Skip to contentSkip to conversation

ata: libata-core: Add ATA_HORKAGE_NOLPM for Apacer AS340

PATCH Applied Niklas Cassel 3 participants 6 messages May 30, 2024 – May 31, 2024

Subsystems (2)
lore
Share & tools
lore

Niklas Cassel

author maintainer
#0 lore raw

PATCH 1/1 ata: libata-core: Add ATA_HORKAGE_NOLPM for Apacer AS340

Commit 7627a0edef54 ("ata: ahci: Drop low power policy board type") dropped the board_ahci_low_power board type, and instead enables LPM if:
-The AHCI controller reports that it supports LPM (Partial/Slumber), and -CONFIG_SATA_MOBILE_LPM_POLICY != 0, and
-The port is not defined as external in the per port PxCMD register, and -The port is not defined as hotplug capable in the per port PxCMD
register.

Partial and Slumber LPM states can either be initiated by HIPM or DIPM.

For HIPM (host initiated power management) to get enabled, both the AHCI controller and the drive have to report that they support HIPM.

For DIPM (device initiated power management) to get enabled, only the drive has to report that it supports DIPM. However, the HBA will reject device requests to enter LPM states which the HBA does not support.

The problem is that Apacer AS340 drives do not handle low power modes correctly. The problem was most likely not seen before because no one had used this drive with a AHCI controller with LPM enabled.

Add a quirk so that we do not enable LPM for this drive, since we see command timeouts if we do (even though the drive claims to support DIPM).

Fixes 7627a0edef54 ("ata: ahci: Drop low power policy board type")

---
On the system reporting this issue, the HBA supports SALP (HIPM) and LPM states Partial and Slumber.

This drive only supports DIPM but not HIPM, however, that should not matter, as a DIPM request from the device still has to be acked by the HBA, and according to AHCI 1.3.1, section 5.3.2.11 P:Idle, if the link layer has negotiated to low power state based on device power management request, the HBA will jump to state PM:LowPower.

In PM:LowPower, the HBA will automatically request to wake the link (exit from Partial/Slumber) when a new command is queued (by writing to PxCI). Thus, there should be no need for host software to request an explicit wakeup (by writing PxCMD.ICC to 1).

Therefore, even with only DIPM supported/enabled, we shouldn't see command timeouts with the current code. Also, only enabling only DIPM (by modifying the AHCI driver) with another drive (which support both DIPM and HIPM), shows no errors. Thus, it seems like the drive is the problem.

 drivers/ata/libata-core.c | 3 +++
 1 file changed, 3 insertions(+)
drivers/ata/libata-core.c +3 -0
index 4f35aab81a0a..25b400f1c3de 100644
@@ -4155,6 +4155,9 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = {
 						ATA_HORKAGE_ZERO_AFTER_TRIM |
 						ATA_HORKAGE_NOLPM },
 
+	/* Apacer models with LPM issues */
+	{ "Apacer AS340*",		NULL,	ATA_HORKAGE_NOLPM },
+
 	/* These specific Samsung models/firmware-revs do not handle LPM well */
 	{ "SAMSUNG MZMPC128HBFU-000MV", "CXM14M1Q", ATA_HORKAGE_NOLPM },
 	{ "SAMSUNG SSD PM830 mSATA *",  "CXM13D1Q", ATA_HORKAGE_NOLPM },
Signature · 1 line
2.45.1
author maintainer
#1 lore raw
Quoted 69 lines · Niklas Cassel

Commit 7627a0edef54 ("ata: ahci: Drop low power policy board type") dropped the board_ahci_low_power board type, and instead enables LPM if:

(quoted diff) +0 -4
-The AHCI controller reports that it supports LPM (Partial/Slumber), and
-CONFIG_SATA_MOBILE_LPM_POLICY != 0, and
-The port is not defined as external in the per port PxCMD register, and
-The port is not defined as hotplug capable in the per port PxCMD
 register.

Partial and Slumber LPM states can either be initiated by HIPM or DIPM.

For HIPM (host initiated power management) to get enabled, both the AHCI controller and the drive have to report that they support HIPM.

For DIPM (device initiated power management) to get enabled, only the drive has to report that it supports DIPM. However, the HBA will reject device requests to enter LPM states which the HBA does not support.

The problem is that Apacer AS340 drives do not handle low power modes correctly. The problem was most likely not seen before because no one had used this drive with a AHCI controller with LPM enabled.

Add a quirk so that we do not enable LPM for this drive, since we see command timeouts if we do (even though the drive claims to support DIPM).

Fixes 7627a0edef54 ("ata: ahci: Drop low power policy board type")

---
On the system reporting this issue, the HBA supports SALP (HIPM) and LPM states Partial and Slumber.

This drive only supports DIPM but not HIPM, however, that should not matter, as a DIPM request from the device still has to be acked by the HBA, and according to AHCI 1.3.1, section 5.3.2.11 P:Idle, if the link layer has negotiated to low power state based on device power management request, the HBA will jump to state PM:LowPower.

In PM:LowPower, the HBA will automatically request to wake the link (exit from Partial/Slumber) when a new command is queued (by writing to PxCI). Thus, there should be no need for host software to request an explicit wakeup (by writing PxCMD.ICC to 1).

Therefore, even with only DIPM supported/enabled, we shouldn't see command timeouts with the current code. Also, only enabling only DIPM (by modifying the AHCI driver) with another drive (which support both DIPM and HIPM), shows no errors. Thus, it seems like the drive is the problem.

 drivers/ata/libata-core.c | 3 +++
 1 file changed, 3 insertions(+)
drivers/ata/libata-core.c +3 -0
index 4f35aab81a0a..25b400f1c3de 100644
@@ -4155,6 +4155,9 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = {
 						ATA_HORKAGE_ZERO_AFTER_TRIM |
 						ATA_HORKAGE_NOLPM },
 
+	/* Apacer models with LPM issues */
+	{ "Apacer AS340*",		NULL,	ATA_HORKAGE_NOLPM },
+
 	/* These specific Samsung models/firmware-revs do not handle LPM well */
 	{ "SAMSUNG MZMPC128HBFU-000MV", "CXM14M1Q", ATA_HORKAGE_NOLPM },
 	{ "SAMSUNG SSD PM830 mSATA *",  "CXM13D1Q", ATA_HORKAGE_NOLPM },
Signature · 1 line
2.45.1

One interesting fact which:
Apacer AS340, CT240BX500SSD1, and R3SL240G all have in common:
their SSD controller is made by Silicon Motion:
https://smarthdd.com/database/Apacer-AS340-120GB/U1014A0/
https://smarthdd.com/database/CT240BX500SSD1/M6CR013/
https://smarthdd.com/database/R3SL240G/P0422C/

Not sure if that is relevant or not...

Kind regards,
Niklas

maintainer
#2 lore raw
Quoted 78 lines · Niklas Cassel
Quoted 69 lines · Niklas Cassel

Commit 7627a0edef54 ("ata: ahci: Drop low power policy board type") dropped the board_ahci_low_power board type, and instead enables LPM if:

(quoted diff) +0 -4
-The AHCI controller reports that it supports LPM (Partial/Slumber), and
-CONFIG_SATA_MOBILE_LPM_POLICY != 0, and
-The port is not defined as external in the per port PxCMD register, and
-The port is not defined as hotplug capable in the per port PxCMD
 register.

Partial and Slumber LPM states can either be initiated by HIPM or DIPM.

For HIPM (host initiated power management) to get enabled, both the AHCI controller and the drive have to report that they support HIPM.

For DIPM (device initiated power management) to get enabled, only the drive has to report that it supports DIPM. However, the HBA will reject device requests to enter LPM states which the HBA does not support.

The problem is that Apacer AS340 drives do not handle low power modes correctly. The problem was most likely not seen before because no one had used this drive with a AHCI controller with LPM enabled.

Add a quirk so that we do not enable LPM for this drive, since we see command timeouts if we do (even though the drive claims to support DIPM).

Fixes 7627a0edef54 ("ata: ahci: Drop low power policy board type")

---
On the system reporting this issue, the HBA supports SALP (HIPM) and LPM states Partial and Slumber.

This drive only supports DIPM but not HIPM, however, that should not matter, as a DIPM request from the device still has to be acked by the HBA, and according to AHCI 1.3.1, section 5.3.2.11 P:Idle, if the link layer has negotiated to low power state based on device power management request, the HBA will jump to state PM:LowPower.

In PM:LowPower, the HBA will automatically request to wake the link (exit from Partial/Slumber) when a new command is queued (by writing to PxCI). Thus, there should be no need for host software to request an explicit wakeup (by writing PxCMD.ICC to 1).

Therefore, even with only DIPM supported/enabled, we shouldn't see command timeouts with the current code. Also, only enabling only DIPM (by modifying the AHCI driver) with another drive (which support both DIPM and HIPM), shows no errors. Thus, it seems like the drive is the problem.

 drivers/ata/libata-core.c | 3 +++
 1 file changed, 3 insertions(+)
drivers/ata/libata-core.c +3 -0
index 4f35aab81a0a..25b400f1c3de 100644
@@ -4155,6 +4155,9 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = {
 						ATA_HORKAGE_ZERO_AFTER_TRIM |
 						ATA_HORKAGE_NOLPM },
 
+	/* Apacer models with LPM issues */
+	{ "Apacer AS340*",		NULL,	ATA_HORKAGE_NOLPM },
+
 	/* These specific Samsung models/firmware-revs do not handle LPM well */
 	{ "SAMSUNG MZMPC128HBFU-000MV", "CXM14M1Q", ATA_HORKAGE_NOLPM },
 	{ "SAMSUNG SSD PM830 mSATA *",  "CXM13D1Q", ATA_HORKAGE_NOLPM },
Signature · 1 line
2.45.1

One interesting fact which:
Apacer AS340, CT240BX500SSD1, and R3SL240G all have in common:
their SSD controller is made by Silicon Motion:
https://smarthdd.com/database/Apacer-AS340-120GB/U1014A0/
https://smarthdd.com/database/CT240BX500SSD1/M6CR013/
https://smarthdd.com/database/R3SL240G/P0422C/

Quoted 1 line

Not sure if that is relevant or not...

Well, I guess that probably explains why they all have the same issue with LPM.

Signature · 2 lines
Damien Le Moal
Western Digital Research
maintainer Reviewed-by on v1 1/1
#3 lore raw
In reply to Niklas Cassel
Quoted 21 lines · Niklas Cassel

Commit 7627a0edef54 ("ata: ahci: Drop low power policy board type") dropped the board_ahci_low_power board type, and instead enables LPM if:

(quoted diff) +0 -4
-The AHCI controller reports that it supports LPM (Partial/Slumber), and
-CONFIG_SATA_MOBILE_LPM_POLICY != 0, and
-The port is not defined as external in the per port PxCMD register, and
-The port is not defined as hotplug capable in the per port PxCMD
 register.

Partial and Slumber LPM states can either be initiated by HIPM or DIPM.

For HIPM (host initiated power management) to get enabled, both the AHCI controller and the drive have to report that they support HIPM.

For DIPM (device initiated power management) to get enabled, only the drive has to report that it supports DIPM. However, the HBA will reject device requests to enter LPM states which the HBA does not support.

The problem is that Apacer AS340 drives do not handle low power modes correctly. The problem was most likely not seen before because no one had used this drive with a AHCI controller with LPM enabled.

Quoted 8 lines

Add a quirk so that we do not enable LPM for this drive, since we see command timeouts if we do (even though the drive claims to support DIPM).

Fixes 7627a0edef54 ("ata: ahci: Drop low power policy board type")
Signature · 2 lines
Damien Le Moal
Western Digital Research
Reviewed-by on v1 1/1
#4 lore raw
In reply to Niklas Cassel
Quoted 21 lines · Niklas Cassel

Commit 7627a0edef54 ("ata: ahci: Drop low power policy board type") dropped the board_ahci_low_power board type, and instead enables LPM if:

(quoted diff) +0 -4
-The AHCI controller reports that it supports LPM (Partial/Slumber), and
-CONFIG_SATA_MOBILE_LPM_POLICY != 0, and
-The port is not defined as external in the per port PxCMD register, and
-The port is not defined as hotplug capable in the per port PxCMD
 register.

Partial and Slumber LPM states can either be initiated by HIPM or DIPM.

For HIPM (host initiated power management) to get enabled, both the AHCI controller and the drive have to report that they support HIPM.

For DIPM (device initiated power management) to get enabled, only the drive has to report that it supports DIPM. However, the HBA will reject device requests to enter LPM states which the HBA does not support.

The problem is that Apacer AS340 drives do not handle low power modes correctly. The problem was most likely not seen before because no one had used this drive with a AHCI controller with LPM enabled.

Quoted 8 lines

Add a quirk so that we do not enable LPM for this drive, since we see command timeouts if we do (even though the drive claims to support DIPM).

Fixes 7627a0edef54 ("ata: ahci: Drop low power policy board type")
author maintainer Applied
#5 lore raw
In reply to Niklas Cassel

Review

Quoted 9 lines · Niklas Cassel

Commit 7627a0edef54 ("ata: ahci: Drop low power policy board type") dropped the board_ahci_low_power board type, and instead enables LPM if:

(quoted diff) +0 -4
-The AHCI controller reports that it supports LPM (Partial/Slumber), and
-CONFIG_SATA_MOBILE_LPM_POLICY != 0, and
-The port is not defined as external in the per port PxCMD register, and
-The port is not defined as hotplug capable in the per port PxCMD
 register.
 
[...]

Applied, thanks!

[1/1] ata: libata-core: Add ATA_HORKAGE_NOLPM for Apacer AS340

      commit: 3cb648c4dd3e8dde800fb3659250ed11f2d9efa5

Best regards,

Signature · 1 line
Niklas Cassel <[email protected]>