existing system. The event feature is not enabled by default, but it could be enabled when this functionality is needed.
Quoted 5 lines
I still need to double-check, sorry: You are thinking about this call- trace:
WATCHDOG_RESET-> event IF -> cylic IF -> cylic user
More this, i.e. I am wondering if the cyclic functionality can be done using events.
WATCHDOG_RESET -> sends watchdog event -> event spy receives event
Quoted 4 lines
?
If yes, what would be the advantage(s) against implementing this separately?
It would need handling of max CPU time and perhaps some other tweaks, but it would result in less code (?) and one less thing for people to learn. The cyclic command could still be provided if that is useful, by showing only cyclic certain event handlers.
Regards,
Simon
Hi Simon,
Quoted 112 lines · Simon Glass
Hi Stefan,
Quoted 109 lines · Stefan Roese
Hi Simon,
Quoted 95 lines · Simon Glass
Hi Stefan,
Quoted 84 lines · Stefan Roese
Hi Simon,
Quoted 80 lines · Simon Glass
Hi Stefan,
Quoted 70 lines · Stefan Roese
This patchset adds the basic infrastructure to periodically execute code, e.g. all 100ms. Examples for such functions might be LED blinking etc. The functions that are hooked into this cyclic list should be small timewise as otherwise the execution of the other code that relies on a high frequent polling (e.g. UART rx char ready check) might be delayed too much. This patch also adds the
KconfigoptionCONFIG_CYCLIC_MAX_CPU_TIME_US, which configures the max allowed time for such a cyclic function. If it's execution time exceeds this time, this cyclic function will get removed from the cyclic list.How is this cyclic functionality executed?
This patchset integrates the main function responsible for calling all registered cyclic functionscyclic_run()into the commonWATCHDOG_RESETmacro. This guarantees thatcyclic_run()is executed very often, which is necessary for the cyclic functions to get scheduled and executed at their configured periods.This cyclic infrastructure will be used by a board specific function on the NIC23 MIPS Octeon board, which needs to check periodically, if a PCIe FLR has occurred.
Ideas how to continue:
One idea is to renameWATCHDOG_RESETto something like SCHEDULE and move thewatchdog_resetcall into this cyclic infrastructure as well. Or to perhaps move the shell UART RX ready polling to a cyclic function.It's also possible to extend the "cyclic" command, to support the creation of periodically executed shell commands (for testing etc).
Here the Azure build, without any issues:
https://dev.azure.com/sr0718/u-boot/_build/results?buildId=219&view=resultsThanks,
StefanAaron Williams (1):
mips:octeon_nic23: Add PCIe FLR fixup via cyclic infrastructureStefan Roese (6):
time: Importtime_after64()and friends from Linux
cyclic: Add basic support for cyclic function execution infrastruture
cyclic: Integrate cyclic infrastructure intoWATCHDOG_RESET
cyclic: Integrate cyclic functionality at bootup in board_r/f
cyclic: Add 'cyclic list' command
sandbox: Add cyclic demo function
MAINTAINERS| 7 +
board/Marvell/octeon_nic23/board.c| 197 +++++++++++++++++++++++++++++
board/sandbox/sandbox.c| 15 +++
cmd/Kconfig | 7 +
cmd/Makefile | 1 +
cmd/cyclic.c| 40 ++++++
common/Kconfig | 20 +++
common/Makefile | 1 +
common/board_f.c| 2 +
common/board_r.c| 2 +
common/cyclic.c| 112 ++++++++++++++++
configs/octeon_nic23_defconfig | 3 +
configs/sandbox_defconfig | 3 +
fs/cramfs/uncompress.c| 2 +-
include/cyclic.h| 97 ++++++++++++++
include/time.h| 19 +++
include/watchdog.h| 23 +++-
17 files changed, 547 insertions(+), 4 deletions(-)
create mode 100644cmd/cyclic.c
create mode 100644common/cyclic.c
create mode 100644include/cyclic.hQuoted 3 lines
--
2.37.1This looks interesting. I like the idea of integrating the watchdog stuff too, since you are making use of it.
Quoted 7 lines
Quoted 2 lines
Would it make sense to make use of the new event system, since it has static and dynamic handlers?
IIRC, I tried to make use of this infrastructure but it did not work out. Or do you see some way to integrate this cyclic IF into the event system? FWICT, the only way to get this done is to make use of the (ugly)
WATCHDOG_RESETcalls.Quoted 6 lines
Yes that makes sense. I don't see another way.
But within that, one option would be to send an event every time
WATCHDOG_RESETis used, and have things register as an event spy, thus making use of that existing system. The event feature is not enabled by default, but it could be enabled when this functionality is needed.I still need to double-check, sorry: You are thinking about this call- trace:
Quoted 7 lines
Quoted 2 lines
WATCHDOG_RESET-> event IF -> cylic IF -> cylic userMore this, i.e. I am wondering if the cyclic functionality can be done using events.
WATCHDOG_RESET-> sends watchdog event -> event spy receives event
This would mean in the end, that all U-Boot targets would need to enable the event subsystem as well. This might lead to problems with image sizes on some of those especially old/ancient targets. Hmmm...
Quoted 9 lines
Quoted 4 lines
?
If yes, what would be the advantage(s) against implementing this separately?
It would need handling of max CPU time and perhaps some other tweaks, but it would result in less code (?) and one less thing for people to learn. The cyclic command could still be provided if that is useful, by showing only cyclic certain event handlers.
Frankly, I'm not 100% convinced that this would really result in less code. Or even worse, it could (?) result in more complex code, as both interfaces are in the same area but still handle different tasks, e.g. synchronous vs. asynchronous.
So my preference would be to continue on my current path. I'll integrate some documentation in my next patchset version and will resubmit hopefully sometime later this week.
Thanks,
Stefan
Hi Stefan,
Quoted 119 lines · Stefan Roese
Hi Simon,
Quoted 115 lines · Simon Glass
Hi Stefan,
Quoted 111 lines · Stefan Roese
Hi Simon,
Quoted 95 lines · Simon Glass
Hi Stefan,
Quoted 84 lines · Stefan Roese
Hi Simon,
Quoted 80 lines · Simon Glass
Hi Stefan,
Quoted 70 lines · Stefan Roese
This patchset adds the basic infrastructure to periodically execute code, e.g. all 100ms. Examples for such functions might be LED blinking etc. The functions that are hooked into this cyclic list should be small timewise as otherwise the execution of the other code that relies on a high frequent polling (e.g. UART rx char ready check) might be delayed too much. This patch also adds the
KconfigoptionCONFIG_CYCLIC_MAX_CPU_TIME_US, which configures the max allowed time for such a cyclic function. If it's execution time exceeds this time, this cyclic function will get removed from the cyclic list.How is this cyclic functionality executed?
This patchset integrates the main function responsible for calling all registered cyclic functionscyclic_run()into the commonWATCHDOG_RESETmacro. This guarantees thatcyclic_run()is executed very often, which is necessary for the cyclic functions to get scheduled and executed at their configured periods.This cyclic infrastructure will be used by a board specific function on the NIC23 MIPS Octeon board, which needs to check periodically, if a PCIe FLR has occurred.
Ideas how to continue:
One idea is to renameWATCHDOG_RESETto something like SCHEDULE and move thewatchdog_resetcall into this cyclic infrastructure as well. Or to perhaps move the shell UART RX ready polling to a cyclic function.It's also possible to extend the "cyclic" command, to support the creation of periodically executed shell commands (for testing etc).
Here the Azure build, without any issues:
https://dev.azure.com/sr0718/u-boot/_build/results?buildId=219&view=resultsThanks,
StefanAaron Williams (1):
mips:octeon_nic23: Add PCIe FLR fixup via cyclic infrastructureStefan Roese (6):
time: Importtime_after64()and friends from Linux
cyclic: Add basic support for cyclic function execution infrastruture
cyclic: Integrate cyclic infrastructure intoWATCHDOG_RESET
cyclic: Integrate cyclic functionality at bootup in board_r/f
cyclic: Add 'cyclic list' command
sandbox: Add cyclic demo function
MAINTAINERS| 7 +
board/Marvell/octeon_nic23/board.c| 197 +++++++++++++++++++++++++++++
board/sandbox/sandbox.c| 15 +++
cmd/Kconfig | 7 +
cmd/Makefile | 1 +
cmd/cyclic.c| 40 ++++++
common/Kconfig | 20 +++
common/Makefile | 1 +
common/board_f.c| 2 +
common/board_r.c| 2 +
common/cyclic.c| 112 ++++++++++++++++
configs/octeon_nic23_defconfig | 3 +
configs/sandbox_defconfig | 3 +
fs/cramfs/uncompress.c| 2 +-
include/cyclic.h| 97 ++++++++++++++
include/time.h| 19 +++
include/watchdog.h| 23 +++-
17 files changed, 547 insertions(+), 4 deletions(-)
create mode 100644cmd/cyclic.c
create mode 100644common/cyclic.c
create mode 100644include/cyclic.hQuoted 3 lines
--
2.37.1This looks interesting. I like the idea of integrating the watchdog stuff too, since you are making use of it.
Quoted 7 lines
Quoted 2 lines
Would it make sense to make use of the new event system, since it has static and dynamic handlers?
IIRC, I tried to make use of this infrastructure but it did not work out. Or do you see some way to integrate this cyclic IF into the event system? FWICT, the only way to get this done is to make use of the (ugly)
WATCHDOG_RESETcalls.Quoted 6 lines
Yes that makes sense. I don't see another way.
But within that, one option would be to send an event every time
WATCHDOG_RESETis used, and have things register as an event spy, thus making use of that existing system. The event feature is not enabled by default, but it could be enabled when this functionality is needed.I still need to double-check, sorry: You are thinking about this call- trace:
WATCHDOG_RESET-> event IF -> cylic IF -> cylic user
Quoted 8 lines
Quoted 4 lines
More this, i.e. I am wondering if the cyclic functionality can be done using events.
WATCHDOG_RESET-> sends watchdog event -> event spy receives eventThis would mean in the end, that all U-Boot targets would need to enable the event subsystem as well. This might lead to problems with image sizes on some of those especially old/ancient targets. Hmmm...
It depends on whether cyclic is a small adder to events or something larger. Actually events are not too big, but having 'dynamic' ones (allocated at runtime) does add a bit more.
Quoted 11 lines
Quoted 10 lines
Quoted 5 lines
?
If yes, what would be the advantage(s) against implementing this separately?
It would need handling of max CPU time and perhaps some other tweaks, but it would result in less code (?) and one less thing for people to learn. The cyclic command could still be provided if that is useful, by showing only cyclic certain event handlers.
Quoted 8 lines
Frankly, I'm not 100% convinced that this would really result in less code. Or even worse, it could (?) result in more complex code, as both interfaces are in the same area but still handle different tasks, e.g. synchronous vs. asynchronous.
So my preference would be to continue on my current path. I'll integrate some documentation in my next patchset version and will resubmit hopefully sometime later this week.
OK, sounds good. You are writing the code :-)
Regards,
Simon
Quoted 21 lines · Stefan Roese
This patchset adds the basic infrastructure to periodically execute code, e.g. all 100ms. Examples for such functions might be LED blinking etc. The functions that are hooked into this cyclic list should be small timewise as otherwise the execution of the other code that relies on a high frequent polling (e.g. UART rx char ready check) might be delayed too much. This patch also adds the
KconfigoptionCONFIG_CYCLIC_MAX_CPU_TIME_US, which configures the max allowed time for such a cyclic function. If it's execution time exceeds this time, this cyclic function will get removed from the cyclic list.How is this cyclic functionality executed?
This patchset integrates the main function responsible for calling all registered cyclic functionscyclic_run()into the commonWATCHDOG_RESETmacro. This guarantees thatcyclic_run()is executed very often, which is necessary for the cyclic functions to get scheduled and executed at their configured periods.This cyclic infrastructure will be used by a board specific function on the NIC23 MIPS Octeon board, which needs to check periodically, if a PCIe FLR has occurred.
Quoted 5 lines
Ideas how to continue:
One idea is to renameWATCHDOG_RESETto something like SCHEDULE and move thewatchdog_resetcall into this cyclic infrastructure as well. Or to perhaps move the shell UART RX ready polling to a cyclic function.
Hello Stefan
I am missing rework defining where WATCHDOG_RESET has to be called:
WATCHDOG_RESET is called in net_loop() but not in eth_rx() and eth_tx(). This is clearly the wrong place as not all network traffic uses net_loop().
Same is true for your reference to UART rx. WATCHDOG_RESET is called in individual UART drivers. But this does not help if tstc() is calling usb_kbd_testc().
So before adding this patchset please provide the concept defining where WATCHDOG_RESET should be invoked.
A framework like the one proposed requires documentation. This needs to be an integral part of the next version of the series.
With the infrastructure you are building efi_timer_check() is a candidate for refactoring. Currently efi_timer_check() is called whenever the EFI sub-system is waiting for anything (keyboard input, polling events, network I/O).
Best regards
Heinrich
Quoted 43 lines
It's also possible to extend the "cyclic" command, to support the creation of periodically executed shell commands (for testing etc).
Here the Azure build, without any issues:
https://dev.azure.com/sr0718/u-boot/_build/results?buildId=219&view=resultsThanks,
StefanAaron Williams (1):
mips:octeon_nic23: Add PCIe FLR fixup via cyclic infrastructureStefan Roese (6):
time: Importtime_after64()and friends from Linux
cyclic: Add basic support for cyclic function execution infrastruture
cyclic: Integrate cyclic infrastructure intoWATCHDOG_RESET
cyclic: Integrate cyclic functionality at bootup in board_r/f
cyclic: Add 'cyclic list' command
sandbox: Add cyclic demo functionMAINTAINERS | 7 + board/Marvell/octeon_nic23/board.c | 197 +++++++++++++++++++++++++++++ board/sandbox/sandbox.c | 15 +++ cmd/Kconfig | 7 + cmd/Makefile | 1 + cmd/cyclic.c | 40 ++++++ common/Kconfig | 20 +++ common/Makefile | 1 + common/board_f.c | 2 + common/board_r.c | 2 + common/cyclic.c | 112 ++++++++++++++++ configs/octeon_nic23_defconfig | 3 + configs/sandbox_defconfig | 3 + fs/cramfs/uncompress.c | 2 +- include/cyclic.h | 97 ++++++++++++++ include/time.h | 19 +++ include/watchdog.h | 23 +++- 17 files changed, 547 insertions(+), 4 deletions(-)create mode 100644
cmd/cyclic.c
create mode 100644common/cyclic.c
create mode 100644include/cyclic.h
Hi Heinrich,
Quoted 35 lines · Heinrich Schuchardt
Quoted 21 lines · Stefan Roese
This patchset adds the basic infrastructure to periodically execute code, e.g. all 100ms. Examples for such functions might be LED blinking etc. The functions that are hooked into this cyclic list should be small timewise as otherwise the execution of the other code that relies on a high frequent polling (e.g. UART rx char ready check) might be delayed too much. This patch also adds the
KconfigoptionCONFIG_CYCLIC_MAX_CPU_TIME_US, which configures the max allowed time for such a cyclic function. If it's execution time exceeds this time, this cyclic function will get removed from the cyclic list.How is this cyclic functionality executed?
This patchset integrates the main function responsible for calling all registered cyclic functionscyclic_run()into the commonWATCHDOG_RESETmacro. This guarantees thatcyclic_run()is executed very often, which is necessary for the cyclic functions to get scheduled and executed at their configured periods.This cyclic infrastructure will be used by a board specific function on the NIC23 MIPS Octeon board, which needs to check periodically, if a PCIe FLR has occurred.
Quoted 5 lines
Ideas how to continue:
One idea is to renameWATCHDOG_RESETto something like SCHEDULE and move thewatchdog_resetcall into this cyclic infrastructure as well. Or to perhaps move the shell UART RX ready polling to a cyclic function.Hello Stefan
I am missing rework defining where
WATCHDOG_RESEThas to be called:
WATCHDOG_RESETis called innet_loop()but not ineth_rx()andeth_tx(). This is clearly the wrong place as not all network traffic usesnet_loop().
Quoted 6 lines
Same is true for your reference to UART rx.
WATCHDOG_RESETis called in individual UART drivers. But this does not help iftstc()is callingusb_kbd_testc().So before adding this patchset please provide the concept defining where
WATCHDOG_RESETshould be invoked.
I agree that you are addressing valid points here. But this patchset is not intended to change the WATCHDOG_RESET functionality. These WDT calls and their integration (sprinkling) in the U-Boot source are very ancient. I intentionally did not change anything here to not break / change anything in this area for now.
The points listed from you above are all valid and most likely good improvements or even fixes to the watchdog and once accepted also the cyclic infrastructure. Still I think it makes much sense to address them, once this patchset is in mainline. After this, many improvements might be done, like:
- Integrate WDT IF as a "user" into the cyclic IF
- Rename WATCHDOG_RESET to something better matching its functionality
- Improve locations, from where these cyclic IF is called (see your suggestions above)
- ...
Quoted 2 lines
A framework like the one proposed requires documentation. This needs to be an integral part of the next version of the series.
Ok, I admit that I'm a bit lazy here. I'll add some documentation in the next version.
Quoted 4 lines
With the infrastructure you are building
efi_timer_check()is a candidate for refactoring. Currentlyefi_timer_check()is called whenever the EFI sub-system is waiting for anything (keyboard input, polling events, network I/O).
Interesting. I have to admit that my internal knowledge of the EFI subsystem in U-Boot is a bit "limited". If you see improvements to this cyclic IF that should be made, so that this cyclic IF is even more generic and can better be used by e.g. efi_timer_check(), please let me know.
Thanks,
Stefan