Skip to contentSkip to conversation

still ongoing problems using minicom to talk to u-boot?

U-Boot Robert P. J. Day 3 participants 5 messages Aug 19, 2009

lore
Share & tools
lore
#0 lore raw

the current u-boot manual suggests there are still problems using
minicom to connect to u-boot. does anyone know what those problems are, and if they still exist?

i've been using minicom to connect to the pre-installed u-boot on my
beagleboard for months now, and it's worked reliably, except for one situation. since my laptop has no serial port, i'd purchased a low-end USB-serial converter (with a prolific chipset), which failed utterly. i tried everything to debug my setup until someone else suggested that the converter was at fault.

i purchased a different converter and everything was fine. so i'm
still curious about potential problems with minicom and u-boot.

rday
--

========================================================================
Robert P. J. Day Waterloo, Ontario, CANADA

Linux Consulting, Training and Annoying Kernel Pedantry.

Web page:                                          http://crashcourse.ca
Twitter:                                       http://twitter.com/rpjday

========================================================================

#1 lore raw

Dear "Robert P. J. Day",

Quoted 3 lines · In message <alpine.LFD.2.00.0908190554330.8008@localhost> you wrote:

i purchased a different converter and everything was fine. so i'm
still curious about potential problems with minicom and u-boot.

Just RTFM: http://www.denx.de/wiki/view/DULG/SystemSetup#Section_4.4.

Best regards,

Wolfgang Denk

Signature · 5 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
"It is better to have tried and failed than to have  failed  to  try,
but the result's the same."                           - Mike Dennison
#2 lore raw
Quoted 8 lines · Wolfgang Denk

Dear "Robert P. J. Day",

Quoted 3 lines · In message <alpine.LFD.2.00.0908190554330.8008@localhost> you wrote:

i purchased a different converter and everything was fine. so i'm
still curious about potential problems with minicom and u-boot.

Just RTFM: http://www.denx.de/wiki/view/DULG/SystemSetup#Section_4.4.

i *did* read that, which is why i was asking. i'm trying to figure
out *what* specific problem minicom has that is avoided by the use of cu or kermit, something that short section doesn't address.

rday
--

========================================================================
Robert P. J. Day Waterloo, Ontario, CANADA

Linux Consulting, Training and Annoying Kernel Pedantry.

Web page:                                          http://crashcourse.ca
Twitter:                                       http://twitter.com/rpjday

========================================================================

#3 lore raw

Dear "Robert P. J. Day",

Quoted 4 lines · In message <alpine.LFD.2.00.0908190639480.16337@localhost> you wrote:

i *did* read that, which is why i was asking. i'm trying to figure
out *what* specific problem minicom has that is avoided by the use of cu or kermit, something that short section doesn't address.

It is not one specific problem. minicom is just crap. Dump it.

I mean, if there were no altrernativs around, one would probably bother to fix at least the most pressing issues, but there is plenty wroking alternatives, so who cares?

Best regards,

Wolfgang Denk

Signature · 5 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Do not follow where the path may lead....go instead where there is no
path and leave a trail.
#4 lore raw

hi,

Quoted 10 lines · Wolfgang Denk

Dear "Robert P. J. Day",

Quoted 4 lines · In message <alpine.LFD.2.00.0908190639480.16337@localhost> you wrote:

i *did* read that, which is why i was asking. i'm trying to figure
out *what* specific problem minicom has that is avoided by the use of cu or kermit, something that short section doesn't address.

It is not one specific problem. minicom is just crap. Dump it.

i am using minicom to download u-boot using serial console(at91rm9200dk).
it needs a seperate program for xmodem.
I got this program from net. it is attached.

Quoted 8 lines

I mean, if there were no altrernativs around, one would probably bother to fix at least the most pressing issues, but there is plenty wroking alternatives, so who cares?

Best regards,

Wolfgang Denk

-------------- next part --------------
A non-text attachment was scrubbed...
Name: sx-at91.c
Type: text/x-csrc
Size: 8021 bytes
Desc: not available
Url : http://lists.denx.de/pipermail/u-boot/attachments/20090819/05c1f6a2/attachment.c