nl80211: Add LIVE_ADDR_CHANGE feature
Subsystems (2)
PATCH 1/2 nl80211: Add LIVE_ADDR_CHANGE feature
Add a new feature bit signifying that the wireless hardware supports changing the mac address while the underlying net_device is UP. Note that this is slightly different from IFF_LIVE_ADDR_CHANGE as additional restrictions might be imposed by the hardware. Typical restrictions are:
- No connection is active on this interface, e.g. carrier is off
- No scan is in progress
- No offchannel operation is in progress
--- include/uapi/linux/nl80211.h | 9 +++++++++ 1 file changed, 9 insertions(+)
include/uapi/linux/nl80211.h +9 -0
@@ -5481,6 +5481,14 @@ enum nl80211_feature_flags {* @NL80211_EXT_FEATURE_SAE_OFFLOAD: Device wants to do SAE authentication in * station mode (SAE password is passed as part of the connect command). * +* @NL80211_EXT_FEATURE_LIVE_ADDR_CHANGE: Device can perform a MAC address +* change without having to bring the underlying network device down +* first. For example, in station mode this can be used to vary the +* origin MAC address prior to a connection to a new AP for privacy +* or other reasons. Note that certain driver specific restrictions +* might apply, e.g. no scans in progress, no offchannel operations +* in progress, and no active connections. +* * @NUM_NL80211_EXT_FEATURES: number of extended features. * @MAX_NL80211_EXT_FEATURES: highest extended feature index. */
@@ -5526,6 +5534,7 @@ enum nl80211_ext_feature_index {NL80211_EXT_FEATURE_EXT_KEY_ID ,NL80211_EXT_FEATURE_STA_TX_PWR ,NL80211_EXT_FEATURE_SAE_OFFLOAD , +NL80211_EXT_FEATURE_LIVE_ADDRESS_CHANGE ,/* add new features before the definition below */ NUM_NL80211_EXT_FEATURES,
Signature · 1 line
2.17.1
PATCH 2/2 mac80211: Support LIVE_ADDRESS_CHANGE feature
--- net/mac80211/iface.c | 51 ++++++++++++++++++++++++++++++++++++++++++-- net/mac80211/main.c | 1 + 2 files changed, 50 insertions(+), 2 deletions(-)
net/mac80211/iface.c +49 -2
@@ -198,15 +198,57 @@ static int ieee80211_verify_mac(struct ieee80211_sub_if_data *sdata, u8 *addr,return ret; } +static int ieee80211_can_live_addr_change (struct ieee80211_sub_if_data *sdata) +{ +if (netif_carrier_ok (sdata->dev)) +return -EBUSY ; + +switch (sdata->vif.type) { +case NL80211_IFTYPE_AP : +case NL80211_IFTYPE_P2P_GO : +case NL80211_IFTYPE_AP_VLAN : +case NL80211_IFTYPE_WDS : +case NL80211_IFTYPE_MESH_POINT : +case NL80211_IFTYPE_MONITOR : +case NL80211_IFTYPE_OCB : +/* No further checking required, when started or UP these +* interface types set carrier +*/ +break ; +case NL80211_IFTYPE_ADHOC : +if (sdata->u.ibss.ssid_len !=0 ) +return -EBUSY ; +break ; +case NL80211_IFTYPE_STATION : +case NL80211_IFTYPE_P2P_CLIENT : +if (!list_empty (&sdata->local->roc_list) || + !sdata->local->scanning) +return -EBUSY ; +break ; +default : +return -EOPNOTSUPP ; + } + +return 0 ; +} + +static int ieee80211_change_mac (struct net_device *dev,void *addr) {struct ieee80211_sub_if_data *sdata =IEEE80211_DEV_TO_SUB_IF (dev); +struct ieee80211_local *local = sdata->local;struct sockaddr *sa = addr;bool check_dup = true; +bool live = false;int ret; -if (ieee80211_sdata_running (sdata)) -return -EBUSY ; +if (ieee80211_sdata_running (sdata)) { + ret =ieee80211_can_live_addr_change (sdata); +if (ret) +return ret; + + live = true; + }if (sdata->vif.type ==NL80211_IFTYPE_MONITOR && !(sdata->u.mntr.flags &MONITOR_FLAG_ACTIVE ))
@@ -216,7 +258,11 @@ static int ieee80211_change_mac(struct net_device *dev, void *addr)if (ret)return ret; +if (live) +drv_remove_interface (local, sdata); ret =eth_mac_addr (dev, sa); +if (live) +drv_add_interface (local, sdata);if (ret ==0 )memcpy (sdata->vif.addr, sa->sa_data,ETH_ALEN );
@@ -1871,6 +1917,7 @@ int ieee80211_if_add(struct ieee80211_local *local, const char *name, sdata->u.mgd.use_4addr = params->use_4addr; ndev->features |= local->hw.netdev_features; + ndev->priv_flags |=IFF_LIVE_ADDR_CHANGE ;netdev_set_default_ethtool_ops (ndev, &ieee80211_ethtool_ops);
net/mac80211/main.c +1 -0
@@ -596,6 +596,7 @@ struct ieee80211_hw *ieee80211_alloc_hw_nm(size_t priv_data_len,wiphy_ext_feature_set (wiphy,NL80211_EXT_FEATURE_TXQS );wiphy_ext_feature_set (wiphy,NL80211_EXT_FEATURE_RRM ); +wiphy_ext_feature_set (wiphy,NL80211_EXT_FEATURE_LIVE_ADDRESS_CHANGE ); wiphy->bss_priv_size =sizeof (struct ieee80211_bss );
Signature · 1 line
2.17.1
Johannes Berg
maintainerRe: [PATCH 2/2] mac80211: Support LIVE_ADDRESS_CHANGE feature
Hi,
I was tempted to apply this (sans the feature advertisement part that I don't think should be in nl80211), but:
Quoted 2 lines
Signed-off-by James Prestwood <[email protected]>
Please add a commit log.
Quoted 10 lines
net/mac80211/iface.c +10
-0+static int ieee80211_can_live_addr_change (struct ieee80211_sub_if_data *sdata) +{ +if (netif_carrier_ok (sdata->dev)) +return -EBUSY ; + +switch (sdata->vif.type) { +case NL80211_IFTYPE_AP : +case NL80211_IFTYPE_P2P_GO : +case NL80211_IFTYPE_AP_VLAN : +case NL80211_IFTYPE_WDS :
net/mac80211/iface.c static int ieee80211_verify_mac(struct ieee80211_sub_if_data *sdata, u8 *addr, · line 220
Quoted 10 lines
net/mac80211/iface.c +10
-0+case NL80211_IFTYPE_MESH_POINT : +case NL80211_IFTYPE_MONITOR : +case NL80211_IFTYPE_OCB : +/* No further checking required, when started or UP these +* interface types set carrier +*/ +break ; +case NL80211_IFTYPE_ADHOC : +if (sdata->u.ibss.ssid_len !=0 ) +return -EBUSY ;
Can you please document why this is there? Maybe all of the conditions, for that matter.
I'm not even entirely sure it _is_ needed - if we've still not created the IBSS but are scanning for it or trying to merge the MAC address won't really matter yet? Probably?
net/mac80211/iface.c static int ieee80211_verify_mac(struct ieee80211_sub_if_data *sdata, u8 *addr, · line 226
Quoted 6 lines
net/mac80211/iface.c +6
-0+break ; +case NL80211_IFTYPE_STATION : +case NL80211_IFTYPE_P2P_CLIENT : +if (!list_empty (&sdata->local->roc_list) || + !sdata->local->scanning) +return -EBUSY ;
AP, mesh and other interfaces *can* scan, so that test should be pulled out to be generic - but then in fact all of them should probably be generic - ROC maybe can't be done on other interfaces yet, but unless you're going to check *which* interface is actually doing the ROC, you should just make that a generic check that applies to all interfaces.
If you do care about this being more granular then you should check *which* interface is scanning, and then you can still switch the MAC address for *other* interfaces - but I'd still argue it should be independent of interface type.
And, I'm confused, but isn't the polarity of the scanning check wrong?
johannes
Re: [PATCH 2/2] mac80211: Support LIVE_ADDRESS_CHANGE feature
Quoted 38 lines · Johannes Berg
Hi,
I was tempted to apply this (sans the feature advertisement part that I
don't think should be in nl80211), but:Quoted 2 lines
Signed-off-by James Prestwood <[email protected]>Please add a commit log.
Quoted 16 lines
+static int ieee80211_can_live_addr_change(struct
ieee80211_sub_if_data*sdata)net/mac80211/iface.c +13
-0+{ +if (netif_carrier_ok (sdata->dev)) +return -EBUSY ; + +switch (sdata->vif.type) { +case NL80211_IFTYPE_AP : +case NL80211_IFTYPE_P2P_GO : +case NL80211_IFTYPE_AP_VLAN : +case NL80211_IFTYPE_WDS : +case NL80211_IFTYPE_MESH_POINT : +case NL80211_IFTYPE_MONITOR : +case NL80211_IFTYPE_OCB : +/* No further checking required, when started or UP these
net/mac80211/iface.c static int ieee80211_verify_mac(struct ieee80211_sub_if_data *sdata, u8 *addr, · line 220
Quoted 6 lines
net/mac80211/iface.c +6
-0+* interface types set carrier +*/ +break ; +case NL80211_IFTYPE_ADHOC : +if (sdata->u.ibss.ssid_len !=0 ) +return -EBUSY ;Can you please document why this is there? Maybe all of the conditions,
for that matter.
Quoted 4 lines
I'm not even entirely sure it _is_ needed - if we've still not created
the IBSS but are scanning for it or trying to merge the MAC address won't really matter yet? Probably?
I guess its just paranoia, rather be safe than sorry. I can take this out, but is "Probably?" a good reason? ;)
Quoted 15 lines
net/mac80211/iface.c static int ieee80211_verify_mac(struct ieee80211_sub_if_data *sdata, u8 *addr, · line 226
Quoted 7 lines
net/mac80211/iface.c +6
-0+break ; +case NL80211_IFTYPE_STATION : +case NL80211_IFTYPE_P2P_CLIENT : +if (!list_empty (&sdata->local->roc_list) || + !sdata->local->scanning) +return -EBUSY ;AP, mesh and other interfaces *can* scan, so that test should be pulled
out to be generic - but then in fact all of them should probably be generic - ROC maybe can't be done on other interfaces yet, but unless you're going to check *which* interface is actually doing the ROC, you
should just make that a generic check that applies to all interfaces.
Ok so no switch statement, simply just check that we aren't offchannel or scanning. I guess this would then cover the IBSS case too.
Quoted 5 lines
If you do care about this being more granular then you should check *which* interface is scanning, and then you can still switch the MAC address for *other* interfaces - but I'd still argue it should be independent of interface type.
I think maybe in the future we might want this, but for now lets not worry about it. But just to make sure we are on the same page, your talking about e.g. hardware with multiple radios so you could be doing offchannel work/scanning/connecting simultaneously without having to wait for the current operation to complete?
Quoted 3 lines
And, I'm confused, but isn't the polarity of the scanning check wrong?
Ah yeah, after you pointed that out I realized 'scanning' is a bit field. I should be doing:
test_bit(SCAN_HW_SCANNING, &sdata->local->scanning)
Feel free the merge this, but I haven t had a chance yet to look into adding a flag to RTNL (based on what you said in your previous email). Without some way of telling userspace this is supported, its kinda useless IMO.
Either way I'll send another patch with these things addressed.
Thanks,
James
Quoted 3 lines
johannes
Re: [PATCH 2/2] mac80211: Support LIVE_ADDRESS_CHANGE feature
Hi Johannes,
After thinking about this more:
Quoted 66 lines · James Prestwood
Quoted 39 lines · Johannes Berg
Hi,
I was tempted to apply this (sans the feature advertisement part that
I
don't think should be in nl80211), but:Quoted 2 lines
Signed-off-by James Prestwood <[email protected]>Please add a commit log.
Quoted 16 lines
+static int ieee80211_can_live_addr_change(struct
ieee80211_sub_if_data*sdata)net/mac80211/iface.c +13
-0+{ +if (netif_carrier_ok (sdata->dev)) +return -EBUSY ; + +switch (sdata->vif.type) { +case NL80211_IFTYPE_AP : +case NL80211_IFTYPE_P2P_GO : +case NL80211_IFTYPE_AP_VLAN : +case NL80211_IFTYPE_WDS : +case NL80211_IFTYPE_MESH_POINT : +case NL80211_IFTYPE_MONITOR : +case NL80211_IFTYPE_OCB : +/* No further checking required, when started or UP these
net/mac80211/iface.c static int ieee80211_verify_mac(struct ieee80211_sub_if_data *sdata, u8 *addr, · line 220
Quoted 6 lines
net/mac80211/iface.c +6
-0+* interface types set carrier +*/ +break ; +case NL80211_IFTYPE_ADHOC : +if (sdata->u.ibss.ssid_len !=0 ) +return -EBUSY ;Can you please document why this is there? Maybe all of the conditions,
for that matter.Quoted 4 lines
I'm not even entirely sure it _is_ needed - if we've still not created
the IBSS but are scanning for it or trying to merge the MAC address won't really matter yet? Probably?I guess its just paranoia, rather be safe than sorry. I can take this out, but is "Probably?" a good reason? ;)
Quoted 17 lines
net/mac80211/iface.c static int ieee80211_verify_mac(struct ieee80211_sub_if_data *sdata, u8 *addr, · line 226
Quoted 7 lines
net/mac80211/iface.c +6
-0+break ; +case NL80211_IFTYPE_STATION : +case NL80211_IFTYPE_P2P_CLIENT : +if (!list_empty (&sdata->local->roc_list) || + !sdata->local->scanning) +return -EBUSY ;AP, mesh and other interfaces *can* scan, so that test should be pulled
out to be generic - but then in fact all of them should probably be generic - ROC maybe can't be done on other interfaces yet, but unless
you're going to check *which* interface is actually doing the ROC, you
should just make that a generic check that applies to all interfaces.
Quoted 10 lines
Ok so no switch statement, simply just check that we aren't offchannel
or scanning. I guess this would then cover the IBSS case too.Quoted 6 lines
If you do care about this being more granular then you should check *which* interface is scanning, and then you can still switch the MAC
address for *other* interfaces - but I'd still argue it should be independent of interface type.
So yes these can scan, but this should be covered by the netif_carrier_ok check which is done first. We can just remove the switch entirely, but the roc_list/scanning check only matters for station/p2p_client so checking for the other interface types is kinda pointless and redundant.
Also I am not sure what you mean by *which* interface. This function is called on a single interface, so checking what other interfaces are doing seems strange...
Quoted 26 lines
Quoted 4 lines
And, I'm confused, but isn't the polarity of the scanning check wrong?
Ah yeah, after you pointed that out I realized 'scanning' is a bit field. I should be doing:
test_bit(SCAN_HW_SCANNING, &sdata->local->scanning)Feel free the merge this, but I haven t had a chance yet to look into adding a flag to RTNL (based on what you said in your previous email).
Without some way of telling userspace this is supported, its kinda useless IMO.Either way I'll send another patch with these things addressed.
Thanks,
JamesQuoted 3 lines
johannes
Johannes Berg
maintainerRe: [PATCH 2/2] mac80211: Support LIVE_ADDRESS_CHANGE feature
Hi,
Quoted 8 lines
Quoted 5 lines
Quoted 5 lines
If you do care about this being more granular then you should check *which* interface is scanning, and then you can still switch the MAC
address for *other* interfaces - but I'd still argue it should be independent of interface type.So yes these can scan, but this should be covered by the
netif_carrier_okcheck which is done first.
Not sure what you mean by that.
You could have two interfaces, one which is scanning right now, right? And then theoretically you don't care about the other one - it *should* be OK to remove/re-add (with new MAC address) the one that *isn't* scanning, right?
But we don't have that granularity here for anything - you're just checking "sdata->local->something", and by going from sdata to local you've now checked the whole NIC, not just a single interface on that NIC.
Which is fine, no complaint from me, just in that case you end up failing when really there isn't much need to fail. In fact, in a case like this, actually clearing IFF_UP, changing address and setting IFF_UP would work, concurrently with another interface scanning.
Quoted 4 lines
We can just remove the
switch entirely, but the roc_list/scanning check only matters for station/p2p_client so checking for the other interface types is kinda pointless and redundant.
But it's also completely confusing to do it this way because you go from "sdata" to "local", and at that point the data that you're working on is no longer specific to that one interface, it's actually for the whole NIC.
Basically what I'm saying is this: it's confusing and makes no sense to do something like
if (this_is_a_certain_netdev_type) check_some_global_data();
Quoted 3 lines
Also I am not sure what you mean by *which* interface. This function is called on a single interface, so checking what other interfaces are doing seems strange...
My point exactly - but that's what you're doing here in the code. Now I think perhaps without even realizing?
johannes
Re: [PATCH 2/2] mac80211: Support LIVE_ADDRESS_CHANGE feature
Hi Johannes,
Quoted 11 lines · Johannes Berg
Hi,
Quoted 8 lines
Quoted 5 lines
Quoted 5 lines
If you do care about this being more granular then you should check *which* interface is scanning, and then you can still switch the MAC
address for *other* interfaces - but I'd still argue it should be independent of interface type.So yes these can scan, but this should be covered by the
netif_carrier_okcheck which is done first.
Quoted 6 lines
Not sure what you mean by that.
You could have two interfaces, one which is scanning right now, right? And then theoretically you don't care about the other one - it *should* be OK to remove/re-add (with new MAC address) the one that *isn't* scanning, right?
Actually, I don't think you can? Unless I'm missing something? All the scan state is stored on struct ieee80211_local, so if that struct is allocated per phy as you point out below, then what you suggest is currently not possible?
Quoted 5 lines
But we don't have that granularity here for anything - you're just checking "
sdata->local->something", and by going from sdata to local you've now checked the whole NIC, not just a single interface on that NIC.
Right. But that seems to be a limitation of mac80211 actually. We can't run two scans concurrently on different interfaces. This is rather unintuitive given that scan requests require an ifindex/wdev.
Can this be changed / fixed in mac80211 actually? I would expect that if a card supports p2p and station simultaneously, then it can scan / go offchannel on two interfaces simultaneously? Or not? What can iwlwifi do for example?
Quoted 11 lines
Which is fine, no complaint from me, just in that case you end up failing when really there isn't much need to fail. In fact, in a case like this, actually clearing
IFF_UP, changing address and settingIFF_UPwould work, concurrently with another interface scanning.Quoted 4 lines
We can just remove the
switch entirely, but the roc_list/scanning check only matters for station/p2p_client so checking for the other interface types is kinda pointless and redundant.
Quoted 4 lines
But it's also completely confusing to do it this way because you go from "sdata" to "local", and at that point the data that you're working on is no longer specific to that one interface, it's actually for the whole NIC.
I agree its confusing, but that seems to be how mac80211 works?
Quoted 7 lines
Basically what I'm saying is this: it's confusing and makes no sense to do something like
if (this_is_a_certain_netdev_type) check_some_global_data();
Quoted 7 lines
Quoted 3 lines
Also I am not sure what you mean by *which* interface. This function is called on a single interface, so checking what other interfaces are doing seems strange...
My point exactly - but that's what you're doing here in the code. Now I think perhaps without even realizing?
Given the above, I'm not sure I see anything wrong? The switch/case can probably be gotten rid of, but it actually makes things clear that only station/p2p_device and adhoc are handled specially.
Regards,
-Denis
Johannes Berg
maintainerRe: [PATCH 2/2] mac80211: Support LIVE_ADDRESS_CHANGE feature
Hi,
Quoted 9 lines
Quoted 4 lines
You could have two interfaces, one which is scanning right now, right? And then theoretically you don't care about the other one - it *should* be OK to remove/re-add (with new MAC address) the one that *isn't* scanning, right?
Actually, I don't think you can? Unless I'm missing something? All the scan state is stored on struct
ieee80211_local, so if that struct is allocated per phy as you point out below, then what you suggest is currently not possible?
?
The scan_req struct contains a reference to which interface is scanning, so it should very well be possible to have
phy0:
wlan0: IFF_UP & scanning
wlan1: IFF_UP & change MAC address all the time
just like it's possible to change the MAC address when wlan1 *isn't* IFF_UP even if wlan0 is scanning, right?
Quoted 5 lines
Quoted 4 lines
But we don't have that granularity here for anything - you're just checking "
sdata->local->something", and by going from sdata to local you've now checked the whole NIC, not just a single interface on that NIC.
Quoted 8 lines
Right. But that seems to be a limitation of mac80211 actually. We can't run two scans concurrently on different interfaces. This is rather unintuitive given that scan requests require an ifindex/wdev.
Can this be changed / fixed in mac80211 actually? I would expect that if a card supports p2p and station simultaneously, then it can scan / go offchannel on two interfaces simultaneously? Or not? What can iwlwifi do for example?
No, this typically cannot be fixed, and it doesn't really make sense. The NIC cannot possibly do two scans at a time since it has only a single radio resource :-)
Quoted 6 lines
Quoted 4 lines
But it's also completely confusing to do it this way because you go from "sdata" to "local", and at that point the data that you're working on is no longer specific to that one interface, it's actually for the whole NIC.
I agree its confusing, but that seems to be how mac80211 works?
See above.
Quoted 3 lines
Given the above, I'm not sure I see anything wrong? The switch/case can probably be gotten rid of, but it actually makes things clear that only station/p2p_device and adhoc are handled specially.
I just don't think they *should* be handled specially.
Given your code now, you can have
phy0:
wlan0: STATION, IFF_UP & something is doing remain-on-channel
wlan1: STATION, IFF_UP
--> cannot change wlan1 MAC address
phy0:
wlan0: STATION, IFF_UP & something is doing remain-on-channel
wlan1: AP, IFF_UP
--> *can* change wlan1 MAC address
This doesn't really make much sense?
johannes
Re: [PATCH 2/2] mac80211: Support LIVE_ADDRESS_CHANGE feature
Hi Johannes,
Quoted 17 lines · Johannes Berg
Hi,
Quoted 9 lines
Quoted 4 lines
You could have two interfaces, one which is scanning right now, right? And then theoretically you don't care about the other one - it *should* be OK to remove/re-add (with new MAC address) the one that *isn't* scanning, right?
Actually, I don't think you can? Unless I'm missing something? All the scan state is stored on struct
ieee80211_local, so if that struct is allocated per phy as you point out below, then what you suggest is currently not possible??
The
scan_reqstruct contains a reference to which interface is scanning, so it should very well be possible to have
Quoted 7 lines
phy0:
wlan0:IFF_UP& scanning
wlan1:IFF_UP& change MAC address all the timejust like it's possible to change the MAC address when wlan1 *isn't*
IFF_UPeven if wlan0 is scanning, right?
Indeed. But that is not what you were suggesting earlier with just checking local->scanning. So if scan_req contains a wdev, then yes it should be possible to compare the scan_req->wdev to the interface being changed.
Quoted 9 lines
Quoted 9 lines
Quoted 4 lines
But we don't have that granularity here for anything - you're just checking "
sdata->local->something", and by going from sdata to local you've now checked the whole NIC, not just a single interface on that NIC.Right. But that seems to be a limitation of mac80211 actually. We can't run two scans concurrently on different interfaces. This is rather unintuitive given that scan requests require an ifindex/wdev.
Quoted 8 lines
Quoted 4 lines
Can this be changed / fixed in mac80211 actually? I would expect that if a card supports p2p and station simultaneously, then it can scan / go offchannel on two interfaces simultaneously? Or not? What can iwlwifi do for example?
No, this typically cannot be fixed, and it doesn't really make sense. The NIC cannot possibly do two scans at a time since it has only a single radio resource :-)
So why is the scan request not per phy then? And should mac address even affect the ongoing scan? Can we simply change it with the scan ongoing?
Quoted 7 lines
Quoted 4 lines
Given the above, I'm not sure I see anything wrong? The switch/case can probably be gotten rid of, but it actually makes things clear that only station/p2p_device and adhoc are handled specially.
I just don't think they *should* be handled specially.
Fair enough.
Quoted 8 lines
Given your code now, you can have
phy0:
wlan0: STATION,IFF_UP& something is doing remain-on-channel
wlan1: STATION,IFF_UP--> cannot change wlan1 MAC address
Quoted 9 lines
phy0:
wlan0: STATION,IFF_UP& something is doing remain-on-channelwlan1: AP,
IFF_UP--> *can* change wlan1 MAC address
This doesn't really make much sense?
Agreed.
Regards,
-Denis
Johannes Berg
maintainerRe: [PATCH 2/2] mac80211: Support LIVE_ADDRESS_CHANGE feature
Hi,
Quoted 7 lines
Quoted 7 lines
The
scan_reqstruct contains a reference to which interface is scanning, so it should very well be possible to havephy0:
wlan0:IFF_UP& scanning
wlan1:IFF_UP& change MAC address all the time
Quoted 8 lines
Quoted 3 lines
just like it's possible to change the MAC address when wlan1 *isn't*
IFF_UPeven if wlan0 is scanning, right?Indeed. But that is not what you were suggesting earlier with just checking
local->scanning. So ifscan_reqcontains a wdev, then yes it should be possible to compare thescan_req->wdevto the interface being changed.
Well, yes, but only because I was incrementally going from James's patch, which was checking that only.
Similar with the other local-> things being checked here, btw, though in some cases it might be harder to actually determine which wdev is doing something and which isn't.
Quoted 7 lines
Quoted 3 lines
No, this typically cannot be fixed, and it doesn't really make sense. The NIC cannot possibly do two scans at a time since it has only a single radio resource :-)
So why is the scan request not per phy then? And should mac address even affect the ongoing scan? Can we simply change it with the scan ongoing?
There are things that affect the scan from the interface, e.g. capability overrides, (extended) capabilities, the MAC address is used unless randomization is requested, etc.
johannes
Re: [PATCH 2/2] mac80211: Support LIVE_ADDRESS_CHANGE feature
Hi Johannes,
Quoted 7 lines
Quoted 4 lines
Indeed. But that is not what you were suggesting earlier with just checking
local->scanning. So ifscan_reqcontains a wdev, then yes it should be possible to compare thescan_req->wdevto the interface being changed.Well, yes, but only because I was incrementally going from James's patch, which was checking that only.
Well, something to improve. Sometimes it is pretty hard to figure out what you mean.
Quoted 4 lines
Similar with the other local-> things being checked here, btw, though in some cases it might be harder to actually determine which wdev is doing something and which isn't.
Right
Quoted 5 lines
Quoted 5 lines
Quoted 4 lines
No, this typically cannot be fixed, and it doesn't really make sense. The NIC cannot possibly do two scans at a time since it has only a single radio resource :-)
Quoted 8 lines
Quoted 3 lines
So why is the scan request not per phy then? And should mac address even affect the ongoing scan? Can we simply change it with the scan ongoing?
There are things that affect the scan from the interface, e.g. capability overrides, (extended) capabilities, the MAC address is used unless randomization is requested, etc.
But they shouldn't change due a mac address change? I wonder if we can further relax the requirements to allow mac change if NL80211_SCAN_FLAG_RANDOM_ADDR was used?
Regards,
-Denis
Johannes Berg
maintainerRe: [PATCH 2/2] mac80211: Support LIVE_ADDRESS_CHANGE feature
Quoted 9 lines
Quoted 9 lines
Quoted 8 lines
Quoted 4 lines
No, this typically cannot be fixed, and it doesn't really make sense. The NIC cannot possibly do two scans at a time since it has only a single radio resource :-)
So why is the scan request not per phy then? And should mac address even affect the ongoing scan? Can we simply change it with the scan ongoing?
Quoted 8 lines
Quoted 4 lines
There are things that affect the scan from the interface, e.g. capability overrides, (extended) capabilities, the MAC address is used unless randomization is requested, etc.
But they shouldn't change due a mac address change? I wonder if we can further relax the requirements to allow mac change if
NL80211_SCAN_FLAG_RANDOM_ADDRwas used?
No, at least with HW scan that would completely confuse the driver - since from the driver's POV we'd remove the interface it's currently managing the scan for.
johannes
Re: [PATCH 2/2] mac80211: Support LIVE_ADDRESS_CHANGE feature
Hi Johannes,
Quoted 7 lines
Quoted 3 lines
But they shouldn't change due a mac address change? I wonder if we can further relax the requirements to allow mac change if
NL80211_SCAN_FLAG_RANDOM_ADDRwas used?No, at least with HW scan that would completely confuse the driver - since from the driver's POV we'd remove the interface it's currently managing the scan for.
So help me understand this better. Just by virtue of copying the new mac into sdata->vif.addr we'd be confusing the driver such that it can't associate the ongoing scan request to the wdev it was started on? Even when it has all this info? I mean you have a single scan request on a phy, how hard can this be? :)
Note that some apps perform poor-man's scan address randomization by varying the mac (I assume prior to each nth scan). So being able to change the mac while scanning might be a boon to them. I personally don't think changing mac via rtnl to accomplish this is a great idea, but just tossing it out for you.
Regards,
-Denis
Johannes Berg
maintainerRe: [PATCH 2/2] mac80211: Support LIVE_ADDRESS_CHANGE feature
Quoted 11 lines · Denis Kenzior
Hi Johannes,
Quoted 7 lines
Quoted 3 lines
But they shouldn't change due a mac address change? I wonder if we can further relax the requirements to allow mac change if
NL80211_SCAN_FLAG_RANDOM_ADDRwas used?No, at least with HW scan that would completely confuse the driver - since from the driver's POV we'd remove the interface it's currently managing the scan for.
So help me understand this better.
include/net/mac80211.h:
int (*hw_scan)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
struct ieee80211_scan_request *req);How is it difficult to understand that with an API like that, it might not be a good idea to remove the vif from the driver while it's scanning?
Quoted 2 lines
Just by virtue of copying the new
mac intosdata->vif.addr
That's not what happens?
johannes
Re: [PATCH 2/2] mac80211: Support LIVE_ADDRESS_CHANGE feature
Hi Johannes,
Quoted 13 lines · Johannes Berg
Quoted 11 lines · Denis Kenzior
Hi Johannes,
Quoted 7 lines
Quoted 3 lines
But they shouldn't change due a mac address change? I wonder if we can further relax the requirements to allow mac change if
NL80211_SCAN_FLAG_RANDOM_ADDRwas used?No, at least with HW scan that would completely confuse the driver - since from the driver's POV we'd remove the interface it's currently managing the scan for.
So help me understand this better.
Quoted 8 lines
include/net/mac80211.h:int (*hw_scan)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, struct ieee80211_scan_request *req);How is it difficult to understand that with an API like that, it might not be a good idea to remove the vif from the driver while it's scanning?
Right, so you're talking in the context of this implementation which performs a remove/add interface. You're right about that.
But I was asking more in general terms. If all we're doing is scanning, can we just change the mac? Anyway, not important. Maybe I bring this up once this set is accepted.
Regards,
-Denis
Johannes Berg
maintainerRe: [PATCH 2/2] mac80211: Support LIVE_ADDRESS_CHANGE feature
Quoted 6 lines · Denis Kenzior
Right, so you're talking in the context of this implementation which performs a remove/add interface. You're right about that.
But I was asking more in general terms. If all we're doing is scanning, can we just change the mac? Anyway, not important. Maybe I bring this up once this set is accepted.
Maybe, but honestly, I'm not convinced the complexity would be worth it. You'd have to push this all the way through to the driver, so it knows to do it, or defer it until the scan is done, or something? Not something you'd want to do on all hardware while a non-randomized scan is running, for example (iwlwifi might actually be OK).
Or you could perhaps cache the MAC address change in mac80211 and apply it at the next possible point in time - but then again you have to be really careful to actually apply it and block all further operations, even if a bunch of remain-on-channel's are active and you request a new scan, that has to be blocked until the remain-on-channel is done *and* the MAC address change is applied?
Seems rather complex for very little value.
johannes
Johannes Berg
maintainerRe: [PATCH 2/2] mac80211: Support LIVE_ADDRESS_CHANGE feature
In reply to James PrestwoodQuoted 8 lines · James Prestwood
Quoted 5 lines
I'm not even entirely sure it _is_ needed - if we've still not created
the IBSS but are scanning for it or trying to merge the MAC address won't really matter yet? Probably?I guess its just paranoia, rather be safe than sorry. I can take this out, but is "Probably?" a good reason? ;)
Fair enough, nobody really cares about IBSS anyway ;-)
I guess I was mostly wondering if you had noticed anything that would actually be a problem.
Quoted 2 lines
Ok so no switch statement, simply just check that we aren't offchannel or scanning. I guess this would then cover the IBSS case too.
Don't think it covers IBSS - that one is really specially accessing some IBSS data.
Quoted 10 lines
Quoted 4 lines
If you do care about this being more granular then you should check *which* interface is scanning, and then you can still switch the MAC address for *other* interfaces - but I'd still argue it should be independent of interface type.
I think maybe in the future we might want this, but for now lets not worry about it. But just to make sure we are on the same page, your talking about e.g. hardware with multiple radios so you could be doing offchannel work/scanning/connecting simultaneously without having to wait for the current operation to complete?
Not really multiple radios, who cares? Just multiple interfaces would be sufficient. You're just removing/adding some interface (as far as the driver is concerned) - doesn't matter if you actually are scanning or something on another interface right?
Quoted 7 lines
Quoted 2 lines
And, I'm confused, but isn't the polarity of the scanning check wrong?
Ah yeah, after you pointed that out I realized 'scanning' is a bit field. I should be doing:
test_bit(SCAN_HW_SCANNING, &sdata->local->scanning)
I think checking for all the bits is fine (and necessary, just HW scan is unlikely to be enough, changing the MAC address would also disrupt a software scan) - just need to invert the polarity?
Quoted 1 line
Either way I'll send another patch with these things addressed.
I'll wait, thanks.
johannes
Re: [PATCH 2/2] mac80211: Support LIVE_ADDRESS_CHANGE feature
Hi Johannes,
Quoted 11 lines
Quoted 7 lines
Quoted 2 lines
And, I'm confused, but isn't the polarity of the scanning check wrong?
Ah yeah, after you pointed that out I realized 'scanning' is a bit field. I should be doing:
test_bit(SCAN_HW_SCANNING, &sdata->local->scanning)I think checking for all the bits is fine (and necessary, just HW scan is unlikely to be enough, changing the MAC address would also disrupt a software scan) - just need to invert the polarity?
I concur that scanning should be checked as
if (sdata->local->scanning). So Johannes you're right that the polarity is reversed. However, __ieee80211_start_scan seems to check for local->scan_req instead to take deferred scans into account. So I wonder if that is a better approach.
Regards,
-Denis
Johannes Berg
maintainerRe: [PATCH 2/2] mac80211: Support LIVE_ADDRESS_CHANGE feature
Hi,
Quoted 5 lines
I concur that scanning should be checked as
if (sdata->local->scanning). So Johannes you're right that the polarity is reversed. However,__ieee80211_start_scanseems to check forlocal->scan_reqinstead to take deferred scans into account. So I wonder if that is a better approach.
Hmm. I don't think it's necessary.
We basically only get to that kind of state if ieee80211_can_scan() returned false - then we assign local->scan_req and defer until ieee80211_run_deferred_scan() is called.
But in the meantime, nothing in the scan requests references the MAC address.
It does mean that we should grab local->mtx though for these checks, and then all around the interface change, so that we can be sure we don't actually start scanning in the middle of the changes here.
johannes
Johannes Berg
maintainerQuoted 8 lines · James Prestwood
Add a new feature bit signifying that the wireless hardware supports changing the mac address while the underlying
net_deviceis UP. Note that this is slightly different fromIFF_LIVE_ADDR_CHANGEas additional restrictions might be imposed by the hardware. Typical restrictions are:
- No connection is active on this interface, e.g. carrier is off
- No scan is in progress
- No offchannel operation is in progress
Hmm, what do you need this patch for?
IFF_LIVE_ADDR_CHANGE should be sufficient to discover it?
johannes
Hi,
Quoted 15 lines · Johannes Berg
Quoted 5 lines · James Prestwood
Add a new feature bit signifying that the wireless hardware supports
changing the mac address while the underlyingnet_deviceis UP. Note
that this is slightly different fromIFF_LIVE_ADDR_CHANGEasQuoted 8 lines
additional
restrictions might be imposed by the hardware. Typical restrictions
are:
- No connection is active on this interface, e.g. carrier is
off
- No scan is in progress
- No offchannel operation is in progress
Quoted 3 lines
Hmm, what do you need this patch for?
IFF_LIVE_ADDR_CHANGEshould be sufficient to discover it?
Because userspace needs to know if this is supported? IFF_LIVE_ADDR_CHANGE is a private flag... AFAIK userspace has no way of obtaining this.
Thanks,
James
Quoted 3 lines
johannes
Johannes Berg
maintainerQuoted 18 lines · James Prestwood
Hi,
Quoted 15 lines · Johannes Berg
Quoted 13 lines · James Prestwood
Add a new feature bit signifying that the wireless hardware supports
changing the mac address while the underlyingnet_deviceis UP. Note
that this is slightly different fromIFF_LIVE_ADDR_CHANGEas additional
restrictions might be imposed by the hardware. Typical restrictions
are:
- No connection is active on this interface, e.g. carrier is
off
- No scan is in progress
- No offchannel operation is in progress
Quoted 7 lines
Quoted 3 lines
Hmm, what do you need this patch for?
IFF_LIVE_ADDR_CHANGEshould be sufficient to discover it?Because userspace needs to know if this is supported?
IFF_LIVE_ADDR_CHANGEis a private flag... AFAIK userspace has no way of obtaining this.
Oh, annoying.
But that doesn't really mean that nl80211 is an appropriate place to advertise it, IMHO?
And in nl80211 you'd need the flag for if you actually have the "change MAC address during connect" attribute.
johannes
Quoted 29 lines · Johannes Berg
Quoted 19 lines · James Prestwood
Hi,
Quoted 16 lines · Johannes Berg
Quoted 14 lines · James Prestwood
Add a new feature bit signifying that the wireless hardware supports
changing the mac address while the underlyingnet_deviceis UP. Note
that this is slightly different fromIFF_LIVE_ADDR_CHANGEas additional
restrictions might be imposed by the hardware. Typical restrictions
are:
- No connection is active on this interface, e.g.
carrier is
off
- No scan is in progress
- No offchannel operation is in progressQuoted 8 lines
Quoted 3 lines
Hmm, what do you need this patch for?
IFF_LIVE_ADDR_CHANGEshould be sufficient to discover it?Because userspace needs to know if this is supported?
IFF_LIVE_ADDR_CHANGEis a private flag... AFAIK userspace has no way of
obtaining this.
Quoted 4 lines
Oh, annoying.
But that doesn't really mean that nl80211 is an appropriate place to advertise it, IMHO?
The intention of the flag was not soley related to CMD_CONNECT/CMD_AUTHENTICATE. Its an indication that the hardware/driver supports a live address change. If you don't want it here could you suggest a better location for it?
Quoted 7 lines
And in nl80211 you'd need the flag for if you actually have the "change
MAC address during connect" attribute.johannes
Johannes,
Quoted 32 lines · James Prestwood
Quoted 31 lines · Johannes Berg
Quoted 19 lines · James Prestwood
Hi,
Quoted 16 lines · Johannes Berg
Quoted 14 lines · James Prestwood
Add a new feature bit signifying that the wireless hardware supports
changing the mac address while the underlyingnet_deviceis UP. Note
that this is slightly different fromIFF_LIVE_ADDR_CHANGEas additional
restrictions might be imposed by the hardware. Typical restrictions
are:
- No connection is active on this interface, e.g.
carrier is
off
- No scan is in progress
- No offchannel operation is in progressQuoted 8 lines
Quoted 3 lines
Hmm, what do you need this patch for?
IFF_LIVE_ADDR_CHANGEshould be sufficient to discover it?Because userspace needs to know if this is supported?
IFF_LIVE_ADDR_CHANGEis a private flag... AFAIK userspace has no way of
obtaining this.Oh, annoying.
Quoted 8 lines
Quoted 3 lines
But that doesn't really mean that nl80211 is an appropriate place to
advertise it, IMHO?The intention of the flag was not soley related to CMD_CONNECT/CMD_AUTHENTICATE. Its an indication that the hardware/driver supports a live address change. If you don't want it here could you suggest a better location for it?
Could we continue this discussion? Is there some other way you can think of to let userspace know that this feature is supported rather than an ext feature?
Thanks,
James
Quoted 10 lines
Quoted 8 lines
And in nl80211 you'd need the flag for if you actually have the "change
MAC address during connect" attribute.johannes
Johannes Berg
maintainerHi,
Quoted 7 lines
Quoted 7 lines
Quoted 4 lines
Because userspace needs to know if this is supported?
IFF_LIVE_ADDR_CHANGEis a private flag... AFAIK userspace has no way of
obtaining this.Oh, annoying.
Quoted 7 lines
Quoted 2 lines
But that doesn't really mean that nl80211 is an appropriate place to advertise it, IMHO?
The intention of the flag was not soley related to CMD_CONNECT/CMD_AUTHENTICATE. Its an indication that the hardware/driver supports a live address change. If you don't want it here could you suggest a better location for it?
I guess RTNL would be the right place? This can hardly be specific to wireless, the flag comes from elsewhere.
johannes
Hi Johannes,
Quoted 14 lines · Johannes Berg
Hi,
Quoted 12 lines
Quoted 11 lines
Quoted 5 lines
Because userspace needs to know if this is supported?
IFF_LIVE_ADDR_CHANGEis a private flag... AFAIK userspace has no
way of
obtaining this.Oh, annoying.
But that doesn't really mean that nl80211 is an appropriate place to
advertise it, IMHO?
Quoted 8 lines
Quoted 5 lines
The intention of the flag was not soley related to CMD_CONNECT/CMD_AUTHENTICATE. Its an indication that the hardware/driver supports a live address change. If you don't want it
here could you suggest a better location for it?I guess RTNL would be the right place? This can hardly be specific to wireless, the flag comes from elsewhere.
I do see where your coming from, and maybe the answer is both RTNL and NL80211?
In this context a NL80211 flag would mean something different than only putting a flag into RTNL.
The NL80211 flag means this device supports changing the MAC while running and not offchannel/scanning. Which is what -EBUSY would mean in this context. Managing the offchannel/scanning work is only possible with a NL80211 application.
An RTNL only application has no idea about scanning/offchannel work, so it has no way of knowing what -EBUSY means in the wireless device context, or a way to prevent this from happening (stopping scanning or offchannel before changing the MAC).
Now, another example would be an RTNL application that only cares about non-wireless devices (like ethernet), and in this case it could benefit from some type of RTNL specific flag and not care about a NL80211 flag.
Since there is no such application that cares about this RTNL flag (since it doesn't exist) I would say that adding NL80211 flag is the way to go. If someone wants to add an RTNL flag I would say that is appropriate too. But in terms of this feature, a NL80211 flag is really what fits best since the changes are wireless specific.
Thanks,
James
Quoted 3 lines
johannes