Skip to contentSkip to conversation

Odroid n2 using eMMC would fail to boot up

PATCH New Anand Moon 3 participants 24 messages Feb 9, 2020 – Feb 13, 2020

Subsystems (3)
lore
Share & tools
lore

Anand Moon

author
#0 lore raw

v6 cover Odroid n2 using eMMC would fail to boot up

Here are some small changes to fix booting of Odroid N2 using eMMC. Fixed the clk tunnig during mmc initialization.
Added two new patches to fix warning

Build and tested on top of below patches
[0] https://patchwork.ozlabs.org/patch/1213648/
[1] https://patchwork.ozlabs.org/patch/1213650/

Tested on below eMMC module on Odroid N2 and C2
new orange - eMMC AJNB4R 14.6 GiB MMC 5.1
old back - eMMC CGND3R 58.2 GiB MMC 5.0

Prevoius changes:
Fixed the clk tuning as per mainline kernel

[3]v1 https://patchwork.ozlabs.org/cover/1201206/
[4]v2 https://patchwork.ozlabs.org/cover/1215217/
[5]v3 https://www.mail-archive.com/u-boot at lists.denx.de/msg351859.html [6]v4 https://patchwork.ozlabs.org/cover/1227205/
[7]v5 https://patchwork.ozlabs.org/cover/1232879/

-Anand

Anand Moon (5):
mmc: meson-gx: Fix clk phase tuning for MMC
mmc: meson-gx: Use proper compatible string as per the dts
arm: dts: gx: Move common nodes to the -u-boot.dtsi
arm: dts: g12: Move common nodes to the -u-boot.dtsi
arm: dts: s400: Move common nodes to the -u-boot.dtsi

 arch/arm/dts/meson-axg-s400-u-boot.dtsi       | 16 +++++
 arch/arm/dts/meson-axg-s400.dts               |  9 ---
 arch/arm/dts/meson-g12-common-u-boot.dtsi     | 12 ++++
 arch/arm/dts/meson-g12a-sei510.dts            |  9 ---
 arch/arm/dts/meson-g12a-u200.dts              |  9 ---
 arch/arm/dts/meson-g12b-odroid-n2.dts         |  9 ---
 arch/arm/dts/meson-gx-u-boot.dtsi             | 15 +++++
 arch/arm/dts/meson-gxbb-nanopi-k2.dts         |  9 ---
 arch/arm/dts/meson-gxbb-odroidc2.dts          |  9 ---
 arch/arm/dts/meson-gxbb-p20x.dtsi             |  9 ---
 arch/arm/dts/meson-gxl-s805x-libretech-ac.dts | 10 ----
 arch/arm/dts/meson-gxl-s905x-khadas-vim.dts   |  5 --
 arch/arm/dts/meson-gxl-s905x-libretech-cc.dts |  9 ---
 arch/arm/dts/meson-gxl-s905x-p212.dtsi        | 10 ----
 arch/arm/dts/meson-gxm-khadas-vim2.dts        | 10 ----
 arch/arm/dts/meson-khadas-vim3.dtsi           |  9 ---
 arch/arm/dts/meson-sm1-sei610.dts             |  9 ---
 arch/arm/include/asm/arch-meson/sd_emmc.h     | 31 +++++++---
 drivers/mmc/meson_gx_mmc.c                    | 58 ++++++++++++++++---
 19 files changed, 114 insertions(+), 143 deletions(-)
Signature · 1 line
2.25.0
author
#1 lore raw

PATCH v6 1/5 mmc: meson-gx: Fix clk phase tuning for MMC

As per mainline line kernel fix the clk tuning phase for mmc, set Core=180, Tx=0, Rx=0 clk phase for mmc initialization. As per S905, S905X, AGX and S922X datasheet set the default values for clk tuning.

---
Changes from previous
v5 Fix the commit message, configure as per mainline kernel.
drop the RX_DELAY_MASK and TX_DELAY_MASK as they are not used.

v4 Fix the update mask value using FIELD_PREP macro.

v3 Fix the initialization of core clk tunning phase as per datasheet.
Fix the commit message.

v2: Fix the clk phase macro to support PHASE_180
drop the wrong CLK_CORE_PHASE_MASK macro.

v1: use the mainline kernel tuning for clk tuning.

Fixed the commmit messages.
Patch v1:
https://patchwork.ozlabs.org/patch/1201208/

Before these changes.

    clock is enabled (380953Hz)
    clock is enabled (25000000Hz)
After these changes
    clock is enabled (380953Hz)
    clock is enabled (25000000Hz)
    clock is enabled (52000000Hz)
Test on Odroid N2 and Odroid C2 with eMMC and microSD cards
---
 arch/arm/include/asm/arch-meson/sd_emmc.h | 24 +++++++++++--------
 drivers/mmc/meson_gx_mmc.c                | 28 +++++++++++++++++++----
 2 files changed, 38 insertions(+), 14 deletions(-)
arch/arm/include/asm/arch-meson/sd_emmc.h +15 -9
index e3a72c8b66..f4299485dc 100644
@@ -7,6 +7,7 @@
 #define __SD_EMMC_H__
 
 #include <mmc.h>
+#include <linux/bitops.h>
 
 #define SDIO_PORT_A			0
 #define SDIO_PORT_B			1
@@ -19,15 +20,20 @@
 #define   CLK_MAX_DIV			63
 #define   CLK_SRC_24M			(0 << 6)
 #define   CLK_SRC_DIV2			(1 << 6)
-#define   CLK_CO_PHASE_000		(0 << 8)
-#define   CLK_CO_PHASE_090		(1 << 8)
-#define   CLK_CO_PHASE_180		(2 << 8)
-#define   CLK_CO_PHASE_270		(3 << 8)
-#define   CLK_TX_PHASE_000		(0 << 10)
-#define   CLK_TX_PHASE_090		(1 << 10)
-#define   CLK_TX_PHASE_180		(2 << 10)
-#define   CLK_TX_PHASE_270		(3 << 10)
-#define   CLK_ALWAYS_ON			BIT(24)
+
+#define   CRYSTAL_24MHZ			0
+#define   CLK_PHASE_0			0
+#define   CLK_PHASE_180			2
+
+#define   CLK_DIV_MASK			GENMASK(5, 0)
+#define   CLK_SRC_MASK			GENMASK(7, 6)
+#define   CLK_CORE_PHASE_MASK		GENMASK(9, 8)
+#define   CLK_TX_PHASE_MASK		GENMASK(11, 10)
+#define   CLK_RX_PHASE_MASK		GENMASK(13, 12)
+
+#define   CLK_V2_ALWAYS_ON		BIT(24)
+
+#define   CLK_V3_ALWAYS_ON		BIT(28)
 
 #define MESON_SD_EMMC_CFG		0x44
 #define   CFG_BUS_WIDTH_MASK		GENMASK(1, 0)
drivers/mmc/meson_gx_mmc.c +23 -5
index 86c1a7164a..b013c7c5fb 100644
@@ -16,6 +16,10 @@
 #include <asm/arch/sd_emmc.h>
 #include <linux/log2.h>
 
+#include <linux/bitops.h>
+#include <linux/compat.h>
+#include <linux/bitfield.h>
+
 static inline void *get_regbase(const struct mmc *mmc)
 {
 	struct meson_mmc_platdata *pdata = mmc->priv;
@@ -51,11 +55,25 @@ static void meson_mmc_config_clock(struct mmc *mmc)
 	}
 	clk_div = DIV_ROUND_UP(clk, mmc->clock);
 
-	/* 180 phase core clock */
-	meson_mmc_clk |= CLK_CO_PHASE_180;
-
-	/* 180 phase tx clock */
-	meson_mmc_clk |= CLK_TX_PHASE_000;
+	/* Clock divider */
+	meson_mmc_clk |= CLK_DIV_MASK;
+	/* Clock source : Crystal 24MHz */
+	meson_mmc_clk |= FIELD_PREP(CLK_SRC_MASK, CRYSTAL_24MHZ);
+	/* Core clock phase 2:180 */
+	meson_mmc_clk |= FIELD_PREP(CLK_CORE_PHASE_MASK, CLK_PHASE_180);
+	/* TX clock phase 0:180 */
+	meson_mmc_clk |= FIELD_PREP(CLK_TX_PHASE_MASK, CLK_PHASE_0);
+	/* RX clock phase 0:180 */
+	meson_mmc_clk |= FIELD_PREP(CLK_RX_PHASE_MASK, CLK_PHASE_0);
+
+#ifdef CONFIG_MESON_GX
+	/* clk always on */
+	meson_mmc_clk |= CLK_V2_ALWAYS_ON;
+#endif
+#if (defined(CONFIG_MESON_AXG) || defined(CONFIG_MESON_G12A))
+	/* clk always on */
+	meson_mmc_clk |= CLK_V3_ALWAYS_ON;
+#endif
 
 	/* clock settings */
 	meson_mmc_clk |= clk_src;
Signature · 1 line
2.25.0
#2 lore raw

PATCH v6 1/5 mmc: meson-gx: Fix clk phase tuning for MMC

Hi,

Quoted 96 lines · Anand Moon

As per mainline line kernel fix the clk tuning phase for mmc, set Core=180, Tx=0, Rx=0 clk phase for mmc initialization. As per S905, S905X, AGX and S922X datasheet set the default values for clk tuning.

---
Changes from previous
v5 Fix the commit message, configure as per mainline kernel.
drop the RX_DELAY_MASK and TX_DELAY_MASK as they are not used.

v4 Fix the update mask value using FIELD_PREP macro.

v3 Fix the initialization of core clk tunning phase as per datasheet.
Fix the commit message.

v2: Fix the clk phase macro to support PHASE_180
drop the wrong CLK_CORE_PHASE_MASK macro.

v1: use the mainline kernel tuning for clk tuning.

Fixed the commmit messages.
Patch v1:
https://patchwork.ozlabs.org/patch/1201208/

Before these changes.

    clock is enabled (380953Hz)
    clock is enabled (25000000Hz)
After these changes
    clock is enabled (380953Hz)
    clock is enabled (25000000Hz)
    clock is enabled (52000000Hz)
Test on Odroid N2 and Odroid C2 with eMMC and microSD cards
---
 arch/arm/include/asm/arch-meson/sd_emmc.h | 24 +++++++++++--------
 drivers/mmc/meson_gx_mmc.c                | 28 +++++++++++++++++++----
 2 files changed, 38 insertions(+), 14 deletions(-)
arch/arm/include/asm/arch-meson/sd_emmc.h +15 -9
index e3a72c8b66..f4299485dc 100644
@@ -7,6 +7,7 @@
 #define __SD_EMMC_H__
 
 #include <mmc.h>
+#include <linux/bitops.h>
 
 #define SDIO_PORT_A			0
 #define SDIO_PORT_B			1
@@ -19,15 +20,20 @@
 #define   CLK_MAX_DIV			63
 #define   CLK_SRC_24M			(0 << 6)
 #define   CLK_SRC_DIV2			(1 << 6)
-#define   CLK_CO_PHASE_000		(0 << 8)
-#define   CLK_CO_PHASE_090		(1 << 8)
-#define   CLK_CO_PHASE_180		(2 << 8)
-#define   CLK_CO_PHASE_270		(3 << 8)
-#define   CLK_TX_PHASE_000		(0 << 10)
-#define   CLK_TX_PHASE_090		(1 << 10)
-#define   CLK_TX_PHASE_180		(2 << 10)
-#define   CLK_TX_PHASE_270		(3 << 10)
-#define   CLK_ALWAYS_ON			BIT(24)
+
+#define   CRYSTAL_24MHZ			0
+#define   CLK_PHASE_0			0
+#define   CLK_PHASE_180			2
+
+#define   CLK_DIV_MASK			GENMASK(5, 0)
+#define   CLK_SRC_MASK			GENMASK(7, 6)
+#define   CLK_CORE_PHASE_MASK		GENMASK(9, 8)
+#define   CLK_TX_PHASE_MASK		GENMASK(11, 10)
+#define   CLK_RX_PHASE_MASK		GENMASK(13, 12)
+
+#define   CLK_V2_ALWAYS_ON		BIT(24)
+
+#define   CLK_V3_ALWAYS_ON		BIT(28)
 
 #define MESON_SD_EMMC_CFG		0x44
 #define   CFG_BUS_WIDTH_MASK		GENMASK(1, 0)
drivers/mmc/meson_gx_mmc.c +4 -0
index 86c1a7164a..b013c7c5fb 100644
@@ -16,6 +16,10 @@
 #include <asm/arch/sd_emmc.h>
 #include <linux/log2.h>
 
+#include <linux/bitops.h>
+#include <linux/compat.h>
+#include <linux/bitfield.h>
+
 static inline void *get_regbase(const struct mmc *mmc)
 {
 	struct meson_mmc_platdata *pdata = mmc->priv;

drivers/mmc/meson_gx_mmc.c static void meson_mmc_config_clock(struct mmc *mmc) · line 59

Quoted 10 lines
drivers/mmc/meson_gx_mmc.c +2 -5
@@ -51,11 +55,25 @@ static void meson_mmc_config_clock(struct mmc *mmc)
 	}
 	clk_div = DIV_ROUND_UP(clk, mmc->clock);
 
-	/* 180 phase core clock */
-	meson_mmc_clk |= CLK_CO_PHASE_180;
-
-	/* 180 phase tx clock */
-	meson_mmc_clk |= CLK_TX_PHASE_000;
+	/* Clock divider */
+	meson_mmc_clk |= CLK_DIV_MASK;

This will set the max divider, whatever the value of clk_div, so the following statement:
meson_mmc_clk |= clk_div;
will have no effect.

drivers/mmc/meson_gx_mmc.c static void meson_mmc_config_clock(struct mmc *mmc) · line 61

Quoted 2 lines
drivers/mmc/meson_gx_mmc.c +2 -0
+	/* Clock source : Crystal 24MHz */
+	meson_mmc_clk |= FIELD_PREP(CLK_SRC_MASK, CRYSTAL_24MHZ);

You set CRYSTAL_24MHZ here, but the src is selected in clk_src and set with:
meson_mmc_clk |= clk_src;

In conclusion your change forces the 24MHz crystal and max divider whatever the freq asked by the mmc core !

drivers/mmc/meson_gx_mmc.c static void meson_mmc_config_clock(struct mmc *mmc) · line 67

Quoted 6 lines
drivers/mmc/meson_gx_mmc.c +6 -0
+	/* Core clock phase 2:180 */
+	meson_mmc_clk |= FIELD_PREP(CLK_CORE_PHASE_MASK, CLK_PHASE_180);
+	/* TX clock phase 0:180 */
+	meson_mmc_clk |= FIELD_PREP(CLK_TX_PHASE_MASK, CLK_PHASE_0);
+	/* RX clock phase 0:180 */
+	meson_mmc_clk |= FIELD_PREP(CLK_RX_PHASE_MASK, CLK_PHASE_0);

These are ok, but it's exactly the same as before with a different style.

drivers/mmc/meson_gx_mmc.c static void meson_mmc_config_clock(struct mmc *mmc) · line 76

Quoted 9 lines
drivers/mmc/meson_gx_mmc.c +9 -0
+
+#ifdef CONFIG_MESON_GX
+	/* clk always on */
+	meson_mmc_clk |= CLK_V2_ALWAYS_ON;
+#endif
+#if (defined(CONFIG_MESON_AXG) || defined(CONFIG_MESON_G12A))
+	/* clk always on */
+	meson_mmc_clk |= CLK_V3_ALWAYS_ON;
+#endif

Why not, not sure about the effect.

drivers/mmc/meson_gx_mmc.c static void meson_mmc_config_clock(struct mmc *mmc)

Quoted 4 lines
drivers/mmc/meson_gx_mmc.c +0 -0
 	/* clock settings */
 	meson_mmc_clk |= clk_src;
 

Neil

author
#3 lore raw

PATCH v6 1/5 mmc: meson-gx: Fix clk phase tuning for MMC

Hi Neil,

Thanks for you review comments.

Quoted 103 lines · Neil Armstrong

Hi,

Quoted 99 lines · Anand Moon

As per mainline line kernel fix the clk tuning phase for mmc, set Core=180, Tx=0, Rx=0 clk phase for mmc initialization. As per S905, S905X, AGX and S922X datasheet set the default values for clk tuning.

---
Changes from previous
v5 Fix the commit message, configure as per mainline kernel.
drop the RX_DELAY_MASK and TX_DELAY_MASK as they are not used.

v4 Fix the update mask value using FIELD_PREP macro.

v3 Fix the initialization of core clk tunning phase as per datasheet.
Fix the commit message.

v2: Fix the clk phase macro to support PHASE_180
drop the wrong CLK_CORE_PHASE_MASK macro.

v1: use the mainline kernel tuning for clk tuning.

Fixed the commmit messages.
Patch v1:
https://patchwork.ozlabs.org/patch/1201208/

Before these changes.

    clock is enabled (380953Hz)
    clock is enabled (25000000Hz)
After these changes
    clock is enabled (380953Hz)
    clock is enabled (25000000Hz)
    clock is enabled (52000000Hz)
Test on Odroid N2 and Odroid C2 with eMMC and microSD cards
---
 arch/arm/include/asm/arch-meson/sd_emmc.h | 24 +++++++++++--------
 drivers/mmc/meson_gx_mmc.c                | 28 +++++++++++++++++++----
 2 files changed, 38 insertions(+), 14 deletions(-)
arch/arm/include/asm/arch-meson/sd_emmc.h +15 -9
index e3a72c8b66..f4299485dc 100644
@@ -7,6 +7,7 @@
 #define __SD_EMMC_H__
 
 #include <mmc.h>
+#include <linux/bitops.h>
 
 #define SDIO_PORT_A                  0
 #define SDIO_PORT_B                  1
@@ -19,15 +20,20 @@
 #define   CLK_MAX_DIV                        63
 #define   CLK_SRC_24M                        (0 << 6)
 #define   CLK_SRC_DIV2                       (1 << 6)
-#define   CLK_CO_PHASE_000           (0 << 8)
-#define   CLK_CO_PHASE_090           (1 << 8)
-#define   CLK_CO_PHASE_180           (2 << 8)
-#define   CLK_CO_PHASE_270           (3 << 8)
-#define   CLK_TX_PHASE_000           (0 << 10)
-#define   CLK_TX_PHASE_090           (1 << 10)
-#define   CLK_TX_PHASE_180           (2 << 10)
-#define   CLK_TX_PHASE_270           (3 << 10)
-#define   CLK_ALWAYS_ON                      BIT(24)
+
+#define   CRYSTAL_24MHZ                      0
+#define   CLK_PHASE_0                        0
+#define   CLK_PHASE_180                      2
+
+#define   CLK_DIV_MASK                       GENMASK(5, 0)
+#define   CLK_SRC_MASK                       GENMASK(7, 6)
+#define   CLK_CORE_PHASE_MASK                GENMASK(9, 8)
+#define   CLK_TX_PHASE_MASK          GENMASK(11, 10)
+#define   CLK_RX_PHASE_MASK          GENMASK(13, 12)
+
+#define   CLK_V2_ALWAYS_ON           BIT(24)
+
+#define   CLK_V3_ALWAYS_ON           BIT(28)
 
 #define MESON_SD_EMMC_CFG            0x44
 #define   CFG_BUS_WIDTH_MASK         GENMASK(1, 0)
drivers/mmc/meson_gx_mmc.c +4 -0
index 86c1a7164a..b013c7c5fb 100644
@@ -16,6 +16,10 @@
 #include <asm/arch/sd_emmc.h>
 #include <linux/log2.h>
 
+#include <linux/bitops.h>
+#include <linux/compat.h>
+#include <linux/bitfield.h>
+
 static inline void *get_regbase(const struct mmc *mmc)
 {
      struct meson_mmc_platdata *pdata = mmc->priv;
@@ -51,11 +55,25 @@ static void meson_mmc_config_clock(struct mmc *mmc)
      }
      clk_div = DIV_ROUND_UP(clk, mmc->clock);
 
Quoted 11 lines

drivers/mmc/meson_gx_mmc.c static void meson_mmc_config_clock(struct mmc *mmc) · line 59

Quoted 7 lines
drivers/mmc/meson_gx_mmc.c +2 -5
-     /* 180 phase core clock */
-     meson_mmc_clk |= CLK_CO_PHASE_180;
-
-     /* 180 phase tx clock */
-     meson_mmc_clk |= CLK_TX_PHASE_000;
+     /* Clock divider */
+     meson_mmc_clk |= CLK_DIV_MASK;

This will set the max divider, whatever the value of clk_div, so the following statement:
meson_mmc_clk |= clk_div;
will have no effect.

As per the datasheet S905 and S922X max divider is 63.
CLK_DIV_MASK[0-5] Cfg_div: Clock divider
Frequency = clock source/cfg_div Clock off: cfg_div==0, the
clock is disabled

                                        Divider bypass: cfg_div==1,

clock source is used as core clock without divider
Maximum divider 63

So here is the log of clk_div and clk_freq at my end.

MMC Device 0 not found
no mmc device at slot 0
clock is disabled (0Hz)
clock is enabled (380953Hz)
......clk_div : 63
Card did not respond to voltage select!
clock is disabled (0Hz)
clock is enabled (380953Hz)
......clk_div : 63
clock is enabled (25000000Hz)
......clk_div : 40
......clk_div : 40
clock is enabled (52000000Hz)
......clk_div : 20
switch to partitions #0, OK
mmc2(part 0) is current device
Scanning mmc 2:1...
Found U-Boot script /boot/boot.scr

Quoted 11 lines

drivers/mmc/meson_gx_mmc.c static void meson_mmc_config_clock(struct mmc *mmc) · line 61

Quoted 4 lines
drivers/mmc/meson_gx_mmc.c +2 -0
+     /* Clock source : Crystal 24MHz */
+     meson_mmc_clk |= FIELD_PREP(CLK_SRC_MASK, CRYSTAL_24MHZ);

You set CRYSTAL_24MHZ here, but the src is selected in clk_src and set with:
meson_mmc_clk |= clk_src;

In conclusion your change forces the 24MHz crystal and max divider whatever the freq asked by the mmc core !

As per the datasheet S905 and S922X
Cfg_src: Clock source
0: Crystal 24MHz or other frequencies
selected by clock reset test control register.
1: Fix PLL, 1000MHz Recommended value: 1

Note: *setting cfg_src value to I i.e; Fix PLL 1000 Mhz *
some how break the clk_freq tuning setting in my testing, see the logs below.

MMC Device 0 not found
no mmc device at slot 0
clock is disabled (0Hz)
clock is enabled (380953Hz)
......clk_div : 63
Card did not respond to voltage select!
clock is disabled (0Hz)
clock is enabled (380953Hz)
......clk_div : 63
starting USB...

No emmc will get discovered,
*This is the real issue I faced for failure of eMMC not getting detected.*

Quoted 9 lines

drivers/mmc/meson_gx_mmc.c static void meson_mmc_config_clock(struct mmc *mmc) · line 67

Quoted 6 lines
drivers/mmc/meson_gx_mmc.c +6 -0
+     /* Core clock phase 2:180 */
+     meson_mmc_clk |= FIELD_PREP(CLK_CORE_PHASE_MASK, CLK_PHASE_180);
+     /* TX clock phase 0:180 */
+     meson_mmc_clk |= FIELD_PREP(CLK_TX_PHASE_MASK, CLK_PHASE_0);
+     /* RX clock phase 0:180 */
+     meson_mmc_clk |= FIELD_PREP(CLK_RX_PHASE_MASK, CLK_PHASE_0);

These are ok, but it's exactly the same as before with a different style.

Quoted 11 lines

drivers/mmc/meson_gx_mmc.c static void meson_mmc_config_clock(struct mmc *mmc) · line 76

Quoted 9 lines
drivers/mmc/meson_gx_mmc.c +9 -0
+
+#ifdef CONFIG_MESON_GX
+     /* clk always on */
+     meson_mmc_clk |= CLK_V2_ALWAYS_ON;
+#endif
+#if (defined(CONFIG_MESON_AXG) || defined(CONFIG_MESON_G12A))
+     /* clk always on */
+     meson_mmc_clk |= CLK_V3_ALWAYS_ON;
+#endif

Why not, not sure about the effect.

Ok, I will changes these to FIELD_PREP for consultancy.

Quoted 7 lines

drivers/mmc/meson_gx_mmc.c static void meson_mmc_config_clock(struct mmc *mmc)

Quoted 5 lines
drivers/mmc/meson_gx_mmc.c +0 -0
      /* clock settings */
      meson_mmc_clk |= clk_src;
 

Neil

-Anand

#4 lore raw

PATCH v6 1/5 mmc: meson-gx: Fix clk phase tuning for MMC

Quoted 141 lines · Anand Moon

Hi Neil,

Thanks for you review comments.

Quoted 103 lines · Neil Armstrong

Hi,

Quoted 99 lines · Anand Moon

As per mainline line kernel fix the clk tuning phase for mmc, set Core=180, Tx=0, Rx=0 clk phase for mmc initialization. As per S905, S905X, AGX and S922X datasheet set the default values for clk tuning.

---
Changes from previous
v5 Fix the commit message, configure as per mainline kernel.
drop the RX_DELAY_MASK and TX_DELAY_MASK as they are not used.

v4 Fix the update mask value using FIELD_PREP macro.

v3 Fix the initialization of core clk tunning phase as per datasheet.
Fix the commit message.

v2: Fix the clk phase macro to support PHASE_180
drop the wrong CLK_CORE_PHASE_MASK macro.

v1: use the mainline kernel tuning for clk tuning.

Fixed the commmit messages.
Patch v1:
https://patchwork.ozlabs.org/patch/1201208/

Before these changes.

    clock is enabled (380953Hz)
    clock is enabled (25000000Hz)
After these changes
    clock is enabled (380953Hz)
    clock is enabled (25000000Hz)
    clock is enabled (52000000Hz)
Test on Odroid N2 and Odroid C2 with eMMC and microSD cards
---
 arch/arm/include/asm/arch-meson/sd_emmc.h | 24 +++++++++++--------
 drivers/mmc/meson_gx_mmc.c                | 28 +++++++++++++++++++----
 2 files changed, 38 insertions(+), 14 deletions(-)
arch/arm/include/asm/arch-meson/sd_emmc.h +15 -9
index e3a72c8b66..f4299485dc 100644
@@ -7,6 +7,7 @@
 #define __SD_EMMC_H__
 
 #include <mmc.h>
+#include <linux/bitops.h>
 
 #define SDIO_PORT_A                  0
 #define SDIO_PORT_B                  1
@@ -19,15 +20,20 @@
 #define   CLK_MAX_DIV                        63
 #define   CLK_SRC_24M                        (0 << 6)
 #define   CLK_SRC_DIV2                       (1 << 6)
-#define   CLK_CO_PHASE_000           (0 << 8)
-#define   CLK_CO_PHASE_090           (1 << 8)
-#define   CLK_CO_PHASE_180           (2 << 8)
-#define   CLK_CO_PHASE_270           (3 << 8)
-#define   CLK_TX_PHASE_000           (0 << 10)
-#define   CLK_TX_PHASE_090           (1 << 10)
-#define   CLK_TX_PHASE_180           (2 << 10)
-#define   CLK_TX_PHASE_270           (3 << 10)
-#define   CLK_ALWAYS_ON                      BIT(24)
+
+#define   CRYSTAL_24MHZ                      0
+#define   CLK_PHASE_0                        0
+#define   CLK_PHASE_180                      2
+
+#define   CLK_DIV_MASK                       GENMASK(5, 0)
+#define   CLK_SRC_MASK                       GENMASK(7, 6)
+#define   CLK_CORE_PHASE_MASK                GENMASK(9, 8)
+#define   CLK_TX_PHASE_MASK          GENMASK(11, 10)
+#define   CLK_RX_PHASE_MASK          GENMASK(13, 12)
+
+#define   CLK_V2_ALWAYS_ON           BIT(24)
+
+#define   CLK_V3_ALWAYS_ON           BIT(28)
 
 #define MESON_SD_EMMC_CFG            0x44
 #define   CFG_BUS_WIDTH_MASK         GENMASK(1, 0)
drivers/mmc/meson_gx_mmc.c +4 -0
index 86c1a7164a..b013c7c5fb 100644
@@ -16,6 +16,10 @@
 #include <asm/arch/sd_emmc.h>
 #include <linux/log2.h>
 
+#include <linux/bitops.h>
+#include <linux/compat.h>
+#include <linux/bitfield.h>
+
 static inline void *get_regbase(const struct mmc *mmc)
 {
      struct meson_mmc_platdata *pdata = mmc->priv;
@@ -51,11 +55,25 @@ static void meson_mmc_config_clock(struct mmc *mmc)
      }
      clk_div = DIV_ROUND_UP(clk, mmc->clock);
 
Quoted 11 lines

drivers/mmc/meson_gx_mmc.c static void meson_mmc_config_clock(struct mmc *mmc) · line 59

Quoted 7 lines
drivers/mmc/meson_gx_mmc.c +2 -5
-     /* 180 phase core clock */
-     meson_mmc_clk |= CLK_CO_PHASE_180;
-
-     /* 180 phase tx clock */
-     meson_mmc_clk |= CLK_TX_PHASE_000;
+     /* Clock divider */
+     meson_mmc_clk |= CLK_DIV_MASK;

This will set the max divider, whatever the value of clk_div, so the following statement:
meson_mmc_clk |= clk_div;
will have no effect.

As per the datasheet S905 and S922X max divider is 63.
CLK_DIV_MASK[0-5] Cfg_div: Clock divider
Frequency = clock source/cfg_div Clock off: cfg_div==0, the
clock is disabled

                                        Divider bypass: cfg_div==1,

clock source is used as core clock without divider
Maximum divider 63

So here is the log of clk_div and clk_freq at my end.

MMC Device 0 not found
no mmc device at slot 0
clock is disabled (0Hz)
clock is enabled (380953Hz)
......clk_div : 63
Card did not respond to voltage select!
clock is disabled (0Hz)
clock is enabled (380953Hz)
......clk_div : 63
clock is enabled (25000000Hz)

Quoted 8 lines

......clk_div : 40
......clk_div : 40
clock is enabled (52000000Hz)
......clk_div : 20
switch to partitions #0, OK
mmc2(part 0) is current device
Scanning mmc 2:1...
Found U-Boot script /boot/boot.scr

OK, seems you didn't see the issue.

With the original code, let's say mmc->clock = 25000000

clk = SD_EMMC_CLKSRC_DIV2
clk_src = CLK_SRC_DIV2
clk_div = 40

meson_mmc_clk |= CLK_CO_PHASE_180;
meson_mmc_clk |= CLK_TX_PHASE_000;
meson_mmc_clk |= CLK_SRC_DIV2;
meson_mmc_clk |= 40;

=> meson_mmc_clk = (2 << 8) | (0 << 10) | (1 << 6) | 40 => meson_mmc_clk = 0x268

With your code :

meson_mmc_clk |= CLK_DIV_MASK;
meson_mmc_clk |= FIELD_PREP(CLK_SRC_MASK, CRYSTAL_24MHZ);
meson_mmc_clk |= FIELD_PREP(CLK_CORE_PHASE_MASK, CLK_PHASE_180);
meson_mmc_clk |= FIELD_PREP(CLK_TX_PHASE_MASK, CLK_PHASE_0);
meson_mmc_clk |= FIELD_PREP(CLK_RX_PHASE_MASK, CLK_PHASE_0);
meson_mmc_clk |= CLK_SRC_DIV2;
meson_mmc_clk |= 40;

=> meson_mmc_clk = 0x3f | (0 << 6) | (2 << 8) | (0 << 11) | (0 << 13) | (1 << 6) | 40

-------------------/\---this---------makes-------this-----useless------------------/\

=> 0x27f

It sets the clock to 15873015Hz instead of the 25000000Hz requested.

so this code sets max divider whatever mmc->clock value, but keeps the CRYSTAL_24MHZ/CLK_SRC_DIV2 selection.

Quoted 34 lines
Quoted 12 lines

drivers/mmc/meson_gx_mmc.c static void meson_mmc_config_clock(struct mmc *mmc) · line 61

Quoted 5 lines
drivers/mmc/meson_gx_mmc.c +2 -0
+     /* Clock source : Crystal 24MHz */
+     meson_mmc_clk |= FIELD_PREP(CLK_SRC_MASK, CRYSTAL_24MHZ);

You set CRYSTAL_24MHZ here, but the src is selected in clk_src and set with:
meson_mmc_clk |= clk_src;

In conclusion your change forces the 24MHz crystal and max divider whatever the freq asked by the mmc core !

As per the datasheet S905 and S922X
Cfg_src: Clock source
0: Crystal 24MHz or other frequencies
selected by clock reset test control register.
1: Fix PLL, 1000MHz Recommended value: 1

Note: *setting cfg_src value to I i.e; Fix PLL 1000 Mhz *
some how break the clk_freq tuning setting in my testing, see the logs below.

MMC Device 0 not found
no mmc device at slot 0
clock is disabled (0Hz)
clock is enabled (380953Hz)
......clk_div : 63
Card did not respond to voltage select!
clock is disabled (0Hz)
clock is enabled (380953Hz)
......clk_div : 63
starting USB...

Quoted 2 lines

No emmc will get discovered,
*This is the real issue I faced for failure of eMMC not getting detected.*

This is the issue I get on SM1, but when I cap the max freq to 24MHz, it disappears.

This issue is somewhere else, but I don't know where because the Linux driver behaves correctly with the same setup.

My fix was to always use the 24MHz crystal input on non-GX until we find out why, and it still acceptable.

Could you post instead :
- your patch 2 introducing the MMC_COMPATIBLE_* as patch 1
- this patch but only forcing 24MHz for MMC_COMPATIBLE_AXG as patch 2
- redude patches 3,4 & 5 to only add mmc* aliases into meson-gx-u-boot.dtsi/meson-g12-common-u-boot.dtsi

If you have a issue, please chat with me on #linux-amlogic on freenode.

Thanks,
Neil

Quoted 22 lines
Quoted 10 lines

drivers/mmc/meson_gx_mmc.c static void meson_mmc_config_clock(struct mmc *mmc) · line 67

Quoted 7 lines
drivers/mmc/meson_gx_mmc.c +6 -0
+     /* Core clock phase 2:180 */
+     meson_mmc_clk |= FIELD_PREP(CLK_CORE_PHASE_MASK, CLK_PHASE_180);
+     /* TX clock phase 0:180 */
+     meson_mmc_clk |= FIELD_PREP(CLK_TX_PHASE_MASK, CLK_PHASE_0);
+     /* RX clock phase 0:180 */
+     meson_mmc_clk |= FIELD_PREP(CLK_RX_PHASE_MASK, CLK_PHASE_0);

These are ok, but it's exactly the same as before with a different style.

Quoted 11 lines

drivers/mmc/meson_gx_mmc.c static void meson_mmc_config_clock(struct mmc *mmc) · line 76

Quoted 9 lines
drivers/mmc/meson_gx_mmc.c +9 -0
+
+#ifdef CONFIG_MESON_GX
+     /* clk always on */
+     meson_mmc_clk |= CLK_V2_ALWAYS_ON;
+#endif
+#if (defined(CONFIG_MESON_AXG) || defined(CONFIG_MESON_G12A))
+     /* clk always on */
+     meson_mmc_clk |= CLK_V3_ALWAYS_ON;
+#endif

Why not, not sure about the effect.

Quoted 1 line

Ok, I will changes these to FIELD_PREP for consultancy.

Really not sure about the effect of these, please drop these until we find out if we really need these.

Quoted 11 lines
Quoted 8 lines

drivers/mmc/meson_gx_mmc.c static void meson_mmc_config_clock(struct mmc *mmc)

Quoted 6 lines
drivers/mmc/meson_gx_mmc.c +0 -0
      /* clock settings */
      meson_mmc_clk |= clk_src;
 

Neil

-Anand

author
#5 lore raw

PATCH v6 1/5 mmc: meson-gx: Fix clk phase tuning for MMC

hi Niel / Jerome,

Thanks for your review comments and debug output
Sorry for late reply.

Quoted 178 lines · Neil Armstrong
Quoted 141 lines · Anand Moon

Hi Neil,

Thanks for you review comments.

Quoted 103 lines · Neil Armstrong

Hi,

Le 09/02/2020 ? 12:05, Anand Moon a ?crit :

Quoted 99 lines

As per mainline line kernel fix the clk tuning phase for mmc, set Core=180, Tx=0, Rx=0 clk phase for mmc initialization. As per S905, S905X, AGX and S922X datasheet set the default values for clk tuning.

---
Changes from previous
v5 Fix the commit message, configure as per mainline kernel.
drop the RX_DELAY_MASK and TX_DELAY_MASK as they are not used.

v4 Fix the update mask value using FIELD_PREP macro.

v3 Fix the initialization of core clk tunning phase as per datasheet.
Fix the commit message.

v2: Fix the clk phase macro to support PHASE_180
drop the wrong CLK_CORE_PHASE_MASK macro.

v1: use the mainline kernel tuning for clk tuning.

Fixed the commmit messages.
Patch v1:
https://patchwork.ozlabs.org/patch/1201208/

Before these changes.

    clock is enabled (380953Hz)
    clock is enabled (25000000Hz)
After these changes
    clock is enabled (380953Hz)
    clock is enabled (25000000Hz)
    clock is enabled (52000000Hz)
Test on Odroid N2 and Odroid C2 with eMMC and microSD cards
---
 arch/arm/include/asm/arch-meson/sd_emmc.h | 24 +++++++++++--------
 drivers/mmc/meson_gx_mmc.c                | 28 +++++++++++++++++++----
 2 files changed, 38 insertions(+), 14 deletions(-)
arch/arm/include/asm/arch-meson/sd_emmc.h +15 -9
index e3a72c8b66..f4299485dc 100644
@@ -7,6 +7,7 @@
 #define __SD_EMMC_H__
 
 #include <mmc.h>
+#include <linux/bitops.h>
 
 #define SDIO_PORT_A                  0
 #define SDIO_PORT_B                  1
@@ -19,15 +20,20 @@
 #define   CLK_MAX_DIV                        63
 #define   CLK_SRC_24M                        (0 << 6)
 #define   CLK_SRC_DIV2                       (1 << 6)
-#define   CLK_CO_PHASE_000           (0 << 8)
-#define   CLK_CO_PHASE_090           (1 << 8)
-#define   CLK_CO_PHASE_180           (2 << 8)
-#define   CLK_CO_PHASE_270           (3 << 8)
-#define   CLK_TX_PHASE_000           (0 << 10)
-#define   CLK_TX_PHASE_090           (1 << 10)
-#define   CLK_TX_PHASE_180           (2 << 10)
-#define   CLK_TX_PHASE_270           (3 << 10)
-#define   CLK_ALWAYS_ON                      BIT(24)
+
+#define   CRYSTAL_24MHZ                      0
+#define   CLK_PHASE_0                        0
+#define   CLK_PHASE_180                      2
+
+#define   CLK_DIV_MASK                       GENMASK(5, 0)
+#define   CLK_SRC_MASK                       GENMASK(7, 6)
+#define   CLK_CORE_PHASE_MASK                GENMASK(9, 8)
+#define   CLK_TX_PHASE_MASK          GENMASK(11, 10)
+#define   CLK_RX_PHASE_MASK          GENMASK(13, 12)
+
+#define   CLK_V2_ALWAYS_ON           BIT(24)
+
+#define   CLK_V3_ALWAYS_ON           BIT(28)
 
 #define MESON_SD_EMMC_CFG            0x44
 #define   CFG_BUS_WIDTH_MASK         GENMASK(1, 0)
drivers/mmc/meson_gx_mmc.c +4 -0
index 86c1a7164a..b013c7c5fb 100644
@@ -16,6 +16,10 @@
 #include <asm/arch/sd_emmc.h>
 #include <linux/log2.h>
 
+#include <linux/bitops.h>
+#include <linux/compat.h>
+#include <linux/bitfield.h>
+
 static inline void *get_regbase(const struct mmc *mmc)
 {
      struct meson_mmc_platdata *pdata = mmc->priv;
@@ -51,11 +55,25 @@ static void meson_mmc_config_clock(struct mmc *mmc)
      }
      clk_div = DIV_ROUND_UP(clk, mmc->clock);
 
Quoted 11 lines

drivers/mmc/meson_gx_mmc.c static void meson_mmc_config_clock(struct mmc *mmc) · line 59

Quoted 7 lines
drivers/mmc/meson_gx_mmc.c +2 -5
-     /* 180 phase core clock */
-     meson_mmc_clk |= CLK_CO_PHASE_180;
-
-     /* 180 phase tx clock */
-     meson_mmc_clk |= CLK_TX_PHASE_000;
+     /* Clock divider */
+     meson_mmc_clk |= CLK_DIV_MASK;

This will set the max divider, whatever the value of clk_div, so the following statement:
meson_mmc_clk |= clk_div;
will have no effect.

As per the datasheet S905 and S922X max divider is 63.
CLK_DIV_MASK[0-5] Cfg_div: Clock divider
Frequency = clock source/cfg_div Clock off: cfg_div==0, the
clock is disabled

                                        Divider bypass: cfg_div==1,

clock source is used as core clock without divider
Maximum divider 63

So here is the log of clk_div and clk_freq at my end.

MMC Device 0 not found
no mmc device at slot 0
clock is disabled (0Hz)
clock is enabled (380953Hz)
......clk_div : 63
Card did not respond to voltage select!
clock is disabled (0Hz)
clock is enabled (380953Hz)
......clk_div : 63
clock is enabled (25000000Hz)

Quoted 8 lines

......clk_div : 40
......clk_div : 40
clock is enabled (52000000Hz)
......clk_div : 20
switch to partitions #0, OK
mmc2(part 0) is current device
Scanning mmc 2:1...
Found U-Boot script /boot/boot.scr

OK, seems you didn't see the issue.

With the original code, let's say mmc->clock = 25000000

clk = SD_EMMC_CLKSRC_DIV2
clk_src = CLK_SRC_DIV2
clk_div = 40

meson_mmc_clk |= CLK_CO_PHASE_180;
meson_mmc_clk |= CLK_TX_PHASE_000;
meson_mmc_clk |= CLK_SRC_DIV2;
meson_mmc_clk |= 40;

=> meson_mmc_clk = (2 << 8) | (0 << 10) | (1 << 6) | 40 => meson_mmc_clk = 0x268

With your code :

meson_mmc_clk |= CLK_DIV_MASK;
meson_mmc_clk |= FIELD_PREP(CLK_SRC_MASK, CRYSTAL_24MHZ);
meson_mmc_clk |= FIELD_PREP(CLK_CORE_PHASE_MASK, CLK_PHASE_180);
meson_mmc_clk |= FIELD_PREP(CLK_TX_PHASE_MASK, CLK_PHASE_0);
meson_mmc_clk |= FIELD_PREP(CLK_RX_PHASE_MASK, CLK_PHASE_0);
meson_mmc_clk |= CLK_SRC_DIV2;
meson_mmc_clk |= 40;
Quoted 7 lines

=> meson_mmc_clk = 0x3f | (0 << 6) | (2 << 8) | (0 << 11) | (0 << 13) | (1 << 6) | 40

-------------------/\---this---------makes-------this-----useless------------------/\

=> 0x27f

It sets the clock to 15873015Hz instead of the 25000000Hz requested.

I did not observer this at my end, but any way thanks for the input.

Quoted 40 lines

so this code sets max divider whatever mmc->clock value, but keeps the CRYSTAL_24MHZ/CLK_SRC_DIV2 selection.

Quoted 34 lines
Quoted 12 lines

drivers/mmc/meson_gx_mmc.c static void meson_mmc_config_clock(struct mmc *mmc) · line 61

Quoted 5 lines
drivers/mmc/meson_gx_mmc.c +2 -0
+     /* Clock source : Crystal 24MHz */
+     meson_mmc_clk |= FIELD_PREP(CLK_SRC_MASK, CRYSTAL_24MHZ);

You set CRYSTAL_24MHZ here, but the src is selected in clk_src and set with:
meson_mmc_clk |= clk_src;

In conclusion your change forces the 24MHz crystal and max divider whatever the freq asked by the mmc core !

As per the datasheet S905 and S922X
Cfg_src: Clock source
0: Crystal 24MHz or other frequencies
selected by clock reset test control register.
1: Fix PLL, 1000MHz Recommended value: 1

Note: *setting cfg_src value to I i.e; Fix PLL 1000 Mhz *
some how break the clk_freq tuning setting in my testing, see the logs below.

MMC Device 0 not found
no mmc device at slot 0
clock is disabled (0Hz)
clock is enabled (380953Hz)
......clk_div : 63
Card did not respond to voltage select!
clock is disabled (0Hz)
clock is enabled (380953Hz)
......clk_div : 63
starting USB...

Quoted 2 lines

No emmc will get discovered,
*This is the real issue I faced for failure of eMMC not getting detected.*

Quoted 6 lines

This is the issue I get on SM1, but when I cap the max freq to 24MHz, it disappears.

This issue is somewhere else, but I don't know where because the Linux driver behaves correctly with the same setup.

My fix was to always use the 24MHz crystal input on non-GX until we find out why, and it still acceptable.

I have studied amlogic u-boot and it seen to use 24MHz crystal inputs. I have following fix the issue with select Fix PLL and CRYSTAL24MHz

       if (mmc->clock > 400000) {
               /* Clock source : Fix PLL, 1000MHz */
               meson_mmc_clk |= FIELD_PREP(CLK_SRC_MASK, FIXPLL_10000MHZ);
       } else {
               /* Clock source : Crystal 24MHz */
               meson_mmc_clk |= FIELD_PREP(CLK_SRC_MASK, CRYSTAL_24MHZ);
       }
Quoted 3 lines

Could you post instead :
- your patch 2 introducing the MMC_COMPATIBLE_* as patch 1

Ok I will change the order.

Quoted 1 line

- this patch but only forcing 24MHz for MMC_COMPATIBLE_AXG as patch 2

I propose the dynamically select 24MHz and Fix PLL, as above code.

Quoted 2 lines

- redude patches 3,4 & 5 to only add mmc* aliases into meson-gx-u-boot.dtsi/meson-g12-common-u-boot.dtsi

Ok I will make these changes

Quoted 1 line

If you have a issue, please chat with me on #linux-amlogic on freenode.

I could not connect to freenode or register my self to this chat group. sorry about that.

Quoted 4 lines

Thanks,
Neil

-Anand

#6 lore raw

PATCH v6 1/5 mmc: meson-gx: Fix clk phase tuning for MMC

Quoted 243 lines · Anand Moon

hi Niel / Jerome,

Thanks for your review comments and debug output
Sorry for late reply.

Quoted 178 lines · Neil Armstrong
Quoted 141 lines · Anand Moon

Hi Neil,

Thanks for you review comments.

Quoted 103 lines · Neil Armstrong

Hi,

Le 09/02/2020 ? 12:05, Anand Moon a ?crit :

Quoted 99 lines

As per mainline line kernel fix the clk tuning phase for mmc, set Core=180, Tx=0, Rx=0 clk phase for mmc initialization. As per S905, S905X, AGX and S922X datasheet set the default values for clk tuning.

---
Changes from previous
v5 Fix the commit message, configure as per mainline kernel.
drop the RX_DELAY_MASK and TX_DELAY_MASK as they are not used.

v4 Fix the update mask value using FIELD_PREP macro.

v3 Fix the initialization of core clk tunning phase as per datasheet.
Fix the commit message.

v2: Fix the clk phase macro to support PHASE_180
drop the wrong CLK_CORE_PHASE_MASK macro.

v1: use the mainline kernel tuning for clk tuning.

Fixed the commmit messages.
Patch v1:
https://patchwork.ozlabs.org/patch/1201208/

Before these changes.

    clock is enabled (380953Hz)
    clock is enabled (25000000Hz)
After these changes
    clock is enabled (380953Hz)
    clock is enabled (25000000Hz)
    clock is enabled (52000000Hz)
Test on Odroid N2 and Odroid C2 with eMMC and microSD cards
---
 arch/arm/include/asm/arch-meson/sd_emmc.h | 24 +++++++++++--------
 drivers/mmc/meson_gx_mmc.c                | 28 +++++++++++++++++++----
 2 files changed, 38 insertions(+), 14 deletions(-)
arch/arm/include/asm/arch-meson/sd_emmc.h +15 -9
index e3a72c8b66..f4299485dc 100644
@@ -7,6 +7,7 @@
 #define __SD_EMMC_H__
 
 #include <mmc.h>
+#include <linux/bitops.h>
 
 #define SDIO_PORT_A                  0
 #define SDIO_PORT_B                  1
@@ -19,15 +20,20 @@
 #define   CLK_MAX_DIV                        63
 #define   CLK_SRC_24M                        (0 << 6)
 #define   CLK_SRC_DIV2                       (1 << 6)
-#define   CLK_CO_PHASE_000           (0 << 8)
-#define   CLK_CO_PHASE_090           (1 << 8)
-#define   CLK_CO_PHASE_180           (2 << 8)
-#define   CLK_CO_PHASE_270           (3 << 8)
-#define   CLK_TX_PHASE_000           (0 << 10)
-#define   CLK_TX_PHASE_090           (1 << 10)
-#define   CLK_TX_PHASE_180           (2 << 10)
-#define   CLK_TX_PHASE_270           (3 << 10)
-#define   CLK_ALWAYS_ON                      BIT(24)
+
+#define   CRYSTAL_24MHZ                      0
+#define   CLK_PHASE_0                        0
+#define   CLK_PHASE_180                      2
+
+#define   CLK_DIV_MASK                       GENMASK(5, 0)
+#define   CLK_SRC_MASK                       GENMASK(7, 6)
+#define   CLK_CORE_PHASE_MASK                GENMASK(9, 8)
+#define   CLK_TX_PHASE_MASK          GENMASK(11, 10)
+#define   CLK_RX_PHASE_MASK          GENMASK(13, 12)
+
+#define   CLK_V2_ALWAYS_ON           BIT(24)
+
+#define   CLK_V3_ALWAYS_ON           BIT(28)
 
 #define MESON_SD_EMMC_CFG            0x44
 #define   CFG_BUS_WIDTH_MASK         GENMASK(1, 0)
drivers/mmc/meson_gx_mmc.c +4 -0
index 86c1a7164a..b013c7c5fb 100644
@@ -16,6 +16,10 @@
 #include <asm/arch/sd_emmc.h>
 #include <linux/log2.h>
 
+#include <linux/bitops.h>
+#include <linux/compat.h>
+#include <linux/bitfield.h>
+
 static inline void *get_regbase(const struct mmc *mmc)
 {
      struct meson_mmc_platdata *pdata = mmc->priv;
@@ -51,11 +55,25 @@ static void meson_mmc_config_clock(struct mmc *mmc)
      }
      clk_div = DIV_ROUND_UP(clk, mmc->clock);
 
Quoted 11 lines

drivers/mmc/meson_gx_mmc.c static void meson_mmc_config_clock(struct mmc *mmc) · line 59

Quoted 7 lines
drivers/mmc/meson_gx_mmc.c +2 -5
-     /* 180 phase core clock */
-     meson_mmc_clk |= CLK_CO_PHASE_180;
-
-     /* 180 phase tx clock */
-     meson_mmc_clk |= CLK_TX_PHASE_000;
+     /* Clock divider */
+     meson_mmc_clk |= CLK_DIV_MASK;

This will set the max divider, whatever the value of clk_div, so the following statement:
meson_mmc_clk |= clk_div;
will have no effect.

As per the datasheet S905 and S922X max divider is 63.
CLK_DIV_MASK[0-5] Cfg_div: Clock divider
Frequency = clock source/cfg_div Clock off: cfg_div==0, the
clock is disabled

                                        Divider bypass: cfg_div==1,

clock source is used as core clock without divider
Maximum divider 63

So here is the log of clk_div and clk_freq at my end.

MMC Device 0 not found
no mmc device at slot 0
clock is disabled (0Hz)
clock is enabled (380953Hz)
......clk_div : 63
Card did not respond to voltage select!
clock is disabled (0Hz)
clock is enabled (380953Hz)
......clk_div : 63
clock is enabled (25000000Hz)

Quoted 8 lines

......clk_div : 40
......clk_div : 40
clock is enabled (52000000Hz)
......clk_div : 20
switch to partitions #0, OK
mmc2(part 0) is current device
Scanning mmc 2:1...
Found U-Boot script /boot/boot.scr

OK, seems you didn't see the issue.

With the original code, let's say mmc->clock = 25000000

clk = SD_EMMC_CLKSRC_DIV2
clk_src = CLK_SRC_DIV2
clk_div = 40

meson_mmc_clk |= CLK_CO_PHASE_180;
meson_mmc_clk |= CLK_TX_PHASE_000;
meson_mmc_clk |= CLK_SRC_DIV2;
meson_mmc_clk |= 40;

=> meson_mmc_clk = (2 << 8) | (0 << 10) | (1 << 6) | 40 => meson_mmc_clk = 0x268

With your code :

meson_mmc_clk |= CLK_DIV_MASK;
meson_mmc_clk |= FIELD_PREP(CLK_SRC_MASK, CRYSTAL_24MHZ);
meson_mmc_clk |= FIELD_PREP(CLK_CORE_PHASE_MASK, CLK_PHASE_180);
meson_mmc_clk |= FIELD_PREP(CLK_TX_PHASE_MASK, CLK_PHASE_0);
meson_mmc_clk |= FIELD_PREP(CLK_RX_PHASE_MASK, CLK_PHASE_0);
meson_mmc_clk |= CLK_SRC_DIV2;
meson_mmc_clk |= 40;
Quoted 7 lines

=> meson_mmc_clk = 0x3f | (0 << 6) | (2 << 8) | (0 << 11) | (0 << 13) | (1 << 6) | 40

-------------------/\---this---------makes-------this-----useless------------------/\

=> 0x27f

It sets the clock to 15873015Hz instead of the 25000000Hz requested.

I did not observer this at my end, but any way thanks for the input.

Quoted 40 lines

so this code sets max divider whatever mmc->clock value, but keeps the CRYSTAL_24MHZ/CLK_SRC_DIV2 selection.

Quoted 34 lines
Quoted 12 lines

drivers/mmc/meson_gx_mmc.c static void meson_mmc_config_clock(struct mmc *mmc) · line 61

Quoted 5 lines
drivers/mmc/meson_gx_mmc.c +2 -0
+     /* Clock source : Crystal 24MHz */
+     meson_mmc_clk |= FIELD_PREP(CLK_SRC_MASK, CRYSTAL_24MHZ);

You set CRYSTAL_24MHZ here, but the src is selected in clk_src and set with:
meson_mmc_clk |= clk_src;

In conclusion your change forces the 24MHz crystal and max divider whatever the freq asked by the mmc core !

As per the datasheet S905 and S922X
Cfg_src: Clock source
0: Crystal 24MHz or other frequencies
selected by clock reset test control register.
1: Fix PLL, 1000MHz Recommended value: 1

Note: *setting cfg_src value to I i.e; Fix PLL 1000 Mhz *
some how break the clk_freq tuning setting in my testing, see the logs below.

MMC Device 0 not found
no mmc device at slot 0
clock is disabled (0Hz)
clock is enabled (380953Hz)
......clk_div : 63
Card did not respond to voltage select!
clock is disabled (0Hz)
clock is enabled (380953Hz)
......clk_div : 63
starting USB...

Quoted 2 lines

No emmc will get discovered,
*This is the real issue I faced for failure of eMMC not getting detected.*

Quoted 6 lines

This is the issue I get on SM1, but when I cap the max freq to 24MHz, it disappears.

This issue is somewhere else, but I don't know where because the Linux driver behaves correctly with the same setup.

My fix was to always use the 24MHz crystal input on non-GX until we find out why, and it still acceptable.

I have studied amlogic u-boot and it seen to use 24MHz crystal inputs. I have following fix the issue with select Fix PLL and CRYSTAL24MHz

Quoted 7 lines
       if (mmc->clock > 400000) {
               /* Clock source : Fix PLL, 1000MHz */
               meson_mmc_clk |= FIELD_PREP(CLK_SRC_MASK, FIXPLL_10000MHZ);
       } else {
               /* Clock source : Crystal 24MHz */
               meson_mmc_clk |= FIELD_PREP(CLK_SRC_MASK, CRYSTAL_24MHZ);
       }

This is still wrong and broken. The original code is correct and works fine.

As Jerome said, the underlying issue must be understood, why when using the FIXPLL clock source, it fails ?

The clock setup function is correct, don't try to fix it.

The weirdness is why does it works under linux ? maybe the fixpll clock setup is different ?

Could you dump the emmc and clock registers from linux to see the difference ?

Neil

Quoted 27 lines
Quoted 3 lines

Could you post instead :
- your patch 2 introducing the MMC_COMPATIBLE_* as patch 1

Ok I will change the order.

Quoted 1 line

- this patch but only forcing 24MHz for MMC_COMPATIBLE_AXG as patch 2

I propose the dynamically select 24MHz and Fix PLL, as above code.

Quoted 2 lines

- redude patches 3,4 & 5 to only add mmc* aliases into meson-gx-u-boot.dtsi/meson-g12-common-u-boot.dtsi

Ok I will make these changes

Quoted 1 line

If you have a issue, please chat with me on #linux-amlogic on freenode.

I could not connect to freenode or register my self to this chat group. sorry about that.

Quoted 4 lines

Thanks,
Neil

-Anand

author
#7 lore raw

PATCH v6 1/5 mmc: meson-gx: Fix clk phase tuning for MMC

Hi Neil,

Quoted 257 lines · Neil Armstrong
Quoted 243 lines · Anand Moon

hi Niel / Jerome,

Thanks for your review comments and debug output
Sorry for late reply.

Quoted 178 lines · Neil Armstrong
Quoted 141 lines · Anand Moon

Hi Neil,

Thanks for you review comments.

Quoted 103 lines · Neil Armstrong

Hi,

Le 09/02/2020 ? 12:05, Anand Moon a ?crit :

Quoted 99 lines

As per mainline line kernel fix the clk tuning phase for mmc, set Core=180, Tx=0, Rx=0 clk phase for mmc initialization. As per S905, S905X, AGX and S922X datasheet set the default values for clk tuning.

---
Changes from previous
v5 Fix the commit message, configure as per mainline kernel.
drop the RX_DELAY_MASK and TX_DELAY_MASK as they are not used.

v4 Fix the update mask value using FIELD_PREP macro.

v3 Fix the initialization of core clk tunning phase as per datasheet.
Fix the commit message.

v2: Fix the clk phase macro to support PHASE_180
drop the wrong CLK_CORE_PHASE_MASK macro.

v1: use the mainline kernel tuning for clk tuning.

Fixed the commmit messages.
Patch v1:
https://patchwork.ozlabs.org/patch/1201208/

Before these changes.

    clock is enabled (380953Hz)
    clock is enabled (25000000Hz)
After these changes
    clock is enabled (380953Hz)
    clock is enabled (25000000Hz)
    clock is enabled (52000000Hz)
Test on Odroid N2 and Odroid C2 with eMMC and microSD cards
---
 arch/arm/include/asm/arch-meson/sd_emmc.h | 24 +++++++++++--------
 drivers/mmc/meson_gx_mmc.c                | 28 +++++++++++++++++++----
 2 files changed, 38 insertions(+), 14 deletions(-)
arch/arm/include/asm/arch-meson/sd_emmc.h +15 -9
index e3a72c8b66..f4299485dc 100644
@@ -7,6 +7,7 @@
 #define __SD_EMMC_H__
 
 #include <mmc.h>
+#include <linux/bitops.h>
 
 #define SDIO_PORT_A                  0
 #define SDIO_PORT_B                  1
@@ -19,15 +20,20 @@
 #define   CLK_MAX_DIV                        63
 #define   CLK_SRC_24M                        (0 << 6)
 #define   CLK_SRC_DIV2                       (1 << 6)
-#define   CLK_CO_PHASE_000           (0 << 8)
-#define   CLK_CO_PHASE_090           (1 << 8)
-#define   CLK_CO_PHASE_180           (2 << 8)
-#define   CLK_CO_PHASE_270           (3 << 8)
-#define   CLK_TX_PHASE_000           (0 << 10)
-#define   CLK_TX_PHASE_090           (1 << 10)
-#define   CLK_TX_PHASE_180           (2 << 10)
-#define   CLK_TX_PHASE_270           (3 << 10)
-#define   CLK_ALWAYS_ON                      BIT(24)
+
+#define   CRYSTAL_24MHZ                      0
+#define   CLK_PHASE_0                        0
+#define   CLK_PHASE_180                      2
+
+#define   CLK_DIV_MASK                       GENMASK(5, 0)
+#define   CLK_SRC_MASK                       GENMASK(7, 6)
+#define   CLK_CORE_PHASE_MASK                GENMASK(9, 8)
+#define   CLK_TX_PHASE_MASK          GENMASK(11, 10)
+#define   CLK_RX_PHASE_MASK          GENMASK(13, 12)
+
+#define   CLK_V2_ALWAYS_ON           BIT(24)
+
+#define   CLK_V3_ALWAYS_ON           BIT(28)
 
 #define MESON_SD_EMMC_CFG            0x44
 #define   CFG_BUS_WIDTH_MASK         GENMASK(1, 0)
drivers/mmc/meson_gx_mmc.c +4 -0
index 86c1a7164a..b013c7c5fb 100644
@@ -16,6 +16,10 @@
 #include <asm/arch/sd_emmc.h>
 #include <linux/log2.h>
 
+#include <linux/bitops.h>
+#include <linux/compat.h>
+#include <linux/bitfield.h>
+
 static inline void *get_regbase(const struct mmc *mmc)
 {
      struct meson_mmc_platdata *pdata = mmc->priv;
@@ -51,11 +55,25 @@ static void meson_mmc_config_clock(struct mmc *mmc)
      }
      clk_div = DIV_ROUND_UP(clk, mmc->clock);
 
Quoted 11 lines

drivers/mmc/meson_gx_mmc.c static void meson_mmc_config_clock(struct mmc *mmc) · line 59

Quoted 7 lines
drivers/mmc/meson_gx_mmc.c +2 -5
-     /* 180 phase core clock */
-     meson_mmc_clk |= CLK_CO_PHASE_180;
-
-     /* 180 phase tx clock */
-     meson_mmc_clk |= CLK_TX_PHASE_000;
+     /* Clock divider */
+     meson_mmc_clk |= CLK_DIV_MASK;

This will set the max divider, whatever the value of clk_div, so the following statement:
meson_mmc_clk |= clk_div;
will have no effect.

As per the datasheet S905 and S922X max divider is 63.
CLK_DIV_MASK[0-5] Cfg_div: Clock divider
Frequency = clock source/cfg_div Clock off: cfg_div==0, the
clock is disabled

                                        Divider bypass: cfg_div==1,

clock source is used as core clock without divider
Maximum divider 63

So here is the log of clk_div and clk_freq at my end.

MMC Device 0 not found
no mmc device at slot 0
clock is disabled (0Hz)
clock is enabled (380953Hz)
......clk_div : 63
Card did not respond to voltage select!
clock is disabled (0Hz)
clock is enabled (380953Hz)
......clk_div : 63
clock is enabled (25000000Hz)

Quoted 8 lines

......clk_div : 40
......clk_div : 40
clock is enabled (52000000Hz)
......clk_div : 20
switch to partitions #0, OK
mmc2(part 0) is current device
Scanning mmc 2:1...
Found U-Boot script /boot/boot.scr

OK, seems you didn't see the issue.

With the original code, let's say mmc->clock = 25000000

clk = SD_EMMC_CLKSRC_DIV2
clk_src = CLK_SRC_DIV2
clk_div = 40

meson_mmc_clk |= CLK_CO_PHASE_180;
meson_mmc_clk |= CLK_TX_PHASE_000;
meson_mmc_clk |= CLK_SRC_DIV2;
meson_mmc_clk |= 40;

=> meson_mmc_clk = (2 << 8) | (0 << 10) | (1 << 6) | 40 => meson_mmc_clk = 0x268

With your code :

meson_mmc_clk |= CLK_DIV_MASK;
meson_mmc_clk |= FIELD_PREP(CLK_SRC_MASK, CRYSTAL_24MHZ);
meson_mmc_clk |= FIELD_PREP(CLK_CORE_PHASE_MASK, CLK_PHASE_180);
meson_mmc_clk |= FIELD_PREP(CLK_TX_PHASE_MASK, CLK_PHASE_0);
meson_mmc_clk |= FIELD_PREP(CLK_RX_PHASE_MASK, CLK_PHASE_0);
meson_mmc_clk |= CLK_SRC_DIV2;
meson_mmc_clk |= 40;
Quoted 7 lines

=> meson_mmc_clk = 0x3f | (0 << 6) | (2 << 8) | (0 << 11) | (0 << 13) | (1 << 6) | 40

-------------------/\---this---------makes-------this-----useless------------------/\

=> 0x27f

It sets the clock to 15873015Hz instead of the 25000000Hz requested.

I did not observer this at my end, but any way thanks for the input.

Quoted 40 lines

so this code sets max divider whatever mmc->clock value, but keeps the CRYSTAL_24MHZ/CLK_SRC_DIV2 selection.

Quoted 34 lines
Quoted 12 lines

drivers/mmc/meson_gx_mmc.c static void meson_mmc_config_clock(struct mmc *mmc) · line 61

Quoted 5 lines
drivers/mmc/meson_gx_mmc.c +2 -0
+     /* Clock source : Crystal 24MHz */
+     meson_mmc_clk |= FIELD_PREP(CLK_SRC_MASK, CRYSTAL_24MHZ);

You set CRYSTAL_24MHZ here, but the src is selected in clk_src and set with:
meson_mmc_clk |= clk_src;

In conclusion your change forces the 24MHz crystal and max divider whatever the freq asked by the mmc core !

As per the datasheet S905 and S922X
Cfg_src: Clock source
0: Crystal 24MHz or other frequencies
selected by clock reset test control register.
1: Fix PLL, 1000MHz Recommended value: 1

Note: *setting cfg_src value to I i.e; Fix PLL 1000 Mhz *
some how break the clk_freq tuning setting in my testing, see the logs below.

MMC Device 0 not found
no mmc device at slot 0
clock is disabled (0Hz)
clock is enabled (380953Hz)
......clk_div : 63
Card did not respond to voltage select!
clock is disabled (0Hz)
clock is enabled (380953Hz)
......clk_div : 63
starting USB...

Quoted 2 lines

No emmc will get discovered,
*This is the real issue I faced for failure of eMMC not getting detected.*

Quoted 6 lines

This is the issue I get on SM1, but when I cap the max freq to 24MHz, it disappears.

This issue is somewhere else, but I don't know where because the Linux driver behaves correctly with the same setup.

My fix was to always use the 24MHz crystal input on non-GX until we find out why, and it still acceptable.

I have studied amlogic u-boot and it seen to use 24MHz crystal inputs. I have following fix the issue with select Fix PLL and CRYSTAL24MHz

Quoted 7 lines
       if (mmc->clock > 400000) {
               /* Clock source : Fix PLL, 1000MHz */
               meson_mmc_clk |= FIELD_PREP(CLK_SRC_MASK, FIXPLL_10000MHZ);
       } else {
               /* Clock source : Crystal 24MHz */
               meson_mmc_clk |= FIELD_PREP(CLK_SRC_MASK, CRYSTAL_24MHZ);
       }

This is still wrong and broken. The original code is correct and works fine.

As Jerome said, the underlying issue must be understood, why when using the FIXPLL clock source, it fails ?

Quoted 8 lines

The clock setup function is correct, don't try to fix it.

The weirdness is why does it works under linux ? maybe the fixpll clock setup is different ?

Could you dump the emmc and clock registers from linux to see the difference ?

Neil

Ok thanks for this Input. I will try to figure our how it's working in linux kernel first.

-Anand

Quoted 28 lines
Quoted 27 lines
Quoted 3 lines

Could you post instead :
- your patch 2 introducing the MMC_COMPATIBLE_* as patch 1

Ok I will change the order.

Quoted 1 line

- this patch but only forcing 24MHz for MMC_COMPATIBLE_AXG as patch 2

I propose the dynamically select 24MHz and Fix PLL, as above code.

Quoted 2 lines

- redude patches 3,4 & 5 to only add mmc* aliases into meson-gx-u-boot.dtsi/meson-g12-common-u-boot.dtsi

Ok I will make these changes

Quoted 1 line

If you have a issue, please chat with me on #linux-amlogic on freenode.

I could not connect to freenode or register my self to this chat group. sorry about that.

Quoted 4 lines

Thanks,
Neil

-Anand

reviewer
#8 lore raw

PATCH v6 1/5 mmc: meson-gx: Fix clk phase tuning for MMC

In reply to Anand Moon
Quoted 183 lines · Anand Moon

Hi Neil,

Thanks for you review comments.

Quoted 103 lines · Neil Armstrong

Hi,

Quoted 99 lines · Anand Moon

As per mainline line kernel fix the clk tuning phase for mmc, set Core=180, Tx=0, Rx=0 clk phase for mmc initialization. As per S905, S905X, AGX and S922X datasheet set the default values for clk tuning.

---
Changes from previous
v5 Fix the commit message, configure as per mainline kernel.
drop the RX_DELAY_MASK and TX_DELAY_MASK as they are not used.

v4 Fix the update mask value using FIELD_PREP macro.

v3 Fix the initialization of core clk tunning phase as per datasheet.
Fix the commit message.

v2: Fix the clk phase macro to support PHASE_180
drop the wrong CLK_CORE_PHASE_MASK macro.

v1: use the mainline kernel tuning for clk tuning.

Fixed the commmit messages.
Patch v1:
https://patchwork.ozlabs.org/patch/1201208/

Before these changes.

    clock is enabled (380953Hz)
    clock is enabled (25000000Hz)
After these changes
    clock is enabled (380953Hz)
    clock is enabled (25000000Hz)
    clock is enabled (52000000Hz)
Test on Odroid N2 and Odroid C2 with eMMC and microSD cards
---
 arch/arm/include/asm/arch-meson/sd_emmc.h | 24 +++++++++++--------
 drivers/mmc/meson_gx_mmc.c                | 28 +++++++++++++++++++----
 2 files changed, 38 insertions(+), 14 deletions(-)
arch/arm/include/asm/arch-meson/sd_emmc.h +15 -9
index e3a72c8b66..f4299485dc 100644
@@ -7,6 +7,7 @@
 #define __SD_EMMC_H__
 
 #include <mmc.h>
+#include <linux/bitops.h>
 
 #define SDIO_PORT_A                  0
 #define SDIO_PORT_B                  1
@@ -19,15 +20,20 @@
 #define   CLK_MAX_DIV                        63
 #define   CLK_SRC_24M                        (0 << 6)
 #define   CLK_SRC_DIV2                       (1 << 6)
-#define   CLK_CO_PHASE_000           (0 << 8)
-#define   CLK_CO_PHASE_090           (1 << 8)
-#define   CLK_CO_PHASE_180           (2 << 8)
-#define   CLK_CO_PHASE_270           (3 << 8)
-#define   CLK_TX_PHASE_000           (0 << 10)
-#define   CLK_TX_PHASE_090           (1 << 10)
-#define   CLK_TX_PHASE_180           (2 << 10)
-#define   CLK_TX_PHASE_270           (3 << 10)
-#define   CLK_ALWAYS_ON                      BIT(24)
+
+#define   CRYSTAL_24MHZ                      0
+#define   CLK_PHASE_0                        0
+#define   CLK_PHASE_180                      2
+
+#define   CLK_DIV_MASK                       GENMASK(5, 0)
+#define   CLK_SRC_MASK                       GENMASK(7, 6)
+#define   CLK_CORE_PHASE_MASK                GENMASK(9, 8)
+#define   CLK_TX_PHASE_MASK          GENMASK(11, 10)
+#define   CLK_RX_PHASE_MASK          GENMASK(13, 12)
+
+#define   CLK_V2_ALWAYS_ON           BIT(24)
+
+#define   CLK_V3_ALWAYS_ON           BIT(28)
 
 #define MESON_SD_EMMC_CFG            0x44
 #define   CFG_BUS_WIDTH_MASK         GENMASK(1, 0)
drivers/mmc/meson_gx_mmc.c +4 -0
index 86c1a7164a..b013c7c5fb 100644
@@ -16,6 +16,10 @@
 #include <asm/arch/sd_emmc.h>
 #include <linux/log2.h>
 
+#include <linux/bitops.h>
+#include <linux/compat.h>
+#include <linux/bitfield.h>
+
 static inline void *get_regbase(const struct mmc *mmc)
 {
      struct meson_mmc_platdata *pdata = mmc->priv;
@@ -51,11 +55,25 @@ static void meson_mmc_config_clock(struct mmc *mmc)
      }
      clk_div = DIV_ROUND_UP(clk, mmc->clock);
 
Quoted 11 lines

drivers/mmc/meson_gx_mmc.c static void meson_mmc_config_clock(struct mmc *mmc) · line 59

Quoted 7 lines
drivers/mmc/meson_gx_mmc.c +2 -5
-     /* 180 phase core clock */
-     meson_mmc_clk |= CLK_CO_PHASE_180;
-
-     /* 180 phase tx clock */
-     meson_mmc_clk |= CLK_TX_PHASE_000;
+     /* Clock divider */
+     meson_mmc_clk |= CLK_DIV_MASK;

This will set the max divider, whatever the value of clk_div, so the following statement:
meson_mmc_clk |= clk_div;
will have no effect.

As per the datasheet S905 and S922X max divider is 63.
CLK_DIV_MASK[0-5] Cfg_div: Clock divider
Frequency = clock source/cfg_div Clock off: cfg_div==0, the
clock is disabled

                                        Divider bypass: cfg_div==1,

clock source is used as core clock without divider
Maximum divider 63

So here is the log of clk_div and clk_freq at my end.

MMC Device 0 not found
no mmc device at slot 0
clock is disabled (0Hz)
clock is enabled (380953Hz)
......clk_div : 63
Card did not respond to voltage select!
clock is disabled (0Hz)
clock is enabled (380953Hz)
......clk_div : 63
clock is enabled (25000000Hz)
......clk_div : 40
......clk_div : 40
clock is enabled (52000000Hz)
......clk_div : 20
switch to partitions #0, OK
mmc2(part 0) is current device
Scanning mmc 2:1...
Found U-Boot script /boot/boot.scr

Quoted 11 lines

drivers/mmc/meson_gx_mmc.c static void meson_mmc_config_clock(struct mmc *mmc) · line 61

Quoted 4 lines
drivers/mmc/meson_gx_mmc.c +2 -0
+     /* Clock source : Crystal 24MHz */
+     meson_mmc_clk |= FIELD_PREP(CLK_SRC_MASK, CRYSTAL_24MHZ);

You set CRYSTAL_24MHZ here, but the src is selected in clk_src and set with:
meson_mmc_clk |= clk_src;

In conclusion your change forces the 24MHz crystal and max divider whatever the freq asked by the mmc core !

As per the datasheet S905 and S922X
Cfg_src: Clock source
0: Crystal 24MHz or other frequencies
selected by clock reset test control register.
1: Fix PLL, 1000MHz Recommended value: 1

Note: *setting cfg_src value to I i.e; Fix PLL 1000 Mhz *
some how break the clk_freq tuning setting in my testing, see the logs below.

MMC Device 0 not found
no mmc device at slot 0
clock is disabled (0Hz)
clock is enabled (380953Hz)
......clk_div : 63
Card did not respond to voltage select!
clock is disabled (0Hz)
clock is enabled (380953Hz)
......clk_div : 63
starting USB...

Quoted 3 lines

No emmc will get discovered,
*This is the real issue I faced for failure of eMMC not getting detected.*

I don't think the reality of the issue reported has been questioned. What is being questioned is the proposed solution.

The patch you sent forces clock input 0 with the maximum divider possible. This is an important comment for which an explanation is missing AFAICT.

1) The doc is not clear but input 0 is not always the oscillator. It is the MMC composite clock which can set to several different sources, especially when the ROM code boots from another device, such as SPI This is the topic of 2 patches I sent recently (not yet merged)

2) Let's assume that input 0 is indeed 24M, your patches forces this with a 63 divider => 380kHz. With a clock that low, the phase does not matter much anymore

IOW, you are the only one to report this issue on one specific case, the cause of the issue is not really identified and the work around would:
* Add statements without effect in the code
* Considerably slow down eMMC and SDCard on all amlogic platforms.
* Provide no explanation about how it actually solves something

This is problematic ...

Quoted 33 lines
Quoted 10 lines

drivers/mmc/meson_gx_mmc.c static void meson_mmc_config_clock(struct mmc *mmc) · line 67

Quoted 7 lines
drivers/mmc/meson_gx_mmc.c +6 -0
+     /* Core clock phase 2:180 */
+     meson_mmc_clk |= FIELD_PREP(CLK_CORE_PHASE_MASK, CLK_PHASE_180);
+     /* TX clock phase 0:180 */
+     meson_mmc_clk |= FIELD_PREP(CLK_TX_PHASE_MASK, CLK_PHASE_0);
+     /* RX clock phase 0:180 */
+     meson_mmc_clk |= FIELD_PREP(CLK_RX_PHASE_MASK, CLK_PHASE_0);

These are ok, but it's exactly the same as before with a different style.

Quoted 11 lines

drivers/mmc/meson_gx_mmc.c static void meson_mmc_config_clock(struct mmc *mmc) · line 76

Quoted 9 lines
drivers/mmc/meson_gx_mmc.c +9 -0
+
+#ifdef CONFIG_MESON_GX
+     /* clk always on */
+     meson_mmc_clk |= CLK_V2_ALWAYS_ON;
+#endif
+#if (defined(CONFIG_MESON_AXG) || defined(CONFIG_MESON_G12A))
+     /* clk always on */
+     meson_mmc_clk |= CLK_V3_ALWAYS_ON;
+#endif

Why not, not sure about the effect.

Ok, I will changes these to FIELD_PREP for consultancy.

Quoted 7 lines

drivers/mmc/meson_gx_mmc.c static void meson_mmc_config_clock(struct mmc *mmc)

Quoted 5 lines
drivers/mmc/meson_gx_mmc.c +0 -0
      /* clock settings */
      meson_mmc_clk |= clk_src;
 

Neil

-Anand

author
#9 lore raw

PATCH v6 1/5 mmc: meson-gx: Fix clk phase tuning for MMC

Hi Jerome / Neil,

Quoted 207 lines · Jerome Brunet
Quoted 183 lines · Anand Moon

Hi Neil,

Thanks for you review comments.

Quoted 103 lines · Neil Armstrong

Hi,

Le 09/02/2020 ? 12:05, Anand Moon a ?crit :

Quoted 99 lines

As per mainline line kernel fix the clk tuning phase for mmc, set Core=180, Tx=0, Rx=0 clk phase for mmc initialization. As per S905, S905X, AGX and S922X datasheet set the default values for clk tuning.

---
Changes from previous
v5 Fix the commit message, configure as per mainline kernel.
drop the RX_DELAY_MASK and TX_DELAY_MASK as they are not used.

v4 Fix the update mask value using FIELD_PREP macro.

v3 Fix the initialization of core clk tunning phase as per datasheet.
Fix the commit message.

v2: Fix the clk phase macro to support PHASE_180
drop the wrong CLK_CORE_PHASE_MASK macro.

v1: use the mainline kernel tuning for clk tuning.

Fixed the commmit messages.
Patch v1:
https://patchwork.ozlabs.org/patch/1201208/

Before these changes.

    clock is enabled (380953Hz)
    clock is enabled (25000000Hz)
After these changes
    clock is enabled (380953Hz)
    clock is enabled (25000000Hz)
    clock is enabled (52000000Hz)
Test on Odroid N2 and Odroid C2 with eMMC and microSD cards
---
 arch/arm/include/asm/arch-meson/sd_emmc.h | 24 +++++++++++--------
 drivers/mmc/meson_gx_mmc.c                | 28 +++++++++++++++++++----
 2 files changed, 38 insertions(+), 14 deletions(-)
arch/arm/include/asm/arch-meson/sd_emmc.h +15 -9
index e3a72c8b66..f4299485dc 100644
@@ -7,6 +7,7 @@
 #define __SD_EMMC_H__
 
 #include <mmc.h>
+#include <linux/bitops.h>
 
 #define SDIO_PORT_A                  0
 #define SDIO_PORT_B                  1
@@ -19,15 +20,20 @@
 #define   CLK_MAX_DIV                        63
 #define   CLK_SRC_24M                        (0 << 6)
 #define   CLK_SRC_DIV2                       (1 << 6)
-#define   CLK_CO_PHASE_000           (0 << 8)
-#define   CLK_CO_PHASE_090           (1 << 8)
-#define   CLK_CO_PHASE_180           (2 << 8)
-#define   CLK_CO_PHASE_270           (3 << 8)
-#define   CLK_TX_PHASE_000           (0 << 10)
-#define   CLK_TX_PHASE_090           (1 << 10)
-#define   CLK_TX_PHASE_180           (2 << 10)
-#define   CLK_TX_PHASE_270           (3 << 10)
-#define   CLK_ALWAYS_ON                      BIT(24)
+
+#define   CRYSTAL_24MHZ                      0
+#define   CLK_PHASE_0                        0
+#define   CLK_PHASE_180                      2
+
+#define   CLK_DIV_MASK                       GENMASK(5, 0)
+#define   CLK_SRC_MASK                       GENMASK(7, 6)
+#define   CLK_CORE_PHASE_MASK                GENMASK(9, 8)
+#define   CLK_TX_PHASE_MASK          GENMASK(11, 10)
+#define   CLK_RX_PHASE_MASK          GENMASK(13, 12)
+
+#define   CLK_V2_ALWAYS_ON           BIT(24)
+
+#define   CLK_V3_ALWAYS_ON           BIT(28)
 
 #define MESON_SD_EMMC_CFG            0x44
 #define   CFG_BUS_WIDTH_MASK         GENMASK(1, 0)
drivers/mmc/meson_gx_mmc.c +4 -0
index 86c1a7164a..b013c7c5fb 100644
@@ -16,6 +16,10 @@
 #include <asm/arch/sd_emmc.h>
 #include <linux/log2.h>
 
+#include <linux/bitops.h>
+#include <linux/compat.h>
+#include <linux/bitfield.h>
+
 static inline void *get_regbase(const struct mmc *mmc)
 {
      struct meson_mmc_platdata *pdata = mmc->priv;
@@ -51,11 +55,25 @@ static void meson_mmc_config_clock(struct mmc *mmc)
      }
      clk_div = DIV_ROUND_UP(clk, mmc->clock);
 
Quoted 11 lines

drivers/mmc/meson_gx_mmc.c static void meson_mmc_config_clock(struct mmc *mmc) · line 59

Quoted 7 lines
drivers/mmc/meson_gx_mmc.c +2 -5
-     /* 180 phase core clock */
-     meson_mmc_clk |= CLK_CO_PHASE_180;
-
-     /* 180 phase tx clock */
-     meson_mmc_clk |= CLK_TX_PHASE_000;
+     /* Clock divider */
+     meson_mmc_clk |= CLK_DIV_MASK;

This will set the max divider, whatever the value of clk_div, so the following statement:
meson_mmc_clk |= clk_div;
will have no effect.

As per the datasheet S905 and S922X max divider is 63.
CLK_DIV_MASK[0-5] Cfg_div: Clock divider
Frequency = clock source/cfg_div Clock off: cfg_div==0, the
clock is disabled

                                        Divider bypass: cfg_div==1,

clock source is used as core clock without divider
Maximum divider 63

So here is the log of clk_div and clk_freq at my end.

MMC Device 0 not found
no mmc device at slot 0
clock is disabled (0Hz)
clock is enabled (380953Hz)
......clk_div : 63
Card did not respond to voltage select!
clock is disabled (0Hz)
clock is enabled (380953Hz)
......clk_div : 63
clock is enabled (25000000Hz)
......clk_div : 40
......clk_div : 40
clock is enabled (52000000Hz)
......clk_div : 20
switch to partitions #0, OK
mmc2(part 0) is current device
Scanning mmc 2:1...
Found U-Boot script /boot/boot.scr

Quoted 11 lines

drivers/mmc/meson_gx_mmc.c static void meson_mmc_config_clock(struct mmc *mmc) · line 61

Quoted 4 lines
drivers/mmc/meson_gx_mmc.c +2 -0
+     /* Clock source : Crystal 24MHz */
+     meson_mmc_clk |= FIELD_PREP(CLK_SRC_MASK, CRYSTAL_24MHZ);

You set CRYSTAL_24MHZ here, but the src is selected in clk_src and set with:
meson_mmc_clk |= clk_src;

In conclusion your change forces the 24MHz crystal and max divider whatever the freq asked by the mmc core !

As per the datasheet S905 and S922X
Cfg_src: Clock source
0: Crystal 24MHz or other frequencies
selected by clock reset test control register.
1: Fix PLL, 1000MHz Recommended value: 1

Note: *setting cfg_src value to I i.e; Fix PLL 1000 Mhz *
some how break the clk_freq tuning setting in my testing, see the logs below.

MMC Device 0 not found
no mmc device at slot 0
clock is disabled (0Hz)
clock is enabled (380953Hz)
......clk_div : 63
Card did not respond to voltage select!
clock is disabled (0Hz)
clock is enabled (380953Hz)
......clk_div : 63
starting USB...

Quoted 3 lines

No emmc will get discovered,
*This is the real issue I faced for failure of eMMC not getting detected.*

I don't think the reality of the issue reported has been questioned. What is being questioned is the proposed solution.

The patch you sent forces clock input 0 with the maximum divider possible. This is an important comment for which an explanation is missing AFAICT.

1) The doc is not clear but input 0 is not always the oscillator. It is the MMC composite clock which can set to several different sources, especially when the ROM code boots from another device, such as SPI This is the topic of 2 patches I sent recently (not yet merged)

2) Let's assume that input 0 is indeed 24M, your patches forces this with a 63 divider => 380kHz. With a clock that low, the phase does not matter much anymore

Quoted 8 lines

IOW, you are the only one to report this issue on one specific case, the cause of the issue is not really identified and the work around would:
* Add statements without effect in the code
* Considerably slow down eMMC and SDCard on all amlogic platforms.
* Provide no explanation about how it actually solves something

This is problematic ...

Ok Thanks for your review comments.
I have tried to test these on all the device that I have with all the emmc sdcards.
I have almost used the mainline code to resolve this issue. but my approach to address this was not up to date.

-Anand

author
#10 lore raw

PATCH v6 2/5 mmc: meson-gx: Use proper compatible string as per the dts

In reply to Anand Moon

Use proper compatible string as per the dts so that mmc driver could be tuned properly. SoC family S905, S905X have common clk tuning parameters setting, while AGX and G12 have common clk tuning parameters setting for mmc driver.

---
No changes.

---
 arch/arm/include/asm/arch-meson/sd_emmc.h |  7 ++++
 drivers/mmc/meson_gx_mmc.c                | 46 +++++++++++++++++------
 2 files changed, 41 insertions(+), 12 deletions(-)
arch/arm/include/asm/arch-meson/sd_emmc.h +7 -0
index f4299485dc..83142d5d3f 100644
@@ -13,6 +13,12 @@
 #define SDIO_PORT_B			1
 #define SDIO_PORT_C			2
 
+enum mmc_compatible {
+        MMC_COMPATIBLE_GXBB,
+        MMC_COMPATIBLE_GX,
+        MMC_COMPATIBLE_AXG,
+};
+
 #define SD_EMMC_CLKSRC_24M		24000000	/* 24 MHz */
 #define SD_EMMC_CLKSRC_DIV2		1000000000	/* 1 GHz */
 
@@ -87,6 +93,7 @@
 struct meson_mmc_platdata {
 	struct mmc_config cfg;
 	struct mmc mmc;
+	int compat;
 	void *regbase;
 	void *w_buf;
 };
drivers/mmc/meson_gx_mmc.c +34 -12

73 lines not on this page · raw message

Signature · 1 line
2.25.0
#11 lore raw

PATCH v6 2/5 mmc: meson-gx: Use proper compatible string as per the dts

Hi,

Quoted 111 lines · Anand Moon

Use proper compatible string as per the dts so that mmc driver could be tuned properly. SoC family S905, S905X have common clk tuning parameters setting, while AGX and G12 have common clk tuning parameters setting for mmc driver.

---
No changes.

---
 arch/arm/include/asm/arch-meson/sd_emmc.h |  7 ++++
 drivers/mmc/meson_gx_mmc.c                | 46 +++++++++++++++++------
 2 files changed, 41 insertions(+), 12 deletions(-)
arch/arm/include/asm/arch-meson/sd_emmc.h +7 -0
index f4299485dc..83142d5d3f 100644
@@ -13,6 +13,12 @@
 #define SDIO_PORT_B			1
 #define SDIO_PORT_C			2
 
+enum mmc_compatible {
+        MMC_COMPATIBLE_GXBB,
+        MMC_COMPATIBLE_GX,
+        MMC_COMPATIBLE_AXG,
+};
+
 #define SD_EMMC_CLKSRC_24M		24000000	/* 24 MHz */
 #define SD_EMMC_CLKSRC_DIV2		1000000000	/* 1 GHz */
 
@@ -87,6 +93,7 @@
 struct meson_mmc_platdata {
 	struct mmc_config cfg;
 	struct mmc mmc;
+	int compat;
 	void *regbase;
 	void *w_buf;
 };
drivers/mmc/meson_gx_mmc.c +30 -10
index b013c7c5fb..1aefe360c4 100644
@@ -37,7 +37,8 @@ static inline void meson_write(struct mmc *mmc, uint32_t val, int offset)
 	writel(val, get_regbase(mmc) + offset);
 }
 
-static void meson_mmc_config_clock(struct mmc *mmc)
+static void meson_mmc_config_clock(struct mmc *mmc,
+				   struct meson_mmc_platdata *pdata)
 {
 	uint32_t meson_mmc_clk = 0;
 	unsigned int clk, clk_src, clk_div;
@@ -66,14 +67,20 @@ static void meson_mmc_config_clock(struct mmc *mmc)
 	/* RX clock phase 0:180 */
 	meson_mmc_clk |= FIELD_PREP(CLK_RX_PHASE_MASK, CLK_PHASE_0);
 
-#ifdef CONFIG_MESON_GX
-	/* clk always on */
-	meson_mmc_clk |= CLK_V2_ALWAYS_ON;
-#endif
-#if (defined(CONFIG_MESON_AXG) || defined(CONFIG_MESON_G12A))
-	/* clk always on */
-	meson_mmc_clk |= CLK_V3_ALWAYS_ON;
-#endif
+	switch (pdata->compat) {
+	case MMC_COMPATIBLE_GXBB:
+	case MMC_COMPATIBLE_GX:
+		/* clk always on */
+		meson_mmc_clk |= CLK_V2_ALWAYS_ON;
+		break;
+	case MMC_COMPATIBLE_AXG:
+		/* clk always on */
+		meson_mmc_clk |= CLK_V3_ALWAYS_ON;
+		break;
+	default:
+		debug("no compatible supported");
+		break;
+	}
 
 	/* clock settings */
 	meson_mmc_clk |= clk_src;
@@ -85,9 +92,11 @@ static void meson_mmc_config_clock(struct mmc *mmc)
 static int meson_dm_mmc_set_ios(struct udevice *dev)
 {
 	struct mmc *mmc = mmc_get_mmc_dev(dev);
+	struct meson_mmc_platdata *pdata =
+		(struct meson_mmc_platdata *)dev_get_driver_data(dev);
 	uint32_t meson_mmc_cfg;
 
-	meson_mmc_config_clock(mmc);
+	meson_mmc_config_clock(mmc, pdata);
 
 	meson_mmc_cfg = meson_read(mmc, MESON_SD_EMMC_CFG);
 
@@ -324,9 +333,22 @@ int meson_mmc_bind(struct udevice *dev)
 	return mmc_bind(dev, &pdata->mmc, &pdata->cfg);
 }
 
+static const struct meson_mmc_platdata gxbb_data = {
+        .compat = MMC_COMPATIBLE_GXBB,
+};
+
+static const struct meson_mmc_platdata gx_data = {
+        .compat = MMC_COMPATIBLE_GX,
+};
+
+static const struct meson_mmc_platdata axg_data = {
+        .compat = MMC_COMPATIBLE_AXG,
+};

drivers/mmc/meson_gx_mmc.c int meson_mmc_bind(struct udevice *dev) · line 354

Quoted 10 lines
drivers/mmc/meson_gx_mmc.c +4 -2
+
 static const struct udevice_id meson_mmc_match[] = {
-	{ .compatible = "amlogic,meson-gx-mmc" },
-	{ .compatible = "amlogic,meson-axg-mmc" },
+	{ .compatible = "amlogic,meson-gxbb-mmc", .data = (ulong)&gxbb_data },
+	{ .compatible = "amlogic,meson-gx-mmc",	.data = (ulong)&gx_data },
+	{ .compatible = "amlogic,meson-axg-mmc", .data = (ulong)&axg_data },
 	{ /* sentinel */ }
 };
 

It's fine but you should do that before patch 1, and introduce the clk setup directly with the MMC_COMPATIBLE_*.

If you move it before, then:

Neil

author
#12 lore raw

PATCH v6 2/5 mmc: meson-gx: Use proper compatible string as per the dts

Hi Neil

Thanks for your review comments.

Quoted 120 lines · Neil Armstrong

Hi,

Quoted 116 lines · Anand Moon

Use proper compatible string as per the dts so that mmc driver could be tuned properly. SoC family S905, S905X have common clk tuning parameters setting, while AGX and G12 have common clk tuning parameters setting for mmc driver.

---
No changes.

---
 arch/arm/include/asm/arch-meson/sd_emmc.h |  7 ++++
 drivers/mmc/meson_gx_mmc.c                | 46 +++++++++++++++++------
 2 files changed, 41 insertions(+), 12 deletions(-)
arch/arm/include/asm/arch-meson/sd_emmc.h +7 -0
index f4299485dc..83142d5d3f 100644
@@ -13,6 +13,12 @@
 #define SDIO_PORT_B                  1
 #define SDIO_PORT_C                  2
 
+enum mmc_compatible {
+        MMC_COMPATIBLE_GXBB,
+        MMC_COMPATIBLE_GX,
+        MMC_COMPATIBLE_AXG,
+};
+
 #define SD_EMMC_CLKSRC_24M           24000000        /* 24 MHz */
 #define SD_EMMC_CLKSRC_DIV2          1000000000      /* 1 GHz */
 
@@ -87,6 +93,7 @@
 struct meson_mmc_platdata {
      struct mmc_config cfg;
      struct mmc mmc;
+     int compat;
      void *regbase;
      void *w_buf;
 };
drivers/mmc/meson_gx_mmc.c +33 -12
index b013c7c5fb..1aefe360c4 100644
@@ -37,7 +37,8 @@ static inline void meson_write(struct mmc *mmc, uint32_t val, int offset)
      writel(val, get_regbase(mmc) + offset);
 }
 
-static void meson_mmc_config_clock(struct mmc *mmc)
+static void meson_mmc_config_clock(struct mmc *mmc,
+                                struct meson_mmc_platdata *pdata)
 {
      uint32_t meson_mmc_clk = 0;
      unsigned int clk, clk_src, clk_div;
@@ -66,14 +67,20 @@ static void meson_mmc_config_clock(struct mmc *mmc)
      /* RX clock phase 0:180 */
      meson_mmc_clk |= FIELD_PREP(CLK_RX_PHASE_MASK, CLK_PHASE_0);
 
-#ifdef CONFIG_MESON_GX
-     /* clk always on */
-     meson_mmc_clk |= CLK_V2_ALWAYS_ON;
-#endif
-#if (defined(CONFIG_MESON_AXG) || defined(CONFIG_MESON_G12A))
-     /* clk always on */
-     meson_mmc_clk |= CLK_V3_ALWAYS_ON;
-#endif
+     switch (pdata->compat) {
+     case MMC_COMPATIBLE_GXBB:
+     case MMC_COMPATIBLE_GX:
+             /* clk always on */
+             meson_mmc_clk |= CLK_V2_ALWAYS_ON;
+             break;
+     case MMC_COMPATIBLE_AXG:
+             /* clk always on */
+             meson_mmc_clk |= CLK_V3_ALWAYS_ON;
+             break;
+     default:
+             debug("no compatible supported");
+             break;
+     }
 
      /* clock settings */
      meson_mmc_clk |= clk_src;
@@ -85,9 +92,11 @@ static void meson_mmc_config_clock(struct mmc *mmc)
 static int meson_dm_mmc_set_ios(struct udevice *dev)
 {
      struct mmc *mmc = mmc_get_mmc_dev(dev);
+     struct meson_mmc_platdata *pdata =
+             (struct meson_mmc_platdata *)dev_get_driver_data(dev);
      uint32_t meson_mmc_cfg;
 
-     meson_mmc_config_clock(mmc);
+     meson_mmc_config_clock(mmc, pdata);
 
      meson_mmc_cfg = meson_read(mmc, MESON_SD_EMMC_CFG);
 
@@ -324,9 +333,22 @@ int meson_mmc_bind(struct udevice *dev)
      return mmc_bind(dev, &pdata->mmc, &pdata->cfg);
 }
 
+static const struct meson_mmc_platdata gxbb_data = {
+        .compat = MMC_COMPATIBLE_GXBB,
+};
+
+static const struct meson_mmc_platdata gx_data = {
+        .compat = MMC_COMPATIBLE_GX,
+};
+
+static const struct meson_mmc_platdata axg_data = {
+        .compat = MMC_COMPATIBLE_AXG,
+};
+
 static const struct udevice_id meson_mmc_match[] = {
-     { .compatible = "amlogic,meson-gx-mmc" },
-     { .compatible = "amlogic,meson-axg-mmc" },
+     { .compatible = "amlogic,meson-gxbb-mmc", .data = (ulong)&gxbb_data },
+     { .compatible = "amlogic,meson-gx-mmc", .data = (ulong)&gx_data },
Quoted 9 lines

drivers/mmc/meson_gx_mmc.c int meson_mmc_bind(struct udevice *dev) · line 354

Quoted 5 lines
drivers/mmc/meson_gx_mmc.c +1 -0
+     { .compatible = "amlogic,meson-axg-mmc", .data = (ulong)&axg_data },
      { /* sentinel */ }
 };
 

It's fine but you should do that before patch 1, and introduce the clk setup directly with the MMC_COMPATIBLE_*.

Only GXBB and GLX have CLK_ALWAYS_ON(24) bit set
and AXG and G12X have CLK_ALWAYS_ON(28) bit set
for clk enable rest of the configuration is all most common for all the SoC. let keep this simple as of now.

Quoted 5 lines

If you move it before, then:

Neil

-Anand

#13 lore raw

PATCH v6 2/5 mmc: meson-gx: Use proper compatible string as per the dts

Quoted 135 lines · Anand Moon

Hi Neil

Thanks for your review comments.

Quoted 120 lines · Neil Armstrong

Hi,

Quoted 116 lines · Anand Moon

Use proper compatible string as per the dts so that mmc driver could be tuned properly. SoC family S905, S905X have common clk tuning parameters setting, while AGX and G12 have common clk tuning parameters setting for mmc driver.

---
No changes.

---
 arch/arm/include/asm/arch-meson/sd_emmc.h |  7 ++++
 drivers/mmc/meson_gx_mmc.c                | 46 +++++++++++++++++------
 2 files changed, 41 insertions(+), 12 deletions(-)
arch/arm/include/asm/arch-meson/sd_emmc.h +7 -0
index f4299485dc..83142d5d3f 100644
@@ -13,6 +13,12 @@
 #define SDIO_PORT_B                  1
 #define SDIO_PORT_C                  2
 
+enum mmc_compatible {
+        MMC_COMPATIBLE_GXBB,
+        MMC_COMPATIBLE_GX,
+        MMC_COMPATIBLE_AXG,
+};
+
 #define SD_EMMC_CLKSRC_24M           24000000        /* 24 MHz */
 #define SD_EMMC_CLKSRC_DIV2          1000000000      /* 1 GHz */
 
@@ -87,6 +93,7 @@
 struct meson_mmc_platdata {
      struct mmc_config cfg;
      struct mmc mmc;
+     int compat;
      void *regbase;
      void *w_buf;
 };
drivers/mmc/meson_gx_mmc.c +33 -12
index b013c7c5fb..1aefe360c4 100644
@@ -37,7 +37,8 @@ static inline void meson_write(struct mmc *mmc, uint32_t val, int offset)
      writel(val, get_regbase(mmc) + offset);
 }
 
-static void meson_mmc_config_clock(struct mmc *mmc)
+static void meson_mmc_config_clock(struct mmc *mmc,
+                                struct meson_mmc_platdata *pdata)
 {
      uint32_t meson_mmc_clk = 0;
      unsigned int clk, clk_src, clk_div;
@@ -66,14 +67,20 @@ static void meson_mmc_config_clock(struct mmc *mmc)
      /* RX clock phase 0:180 */
      meson_mmc_clk |= FIELD_PREP(CLK_RX_PHASE_MASK, CLK_PHASE_0);
 
-#ifdef CONFIG_MESON_GX
-     /* clk always on */
-     meson_mmc_clk |= CLK_V2_ALWAYS_ON;
-#endif
-#if (defined(CONFIG_MESON_AXG) || defined(CONFIG_MESON_G12A))
-     /* clk always on */
-     meson_mmc_clk |= CLK_V3_ALWAYS_ON;
-#endif
+     switch (pdata->compat) {
+     case MMC_COMPATIBLE_GXBB:
+     case MMC_COMPATIBLE_GX:
+             /* clk always on */
+             meson_mmc_clk |= CLK_V2_ALWAYS_ON;
+             break;
+     case MMC_COMPATIBLE_AXG:
+             /* clk always on */
+             meson_mmc_clk |= CLK_V3_ALWAYS_ON;
+             break;
+     default:
+             debug("no compatible supported");
+             break;
+     }
 
      /* clock settings */
      meson_mmc_clk |= clk_src;
@@ -85,9 +92,11 @@ static void meson_mmc_config_clock(struct mmc *mmc)
 static int meson_dm_mmc_set_ios(struct udevice *dev)
 {
      struct mmc *mmc = mmc_get_mmc_dev(dev);
+     struct meson_mmc_platdata *pdata =
+             (struct meson_mmc_platdata *)dev_get_driver_data(dev);
      uint32_t meson_mmc_cfg;
 
-     meson_mmc_config_clock(mmc);
+     meson_mmc_config_clock(mmc, pdata);
 
      meson_mmc_cfg = meson_read(mmc, MESON_SD_EMMC_CFG);
 
@@ -324,9 +333,22 @@ int meson_mmc_bind(struct udevice *dev)
      return mmc_bind(dev, &pdata->mmc, &pdata->cfg);
 }
 
+static const struct meson_mmc_platdata gxbb_data = {
+        .compat = MMC_COMPATIBLE_GXBB,
+};
+
+static const struct meson_mmc_platdata gx_data = {
+        .compat = MMC_COMPATIBLE_GX,
+};
+
+static const struct meson_mmc_platdata axg_data = {
+        .compat = MMC_COMPATIBLE_AXG,
+};
+a in 
 static const struct udevice_id meson_mmc_match[] = {
-     { .compatible = "amlogic,meson-gx-mmc" },
-     { .compatible = "amlogic,meson-axg-mmc" },
+     { .compatible = "amlogic,meson-gxbb-mmc", .data = (ulong)&gxbb_data },
+     { .compatible = "amlogic,meson-gx-mmc", .data = (ulong)&gx_data },
Quoted 9 lines

drivers/mmc/meson_gx_mmc.c int meson_mmc_bind(struct udevice *dev) · line 354

Quoted 5 lines
drivers/mmc/meson_gx_mmc.c +1 -0
+     { .compatible = "amlogic,meson-axg-mmc", .data = (ulong)&axg_data },
      { /* sentinel */ }
 };
 

It's fine but you should do that before patch 1, and introduce the clk setup directly with the MMC_COMPATIBLE_*.

Quoted 4 lines

Only GXBB and GLX have CLK_ALWAYS_ON(24) bit set
and AXG and G12X have CLK_ALWAYS_ON(28) bit set
for clk enable rest of the configuration is all most common for all the SoC. let keep this simple as of now.

It's not the point, just add the "struct meson_mmc_platdata" and .data in meson_mmc_match _before_ patch 1, to avoid adding hideous #ifdef/#elif/#endif in the meantime.

Neil

Quoted 10 lines
Quoted 7 lines

If you move it before, then:

Neil

-Anand

author
#14 lore raw

PATCH v6 3/5 arm: dts: gx: Move common nodes to the -u-boot.dtsi

In reply to Anand Moon

Move u-boot specific common nodes in the dts files to meson-gx-u-boot.dtsi. This allows us to keep the basic dts[i] files up-to-date with the ones in kernel, but at the same time allowing the u-boot to add its own properties to the existing nodes.
Also add missing mmc alias to dts nodes to avoid below debug warning.

mmc_bind: alias ret=-2, devnum=-1
mmc_bind: alias ret=-2, devnum=-1

---
no changes from previous

---
 arch/arm/dts/meson-gx-u-boot.dtsi             | 15 +++++++++++++++
 arch/arm/dts/meson-gxbb-nanopi-k2.dts         |  9 ---------
 arch/arm/dts/meson-gxbb-odroidc2.dts          |  9 ---------
 arch/arm/dts/meson-gxbb-p20x.dtsi             |  9 ---------
 arch/arm/dts/meson-gxl-s805x-libretech-ac.dts | 10 ----------
 arch/arm/dts/meson-gxl-s905x-khadas-vim.dts   |  5 -----
 arch/arm/dts/meson-gxl-s905x-libretech-cc.dts |  9 ---------
 arch/arm/dts/meson-gxl-s905x-p212.dtsi        | 10 ----------
 arch/arm/dts/meson-gxm-khadas-vim2.dts        | 10 ----------
 9 files changed, 15 insertions(+), 71 deletions(-)
arch/arm/dts/meson-gx-u-boot.dtsi +15 -0
index b84e5edba4..13be3a7b8f 100644
@@ -8,6 +8,21 @@
 	soc {
 		u-boot,dm-pre-reloc;
 	};
+
+	aliases {
+		serial0 = &uart_AO;
+		serial1 = &uart_A;
+		serial2 = &uart_AO_B;
+		ethernet0 = &ethmac;
+		spi0 = &spifc;
+		mmc0 = &sd_emmc_a;
+		mmc1 = &sd_emmc_b;
+		mmc2 = &sd_emmc_c;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
 };
 
 &vpu {
arch/arm/dts/meson-gxbb-nanopi-k2.dts +0 -9
index cbe99bd4e0..11690d6c46 100644
@@ -11,15 +11,6 @@
 / {
 	compatible = "friendlyarm,nanopi-k2", "amlogic,meson-gxbb";
 
-	aliases {
-		serial0 = &uart_AO;
-		ethernet0 = &ethmac;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
 	memory at 0 {
 		device_type = "memory";
 		reg = <0x0 0x0 0x0 0x80000000>;
arch/arm/dts/meson-gxbb-odroidc2.dts +0 -9
index 54954b314a..f8cd76a2ef 100644
@@ -14,15 +14,6 @@
 	compatible = "hardkernel,odroid-c2", "amlogic,meson-gxbb";
 	model = "Hardkernel ODROID-C2";
 
-	aliases {
-		serial0 = &uart_AO;
-		ethernet0 = &ethmac;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
 	memory at 0 {
 		device_type = "memory";
 		reg = <0x0 0x0 0x0 0x80000000>;
arch/arm/dts/meson-gxbb-p20x.dtsi +0 -9
index 0be0f2a5d2..c9822e50f9 100644
@@ -8,15 +8,6 @@
 #include "meson-gxbb.dtsi"
 
 / {
-	aliases {
-		serial0 = &uart_AO;
-		ethernet0 = &ethmac;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
 	memory at 0 {
 		device_type = "memory";
 		reg = <0x0 0x0 0x0 0x40000000>;
arch/arm/dts/meson-gxl-s805x-libretech-ac.dts +0 -10
index 82b1c48511..4f9072a83e 100644
@@ -16,16 +16,6 @@
 		     "amlogic,meson-gxl";
 	model = "Libre Computer Board AML-S805X-AC";
 
-	aliases {
-		serial0 = &uart_AO;
-		ethernet0 = &ethmac;
-		spi0 = &spifc;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
 	cvbs-connector {
 		/*
 		 * The pads are present but no connector is soldered on
arch/arm/dts/meson-gxl-s905x-khadas-vim.dts +0 -5
index ceb34afe42..072e4575d2 100644
@@ -26,11 +26,6 @@
 		};
 	};
 
-	aliases {
-		serial2 = &uart_AO_B;
-		ethernet0 = &ethmac;
-	};
-
 	gpio-keys-polled {
 		compatible = "gpio-keys-polled";
 		#address-cells = <1>;
arch/arm/dts/meson-gxl-s905x-libretech-cc.dts +0 -9
index a23252efc6..8d3965ab42 100644
@@ -15,15 +15,6 @@
 	compatible = "libretech,cc", "amlogic,s905x", "amlogic,meson-gxl";
 	model = "Libre Computer Board AML-S905X-CC";
 
-	aliases {
-		serial0 = &uart_AO;
-		ethernet0 = &ethmac;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
 	cvbs-connector {
 		compatible = "composite-video-connector";
 
arch/arm/dts/meson-gxl-s905x-p212.dtsi +0 -10
index a1b31013ab..70f437fc3a 100644
@@ -13,16 +13,6 @@
 #include "meson-gxl-s905x.dtsi"
 
 / {
-	aliases {
-		serial0 = &uart_AO;
-		serial1 = &uart_A;
-		ethernet0 = &ethmac;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
 	memory at 0 {
 		device_type = "memory";
 		reg = <0x0 0x0 0x0 0x80000000>;
arch/arm/dts/meson-gxm-khadas-vim2.dts +0 -10
index 782e9edac8..4e68e289d3 100644
@@ -16,16 +16,6 @@
 	compatible = "khadas,vim2", "amlogic,s912", "amlogic,meson-gxm";
 	model = "Khadas VIM2";
 
-	aliases {
-		serial0 = &uart_AO;
-		serial1 = &uart_A;
-		serial2 = &uart_AO_B;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
 	memory at 0 {
 		device_type = "memory";
 		reg = <0x0 0x0 0x0 0x80000000>;
Signature · 1 line
2.25.0
#15 lore raw

PATCH v6 3/5 arm: dts: gx: Move common nodes to the -u-boot.dtsi

Hi,

Quoted 10 lines · Anand Moon

Move u-boot specific common nodes in the dts files to meson-gx-u-boot.dtsi. This allows us to keep the basic dts[i] files up-to-date with the ones in kernel, but at the same time allowing the u-boot to add its own properties to the existing nodes.
Also add missing mmc alias to dts nodes to avoid below debug warning.

mmc_bind: alias ret=-2, devnum=-1
mmc_bind: alias ret=-2, devnum=-1

The mmc aliases are u-boot specific, so only those should be moved into the meson-gx-u-boot.dtsi.

Please keep the other aliases in the their linux sync'ed files.

Neil

Quoted 202 lines

---
no changes from previous

---
 arch/arm/dts/meson-gx-u-boot.dtsi             | 15 +++++++++++++++
 arch/arm/dts/meson-gxbb-nanopi-k2.dts         |  9 ---------
 arch/arm/dts/meson-gxbb-odroidc2.dts          |  9 ---------
 arch/arm/dts/meson-gxbb-p20x.dtsi             |  9 ---------
 arch/arm/dts/meson-gxl-s805x-libretech-ac.dts | 10 ----------
 arch/arm/dts/meson-gxl-s905x-khadas-vim.dts   |  5 -----
 arch/arm/dts/meson-gxl-s905x-libretech-cc.dts |  9 ---------
 arch/arm/dts/meson-gxl-s905x-p212.dtsi        | 10 ----------
 arch/arm/dts/meson-gxm-khadas-vim2.dts        | 10 ----------
 9 files changed, 15 insertions(+), 71 deletions(-)
arch/arm/dts/meson-gx-u-boot.dtsi +15 -0
index b84e5edba4..13be3a7b8f 100644
@@ -8,6 +8,21 @@
 	soc {
 		u-boot,dm-pre-reloc;
 	};
+
+	aliases {
+		serial0 = &uart_AO;
+		serial1 = &uart_A;
+		serial2 = &uart_AO_B;
+		ethernet0 = &ethmac;
+		spi0 = &spifc;
+		mmc0 = &sd_emmc_a;
+		mmc1 = &sd_emmc_b;
+		mmc2 = &sd_emmc_c;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
 };
 
 &vpu {
arch/arm/dts/meson-gxbb-nanopi-k2.dts +0 -9
index cbe99bd4e0..11690d6c46 100644
@@ -11,15 +11,6 @@
 / {
 	compatible = "friendlyarm,nanopi-k2", "amlogic,meson-gxbb";
 
-	aliases {
-		serial0 = &uart_AO;
-		ethernet0 = &ethmac;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
 	memory at 0 {
 		device_type = "memory";
 		reg = <0x0 0x0 0x0 0x80000000>;
arch/arm/dts/meson-gxbb-odroidc2.dts +0 -9
index 54954b314a..f8cd76a2ef 100644
@@ -14,15 +14,6 @@
 	compatible = "hardkernel,odroid-c2", "amlogic,meson-gxbb";
 	model = "Hardkernel ODROID-C2";
 
-	aliases {
-		serial0 = &uart_AO;
-		ethernet0 = &ethmac;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
 	memory at 0 {
 		device_type = "memory";
 		reg = <0x0 0x0 0x0 0x80000000>;
arch/arm/dts/meson-gxbb-p20x.dtsi +0 -9
index 0be0f2a5d2..c9822e50f9 100644
@@ -8,15 +8,6 @@
 #include "meson-gxbb.dtsi"
 
 / {
-	aliases {
-		serial0 = &uart_AO;
-		ethernet0 = &ethmac;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
 	memory at 0 {
 		device_type = "memory";
 		reg = <0x0 0x0 0x0 0x40000000>;
arch/arm/dts/meson-gxl-s805x-libretech-ac.dts +0 -10
index 82b1c48511..4f9072a83e 100644
@@ -16,16 +16,6 @@
 		     "amlogic,meson-gxl";
 	model = "Libre Computer Board AML-S805X-AC";
 
-	aliases {
-		serial0 = &uart_AO;
-		ethernet0 = &ethmac;
-		spi0 = &spifc;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
 	cvbs-connector {
 		/*
 		 * The pads are present but no connector is soldered on
arch/arm/dts/meson-gxl-s905x-khadas-vim.dts +0 -5
index ceb34afe42..072e4575d2 100644
@@ -26,11 +26,6 @@
 		};
 	};
 
-	aliases {
-		serial2 = &uart_AO_B;
-		ethernet0 = &ethmac;
-	};
-
 	gpio-keys-polled {
 		compatible = "gpio-keys-polled";
 		#address-cells = <1>;
arch/arm/dts/meson-gxl-s905x-libretech-cc.dts +0 -9
index a23252efc6..8d3965ab42 100644
@@ -15,15 +15,6 @@
 	compatible = "libretech,cc", "amlogic,s905x", "amlogic,meson-gxl";
 	model = "Libre Computer Board AML-S905X-CC";
 
-	aliases {
-		serial0 = &uart_AO;
-		ethernet0 = &ethmac;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
 	cvbs-connector {
 		compatible = "composite-video-connector";
 
arch/arm/dts/meson-gxl-s905x-p212.dtsi +0 -10
index a1b31013ab..70f437fc3a 100644
@@ -13,16 +13,6 @@
 #include "meson-gxl-s905x.dtsi"
 
 / {
-	aliases {
-		serial0 = &uart_AO;
-		serial1 = &uart_A;
-		ethernet0 = &ethmac;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
 	memory at 0 {
 		device_type = "memory";
 		reg = <0x0 0x0 0x0 0x80000000>;
arch/arm/dts/meson-gxm-khadas-vim2.dts +0 -10
index 782e9edac8..4e68e289d3 100644
@@ -16,16 +16,6 @@
 	compatible = "khadas,vim2", "amlogic,s912", "amlogic,meson-gxm";
 	model = "Khadas VIM2";
 
-	aliases {
-		serial0 = &uart_AO;
-		serial1 = &uart_A;
-		serial2 = &uart_AO_B;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
 	memory at 0 {
 		device_type = "memory";
 		reg = <0x0 0x0 0x0 0x80000000>;
author
#16 lore raw

PATCH v6 3/5 arm: dts: gx: Move common nodes to the -u-boot.dtsi

Hi Neil,

Thanks for your review.

Quoted 15 lines · Neil Armstrong

Hi,

Quoted 10 lines · Anand Moon

Move u-boot specific common nodes in the dts files to meson-gx-u-boot.dtsi. This allows us to keep the basic dts[i] files up-to-date with the ones in kernel, but at the same time allowing the u-boot to add its own properties to the existing nodes.
Also add missing mmc alias to dts nodes to avoid below debug warning.

mmc_bind: alias ret=-2, devnum=-1
mmc_bind: alias ret=-2, devnum=-1

Quoted 7 lines

The mmc aliases are u-boot specific, so only those should be moved into the meson-gx-u-boot.dtsi.

Please keep the other aliases in the their linux sync'ed files.

Neil

meson-gx-u-boot.dtsi is included in following dts file so their is no another common -u-boot.dtsi for all the SBC dts.

$ git grep meson-gx-u-boot.dtsi
arch/arm/dts/meson-gxbb-nanopi-k2-u-boot.dtsi:#include "meson-gx-u-boot.dtsi"
arch/arm/dts/meson-gxbb-odroidc2-u-boot.dtsi:#include "meson-gx-u-boot.dtsi"
arch/arm/dts/meson-gxbb-p200-u-boot.dtsi:#include "meson-gx-u-boot.dtsi"
arch/arm/dts/meson-gxbb-p201-u-boot.dtsi:#include "meson-gx-u-boot.dtsi"
arch/arm/dts/meson-gxl-s905x-khadas-vim-u-boot.dtsi:#include
"meson-gx-u-boot.dtsi"
arch/arm/dts/meson-gxl-s905x-libretech-cc-u-boot.dtsi:#include
"meson-gx-u-boot.dtsi"
arch/arm/dts/meson-gxl-s905x-p212-u-boot.dtsi:#include "meson-gx-u-boot.dtsi"
arch/arm/dts/meson-gxm-khadas-vim2-u-boot.dtsi:#include "meson-gx-u-boot.dtsi"

So all the common nodes is included in *meson-gx-u-boot.dtsi* for GXBB and GXL dts.

-Anand

Quoted 202 lines
Quoted 202 lines

---
no changes from previous

---
 arch/arm/dts/meson-gx-u-boot.dtsi             | 15 +++++++++++++++
 arch/arm/dts/meson-gxbb-nanopi-k2.dts         |  9 ---------
 arch/arm/dts/meson-gxbb-odroidc2.dts          |  9 ---------
 arch/arm/dts/meson-gxbb-p20x.dtsi             |  9 ---------
 arch/arm/dts/meson-gxl-s805x-libretech-ac.dts | 10 ----------
 arch/arm/dts/meson-gxl-s905x-khadas-vim.dts   |  5 -----
 arch/arm/dts/meson-gxl-s905x-libretech-cc.dts |  9 ---------
 arch/arm/dts/meson-gxl-s905x-p212.dtsi        | 10 ----------
 arch/arm/dts/meson-gxm-khadas-vim2.dts        | 10 ----------
 9 files changed, 15 insertions(+), 71 deletions(-)
arch/arm/dts/meson-gx-u-boot.dtsi +15 -0
index b84e5edba4..13be3a7b8f 100644
@@ -8,6 +8,21 @@
      soc {
              u-boot,dm-pre-reloc;
      };
+
+     aliases {
+             serial0 = &uart_AO;
+             serial1 = &uart_A;
+             serial2 = &uart_AO_B;
+             ethernet0 = &ethmac;
+             spi0 = &spifc;
+             mmc0 = &sd_emmc_a;
+             mmc1 = &sd_emmc_b;
+             mmc2 = &sd_emmc_c;
+     };
+
+     chosen {
+             stdout-path = "serial0:115200n8";
+     };
 };
 
 &vpu {
arch/arm/dts/meson-gxbb-nanopi-k2.dts +0 -9
index cbe99bd4e0..11690d6c46 100644
@@ -11,15 +11,6 @@
 / {
      compatible = "friendlyarm,nanopi-k2", "amlogic,meson-gxbb";
 
-     aliases {
-             serial0 = &uart_AO;
-             ethernet0 = &ethmac;
-     };
-
-     chosen {
-             stdout-path = "serial0:115200n8";
-     };
-
      memory at 0 {
              device_type = "memory";
              reg = <0x0 0x0 0x0 0x80000000>;
arch/arm/dts/meson-gxbb-odroidc2.dts +0 -9
index 54954b314a..f8cd76a2ef 100644
@@ -14,15 +14,6 @@
      compatible = "hardkernel,odroid-c2", "amlogic,meson-gxbb";
      model = "Hardkernel ODROID-C2";
 
-     aliases {
-             serial0 = &uart_AO;
-             ethernet0 = &ethmac;
-     };
-
-     chosen {
-             stdout-path = "serial0:115200n8";
-     };
-
      memory at 0 {
              device_type = "memory";
              reg = <0x0 0x0 0x0 0x80000000>;
arch/arm/dts/meson-gxbb-p20x.dtsi +0 -9
index 0be0f2a5d2..c9822e50f9 100644
@@ -8,15 +8,6 @@
 #include "meson-gxbb.dtsi"
 
 / {
-     aliases {
-             serial0 = &uart_AO;
-             ethernet0 = &ethmac;
-     };
-
-     chosen {
-             stdout-path = "serial0:115200n8";
-     };
-
      memory at 0 {
              device_type = "memory";
              reg = <0x0 0x0 0x0 0x40000000>;
arch/arm/dts/meson-gxl-s805x-libretech-ac.dts +0 -10
index 82b1c48511..4f9072a83e 100644
@@ -16,16 +16,6 @@
                   "amlogic,meson-gxl";
      model = "Libre Computer Board AML-S805X-AC";
 
-     aliases {
-             serial0 = &uart_AO;
-             ethernet0 = &ethmac;
-             spi0 = &spifc;
-     };
-
-     chosen {
-             stdout-path = "serial0:115200n8";
-     };
-
      cvbs-connector {
              /*
               * The pads are present but no connector is soldered on
arch/arm/dts/meson-gxl-s905x-khadas-vim.dts +0 -5
index ceb34afe42..072e4575d2 100644
@@ -26,11 +26,6 @@
              };
      };
 
-     aliases {
-             serial2 = &uart_AO_B;
-             ethernet0 = &ethmac;
-     };
-
      gpio-keys-polled {
              compatible = "gpio-keys-polled";
              #address-cells = <1>;
arch/arm/dts/meson-gxl-s905x-libretech-cc.dts +0 -9
index a23252efc6..8d3965ab42 100644
@@ -15,15 +15,6 @@
      compatible = "libretech,cc", "amlogic,s905x", "amlogic,meson-gxl";
      model = "Libre Computer Board AML-S905X-CC";
 
-     aliases {
-             serial0 = &uart_AO;
-             ethernet0 = &ethmac;
-     };
-
-     chosen {
-             stdout-path = "serial0:115200n8";
-     };
-
      cvbs-connector {
              compatible = "composite-video-connector";
 
arch/arm/dts/meson-gxl-s905x-p212.dtsi +0 -10
index a1b31013ab..70f437fc3a 100644
@@ -13,16 +13,6 @@
 #include "meson-gxl-s905x.dtsi"
 
 / {
-     aliases {
-             serial0 = &uart_AO;
-             serial1 = &uart_A;
-             ethernet0 = &ethmac;
-     };
-
-     chosen {
-             stdout-path = "serial0:115200n8";
-     };
-
      memory at 0 {
              device_type = "memory";
              reg = <0x0 0x0 0x0 0x80000000>;
arch/arm/dts/meson-gxm-khadas-vim2.dts +0 -10
index 782e9edac8..4e68e289d3 100644
@@ -16,16 +16,6 @@
      compatible = "khadas,vim2", "amlogic,s912", "amlogic,meson-gxm";
      model = "Khadas VIM2";
 
-     aliases {
-             serial0 = &uart_AO;
-             serial1 = &uart_A;
-             serial2 = &uart_AO_B;
-     };
-
-     chosen {
-             stdout-path = "serial0:115200n8";
-     };
-
      memory at 0 {
              device_type = "memory";
              reg = <0x0 0x0 0x0 0x80000000>;
#17 lore raw

PATCH v6 3/5 arm: dts: gx: Move common nodes to the -u-boot.dtsi

Quoted 43 lines · Anand Moon

Hi Neil,

Thanks for your review.

Quoted 15 lines · Neil Armstrong

Hi,

Quoted 10 lines · Anand Moon

Move u-boot specific common nodes in the dts files to meson-gx-u-boot.dtsi. This allows us to keep the basic dts[i] files up-to-date with the ones in kernel, but at the same time allowing the u-boot to add its own properties to the existing nodes.
Also add missing mmc alias to dts nodes to avoid below debug warning.

mmc_bind: alias ret=-2, devnum=-1
mmc_bind: alias ret=-2, devnum=-1

Quoted 7 lines

The mmc aliases are u-boot specific, so only those should be moved into the meson-gx-u-boot.dtsi.

Please keep the other aliases in the their linux sync'ed files.

Neil

meson-gx-u-boot.dtsi is included in following dts file so their is no another common -u-boot.dtsi for all the SBC dts.

$ git grep meson-gx-u-boot.dtsi
arch/arm/dts/meson-gxbb-nanopi-k2-u-boot.dtsi:#include "meson-gx-u-boot.dtsi"
arch/arm/dts/meson-gxbb-odroidc2-u-boot.dtsi:#include "meson-gx-u-boot.dtsi"
arch/arm/dts/meson-gxbb-p200-u-boot.dtsi:#include "meson-gx-u-boot.dtsi"
arch/arm/dts/meson-gxbb-p201-u-boot.dtsi:#include "meson-gx-u-boot.dtsi"
arch/arm/dts/meson-gxl-s905x-khadas-vim-u-boot.dtsi:#include
"meson-gx-u-boot.dtsi"
arch/arm/dts/meson-gxl-s905x-libretech-cc-u-boot.dtsi:#include
"meson-gx-u-boot.dtsi"
arch/arm/dts/meson-gxl-s905x-p212-u-boot.dtsi:#include "meson-gx-u-boot.dtsi"
arch/arm/dts/meson-gxm-khadas-vim2-u-boot.dtsi:#include "meson-gx-u-boot.dtsi"
Quoted 2 lines

So all the common nodes is included in *meson-gx-u-boot.dtsi* for GXBB and GXL dts.

It's not the point.

The goal is to keep the dts and dtsi files untouched to be able to sync them from linux easily.

So :
- all general changes/fixes must go through linux, and temporary in the -u-boot.dtsi
- all u-boot specific in the -u-boot.dtsi

If you have an issue with the aliases, please discuss it on the linux-amlogic ML, but the linux policy is to only declare the needed aliases in the boards dts and avoid having a bunch of aliases in the dtsi files.

Neil

Quoted 207 lines

-Anand

Quoted 202 lines
Quoted 202 lines

---
no changes from previous

---
 arch/arm/dts/meson-gx-u-boot.dtsi             | 15 +++++++++++++++
 arch/arm/dts/meson-gxbb-nanopi-k2.dts         |  9 ---------
 arch/arm/dts/meson-gxbb-odroidc2.dts          |  9 ---------
 arch/arm/dts/meson-gxbb-p20x.dtsi             |  9 ---------
 arch/arm/dts/meson-gxl-s805x-libretech-ac.dts | 10 ----------
 arch/arm/dts/meson-gxl-s905x-khadas-vim.dts   |  5 -----
 arch/arm/dts/meson-gxl-s905x-libretech-cc.dts |  9 ---------
 arch/arm/dts/meson-gxl-s905x-p212.dtsi        | 10 ----------
 arch/arm/dts/meson-gxm-khadas-vim2.dts        | 10 ----------
 9 files changed, 15 insertions(+), 71 deletions(-)
arch/arm/dts/meson-gx-u-boot.dtsi +15 -0
index b84e5edba4..13be3a7b8f 100644
@@ -8,6 +8,21 @@
      soc {
              u-boot,dm-pre-reloc;
      };
+
+     aliases {
+             serial0 = &uart_AO;
+             serial1 = &uart_A;
+             serial2 = &uart_AO_B;
+             ethernet0 = &ethmac;
+             spi0 = &spifc;
+             mmc0 = &sd_emmc_a;
+             mmc1 = &sd_emmc_b;
+             mmc2 = &sd_emmc_c;
+     };
+
+     chosen {
+             stdout-path = "serial0:115200n8";
+     };
 };
 
 &vpu {
arch/arm/dts/meson-gxbb-nanopi-k2.dts +0 -9
index cbe99bd4e0..11690d6c46 100644
@@ -11,15 +11,6 @@
 / {
      compatible = "friendlyarm,nanopi-k2", "amlogic,meson-gxbb";
 
-     aliases {
-             serial0 = &uart_AO;
-             ethernet0 = &ethmac;
-     };
-
-     chosen {
-             stdout-path = "serial0:115200n8";
-     };
-
      memory at 0 {
              device_type = "memory";
              reg = <0x0 0x0 0x0 0x80000000>;
arch/arm/dts/meson-gxbb-odroidc2.dts +0 -9
index 54954b314a..f8cd76a2ef 100644
@@ -14,15 +14,6 @@
      compatible = "hardkernel,odroid-c2", "amlogic,meson-gxbb";
      model = "Hardkernel ODROID-C2";
 
-     aliases {
-             serial0 = &uart_AO;
-             ethernet0 = &ethmac;
-     };
-
-     chosen {
-             stdout-path = "serial0:115200n8";
-     };
-
      memory at 0 {
              device_type = "memory";
              reg = <0x0 0x0 0x0 0x80000000>;
arch/arm/dts/meson-gxbb-p20x.dtsi +0 -9
index 0be0f2a5d2..c9822e50f9 100644
@@ -8,15 +8,6 @@
 #include "meson-gxbb.dtsi"
 
 / {
-     aliases {
-             serial0 = &uart_AO;
-             ethernet0 = &ethmac;
-     };
-
-     chosen {
-             stdout-path = "serial0:115200n8";
-     };
-
      memory at 0 {
              device_type = "memory";
              reg = <0x0 0x0 0x0 0x40000000>;
arch/arm/dts/meson-gxl-s805x-libretech-ac.dts +0 -10
index 82b1c48511..4f9072a83e 100644
@@ -16,16 +16,6 @@
                   "amlogic,meson-gxl";
      model = "Libre Computer Board AML-S805X-AC";
 
-     aliases {
-             serial0 = &uart_AO;
-             ethernet0 = &ethmac;
-             spi0 = &spifc;
-     };
-
-     chosen {
-             stdout-path = "serial0:115200n8";
-     };
-
      cvbs-connector {
              /*
               * The pads are present but no connector is soldered on
arch/arm/dts/meson-gxl-s905x-khadas-vim.dts +0 -5
index ceb34afe42..072e4575d2 100644
@@ -26,11 +26,6 @@
              };
      };
 
-     aliases {
-             serial2 = &uart_AO_B;
-             ethernet0 = &ethmac;
-     };
-
      gpio-keys-polled {
              compatible = "gpio-keys-polled";
              #address-cells = <1>;
arch/arm/dts/meson-gxl-s905x-libretech-cc.dts +0 -9
index a23252efc6..8d3965ab42 100644
@@ -15,15 +15,6 @@
      compatible = "libretech,cc", "amlogic,s905x", "amlogic,meson-gxl";
      model = "Libre Computer Board AML-S905X-CC";
 
-     aliases {
-             serial0 = &uart_AO;
-             ethernet0 = &ethmac;
-     };
-
-     chosen {
-             stdout-path = "serial0:115200n8";
-     };
-
      cvbs-connector {
              compatible = "composite-video-connector";
 
arch/arm/dts/meson-gxl-s905x-p212.dtsi +0 -10
index a1b31013ab..70f437fc3a 100644
@@ -13,16 +13,6 @@
 #include "meson-gxl-s905x.dtsi"
 
 / {
-     aliases {
-             serial0 = &uart_AO;
-             serial1 = &uart_A;
-             ethernet0 = &ethmac;
-     };
-
-     chosen {
-             stdout-path = "serial0:115200n8";
-     };
-
      memory at 0 {
              device_type = "memory";
              reg = <0x0 0x0 0x0 0x80000000>;
arch/arm/dts/meson-gxm-khadas-vim2.dts +0 -10
index 782e9edac8..4e68e289d3 100644
@@ -16,16 +16,6 @@
      compatible = "khadas,vim2", "amlogic,s912", "amlogic,meson-gxm";
      model = "Khadas VIM2";
 
-     aliases {
-             serial0 = &uart_AO;
-             serial1 = &uart_A;
-             serial2 = &uart_AO_B;
-     };
-
-     chosen {
-             stdout-path = "serial0:115200n8";
-     };
-
      memory at 0 {
              device_type = "memory";
              reg = <0x0 0x0 0x0 0x80000000>;
author
#18 lore raw

PATCH v6 4/5 arm: dts: g12: Move common nodes to the -u-boot.dtsi

In reply to Anand Moon

Move u-boot specific common nodes in the dts files to meson-g12-common-u-boot.dtsi. This allows us to keep the basic dts[i] files up-to-date with the ones in kernel,
but at the same time allowing the u-boot to add its own properties to the existing nodes.
Also add missing mmc alias to dts nodes to avoid below debug warning.

mmc_bind: alias ret=-2, devnum=-1
mmc_bind: alias ret=-2, devnum=-1

---
No changes from previous patch

---
 arch/arm/dts/meson-g12-common-u-boot.dtsi | 12 ++++++++++++
 arch/arm/dts/meson-g12a-sei510.dts        |  9 ---------
 arch/arm/dts/meson-g12a-u200.dts          |  9 ---------
 arch/arm/dts/meson-g12b-odroid-n2.dts     |  9 ---------
 arch/arm/dts/meson-khadas-vim3.dtsi       |  9 ---------
 arch/arm/dts/meson-sm1-sei610.dts         |  9 ---------
 6 files changed, 12 insertions(+), 45 deletions(-)
arch/arm/dts/meson-g12-common-u-boot.dtsi +12 -0
index 38fd3d3feb..347b8ded22 100644
@@ -8,6 +8,18 @@
 	soc {
 		u-boot,dm-pre-reloc;
 	};
+
+	aliases {
+		serial0 = &uart_AO;
+		ethernet0 = &ethmac;
+		mmc0 = &sd_emmc_a;
+		mmc1 = &sd_emmc_b;
+		mmc2 = &sd_emmc_c;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
 };
 
 &canvas {
arch/arm/dts/meson-g12a-sei510.dts +0 -9
index c7a8736885..c6a48ebbe5 100644
@@ -28,11 +28,6 @@
 		};
 	};
 
-	aliases {
-		serial0 = &uart_AO;
-		ethernet0 = &ethmac;
-	};
-
 	mono_dac: audio-codec-0 {
 		compatible = "maxim,max98357a";
 		#sound-dai-cells = <0>;
@@ -49,10 +44,6 @@
 		sound-name-prefix = "MIC";
 	};
 
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
 	cvbs-connector {
 		compatible = "composite-video-connector";
 
arch/arm/dts/meson-g12a-u200.dts +0 -9
index 8551fbd4a4..8be7b6985b 100644
@@ -13,15 +13,6 @@
 	compatible = "amlogic,u200", "amlogic,g12a";
 	model = "Amlogic Meson G12A U200 Development Board";
 
-	aliases {
-		serial0 = &uart_AO;
-		ethernet0 = &ethmac;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
 	cvbs-connector {
 		compatible = "composite-video-connector";
 
arch/arm/dts/meson-g12b-odroid-n2.dts +0 -9
index 42f1540575..a37f66a5e0 100644
@@ -15,15 +15,6 @@
 	compatible = "hardkernel,odroid-n2", "amlogic,g12b";
 	model = "Hardkernel ODROID-N2";
 
-	aliases {
-		serial0 = &uart_AO;
-		ethernet0 = &ethmac;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
 	memory at 0 {
 		device_type = "memory";
 		reg = <0x0 0x0 0x0 0x40000000>;
arch/arm/dts/meson-khadas-vim3.dtsi +0 -9
index 8647da7d66..c6b0ce9a88 100644
@@ -11,15 +11,6 @@
 / {
 	model = "Khadas VIM3";
 
-	aliases {
-		serial0 = &uart_AO;
-		ethernet0 = &ethmac;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
 	memory at 0 {
 		device_type = "memory";
 		reg = <0x0 0x0 0x0 0x80000000>;
arch/arm/dts/meson-sm1-sei610.dts +0 -9
index 3435aaa4e8..4372708811 100644
@@ -14,15 +14,6 @@
 	compatible = "seirobotics,sei610", "amlogic,sm1";
 	model = "SEI Robotics SEI610";
 
-	aliases {
-		serial0 = &uart_AO;
-		ethernet0 = &ethmac;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
 	emmc_pwrseq: emmc-pwrseq {
 		compatible = "mmc-pwrseq-emmc";
 		reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
Signature · 1 line
2.25.0
#19 lore raw

PATCH v6 4/5 arm: dts: g12: Move common nodes to the -u-boot.dtsi

Hi,

Quoted 10 lines · Anand Moon

Move u-boot specific common nodes in the dts files to meson-g12-common-u-boot.dtsi. This allows us to keep the basic dts[i] files up-to-date with the ones in kernel,
but at the same time allowing the u-boot to add its own properties to the existing nodes.
Also add missing mmc alias to dts nodes to avoid below debug warning.

mmc_bind: alias ret=-2, devnum=-1
mmc_bind: alias ret=-2, devnum=-1

Same as patch 4.

Neil

Quoted 144 lines

---
No changes from previous patch

---
 arch/arm/dts/meson-g12-common-u-boot.dtsi | 12 ++++++++++++
 arch/arm/dts/meson-g12a-sei510.dts        |  9 ---------
 arch/arm/dts/meson-g12a-u200.dts          |  9 ---------
 arch/arm/dts/meson-g12b-odroid-n2.dts     |  9 ---------
 arch/arm/dts/meson-khadas-vim3.dtsi       |  9 ---------
 arch/arm/dts/meson-sm1-sei610.dts         |  9 ---------
 6 files changed, 12 insertions(+), 45 deletions(-)
arch/arm/dts/meson-g12-common-u-boot.dtsi +12 -0
index 38fd3d3feb..347b8ded22 100644
@@ -8,6 +8,18 @@
 	soc {
 		u-boot,dm-pre-reloc;
 	};
+
+	aliases {
+		serial0 = &uart_AO;
+		ethernet0 = &ethmac;
+		mmc0 = &sd_emmc_a;
+		mmc1 = &sd_emmc_b;
+		mmc2 = &sd_emmc_c;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
 };
 
 &canvas {
arch/arm/dts/meson-g12a-sei510.dts +0 -9
index c7a8736885..c6a48ebbe5 100644
@@ -28,11 +28,6 @@
 		};
 	};
 
-	aliases {
-		serial0 = &uart_AO;
-		ethernet0 = &ethmac;
-	};
-
 	mono_dac: audio-codec-0 {
 		compatible = "maxim,max98357a";
 		#sound-dai-cells = <0>;
@@ -49,10 +44,6 @@
 		sound-name-prefix = "MIC";
 	};
 
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
 	cvbs-connector {
 		compatible = "composite-video-connector";
 
arch/arm/dts/meson-g12a-u200.dts +0 -9
index 8551fbd4a4..8be7b6985b 100644
@@ -13,15 +13,6 @@
 	compatible = "amlogic,u200", "amlogic,g12a";
 	model = "Amlogic Meson G12A U200 Development Board";
 
-	aliases {
-		serial0 = &uart_AO;
-		ethernet0 = &ethmac;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
 	cvbs-connector {
 		compatible = "composite-video-connector";
 
arch/arm/dts/meson-g12b-odroid-n2.dts +0 -9
index 42f1540575..a37f66a5e0 100644
@@ -15,15 +15,6 @@
 	compatible = "hardkernel,odroid-n2", "amlogic,g12b";
 	model = "Hardkernel ODROID-N2";
 
-	aliases {
-		serial0 = &uart_AO;
-		ethernet0 = &ethmac;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
 	memory at 0 {
 		device_type = "memory";
 		reg = <0x0 0x0 0x0 0x40000000>;
arch/arm/dts/meson-khadas-vim3.dtsi +0 -9
index 8647da7d66..c6b0ce9a88 100644
@@ -11,15 +11,6 @@
 / {
 	model = "Khadas VIM3";
 
-	aliases {
-		serial0 = &uart_AO;
-		ethernet0 = &ethmac;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
 	memory at 0 {
 		device_type = "memory";
 		reg = <0x0 0x0 0x0 0x80000000>;
arch/arm/dts/meson-sm1-sei610.dts +0 -9
index 3435aaa4e8..4372708811 100644
@@ -14,15 +14,6 @@
 	compatible = "seirobotics,sei610", "amlogic,sm1";
 	model = "SEI Robotics SEI610";
 
-	aliases {
-		serial0 = &uart_AO;
-		ethernet0 = &ethmac;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
 	emmc_pwrseq: emmc-pwrseq {
 		compatible = "mmc-pwrseq-emmc";
 		reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
author
#20 lore raw

PATCH v6 4/5 arm: dts: g12: Move common nodes to the -u-boot.dtsi

Hi Neil,

Thanks for your review comments.

Quoted 12 lines · Neil Armstrong

Hi,

Quoted 8 lines · Anand Moon

Move u-boot specific common nodes in the dts files to meson-g12-common-u-boot.dtsi. This allows us to keep the basic dts[i] files up-to-date with the ones in kernel,
but at the same time allowing the u-boot to add its own properties to the existing nodes.
Also add missing mmc alias to dts nodes to avoid below debug warning.

Quoted 7 lines
Quoted 2 lines

mmc_bind: alias ret=-2, devnum=-1
mmc_bind: alias ret=-2, devnum=-1

Same as patch 4.

Neil

$ git grep meson-g12-common-u-boot.dtsi
arch/arm/dts/meson-g12a-sei510-u-boot.dtsi:#include
"meson-g12-common-u-boot.dtsi"
arch/arm/dts/meson-g12a-u200-u-boot.dtsi:#include "meson-g12-common-u-boot.dtsi"
arch/arm/dts/meson-g12b-odroid-n2-u-boot.dtsi:#include
"meson-g12-common-u-boot.dtsi"
arch/arm/dts/meson-sm1-sei610-u-boot.dtsi:#include
"meson-g12-common-u-boot.dtsi"

So all the common nodes is included in *meson-g12-common-u-boot.dtsi* for G12 dts.

-Anand

Quoted 144 lines
Quoted 144 lines

---
No changes from previous patch

---
 arch/arm/dts/meson-g12-common-u-boot.dtsi | 12 ++++++++++++
 arch/arm/dts/meson-g12a-sei510.dts        |  9 ---------
 arch/arm/dts/meson-g12a-u200.dts          |  9 ---------
 arch/arm/dts/meson-g12b-odroid-n2.dts     |  9 ---------
 arch/arm/dts/meson-khadas-vim3.dtsi       |  9 ---------
 arch/arm/dts/meson-sm1-sei610.dts         |  9 ---------
 6 files changed, 12 insertions(+), 45 deletions(-)
arch/arm/dts/meson-g12-common-u-boot.dtsi +12 -0
index 38fd3d3feb..347b8ded22 100644
@@ -8,6 +8,18 @@
      soc {
              u-boot,dm-pre-reloc;
      };
+
+     aliases {
+             serial0 = &uart_AO;
+             ethernet0 = &ethmac;
+             mmc0 = &sd_emmc_a;
+             mmc1 = &sd_emmc_b;
+             mmc2 = &sd_emmc_c;
+     };
+
+     chosen {
+             stdout-path = "serial0:115200n8";
+     };
 };
 
 &canvas {
arch/arm/dts/meson-g12a-sei510.dts +0 -9
index c7a8736885..c6a48ebbe5 100644
@@ -28,11 +28,6 @@
              };
      };
 
-     aliases {
-             serial0 = &uart_AO;
-             ethernet0 = &ethmac;
-     };
-
      mono_dac: audio-codec-0 {
              compatible = "maxim,max98357a";
              #sound-dai-cells = <0>;
@@ -49,10 +44,6 @@
              sound-name-prefix = "MIC";
      };
 
-     chosen {
-             stdout-path = "serial0:115200n8";
-     };
-
      cvbs-connector {
              compatible = "composite-video-connector";
 
arch/arm/dts/meson-g12a-u200.dts +0 -9
index 8551fbd4a4..8be7b6985b 100644
@@ -13,15 +13,6 @@
      compatible = "amlogic,u200", "amlogic,g12a";
      model = "Amlogic Meson G12A U200 Development Board";
 
-     aliases {
-             serial0 = &uart_AO;
-             ethernet0 = &ethmac;
-     };
-
-     chosen {
-             stdout-path = "serial0:115200n8";
-     };
-
      cvbs-connector {
              compatible = "composite-video-connector";
 
arch/arm/dts/meson-g12b-odroid-n2.dts +0 -9
index 42f1540575..a37f66a5e0 100644
@@ -15,15 +15,6 @@
      compatible = "hardkernel,odroid-n2", "amlogic,g12b";
      model = "Hardkernel ODROID-N2";
 
-     aliases {
-             serial0 = &uart_AO;
-             ethernet0 = &ethmac;
-     };
-
-     chosen {
-             stdout-path = "serial0:115200n8";
-     };
-
      memory at 0 {
              device_type = "memory";
              reg = <0x0 0x0 0x0 0x40000000>;
arch/arm/dts/meson-khadas-vim3.dtsi +0 -9
index 8647da7d66..c6b0ce9a88 100644
@@ -11,15 +11,6 @@
 / {
      model = "Khadas VIM3";
 
-     aliases {
-             serial0 = &uart_AO;
-             ethernet0 = &ethmac;
-     };
-
-     chosen {
-             stdout-path = "serial0:115200n8";
-     };
-
      memory at 0 {
              device_type = "memory";
              reg = <0x0 0x0 0x0 0x80000000>;
arch/arm/dts/meson-sm1-sei610.dts +0 -9
index 3435aaa4e8..4372708811 100644
@@ -14,15 +14,6 @@
      compatible = "seirobotics,sei610", "amlogic,sm1";
      model = "SEI Robotics SEI610";
 
-     aliases {
-             serial0 = &uart_AO;
-             ethernet0 = &ethmac;
-     };
-
-     chosen {
-             stdout-path = "serial0:115200n8";
-     };
-
      emmc_pwrseq: emmc-pwrseq {
              compatible = "mmc-pwrseq-emmc";
              reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
author
#21 lore raw

PATCH v6 5/5 arm: dts: s400: Move common nodes to the -u-boot.dtsi

In reply to Anand Moon

Move u-boot specific common nodes in the dts files to meson-axg-s400-u-boot.dtsi. This allows us to keep the basic dts[i] files up-to-date with the ones in kernel, but at the same time allowing the u-boot to add its own properties to the existing nodes.
Also add missing mmc alias to dts nodes to avoid below debug warning.

mmc_bind: alias ret=-2, devnum=-1
mmc_bind: alias ret=-2, devnum=-1

---
no changes from previous changes

---
 arch/arm/dts/meson-axg-s400-u-boot.dtsi | 16 ++++++++++++++++
 arch/arm/dts/meson-axg-s400.dts         |  9 ---------
 2 files changed, 16 insertions(+), 9 deletions(-)
arch/arm/dts/meson-axg-s400-u-boot.dtsi +16 -0
index c46eb3f38d..74241e9fcd 100644
@@ -2,6 +2,22 @@
 /*
  * Copyright (c) 2017 Amlogic, Inc. All rights reserved.
  */
+/ {
+	soc {
+		u-boot,dm-pre-reloc;
+	};
+
+	aliases {
+		serial0 = &uart_AO;
+		serial1 = &uart_A;
+		mmc1 = &sd_emmc_b;
+		mmc2 = &sd_emmc_c;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
 
 /* wifi module */
 &sd_emmc_b {
arch/arm/dts/meson-axg-s400.dts +0 -9
index 18778ada7b..feb84255ad 100644
@@ -55,11 +55,6 @@
 		};
 	};
 
-	aliases {
-		serial0 = &uart_AO;
-		serial1 = &uart_A;
-	};
-
 	linein: audio-codec at 0 {
 		#sound-dai-cells = <0>;
 		compatible = "everest,es7241";
@@ -100,10 +95,6 @@
 		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
 	};
 
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
 	memory at 0 {
 		device_type = "memory";
 		reg = <0x0 0x0 0x0 0x40000000>;
Signature · 1 line
2.25.0
#22 lore raw

PATCH v6 5/5 arm: dts: s400: Move common nodes to the -u-boot.dtsi

Hi,

Quoted 10 lines · Anand Moon

Move u-boot specific common nodes in the dts files to meson-axg-s400-u-boot.dtsi. This allows us to keep the basic dts[i] files up-to-date with the ones in kernel, but at the same time allowing the u-boot to add its own properties to the existing nodes.
Also add missing mmc alias to dts nodes to avoid below debug warning.

mmc_bind: alias ret=-2, devnum=-1
mmc_bind: alias ret=-2, devnum=-1

Same as patch 4.

Neil

Quoted 64 lines

---
no changes from previous changes

---
 arch/arm/dts/meson-axg-s400-u-boot.dtsi | 16 ++++++++++++++++
 arch/arm/dts/meson-axg-s400.dts         |  9 ---------
 2 files changed, 16 insertions(+), 9 deletions(-)
arch/arm/dts/meson-axg-s400-u-boot.dtsi +16 -0
index c46eb3f38d..74241e9fcd 100644
@@ -2,6 +2,22 @@
 /*
  * Copyright (c) 2017 Amlogic, Inc. All rights reserved.
  */
+/ {
+	soc {
+		u-boot,dm-pre-reloc;
+	};
+
+	aliases {
+		serial0 = &uart_AO;
+		serial1 = &uart_A;
+		mmc1 = &sd_emmc_b;
+		mmc2 = &sd_emmc_c;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
 
 /* wifi module */
 &sd_emmc_b {
arch/arm/dts/meson-axg-s400.dts +0 -9
index 18778ada7b..feb84255ad 100644
@@ -55,11 +55,6 @@
 		};
 	};
 
-	aliases {
-		serial0 = &uart_AO;
-		serial1 = &uart_A;
-	};
-
 	linein: audio-codec at 0 {
 		#sound-dai-cells = <0>;
 		compatible = "everest,es7241";
@@ -100,10 +95,6 @@
 		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
 	};
 
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
 	memory at 0 {
 		device_type = "memory";
 		reg = <0x0 0x0 0x0 0x40000000>;
author
#23 lore raw

PATCH v6 5/5 arm: dts: s400: Move common nodes to the -u-boot.dtsi

hi Neil,

Thanks for your review comments.

Quoted 12 lines · Neil Armstrong

Hi,

Quoted 8 lines · Anand Moon

Move u-boot specific common nodes in the dts files to meson-axg-s400-u-boot.dtsi. This allows us to keep the basic dts[i] files up-to-date with the ones in kernel, but at the same time allowing the u-boot to add its own properties to the existing nodes.
Also add missing mmc alias to dts nodes to avoid below debug warning.

Quoted 8 lines
Quoted 2 lines

mmc_bind: alias ret=-2, devnum=-1
mmc_bind: alias ret=-2, devnum=-1

Same as patch 4.

Neil

$ git grep meson-axg-s400-u-boot.dtsi
it not show any thing, looks like it's not getting included.
so  I will update this in next version.

-Anand

Quoted 64 lines
Quoted 64 lines

---
no changes from previous changes

---
 arch/arm/dts/meson-axg-s400-u-boot.dtsi | 16 ++++++++++++++++
 arch/arm/dts/meson-axg-s400.dts         |  9 ---------
 2 files changed, 16 insertions(+), 9 deletions(-)
arch/arm/dts/meson-axg-s400-u-boot.dtsi +16 -0
index c46eb3f38d..74241e9fcd 100644
@@ -2,6 +2,22 @@
 /*
  * Copyright (c) 2017 Amlogic, Inc. All rights reserved.
  */
+/ {
+     soc {
+             u-boot,dm-pre-reloc;
+     };
+
+     aliases {
+             serial0 = &uart_AO;
+             serial1 = &uart_A;
+             mmc1 = &sd_emmc_b;
+             mmc2 = &sd_emmc_c;
+     };
+
+     chosen {
+             stdout-path = "serial0:115200n8";
+     };
+};
 
 /* wifi module */
 &sd_emmc_b {
arch/arm/dts/meson-axg-s400.dts +0 -9
index 18778ada7b..feb84255ad 100644
@@ -55,11 +55,6 @@
              };
      };
 
-     aliases {
-             serial0 = &uart_AO;
-             serial1 = &uart_A;
-     };
-
      linein: audio-codec at 0 {
              #sound-dai-cells = <0>;
              compatible = "everest,es7241";
@@ -100,10 +95,6 @@
              reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
      };
 
-     chosen {
-             stdout-path = "serial0:115200n8";
-     };
-
      memory at 0 {
              device_type = "memory";
              reg = <0x0 0x0 0x0 0x40000000>;