board: sama5d3_xplained: add Falcon boot support
PATCH 1/1 board: sama5d3_xplained: add Falcon boot support
This supports Falcon boot support for Microchip SAMA5D3 Xplained, tested on raw MMC, and on raw NAND.
spl_start_uboot() is has the simplest possible implementation. It doesn't test the environment because enabling environment support currently causes the SPL to exceed its maximum size (64 KiB). It doesn't check the serial for incoming characters either because this functionality currently doesn't seem to work from the SPL on this board.
Settings for Falcon boot from at FAT partition are also added to avoid compile failures when CONFIG_SPL_OS_BOOT is enabled, but this particular case is currently not functional as adding FAT and partition support cause the SPL to be too big again.
--- board/atmel/sama5d3_xplained/sama5d3_xplained.c | 7 +++++++ include/configs/sama5d3_xplained.h | 14 ++++++++++++++ 2 files changed, 21 insertions(+)
board/atmel/sama5d3_xplained/sama5d3_xplained.c +7 -0
@@ -132,6 +132,13 @@ void spl_board_init(void)#endif } +#ifdef CONFIG_SPL_OS_BOOT +int spl_start_uboot (void ) +{ +return 0 ; +} +#endif +static void ddr2_conf (struct atmel_mpddrc_config *ddr2) { ddr2->md = (ATMEL_MPDDRC_MD_DBW_32_BITS |ATMEL_MPDDRC_MD_DDR2_SDRAM );
include/configs/sama5d3_xplained.h +14 -0
@@ -79,4 +79,18 @@#define CONFIG_SYS_NAND_BLOCK_SIZE 0x20000#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0x0 +/* Falcon boot support on raw MMC */ +#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x100/* 128 KiB */ +#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS (CONFIG_CMD_SPL_WRITE_SIZE / 512) +/* U-Boot proper stored by default at 0x200 (256 KiB) */ +#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x1000/* 2MB */ +#define CONFIG_SYS_SPL_ARGS_ADDR 0x22000000 + +/* Falcon boot support on FAT on MMC */ +#define CONFIG_SPL_FS_LOAD_ARGS_NAME "args" +#define CONFIG_SPL_FS_LOAD_KERNEL_NAME "uImage" + +/* Falcon boot support on raw NAND */ +#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x1a0000 +#endif
Signature · 1 line
2.25.1
Quoted 15 lines · Michael Opdenacker
This supports Falcon boot support for Microchip SAMA5D3 Xplained, tested on raw MMC, and on raw NAND.
spl_start_uboot()is has the simplest possible implementation. It doesn't test the environment because enabling environment support currently causes the SPL to exceed its maximum size (64 KiB). It doesn't check the serial for incoming characters either because this functionality currently doesn't seem to work from the SPL on this board.Settings for Falcon boot from at FAT partition are also added to avoid compile failures when
CONFIG_SPL_OS_BOOTis enabled, but this particular case is currently not functional as adding FAT and partition support cause the SPL to be too big again.
Quoted 6 lines
Signed-off-by Michael Opdenacker <[email protected]>--- board/atmel/sama5d3_xplained/sama5d3_xplained.c | 7 +++++++ include/configs/sama5d3_xplained.h | 14 ++++++++++++++ 2 files changed, 21 insertions(+)
Applied to u-boot-atmel/next , thanks !