Skip to contentSkip to conversation

Only one subvolume can be mounted after replace/balance

DISCUSSION Jakob Schöttl 2 participants 4 messages Jan 23, 2021 – Jan 27, 2021 Btrfs file system

lore
Share & tools
lore
#0 lore raw

Hi,

In short:
When mounting a second subvolume from a pool, I get this error:
"mount: /mnt: wrong fs type, bad option, bad superblock on /dev/sda, missing code page or helper program, or other." dmesg | grep BTRFS only shows this error:
info (device sda): disk space caching is enabled
error (device sda): Remounting read-write after error is not allowed

What happened:

In my RAID1 pool with two disk, I successfully replaced one disk with

btrfs replace start 2 /dev/sdx

After that, I mounted the pool and did

btrfs fi show /mnt

which showed WARNINGs about
"filesystems with multiple block group profiles detected" (don't remember exactly)

I thought it is a good idea to do

btrfs balance start /mnt

which finished without errors.

Now, I can only mount one (sub)volume of the pool at a time. Others can only be mounted read-only. See error messages at top of this mail.

Do you have any idea what happened or how to fix it?

I already tried rescue zero-log and super-recovery which was successful but didn't help.

Regards, Jakob

#1 lore raw
Quoted 10 lines · Jakob Schöttl

Hi,

In short:
When mounting a second subvolume from a pool, I get this error:
"mount: /mnt: wrong fs type, bad option, bad superblock on /dev/sda, missing code page or helper program, or other."
dmesg | grep BTRFS only shows this error:
info (device sda): disk space caching is enabled
error (device sda): Remounting read-write after error is not allowed

It went read-only before this because it's confused. You need to unmount it before it can be mounted rw. In some cases a reboot is needed.

Quoted 8 lines

What happened:

In my RAID1 pool with two disk, I successfully replaced one disk with

btrfs replace start 2 /dev/sdx

After that, I mounted the pool and did

I don't understand this sequence. In order to do a replace, the file system is already mounted.

Quoted 7 lines

btrfs fi show /mnt

which showed WARNINGs about
"filesystems with multiple block group profiles detected" (don't remember exactly)

Quoted 5 lines

I thought it is a good idea to do

btrfs balance start /mnt

which finished without errors.

Balance alone does not convert block groups to a new profile. You have to explicitly select a conversion filter, e.g.

btrfs balance start -dconvert=raid1,soft -mconvert=raid1,soft /mnt

Quoted 7 lines

Now, I can only mount one (sub)volume of the pool at a time. Others can only be mounted read-only. See error messages at top of this mail.

Do you have any idea what happened or how to fix it?

I already tried rescue zero-log and super-recovery which was successful but didn't help.

I advise anticipating the confusion will get worse, and take the opportunity to refresh the backups. That's the top priority, not fixing the file system.

Next let us know the following:

kernel version
btrfs-progs version
Output from commands:
btrfs fi us /mnt
btrfs check --readonly

Signature · 1 line
Chris Murphy
#2 lore raw

Thank you Chris, it's resolved now, see below.

Am 25.01.21 um 23:47 schrieb Chris Murphy:

Quoted 10 lines · Jakob Schöttl
Quoted 9 lines

Hi,

In short:
When mounting a second subvolume from a pool, I get this error:
"mount: /mnt: wrong fs type, bad option, bad superblock on /dev/sda, missing code page or helper program, or other."
dmesg | grep BTRFS only shows this error:
info (device sda): disk space caching is enabled
error (device sda): Remounting read-write after error is not allowed

Quoted 3 lines

It went read-only before this because it's confused. You need to unmount it before it can be mounted rw. In some cases a reboot is needed.

Oh, I didn't notice that the pool was already mounted (via fstab).
The filesystem where out of space and I had to resize both disks separately. And I had to mount with -o skip_balance for that. Now it works again.

Quoted 9 lines
Quoted 7 lines

What happened:

In my RAID1 pool with two disk, I successfully replaced one disk with

btrfs replace start 2 /dev/sdx

After that, I mounted the pool and did

I don't understand this sequence. In order to do a replace, the file system is already mounted.

That was, what I did before my actual problem occurred. But it's resolved now.

Quoted 8 lines
Quoted 8 lines

btrfs fi show /mnt

which showed WARNINGs about
"filesystems with multiple block group profiles detected" (don't remember exactly)

I thought it is a good idea to do

Quoted 7 lines
Quoted 3 lines

btrfs balance start /mnt

which finished without errors.

Balance alone does not convert block groups to a new profile. You have to explicitly select a conversion filter, e.g.

btrfs balance start -dconvert=raid1,soft -mconvert=raid1,soft /mnt

I didn't want to convert to a new profile. I thought btrfs replace automatically uses the same profile as the pool?

Regards, Jakob

#3 lore raw
Quoted 44 lines · Jakob Schöttl

Thank you Chris, it's resolved now, see below.

Am 25.01.21 um 23:47 schrieb Chris Murphy:

Quoted 10 lines · Jakob Schöttl
Quoted 9 lines

Hi,

In short:
When mounting a second subvolume from a pool, I get this error:
"mount: /mnt: wrong fs type, bad option, bad superblock on /dev/sda, missing code page or helper program, or other."
dmesg | grep BTRFS only shows this error:
info (device sda): disk space caching is enabled
error (device sda): Remounting read-write after error is not allowed

Quoted 3 lines

It went read-only before this because it's confused. You need to unmount it before it can be mounted rw. In some cases a reboot is needed.

Oh, I didn't notice that the pool was already mounted (via fstab). The filesystem where out of space and I had to resize both disks separately. And I had to mount with -o skip_balance for that. Now it works again.

Quoted 9 lines
Quoted 7 lines

What happened:

In my RAID1 pool with two disk, I successfully replaced one disk with

btrfs replace start 2 /dev/sdx

After that, I mounted the pool and did

I don't understand this sequence. In order to do a replace, the file system is already mounted.

That was, what I did before my actual problem occurred. But it's resolved now.

Quoted 10 lines
Quoted 10 lines

btrfs fi show /mnt

which showed WARNINGs about
"filesystems with multiple block group profiles detected" (don't remember exactly)

I thought it is a good idea to do

btrfs balance start /mnt

Quoted 7 lines
Quoted 5 lines
Quoted 1 line

which finished without errors.

Balance alone does not convert block groups to a new profile. You have to explicitly select a conversion filter, e.g.

btrfs balance start -dconvert=raid1,soft -mconvert=raid1,soft /mnt

I didn't want to convert to a new profile. I thought btrfs replace automatically uses the same profile as the pool?

Btrfs replace does not change the profile. But you reported mixed profile block groups, which means conversion is indicated to make sure they're al the same. Please post:

sudo btrfs fi us /mnt

Let's see what the block groups are and what you want them to be and then see what conversion command might be indicated.

Signature · 1 line
Chris Murphy