arm64: dts: rockchip: add (but disabled) SFC node for Radxa ROCK 5A
Subsystems (2)
PATCH v2 1/2 arm64: dts: rockchip: add (but disabled) SFC node for Radxa ROCK 5A
This commit adds SFC node for Radxa ROCK 5A.
since sdhci and sfc on RK3588s share pins(i.e. exclusive), it cannot be enabled both nodes at the same time. so status = "okay" is omitted here.
you may be able to enable sfc (and disable sdhci) by fdt overlay.
SPI NOR flash chip may vary, so use safe(lowest) spi-max-frequency.
[ upstream commit: 00224650dd45e166ea6eb1593f5f064583963ccf ]
(cherry picked from commit fde218de3133705f3f56dc8eb26baa878f0e0dc9)
---
Changes in v2
- none
--- dts/upstream/src/arm64/rockchip/rk3588s-rock-5a.dts | 13 +++++++++++++ 1 file changed, 13 insertions(+)
dts/upstream/src/arm64/rockchip/rk3588s-rock-5a.dts +13 -0
@@ -377,6 +377,19 @@ status = "okay"; }; +&sfc { + pinctrl-names = "default"; + pinctrl-0 = <&fspim0_pins>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <104000000>; + spi-rx-bus-width = <4>; + spi-tx-bus-width = <1>; + }; +}; + &spi2 { status = "okay"; assigned-clocks = <&cru CLK_SPI2>;
Signature · 1 line
2.43.0
PATCH v2 2/2 rockchip: add support for Radxa ROCK 5A with SPI NOR flash module
on Radxa ROCK 5A, sdhci(eMMC) and fspim0(SPI NOR flash) share pins (i.e. eMMC and SPI NOR flash are exclusive), new defconfig and dts specifically for SPI NOR flash is required.
---
Changes in v2
- fix subject
--- arch/arm/dts/rk3588s-rock-5a-spi-u-boot.dtsi | 24 ++++++ arch/arm/dts/rk3588s-rock-5a-spi.dts | 4 + board/radxa/rock5a-rk3588s/MAINTAINERS | 5 +- configs/rock5a-spi-rk3588s_defconfig | 83 ++++++++++++++++++++ 4 files changed, 113 insertions(+), 3 deletions(-) create mode 100644 arch/arm/dts/rk3588s-rock-5a-spi-u-boot.dtsi create mode 100644 arch/arm/dts/rk3588s-rock-5a-spi.dts create mode 100644 configs/rock5a-spi-rk3588s_defconfig
arch/arm/dts/rk3588s-rock-5a-spi-u-boot.dtsi new file +24 -0
@@ -0,0 +1,24 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2023 Collabora Ltd. + */ + +#include "rk3588s-u-boot.dtsi" + +&fspim0_pins { + bootph-pre-ram; + bootph-some-ram; +}; + +&sdhci { + status = "disabled"; +}; + +&sfc { + status = "okay"; + + flash@0 { + bootph-pre-ram; + bootph-some-ram; + }; +};
arch/arm/dts/rk3588s-rock-5a-spi.dts new file +4 -0
@@ -0,0 +1,4 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) + +/dts-v1/; +#include "rk3588s-rock-5a.dts"
board/radxa/rock5a-rk3588s/MAINTAINERS +2 -3
@@ -4,6 +4,5 @@ R: Jonas Karlman <[email protected]> S: Maintained F: board/radxa/rock5a-rk3588s F: include/configs/rock5a-rk3588s.h -F: configs/rock5a-rk3588s_defconfig -F: arch/arm/dts/rk3588s-rock-5a.dts -F: arch/arm/dts/rk3588s-rock-5a-u-boot.dtsi +F: configs/rock5a* +F: arch/arm/dts/rk3588s-rock-5a*
configs/rock5a-spi-rk3588s_defconfig new file +83 -0
83 lines not on this page · raw message
Signature · 1 line
2.43.0
Re: [PATCH v2 2/2] rockchip: add support for Radxa ROCK 5A with SPI NOR flash module
Hi,
could you review this patch, anyone?
Best regards,
--
FUKAUMI Naoki
Radxa Computer (Shenzhen) Co., Ltd.
Quoted 160 lines · FUKAUMI Naoki
on Radxa ROCK 5A, sdhci(eMMC) and fspim0(SPI NOR flash) share pins (i.e. eMMC and SPI NOR flash are exclusive), new defconfig and dts specifically for SPI NOR flash is required.
Signed-off-by FUKAUMI Naoki <[email protected]>---
Changes in v2
- fix subject--- arch/arm/dts/rk3588s-rock-5a-spi-u-boot.dtsi | 24 ++++++ arch/arm/dts/rk3588s-rock-5a-spi.dts | 4 + board/radxa/rock5a-rk3588s/MAINTAINERS | 5 +- configs/rock5a-spi-rk3588s_defconfig | 83 ++++++++++++++++++++ 4 files changed, 113 insertions(+), 3 deletions(-)create mode 100644
arch/arm/dts/rk3588s-rock-5a-spi-u-boot.dtsicreate mode 100644arch/arm/dts/rk3588s-rock-5a-spi.dtscreate mode 100644 configs/rock5a-spi-rk3588s_defconfigarch/arm/dts/rk3588s-rock-5a-spi-u-boot.dtsi new file +24
-0@@ -0,0 +1,24 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2023 Collabora Ltd. + */ + +#include "rk3588s-u-boot.dtsi" + +&fspim0_pins { + bootph-pre-ram; + bootph-some-ram; +}; + +&sdhci { + status = "disabled"; +}; + +&sfc { + status = "okay"; + + flash@0 { + bootph-pre-ram; + bootph-some-ram; + }; +};arch/arm/dts/rk3588s-rock-5a-spi.dts new file +4
-0@@ -0,0 +1,4 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) + +/dts-v1/; +#include "rk3588s-rock-5a.dts"board/radxa/rock5a-rk3588s/MAINTAINERS +2
-3@@ -4,6 +4,5 @@ R: Jonas Karlman <[email protected]> S: Maintained F: board/radxa/rock5a-rk3588s F: include/configs/rock5a-rk3588s.h -F: configs/rock5a-rk3588s_defconfig -F: arch/arm/dts/rk3588s-rock-5a.dts -F: arch/arm/dts/rk3588s-rock-5a-u-boot.dtsi +F: configs/rock5a* +F: arch/arm/dts/rk3588s-rock-5a*configs/rock5a-spi-rk3588s_defconfig new file +83
-0@@ -0,0 +1,83 @@ +CONFIG_ARM=y +CONFIG_SKIP_LOWLEVEL_INIT=y +CONFIG_COUNTER_FREQUENCY=24000000 +CONFIG_ARCH_ROCKCHIP=y +CONFIG_SF_DEFAULT_SPEED=24000000 +CONFIG_SF_DEFAULT_MODE=0x2000 +CONFIG_DEFAULT_DEVICE_TREE="rk3588s-rock-5a-spi" +CONFIG_ROCKCHIP_RK3588=y +CONFIG_ROCKCHIP_SPI_IMAGE=y +CONFIG_SPL_SERIAL=y +CONFIG_TARGET_ROCK5A_RK3588=y +CONFIG_DEBUG_UART_BASE=0xFEB50000 +CONFIG_DEBUG_UART_CLOCK=24000000 +CONFIG_SPL_SPI_FLASH_SUPPORT=y +CONFIG_SPL_SPI=y +CONFIG_SYS_LOAD_ADDR=0xc00800 +CONFIG_DEBUG_UART=y +CONFIG_FIT=y +CONFIG_FIT_VERBOSE=y +CONFIG_SPL_FIT_SIGNATURE=y +CONFIG_SPL_LOAD_FIT=y +CONFIG_LEGACY_IMAGE_FORMAT=y +CONFIG_DEFAULT_FDT_FILE="rockchip/rk3588s-rock-5a.dtb" +# CONFIG_DISPLAY_CPUINFO is not set +CONFIG_DISPLAY_BOARDINFO_LATE=y +CONFIG_SPL_MAX_SIZE=0x40000 +CONFIG_SPL_PAD_TO=0x7f8000 +# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set +CONFIG_SPL_SPI_LOAD=y +CONFIG_SYS_SPI_U_BOOT_OFFS=0x60000 +CONFIG_SPL_ATF=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_GPT=y +CONFIG_CMD_I2C=y +CONFIG_CMD_MMC=y +CONFIG_CMD_USB=y +# CONFIG_CMD_SETEXPR is not set +CONFIG_CMD_REGULATOR=y +# CONFIG_SPL_DOS_PARTITION is not set +CONFIG_SPL_OF_CONTROL=y +CONFIG_OF_LIVE=y +# CONFIG_OF_UPSTREAM is not set +CONFIG_OF_SPL_REMOVE_PROPS="clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents" +CONFIG_SPL_DM_SEQ_ALIAS=y +CONFIG_SPL_REGMAP=y +CONFIG_SPL_SYSCON=y +CONFIG_SPL_CLK=y +CONFIG_ROCKCHIP_GPIO=y +CONFIG_SYS_I2C_ROCKCHIP=y +CONFIG_MISC=y +CONFIG_SUPPORT_EMMC_RPMB=y +CONFIG_MMC_DW=y +CONFIG_MMC_DW_ROCKCHIP=y +CONFIG_MMC_SDHCI=y +CONFIG_MMC_SDHCI_SDMA=y +CONFIG_MMC_SDHCI_ROCKCHIP=y +CONFIG_SF_DEFAULT_BUS=5 +CONFIG_SPI_FLASH_SFDP_SUPPORT=y +CONFIG_SPI_FLASH_MACRONIX=y +CONFIG_SPI_FLASH_XTX=y +CONFIG_PHY_REALTEK=y +CONFIG_DWC_ETH_QOS=y +CONFIG_DWC_ETH_QOS_ROCKCHIP=y +CONFIG_PHY_ROCKCHIP_INNO_USB2=y +CONFIG_PHY_ROCKCHIP_NANENG_COMBOPHY=y +CONFIG_PHY_ROCKCHIP_USBDP=y +CONFIG_SPL_PINCTRL=y +CONFIG_PWM_ROCKCHIP=y +CONFIG_SPL_RAM=y +CONFIG_BAUDRATE=1500000 +CONFIG_DEBUG_UART_SHIFT=2 +CONFIG_SYS_NS16550_MEM32=y +CONFIG_ROCKCHIP_SFC=y +CONFIG_SYSRESET=y +CONFIG_USB=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_EHCI_GENERIC=y +CONFIG_USB_OHCI_HCD=y +CONFIG_USB_OHCI_GENERIC=y +CONFIG_USB_DWC3=y +CONFIG_USB_DWC3_GENERIC=y +CONFIG_ERRNO_STR=y
Re: [PATCH v2 2/2] rockchip: add support for Radxa ROCK 5A with SPI NOR flash module
Hi Naoki,
Quoted 59 lines · FUKAUMI Naoki
Hi,
could you review this patch, anyone?
Best regards,
Signature · 2 lines
FUKAUMI Naoki Radxa Computer (Shenzhen) Co., Ltd.Quoted 38 lines · FUKAUMI Naoki
on Radxa ROCK 5A, sdhci(eMMC) and fspim0(SPI NOR flash) share pins (i.e. eMMC and SPI NOR flash are exclusive), new defconfig and dts specifically for SPI NOR flash is required.
Signed-off-by FUKAUMI Naoki <[email protected]>---
Changes in v2
- fix subject
---
arch/arm/dts/rk3588s-rock-5a-spi-u-boot.dtsi| 24 ++++++ arch/arm/dts/rk3588s-rock-5a-spi.dts | 4 + board/radxa/rock5a-rk3588s/MAINTAINERS | 5 +- configs/rock5a-spi-rk3588s_defconfig | 83 ++++++++++++++++++++4 files changed, 113 insertions(+), 3 deletions(-)create mode 100644
arch/arm/dts/rk3588s-rock-5a-spi-u-boot.dtsicreate mode 100644arch/arm/dts/rk3588s-rock-5a-spi.dtscreate mode 100644 configs/rock5a-spi-rk3588s_defconfigarch/arm/dts/rk3588s-rock-5a-spi-u-boot.dtsi new file +14
-0@@ -0,0 +1,24 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2023 Collabora Ltd. + */ + +#include "rk3588s-u-boot.dtsi" + +&fspim0_pins { + bootph-pre-ram; + bootph-some-ram; +}; + +&sdhci { + status = "disabled";arch/arm/dts/rk3588s-rock-5a-spi-u-boot.dtsi line 24
Quoted 10 lines
arch/arm/dts/rk3588s-rock-5a-spi-u-boot.dtsi new file +10
-0+}; + +&sfc { + status = "okay"; + + flash@0 { + bootph-pre-ram; + bootph-some-ram; + }; +};
I assume the board can only be fitted with an SPI NOR or an eMMC and not both at the same time? If that's the case, then the status = disabled and status = okay should be in the dts. I assume we want this to be in the Linux kernel first too, either as a separate DTS or with a DTSO (not sure what they will want).
Quoted 20 lines
Quoted 20 lines
arch/arm/dts/rk3588s-rock-5a-spi.dts new file +4
-0@@ -0,0 +1,4 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) + +/dts-v1/; +#include "rk3588s-rock-5a.dts"board/radxa/rock5a-rk3588s/MAINTAINERS +0
-0@@ -4,6 +4,5 @@ R: Jonas Karlman <[email protected]>S: Maintained
F: board/radxa/rock5a-rk3588s
F:include/configs/rock5a-rk3588s.hboard/radxa/rock5a-rk3588s/MAINTAINERS +0
-2-F: configs/rock5a-rk3588s_defconfig -F: arch/arm/dts/rk3588s-rock-5a.dts
Quoted 8 lines
configs/rock5a-spi-rk3588s_defconfig
Quoted 8 lines
board/radxa/rock5a-rk3588s/MAINTAINERS +2
-1-F: arch/arm/dts/rk3588s-rock-5a-u-boot.dtsi +F: configs/rock5a* +F: arch/arm/dts/rk3588s-rock-5a*configs/rock5a-spi-rk3588s_defconfig new file +0
-0
If Radxa starts having many such options, maybe it won't make a lot of sense to duplicate configs but rather have config fragments to change the default DT and add a few symbols that differ from the base (I assume we may have something similar needed for rock 5b+ compared to rock5b for example?
Keeping all configs in sync for essentially same board with small differences may be difficult, maybe using config fragments will help?
Quoted 50 lines
Quoted 50 lines
configs/rock5a-spi-rk3588s_defconfig new file +43
-0@@ -0,0 +1,83 @@ +CONFIG_ARM=y +CONFIG_SKIP_LOWLEVEL_INIT=y +CONFIG_COUNTER_FREQUENCY=24000000 +CONFIG_ARCH_ROCKCHIP=y +CONFIG_SF_DEFAULT_SPEED=24000000 +CONFIG_SF_DEFAULT_MODE=0x2000 +CONFIG_DEFAULT_DEVICE_TREE="rk3588s-rock-5a-spi" +CONFIG_ROCKCHIP_RK3588=y +CONFIG_ROCKCHIP_SPI_IMAGE=y +CONFIG_SPL_SERIAL=y +CONFIG_TARGET_ROCK5A_RK3588=y +CONFIG_DEBUG_UART_BASE=0xFEB50000 +CONFIG_DEBUG_UART_CLOCK=24000000 +CONFIG_SPL_SPI_FLASH_SUPPORT=y +CONFIG_SPL_SPI=y +CONFIG_SYS_LOAD_ADDR=0xc00800 +CONFIG_DEBUG_UART=y +CONFIG_FIT=y +CONFIG_FIT_VERBOSE=y +CONFIG_SPL_FIT_SIGNATURE=y +CONFIG_SPL_LOAD_FIT=y +CONFIG_LEGACY_IMAGE_FORMAT=y +CONFIG_DEFAULT_FDT_FILE="rockchip/rk3588s-rock-5a.dtb" +# CONFIG_DISPLAY_CPUINFO is not set +CONFIG_DISPLAY_BOARDINFO_LATE=y +CONFIG_SPL_MAX_SIZE=0x40000 +CONFIG_SPL_PAD_TO=0x7f8000 +# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set +CONFIG_SPL_SPI_LOAD=y +CONFIG_SYS_SPI_U_BOOT_OFFS=0x60000 +CONFIG_SPL_ATF=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_GPT=y +CONFIG_CMD_I2C=y +CONFIG_CMD_MMC=y +CONFIG_CMD_USB=y +# CONFIG_CMD_SETEXPR is not set +CONFIG_CMD_REGULATOR=y +# CONFIG_SPL_DOS_PARTITION is not set +CONFIG_SPL_OF_CONTROL=y +CONFIG_OF_LIVE=y +# CONFIG_OF_UPSTREAM is not set +CONFIG_OF_SPL_REMOVE_PROPS="clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
configs/rock5a-spi-rk3588s_defconfig new file +5
-0+CONFIG_SPL_DM_SEQ_ALIAS=y +CONFIG_SPL_REGMAP=y +CONFIG_SPL_SYSCON=y +CONFIG_SPL_CLK=y +CONFIG_ROCKCHIP_GPIO=y
Quoted 8 lines
configs/rock5a-spi-rk3588s_defconfig line 56
Quoted 8 lines
configs/rock5a-spi-rk3588s_defconfig new file +8
-0+CONFIG_SYS_I2C_ROCKCHIP=y +CONFIG_MISC=y +CONFIG_SUPPORT_EMMC_RPMB=y +CONFIG_MMC_DW=y +CONFIG_MMC_DW_ROCKCHIP=y +CONFIG_MMC_SDHCI=y +CONFIG_MMC_SDHCI_SDMA=y +CONFIG_MMC_SDHCI_ROCKCHIP=y
I assume out of the MMC_DW_ROCKCHIP and MMC_SDHCI_ROCKCHIP drivers, one isn't needed anymore as it's the one for the eMMC and the other for the SD card?
Cheers,
Quentin
Re: [PATCH v2 2/2] rockchip: add support for Radxa ROCK 5A with SPI NOR flash module
Hi,
Quoted 56 lines · Quentin Schulz
Hi Naoki,
Quoted 53 lines · FUKAUMI Naoki
Hi,
could you review this patch, anyone?
Best regards,
Signature · 2 lines
FUKAUMI Naoki Radxa Computer (Shenzhen) Co., Ltd.Quoted 42 lines · FUKAUMI Naoki
on Radxa ROCK 5A, sdhci(eMMC) and fspim0(SPI NOR flash) share pins (i.e. eMMC and SPI NOR flash are exclusive), new defconfig and dts specifically for SPI NOR flash is required.
Signed-off-by FUKAUMI Naoki <[email protected]>---
Changes in v2
- fix subject
---
arch/arm/dts/rk3588s-rock-5a-spi-u-boot.dtsi| 24 ++++++ arch/arm/dts/rk3588s-rock-5a-spi.dts | 4 + board/radxa/rock5a-rk3588s/MAINTAINERS | 5 +- configs/rock5a-spi-rk3588s_defconfig | 83 ++++++++++++++++++++4 files changed, 113 insertions(+), 3 deletions(-)create mode 100644
arch/arm/dts/rk3588s-rock-5a-spi-u-boot.dtsicreate mode 100644arch/arm/dts/rk3588s-rock-5a-spi.dtscreate mode 100644 configs/rock5a-spi-rk3588s_defconfigarch/arm/dts/rk3588s-rock-5a-spi-u-boot.dtsi new file +18
-0@@ -0,0 +1,24 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2023 Collabora Ltd. + */ + +#include "rk3588s-u-boot.dtsi" + +&fspim0_pins { + bootph-pre-ram; + bootph-some-ram; +}; + +&sdhci { + status = "disabled"; +}; + +&sfc { + status = "okay";
Quoted 8 lines
Quoted 6 lines
arch/arm/dts/rk3588s-rock-5a-spi-u-boot.dtsi line 24
Quoted 6 lines
arch/arm/dts/rk3588s-rock-5a-spi-u-boot.dtsi new file +6
-0+ + flash@0 { + bootph-pre-ram; + bootph-some-ram; + }; +};I assume the board can only be fitted with an SPI NOR or an eMMC and not both at the same time? If that's the case, then the status = disabled and status = okay should be in the dts. I assume we want this to be in the Linux kernel first too, either as a separate DTS or with a DTSO (not sure what they will want).
maybe it's time to update this patch.
https://patchwork.kernel.org/project/linux-rockchip/patch/[email protected]/
rock-5a-base.dtsi (common part)rock-5a.dts (same as current one)
rock-5a-spi-dts
Quoted 22 lines
Quoted 22 lines
Quoted 22 lines
arch/arm/dts/rk3588s-rock-5a-spi.dts new file +4
-0@@ -0,0 +1,4 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) + +/dts-v1/; +#include "rk3588s-rock-5a.dts"board/radxa/rock5a-rk3588s/MAINTAINERS +0
-0@@ -4,6 +4,5 @@ R: Jonas Karlman <[email protected]>S: Maintained
F: board/radxa/rock5a-rk3588s
F:include/configs/rock5a-rk3588s.hboard/radxa/rock5a-rk3588s/MAINTAINERS +1
-3-F: configs/rock5a-rk3588s_defconfig -F: arch/arm/dts/rk3588s-rock-5a.dts -F: arch/arm/dts/rk3588s-rock-5a-u-boot.dtsi +F: configs/rock5a*
Quoted 8 lines
Quoted 6 lines
configs/rock5a-spi-rk3588s_defconfig
Quoted 6 lines
board/radxa/rock5a-rk3588s/MAINTAINERS +1
-0+F: arch/arm/dts/rk3588s-rock-5a*configs/rock5a-spi-rk3588s_defconfig new file +0
-0If Radxa starts having many such options, maybe it won't make a lot of sense to duplicate configs but rather have config fragments to change the default DT and add a few symbols that differ from the base (I assume we may have something similar needed for rock 5b+ compared to rock5b for example?
I'm thinking doing same for ROCK 5C...
https://github.com/RadxaNaoki/u-boot/commits/rock-5c/
Quoted 1 line
Keeping all configs in sync for essentially same board with small differences may be difficult, maybe using config fragments will help?
any "config fragments" doc/example?
Best regards,
--
FUKAUMI Naoki
Radxa Computer (Shenzhen) Co., Ltd.
Quoted 64 lines
Quoted 50 lines
Quoted 50 lines
configs/rock5a-spi-rk3588s_defconfig new file +43
-0@@ -0,0 +1,83 @@ +CONFIG_ARM=y +CONFIG_SKIP_LOWLEVEL_INIT=y +CONFIG_COUNTER_FREQUENCY=24000000 +CONFIG_ARCH_ROCKCHIP=y +CONFIG_SF_DEFAULT_SPEED=24000000 +CONFIG_SF_DEFAULT_MODE=0x2000 +CONFIG_DEFAULT_DEVICE_TREE="rk3588s-rock-5a-spi" +CONFIG_ROCKCHIP_RK3588=y +CONFIG_ROCKCHIP_SPI_IMAGE=y +CONFIG_SPL_SERIAL=y +CONFIG_TARGET_ROCK5A_RK3588=y +CONFIG_DEBUG_UART_BASE=0xFEB50000 +CONFIG_DEBUG_UART_CLOCK=24000000 +CONFIG_SPL_SPI_FLASH_SUPPORT=y +CONFIG_SPL_SPI=y +CONFIG_SYS_LOAD_ADDR=0xc00800 +CONFIG_DEBUG_UART=y +CONFIG_FIT=y +CONFIG_FIT_VERBOSE=y +CONFIG_SPL_FIT_SIGNATURE=y +CONFIG_SPL_LOAD_FIT=y +CONFIG_LEGACY_IMAGE_FORMAT=y +CONFIG_DEFAULT_FDT_FILE="rockchip/rk3588s-rock-5a.dtb" +# CONFIG_DISPLAY_CPUINFO is not set +CONFIG_DISPLAY_BOARDINFO_LATE=y +CONFIG_SPL_MAX_SIZE=0x40000 +CONFIG_SPL_PAD_TO=0x7f8000 +# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set +CONFIG_SPL_SPI_LOAD=y +CONFIG_SYS_SPI_U_BOOT_OFFS=0x60000 +CONFIG_SPL_ATF=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_GPT=y +CONFIG_CMD_I2C=y +CONFIG_CMD_MMC=y +CONFIG_CMD_USB=y +# CONFIG_CMD_SETEXPR is not set +CONFIG_CMD_REGULATOR=y +# CONFIG_SPL_DOS_PARTITION is not set +CONFIG_SPL_OF_CONTROL=y +CONFIG_OF_LIVE=y +# CONFIG_OF_UPSTREAM is not set +CONFIG_OF_SPL_REMOVE_PROPS="clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
configs/rock5a-spi-rk3588s_defconfig new file +5
-0+CONFIG_SPL_DM_SEQ_ALIAS=y +CONFIG_SPL_REGMAP=y +CONFIG_SPL_SYSCON=y +CONFIG_SPL_CLK=y +CONFIG_ROCKCHIP_GPIO=yQuoted 8 lines
configs/rock5a-spi-rk3588s_defconfig line 56
Quoted 8 lines
configs/rock5a-spi-rk3588s_defconfig new file +8
-0+CONFIG_SYS_I2C_ROCKCHIP=y +CONFIG_MISC=y +CONFIG_SUPPORT_EMMC_RPMB=y +CONFIG_MMC_DW=y +CONFIG_MMC_DW_ROCKCHIP=y +CONFIG_MMC_SDHCI=y +CONFIG_MMC_SDHCI_SDMA=y +CONFIG_MMC_SDHCI_ROCKCHIP=yI assume out of the
MMC_DW_ROCKCHIPandMMC_SDHCI_ROCKCHIPdrivers, one isn't needed anymore as it's the one for the eMMC and the other for the SD card?Cheers,
Quentin
Re: [PATCH v2 2/2] rockchip: add support for Radxa ROCK 5A with SPI NOR flash module
Hi Naoki,
Quoted 69 lines · FUKAUMI Naoki
Hi,
Quoted 57 lines · Quentin Schulz
Hi Naoki,
Quoted 54 lines · FUKAUMI Naoki
Hi,
could you review this patch, anyone?
Best regards,
Signature · 2 lines
FUKAUMI Naoki Radxa Computer (Shenzhen) Co., Ltd.Quoted 43 lines · FUKAUMI Naoki
on Radxa ROCK 5A, sdhci(eMMC) and fspim0(SPI NOR flash) share pins (i.e. eMMC and SPI NOR flash are exclusive), new defconfig and dts specifically for SPI NOR flash is required.
Signed-off-by FUKAUMI Naoki <[email protected]>---
Changes in v2
- fix subject
---
arch/arm/dts/rk3588s-rock-5a-spi-u-boot.dtsi| 24 ++++++ arch/arm/dts/rk3588s-rock-5a-spi.dts | 4 + board/radxa/rock5a-rk3588s/MAINTAINERS | 5 +- configs/rock5a-spi-rk3588s_defconfig | 83 ++++++++++++++++
++++4 files changed, 113 insertions(+), 3 deletions(-)create mode 100644
arch/arm/dts/rk3588s-rock-5a-spi-u-boot.dtsicreate mode 100644arch/arm/dts/rk3588s-rock-5a-spi.dtscreate mode 100644 configs/rock5a-spi-rk3588s_defconfigarch/arm/dts/rk3588s-rock-5a-spi-u-boot.dtsi new file +18
-0@@ -0,0 +1,24 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2023 Collabora Ltd. + */ + +#include "rk3588s-u-boot.dtsi" + +&fspim0_pins { + bootph-pre-ram; + bootph-some-ram; +}; + +&sdhci { + status = "disabled"; +}; + +&sfc { + status = "okay";Quoted 8 lines
Quoted 6 lines
arch/arm/dts/rk3588s-rock-5a-spi-u-boot.dtsi line 24
Quoted 6 lines
arch/arm/dts/rk3588s-rock-5a-spi-u-boot.dtsi new file +6
-0+ + flash@0 { + bootph-pre-ram; + bootph-some-ram; + }; +};I assume the board can only be fitted with an SPI NOR or an eMMC and not both at the same time? If that's the case, then the status = disabled and status = okay should be in the dts. I assume we want this to be in the Linux kernel first too, either as a separate DTS or with a DTSO (not sure what they will want).
Quoted 8 lines
maybe it's time to update this patch.
https://eur02.safelinks.protection.outlook.com/? url=https%3A%2F%2Fpatchwork.kernel.org%2Fproject%2Flinux- rockchip%2Fpatch%2F20230913064505.77393-2- naoki%40radxa.com%2F&data=05%7C02%7Cquentin.schulz%40cherry.de%7Cf853dffb859d43c4309f08dcf9315af8%7C5e0e1b5221b54e7b83bb514ec460677e%7C0%7C0%7C638659237600855259%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C0%7C%7C%7C&sdata=S1k4mVpoTXIf2S4npvbQCoUWTgNWdWae2ELb7PvEwQI%3D&reserved=0
rock-5a-base.dtsi(common part)rock-5a.dts(same as current one)
rock-5a-spi-dts
Nice, we'll need a cherry-pick for those whenever they land in https://git.kernel.org/pub/scm/linux/kernel/git/devicetree/devicetree-rebasing.git (doesn't seem to be the case right now though...).
THen a -u-boot.dtsi per variant (rock-5a.dts and rock-5a-spi.dts).
Quoted 31 lines
Quoted 22 lines
Quoted 22 lines
Quoted 22 lines
arch/arm/dts/rk3588s-rock-5a-spi.dts new file +4
-0@@ -0,0 +1,4 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) + +/dts-v1/; +#include "rk3588s-rock-5a.dts"board/radxa/rock5a-rk3588s/MAINTAINERS +0
-0@@ -4,6 +4,5 @@ R: Jonas Karlman <[email protected]>S: Maintained
F: board/radxa/rock5a-rk3588s
F:include/configs/rock5a-rk3588s.hboard/radxa/rock5a-rk3588s/MAINTAINERS +1
-3-F: configs/rock5a-rk3588s_defconfig -F: arch/arm/dts/rk3588s-rock-5a.dts -F: arch/arm/dts/rk3588s-rock-5a-u-boot.dtsi +F: configs/rock5a*Quoted 8 lines
Quoted 6 lines
configs/rock5a-spi-rk3588s_defconfig
Quoted 6 lines
board/radxa/rock5a-rk3588s/MAINTAINERS +1
-0+F: arch/arm/dts/rk3588s-rock-5a*configs/rock5a-spi-rk3588s_defconfig new file +0
-0If Radxa starts having many such options, maybe it won't make a lot of sense to duplicate configs but rather have config fragments to change the default DT and add a few symbols that differ from the base (I assume we may have something similar needed for rock 5b+ compared to rock5b for example?
Quoted 8 lines
I'm thinking doing same for ROCK 5C...
https://eur02.safelinks.protection.outlook.com/? url=https%3A%2F%2Fgithub.com%2FRadxaNaoki%2Fu- boot%2Fcommits%2Frock-5c%2F&data=05%7C02%7Cquentin.schulz%40cherry.de%7Cf853dffb859d43c4309f08dcf9315af8%7C5e0e1b5221b54e7b83bb514ec460677e%7C0%7C0%7C638659237600880322%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C0%7C%7C%7C&sdata=R7VN8bJSvmKT14QQDYFbGmymxh5vsxzKLE3lEIwFCOw%3D&reserved=0
Quoted 1 line
Keeping all configs in sync for essentially same board with small differences may be difficult, maybe using config fragments will help?
any "config fragments" doc/example?
https://docs.u-boot.org/en/latest/board/phytec/phycore-am64x.html
3.1.1
for how to use it.
I don't know how would one generate it. But if you figure it out, it's probably worth adding to the docs ;)
Cheers,
Quentin
Hi,
dts/upstream/src/ inclues this change now, please ignore this patch.
--
FUKAUMI Naoki
Radxa Computer (Shenzhen) Co., Ltd.
Quoted 48 lines · FUKAUMI Naoki
This commit adds SFC node for Radxa ROCK 5A.
since sdhci and sfc on RK3588s share pins(i.e. exclusive), it cannot be enabled both nodes at the same time. so status = "okay" is omitted here.
you may be able to enable sfc (and disable sdhci) by fdt overlay.
SPI NOR flash chip may vary, so use safe(lowest) spi-max-frequency.
Signed-off-by FUKAUMI Naoki <[email protected]>Signed-off-by Heiko Stuebner <[email protected]>[ upstream commit:
00224650dd45e166ea6eb1593f5f064583963ccf](cherry picked from commit
fde218de3133705f3f56dc8eb26baa878f0e0dc9)
---
Changes in v2
- none--- dts/upstream/src/arm64/rockchip/rk3588s-rock-5a.dts | 13 +++++++++++++ 1 file changed, 13 insertions(+)dts/upstream/src/arm64/rockchip/rk3588s-rock-5a.dts +13
-0@@ -377,6 +377,19 @@ status = "okay"; }; +&sfc { + pinctrl-names = "default"; + pinctrl-0 = <&fspim0_pins>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <104000000>; + spi-rx-bus-width = <4>; + spi-tx-bus-width = <1>; + }; +}; + &spi2 { status = "okay"; assigned-clocks = <&cru CLK_SPI2>;