Bug: 2.6.32 ath5k, associating with WEP128 AP is unreliable
Hello folks,
I recently tried upgrading to kernel version 2.6.32, but after this upgrade my wireless card became flaky when making connections. In cases where a connection can be established it is stable, but there are problems when making wireless associations. Downgrading to kernel version 2.6.31 resolves this issue. I'm not sure at the moment which versions of the ath5k driver maps to these kernel versions.
Here is a brief description of my system:
Machine: Acer Aspire One D150 Netbook Wireless Card: Atheros AR5001. Full lspci dump is attached as "Atheros_AR5001.txt" Driver: ath5k Kernel Log: Attached as "messages.log" Distro: Arch Linux
I'm currently using netcfg 2.2.1 to establish a wireless connection. Immediately after system boot when it tries to connect, the wireless association fails, and the only message in the system log is:
Jan 24 11:47:04 aao1 kernel: ADDRCONF(NETDEV_UP): wlan0: link is not ready
If I try a second time, the connection succeeds, and is stable. However, if I then terminate the connection I cannot get it back no matter how many times I try. From that point on, it will always report that it fails to get an IP address from the DHCP server.
I'm assuming this issue is related to the ath5k driver itself -- the network I'm using is only WEP128, and doesn't need wpa_supplicant. In fact, I have fewer problems when I connect to WPA+TKIP networks with wpa_supplicant.
Reverting to 2.6.31 resolves this issue. It will connect the first time, and I can disconnect/re-connect several times without issue.
I initially reported on the Arch Linux Flyspray system at:
http://bugs.archlinux.org/task/17992
I was advised to report it upstream.
If there is some additional information I can easily gather for you, please let me know. Unfortunately, right now I am probably not going to have the bandwidth to build a custom kernel or try bleeding edge drivers on this machine, but I at least wanted to do my part to make sure this issue was documented.
Thanks and best regards,
Don
01:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01)
Subsystem: Foxconn International, Inc. Device e008
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at 55100000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit-
Address: 00000000 Data: 0000
Capabilities: [60] Express (v1) Legacy Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM L1 Enabled; RCB 128 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [90] MSI-X: Enable- Count=1 Masked-
Vector table: BAR=0 offset=00000000
PBA: BAR=0 offset=00000000
Capabilities: [100] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr+ BadTLP- BadDLLP- Rollover- Timeout+ NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 14, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [140] Virtual Channel <?>
Kernel driver in use: ath5k
Kernel modules: ath5k
Jan 24 11:46:57 aao1 kernel: Linux version 2.6.32-ARCH (tobias@T-POWA-LX) (gcc version 4.4.2 20091208 (prerelease) (GCC) ) #1 SMP PREEMPT Sat Jan 23 13:53:44 UTC 2010 Jan 24 11:46:57 aao1 kernel: KERNEL supported cpus: Jan 24 11:46:57 aao1 kernel: Intel GenuineIntel Jan 24 11:46:57 aao1 kernel: AMD AuthenticAMD Jan 24 11:46:57 aao1 kernel: NSC Geode by NSC Jan 24 11:46:57 aao1 kernel: Cyrix CyrixInstead Jan 24 11:46:57 aao1 kernel: Centaur CentaurHauls Jan 24 11:46:57 aao1 kernel: Transmeta GenuineTMx86 Jan 24 11:46:57 aao1 kernel: Transmeta TransmetaCPU Jan 24 11:46:57 aao1 kernel: UMC UMC UMC UMC Jan 24 11:46:57 aao1 kernel: BIOS-provided physical RAM map: Jan 24 11:46:57 aao1 kernel: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) Jan 24 11:46:57 aao1 kernel: BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) Jan 24 11:46:57 aao1 kernel: BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) Jan 24 11:46:57 aao1 kernel: BIOS-e820: 0000000000100000 - 000000003f576000 (usable) Jan 24 11:46:57 aao1 kernel: BIOS-e820: 000000003f576000 - 000000003f5bf000 (reserved) Jan 24 11:46:57 aao1 kernel: BIOS-e820: 000000003f5bf000 - 000000003f66d000 (usable) Jan 24 11:46:57 aao1 kernel: BIOS-e820: 000000003f66d000 - 000000003f6bf000 (ACPI NVS) Jan 24 11:46:57 aao1 kernel: BIOS-e820: 000000003f6bf000 - 000000003f6ef000 (usable) Jan 24 11:46:57 aao1 kernel: BIOS-e820: 000000003f6ef000 - 000000003f6ff000 (ACPI data) Jan 24 11:46:57 aao1 kernel: BIOS-e820: 000000003f6ff000 - 000000003f700000 (usable) Jan 24 11:46:57 aao1 kernel: BIOS-e820: 000000003f700000 - 0000000040000000 (reserved) Jan 24 11:46:57 aao1 kernel: BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) Jan 24 11:46:57 aao1 kernel: BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) Jan 24 11:46:57 aao1 kernel: BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved) Jan 24 11:46:57 aao1 kernel: BIOS-e820: 00000000fed1c000 - 00000000fed20000 (reserved) Jan 24 11:46:57 aao1 kernel: BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) Jan 24 11:46:57 aao1 kernel: BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved) Jan 24 11:46:57 aao1 kernel: DMI 2.4 present. Jan 24 11:46:57 aao1 kernel: last_pfn = 0x3f700 max_arch_pfn = 0x100000 Jan 24 11:46:57 aao1 kernel: x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 Jan 24 11:46:57 aao1 kernel: Scanning 1 areas for low memory corruption Jan 24 11:46:57 aao1 kernel: modified physical RAM map: Jan 24 11:46:57 aao1 kernel: modified: 0000000000000000 - 0000000000002000 (usable) Jan 24 11:46:57 aao1 kernel: modified: 0000000000002000 - 0000000000006000 (reserved) Jan 24 11:46:57 aao1 kernel: modified: 0000000000006000 - 000000000009fc00 (usable) Jan 24 11:46:57 aao1 kernel: modified: 000000000009fc00 - 00000000000a0000 (reserved) Jan 24 11:46:57 aao1 kernel: modified: 00000000000e0000 - 0000000000100000 (reserved) Jan 24 11:46:57 aao1 kernel: modified: 0000000000100000 - 000000003f576000 (usable) Jan 24 11:46:57 aao1 kernel: modified: 000000003f576000 - 000000003f5bf000 (reserved) Jan 24 11:46:57 aao1 kernel: modified: 000000003f5bf000 - 000000003f66d000 (usable) Jan 24 11:46:57 aao1 kernel: modified: 000000003f66d000 - 000000003f6bf000 (ACPI NVS) Jan 24 11:46:57 aao1 kernel: modified: 000000003f6bf000 - 000000003f6ef000 (usable) Jan 24 11:46:57 aao1 kernel: modified: 000000003f6ef000 - 000000003f6ff000 (ACPI data) Jan 24 11:46:57 aao1 kernel: modified: 000000003f6ff000 - 000000003f700000 (usable) Jan 24 11:46:57 aao1 kernel: modified: 000000003f700000 - 0000000040000000 (reserved) Jan 24 11:46:57 aao1 kernel: modified: 00000000e0000000 - 00000000f0000000 (reserved) Jan 24 11:46:57 aao1 kernel: modified: 00000000fec00000 - 00000000fec01000 (reserved) Jan 24 11:46:57 aao1 kernel: modified: 00000000fed14000 - 00000000fed1a000 (reserved) Jan 24 11:46:57 aao1 kernel: modified: 00000000fed1c000 - 00000000fed20000 (reserved) Jan 24 11:46:57 aao1 kernel: modified: 00000000fee00000 - 00000000fee01000 (reserved) Jan 24 11:46:57 aao1 kernel: modified: 00000000fff00000 - 0000000100000000 (reserved) Jan 24 11:46:57 aao1 kernel: init_memory_mapping: 0000000000000000-00000000377fe000 Jan 24 11:46:57 aao1 kernel: RAMDISK: 3f4b3000 - 3f565860 Jan 24 11:46:57 aao1 kernel: Allocated new RAMDISK: 00100000 - 001b2860 Jan 24 11:46:57 aao1 kernel: Move RAMDISK from 000000003f4b3000 - 000000003f56585f to 00100000 - 001b285f Jan 24 11:46:57 aao1 kernel: ACPI: RSDP 000fe020 00024 (v02 ACER ) Jan 24 11:46:57 aao1 kernel: ACPI: XSDT 3f6fe120 00064 (v01 ACER ACER 00000001 01000013) Jan 24 11:46:57 aao1 kernel: ACPI: FACP 3f6fc000 000F4 (v04 ACER ACER 00000001 1025 01000013) Jan 24 11:46:57 aao1 kernel: ACPI: DSDT 3f6f1000 06D44 (v01 ACER ACER 00000001 1025 01000013) Jan 24 11:46:57 aao1 kernel: ACPI: FACS 3f688000 00040 Jan 24 11:46:57 aao1 kernel: ACPI: SSDT 3f6fd000 004C4 (v02 PmRef CpuPm 00003000 INTL 20051117) Jan 24 11:46:57 aao1 kernel: ACPI: HPET 3f6fb000 00038 (v01 ACER ACER 00000001 1025 01000013) Jan 24 11:46:57 aao1 kernel: ACPI: APIC 3f6fa000 00068 (v02 ACER ACER 00000001 1025 01000013) Jan 24 11:46:57 aao1 kernel: ACPI: MCFG 3f6f9000 0003C (v01 ACER ACER 00000001 1025 01000013) Jan 24 11:46:57 aao1 kernel: ACPI: ASF! 3f6f8000 000A5 (v32 ACER ACER 00000001 1025 01000013) Jan 24 11:46:57 aao1 kernel: ACPI: SLIC 3f6f0000 00180 (v01 ACER ACER 00000001 1025 01000013) Jan 24 11:46:57 aao1 kernel: ACPI: BOOT 3f6ef000 00028 (v01 ACER ACER 00000001 1025 01000013) Jan 24 11:46:57 aao1 kernel: 127MB HIGHMEM available. Jan 24 11:46:57 aao1 kernel: 887MB LOWMEM available. Jan 24 11:46:57 aao1 kernel: mapped low ram: 0 - 377fe000 Jan 24 11:46:57 aao1 kernel: low ram: 0 - 377fe000 Jan 24 11:46:57 aao1 kernel: node 0 low ram: 00000000 - 377fe000 Jan 24 11:46:57 aao1 kernel: node 0 bootmap 00008000 - 0000ef00 Jan 24 11:46:57 aao1 kernel: (9 early reservations) ==> bootmem [0000000000 - 00377fe000] Jan 24 11:46:57 aao1 kernel: #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000] Jan 24 11:46:57 aao1 kernel: #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000] Jan 24 11:46:57 aao1 kernel: #2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000] Jan 24 11:46:57 aao1 kernel: #3 [0001000000 - 000152c024] TEXT DATA BSS ==> [0001000000 - 000152c024] Jan 24 11:46:57 aao1 kernel: #4 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 0000100000] Jan 24 11:46:57 aao1 kernel: #5 [000152d000 - 0001533148] BRK ==> [000152d000 - 0001533148] Jan 24 11:46:57 aao1 kernel: #6 [0000007000 - 0000008000] PGTABLE ==> [0000007000 - 0000008000] Jan 24 11:46:57 aao1 kernel: #7 [0000100000 - 00001b2860] NEW RAMDISK ==> [0000100000 - 00001b2860] Jan 24 11:46:57 aao1 kernel: #8 [0000008000 - 000000f000] BOOTMAP ==> [0000008000 - 000000f000] Jan 24 11:46:57 aao1 kernel: Zone PFN ranges: Jan 24 11:46:57 aao1 kernel: DMA 0x00000000 -> 0x00001000 Jan 24 11:46:57 aao1 kernel: Normal 0x00001000 -> 0x000377fe Jan 24 11:46:57 aao1 kernel: HighMem 0x000377fe -> 0x0003f700 Jan 24 11:46:57 aao1 kernel: Movable zone start PFN for each node Jan 24 11:46:57 aao1 kernel: early_node_map[6] active PFN ranges Jan 24 11:46:57 aao1 kernel: 0: 0x00000000 -> 0x00000002 Jan 24 11:46:57 aao1 kernel: 0: 0x00000006 -> 0x0000009f Jan 24 11:46:57 aao1 kernel: 0: 0x00000100 -> 0x0003f576 Jan 24 11:46:57 aao1 kernel: 0: 0x0003f5bf -> 0x0003f66d Jan 24 11:46:57 aao1 kernel: 0: 0x0003f6bf -> 0x0003f6ef Jan 24 11:46:57 aao1 kernel: 0: 0x0003f6ff -> 0x0003f700 Jan 24 11:46:57 aao1 kernel: Using APIC driver default Jan 24 11:46:57 aao1 kernel: ACPI: PM-Timer IO Port: 0x408 Jan 24 11:46:57 aao1 kernel: ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Jan 24 11:46:57 aao1 kernel: ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) Jan 24 11:46:57 aao1 kernel: ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) Jan 24 11:46:57 aao1 kernel: ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1]) Jan 24 11:46:57 aao1 kernel: ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0]) Jan 24 11:46:57 aao1 kernel: IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23 Jan 24 11:46:57 aao1 kernel: ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) Jan 24 11:46:57 aao1 kernel: ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) Jan 24 11:46:57 aao1 kernel: Enabling APIC mode: Flat. Using 1 I/O APICs Jan 24 11:46:57 aao1 kernel: Using ACPI (MADT) for SMP configuration information Jan 24 11:46:57 aao1 kernel: ACPI: HPET id: 0x8086a201 base: 0xfed00000 Jan 24 11:46:57 aao1 kernel: SMP: Allowing 2 CPUs, 0 hotplug CPUs Jan 24 11:46:57 aao1 kernel: PM: Registered nosave memory: 0000000000002000 - 0000000000006000 Jan 24 11:46:57 aao1 kernel: PM: Registered nosave memory: 000000000009f000 - 00000000000a0000 Jan 24 11:46:57 aao1 kernel: PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000 Jan 24 11:46:57 aao1 kernel: PM: Registered nosave memory: 00000000000e0000 - 0000000000100000 Jan 24 11:46:57 aao1 kernel: Allocating PCI resources starting at 40000000 (gap: 40000000:a0000000) Jan 24 11:46:57 aao1 kernel: Booting paravirtualized kernel on bare hardware Jan 24 11:46:57 aao1 kernel: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:2 nr_node_ids:1 Jan 24 11:46:57 aao1 kernel: PERCPU: Embedded 14 pages/cpu @c2000000 s34680 r0 d22664 u2097152 Jan 24 11:46:57 aao1 kernel: pcpu-alloc: s34680 r0 d22664 u2097152 alloc=1*4194304 Jan 24 11:46:57 aao1 kernel: pcpu-alloc: [0] 0 1 Jan 24 11:46:57 aao1 kernel: Built 1 zonelists in Zone order, mobility grouping on. Total pages: 257537 Jan 24 11:46:57 aao1 kernel: Kernel command line: root=/dev/disk/by-uuid/0ebc9be7-c650-4257-95b7-a16e7416f9c4 ro snd-hda-intel.model=auto resume=/dev/disk/by-uuid/87f5b659-2ac1-4553-be61-30e3f720372c elevator=deadline vga=789 Jan 24 11:46:57 aao1 kernel: PID hash table entries: 4096 (order: 2, 16384 bytes) Jan 24 11:46:57 aao1 kernel: Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Jan 24 11:46:57 aao1 kernel: Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Jan 24 11:46:57 aao1 kernel: Enabling fast FPU save and restore... done. Jan 24 11:46:57 aao1 kernel: Enabling unmasked SIMD FPU exception support... done. Jan 24 11:46:57 aao1 kernel: Initializing CPU#0 Jan 24 11:46:57 aao1 kernel: Initializing HighMem for node 0 (000377fe:0003f700) Jan 24 11:46:57 aao1 kernel: Memory: 1022660k/1039360k available (2793k kernel code, 15120k reserved, 1180k data, 408k init, 129372k highmem) Jan 24 11:46:57 aao1 kernel: virtual kernel memory layout: Jan 24 11:46:57 aao1 kernel: fixmap : 0xfff1e000 - 0xfffff000 ( 900 kB) Jan 24 11:46:57 aao1 kernel: pkmap : 0xff800000 - 0xffc00000 (4096 kB) Jan 24 11:46:57 aao1 kernel: vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB) Jan 24 11:46:57 aao1 kernel: lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB) Jan 24 11:46:57 aao1 kernel: .init : 0xc13e2000 - 0xc1448000 ( 408 kB) Jan 24 11:46:57 aao1 kernel: .data : 0xc12ba77a - 0xc13e1908 (1180 kB) Jan 24 11:46:57 aao1 kernel: .text : 0xc1000000 - 0xc12ba77a (2793 kB) Jan 24 11:46:57 aao1 kernel: Checking if this processor honours the WP bit even in supervisor mode...Ok. Jan 24 11:46:57 aao1 kernel: SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 Jan 24 11:46:57 aao1 kernel: Hierarchical RCU implementation. Jan 24 11:46:57 aao1 kernel: NR_IRQS:512 Jan 24 11:46:57 aao1 kernel: Console: colour dummy device 80x25 Jan 24 11:46:57 aao1 kernel: console [tty0] enabled Jan 24 11:46:57 aao1 kernel: HPET: 3 timers in total, 0 timers will be used for per-cpu timer Jan 24 11:46:57 aao1 kernel: Fast TSC calibration failed Jan 24 11:46:57 aao1 kernel: TSC: PIT calibration matches HPET. 1 loops Jan 24 11:46:57 aao1 kernel: Detected 1595.955 MHz processor. Jan 24 11:46:57 aao1 kernel: Calibrating delay loop (skipped), value calculated using timer frequency.. 3193.90 BogoMIPS (lpj=5319850) Jan 24 11:46:57 aao1 kernel: Security Framework initialized Jan 24 11:46:57 aao1 kernel: Mount-cache hash table entries: 512 Jan 24 11:46:57 aao1 kernel: CPU: L1 I cache: 32K, L1 D cache: 24K Jan 24 11:46:57 aao1 kernel: CPU: L2 cache: 512K Jan 24 11:46:57 aao1 kernel: CPU: Physical Processor ID: 0 Jan 24 11:46:57 aao1 kernel: CPU: Processor Core ID: 0 Jan 24 11:46:57 aao1 kernel: mce: CPU supports 5 MCE banks Jan 24 11:46:57 aao1 kernel: CPU0: Thermal monitoring enabled (TM2) Jan 24 11:46:57 aao1 kernel: using mwait in idle threads. Jan 24 11:46:57 aao1 kernel: Performance Events: Atom events, Intel PMU driver. Jan 24 11:46:57 aao1 kernel: ... version: 3 Jan 24 11:46:57 aao1 kernel: ... bit width: 40 Jan 24 11:46:57 aao1 kernel: ... generic registers: 2 Jan 24 11:46:57 aao1 kernel: ... value mask: 000000ffffffffff Jan 24 11:46:57 aao1 kernel: ... max period: 000000007fffffff Jan 24 11:46:57 aao1 kernel: ... fixed-purpose events: 3 Jan 24 11:46:57 aao1 kernel: ... event mask: 0000000700000003 Jan 24 11:46:57 aao1 kernel: Checking 'hlt' instruction... OK. Jan 24 11:46:57 aao1 kernel: ACPI: Core revision 20090903 Jan 24 11:46:57 aao1 kernel: ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 Jan 24 11:46:57 aao1 kernel: CPU0: Intel(R) Atom(TM) CPU N270 @ 1.60GHz stepping 02 Jan 24 11:46:57 aao1 kernel: Booting processor 1 APIC 0x1 ip 0x6000 Jan 24 11:46:57 aao1 kernel: Initializing CPU#1 Jan 24 11:46:57 aao1 kernel: Calibrating delay using timer specific routine.. 3193.98 BogoMIPS (lpj=5319968) Jan 24 11:46:57 aao1 kernel: CPU: L1 I cache: 32K, L1 D cache: 24K Jan 24 11:46:57 aao1 kernel: CPU: L2 cache: 512K Jan 24 11:46:57 aao1 kernel: CPU: Physical Processor ID: 0 Jan 24 11:46:57 aao1 kernel: CPU: Processor Core ID: 0 Jan 24 11:46:57 aao1 kernel: CPU1: Thermal monitoring enabled (TM2) Jan 24 11:46:57 aao1 kernel: CPU1: Intel(R) Atom(TM) CPU N270 @ 1.60GHz stepping 02 Jan 24 11:46:57 aao1 kernel: checking TSC synchronization [CPU#0 -> CPU#1]: passed. Jan 24 11:46:57 aao1 kernel: Brought up 2 CPUs Jan 24 11:46:57 aao1 kernel: Total of 2 processors activated (6386.88 BogoMIPS). Jan 24 11:46:57 aao1 kernel: NET: Registered protocol family 16 Jan 24 11:46:57 aao1 kernel: ACPI: bus type pci registered Jan 24 11:46:57 aao1 kernel: PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255 Jan 24 11:46:57 aao1 kernel: PCI: MCFG area at e0000000 reserved in E820 Jan 24 11:46:57 aao1 kernel: PCI: Using MMCONFIG for extended config space Jan 24 11:46:57 aao1 kernel: PCI: Using configuration type 1 for base access Jan 24 11:46:57 aao1 kernel: bio: create slab <bio-0> at 0 Jan 24 11:46:57 aao1 kernel: ACPI: Executed 1 blocks of module-level executable AML code Jan 24 11:46:57 aao1 kernel: ACPI: BIOS _OSI(Linux) query ignored Jan 24 11:46:57 aao1 kernel: ACPI: BIOS _OSI(Linux) query ignored Jan 24 11:46:57 aao1 kernel: ACPI: Interpreter enabled Jan 24 11:46:57 aao1 kernel: ACPI: (supports S0 S3 S4 S5) Jan 24 11:46:57 aao1 kernel: ACPI: Using IOAPIC for interrupt routing Jan 24 11:46:57 aao1 kernel: [Firmware Bug]: ACPI: ACPI brightness control misses _BQC function Jan 24 11:46:57 aao1 kernel: ACPI: EC: GPE = 0x19, I/O: command/status = 0x66, data = 0x62 Jan 24 11:46:57 aao1 kernel: ACPI: Power Resource [FN00] (on) Jan 24 11:46:57 aao1 kernel: ACPI: No dock devices found. Jan 24 11:46:57 aao1 kernel: ACPI Error (dsfield-0143): [CAPB] Namespace lookup failure, AE_ALREADY_EXISTS Jan 24 11:46:57 aao1 kernel: ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0._OSC] (Node f7016a38), AE_ALREADY_EXISTS Jan 24 11:46:57 aao1 kernel: ACPI: Marking method _OSC as Serialized because of AE_ALREADY_EXISTS error Jan 24 11:46:57 aao1 kernel: ACPI: PCI Root Bridge [PCI0] (0000:00) Jan 24 11:46:57 aao1 kernel: pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold Jan 24 11:46:57 aao1 kernel: pci 0000:00:1b.0: PME# disabled Jan 24 11:46:57 aao1 kernel: pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold Jan 24 11:46:57 aao1 kernel: pci 0000:00:1c.0: PME# disabled Jan 24 11:46:57 aao1 kernel: pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold Jan 24 11:46:57 aao1 kernel: pci 0000:00:1c.1: PME# disabled Jan 24 11:46:57 aao1 kernel: pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold Jan 24 11:46:57 aao1 kernel: pci 0000:00:1c.2: PME# disabled Jan 24 11:46:57 aao1 kernel: pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold Jan 24 11:46:57 aao1 kernel: pci 0000:00:1d.7: PME# disabled Jan 24 11:46:57 aao1 kernel: pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO Jan 24 11:46:57 aao1 kernel: pci 0000:00:1f.0: quirk: region 0500-053f claimed by ICH6 GPIO Jan 24 11:46:57 aao1 kernel: pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at ff2c (mask 0003) Jan 24 11:46:57 aao1 kernel: pci 0000:00:1f.0: ICH7 LPC Generic IO decode 3 PIO at 0068 (mask 0007) Jan 24 11:46:57 aao1 kernel: pci 0000:00:1f.2: PME# supported from D3hot Jan 24 11:46:57 aao1 kernel: pci 0000:00:1f.2: PME# disabled Jan 24 11:46:57 aao1 kernel: pci 0000:03:00.0: PME# supported from D3hot D3cold Jan 24 11:46:57 aao1 kernel: pci 0000:03:00.0: PME# disabled Jan 24 11:46:57 aao1 kernel: pci 0000:00:1e.0: transparent bridge Jan 24 11:46:57 aao1 kernel: ACPI Error (dsfield-0143): [CAPB] Namespace lookup failure, AE_ALREADY_EXISTS Jan 24 11:46:57 aao1 kernel: ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0._OSC] (Node f7016a38), AE_ALREADY_EXISTS Jan 24 11:46:57 aao1 kernel: ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11 12) Jan 24 11:46:57 aao1 kernel: ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 *11 12) Jan 24 11:46:57 aao1 kernel: ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12) Jan 24 11:46:57 aao1 kernel: ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12) Jan 24 11:46:57 aao1 kernel: ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11 12) *0, disabled. Jan 24 11:46:57 aao1 kernel: ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12) *0, disabled. Jan 24 11:46:57 aao1 kernel: ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 10 11 12) *0, disabled. Jan 24 11:46:57 aao1 kernel: ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 10 11 12) *0, disabled. Jan 24 11:46:57 aao1 kernel: vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none Jan 24 11:46:57 aao1 kernel: vgaarb: loaded Jan 24 11:46:57 aao1 kernel: PCI: Using ACPI for IRQ routing Jan 24 11:46:57 aao1 kernel: NetLabel: Initializing Jan 24 11:46:57 aao1 kernel: NetLabel: domain hash size = 128 Jan 24 11:46:57 aao1 kernel: NetLabel: protocols = UNLABELED CIPSOv4 Jan 24 11:46:57 aao1 kernel: NetLabel: unlabeled traffic allowed by default Jan 24 11:46:57 aao1 kernel: Switching to clocksource tsc Jan 24 11:46:57 aao1 kernel: pnp: PnP ACPI init Jan 24 11:46:57 aao1 kernel: ACPI: bus type pnp registered Jan 24 11:46:57 aao1 kernel: pnp 00:01: io resource (0x164e-0x164f) overlaps 0000:00:1c.2 BAR 13 (0x1000-0x2fff), disabling Jan 24 11:46:57 aao1 kernel: pnp: PnP ACPI: found 9 devices Jan 24 11:46:57 aao1 kernel: ACPI: ACPI bus type pnp unregistered Jan 24 11:46:57 aao1 kernel: system 00:01: ioport range 0x200-0x20f has been reserved Jan 24 11:46:57 aao1 kernel: system 00:01: ioport range 0x600-0x60f has been reserved Jan 24 11:46:57 aao1 kernel: system 00:01: ioport range 0x610-0x610 has been reserved Jan 24 11:46:57 aao1 kernel: system 00:01: ioport range 0x800-0x80f has been reserved Jan 24 11:46:57 aao1 kernel: system 00:01: ioport range 0x400-0x47f has been reserved Jan 24 11:46:57 aao1 kernel: system 00:01: ioport range 0x500-0x53f has been reserved Jan 24 11:46:57 aao1 kernel: system 00:01: ioport range 0xff2c-0xff2f has been reserved Jan 24 11:46:57 aao1 kernel: system 00:01: iomem range 0xe0000000-0xefffffff has been reserved Jan 24 11:46:57 aao1 kernel: system 00:01: iomem range 0xfed1c000-0xfed1ffff has been reserved Jan 24 11:46:57 aao1 kernel: system 00:01: iomem range 0xfed14000-0xfed17fff has been reserved Jan 24 11:46:57 aao1 kernel: system 00:01: iomem range 0xfed18000-0xfed18fff has been reserved Jan 24 11:46:57 aao1 kernel: system 00:01: iomem range 0xfed19000-0xfed19fff has been reserved Jan 24 11:46:57 aao1 kernel: system 00:01: iomem range 0xfec00000-0xfec00fff could not be reserved Jan 24 11:46:57 aao1 kernel: system 00:01: iomem range 0xfee00000-0xfee00fff has been reserved Jan 24 11:46:57 aao1 kernel: pci 0000:00:1c.0: PCI bridge, secondary bus 0000:01 Jan 24 11:46:57 aao1 kernel: pci 0000:00:1c.0: IO window: 0x4000-0x4fff Jan 24 11:46:57 aao1 kernel: pci 0000:00:1c.0: MEM window: 0x55100000-0x561fffff Jan 24 11:46:57 aao1 kernel: pci 0000:00:1c.0: PREFETCH window: 0x00000050000000-0x00000050ffffff Jan 24 11:46:57 aao1 kernel: pci 0000:00:1c.1: PCI bridge, secondary bus 0000:02 Jan 24 11:46:57 aao1 kernel: pci 0000:00:1c.1: IO window: 0x3000-0x3fff Jan 24 11:46:57 aao1 kernel: pci 0000:00:1c.1: MEM window: 0x54100000-0x550fffff Jan 24 11:46:57 aao1 kernel: pci 0000:00:1c.1: PREFETCH window: 0x00000051000000-0x00000051ffffff Jan 24 11:46:57 aao1 kernel: pci 0000:00:1c.2: PCI bridge, secondary bus 0000:03 Jan 24 11:46:57 aao1 kernel: pci 0000:00:1c.2: IO window: 0x1000-0x2fff Jan 24 11:46:57 aao1 kernel: pci 0000:00:1c.2: MEM window: 0x53000000-0x540fffff Jan 24 11:46:57 aao1 kernel: pci 0000:00:1c.2: PREFETCH window: 0x00000052000000-0x00000052ffffff Jan 24 11:46:57 aao1 kernel: pci 0000:00:1e.0: PCI bridge, secondary bus 0000:04 Jan 24 11:46:57 aao1 kernel: pci 0000:00:1e.0: IO window: disabled Jan 24 11:46:57 aao1 kernel: pci 0000:00:1e.0: MEM window: disabled Jan 24 11:46:57 aao1 kernel: pci 0000:00:1e.0: PREFETCH window: disabled Jan 24 11:46:57 aao1 kernel: pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 Jan 24 11:46:57 aao1 kernel: pci 0000:00:1c.1: enabling device (0000 -> 0003) Jan 24 11:46:57 aao1 kernel: pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 Jan 24 11:46:57 aao1 kernel: pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 Jan 24 11:46:57 aao1 kernel: NET: Registered protocol family 2 Jan 24 11:46:57 aao1 kernel: IP route cache hash table entries: 32768 (order: 5, 131072 bytes) Jan 24 11:46:57 aao1 kernel: TCP established hash table entries: 131072 (order: 8, 1048576 bytes) Jan 24 11:46:57 aao1 kernel: TCP bind hash table entries: 65536 (order: 7, 524288 bytes) Jan 24 11:46:57 aao1 kernel: TCP: Hash tables configured (established 131072 bind 65536) Jan 24 11:46:57 aao1 kernel: TCP reno registered Jan 24 11:46:57 aao1 kernel: NET: Registered protocol family 1 Jan 24 11:46:57 aao1 kernel: Unpacking initramfs... Jan 24 11:46:57 aao1 kernel: Freeing initrd memory: 714k freed Jan 24 11:46:57 aao1 kernel: Simple Boot Flag value 0x5 read from CMOS RAM was invalid Jan 24 11:46:57 aao1 kernel: Simple Boot Flag at 0x44 set to 0x1 Jan 24 11:46:57 aao1 kernel: apm: BIOS not found. Jan 24 11:46:57 aao1 kernel: Scanning for low memory corruption every 60 seconds Jan 24 11:46:57 aao1 kernel: audit: initializing netlink socket (disabled) Jan 24 11:46:57 aao1 kernel: type=2000 audit(1264355199.513:1): initialized Jan 24 11:46:57 aao1 kernel: highmem bounce pool size: 64 pages Jan 24 11:46:57 aao1 kernel: VFS: Disk quotas dquot_6.5.2 Jan 24 11:46:57 aao1 kernel: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Jan 24 11:46:57 aao1 kernel: msgmni has been set to 1747 Jan 24 11:46:57 aao1 kernel: alg: No test for stdrng (krng) Jan 24 11:46:57 aao1 kernel: Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) Jan 24 11:46:57 aao1 kernel: io scheduler noop registered Jan 24 11:46:57 aao1 kernel: io scheduler anticipatory registered Jan 24 11:46:57 aao1 kernel: io scheduler deadline registered (default) Jan 24 11:46:57 aao1 kernel: io scheduler cfq registered Jan 24 11:46:57 aao1 kernel: vesafb: framebuffer at 0x40000000, mapped to 0xf8080000, using 3750k, total 7872k Jan 24 11:46:57 aao1 kernel: vesafb: mode is 800x600x32, linelength=3200, pages=3 Jan 24 11:46:57 aao1 kernel: vesafb: scrolling: redraw Jan 24 11:46:57 aao1 kernel: vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0 Jan 24 11:46:57 aao1 kernel: Console: switching to colour frame buffer device 100x37 Jan 24 11:46:57 aao1 kernel: fb0: VESA VGA frame buffer device Jan 24 11:46:57 aao1 kernel: isapnp: Scanning for PnP cards... Jan 24 11:46:57 aao1 kernel: isapnp: No Plug & Play device found Jan 24 11:46:57 aao1 kernel: Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled Jan 24 11:46:57 aao1 kernel: input: Macintosh mouse button emulation as /devices/virtual/input/input0 Jan 24 11:46:57 aao1 kernel: PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSS0] at 0x60,0x64 irq 1,12 Jan 24 11:46:57 aao1 kernel: serio: i8042 KBD port at 0x60,0x64 irq 1 Jan 24 11:46:57 aao1 kernel: serio: i8042 AUX port at 0x60,0x64 irq 12 Jan 24 11:46:57 aao1 kernel: mice: PS/2 mouse device common for all mice Jan 24 11:46:57 aao1 kernel: cpuidle: using governor ladder Jan 24 11:46:57 aao1 kernel: cpuidle: using governor menu Jan 24 11:46:57 aao1 kernel: TCP cubic registered Jan 24 11:46:57 aao1 kernel: NET: Registered protocol family 17 Jan 24 11:46:57 aao1 kernel: Using IPI No-Shortcut mode Jan 24 11:46:57 aao1 kernel: input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1 Jan 24 11:46:57 aao1 kernel: registered taskstats version 1 Jan 24 11:46:57 aao1 kernel: Initalizing network drop monitor service Jan 24 11:46:57 aao1 kernel: Freeing unused kernel memory: 408k freed Jan 24 11:46:57 aao1 kernel: SCSI subsystem initialized Jan 24 11:46:57 aao1 kernel: pata_acpi 0000:00:1f.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16 Jan 24 11:46:57 aao1 kernel: pata_acpi 0000:00:1f.1: PCI INT A disabled Jan 24 11:46:57 aao1 kernel: ata_piix 0000:00:1f.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16 Jan 24 11:46:57 aao1 kernel: scsi0 : ata_piix Jan 24 11:46:57 aao1 kernel: scsi1 : ata_piix Jan 24 11:46:57 aao1 kernel: ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x50c0 irq 14 Jan 24 11:46:57 aao1 kernel: ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x50c8 irq 15 Jan 24 11:46:57 aao1 kernel: ahci 0000:00:1f.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17 Jan 24 11:46:57 aao1 kernel: ahci: SSS flag set, parallel bus scan disabled Jan 24 11:46:57 aao1 kernel: ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 1.5 Gbps 0x5 impl SATA mode Jan 24 11:46:57 aao1 kernel: ahci 0000:00:1f.2: flags: 64bit ncq ilck stag pm led clo pio slum part Jan 24 11:46:57 aao1 kernel: scsi2 : ahci Jan 24 11:46:57 aao1 kernel: scsi3 : ahci Jan 24 11:46:57 aao1 kernel: scsi4 : ahci Jan 24 11:46:57 aao1 kernel: scsi5 : ahci Jan 24 11:46:57 aao1 kernel: ata3: SATA max UDMA/133 abar m1024@0x56344000 port 0x56344100 irq 27 Jan 24 11:46:57 aao1 kernel: ata4: DUMMY Jan 24 11:46:57 aao1 kernel: ata5: SATA max UDMA/133 abar m1024@0x56344000 port 0x56344200 irq 27 Jan 24 11:46:57 aao1 kernel: ata6: DUMMY Jan 24 11:46:57 aao1 kernel: ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300) Jan 24 11:46:57 aao1 kernel: ata3.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out Jan 24 11:46:57 aao1 kernel: ata3.00: ATA-8: Hitachi HTS543216L9A300, FB2OC40C, max UDMA/133 Jan 24 11:46:57 aao1 kernel: ata3.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 31/32), AA Jan 24 11:46:57 aao1 kernel: ata3.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04) Jan 24 11:46:57 aao1 kernel: ata3.00: configured for UDMA/133 Jan 24 11:46:57 aao1 kernel: scsi 2:0:0:0: Direct-Access ATA Hitachi HTS54321 FB2O PQ: 0 ANSI: 5 Jan 24 11:46:57 aao1 kernel: ata5: SATA link down (SStatus 0 SControl 300) Jan 24 11:46:57 aao1 kernel: sd 2:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB) Jan 24 11:46:57 aao1 kernel: sd 2:0:0:0: [sda] Write Protect is off Jan 24 11:46:57 aao1 kernel: sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Jan 24 11:46:57 aao1 kernel: sda: sda1 sda2 sda3 sda4 Jan 24 11:46:57 aao1 kernel: sd 2:0:0:0: [sda] Attached SCSI disk Jan 24 11:46:57 aao1 kernel: PM: Starting manual resume from disk Jan 24 11:46:57 aao1 kernel: EXT4-fs (sda3): mounted filesystem with ordered data mode Jan 24 11:46:57 aao1 kernel: rtc_cmos 00:03: RTC can wake from S4 Jan 24 11:46:57 aao1 kernel: rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0 Jan 24 11:46:57 aao1 kernel: rtc0: alarms up to one month, 242 bytes nvram, hpet irqs Jan 24 11:46:57 aao1 kernel: udev: starting version 146 Jan 24 11:46:57 aao1 kernel: ACPI: AC Adapter [AC] (on-line) Jan 24 11:46:57 aao1 kernel: intel_rng: FWH not detected Jan 24 11:46:57 aao1 kernel: usbcore: registered new interface driver usbfs Jan 24 11:46:57 aao1 kernel: usbcore: registered new interface driver hub Jan 24 11:46:57 aao1 kernel: usbcore: registered new device driver usb Jan 24 11:46:57 aao1 kernel: ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver Jan 24 11:46:57 aao1 kernel: ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 16 (level, low) -> IRQ 16 Jan 24 11:46:57 aao1 kernel: ehci_hcd 0000:00:1d.7: EHCI Host Controller Jan 24 11:46:57 aao1 kernel: ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 Jan 24 11:46:57 aao1 kernel: ehci_hcd 0000:00:1d.7: using broken periodic workaround Jan 24 11:46:57 aao1 kernel: ehci_hcd 0000:00:1d.7: debug port 1 Jan 24 11:46:57 aao1 kernel: ehci_hcd 0000:00:1d.7: irq 16, io mem 0x56344400 Jan 24 11:46:57 aao1 kernel: uhci_hcd: USB Universal Host Controller Interface driver Jan 24 11:46:57 aao1 kernel: ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 Jan 24 11:46:57 aao1 kernel: usb usb1: configuration #1 chosen from 1 choice Jan 24 11:46:57 aao1 kernel: hub 1-0:1.0: USB hub found Jan 24 11:46:57 aao1 kernel: hub 1-0:1.0: 8 ports detected Jan 24 11:46:57 aao1 kernel: uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 Jan 24 11:46:57 aao1 kernel: uhci_hcd 0000:00:1d.0: UHCI Host Controller Jan 24 11:46:57 aao1 kernel: uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 Jan 24 11:46:57 aao1 kernel: uhci_hcd 0000:00:1d.0: irq 16, io base 0x000050a0 Jan 24 11:46:57 aao1 kernel: usb usb2: configuration #1 chosen from 1 choice Jan 24 11:46:57 aao1 kernel: hub 2-0:1.0: USB hub found Jan 24 11:46:57 aao1 kernel: hub 2-0:1.0: 2 ports detected Jan 24 11:46:57 aao1 kernel: uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 Jan 24 11:46:57 aao1 kernel: uhci_hcd 0000:00:1d.1: UHCI Host Controller Jan 24 11:46:57 aao1 kernel: uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 Jan 24 11:46:57 aao1 kernel: uhci_hcd 0000:00:1d.1: irq 17, io base 0x00005080 Jan 24 11:46:57 aao1 kernel: usb usb3: configuration #1 chosen from 1 choice Jan 24 11:46:57 aao1 kernel: hub 3-0:1.0: USB hub found Jan 24 11:46:57 aao1 kernel: hub 3-0:1.0: 2 ports detected Jan 24 11:46:57 aao1 kernel: uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 Jan 24 11:46:57 aao1 kernel: uhci_hcd 0000:00:1d.2: UHCI Host Controller Jan 24 11:46:57 aao1 kernel: uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 Jan 24 11:46:57 aao1 kernel: uhci_hcd 0000:00:1d.2: irq 18, io base 0x00005060 Jan 24 11:46:57 aao1 kernel: usb usb4: configuration #1 chosen from 1 choice Jan 24 11:46:57 aao1 kernel: hub 4-0:1.0: USB hub found Jan 24 11:46:57 aao1 kernel: hub 4-0:1.0: 2 ports detected Jan 24 11:46:57 aao1 kernel: uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19 Jan 24 11:46:57 aao1 kernel: uhci_hcd 0000:00:1d.3: UHCI Host Controller Jan 24 11:46:57 aao1 kernel: uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5 Jan 24 11:46:57 aao1 kernel: uhci_hcd 0000:00:1d.3: irq 19, io base 0x00005040 Jan 24 11:46:57 aao1 kernel: usb usb5: configuration #1 chosen from 1 choice Jan 24 11:46:57 aao1 kernel: hub 5-0:1.0: USB hub found Jan 24 11:46:57 aao1 kernel: hub 5-0:1.0: 2 ports detected Jan 24 11:46:57 aao1 kernel: Linux agpgart interface v0.103 Jan 24 11:46:57 aao1 kernel: ACPI: WMI: Mapper loaded Jan 24 11:46:57 aao1 kernel: ATL1E 0000:03:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 Jan 24 11:46:57 aao1 kernel: ACPI: Battery Slot [BAT0] (battery present) Jan 24 11:46:57 aao1 kernel: i801_smbus 0000:00:1f.3: PCI INT B -> GSI 17 (level, low) -> IRQ 17 Jan 24 11:46:57 aao1 kernel: agpgart-intel 0000:00:00.0: Intel 945GME Chipset Jan 24 11:46:57 aao1 kernel: agpgart-intel 0000:00:00.0: detected 7932K stolen memory Jan 24 11:46:57 aao1 kernel: usb 1-2: new high speed USB device using ehci_hcd and address 2 Jan 24 11:46:57 aao1 kernel: agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0x40000000 Jan 24 11:46:57 aao1 kernel: iTCO_vendor_support: vendor-support=0 Jan 24 11:46:57 aao1 kernel: acer-wmi: Acer Laptop ACPI-WMI Extras Jan 24 11:46:57 aao1 kernel: iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05 Jan 24 11:46:57 aao1 kernel: iTCO_wdt: Found a ICH7-M or ICH7-U TCO device (Version=2, TCOBASE=0x0460) Jan 24 11:46:57 aao1 kernel: iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) Jan 24 11:46:57 aao1 kernel: sd 2:0:0:0: Attached scsi generic sg0 type 0 Jan 24 11:46:57 aao1 kernel: input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input2 Jan 24 11:46:57 aao1 kernel: ACPI: Power Button [PWRB] Jan 24 11:46:57 aao1 kernel: input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input3 Jan 24 11:46:57 aao1 kernel: ACPI: Lid Switch [LID0] Jan 24 11:46:57 aao1 kernel: input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input4 Jan 24 11:46:57 aao1 kernel: ACPI: Sleep Button [SLPB] Jan 24 11:46:57 aao1 kernel: input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input5 Jan 24 11:46:57 aao1 kernel: ACPI: Power Button [PWRF] Jan 24 11:46:57 aao1 kernel: usb 1-2: configuration #1 chosen from 1 choice Jan 24 11:46:57 aao1 kernel: fan PNP0C0B:00: registered as cooling_device0 Jan 24 11:46:57 aao1 kernel: ACPI: Fan [FAN] (on) Jan 24 11:46:57 aao1 kernel: cfg80211: Calling CRDA to update world regulatory domain Jan 24 11:46:57 aao1 kernel: thermal LNXTHERM:01: registered as thermal_zone0 Jan 24 11:46:57 aao1 kernel: ACPI: Thermal Zone [THRM] (27 C) Jan 24 11:46:57 aao1 kernel: ACPI: SSDT 3f580c90 00239 (v02 PmRef Cpu0Ist 00003000 INTL 20051117) Jan 24 11:46:57 aao1 kernel: ACPI: SSDT 3f57fe10 001C7 (v02 PmRef Cpu0Cst 00003001 INTL 20051117) Jan 24 11:46:57 aao1 kernel: Marking TSC unstable due to TSC halts in idle Jan 24 11:46:57 aao1 kernel: processor LNXCPU:00: registered as cooling_device1 Jan 24 11:46:57 aao1 kernel: ACPI: SSDT 3f580f10 000D0 (v02 PmRef Cpu1Ist 00003000 INTL 20051117) Jan 24 11:46:57 aao1 kernel: ACPI: SSDT 3f57ef10 00083 (v02 PmRef Cpu1Cst 00003000 INTL 20051117) Jan 24 11:46:57 aao1 kernel: processor LNXCPU:01: registered as cooling_device2 Jan 24 11:46:57 aao1 kernel: Switching to clocksource hpet Jan 24 11:46:57 aao1 kernel: [Firmware Bug]: ACPI: ACPI brightness control misses _BQC function Jan 24 11:46:57 aao1 kernel: acpi device:18: registered as cooling_device3 Jan 24 11:46:57 aao1 kernel: input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input6 Jan 24 11:46:57 aao1 kernel: ACPI: Video Device [OVGA] (multi-head: yes rom: yes post: no) Jan 24 11:46:57 aao1 kernel: ath5k 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 Jan 24 11:46:57 aao1 kernel: ath5k 0000:01:00.0: registered as 'phy0' Jan 24 11:46:57 aao1 kernel: [drm] Initialized drm 1.1.0 20060810 Jan 24 11:46:57 aao1 kernel: Linux video capture interface: v2.00 Jan 24 11:46:57 aao1 kernel: Synaptics Touchpad, model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04771/0xa40000 Jan 24 11:46:57 aao1 kernel: uvcvideo: Found UVC 1.00 device USB 2.0 Camera (0c45:62c0) Jan 24 11:46:57 aao1 kernel: input: USB 2.0 Camera as /devices/pci0000:00/0000:00:1d.7/usb1/1-2/1-2:1.0/input/input7 Jan 24 11:46:57 aao1 kernel: usbcore: registered new interface driver uvcvideo Jan 24 11:46:57 aao1 kernel: USB Video Class driver (v0.1.0) Jan 24 11:46:57 aao1 kernel: input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input8 Jan 24 11:46:57 aao1 kernel: i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 Jan 24 11:46:57 aao1 kernel: [drm] set up 7M of stolen space Jan 24 11:46:57 aao1 kernel: pci_hotplug: PCI Hot Plug PCI Core version: 0.5 Jan 24 11:46:57 aao1 kernel: Registered led device: ath5k-phy0::rx Jan 24 11:46:57 aao1 kernel: Registered led device: ath5k-phy0::tx Jan 24 11:46:57 aao1 kernel: ath5k phy0: Atheros AR2425 chip found (MAC: 0xe2, PHY: 0x70) Jan 24 11:46:57 aao1 kernel: Console: switching to colour dummy device 80x25 Jan 24 11:46:57 aao1 kernel: Console: switching to colour frame buffer device 128x37 Jan 24 11:46:57 aao1 kernel: [drm] LVDS-8: set mode 1024x600 e Jan 24 11:46:57 aao1 kernel: fb0: inteldrmfb frame buffer device Jan 24 11:46:57 aao1 kernel: registered panic notifier Jan 24 11:46:57 aao1 kernel: [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0 Jan 24 11:46:57 aao1 kernel: HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 Jan 24 11:46:57 aao1 kernel: input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input9 Jan 24 11:46:57 aao1 kernel: shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 Jan 24 11:46:57 aao1 kernel: st: Version 20081215, fixed bufsize 32768, s/g segs 256 Jan 24 11:46:57 aao1 kernel: ACPI Error (dsfield-0143): [CAPB] Namespace lookup failure, AE_ALREADY_EXISTS Jan 24 11:46:57 aao1 kernel: ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0._OSC] (Node f7016a38), AE_ALREADY_EXISTS Jan 24 11:46:57 aao1 kernel: ACPI Error (dsfield-0143): [CAPB] Namespace lookup failure, AE_ALREADY_EXISTS Jan 24 11:46:57 aao1 kernel: ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0._OSC] (Node f7016a38), AE_ALREADY_EXISTS Jan 24 11:46:57 aao1 kernel: ACPI Error (dsfield-0143): [CAPB] Namespace lookup failure, AE_ALREADY_EXISTS Jan 24 11:46:57 aao1 kernel: ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0._OSC] (Node f7016a38), AE_ALREADY_EXISTS Jan 24 11:46:57 aao1 kernel: ACPI Error (dsfield-0143): [CAPB] Namespace lookup failure, AE_ALREADY_EXISTS Jan 24 11:46:57 aao1 kernel: ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0._OSC] (Node f7016a38), AE_ALREADY_EXISTS Jan 24 11:46:57 aao1 kernel: ACPI Error (dsfield-0143): [CAPB] Namespace lookup failure, AE_ALREADY_EXISTS Jan 24 11:46:57 aao1 kernel: ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0._OSC] (Node f7016a38), AE_ALREADY_EXISTS Jan 24 11:46:57 aao1 kernel: ACPI Error (dsfield-0143): [CAPB] Namespace lookup failure, AE_ALREADY_EXISTS Jan 24 11:46:57 aao1 kernel: ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0._OSC] (Node f7016a38), AE_ALREADY_EXISTS Jan 24 11:46:57 aao1 kernel: pciehp: PCI Express Hot Plug Controller Driver version: 0.4 Jan 24 11:46:57 aao1 kernel: fuse init (API version 7.13) Jan 24 11:46:57 aao1 kernel: scsi6 : vhba Jan 24 11:46:57 aao1 kernel: input: Acer hotkey driver as /devices/virtual/input/input10 Jan 24 11:46:57 aao1 kernel: acerhk: Could not find model string, will assume type 200 series Jan 24 11:46:57 aao1 kernel: Acer Travelmate hotkey driver v0.5.35 Jan 24 11:46:57 aao1 kernel: EXT4-fs (sda4): mounted filesystem with ordered data mode Jan 24 11:46:57 aao1 kernel: Adding 1574360k swap on /dev/sda2. Priority:-1 extents:1 across:1574360k Jan 24 11:46:57 aao1 kernel: ip_tables: (C) 2000-2006 Netfilter Core Team Jan 24 11:46:57 aao1 kernel: nf_conntrack version 0.5.0 (16004 buckets, 64016 max) Jan 24 11:46:57 aao1 kernel: CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use Jan 24 11:46:57 aao1 kernel: nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or Jan 24 11:46:57 aao1 kernel: sysctl net.netfilter.nf_conntrack_acct=1 to enable it. Jan 24 11:46:57 aao1 kernel: NET: Registered protocol family 10 Jan 24 11:46:57 aao1 kernel: lo: Disabled Privacy Extensions Jan 24 11:46:57 aao1 kernel: ip6_tables: (C) 2000-2006 Netfilter Core Team Jan 24 11:46:58 aao1 acpid: starting up Jan 24 11:46:58 aao1 acpid: 4 rules loaded Jan 24 11:46:58 aao1 acpid: waiting for events: event logging is off Jan 24 11:46:58 aao1 laptop-mode: Laptop mode Jan 24 11:46:58 aao1 laptop-mode: enabled, not active Jan 24 11:46:59 aao1 /dev/sda: Jan 24 11:46:59 aao1 setting: standby to 244 (2 hours) Jan 24 11:46:47 aao1 load-modules.sh: 'acpi:LNXSYSTM:' is not a valid module or alias name Jan 24 11:46:47 aao1 load-modules.sh: 'pci:v00008086d000027A6sv00001025sd0000019Cbc03sc80i00' is not a valid module or alias name Jan 24 11:46:47 aao1 load-modules.sh: Not loading module 'pcspkr' for alias 'platform:pcspkr' because it is blacklisted Jan 24 11:46:47 aao1 load-modules.sh: 'pci:v00008086d00002448sv00000000sd00000000bc06sc04i01' is not a valid module or alias name Jan 24 11:46:47 aao1 load-modules.sh: 'acpi:LNXSYBUS:' is not a valid module or alias name Jan 24 11:46:48 aao1 load-modules.sh: 'platform:iTCO_wdt' is not a valid module or alias name Jan 24 11:46:48 aao1 load-modules.sh: 'acpi:device:' is not a valid module or alias name Jan 24 11:46:48 aao1 load-modules.sh: 'acpi:device:' is not a valid module or alias name Jan 24 11:46:48 aao1 load-modules.sh: 'acpi:device:' is not a valid module or alias name Jan 24 11:46:48 aao1 load-modules.sh: 'acpi:device:' is not a valid module or alias name Jan 24 11:46:48 aao1 load-modules.sh: 'acpi:device:' is not a valid module or alias name Jan 24 11:46:48 aao1 load-modules.sh: 'acpi:device:' is not a valid module or alias name Jan 24 11:46:48 aao1 load-modules.sh: 'acpi:device:' is not a valid module or alias name Jan 24 11:46:48 aao1 load-modules.sh: 'acpi:device:' is not a valid module or alias name Jan 24 11:46:48 aao1 load-modules.sh: 'acpi:device:' is not a valid module or alias name Jan 24 11:46:48 aao1 load-modules.sh: 'acpi:device:' is not a valid module or alias name Jan 24 11:46:48 aao1 load-modules.sh: 'acpi:device:' is not a valid module or alias name Jan 24 11:46:48 aao1 load-modules.sh: 'acpi:device:' is not a valid module or alias name Jan 24 11:46:48 aao1 load-modules.sh: 'acpi:device:' is not a valid module or alias name Jan 24 11:46:48 aao1 load-modules.sh: 'acpi:device:' is not a valid module or alias name Jan 24 11:46:48 aao1 load-modules.sh: 'acpi:device:' is not a valid module or alias name Jan 24 11:46:48 aao1 load-modules.sh: 'acpi:device:' is not a valid module or alias name Jan 24 11:46:48 aao1 load-modules.sh: 'usb:v0C45p62C0d0100dcEFdsc02dp01ic0Eisc02ip00' is not a valid module or alias name Jan 24 11:46:49 aao1 load-modules.sh: 'platform:regulatory' is not a valid module or alias name Jan 24 11:46:49 aao1 load-modules.sh: 'acpi:device:' is not a valid module or alias name Jan 24 11:46:49 aao1 load-modules.sh: 'acpi:PNP0000:' is not a valid module or alias name Jan 24 11:46:49 aao1 load-modules.sh: 'acpi:PNP0C02:' is not a valid module or alias name Jan 24 11:46:49 aao1 load-modules.sh: 'acpi:PNP0103:' is not a valid module or alias name Jan 24 11:46:49 aao1 load-modules.sh: 'acpi:PNP0100:' is not a valid module or alias name Jan 24 11:46:49 aao1 load-modules.sh: 'acpi:device:' is not a valid module or alias name Jan 24 11:46:49 aao1 load-modules.sh: 'acpi:PNP0303:' is not a valid module or alias name Jan 24 11:46:49 aao1 load-modules.sh: 'acpi:device:' is not a valid module or alias name Jan 24 11:46:49 aao1 load-modules.sh: 'acpi:PNP0200:' is not a valid module or alias name Jan 24 11:46:49 aao1 load-modules.sh: 'acpi:device:' is not a valid module or alias name Jan 24 11:46:49 aao1 load-modules.sh: 'acpi:device:' is not a valid module or alias name Jan 24 11:46:49 aao1 load-modules.sh: 'acpi:device:' is not a valid module or alias name Jan 24 11:46:49 aao1 load-modules.sh: 'acpi:device:' is not a valid module or alias name Jan 24 11:46:49 aao1 load-modules.sh: 'acpi:PNP0C04:' is not a valid module or alias name Jan 24 11:46:49 aao1 load-modules.sh: 'acpi:INT0800:' is not a valid module or alias name Jan 24 11:46:49 aao1 load-modules.sh: 'acpi:SYN1B1C:SYN1B00:SYN0002:PNP0F13:' is not a valid module or alias name Jan 24 11:46:49 aao1 load-modules.sh: 'acpi:device:' is not a valid module or alias name Jan 24 11:46:49 aao1 load-modules.sh: 'acpi:device:' is not a valid module or alias name Jan 24 11:46:49 aao1 load-modules.sh: 'acpi:device:' is not a valid module or alias name Jan 24 11:46:49 aao1 load-modules.sh: 'acpi:device:' is not a valid module or alias name Jan 24 11:46:49 aao1 load-modules.sh: 'acpi:device:' is not a valid module or alias name Jan 24 11:46:49 aao1 load-modules.sh: 'acpi:device:' is not a valid module or alias name Jan 24 11:46:49 aao1 load-modules.sh: 'acpi:device:' is not a valid module or alias name Jan 24 11:46:49 aao1 load-modules.sh: 'acpi:device:' is not a valid module or alias name Jan 24 11:46:49 aao1 load-modules.sh: 'acpi:device:' is not a valid module or alias name Jan 24 11:46:50 aao1 load-modules.sh: 'acpi:device:' is not a valid module or alias name Jan 24 11:46:50 aao1 load-modules.sh: 'acpi:device:' is not a valid module or alias name Jan 24 11:46:50 aao1 load-modules.sh: 'acpi:device:' is not a valid module or alias name Jan 24 11:46:50 aao1 load-modules.sh: 'acpi:device:' is not a valid module or alias name Jan 24 11:46:50 aao1 load-modules.sh: 'acpi:device:' is not a valid module or alias name Jan 24 11:46:50 aao1 load-modules.sh: 'acpi:device:' is not a valid module or alias name Jan 24 11:46:50 aao1 load-modules.sh: 'acpi:device:' is not a valid module or alias name Jan 24 11:46:50 aao1 load-modules.sh: 'acpi:device:' is not a valid module or alias name Jan 24 11:46:56 aao1 init: Entering runlevel: 3 Jan 24 11:47:01 aao1 acpid: client connected from 4007[82:82] Jan 24 11:47:01 aao1 acpid: 1 client rule loaded Jan 24 11:47:01 aao1 kernel: loop: module loaded Jan 24 11:47:02 aao1 cdemud[4047]: Starting daemon in daemon mode with following parameters: Jan 24 11:47:02 aao1 cdemud[4047]: - num devices: 1 Jan 24 11:47:02 aao1 cdemud[4047]: - ctl device: /dev/vhba_ctl Jan 24 11:47:02 aao1 cdemud[4047]: - audio driver: null Jan 24 11:47:02 aao1 cdemud[4047]: - bus type: system Jan 24 11:47:02 aao1 kernel: scsi 6:0:0:0: CD-ROM CDEmu Virt. CD/DVD-ROM 1.10 PQ: 0 ANSI: 0 Jan 24 11:47:02 aao1 kernel: scsi 6:0:0:0: Attached scsi generic sg1 type 5 Jan 24 11:47:02 aao1 kernel: sr0: scsi3-mmc drive: 40x/40x cd/rw xa/form2 cdda tray Jan 24 11:47:02 aao1 kernel: Uniform CD-ROM driver Revision: 3.20 Jan 24 11:47:04 aao1 kernel: ADDRCONF(NETDEV_UP): wlan0: link is not ready
Quoted 8 lines · Don Darling
Hello folks,
I recently tried upgrading to kernel version 2.6.32, but after this upgrade my wireless card became flaky when making connections. In cases where a connection can be established it is stable, but there are problems when making wireless associations. Downgrading to kernel version 2.6.31 resolves this issue. I'm not sure at the moment which versions of the ath5k driver maps to these kernel versions.
The (vanilla) kernel version is sufficient to know which driver it is.
Quoted 2 lines
I'm assuming this issue is related to the ath5k driver itself -- the network I'm using is only WEP128, and doesn't need
wpa_supplicant.
Huh, I didn't think any mac80211 driver supported WEP 128. Are you sure you weren't using madwifi before? Or maybe WEP 104?
Are you using any modparams with ath5k?
Quoted 2 lines
In fact, I have
fewer problems when I connect to WPA+TKIP networks withwpa_supplicant.
This is somewhat more secure, so I'd recommend it, or better CCMP.
Quoted 2 lines
Reverting to 2.6.31 resolves this issue. It will connect the first time, and I can disconnect/re-connect several times without issue.
I can't think of anything that changed in this time frame with ath5k specifically
having to do with crypto. If you were using nohwcrypt=1, it could be a problem with mac80211. Otherwise, bisecting might be the best route to pin it down.
Also on the off-chance that it's not crypto related, you may try the suggestions in the following to get a better picture of whwat is going on:
http://wireless.kernel.org/en/users/Documentation/Reporting_bugs
Signature · 1 line
Bob Copeland %% www.bobcopeland.com
Quoted 25 lines · Bob Copeland
Quoted 8 lines · Don Darling
Hello folks,
I recently tried upgrading to kernel version 2.6.32, but after this upgrade my wireless card became flaky when making connections. In cases where a connection can be established it is stable, but there are problems when making wireless associations. Downgrading to kernel version 2.6.31 resolves this issue. I'm not sure at the moment which versions of the ath5k driver maps to these kernel versions.
The (vanilla) kernel version is sufficient to know which driver it is.
Quoted 2 lines
I'm assuming this issue is related to the ath5k driver itself -- the network I'm using is only WEP128, and doesn't need
wpa_supplicant.Huh, I didn't think any mac80211 driver supported WEP 128. Are you sure you weren't using madwifi before? Or maybe WEP 104?
Are you using any modparams with ath5k?
Quoted 2 lines
In fact, I have
fewer problems when I connect to WPA+TKIP networks withwpa_supplicant.This is somewhat more secure, so I'd recommend it, or better CCMP.
Quoted 7 lines
Quoted 2 lines
Reverting to 2.6.31 resolves this issue. It will connect the first time, and I can disconnect/re-connect several times without issue.
I can't think of anything that changed in this time frame with ath5k specifically
having to do with crypto. If you were using nohwcrypt=1, it could be a problem with mac80211. Otherwise, bisecting might be the best route to pin it down.
One more important detail: wpa_supplicant can use both wext and nl80211, while iwconfig and networkmanager are wext-only.
Don: do you use -d wext or -d nl80211 with wpa_supplicant?
Quoted 13 lines
Also on the off-chance that it's not crypto related, you may try the suggestions in the following to get a better picture of whwat is going on:
http://wireless.kernel.org/en/users/Documentation/Reporting_bugs
--
Bob Copeland %% www.bobcopeland.com
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Signature · 1 line
Vista: [V]iruses, [I]ntruders, [S]pyware, [T]rojans and [A]dware. :-)
Quoted 6 lines · Bob Copeland
Quoted 2 lines · Don Darling
I'm assuming this issue is related to the ath5k driver itself -- the network I'm using is only WEP128, and doesn't need
wpa_supplicant.Huh, I didn't think any mac80211 driver supported WEP 128. Are you sure you weren't using madwifi before? Or maybe WEP 104?
For the record, WEP104 and WEP128 are the same thing. The smaller number makes it explicit that the 24-bit IV is transmitted in the open. The same thing applies to WEP40 and WEP64.
Larry
Quoted 17 lines · Larry Finger
Quoted 11 lines · Bob Copeland
Quoted 4 lines · Don Darling
I'm assuming this issue is related to the ath5k driver itself -- the network
I'm using is only WEP128, and doesn't needwpa_supplicant.Huh, I didn't think any mac80211 driver supported WEP 128. Are you sure you
weren't using madwifi before? Or maybe WEP 104?For the record, WEP104 and WEP128 are the same thing. The smaller number makes it explicit that the 24-bit IV is transmitted in the open. The same thing applies to WEP40 and WEP64.
Quoted 7 lines
Larry
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Only one problem there is another, nonstandard WEP type where the actual key is 128-bit, and this is also sometimes referred to as WEP128 (with the same metric as WEP64, this one would be WEP152). Same goes for "WEP228/WEP256/WEP280".
Signature · 1 line
Vista: [V]iruses, [I]ntruders, [S]pyware, [T]rojans and [A]dware. :-)
2010/1/25 Gábor Stefanik <[email protected]>:
Quoted 10 lines · Larry Finger
Quoted 4 lines
For the record, WEP104 and WEP128 are the same thing. The smaller number makes it explicit that the 24-bit IV is transmitted in the open. The same thing applies to WEP40 and WEP64.
Only one problem there is another, nonstandard WEP type where the actual key is 128-bit, and this is also sometimes referred to as WEP128 (with the same metric as WEP64, this one would be WEP152). Same goes for "WEP228/WEP256/WEP280".
Yea, I think ath hw supports that too:
#define AR5K_KEYTABLE_TYPE_40 0x00000000
#define AR5K_KEYTABLE_TYPE_104 0x00000001
#define AR5K_KEYTABLE_TYPE_128 0x00000003
at least that's what I assumed it meant. But there's no way to set it from mac80211 (nor should there be).
Signature · 1 line
Bob Copeland %% www.bobcopeland.com
Hello folks,
Thanks for the suggestions -- here are a few questions I can answer from earlier today:
1) I didn't realize there was a subtle difference between WEP104 and WEP128. What I can tell you is that the WEP AP is running Tomato 1.23, and is set to WEP 128-bit. However, the key I'm using is only 104 bits. This probably means I'm actually using WEP104.
2) I'm definitely not using madwifi in either case -- I've always used the ath5k driver on this machine.
3) As far as I can tell, there are no modparams being used with ath5k. I checked both /etc/modprobe.d and /etc/sysctl.conf (I'm not sure if the latter affects modules or not, actually - I think it might depend on the module).
4) I realize WPA+TKIP is more secure and I would use it if I could, but I have some old devices that don't support WPA it so I'm limited to WEP.
5) I use -Dwext with wpa_supplicant when I *do* use WPA+TKIP networks.
Also, FWIW:
# lsmod | grep ath ath5k 127364 0 mac80211 155788 1 ath5k ath 7708 1 ath5k cfg80211 90364 3 ath5k,mac80211,ath led_class 4000 1 ath5k
I'm not sure when I might have a chance to bisect, but will certainly let you know if I do.
Best regards,
Don
Quoted 25 lines · Bob Copeland
2010/1/25 Gábor Stefanik <[email protected]>:
Quoted 7 lines · Larry Finger
Quoted 6 lines
For the record, WEP104 and WEP128 are the same thing. The smaller number makes it explicit that the 24-bit IV is transmitted in the open. The same thing applies to WEP40 and WEP64.
Quoted 5 lines
Only one problem there is another, nonstandard WEP type where the actual key is 128-bit, and this is also sometimes referred to as WEP128 (with the same metric as WEP64, this one would be WEP152). Same goes for "WEP228/WEP256/WEP280".
Yea, I think ath hw supports that too:
#define
AR5K_KEYTABLE_TYPE_400x00000000
#defineAR5K_KEYTABLE_TYPE_1040x00000001
#defineAR5K_KEYTABLE_TYPE_1280x00000003at least that's what I assumed it meant. But there's no way to set it from mac80211 (nor should there be).
Quoted 11 lines · Don Darling
Hello folks,
I recently tried upgrading to kernel version 2.6.32, but after this upgrade my wireless card became flaky when making connections. In cases where a connection can be established it is stable, but there are problems when making wireless associations. Downgrading to kernel version 2.6.31 resolves this issue. I'm not sure at the moment which versions of the ath5k driver maps to these kernel versions.
Here is a brief description of my system:
hi,
i can confirm don's issue. i have been using several revisions of 2.6.32 (debian, not vanilla, it's true), i have resorted (back) to using ath-pci
instead (i had been using it before because of the nifty functionality, but i
switched to ath5k lately because of it being included in the kernel).
reading don's report here, i tried using the 2.6.30 i already have, it seems
to work fine.
i can test pretty much whatever is needed, so feel free to ask.
here is the working ath5k details:
the laptop is a compaq nc6000,
the card:
lspci | grep -i ath
02:04.0 Ethernet controller: Atheros Communications Inc. Atheros AR5001X+
Wireless Network Adapter (rev 01)
modinfo ath5k
filename:/lib/modules/2.6.30-2-686/kernel/drivers/net/wireless/ath5k/ath5k.ko
version: 0.6.0 (EXPERIMENTAL) license: Dual BSD/GPL description: Support for 5xxx series of Atheros 802.11 wireless LAN cards. author: Nick Kossifidis author: Jiri Slaby srcversion: EE1D08AEEC0159304E1A703
modinfo mac80211
filename:/lib/modules/2.6.30-2-686/kernel/net/mac80211/mac80211.ko
license: GPL description: IEEE 802.11 subsystem depends: cfg80211 vermagic: 2.6.30-2-686 SMP mod_unload modversions 686 parm: ieee80211_default_rc_a
modinfo cfg80211
filename:/lib/modules/2.6.30-2-686/kernel/net/wireless/cfg80211.ko
description: wireless configuration support license: GPL author: Johannes Berg depends: vermagic: 2.6.30-2-686 SMP mod_unload modversions 686 parm: ieee80211_regdom:IEEE 802.11 regulatory domain code
(charp)
problematic ath5k:
filename:/lib/modules/2.6.32-3-686/kernel/drivers/net/wireless/ath/ath5k/ath5k.ko
version: 0.6.0 (EXPERIMENTAL) license: Dual BSD/GPL description: Support for 5xxx series of Atheros 802.11 wireless LAN cards. author: Nick Kossifidis author: Jiri Slaby srcversion: DEA0BE918B6E0D0429CDF27
(same version, 0.6.0, but different src version).
hope this helps
ps: i am also having a seldom kernel panic issue, i cannot confirm if it has
anything to do with ath5k, but it did happen once or twice when inserting or
removing the module. i also had issues bringing the interface up after inserting ath5k, i would get "error 132". again, no idea if any of this is
related.
--
nanok
ps2: "You have lines longer than 80 characters. Fix that.". huh? why doesn't the webform just enforce that instead? very annoying :(
Quoted 11 lines · nanok
i can confirm don's issue. i have been using several revisions of 2.6.32 (debian, not vanilla, it's true), i have resorted (back) to using ath-pci
instead (i had been using it before because of the nifty functionality, but i
switched to ath5k lately because of it being included in the kernel).reading don's report here, i tried using the 2.6.30 i already have, it seems
to work fine
As you are using debian I have to ask: have you installed crda? Since 2.6.30 ath5k gained regulatory support which may cause certain channels to be disabled.
Signature · 1 line
Bob Copeland %% www.bobcopeland.com
Quoted 3 lines · Bob Copeland
As you are using debian I have to ask: have you installed crda? Since 2.6.30 ath5k gained regulatory support which may cause certain channels to be disabled.
By "since 2.6.30" I meant post-2.6.30, sorry for any confusion.
Signature · 1 line
Bob Copeland %% www.bobcopeland.com
Quoted 12 lines · Bob Copeland
Quoted 3 lines · Bob Copeland
As you are using debian I have to ask: have you installed crda? ?Since 2.6.30 ath5k gained regulatory support which may cause certain channels to be disabled.
By "since 2.6.30" I meant post-2.6.30, sorry for any confusion.
Signature · 1 line
Bob Copeland %% www.bobcopeland.com
hi Bob,
no confusion, it's perfectly clear either way you state it. unfortunately, it's 2.6.3
0 that "works" (not pre-2.6.30), or did you mean since 2.6.30, excluding 2.6.30?
anyway, not sure why the crda would affect only wep operation, but here's a snip of o
ne of my /var/log/messages, see if it helps (not sure i got where you are aiming, so forgive me if this isn't what you need to know)
Mar 16 16:50:51 spartakus kernel: [14842.518127] cfg80211: Using static regulatory domain info Mar 16 16:50:51 spartakus kernel: [14842.518130] cfg80211: Regulatory domain: US Mar 16 16:50:51 spartakus kernel: [14842.518133] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) Mar 16 16:50:51 spartakus kernel: [14842.518137] (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm) Mar 16 16:50:51 spartakus kernel: [14842.518141] (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) Mar 16 16:50:51 spartakus kernel: [14842.518145] (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) Mar 16 16:50:51 spartakus kernel: [14842.518148] (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) Mar 16 16:50:51 spartakus kernel: [14842.518152] (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) Mar 16 16:50:51 spartakus kernel: [14842.518156] (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm) Mar 16 16:50:51 spartakus kernel: [14842.518395] cfg80211: Calling CRDA for country: US Mar 16 16:50:51 spartakus kernel: [14842.551365] ath5k 0000:02:04.0: PCI INT A -> Link[C0C7] -> GSI 11 (level, low) -> IRQ 11 Mar 16 16:50:51 spartakus kernel: [14842.551412] ath5k 0000:02:04.0: registered as 'phy0' Mar 16 16:50:51 spartakus kernel: [14842.798956] Registered led device: ath5k-phy0::rx Mar 16 16:50:51 spartakus kernel: [14842.800364] Registered led device: ath5k-phy0::tx Mar 16 16:50:51 spartakus kernel: [14842.800370] ath5k phy0: Atheros AR5212 chip found (MAC: 0x56, PHY: 0x41) Mar 16 16:50:51 spartakus kernel: [14842.800373] ath5k phy0: RF5111 5GHz radio found (0x17) Mar 16 16:50:51 spartakus kernel: [14842.800376] ath5k phy0: RF2111 2GHz radio found (0x23) Mar 16 16:50:57 spartakus kernel: [14849.209305] ADDRCONF(NETDEV_UP): wlan0: link is not ready
Linux version 2.6.32-3-686 (Debian 2.6.32-9) (maks @debian.org) (gcc version 4.3.4 (Debian 4.3.4-8) ) #1 SMP Thu Feb 25 06:14:20 UTC 2010
note: the above is not from a particular working/non working session, it just illustrates (somehting to do with) crda. to obtain logs from a particular scenario, i would need ot test specifically, to be sure what happened when (however, as far as i remember, there's nothing "interesting" in the logs when it won't work, in most cases it looks the same)
Signature · 1 line
nanok
Quoted 14 lines · nanok
Quoted 6 lines · Bob Copeland
Quoted 3 lines · Bob Copeland
As you are using debian I have to ask: have you installed crda? ?Since 2.6.30 ath5k gained regulatory support which may cause certain channels to be disabled.
Quoted 6 lines
By "since 2.6.30" I meant post-2.6.30, sorry for any confusion.
--
Bob Copeland %% www.bobcopeland.com
Quoted 6 lines
hi Bob,
no confusion, it's perfectly clear either way you state it. unfortunately, it's 2.6.3
0 that "works" (not pre-2.6.30), or did you mean since 2.6.30, excluding 2.6.30?
Right, that is what I tried to correct. _After_ 2.6.30, ath5k began reporting the regdomain from the EEPROM which means some channels (13 is a common case) are no longer accessible whereas they were before with static reg domains and no EEPROM support. That was the major change in the driver. Most other changes since 2.6.30 were in the upper-layers. I don't recall any changes to crypto in that timeframe.
WRT to the original report, is only WEP causing problems (i.e. does WPA work?)
Signature · 1 line
Bob Copeland %% www.bobcopeland.com
Quoted 31 lines · Bob Copeland
Quoted 14 lines · nanok
Quoted 6 lines · Bob Copeland
Quoted 3 lines · Bob Copeland
As you are using debian I have to ask: have you installed crda? ?Since 2.6.30 ath5k gained regulatory support which may cause certain channels to be disabled.
Quoted 6 lines
By "since 2.6.30" I meant post-2.6.30, sorry for any confusion.
--
Bob Copeland %% www.bobcopeland.comQuoted 6 lines
hi Bob,
no confusion, it's perfectly clear either way you state it. unfortunately, it's 2.6.3
0 that "works" (not pre-2.6.30), or did you mean since 2.6.30, excluding 2.6.30?Right, that is what I tried to correct. _After_ 2.6.30, ath5k began reporting the regdomain from the EEPROM which means some channels (13 is a common case) are no longer accessible whereas they were before with static reg domains and no EEPROM support. That was the major change in the driver. Most other changes since 2.6.30 were in the upper-layers. I don't recall any changes to crypto in that timeframe.
Quoted 6 lines
WRT to the original report, is only WEP causing problems (i.e. does WPA work?)
Signature · 1 line
Bob Copeland %% www.bobcopeland.com
wpa works with wpa_supplicant, i haven't tested in a while, but i can as soon as i get home. plain also works (no encryption). iirc, the original "plaintif" experienced the same.
to keep things accurate, i have experienced again a lock up (kernel panick) while i was trying to get the wlan0 up (ath5k), and getting errors, so now i have switched back to ath-pci (madwifi). there might be something wrong with my hardware (additionally).
Signature · 1 line
nanok
Quoted 7 lines · nanok
wpa works with
wpa_supplicant, i haven't tested in a while, but i can as soon as i get home. plain also works (no encryption). iirc, the original "plaintif" experienced the same.to keep things accurate, i have experienced again a lock up (kernel panick) while i was trying to get the wlan0 up (ath5k), and getting errors, so now i have switched back to ath-pci
If you can manage to capture the panic, that would be helpful, for example by switching to a console beforehand and taking a picture with a digital camera.
(Still wishing for KMS to solve this problem...)
Signature · 1 line
Bob Copeland %% www.bobcopeland.com