Skip to contentSkip to conversation

time: logrithmic time accumulation

PATCH In review john stultz 4 participants 11 messages Oct 2, 2009 – Oct 7, 2009 Timekeeping, clocksource core, NTP, alarmtimer

lore
Share & tools
lore
#0 lore raw

PATCH 1/2 time: logrithmic time accumulation

Accumulating one tick at a time works well unless we're using NOHZ. Then it can be an issue, since we may have to run through the loop a few thousand times, which can increase timer interrupt caused latency.

The current solution was to accumulate in half-second intervals with NOHZ. This kept the number of loops down, however it did slightly change how we make NTP adjustments. While not an issue with NTPd users, as NTPd makes adjustments over a longer period of time, other adjtimex() users have noticed the half-second granularity with which we can apply frequency changes to the clock.

For instance, if a application tries to apply a 100ppm frequency correction for 20ms to correct a 2us offset, with NOHZ they either get no correction, or a 50us correction.

Now, there will always be some granularity error for applying frequency corrections. However with users sensitive to this error have seen a 50-500x increase with NOHZ compared to running without NOHZ.

So I figured I'd try another approach then just simply increasing the interval. My approach is to consume the time interval logarithmically. This reduces the number of times through the loop needed keeping latency down, while still preserving the original granularity error for adjtimex() changes.

Further, this change allows us to remove the xtime_cache code (patch to follow), as xtime is always within one tick of the current time, instead of the half-second updates it saw before.

An earlier version of this patch has been shipping to x86 users in the RedHat MRG releases for awhile without issue, but I've reworked this version to be even more careful about avoiding possible overflows if the shift value gets too large.

Since this is not the most trivial code, and its slightly different then whats been tested for awhile, it would be good to get this into some trees for testing. Be it -tip or -mm, either would work. If there's no problems it could be a 2.6.33 or 2.6.34 item.

Any comments or feedback would be appreciated!

include/linux/timex.h +0 -4
index e6967d1..0c0ef7d 100644
@@ -261,11 +261,7 @@ static inline int ntp_synced(void)
 
 #define NTP_SCALE_SHIFT		32
 
-#ifdef CONFIG_NO_HZ
-#define NTP_INTERVAL_FREQ  (2)
-#else
 #define NTP_INTERVAL_FREQ  (HZ)
-#endif
 #define NTP_INTERVAL_LENGTH (NSEC_PER_SEC/NTP_INTERVAL_FREQ)
 
 /* Returns how long ticks are at present, in ns / 2^NTP_SCALE_SHIFT. */
kernel/time/timekeeping.c +60 -25

105 lines not on this page · raw message

#1 lore raw

PATCH 2/2 time: remove xtime_cache

With the prior logarithmic time accumulation patch, xtime will now always be within one "tick" of the current time, instead of possibly half a second off.

This removes the need for the xtime_cache value, which always stored the time at the last interrupt, so this patch cleans that up removing the xtime_cache related code.

This is a bit simpler, but still could use some wider testing.

Any comments or feedback would be appreciated!

thanks
-john

kernel/time.c +0 -1
index 2e2e469..2ef4fe2 100644
@@ -136,7 +136,6 @@ static inline void warp_clock(void)
 	write_seqlock_irq(&xtime_lock);
 	wall_to_monotonic.tv_sec -= sys_tz.tz_minuteswest * 60;
 	xtime.tv_sec += sys_tz.tz_minuteswest * 60;
-	update_xtime_cache(0);
 	write_sequnlock_irq(&xtime_lock);
 	clock_was_set();
 }
kernel/time/timekeeping.c +4 -23
index 4cc5656..a1513d0 100644
@@ -164,13 +164,6 @@ struct timespec raw_time;
 /* flag for if timekeeping is suspended */
 int __read_mostly timekeeping_suspended;
 
-static struct timespec xtime_cache __attribute__ ((aligned (16)));
-void update_xtime_cache(u64 nsec)
-{
-	xtime_cache = xtime;
-	timespec_add_ns(&xtime_cache, nsec);
-}
-
 /* must hold xtime_lock */
 void timekeeping_leap_insert(int leapsecond)
 {
@@ -331,8 +324,6 @@ int do_settimeofday(struct timespec *tv)
 
 	xtime = *tv;
 
-	update_xtime_cache(0);
-
 	timekeeper.ntp_error = 0;
 	ntp_clear();
 
@@ -547,7 +538,6 @@ void __init timekeeping_init(void)
 	}
 	set_normalized_timespec(&wall_to_monotonic,
 				-boot.tv_sec, -boot.tv_nsec);
-	update_xtime_cache(0);
 	total_sleep_time.tv_sec = 0;
 	total_sleep_time.tv_nsec = 0;
 	write_sequnlock_irqrestore(&xtime_lock, flags);
@@ -581,7 +571,6 @@ static int timekeeping_resume(struct sys_device *dev)
 		wall_to_monotonic = timespec_sub(wall_to_monotonic, ts);
 		total_sleep_time = timespec_add_safe(total_sleep_time, ts);
 	}
-	update_xtime_cache(0);
 	/* re-base the last cycle value */
 	timekeeper.clock->cycle_last = timekeeper.clock->read(timekeeper.clock);
 	timekeeper.ntp_error = 0;
@@ -721,7 +710,6 @@ static void timekeeping_adjust(s64 offset)
 				timekeeper.ntp_error_shift;
 }
 
-
 /**
  * logarithmic_accumulation - shifted accumulation of cycles
  *
@@ -765,7 +753,6 @@ static cycle_t logarithmic_accumulation(cycle_t offset, int shift)
 	return offset;
 }
 
-
 /**
  * update_wall_time - Uses the current clocksource to increment the wall time
  *
@@ -775,7 +762,6 @@ void update_wall_time(void)
 {
 	struct clocksource *clock;
 	cycle_t offset;
-	u64 nsecs;
 	int shift = 0, maxshift;
 
 	/* Make sure we're fully resumed: */
@@ -841,9 +827,6 @@ void update_wall_time(void)
 	timekeeper.ntp_error +=	timekeeper.xtime_nsec <<
 				timekeeper.ntp_error_shift;
 
-	nsecs = clocksource_cyc2ns(offset, timekeeper.mult, timekeeper.shift);
-	update_xtime_cache(nsecs);
-
 	/* check to see if there is a new clocksource to use */
 	update_vsyscall(&xtime, timekeeper.clock);
 }
@@ -880,13 +863,13 @@ void monotonic_to_bootbased(struct timespec *ts)
 
 unsigned long get_seconds(void)
 {
-	return xtime_cache.tv_sec;
+	return xtime.tv_sec;
 }
 EXPORT_SYMBOL(get_seconds);
 
 struct timespec __current_kernel_time(void)
 {
-	return xtime_cache;
+	return xtime;
 }
 
 struct timespec current_kernel_time(void)
@@ -896,8 +879,7 @@ struct timespec current_kernel_time(void)
 
 	do {
 		seq = read_seqbegin(&xtime_lock);
-
-		now = xtime_cache;
+		now = xtime;
 	} while (read_seqretry(&xtime_lock, seq));
 
 	return now;
@@ -911,8 +893,7 @@ struct timespec get_monotonic_coarse(void)
 
 	do {
 		seq = read_seqbegin(&xtime_lock);
-
-		now = xtime_cache;
+		now = xtime;
 		mono = wall_to_monotonic;
 	} while (read_seqretry(&xtime_lock, seq));
 
#2 lore raw

[tip:timers/core] time: Remove xtime_cache

Commit-ID:  5335c1c371aa32fcef97c4979f04b065772194ab
Gitweb:     http://git.kernel.org/tip/5335c1c371aa32fcef97c4979f04b065772194ab
Author:     john stultz <[email protected]>
AuthorDate: Fri, 2 Oct 2009 16:24:15 -0700
Committer:  Ingo Molnar <[email protected]>
CommitDate: Sun, 4 Oct 2009 19:31:39 +0200

time: Remove xtime_cache

With the prior logarithmic time accumulation patch, xtime will now always be within one "tick" of the current time, instead of possibly half a second off.

This removes the need for the xtime_cache value, which always stored the time at the last interrupt, so this patch cleans that up removing the xtime_cache related code.

This is a bit simpler, but still could use some wider testing.

Cc John Kacur <[email protected]>
Cc Clark Williams <[email protected]>
Cc Martin Schwidefsky <[email protected]>
Cc Andrew Morton <[email protected]>

LKML-Reference: <[email protected]>

---
 kernel/time.c             |    1 -
 kernel/time/timekeeping.c |   27 ++++-----------------------
 2 files changed, 4 insertions(+), 24 deletions(-)
kernel/time.c +0 -1
index 2e2e469..2ef4fe2 100644
@@ -136,7 +136,6 @@ static inline void warp_clock(void)
 	write_seqlock_irq(&xtime_lock);
 	wall_to_monotonic.tv_sec -= sys_tz.tz_minuteswest * 60;
 	xtime.tv_sec += sys_tz.tz_minuteswest * 60;
-	update_xtime_cache(0);
 	write_sequnlock_irq(&xtime_lock);
 	clock_was_set();
 }
kernel/time/timekeeping.c +4 -23
index 5fdd78e..96b3f0d 100644
@@ -164,13 +164,6 @@ struct timespec raw_time;
 /* flag for if timekeeping is suspended */
 int __read_mostly timekeeping_suspended;
 
-static struct timespec xtime_cache __attribute__ ((aligned (16)));
-void update_xtime_cache(u64 nsec)
-{
-	xtime_cache = xtime;
-	timespec_add_ns(&xtime_cache, nsec);
-}
-
 /* must hold xtime_lock */
 void timekeeping_leap_insert(int leapsecond)
 {
@@ -331,8 +324,6 @@ int do_settimeofday(struct timespec *tv)
 
 	xtime = *tv;
 
-	update_xtime_cache(0);
-
 	timekeeper.ntp_error = 0;
 	ntp_clear();
 
@@ -547,7 +538,6 @@ void __init timekeeping_init(void)
 	}
 	set_normalized_timespec(&wall_to_monotonic,
 				-boot.tv_sec, -boot.tv_nsec);
-	update_xtime_cache(0);
 	total_sleep_time.tv_sec = 0;
 	total_sleep_time.tv_nsec = 0;
 	write_sequnlock_irqrestore(&xtime_lock, flags);
@@ -581,7 +571,6 @@ static int timekeeping_resume(struct sys_device *dev)
 		wall_to_monotonic = timespec_sub(wall_to_monotonic, ts);
 		total_sleep_time = timespec_add_safe(total_sleep_time, ts);
 	}
-	update_xtime_cache(0);
 	/* re-base the last cycle value */
 	timekeeper.clock->cycle_last = timekeeper.clock->read(timekeeper.clock);
 	timekeeper.ntp_error = 0;
@@ -721,7 +710,6 @@ static void timekeeping_adjust(s64 offset)
 				timekeeper.ntp_error_shift;
 }
 
-
 /**
  * logarithmic_accumulation - shifted accumulation of cycles
  *
@@ -765,7 +753,6 @@ static cycle_t logarithmic_accumulation(cycle_t offset, int shift)
 	return offset;
 }
 
-
 /**
  * update_wall_time - Uses the current clocksource to increment the wall time
  *
@@ -775,7 +762,6 @@ void update_wall_time(void)
 {
 	struct clocksource *clock;
 	cycle_t offset;
-	u64 nsecs;
 	int shift = 0, maxshift;
 
 	/* Make sure we're fully resumed: */
@@ -841,9 +827,6 @@ void update_wall_time(void)
 	timekeeper.ntp_error +=	timekeeper.xtime_nsec <<
 				timekeeper.ntp_error_shift;
 
-	nsecs = clocksource_cyc2ns(offset, timekeeper.mult, timekeeper.shift);
-	update_xtime_cache(nsecs);
-
 	/* check to see if there is a new clocksource to use */
 	update_vsyscall(&xtime, timekeeper.clock);
 }
@@ -880,13 +863,13 @@ void monotonic_to_bootbased(struct timespec *ts)
 
 unsigned long get_seconds(void)
 {
-	return xtime_cache.tv_sec;
+	return xtime.tv_sec;
 }
 EXPORT_SYMBOL(get_seconds);
 
 struct timespec __current_kernel_time(void)
 {
-	return xtime_cache;
+	return xtime;
 }
 
 struct timespec current_kernel_time(void)
@@ -896,8 +879,7 @@ struct timespec current_kernel_time(void)
 
 	do {
 		seq = read_seqbegin(&xtime_lock);
-
-		now = xtime_cache;
+		now = xtime;
 	} while (read_seqretry(&xtime_lock, seq));
 
 	return now;
@@ -911,8 +893,7 @@ struct timespec get_monotonic_coarse(void)
 
 	do {
 		seq = read_seqbegin(&xtime_lock);
-
-		now = xtime_cache;
+		now = xtime;
 		mono = wall_to_monotonic;
 	} while (read_seqretry(&xtime_lock, seq));
 
#3 lore raw

[tip:timers/core] time: Remove xtime_cache

In reply to john stultz
Commit-ID:  7bc7d637452383d56ba4368d4336b0dde1bb476d
Gitweb:     http://git.kernel.org/tip/7bc7d637452383d56ba4368d4336b0dde1bb476d
Author:     john stultz <[email protected]>
AuthorDate: Fri, 2 Oct 2009 16:24:15 -0700
Committer:  Ingo Molnar <[email protected]>
CommitDate: Mon, 5 Oct 2009 13:52:02 +0200

time: Remove xtime_cache

With the prior logarithmic time accumulation patch, xtime will now always be within one "tick" of the current time, instead of possibly half a second off.

This removes the need for the xtime_cache value, which always stored the time at the last interrupt, so this patch cleans that up removing the xtime_cache related code.

This is a bit simpler, but still could use some wider testing.

LKML-Reference: <[email protected]>

---
 kernel/time.c             |    1 -
 kernel/time/timekeeping.c |   27 ++++-----------------------
 2 files changed, 4 insertions(+), 24 deletions(-)
kernel/time.c +0 -1
index 2e2e469..2ef4fe2 100644
@@ -136,7 +136,6 @@ static inline void warp_clock(void)
 	write_seqlock_irq(&xtime_lock);
 	wall_to_monotonic.tv_sec -= sys_tz.tz_minuteswest * 60;
 	xtime.tv_sec += sys_tz.tz_minuteswest * 60;
-	update_xtime_cache(0);
 	write_sequnlock_irq(&xtime_lock);
 	clock_was_set();
 }
kernel/time/timekeeping.c +4 -23
index 5fdd78e..96b3f0d 100644
@@ -164,13 +164,6 @@ struct timespec raw_time;
 /* flag for if timekeeping is suspended */
 int __read_mostly timekeeping_suspended;
 
-static struct timespec xtime_cache __attribute__ ((aligned (16)));
-void update_xtime_cache(u64 nsec)
-{
-	xtime_cache = xtime;
-	timespec_add_ns(&xtime_cache, nsec);
-}
-
 /* must hold xtime_lock */
 void timekeeping_leap_insert(int leapsecond)
 {
@@ -331,8 +324,6 @@ int do_settimeofday(struct timespec *tv)
 
 	xtime = *tv;
 
-	update_xtime_cache(0);
-
 	timekeeper.ntp_error = 0;
 	ntp_clear();
 
@@ -547,7 +538,6 @@ void __init timekeeping_init(void)
 	}
 	set_normalized_timespec(&wall_to_monotonic,
 				-boot.tv_sec, -boot.tv_nsec);
-	update_xtime_cache(0);
 	total_sleep_time.tv_sec = 0;
 	total_sleep_time.tv_nsec = 0;
 	write_sequnlock_irqrestore(&xtime_lock, flags);
@@ -581,7 +571,6 @@ static int timekeeping_resume(struct sys_device *dev)
 		wall_to_monotonic = timespec_sub(wall_to_monotonic, ts);
 		total_sleep_time = timespec_add_safe(total_sleep_time, ts);
 	}
-	update_xtime_cache(0);
 	/* re-base the last cycle value */
 	timekeeper.clock->cycle_last = timekeeper.clock->read(timekeeper.clock);
 	timekeeper.ntp_error = 0;
@@ -721,7 +710,6 @@ static void timekeeping_adjust(s64 offset)
 				timekeeper.ntp_error_shift;
 }
 
-
 /**
  * logarithmic_accumulation - shifted accumulation of cycles
  *
@@ -765,7 +753,6 @@ static cycle_t logarithmic_accumulation(cycle_t offset, int shift)
 	return offset;
 }
 
-
 /**
  * update_wall_time - Uses the current clocksource to increment the wall time
  *
@@ -775,7 +762,6 @@ void update_wall_time(void)
 {
 	struct clocksource *clock;
 	cycle_t offset;
-	u64 nsecs;
 	int shift = 0, maxshift;
 
 	/* Make sure we're fully resumed: */
@@ -841,9 +827,6 @@ void update_wall_time(void)
 	timekeeper.ntp_error +=	timekeeper.xtime_nsec <<
 				timekeeper.ntp_error_shift;
 
-	nsecs = clocksource_cyc2ns(offset, timekeeper.mult, timekeeper.shift);
-	update_xtime_cache(nsecs);
-
 	/* check to see if there is a new clocksource to use */
 	update_vsyscall(&xtime, timekeeper.clock);
 }
@@ -880,13 +863,13 @@ void monotonic_to_bootbased(struct timespec *ts)
 
 unsigned long get_seconds(void)
 {
-	return xtime_cache.tv_sec;
+	return xtime.tv_sec;
 }
 EXPORT_SYMBOL(get_seconds);
 
 struct timespec __current_kernel_time(void)
 {
-	return xtime_cache;
+	return xtime;
 }
 
 struct timespec current_kernel_time(void)
@@ -896,8 +879,7 @@ struct timespec current_kernel_time(void)
 
 	do {
 		seq = read_seqbegin(&xtime_lock);
-
-		now = xtime_cache;
+		now = xtime;
 	} while (read_seqretry(&xtime_lock, seq));
 
 	return now;
@@ -911,8 +893,7 @@ struct timespec get_monotonic_coarse(void)
 
 	do {
 		seq = read_seqbegin(&xtime_lock);
-
-		now = xtime_cache;
+		now = xtime;
 		mono = wall_to_monotonic;
 	} while (read_seqretry(&xtime_lock, seq));
 
Acked-by Thomas Gleixner Reviewed-by on v1 2/2
#4 lore raw

Re: [PATCH 2/2] time: remove xtime_cache

In reply to john stultz

@John Stultz
I also backported this patch to 2.6.31.2-rt13, could you please look it over and see if it looks okay to you?

@Thomas
Same as the previous patch, please consider queuing this for -rt14 and we can drop it in the future because John Stultz submitted it upstream.

Thanks

Quoted 1 line

From 868ee3f7346a90ae3b529ac24996f059cc322a82 Mon Sep 17 00:00:00 2001

From: tip-bot for john stultz <[email protected]>
Date: Mon, 5 Oct 2009 11:54:53 +0000
Subject: [PATCH] time: Remove xtime_cache

Commit-ID:  7bc7d637452383d56ba4368d4336b0dde1bb476d
Gitweb:     http://git.kernel.org/tip/7bc7d637452383d56ba4368d4336b0dde1bb476d
Author:     john stultz <[email protected]>
AuthorDate: Fri, 2 Oct 2009 16:24:15 -0700
Committer:  Ingo Molnar <[email protected]>
CommitDate: Mon, 5 Oct 2009 13:52:02 +0200

time: Remove xtime_cache

With the prior logarithmic time accumulation patch, xtime will now always be within one "tick" of the current time, instead of possibly half a second off.

This removes the need for the xtime_cache value, which always stored the time at the last interrupt, so this patch cleans that up removing the xtime_cache related code.

This is a bit simpler, but still could use some wider testing.

LKML-Reference: <[email protected]>

---
 kernel/time.c             |    1 -
 kernel/time/timekeeping.c |   20 ++------------------
 2 files changed, 2 insertions(+), 19 deletions(-)
kernel/time.c +0 -1
index 35d1aaa..01944b5 100644
@@ -136,7 +136,6 @@ static inline void warp_clock(void)
 	write_atomic_seqlock_irq(&xtime_lock);
 	wall_to_monotonic.tv_sec -= sys_tz.tz_minuteswest * 60;
 	xtime.tv_sec += sys_tz.tz_minuteswest * 60;
-	update_xtime_cache(0);
 	write_atomic_sequnlock_irq(&xtime_lock);
 	clock_was_set();
 }
kernel/time/timekeeping.c +0 -15
index 4630874..4a0920d 100644
@@ -48,16 +48,8 @@ static unsigned long total_sleep_time;		/* seconds */
 /* flag for if timekeeping is suspended */
 int __read_mostly timekeeping_suspended;
 
-static struct timespec xtime_cache __attribute__ ((aligned (16)));
-void update_xtime_cache(u64 nsec)
-{
-	xtime_cache = xtime;
-	timespec_add_ns(&xtime_cache, nsec);
-}
-
 struct clocksource *clock;
 
-
 #ifdef CONFIG_GENERIC_TIME
 /**
  * clocksource_forward_now - update clock to the current time
@@ -233,7 +225,6 @@ int do_settimeofday(struct timespec *tv)
 
 	xtime = *tv;
 
-	update_xtime_cache(0);
 
 	clock->error = 0;
 	ntp_clear();
@@ -435,7 +426,6 @@ void __init timekeeping_init(void)
 	xtime.tv_nsec = 0;
 	set_normalized_timespec(&wall_to_monotonic,
 		-xtime.tv_sec, -xtime.tv_nsec);
-	update_xtime_cache(0);
 	total_sleep_time = 0;
 	write_atomic_sequnlock_irqrestore(&xtime_lock, flags);
 }
@@ -467,7 +457,6 @@ static int timekeeping_resume(struct sys_device *dev)
 		wall_to_monotonic.tv_sec -= sleep_length;
 		total_sleep_time += sleep_length;
 	}
-	update_xtime_cache(0);
 	/* re-base the last cycle value */
 	clock->cycle_last = 0;
 	clock->cycle_last = clocksource_read(clock);
@@ -608,7 +597,6 @@ static void clocksource_adjust(s64 offset)
 			(NTP_SCALE_SHIFT - clock->shift);
 }
 
-
 /**
  * logarithmic_accumulation - shifted accumulation of cycles
  *
@@ -652,7 +640,6 @@ static cycle_t logarithmic_accumulation(cycle_t offset, int shift)
 	return offset;
 }
 
-
 /**
  * update_wall_time - Uses the current clocksource to increment the wall time
  *
@@ -661,7 +648,6 @@ static cycle_t logarithmic_accumulation(cycle_t offset, int shift)
 void update_wall_time(void)
 {
 	cycle_t offset;
-	u64 nsecs;
 	int shift = 0, maxshift;
 
 	/* Make sure we're fully resumed: */
@@ -725,8 +711,6 @@ void update_wall_time(void)
 	clock->xtime_nsec -= (s64)xtime.tv_nsec << clock->shift;
 	clock->error += clock->xtime_nsec << (NTP_SCALE_SHIFT - clock->shift);
 
-	update_xtime_cache(cyc2ns(clock, offset));
#5 lore raw
In reply to john stultz
Quoted 164 lines · john stultz

Accumulating one tick at a time works well unless we're using NOHZ. Then it can be an issue, since we may have to run through the loop a few thousand times, which can increase timer interrupt caused latency.

The current solution was to accumulate in half-second intervals with NOHZ. This kept the number of loops down, however it did slightly change how we make NTP adjustments. While not an issue with NTPd users, as NTPd makes adjustments over a longer period of time, other adjtimex() users have noticed the half-second granularity with which we can apply frequency changes to the clock.

For instance, if a application tries to apply a 100ppm frequency correction for 20ms to correct a 2us offset, with NOHZ they either get no correction, or a 50us correction.

Now, there will always be some granularity error for applying frequency corrections. However with users sensitive to this error have seen a 50-500x increase with NOHZ compared to running without NOHZ.

So I figured I'd try another approach then just simply increasing the interval. My approach is to consume the time interval logarithmically. This reduces the number of times through the loop needed keeping latency down, while still preserving the original granularity error for adjtimex() changes.

Further, this change allows us to remove the xtime_cache code (patch to follow), as xtime is always within one tick of the current time, instead of the half-second updates it saw before.

An earlier version of this patch has been shipping to x86 users in the RedHat MRG releases for awhile without issue, but I've reworked this version to be even more careful about avoiding possible overflows if the shift value gets too large.

Since this is not the most trivial code, and its slightly different then whats been tested for awhile, it would be good to get this into some trees for testing. Be it -tip or -mm, either would work. If there's no problems it could be a 2.6.33 or 2.6.34 item.

Any comments or feedback would be appreciated!

include/linux/timex.h +0 -4
index e6967d1..0c0ef7d 100644
@@ -261,11 +261,7 @@ static inline int ntp_synced(void)
 
 #define NTP_SCALE_SHIFT		32
 
-#ifdef CONFIG_NO_HZ
-#define NTP_INTERVAL_FREQ  (2)
-#else
 #define NTP_INTERVAL_FREQ  (HZ)
-#endif
 #define NTP_INTERVAL_LENGTH (NSEC_PER_SEC/NTP_INTERVAL_FREQ)
 
 /* Returns how long ticks are at present, in ns / 2^NTP_SCALE_SHIFT. */
kernel/time/timekeeping.c +58 -20
index fb0f46f..4cc5656 100644
@@ -721,6 +721,51 @@ static void timekeeping_adjust(s64 offset)
 				timekeeper.ntp_error_shift;
 }
 
+
+/**
+ * logarithmic_accumulation - shifted accumulation of cycles
+ *
+ * This functions accumulates a shifted interval of cycles into 
+ * into a shifted interval nanoseconds. Allows for O(log) accumulation
+ * loop.
+ * 
+ * Returns the unconsumed cycles.
+ */
+static cycle_t logarithmic_accumulation(cycle_t offset, int shift)
+{
+	u64 nsecps = (u64)NSEC_PER_SEC << timekeeper.shift;
+
+	/* If the offset is smaller then a shifted interval, do nothing */
+	if (offset < timekeeper.cycle_interval<<shift)
+		return offset;
+
+	/* accumulate one shifted interval */
+	offset -= timekeeper.cycle_interval << shift;
+	timekeeper.clock->cycle_last += timekeeper.cycle_interval << shift;
+	
+	timekeeper.xtime_nsec += timekeeper.xtime_interval << shift;
+	while (timekeeper.xtime_nsec >= nsecps) {
+		timekeeper.xtime_nsec -= nsecps;
+		xtime.tv_sec++;
+		second_overflow();
+	}
+	
+	/* accumulate into raw time */
+	raw_time.tv_nsec += timekeeper.raw_interval << shift;;
+	while (raw_time.tv_nsec >= NSEC_PER_SEC) {
+		raw_time.tv_nsec -= NSEC_PER_SEC;
+		raw_time.tv_sec++;
+	}
+
+	/* accumulate error between NTP and clock interval */
+	timekeeper.ntp_error += tick_length << shift;
+	timekeeper.ntp_error -= timekeeper.xtime_interval <<
+				(timekeeper.ntp_error_shift + shift);
+
+	return offset;
+}
+
+
 /**
  * update_wall_time - Uses the current clocksource to increment the wall time
  *
@@ -731,6 +776,7 @@ void update_wall_time(void)
 	struct clocksource *clock;
 	cycle_t offset;
 	u64 nsecs;
+	int shift = 0, maxshift;
 
 	/* Make sure we're fully resumed: */
 	if (unlikely(timekeeping_suspended))
@@ -744,33 +790,22 @@ void update_wall_time(void)
 #endif
 	timekeeper.xtime_nsec = (s64)xtime.tv_nsec << timekeeper.shift;
 
-	/* normally this loop will run just once, however in the
-	 * case of lost or late ticks, it will accumulate correctly.
+	/*
+	 * With NO_HZ we may have to accumulate many cycle_intervals
+	 * (think "ticks") worth of time at once. To do this efficiently,
+	 * we calculate the largest doubling multiple of cycle_intervals
+	 * that is smaller then the offset. We then accumulate that 
+	 * chunk in one go, and then try to consume the next smaller
+	 * doubled multiple.
 	 */
+	shift = ilog2(offset) - ilog2(timekeeper.cycle_interval);
+	shift = max(0, shift);
+	/* Bound shift to one less then what overflows tick_length */
+	maxshift = (8*sizeof(tick_length) - (ilog2(tick_length)+1)) - 1;
+	shift = min(shift, maxshift);	
 	while (offset >= timekeeper.cycle_interval) {
-		u64 nsecps = (u64)NSEC_PER_SEC << timekeeper.shift;
-
-		/* accumulate one interval */
-		offset -= timekeeper.cycle_interval;
-		clock->cycle_last += timekeeper.cycle_interval;
-
-		timekeeper.xtime_nsec += timekeeper.xtime_interval;
-		if (timekeeper.xtime_nsec >= nsecps) {
-			timekeeper.xtime_nsec -= nsecps;
-			xtime.tv_sec++;
-			second_overflow();
-		}
-
-		raw_time.tv_nsec += timekeeper.raw_interval;
-		if (raw_time.tv_nsec >= NSEC_PER_SEC) {
-			raw_time.tv_nsec -= NSEC_PER_SEC;
-			raw_time.tv_sec++;
-		}

kernel/time/timekeeping.c void update_wall_time(void) · line 811

Quoted 10 lines
kernel/time/timekeeping.c +2 -5
-
-		/* accumulate error between NTP and clock interval */
-		timekeeper.ntp_error += tick_length;
-		timekeeper.ntp_error -= timekeeper.xtime_interval <<
-					timekeeper.ntp_error_shift;
+		offset = logarithmic_accumulation(offset, shift);
+		shift--;
 	}
 
 	/* correct the clock when NTP error is too big */

There are several (6) trailing whitespace errors that checkpatch exposes, but other than that:

#6 lore raw
Quoted 174 lines · John Kacur
Quoted 170 lines · john stultz

Accumulating one tick at a time works well unless we're using NOHZ. Then it can be an issue, since we may have to run through the loop a few thousand times, which can increase timer interrupt caused latency.

The current solution was to accumulate in half-second intervals with NOHZ. This kept the number of loops down, however it did slightly change how we make NTP adjustments. While not an issue with NTPd users, as NTPd makes adjustments over a longer period of time, other adjtimex() users have noticed the half-second granularity with which we can apply frequency changes to the clock.

For instance, if a application tries to apply a 100ppm frequency correction for 20ms to correct a 2us offset, with NOHZ they either get no correction, or a 50us correction.

Now, there will always be some granularity error for applying frequency corrections. However with users sensitive to this error have seen a 50-500x increase with NOHZ compared to running without NOHZ.

So I figured I'd try another approach then just simply increasing the interval. My approach is to consume the time interval logarithmically. This reduces the number of times through the loop needed keeping latency down, while still preserving the original granularity error for adjtimex() changes.

Further, this change allows us to remove the xtime_cache code (patch to follow), as xtime is always within one tick of the current time, instead of the half-second updates it saw before.

An earlier version of this patch has been shipping to x86 users in the RedHat MRG releases for awhile without issue, but I've reworked this version to be even more careful about avoiding possible overflows if the shift value gets too large.

Since this is not the most trivial code, and its slightly different then whats been tested for awhile, it would be good to get this into some trees for testing. Be it -tip or -mm, either would work. If there's no problems it could be a 2.6.33 or 2.6.34 item.

Any comments or feedback would be appreciated!

include/linux/timex.h +0 -4
index e6967d1..0c0ef7d 100644
@@ -261,11 +261,7 @@ static inline int ntp_synced(void)
 
 #define NTP_SCALE_SHIFT		32
 
-#ifdef CONFIG_NO_HZ
-#define NTP_INTERVAL_FREQ  (2)
-#else
 #define NTP_INTERVAL_FREQ  (HZ)
-#endif
 #define NTP_INTERVAL_LENGTH (NSEC_PER_SEC/NTP_INTERVAL_FREQ)
 
 /* Returns how long ticks are at present, in ns / 2^NTP_SCALE_SHIFT. */
kernel/time/timekeeping.c +60 -25
index fb0f46f..4cc5656 100644
@@ -721,6 +721,51 @@ static void timekeeping_adjust(s64 offset)
 				timekeeper.ntp_error_shift;
 }
 
+
+/**
+ * logarithmic_accumulation - shifted accumulation of cycles
+ *
+ * This functions accumulates a shifted interval of cycles into 
+ * into a shifted interval nanoseconds. Allows for O(log) accumulation
+ * loop.
+ * 
+ * Returns the unconsumed cycles.
+ */
+static cycle_t logarithmic_accumulation(cycle_t offset, int shift)
+{
+	u64 nsecps = (u64)NSEC_PER_SEC << timekeeper.shift;
+
+	/* If the offset is smaller then a shifted interval, do nothing */
+	if (offset < timekeeper.cycle_interval<<shift)
+		return offset;
+
+	/* accumulate one shifted interval */
+	offset -= timekeeper.cycle_interval << shift;
+	timekeeper.clock->cycle_last += timekeeper.cycle_interval << shift;
+	
+	timekeeper.xtime_nsec += timekeeper.xtime_interval << shift;
+	while (timekeeper.xtime_nsec >= nsecps) {
+		timekeeper.xtime_nsec -= nsecps;
+		xtime.tv_sec++;
+		second_overflow();
+	}
+	
+	/* accumulate into raw time */
+	raw_time.tv_nsec += timekeeper.raw_interval << shift;;
+	while (raw_time.tv_nsec >= NSEC_PER_SEC) {
+		raw_time.tv_nsec -= NSEC_PER_SEC;
+		raw_time.tv_sec++;
+	}
+
+	/* accumulate error between NTP and clock interval */
+	timekeeper.ntp_error += tick_length << shift;
+	timekeeper.ntp_error -= timekeeper.xtime_interval <<
+				(timekeeper.ntp_error_shift + shift);
+
+	return offset;
+}
+
+
 /**
  * update_wall_time - Uses the current clocksource to increment the wall time
  *
@@ -731,6 +776,7 @@ void update_wall_time(void)
 	struct clocksource *clock;
 	cycle_t offset;
 	u64 nsecs;
+	int shift = 0, maxshift;
 
 	/* Make sure we're fully resumed: */
 	if (unlikely(timekeeping_suspended))
@@ -744,33 +790,22 @@ void update_wall_time(void)
 #endif
 	timekeeper.xtime_nsec = (s64)xtime.tv_nsec << timekeeper.shift;
 
-	/* normally this loop will run just once, however in the
-	 * case of lost or late ticks, it will accumulate correctly.
+	/*
+	 * With NO_HZ we may have to accumulate many cycle_intervals
+	 * (think "ticks") worth of time at once. To do this efficiently,
+	 * we calculate the largest doubling multiple of cycle_intervals
+	 * that is smaller then the offset. We then accumulate that 
+	 * chunk in one go, and then try to consume the next smaller
+	 * doubled multiple.
 	 */
+	shift = ilog2(offset) - ilog2(timekeeper.cycle_interval);
+	shift = max(0, shift);
+	/* Bound shift to one less then what overflows tick_length */
+	maxshift = (8*sizeof(tick_length) - (ilog2(tick_length)+1)) - 1;
+	shift = min(shift, maxshift);	
 	while (offset >= timekeeper.cycle_interval) {
-		u64 nsecps = (u64)NSEC_PER_SEC << timekeeper.shift;
-
-		/* accumulate one interval */
-		offset -= timekeeper.cycle_interval;
-		clock->cycle_last += timekeeper.cycle_interval;
-
-		timekeeper.xtime_nsec += timekeeper.xtime_interval;
-		if (timekeeper.xtime_nsec >= nsecps) {
-			timekeeper.xtime_nsec -= nsecps;
-			xtime.tv_sec++;
-			second_overflow();
-		}
-
-		raw_time.tv_nsec += timekeeper.raw_interval;
-		if (raw_time.tv_nsec >= NSEC_PER_SEC) {
-			raw_time.tv_nsec -= NSEC_PER_SEC;
-			raw_time.tv_sec++;
-		}
-
-		/* accumulate error between NTP and clock interval */
-		timekeeper.ntp_error += tick_length;
-		timekeeper.ntp_error -= timekeeper.xtime_interval <<
-					timekeeper.ntp_error_shift;
+		offset = logarithmic_accumulation(offset, shift);
+		shift--;
 	}
 
Quoted 7 lines

kernel/time/timekeeping.c void update_wall_time(void) · line 811

Quoted 4 lines
kernel/time/timekeeping.c +0 -0
 	/* correct the clock when NTP error is too big */

There are several (6) trailing whitespace errors that checkpatch exposes, but other than that:

Yep, i fixed those already. (also the few inconsistent comment capitalizations)

The two patches held up fine in -tip testing so far.

Quoted 1 line

Thanks - i changed that to Reviewed-by (SoB is for being part of the patch-flow) and added it to the two commits.

Ingo

Acked-by Thomas Gleixner Reviewed-by
#7 lore raw

@John Stultz
I backported your patch to 2.6.31.2-rt13, could you please look it over and see if it looks okay to you?

@Thomas
Could you please consider queuing this up for -rt14.
Since John submitted it upstream, we will be able to drop it again in the future.

Thanks

Quoted 1 line

From 8090f669e58901c1b0c5e8bac4160eaaf7990f4d Mon Sep 17 00:00:00 2001

From: tip-bot for john stultz <[email protected]>
Date: Mon, 5 Oct 2009 11:54:38 +0000
Subject: [PATCH] time: Implement logarithmic time accumulation

Commit-ID:  a092ff0f90cae22b2ac8028ecd2c6f6c1a9e4601
Gitweb:     http://git.kernel.org/tip/a092ff0f90cae22b2ac8028ecd2c6f6c1a9e4601
Author:     john stultz <[email protected]>
AuthorDate: Fri, 2 Oct 2009 16:17:53 -0700
Committer:  Ingo Molnar <[email protected]>
CommitDate: Mon, 5 Oct 2009 13:51:48 +0200

time: Implement logarithmic time accumulation

Accumulating one tick at a time works well unless we're using NOHZ. Then it can be an issue, since we may have to run through the loop a few thousand times, which can increase timer interrupt caused latency.

The current solution was to accumulate in half-second intervals with NOHZ. This kept the number of loops down, however it did slightly change how we make NTP adjustments. While not an issue with NTPd users, as NTPd makes adjustments over a longer period of time, other adjtimex() users have noticed the half-second granularity with which we can apply frequency changes to the clock.

For instance, if a application tries to apply a 100ppm frequency correction for 20ms to correct a 2us offset, with NOHZ they either get no correction, or a 50us correction.

Now, there will always be some granularity error for applying frequency corrections. However with users sensitive to this error have seen a 50-500x increase with NOHZ compared to running without NOHZ.

So I figured I'd try another approach then just simply increasing the interval. My approach is to consume the time interval logarithmically. This reduces the number of times through the loop needed keeping latency down, while still preserving the original granularity error for adjtimex() changes.

Further, this change allows us to remove the xtime_cache code (patch to follow), as xtime is always within one tick of the current time, instead of the half-second updates it saw before.

An earlier version of this patch has been shipping to x86 users in the RedHat MRG releases for awhile without issue, but I've reworked this version to be even more careful about avoiding possible overflows if the shift value gets too large.

LKML-Reference: <[email protected]>

---
 include/linux/timex.h     |    4 --
 kernel/time/timekeeping.c |   83 +++++++++++++++++++++++++++++++++------------
 2 files changed, 61 insertions(+), 26 deletions(-)
include/linux/timex.h +0 -4
index e6967d1..0c0ef7d 100644
@@ -261,11 +261,7 @@ static inline int ntp_synced(void)
 
 #define NTP_SCALE_SHIFT		32
 
-#ifdef CONFIG_NO_HZ
-#define NTP_INTERVAL_FREQ  (2)
-#else
 #define NTP_INTERVAL_FREQ  (HZ)
-#endif
 #define NTP_INTERVAL_LENGTH (NSEC_PER_SEC/NTP_INTERVAL_FREQ)
 
 /* Returns how long ticks are at present, in ns / 2^NTP_SCALE_SHIFT. */
kernel/time/timekeeping.c +59 -18

94 lines not on this page · raw message

#8 lore raw
In reply to John Kacur
Quoted 71 lines · On Mon, 5 Oct 2009 12:43:37 +0200 (CEST) John Kacur wrote:
Quoted 67 lines · john stultz

Accumulating one tick at a time works well unless we're using NOHZ. Then it can be an issue, since we may have to run through the loop a few thousand times, which can increase timer interrupt caused latency.

The current solution was to accumulate in half-second intervals with NOHZ. This kept the number of loops down, however it did slightly change how we make NTP adjustments. While not an issue with NTPd users, as NTPd makes adjustments over a longer period of time, other adjtimex() users have noticed the half-second granularity with which we can apply frequency changes to the clock.

For instance, if a application tries to apply a 100ppm frequency correction for 20ms to correct a 2us offset, with NOHZ they either get no correction, or a 50us correction.

Now, there will always be some granularity error for applying frequency corrections. However with users sensitive to this error have seen a 50-500x increase with NOHZ compared to running without NOHZ.

So I figured I'd try another approach then just simply increasing the interval. My approach is to consume the time interval logarithmically. This reduces the number of times through the loop needed keeping latency down, while still preserving the original granularity error for adjtimex() changes.

Further, this change allows us to remove the xtime_cache code (patch to follow), as xtime is always within one tick of the current time, instead of the half-second updates it saw before.

An earlier version of this patch has been shipping to x86 users in the RedHat MRG releases for awhile without issue, but I've reworked this version to be even more careful about avoiding possible overflows if the shift value gets too large.

Since this is not the most trivial code, and its slightly different then whats been tested for awhile, it would be good to get this into some trees for testing. Be it -tip or -mm, either would work. If there's no problems it could be a 2.6.33 or 2.6.34 item.

Any comments or feedback would be appreciated!

include/linux/timex.h +0 -4
index e6967d1..0c0ef7d 100644
@@ -261,11 +261,7 @@ static inline int ntp_synced(void)
 
 #define NTP_SCALE_SHIFT		32
 
-#ifdef CONFIG_NO_HZ
-#define NTP_INTERVAL_FREQ  (2)
-#else
 #define NTP_INTERVAL_FREQ  (HZ)
-#endif
 #define NTP_INTERVAL_LENGTH (NSEC_PER_SEC/NTP_INTERVAL_FREQ)
 
 /* Returns how long ticks are at present, in ns / 2^NTP_SCALE_SHIFT. */
kernel/time/timekeeping.c +0 -0
index fb0f46f..4cc5656 100644
@@ -721,6 +721,51 @@ static void timekeeping_adjust(s64 offset)
 				timekeeper.ntp_error_shift;
 }
 
Quoted 2 lines

kernel/time/timekeeping.c static void timekeeping_adjust(s64 offset) · line 725

Quoted 2 lines
kernel/time/timekeeping.c +2 -0
+
+/**

"/**" means "beginning of kernel-doc", so those function parameters need to be described here also...

Quoted 101 lines
Quoted 101 lines
kernel/time/timekeeping.c +58 -25
+ * logarithmic_accumulation - shifted accumulation of cycles
+ *
+ * This functions accumulates a shifted interval of cycles into 
+ * into a shifted interval nanoseconds. Allows for O(log) accumulation
+ * loop.
+ * 
+ * Returns the unconsumed cycles.
+ */
+static cycle_t logarithmic_accumulation(cycle_t offset, int shift)
+{
+	u64 nsecps = (u64)NSEC_PER_SEC << timekeeper.shift;
+
+	/* If the offset is smaller then a shifted interval, do nothing */
+	if (offset < timekeeper.cycle_interval<<shift)
+		return offset;
+
+	/* accumulate one shifted interval */
+	offset -= timekeeper.cycle_interval << shift;
+	timekeeper.clock->cycle_last += timekeeper.cycle_interval << shift;
+	
+	timekeeper.xtime_nsec += timekeeper.xtime_interval << shift;
+	while (timekeeper.xtime_nsec >= nsecps) {
+		timekeeper.xtime_nsec -= nsecps;
+		xtime.tv_sec++;
+		second_overflow();
+	}
+	
+	/* accumulate into raw time */
+	raw_time.tv_nsec += timekeeper.raw_interval << shift;;
+	while (raw_time.tv_nsec >= NSEC_PER_SEC) {
+		raw_time.tv_nsec -= NSEC_PER_SEC;
+		raw_time.tv_sec++;
+	}
+
+	/* accumulate error between NTP and clock interval */
+	timekeeper.ntp_error += tick_length << shift;
+	timekeeper.ntp_error -= timekeeper.xtime_interval <<
+				(timekeeper.ntp_error_shift + shift);
+
+	return offset;
+}
+
+
 /**
  * update_wall_time - Uses the current clocksource to increment the wall time
  *
@@ -731,6 +776,7 @@ void update_wall_time(void)
 	struct clocksource *clock;
 	cycle_t offset;
 	u64 nsecs;
+	int shift = 0, maxshift;
 
 	/* Make sure we're fully resumed: */
 	if (unlikely(timekeeping_suspended))
@@ -744,33 +790,22 @@ void update_wall_time(void)
 #endif
 	timekeeper.xtime_nsec = (s64)xtime.tv_nsec << timekeeper.shift;
 
-	/* normally this loop will run just once, however in the
-	 * case of lost or late ticks, it will accumulate correctly.
+	/*
+	 * With NO_HZ we may have to accumulate many cycle_intervals
+	 * (think "ticks") worth of time at once. To do this efficiently,
+	 * we calculate the largest doubling multiple of cycle_intervals
+	 * that is smaller then the offset. We then accumulate that 
+	 * chunk in one go, and then try to consume the next smaller
+	 * doubled multiple.
 	 */
+	shift = ilog2(offset) - ilog2(timekeeper.cycle_interval);
+	shift = max(0, shift);
+	/* Bound shift to one less then what overflows tick_length */
+	maxshift = (8*sizeof(tick_length) - (ilog2(tick_length)+1)) - 1;
+	shift = min(shift, maxshift);	
 	while (offset >= timekeeper.cycle_interval) {
-		u64 nsecps = (u64)NSEC_PER_SEC << timekeeper.shift;
-
-		/* accumulate one interval */
-		offset -= timekeeper.cycle_interval;
-		clock->cycle_last += timekeeper.cycle_interval;
-
-		timekeeper.xtime_nsec += timekeeper.xtime_interval;
-		if (timekeeper.xtime_nsec >= nsecps) {
-			timekeeper.xtime_nsec -= nsecps;
-			xtime.tv_sec++;
-			second_overflow();
-		}
-
-		raw_time.tv_nsec += timekeeper.raw_interval;
-		if (raw_time.tv_nsec >= NSEC_PER_SEC) {
-			raw_time.tv_nsec -= NSEC_PER_SEC;
-			raw_time.tv_sec++;
-		}
-
-		/* accumulate error between NTP and clock interval */
-		timekeeper.ntp_error += tick_length;
-		timekeeper.ntp_error -= timekeeper.xtime_interval <<
-					timekeeper.ntp_error_shift;
+		offset = logarithmic_accumulation(offset, shift);
+		shift--;
 	}
 
Quoted 8 lines

kernel/time/timekeeping.c void update_wall_time(void) · line 811

Quoted 4 lines
kernel/time/timekeeping.c +0 -0
 	/* correct the clock when NTP error is too big */

There are several (6) trailing whitespace errors that checkpatch exposes, but other than that:

---
~Randy

#9 lore raw

[tip:timers/core] time: Implement logarithmic time accumulation

In reply to john stultz
Commit-ID:  8a45af8eb809a0d3512877296bd128e73fcee379
Gitweb:     http://git.kernel.org/tip/8a45af8eb809a0d3512877296bd128e73fcee379
Author:     john stultz <[email protected]>
AuthorDate: Fri, 2 Oct 2009 16:17:53 -0700
Committer:  Ingo Molnar <[email protected]>
CommitDate: Sun, 4 Oct 2009 19:31:39 +0200

time: Implement logarithmic time accumulation

Accumulating one tick at a time works well unless we're using NOHZ. Then it can be an issue, since we may have to run through the loop a few thousand times, which can increase timer interrupt caused latency.

The current solution was to accumulate in half-second intervals with NOHZ. This kept the number of loops down, however it did slightly change how we make NTP adjustments. While not an issue with NTPd users, as NTPd makes adjustments over a longer period of time, other adjtimex() users have noticed the half-second granularity with which we can apply frequency changes to the clock.

For instance, if a application tries to apply a 100ppm frequency correction for 20ms to correct a 2us offset, with NOHZ they either get no correction, or a 50us correction.

Now, there will always be some granularity error for applying frequency corrections. However with users sensitive to this error have seen a 50-500x increase with NOHZ compared to running without NOHZ.

So I figured I'd try another approach then just simply increasing the interval. My approach is to consume the time interval logarithmically. This reduces the number of times through the loop needed keeping latency down, while still preserving the original granularity error for adjtimex() changes.

Further, this change allows us to remove the xtime_cache code (patch to follow), as xtime is always within one tick of the current time, instead of the half-second updates it saw before.

An earlier version of this patch has been shipping to x86 users in the RedHat MRG releases for awhile without issue, but I've reworked this version to be even more careful about avoiding possible overflows if the shift value gets too large.

Cc John Kacur <[email protected]>
Cc Clark Williams <[email protected]>
Cc Martin Schwidefsky <[email protected]>
Cc Andrew Morton <[email protected]>

LKML-Reference: <[email protected]>

---
 include/linux/timex.h     |    4 --
 kernel/time/timekeeping.c |   85 +++++++++++++++++++++++++++++++-------------
 2 files changed, 60 insertions(+), 29 deletions(-)
include/linux/timex.h +0 -4
index e6967d1..0c0ef7d 100644
@@ -261,11 +261,7 @@ static inline int ntp_synced(void)
 
 #define NTP_SCALE_SHIFT		32
 
-#ifdef CONFIG_NO_HZ
-#define NTP_INTERVAL_FREQ  (2)
-#else
 #define NTP_INTERVAL_FREQ  (HZ)
-#endif
 #define NTP_INTERVAL_LENGTH (NSEC_PER_SEC/NTP_INTERVAL_FREQ)
 
 /* Returns how long ticks are at present, in ns / 2^NTP_SCALE_SHIFT. */
kernel/time/timekeeping.c +60 -25

105 lines not on this page · raw message

#10 lore raw

[tip:timers/core] time: Implement logarithmic time accumulation

In reply to john stultz
Commit-ID:  a092ff0f90cae22b2ac8028ecd2c6f6c1a9e4601
Gitweb:     http://git.kernel.org/tip/a092ff0f90cae22b2ac8028ecd2c6f6c1a9e4601
Author:     john stultz <[email protected]>
AuthorDate: Fri, 2 Oct 2009 16:17:53 -0700
Committer:  Ingo Molnar <[email protected]>
CommitDate: Mon, 5 Oct 2009 13:51:48 +0200

time: Implement logarithmic time accumulation

Accumulating one tick at a time works well unless we're using NOHZ. Then it can be an issue, since we may have to run through the loop a few thousand times, which can increase timer interrupt caused latency.

The current solution was to accumulate in half-second intervals with NOHZ. This kept the number of loops down, however it did slightly change how we make NTP adjustments. While not an issue with NTPd users, as NTPd makes adjustments over a longer period of time, other adjtimex() users have noticed the half-second granularity with which we can apply frequency changes to the clock.

For instance, if a application tries to apply a 100ppm frequency correction for 20ms to correct a 2us offset, with NOHZ they either get no correction, or a 50us correction.

Now, there will always be some granularity error for applying frequency corrections. However with users sensitive to this error have seen a 50-500x increase with NOHZ compared to running without NOHZ.

So I figured I'd try another approach then just simply increasing the interval. My approach is to consume the time interval logarithmically. This reduces the number of times through the loop needed keeping latency down, while still preserving the original granularity error for adjtimex() changes.

Further, this change allows us to remove the xtime_cache code (patch to follow), as xtime is always within one tick of the current time, instead of the half-second updates it saw before.

An earlier version of this patch has been shipping to x86 users in the RedHat MRG releases for awhile without issue, but I've reworked this version to be even more careful about avoiding possible overflows if the shift value gets too large.

LKML-Reference: <[email protected]>

---
 include/linux/timex.h     |    4 --
 kernel/time/timekeeping.c |   85 +++++++++++++++++++++++++++++++-------------
 2 files changed, 60 insertions(+), 29 deletions(-)
include/linux/timex.h +0 -4
index e6967d1..0c0ef7d 100644
@@ -261,11 +261,7 @@ static inline int ntp_synced(void)
 
 #define NTP_SCALE_SHIFT		32
 
-#ifdef CONFIG_NO_HZ
-#define NTP_INTERVAL_FREQ  (2)
-#else
 #define NTP_INTERVAL_FREQ  (HZ)
-#endif
 #define NTP_INTERVAL_LENGTH (NSEC_PER_SEC/NTP_INTERVAL_FREQ)
 
 /* Returns how long ticks are at present, in ns / 2^NTP_SCALE_SHIFT. */
kernel/time/timekeeping.c +60 -25

105 lines not on this page · raw message