drm/i915: don't warn if backlight unexpectedly enabled
Subsystems (2)
PATCH 1/1 drm/i915: don't warn if backlight unexpectedly enabled
BIOS or firmware can modify hardware state during suspend/resume, for example on the Toshiba CB35 or Lenovo T400, so log a debug message instead of a warning if the backlight is unexpectedly enabled.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80930
--- drivers/gpu/drm/i915/intel_panel.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-)
drivers/gpu/drm/i915/intel_panel.c +4 -4
@@ -801,7 +801,7 @@ static void pch_enable_backlight(struct intel_connector *connector) cpu_ctl2 =I915_READ (BLC_PWM_CPU_CTL2 );if (cpu_ctl2 &BLM_PWM_ENABLE ) { -WARN (1 ,"cpu backlight already enabled\n" ); +DRM_DEBUG_KMS ("cpu backlight already enabled\n" ); cpu_ctl2 &= ~BLM_PWM_ENABLE ;I915_WRITE (BLC_PWM_CPU_CTL2 , cpu_ctl2); }
@@ -845,7 +845,7 @@ static void i9xx_enable_backlight(struct intel_connector *connector) ctl =I915_READ (BLC_PWM_CTL );if (ctl &BACKLIGHT_DUTY_CYCLE_MASK_PNV ) { -WARN (1 ,"backlight already enabled\n" ); +DRM_DEBUG_KMS ("backlight already enabled\n" );I915_WRITE (BLC_PWM_CTL ,0 ); }
@@ -876,7 +876,7 @@ static void i965_enable_backlight(struct intel_connector *connector) ctl2 =I915_READ (BLC_PWM_CTL2 );if (ctl2 &BLM_PWM_ENABLE ) { -WARN (1 ,"backlight already enabled\n" ); +DRM_DEBUG_KMS ("backlight already enabled\n" ); ctl2 &= ~BLM_PWM_ENABLE ;I915_WRITE (BLC_PWM_CTL2 , ctl2); }
@@ -910,7 +910,7 @@ static void vlv_enable_backlight(struct intel_connector *connector) ctl2 =I915_READ (VLV_BLC_PWM_CTL2 (pipe));if (ctl2 &BLM_PWM_ENABLE ) { -WARN (1 ,"backlight already enabled\n" ); +DRM_DEBUG_KMS ("backlight already enabled\n" ); ctl2 &= ~BLM_PWM_ENABLE ;I915_WRITE (VLV_BLC_PWM_CTL2 (pipe), ctl2); }
Quoted 7 lines · Scot Doyle
BIOS or firmware can modify hardware state during suspend/resume, for example on the Toshiba CB35 or Lenovo T400, so log a debug message instead of a warning if the backlight is unexpectedly enabled.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80930
Cc Jani Nikula <[email protected]>Signed-off-by Scot Doyle <[email protected]>
This should get cleaned up in the modeset state sanitization we do upon resume, so without someone digging into this bug a bit and coming up with an explanation for why that fails I'm reluctant to merge this. -Daniel
Signature · 3 lines
Daniel Vetter Software Engineer, Intel Corporation +41 (0) 79 365 57 48 - http://blog.ffwll.ch
Quoted 5 lines · Daniel Vetter
Quoted 4 lines · Scot Doyle
BIOS or firmware can modify hardware state during suspend/resume, for example on the Toshiba CB35 or Lenovo T400, so log a debug message instead of a warning if the backlight is unexpectedly enabled.
Quoted 8 lines
Quoted 3 lines
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80930
Cc Jani Nikula <[email protected]>Signed-off-by Scot Doyle <[email protected]>This should get cleaned up in the modeset state sanitization we do upon resume, so without someone digging into this bug a bit and coming up with an explanation for why that fails I'm reluctant to merge this. -Daniel
When we enter intel_modeset_setup_hw_state during resume
- BLC_PWM_CPU_CTL2 == BLM_PWM_ENABLE
- the physical backlight is off
- readout_hw_state says crtcs, encoders and connectors are disabled
The sanitizations done before reaching the force_restore block are
- drm_vblank_off for each crtc
- sarea_priv->pipeA_w=0
- sarea_priv->pipeA_h=0
- ilk_wm_get_hw_state(dev)
Then the warning is logged inside the force_restore block
[11.651495] [<ffffffff8106fc5c>] warn_slowpath_fmt+0x5c/0x80 [11.651508] [<ffffffffa0576d0a>] pch_enable_backlight+0x1ba/0x200 [11.651518] [<ffffffffa0577474>] intel_panel_enable_backlight+0xa4/0x100 [11.651529] [<ffffffffa0568514>] intel_edp_backlight_on+0x54/0x140 [11.651540] [<ffffffffa0560c23>] intel_enable_ddi+0xb3/0x100 [11.651552] [<ffffffffa054b869>] haswell_crtc_enable+0x559/0xe80 [11.651564] [<ffffffffa0545ea4>] __intel_set_mode+0xf94/0x1c00 [11.651575] [<ffffffffa055062b>] intel_modeset_setup_hw_state+0x55b/0xd80 [11.651609] [<ffffffffa04eb3a9>] __i915_drm_thaw+0x159/0x1d0 [11.651617] [<ffffffffa04ebcd8>] i915_resume+0x28/0x50
I see no code in the execution path of intel_modeset_setup_hw_state to either note the state of BLC_PWM_CPU_CTL2 or reset it, apart from the pch_enable_backlight function. Which would be one explanation :-)
Quoted 11 lines · Scot Doyle
Quoted 9 lines · Daniel Vetter
Quoted 7 lines · Scot Doyle
BIOS or firmware can modify hardware state during suspend/resume, for example on the Toshiba CB35 or Lenovo T400, so log a debug message instead of a warning if the backlight is unexpectedly enabled.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80930
Cc Jani Nikula <[email protected]>Signed-off-by Scot Doyle <[email protected]>
Quoted 8 lines
Quoted 4 lines
This should get cleaned up in the modeset state sanitization we do upon resume, so without someone digging into this bug a bit and coming up with an explanation for why that fails I'm reluctant to merge this. -Daniel
When we enter
intel_modeset_setup_hw_stateduring resume
-BLC_PWM_CPU_CTL2==BLM_PWM_ENABLE
- the physical backlight is off
Hm, this is actually interesting - we have some other evidence that the best way to shut off the backlight is actually to just set the pwm duty cycle to 0. Can you please check that this is the case for your system?
Maybe we just need to extend the check to look for !PWM_ENABLE || duty_cycle == 0.
In general if we hit upon a WARN it's not a good idea to just shut it up, but to dig a bit deeper and figure out why exactly something doesn't work as we expected it to work.
Thanks, Daniel
Quoted 23 lines
-
readout_hw_statesays crtcs, encoders and connectors are disabledThe sanitizations done before reaching the
force_restoreblock are
-drm_vblank_offfor each crtc
- sarea_priv->pipeA_w=0
- sarea_priv->pipeA_h=0
-ilk_wm_get_hw_state(dev)Then the warning is logged inside the
force_restoreblock[11.651495] [<ffffffff8106fc5c>] warn_slowpath_fmt+0x5c/0x80 [11.651508] [<ffffffffa0576d0a>] pch_enable_backlight+0x1ba/0x200 [11.651518] [<ffffffffa0577474>] intel_panel_enable_backlight+0xa4/0x100 [11.651529] [<ffffffffa0568514>] intel_edp_backlight_on+0x54/0x140 [11.651540] [<ffffffffa0560c23>] intel_enable_ddi+0xb3/0x100 [11.651552] [<ffffffffa054b869>] haswell_crtc_enable+0x559/0xe80 [11.651564] [<ffffffffa0545ea4>] __intel_set_mode+0xf94/0x1c00 [11.651575] [<ffffffffa055062b>] intel_modeset_setup_hw_state+0x55b/0xd80 [11.651609] [<ffffffffa04eb3a9>] __i915_drm_thaw+0x159/0x1d0 [11.651617] [<ffffffffa04ebcd8>] i915_resume+0x28/0x50I see no code in the execution path of
intel_modeset_setup_hw_stateto either note the state ofBLC_PWM_CPU_CTL2or reset it, apart from thepch_enable_backlightfunction. Which would be one explanation :-)
Signature · 3 lines
Daniel Vetter Software Engineer, Intel Corporation +41 (0) 79 365 57 48 - http://blog.ffwll.ch
Quoted 8 lines · Daniel Vetter
Quoted 3 lines · Scot Doyle
When we enter
intel_modeset_setup_hw_stateduring resume
-BLC_PWM_CPU_CTL2==BLM_PWM_ENABLE
- the physical backlight is offHm, this is actually interesting - we have some other evidence that the best way to shut off the backlight is actually to just set the pwm duty cycle to 0. Can you please check that this is the case for your system?
/sys/class/backlight/intel_backlight/brightness
0 -> backlight not visible
1 -> backlight visible
937 -> max backlight
Setting /sys/class/backlight/intel_backlight/brightness to 0 updates BLC_PWM_CPU_CTL, but BLC_PWM_CPU_CTL2 remains 0xe0000000.
Quoted 2 lines
Maybe we just need to extend the check to look for !PWM_ENABLE ||
duty_cycle== 0.
The following measurements hold true no matter the duty cycle before suspend:
When entering hsw_enable_pc8 during suspend
- the physical backlight is off
- BLC_PWM_CPU_CTL == 0x3a900000 (BACKLIGHT_DUTY_CYCLE_MASK == ffff)
- BLC_PWM_CPU_CTL2 == 0x60000000 (BLM_PWM_ENABLE)
When exiting hsw_disable_pc8 during resume
- the physical backlight is off
- BLC_PWM_CPU_CTL == 0x200
- BLC_PWM_CPU_CTL2 == 0x80000000 (BLM_PWM_ENABLE | BLM_TRANSCODER_EDP)
When entering pch_enable_backlight during resume
- the physical backlight is off
- BLC_PWM_CPU_CTL == 0x200
- BLC_PWM_CPU_CTL2 == 0x80000000 (BLM_PWM_ENABLE)
When exiting pch_enable_backlight during resume
- the physical backlight is off
- BLC_PWM_CPU_CTL == duty cycle prior to suspend
- BLC_PWM_CPU_CTL2 == 0xe0000000 (BLM_PWM_ENABLE | BLM_TRANSCODER_EDP)
So the BIOS is setting BLC_PWM_CPU_CTL=0x200 and BLC_PWM_CPU_CTL2=0x80000000 ?
Quoted 40 lines · Scot Doyle
Quoted 8 lines · Daniel Vetter
Quoted 3 lines · Scot Doyle
When we enter
intel_modeset_setup_hw_stateduring resume
-BLC_PWM_CPU_CTL2==BLM_PWM_ENABLE
- the physical backlight is offHm, this is actually interesting - we have some other evidence that the best way to shut off the backlight is actually to just set the pwm duty cycle to 0. Can you please check that this is the case for your system?
/sys/class/backlight/intel_backlight/brightness
0 -> backlight not visible
1 -> backlight visible
937 -> max backlightSetting
/sys/class/backlight/intel_backlight/brightnessto 0 updatesBLC_PWM_CPU_CTL, butBLC_PWM_CPU_CTL2remains0xe0000000.Quoted 2 lines
Maybe we just need to extend the check to look for !PWM_ENABLE ||
duty_cycle== 0.The following measurements hold true no matter the duty cycle before suspend:
When entering
hsw_enable_pc8during suspend
- the physical backlight is off
-BLC_PWM_CPU_CTL==0x3a900000(BACKLIGHT_DUTY_CYCLE_MASK== ffff)
-BLC_PWM_CPU_CTL2==0x60000000(BLM_PWM_ENABLE)When exiting
hsw_disable_pc8during resume
- the physical backlight is off
-BLC_PWM_CPU_CTL==0x200
-BLC_PWM_CPU_CTL2==0x80000000(BLM_PWM_ENABLE|BLM_TRANSCODER_EDP)When entering
pch_enable_backlightduring resume
- the physical backlight is off
-BLC_PWM_CPU_CTL==0x200
-BLC_PWM_CPU_CTL2==0x80000000(BLM_PWM_ENABLE)
Quoted 7 lines
When exiting
pch_enable_backlightduring resume
- the physical backlight is off
-BLC_PWM_CPU_CTL== duty cycle prior to suspend
-BLC_PWM_CPU_CTL2==0xe0000000(BLM_PWM_ENABLE|BLM_TRANSCODER_EDP)So the BIOS is setting BLC_PWM_CPU_CTL=0x200 and BLC_PWM_CPU_CTL2=0x80000000 ?
Indeed the bios seems to just but gunk into that register. And if we add in all the knobs there's piles of them (you have semi-duplicated backlight registers on hsw on the PCH), so I guess it doesn't make sense to combine them all and warn if something goes awry, at least not in a -fixes patch. So Reviewed-by: Daniel Vetter <[email protected]> on your original patch.
Jani can decide whether he wants to save this WARN_ON (imo it's useful to have such sanity-checks) in -next by taking all the various bits and duty cycles into account. But maybe just on the latest platforms, that still should give is good coverage, but with a lot less fuss.
Thanks for tracking this all down.
Cheers, Daniel
Signature · 3 lines
Daniel Vetter Software Engineer, Intel Corporation +41 (0) 79 365 57 48 - http://blog.ffwll.ch
Quoted 56 lines · Daniel Vetter
Quoted 40 lines · Scot Doyle
Quoted 8 lines · Daniel Vetter
Quoted 3 lines · Scot Doyle
When we enter
intel_modeset_setup_hw_stateduring resume
-BLC_PWM_CPU_CTL2==BLM_PWM_ENABLE
- the physical backlight is offHm, this is actually interesting - we have some other evidence that the best way to shut off the backlight is actually to just set the pwm duty cycle to 0. Can you please check that this is the case for your system?
/sys/class/backlight/intel_backlight/brightness
0 -> backlight not visible
1 -> backlight visible
937 -> max backlightSetting
/sys/class/backlight/intel_backlight/brightnessto 0 updatesBLC_PWM_CPU_CTL, butBLC_PWM_CPU_CTL2remains0xe0000000.Quoted 2 lines
Maybe we just need to extend the check to look for !PWM_ENABLE ||
duty_cycle== 0.The following measurements hold true no matter the duty cycle before suspend:
When entering
hsw_enable_pc8during suspend
- the physical backlight is off
-BLC_PWM_CPU_CTL==0x3a900000(BACKLIGHT_DUTY_CYCLE_MASK== ffff)
-BLC_PWM_CPU_CTL2==0x60000000(BLM_PWM_ENABLE)When exiting
hsw_disable_pc8during resume
- the physical backlight is off
-BLC_PWM_CPU_CTL==0x200
-BLC_PWM_CPU_CTL2==0x80000000(BLM_PWM_ENABLE|BLM_TRANSCODER_EDP)When entering
pch_enable_backlightduring resume
- the physical backlight is off
-BLC_PWM_CPU_CTL==0x200
-BLC_PWM_CPU_CTL2==0x80000000(BLM_PWM_ENABLE)Quoted 7 lines
When exiting
pch_enable_backlightduring resume
- the physical backlight is off
-BLC_PWM_CPU_CTL== duty cycle prior to suspend
-BLC_PWM_CPU_CTL2==0xe0000000(BLM_PWM_ENABLE|BLM_TRANSCODER_EDP)So the BIOS is setting BLC_PWM_CPU_CTL=0x200 and BLC_PWM_CPU_CTL2=0x80000000 ?
Indeed the bios seems to just but gunk into that register. And if we add in all the knobs there's piles of them (you have semi-duplicated backlight registers on hsw on the PCH), so I guess it doesn't make sense to combine them all and warn if something goes awry, at least not in a -fixes patch. So Reviewed-by: Daniel Vetter <[email protected]> on your original patch.
Quoted 4 lines
Jani can decide whether he wants to save this
WARN_ON(imo it's useful to have such sanity-checks) in -next by taking all the various bits and duty cycles into account. But maybe just on the latest platforms, that still should give is good coverage, but with a lot less fuss.
Out of curiosity: What are the PCH copies of the backlight registers doing after resume?
-Daniel
Signature · 3 lines
Daniel Vetter Software Engineer, Intel Corporation +41 (0) 79 365 57 48 - http://blog.ffwll.ch
Quoted 8 lines · Daniel Vetter
Quoted 7 lines · Daniel Vetter
Indeed the bios seems to just but gunk into that register. And if we add in all the knobs there's piles of them (you have semi-duplicated backlight registers on hsw on the PCH), so I guess it doesn't make sense to combine them all and warn if something goes awry, at least not in a -fixes patch. So Reviewed-by: Daniel Vetter <[email protected]> on your original patch.
Quoted 7 lines
Quoted 4 lines
Jani can decide whether he wants to save this
WARN_ON(imo it's useful to have such sanity-checks) in -next by taking all the various bits and duty cycles into account. But maybe just on the latest platforms, that still should give is good coverage, but with a lot less fuss.Out of curiosity: What are the PCH copies of the backlight registers doing after resume?
Thanks Daniel, here's the info:
When entering hsw_enable_pc8 during suspend
- the physical backlight is off
- BLC_PWM_CPU_CTL == 0x 3a90000 (BACKLIGHT_DUTY_CYCLE_MASK == ffff)
- BLC_PWM_CPU_CTL2 == 0x60000000
- BLC_PWM_PCH_CTL == 0x 0
- BLC_PWM_PCH_CTL2 == 0x 3a90000
When exiting hsw_disable_pc8 during resume
- the physical backlight is off
- BLC_PWM_CPU_CTL == 0x 200
- BLC_PWM_CPU_CTL2 == 0x80000000 (BLM_PWM_ENABLE)
- BLC_PWM_PCH_CTL == 0x80000000
- BLC_PWM_PCH_CTL2 == 0x 4000000
When entering pch_enable_backlight during resume
- the physical backlight is off
- BLC_PWM_CPU_CTL == 0x 200
- BLC_PWM_CPU_CTL2 == 0x80000000
- BLC_PWM_PCH_CTL == 0x80000000
- BLC_PWM_PCH_CTL2 == 0x 4000000
When exiting pch_enable_backlight during resume
- the physical backlight is off
- BLC_PWM_CPU_CTL == duty cycle prior to suspend
- BLC_PWM_CPU_CTL2 == 0xe0000000 (BLM_PWM_ENABLE | BLM_TRANSCODER_EDP)
- BLC_PWM_PCH_CTL == 0x80000000
- BLC_PWM_PCH_CTL2 == 0x 3a90000
Jani Nikula
AppliedQuoted 47 lines · Daniel Vetter
Quoted 46 lines · Scot Doyle
Quoted 8 lines · Daniel Vetter
Quoted 3 lines · Scot Doyle
When we enter
intel_modeset_setup_hw_stateduring resume
-BLC_PWM_CPU_CTL2==BLM_PWM_ENABLE
- the physical backlight is offHm, this is actually interesting - we have some other evidence that the best way to shut off the backlight is actually to just set the pwm duty cycle to 0. Can you please check that this is the case for your system?
/sys/class/backlight/intel_backlight/brightness
0 -> backlight not visible
1 -> backlight visible
937 -> max backlightSetting
/sys/class/backlight/intel_backlight/brightnessto 0 updatesBLC_PWM_CPU_CTL, butBLC_PWM_CPU_CTL2remains0xe0000000.Quoted 2 lines
Maybe we just need to extend the check to look for !PWM_ENABLE ||
duty_cycle== 0.The following measurements hold true no matter the duty cycle before suspend:
When entering
hsw_enable_pc8during suspend
- the physical backlight is off
-BLC_PWM_CPU_CTL==0x3a900000(BACKLIGHT_DUTY_CYCLE_MASK== ffff)
-BLC_PWM_CPU_CTL2==0x60000000(BLM_PWM_ENABLE)When exiting
hsw_disable_pc8during resume
- the physical backlight is off
-BLC_PWM_CPU_CTL==0x200
-BLC_PWM_CPU_CTL2==0x80000000(BLM_PWM_ENABLE|BLM_TRANSCODER_EDP)When entering
pch_enable_backlightduring resume
- the physical backlight is off
-BLC_PWM_CPU_CTL==0x200
-BLC_PWM_CPU_CTL2==0x80000000(BLM_PWM_ENABLE)When exiting
pch_enable_backlightduring resume
- the physical backlight is off
-BLC_PWM_CPU_CTL== duty cycle prior to suspend
-BLC_PWM_CPU_CTL2==0xe0000000(BLM_PWM_ENABLE|BLM_TRANSCODER_EDP)
Quoted 8 lines
Quoted 1 line
So the BIOS is setting BLC_PWM_CPU_CTL=0x200 and BLC_PWM_CPU_CTL2=0x80000000 ?
Indeed the bios seems to just but gunk into that register. And if we add in all the knobs there's piles of them (you have semi-duplicated backlight registers on hsw on the PCH), so I guess it doesn't make sense to combine them all and warn if something goes awry, at least not in a -fixes patch. So Reviewed-by: Daniel Vetter <[email protected]> on your original patch.
Pushed to drm-intel-fixes, thanks for the patch and review.
BR,
Jani.
Quoted 17 lines
Jani can decide whether he wants to save this
WARN_ON(imo it's useful to have such sanity-checks) in -next by taking all the various bits and duty cycles into account. But maybe just on the latest platforms, that still should give is good coverage, but with a lot less fuss.Thanks for tracking this all down.
Cheers, Daniel
Signature · 7 lines
Daniel Vetter Software Engineer, Intel Corporation +41 (0) 79 365 57 48 - http://blog.ffwll.ch _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Signature · 1 line
Jani Nikula, Intel Open Source Technology Center