arm64: dts/bindings: Add support for BeagleBadge
Subsystems (2)
cover arm64: dts/bindings: Add support for BeagleBadge
Hi,
BeagleBoard.org BeagleBadge[1] is a compact, affordable open source hardware [2] single board computer based on the Texas Instruments AM62L3 SoC designed for IoT and embedded applications. Add base support for the same.
Bootlog: https://gist.github.com/jmenti/d85f17bf5264f1364866df91e60231eb
This patch series adds:
- Device tree bindings update for am62l3-badge
- Device tree source for BeagleBadge board
[0] https://beagleboard.org/
[1] https://www.beagleboard.org/boards/beaglebadge
[2] https://github.com/beagleboard/BeagleBadge/blob/main/design/BeagleBadge_RevA_V0.7_SCH_251107.pdf
Judith Mendez (2):
dt-bindings: arm: ti: Add am62l3-badge
arm64: dts: ti: Add k3-am62l3-beaglebadge
.../devicetree/bindings/arm/ti/k3.yaml | 1 + arch/arm64/boot/dts/ti/Makefile | 1 + arch/arm64/boot/dts/ti/k3-am62l3-badge.dts | 655 ++++++++++++++++++ 3 files changed, 657 insertions(+) create mode 100644 arch/arm64/boot/dts/ti/k3-am62l3-badge.dts
Signature · 1 line
2.53.0
PATCH 1/2 dt-bindings: arm: ti: Add am62l3-badge
This board is based on ti,am62l3
https://beagleboard.org/
https://github.com/beagleboard/BeagleBadge
--- Documentation/devicetree/bindings/arm/ti/k3.yaml | 1 + 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/arm/ti/k3.yaml +1 -0
@@ -40,6 +40,7 @@ properties: - description: K3 AM62L3 SoC and Boards items: - enum: + - beagle,am62l3-badge - ti,am62l3-evm - const: ti,am62l3
Signature · 1 line
2.53.0
PATCH 2/2 arm64: dts: ti: Add k3-am62l3-beaglebadge
In reply to Judith MendezBeagleBoard.org BeagleBadge is a compact, affordable open source hardware single board computer based on the Texas Instruments AM62L3 SoC designed for IoT and embedded applications with low power consumption. Expansion is provided over open standards based headers including QWIIC and GPIO interfaces.
https://beagleboard.org/
https://github.com/beagleboard/BeagleBadge
--- arch/arm64/boot/dts/ti/Makefile | 1 + arch/arm64/boot/dts/ti/k3-am62l3-badge.dts | 655 +++++++++++++++++++++ 2 files changed, 656 insertions(+) create mode 100644 arch/arm64/boot/dts/ti/k3-am62l3-badge.dts
arch/arm64/boot/dts/ti/Makefile +1 -0
@@ -41,6 +41,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-am62d2-evm.dtb # Boards with AM62Lx SoCs dtb-$(CONFIG_ARCH_K3) += k3-am62l3-evm.dtb +dtb-$(CONFIG_ARCH_K3) += k3-am62l3-badge.dtb # Boards with AM62Px SoC dtb-$(CONFIG_ARCH_K3) += k3-am62p5-sk.dtb
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts new file +655 -0
655 lines not on this page · raw message
Signature · 1 line
2.53.0
Re: [PATCH 2/2] arm64: dts: ti: Add k3-am62l3-beaglebadge
Quoted 10 lines · Judith Mendez
BeagleBoard.org BeagleBadge is a compact, affordable open source hardware single board computer based on the Texas Instruments AM62L3 SoC designed for IoT and embedded applications with low power consumption. Expansion is provided over open standards based headers including QWIIC and GPIO interfaces.
https://beagleboard.org/
https://github.com/beagleboard/BeagleBadgeCo-developed-by Andrew Davis <[email protected]>
Incomplete DCO. Please read carefully submitting patches to understand what you should do here.
Quoted 1 line
Signed-off-by Judith Mendez <[email protected]>
...
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts line 650
Quoted 6 lines
+&spi3 {
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts new file +5
-0+ pinctrl-names = "default"; + pinctrl-0 = <&spi3_pins_default>; + status = "okay"; + + sx1262_lora: lora@0 {
Heh? Lora?
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts line 651
Quoted 1 line
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts new file +1
-0+ compatible = "rohm,dh2228fv";
Nope, you don't have this device. Stop faking stuff. dh2228fv DOES NOT EXIST! How could you put to hardware something which does not even exist?
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts line 643
Quoted 4 lines
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts new file +4
-0+ reg = <0>; + spi-max-frequency = <10000000>; + }; +};
Best regards,
Krzysztof
Re: [PATCH 2/2] arm64: dts: ti: Add k3-am62l3-beaglebadge
Hi,
Quoted 7 lines · Krzysztof Kozlowski
Quoted 6 lines · Judith Mendez
BeagleBoard.org BeagleBadge is a compact, affordable open source hardware single board computer based on the Texas Instruments AM62L3 SoC designed for IoT and embedded applications with low power consumption. Expansion is provided over open standards based headers including QWIIC and GPIO interfaces.
Quoted 7 lines
Quoted 4 lines
https://beagleboard.org/
https://github.com/beagleboard/BeagleBadgeCo-developed-by Andrew Davis <[email protected]>Incomplete DCO. Please read carefully submitting patches to understand what you should do here.
Will fix, thanks.
Quoted 14 lines
Quoted 2 lines
Signed-off-by Judith Mendez <[email protected]>...
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts line 650
Quoted 6 lines
+&spi3 {
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts new file +5
-0+ pinctrl-names = "default"; + pinctrl-0 = <&spi3_pins_default>; + status = "okay"; + + sx1262_lora: lora@0 {Heh? Lora?
Quoted 4 lines
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts line 651
Quoted 1 line
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts new file +1
-0+ compatible = "rohm,dh2228fv";Nope, you don't have this device. Stop faking stuff. dh2228fv DOES NOT EXIST! How could you put to hardware something which does not even exist?
Will remove this node and respin the series.
~ Judith
Re: [PATCH 2/2] arm64: dts: ti: Add k3-am62l3-beaglebadge
In reply to Judith MendezQuoted 623 lines · Judith Mendez
BeagleBoard.org BeagleBadge is a compact, affordable open source hardware single board computer based on the Texas Instruments AM62L3 SoC designed for IoT and embedded applications with low power consumption. Expansion is provided over open standards based headers including QWIIC and GPIO interfaces.
https://beagleboard.org/
https://github.com/beagleboard/BeagleBadgeCo-developed-by Andrew Davis <[email protected]>Signed-off-by Judith Mendez <[email protected]>--- arch/arm64/boot/dts/ti/Makefile | 1 + arch/arm64/boot/dts/ti/k3-am62l3-badge.dts | 655 +++++++++++++++++++++ 2 files changed, 656 insertions(+)create mode 100644
arch/arm64/boot/dts/ti/k3-am62l3-badge.dtsarch/arm64/boot/dts/ti/Makefile +1
-0@@ -41,6 +41,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-am62d2-evm.dtb # Boards with AM62Lx SoCs dtb-$(CONFIG_ARCH_K3) += k3-am62l3-evm.dtb +dtb-$(CONFIG_ARCH_K3) += k3-am62l3-badge.dtb # Boards with AM62Px SoC dtb-$(CONFIG_ARCH_K3) += k3-am62p5-sk.dtbarch/arm64/boot/dts/ti/k3-am62l3-badge.dts new file +588
-0@@ -0,0 +1,655 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * https://www.beagleboard.org/boards/beaglebadge + * + * Copyright (C) 2026 Texas Instruments Incorporated - https://www.ti.com/ + */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/net/ti-dp83867.h> +#include "k3-am62l3.dtsi" +#include "k3-pinctrl.h" + +/ { + compatible = "beagle,am62l3-badge", "ti,am62l3"; + model = "BeagleBoard.org BeagleBadge"; + + chosen { + stdout-path = &uart0; + }; + + aliases { + gpio0 = &gpio0; + gpio1 = &gpio2; + gpio2 = &wkup_gpio0; + i2c0 = &i2c0; + i2c1 = &i2c1; + i2c4 = &wkup_i2c0; + mmc1 = &sdhci1; + mmc2 = &sdhci2; + serial3 = &uart1; + usb0 = &usb0; + usb1 = &usb1; + }; + + memory@80000000 { + /* 256MB */ + reg = <0x00000000 0x80000000 0x00000000 0x10000000>; + device_type = "memory"; + bootph-all; + }; + + gpio_keys: gpio-keys { + compatible = "gpio-keys"; + autorepeat; + pinctrl-names = "default"; + pinctrl-0 = <&usr_button_default_pins>; + + button-select { + label = "SELECT"; + linux,code = <KEY_SELECT>; + gpios = <&gpio0 26 GPIO_ACTIVE_LOW>; + }; + + button-back { + label = "BACK"; + linux,code = <KEY_BACK>; + gpios = <&gpio0 104 GPIO_ACTIVE_LOW>; + }; + + button-up { + label = "UP"; + linux,code = <KEY_UP>; + gpios = <&gpio0 32 GPIO_ACTIVE_LOW>; + }; + + button-down { + label = "DOWN"; + linux,code = <KEY_DOWN>; + gpios = <&gpio0 42 GPIO_ACTIVE_LOW>; + }; + + button-left { + label = "LEFT"; + linux,code = <KEY_LEFT>; + gpios = <&gpio0 31 GPIO_ACTIVE_LOW>; + }; + + button-right { + label = "RIGHT"; + linux,code = <KEY_RIGHT>; + gpios = <&gpio0 95 GPIO_ACTIVE_LOW>; + }; + }; + + multicolor-led { + compatible = "pwm-leds-multicolor"; + pinctrl-names = "default"; + pinctrl-0 = <&rgb_led_default_pins>; + + multi-led { + color = <LED_COLOR_ID_RGB>; + max-brightness = <255>; + + led-red { + pwms = <&ecap2 0 255 0>; + color = <LED_COLOR_ID_RED>; + }; + + led-green { + pwms = <&ecap1 0 255 0>; + color = <LED_COLOR_ID_GREEN>; + }; + + led-blue { + pwms = <&epwm1 1 255 0>; + color = <LED_COLOR_ID_BLUE>; + }; + }; + }; + + seven-segment-left { + compatible = "gpio-7-segment"; + segment-gpios = <&mcp23s18 0 GPIO_ACTIVE_LOW>, + <&mcp23s18 1 GPIO_ACTIVE_LOW>, + <&mcp23s18 2 GPIO_ACTIVE_LOW>, + <&mcp23s18 3 GPIO_ACTIVE_LOW>, + <&mcp23s18 4 GPIO_ACTIVE_LOW>, + <&mcp23s18 5 GPIO_ACTIVE_LOW>, + <&mcp23s18 6 GPIO_ACTIVE_LOW>, + <&mcp23s18 7 GPIO_ACTIVE_LOW>; + }; + + seven-segment-right { + compatible = "gpio-7-segment"; + segment-gpios = <&mcp23s18 8 GPIO_ACTIVE_LOW>, + <&mcp23s18 9 GPIO_ACTIVE_LOW>, + <&mcp23s18 10 GPIO_ACTIVE_LOW>, + <&mcp23s18 11 GPIO_ACTIVE_LOW>, + <&mcp23s18 12 GPIO_ACTIVE_LOW>, + <&mcp23s18 13 GPIO_ACTIVE_LOW>, + <&mcp23s18 14 GPIO_ACTIVE_LOW>, + <&mcp23s18 15 GPIO_ACTIVE_LOW>; + }; + + pwm-beeper { + compatible = "pwm-beeper"; + pwms = <&epwm0 1 1000000 0>; + amp-supply = <&sensor_3v3>; + pinctrl-names = "default"; + pinctrl-0 = <&pwm_beeper_default_pins>; + }; + + vsys_out: regulator-0 { + /* output of BQ24070 */ + compatible = "regulator-fixed"; + regulator-name = "VSYS_OUT"; + regulator-min-microvolt = <4400000>; + regulator-max-microvolt = <4400000>; + regulator-always-on; + regulator-boot-on; + bootph-all; + }; + + vcc_3v3_main: regulator-1 { + /* output of TPS62A06 */ + compatible = "regulator-fixed"; + regulator-name = "VCC_3V3_MAIN"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vsys_out>; + regulator-always-on; + regulator-boot-on; + bootph-all; + }; + + vdd_3v3: regulator-2 { + /* output of TPS22965 */ + compatible = "regulator-fixed"; + regulator-name = "VDD_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vsys_out>; + regulator-always-on; + regulator-boot-on; + bootph-all; + }; + + vdd_3v3_sd: regulator-3 { + /* TPS22918DBVR */ + compatible = "regulator-fixed"; + regulator-name = "VDD_3V3_SD"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vdd_3v3>; + regulator-boot-on; + enable-active-high; + gpio = <&gpio0 16 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&vdd_3v3_sd_ena_default_pins>; + bootph-all; + }; + + sensor_3v3: regulator-4 { + /* TPS22918DBVR */ + compatible = "regulator-fixed"; + regulator-name = "Sensor_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vdd_3v3>; + regulator-boot-on; + regulator-always-on; + enable-active-high; + gpio = <&wkup_gpio0 1 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&sensor_3v3_ena_default_pins>; + bootph-all; + }; + + wlan_en: regulator-5 { + compatible = "regulator-fixed"; + regulator-name = "wlan_en"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + enable-active-high; + gpios = <&gpio0 51 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&wlan_en_pins_default>; + }; +}; + +&pmx0 { + uart0_default_pins: uart0-default-pins { + pinctrl-single,pins = < + AM62LX_IOPAD(0x01b8, PIN_OUTPUT, 0) /* (C13) UART0_TXD */ + AM62LX_IOPAD(0x01b4, PIN_INPUT, 0) /* (D13) UART0_RXD */ + >; + bootph-all; + }; + + uart0_wakeup_pins: uart0-wakeup-pins { + pinctrl-single,pins = < + AM62LX_IOPAD(0x01b8, PIN_OUTPUT, 0) /* (C13) UART0_TXD */ + AM62LX_IOPAD(0x01b4, PIN_INPUT | PIN_WKUP_EN, 0) /* (D13) UART0_RXD */ + >; + bootph-all; + }; + + uart1_default_pins: uart1-default-pins { + pinctrl-single,pins = < + AM62LX_IOPAD(0x019c, PIN_OUTPUT, 2) /* (A12) UART1_TXD */ + AM62LX_IOPAD(0x0198, PIN_INPUT, 2) /* (C11) UART1_RXD */ + AM62LX_IOPAD(0x0180, PIN_INPUT, 2) /* (A8) UART1_CTS */ + AM62LX_IOPAD(0x0184, PIN_OUTPUT, 2) /* (B10) UART1_RTS */ + >; + bootph-all; + }; + + usr_button_default_pins: usr-button-default-pins { + pinctrl-single,pins = < + AM62LX_IOPAD(0x00a4, PIN_INPUT, 7) /* (H18) GPMC0_AD11.GPIO0_26 */ + AM62LX_IOPAD(0x01e4, PIN_INPUT, 7) /* (D16) EXT_REFCLK1.GPIO0_104 */ + AM62LX_IOPAD(0x00c0, PIN_INPUT, 7) /* (N19) GPMC0_ADVn_ALE.GPIO0_32 */ + AM62LX_IOPAD(0x00e8, PIN_INPUT, 7) /* (L19) GPMC0_CSn1.GPIO0_42 */ + AM62LX_IOPAD(0x00b8, PIN_INPUT, 7) /* (L21) GPMC0_CLK.GPIO0_31 */ + AM62LX_IOPAD(0x01c0, PIN_INPUT, 7) /* (B13) UART0_RTSn.GPIO0_95 */ + >; + }; + + i2c0_default_pins: i2c0-default-pins { + pinctrl-single,pins = < + AM62LX_IOPAD(0x01cc, PIN_INPUT_PULLUP, 0) /* (B7) I2C0_SCL */ + AM62LX_IOPAD(0x01d0, PIN_INPUT_PULLUP, 0) /* (A7) I2C0_SDA */ + >; + bootph-all; + }; + + i2c1_default_pins: i2c1-default-pins { + pinctrl-single,pins = < + AM62LX_IOPAD(0x01d4, PIN_INPUT_PULLUP, 0) /* (D7) I2C1_SCL */ + AM62LX_IOPAD(0x01d8, PIN_INPUT_PULLUP, 0) /* (A6) I2C1_SDA */ + >; + bootph-all; + }; + + vdd_3v3_sd_ena_default_pins: vdd-3v3-sd-ena-default-pins { + pinctrl-single,pins = < + AM62LX_IOPAD(0x07c, PIN_OUTPUT, 7) /* (L23) GPMC0_AD1.GPIO0_16 */ + >; + bootph-all; + }; + + sensor_3v3_ena_default_pins: sensor-3v3-ena-default-pins { + pinctrl-single,pins = < + AM62LX_IOPAD(0x004, PIN_OUTPUT, 7) /* (AA23) WKUP_UART0_TXD.WKUP_GPIO0_1 */ + >; + }; + + mmc1_default_pins: mmc1-default-pins { + pinctrl-single,pins = < + AM62LX_IOPAD(0x0230, PIN_INPUT, 0) /* (Y3) MMC1_CMD */ + AM62LX_IOPAD(0x0228, PIN_OUTPUT, 0) /* (Y2) MMC1_CLK */ + AM62LX_IOPAD(0x0224, PIN_INPUT, 0) /* (AA1) MMC1_DAT0 */ + AM62LX_IOPAD(0x0220, PIN_INPUT, 0) /* (Y4) MMC1_DAT1 */ + AM62LX_IOPAD(0x021c, PIN_INPUT, 0) /* (AA2) MMC1_DAT2 */ + AM62LX_IOPAD(0x0218, PIN_INPUT, 0) /* (AB2) MMC1_DAT3 */ + AM62LX_IOPAD(0x0234, PIN_INPUT, 0) /* (B6) MMC1_SDCD */ + >; + bootph-all; + }; + + mmc2_pins_default: mmc2-default-pins { + pinctrl-single,pins = < + AM62LX_IOPAD(0x010c, PIN_INPUT, 0) /* (U23) MMC2_CMD */ + AM62LX_IOPAD(0x0104, PIN_OUTPUT, 0) /* (R23) MMC2_CLK */ + AM62LX_IOPAD(0x0108, PIN_INPUT, 0) /* () MMC2_CLKLB */ + AM62LX_IOPAD(0x0100, PIN_INPUT, 0) /* (U22) MMC2_DAT0 */ + AM62LX_IOPAD(0x00fc, PIN_INPUT, 0) /* (T22) MMC2_DAT1 */ + AM62LX_IOPAD(0x00f8, PIN_INPUT, 0) /* (T23) MMC2_DAT2 */ + AM62LX_IOPAD(0x00f4, PIN_INPUT, 0) /* (R22) MMC2_DAT3 */ + >; + }; + + wlan_en_pins_default: wlan-en-pins-default { + pinctrl-single,pins = < + AM62LX_IOPAD(0x0110, PIN_OUTPUT, 7) /* (T20) MMC2_SDCD.GPIO0_51 */ + >; + }; + + wlirq_pins_default: wlirq-pins-default { + pinctrl-single,pins = < + AM62LX_IOPAD(0x0114, PIN_INPUT, 7) /* (T21) MMC2_SDWP.GPIO0_52 */ + >; + }; + + usb1_default_pins: usb1-default-pins { + pinctrl-single,pins = < + AM62LX_IOPAD(0x0248, PIN_INPUT | PIN_DS_PULLUD_ENABLE | PIN_DS_PULL_UP, 0) /* (A5) USB1_DRVVBUS */ + >; + bootph-all; + }; + + pwm_beeper_default_pins: pwm-beeper-default-pins { + pinctrl-single,pins = < + AM62LX_IOPAD(0x00b0, PIN_OUTPUT, 4) /* (F22) GPMC0_AD14.EHRPWM0_B */ + >; + }; + + pmic_irq_default_pins: pmic-irq-default-pins { + pinctrl-single,pins = < + AM62LX_IOPAD(0x01e8, PIN_INPUT, 0) /* (C8) EXTINTn */ + >; + bootph-all; + }; + + wkup_i2c0_default_pins: wkup-i2c0-default-pins { + pinctrl-single,pins = < + AM62LX_IOPAD(0x0010, PIN_INPUT_PULLUP, 0) /* (AB22) WKUP_I2C0_SCL */ + AM62LX_IOPAD(0x0014, PIN_INPUT_PULLUP, 0) /* (AA22) WKUP_I2C0_SDA */ + >; + bootph-all; + }; + + rgb_led_default_pins: rgb-led-default-pins { + pinctrl-single,pins = < + AM62LX_IOPAD(0x0190, PIN_OUTPUT, 2) /* (A11) MCASP0_ACLKX.ECAP2_IN_APWM_OUT */ + AM62LX_IOPAD(0x0188, PIN_OUTPUT, 2) /* (A9) MCASP0_AXR1.ECAP1_IN_APWM_OUT */ + AM62LX_IOPAD(0x018c, PIN_OUTPUT, 5) /* (B9) MCASP0_AXR0.EHRPWM1_B */ + >; + }; + + spi1_pins_default: spi1-default-pins { + pinctrl-single,pins = < + AM62LX_IOPAD(0x008c, PIN_OUTPUT, 4) /* (H22) GPMC0_AD5.SPI1_CLK */ + AM62LX_IOPAD(0x0088, PIN_OUTPUT, 4) /* (K23) GPMC0_AD4.SPI1_CS0 */ + AM62LX_IOPAD(0x0080, PIN_INPUT, 4) /* (K22) GPMC0_AD2.SPI1_D0 */ + AM62LX_IOPAD(0x0084, PIN_OUTPUT, 4) /* (J23) GPMC0_AD3.SPI1_D1 */ + >; + bootph-all; + }; + + spi3_pins_default: spi3-default-pins { + pinctrl-single,pins = < + AM62LX_IOPAD(0x00d0, PIN_OUTPUT, 5) /* (P22) GPMC0_BE1n.SPI3_CLK */ + AM62LX_IOPAD(0x00cc, PIN_OUTPUT, 5) /* (P23) GPMC0_BE0n_CLE.SPI3_CS0 */ + AM62LX_IOPAD(0x00d4, PIN_INPUT, 5) /* (N23) GPMC0_WAIT0.SPI3_D0 */ + AM62LX_IOPAD(0x00d8, PIN_OUTPUT, 5) /* (N22) GPMC0_WAIT1.SPI3_D1 */ + >; + }; + + mcp23s18_reset_pins_default: mcp23s18-reset-default-pins { + pinctrl-single,pins = < + AM62LX_IOPAD(0x00a0, PIN_OUTPUT, 4) /* (H21) GPMC0_AD10.GPIO0_25 */ + >; + }; + + lora_control_pins_default: lora-control-default-pins { + pinctrl-single,pins = < + AM62LX_IOPAD(0x00c8, PIN_OUTPUT, 7) /* (M19) GPMC0_WEn.GPIO0_34 */ + AM62LX_IOPAD(0x00e4, PIN_OUTPUT, 7) /* (L20) GPMC0_CSn0.GPIO0_41 */ + AM62LX_IOPAD(0x01a4, PIN_INPUT, 7) /* (D11) SPI0_CS1.GPIO0_88 */ + AM62LX_IOPAD(0x01bc, PIN_INPUT, 7) /* (B14) UART0_CTSn.GPIO0_94 */ + >; + }; +}; + +&uart0 { + wakeup-source; + pinctrl-0 = <&uart0_default_pins>; + pinctrl-1 = <&uart0_wakeup_pins>; + pinctrl-names = "default", "wakeup"; + bootph-all; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_default_pins>; + bootph-all; + status = "okay"; +}; + +&i2c0 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_default_pins>; + bootph-all; + status = "okay"; + + /* EEPROM */ + eeprom@50 { + /* FT24C32A-ELRT */ + compatible = "atmel,24c32"; + reg = <0x50>; + }; + + /* Fuel Gauge */ + fuel-gauge@55 { + compatible = "ti,bq27541"; + reg = <0x55>; + }; + + /* IMU Sensor */ + accelerometer@6a { + compatible = "st,lsm6ds3tr-c"; + reg = <0x6a>; + vdd-supply = <&vcc_3v3_main>; + vddio-supply = <&vcc_3v3_main>; + }; + + /* T&H Sensor */ + th-sensor@44 { + compatible = "sensirion,sht4x"; + reg = <0x44>; + }; +}; + +&i2c1 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_default_pins>; + bootph-all; + status = "okay"; +}; + +&wkup_i2c0 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&wkup_i2c0_default_pins>; + status = "okay"; + + tps65214: pmic@30 { + compatible = "ti,tps65214"; + reg = <0x30>; + interrupt-parent = <&gic500>; + interrupts = <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>; + buck1-supply = <&vcc_3v3_main>; + buck2-supply = <&vcc_3v3_main>; + buck3-supply = <&vcc_3v3_main>; + ldo1-supply = <&vcc_3v3_main>; + ldo2-supply = <&vcc_3v3_main>; + pinctrl-names = "default"; + pinctrl-0 = <&pmic_irq_default_pins>; + ti,power-button; + + regulators { + buck1_reg: buck1 { + regulator-name = "VDD_CORE"; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <750000>; + regulator-always-on; + regulator-boot-on; + }; + + buck2_reg: buck2 { + regulator-name = "VDD_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + buck3_reg: buck3 { + regulator-name = "VDD_LPDDR4"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo1_reg: ldo1 { + regulator-name = "VDDA_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo2_reg: ldo2 { + regulator-name = "PMIC_VDD_RTC"; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <750000>; + regulator-always-on; + regulator-boot-on; + }; + }; + }; +}; + +&gpio0 { + gpio-line-names ="","","","","","","","","","", /* 0-9 */ + "","","","","","","VDD_3V3_SD_ENA","","","", /* 10-19 */ + "","","","","","MCP23S18_RESET","USR0","","","", /* 20-29 */ + "","USR1","USR2","","LORA_RESET","","","","","", /* 30-39 */ + "","LORA_RFSW","USR3","","","","","","","", /* 40-49 */ + "","VDD_WLAN_EN","WL_IRQ","","","","","","","", /* 50-59 */ + "","","","","","","","","","", /* 60-69 */ + "","","","","","","","","","", /* 70-79 */ + "","","","","","","","","LORA_BUSY","", /* 80-89 */ + "","","","","LORA_DIO","USR4","","","","", /* 90-99 */ + "","","","","USR5","","","","",""; /* 100-109 */ + pinctrl-names = "default"; + pinctrl-0 = <&lora_control_pins_default>; + bootph-all; + status = "okay"; +}; + +&gpio2 { + bootph-all; + status = "okay"; +}; + +&wkup_gpio0 { + gpio-line-names ="","SENSOR_3V3_ENA","","","","","",""; /* 0-7 */ + bootph-all; + status = "okay"; +}; + +&sdhci1 { + /* SD/MMC */ + vmmc-supply = <&vdd_3v3_sd>; + disable-wp; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_default_pins>; + bootph-all; + status = "okay"; +}; + +&sdhci2 { + vmmc-supply = <&wlan_en>; + bus-width = <4>; + non-removable; + cap-power-off-card; + keep-power-in-suspend; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins_default>; + ti,driver-strength-ohm = <50>; + ti,fails-without-test-cd; + status = "okay"; + + wlcore: wlcore@2 { + compatible = "ti,cc3300"; + reg = <2>; + interrupt-parent = <&gpio0>; + interrupts = <52 IRQ_TYPE_EDGE_RISING>; + pinctrl-names = "default"; + pinctrl-0 = <&wlirq_pins_default>; + }; +}; + +&epwm0 { + status = "okay"; +};
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts line 598
Quoted 10 lines
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts new file +10
-0+ +&epwm1 { + status = "okay"; +}; + +&ecap1 { + status = "okay"; +}; + +&ecap2 {
No pinmux here? Even if you are using the default muxing, you should still add the pinmux info for both completness and to prevent accidental pin reuse by some future addition. Same for EPWM above and USB nodes below.
Andrew
Quoted 57 lines
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts new file +57
-0+ status = "okay"; +}; + +&usbss0 { + ti,vbus-divider; + status = "okay"; +}; + +&usb0 { + usb-role-switch; + bootph-all; + status = "okay"; +}; + +&usbss1 { + ti,vbus-divider; + bootph-all; + status = "okay"; +}; + +&usb1 { + dr_mode = "host"; + pinctrl-names = "default"; + pinctrl-0 = <&usb1_default_pins>; + bootph-all; + status = "okay"; +}; + +&spi1 { + pinctrl-names = "default"; + pinctrl-0 = <&spi1_pins_default>; + status = "okay"; + + mcp23s18: gpio@0 { + compatible = "microchip,mcp23s18"; + reg = <0>; + spi-max-frequency = <10000000>; + gpio-controller; + #gpio-cells = <2>; + reset-gpios = <&gpio0 25 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&mcp23s18_reset_pins_default>; + microchip,spi-present-mask = <0x01>; + }; +}; + +&spi3 { + pinctrl-names = "default"; + pinctrl-0 = <&spi3_pins_default>; + status = "okay"; + + sx1262_lora: lora@0 { + compatible = "rohm,dh2228fv"; + reg = <0>; + spi-max-frequency = <10000000>; + }; +};
Re: [PATCH 2/2] arm64: dts: ti: Add k3-am62l3-beaglebadge
Hi Andrew,
Quoted 672 lines · Andrew Davis
Quoted 671 lines · Judith Mendez
BeagleBoard.org BeagleBadge is a compact, affordable open source hardware single board computer based on the Texas Instruments AM62L3 SoC designed for IoT and embedded applications with low power consumption. Expansion is provided over open standards based headers including QWIIC and GPIO interfaces.
https://beagleboard.org/
https://github.com/beagleboard/BeagleBadgeCo-developed-by Andrew Davis <[email protected]>Signed-off-by Judith Mendez <[email protected]>---
arch/arm64/boot/dts/ti/Makefile | 1 +arch/arm64/boot/dts/ti/k3-am62l3-badge.dts| 655 +++++++++++++++++++++2 files changed, 656 insertions(+)create mode 100644
arch/arm64/boot/dts/ti/k3-am62l3-badge.dtsarch/arm64/boot/dts/ti/Makefile +0
-0@@ -41,6 +41,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-am62d2-evm.dtb # Boards with AM62Lx SoCsdtb-$(CONFIG_ARCH_K3) += k3-am62l3-evm.dtb
+dtb-$(CONFIG_ARCH_K3) += k3-am62l3-badge.dtb
# Boards with AM62Px SoC
dtb-$(CONFIG_ARCH_K3) += k3-am62p5-sk.dtbarch/arm64/boot/dts/ti/k3-am62l3-badge.dts new file +5
-0@@ -0,0 +1,655 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * https://www.beagleboard.org/boards/beaglebadge + * + * Copyright (C) 2026 Texas Instruments Incorporated - https://www.ti.com/
+ */arch/arm64/boot/dts/ti/k3-am62l3-badge.dts new file +231
-0+ +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/net/ti-dp83867.h> +#include "k3-am62l3.dtsi" +#include "k3-pinctrl.h" + +/ { + compatible = "beagle,am62l3-badge", "ti,am62l3"; + model = "BeagleBoard.org BeagleBadge"; + + chosen { + stdout-path = &uart0; + }; + + aliases { + gpio0 = &gpio0; + gpio1 = &gpio2; + gpio2 = &wkup_gpio0; + i2c0 = &i2c0; + i2c1 = &i2c1; + i2c4 = &wkup_i2c0; + mmc1 = &sdhci1; + mmc2 = &sdhci2; + serial3 = &uart1; + usb0 = &usb0; + usb1 = &usb1; + }; + + memory@80000000 { + /* 256MB */ + reg = <0x00000000 0x80000000 0x00000000 0x10000000>; + device_type = "memory"; + bootph-all; + }; + + gpio_keys: gpio-keys { + compatible = "gpio-keys"; + autorepeat; + pinctrl-names = "default"; + pinctrl-0 = <&usr_button_default_pins>; + + button-select { + label = "SELECT"; + linux,code = <KEY_SELECT>; + gpios = <&gpio0 26 GPIO_ACTIVE_LOW>; + }; + + button-back { + label = "BACK"; + linux,code = <KEY_BACK>; + gpios = <&gpio0 104 GPIO_ACTIVE_LOW>; + }; + + button-up { + label = "UP"; + linux,code = <KEY_UP>; + gpios = <&gpio0 32 GPIO_ACTIVE_LOW>; + }; + + button-down { + label = "DOWN"; + linux,code = <KEY_DOWN>; + gpios = <&gpio0 42 GPIO_ACTIVE_LOW>; + }; + + button-left { + label = "LEFT"; + linux,code = <KEY_LEFT>; + gpios = <&gpio0 31 GPIO_ACTIVE_LOW>; + }; + + button-right { + label = "RIGHT"; + linux,code = <KEY_RIGHT>; + gpios = <&gpio0 95 GPIO_ACTIVE_LOW>; + }; + }; + + multicolor-led { + compatible = "pwm-leds-multicolor"; + pinctrl-names = "default"; + pinctrl-0 = <&rgb_led_default_pins>; + + multi-led { + color = <LED_COLOR_ID_RGB>; + max-brightness = <255>; + + led-red { + pwms = <&ecap2 0 255 0>; + color = <LED_COLOR_ID_RED>; + }; + + led-green { + pwms = <&ecap1 0 255 0>; + color = <LED_COLOR_ID_GREEN>; + }; + + led-blue { + pwms = <&epwm1 1 255 0>; + color = <LED_COLOR_ID_BLUE>; + }; + }; + }; + + seven-segment-left { + compatible = "gpio-7-segment"; + segment-gpios = <&mcp23s18 0 GPIO_ACTIVE_LOW>, + <&mcp23s18 1 GPIO_ACTIVE_LOW>, + <&mcp23s18 2 GPIO_ACTIVE_LOW>, + <&mcp23s18 3 GPIO_ACTIVE_LOW>, + <&mcp23s18 4 GPIO_ACTIVE_LOW>, + <&mcp23s18 5 GPIO_ACTIVE_LOW>, + <&mcp23s18 6 GPIO_ACTIVE_LOW>, + <&mcp23s18 7 GPIO_ACTIVE_LOW>; + }; + + seven-segment-right { + compatible = "gpio-7-segment"; + segment-gpios = <&mcp23s18 8 GPIO_ACTIVE_LOW>, + <&mcp23s18 9 GPIO_ACTIVE_LOW>, + <&mcp23s18 10 GPIO_ACTIVE_LOW>, + <&mcp23s18 11 GPIO_ACTIVE_LOW>, + <&mcp23s18 12 GPIO_ACTIVE_LOW>, + <&mcp23s18 13 GPIO_ACTIVE_LOW>, + <&mcp23s18 14 GPIO_ACTIVE_LOW>, + <&mcp23s18 15 GPIO_ACTIVE_LOW>; + }; + + pwm-beeper { + compatible = "pwm-beeper"; + pwms = <&epwm0 1 1000000 0>; + amp-supply = <&sensor_3v3>; + pinctrl-names = "default"; + pinctrl-0 = <&pwm_beeper_default_pins>; + }; + + vsys_out: regulator-0 { + /* output of BQ24070 */ + compatible = "regulator-fixed"; + regulator-name = "VSYS_OUT"; + regulator-min-microvolt = <4400000>; + regulator-max-microvolt = <4400000>; + regulator-always-on; + regulator-boot-on; + bootph-all; + }; + + vcc_3v3_main: regulator-1 { + /* output of TPS62A06 */ + compatible = "regulator-fixed"; + regulator-name = "VCC_3V3_MAIN"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vsys_out>; + regulator-always-on; + regulator-boot-on; + bootph-all; + }; + + vdd_3v3: regulator-2 { + /* output of TPS22965 */ + compatible = "regulator-fixed"; + regulator-name = "VDD_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vsys_out>; + regulator-always-on; + regulator-boot-on; + bootph-all; + }; + + vdd_3v3_sd: regulator-3 { + /* TPS22918DBVR */ + compatible = "regulator-fixed"; + regulator-name = "VDD_3V3_SD"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vdd_3v3>; + regulator-boot-on; + enable-active-high; + gpio = <&gpio0 16 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&vdd_3v3_sd_ena_default_pins>; + bootph-all; + }; + + sensor_3v3: regulator-4 { + /* TPS22918DBVR */ + compatible = "regulator-fixed"; + regulator-name = "Sensor_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vdd_3v3>; + regulator-boot-on; + regulator-always-on; + enable-active-high; + gpio = <&wkup_gpio0 1 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&sensor_3v3_ena_default_pins>; + bootph-all; + }; + + wlan_en: regulator-5 { + compatible = "regulator-fixed"; + regulator-name = "wlan_en"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + enable-active-high; + gpios = <&gpio0 51 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&wlan_en_pins_default>; + }; +}; + +&pmx0 { + uart0_default_pins: uart0-default-pins { + pinctrl-single,pins = < + AM62LX_IOPAD(0x01b8, PIN_OUTPUT, 0) /* (C13) UART0_TXD */ + AM62LX_IOPAD(0x01b4, PIN_INPUT, 0) /* (D13) UART0_RXD */ + >; + bootph-all; + }; + + uart0_wakeup_pins: uart0-wakeup-pins { + pinctrl-single,pins = < + AM62LX_IOPAD(0x01b8, PIN_OUTPUT, 0) /* (C13) UART0_TXD */ + AM62LX_IOPAD(0x01b4, PIN_INPUT | PIN_WKUP_EN, 0) /* (D13)
UART0_RXD*/
+ >;
+ bootph-all;
+ };arch/arm64/boot/dts/ti/k3-am62l3-badge.dts new file +14
-0+ + uart1_default_pins: uart1-default-pins { + pinctrl-single,pins = < + AM62LX_IOPAD(0x019c, PIN_OUTPUT, 2) /* (A12) UART1_TXD */ + AM62LX_IOPAD(0x0198, PIN_INPUT, 2) /* (C11) UART1_RXD */ + AM62LX_IOPAD(0x0180, PIN_INPUT, 2) /* (A8) UART1_CTS */ + AM62LX_IOPAD(0x0184, PIN_OUTPUT, 2) /* (B10) UART1_RTS */ + >; + bootph-all; + }; + + usr_button_default_pins: usr-button-default-pins { + pinctrl-single,pins = < + AM62LX_IOPAD(0x00a4, PIN_INPUT, 7) /* (H18)GPMC0_AD11.GPIO0_26 */
+AM62LX_IOPAD(0x01e4, PIN_INPUT, 7)/* (D16) EXT_REFCLK1.GPIO0_104 */
+AM62LX_IOPAD(0x00c0, PIN_INPUT, 7)/* (N19) GPMC0_ADVn_ALE.GPIO0_32 */
+AM62LX_IOPAD(0x00e8, PIN_INPUT, 7)/* (L19) GPMC0_CSn1.GPIO0_42 */
+AM62LX_IOPAD(0x00b8, PIN_INPUT, 7)/* (L21) GPMC0_CLK.GPIO0_31 */
+AM62LX_IOPAD(0x01c0, PIN_INPUT, 7)/* (B13) UART0_RTSn.GPIO0_95 */
+ >;
+ };
+
+i2c0_default_pins: i2c0-default-pins {
+ pinctrl-single,pins = <
+AM62LX_IOPAD(0x01cc, PIN_INPUT_PULLUP, 0)/* (B7)I2C0_SCL*/
+AM62LX_IOPAD(0x01d0, PIN_INPUT_PULLUP, 0)/* (A7)I2C0_SDA*/
+ >;
+ bootph-all;
+ };
+
+i2c1_default_pins: i2c1-default-pins {
+ pinctrl-single,pins = <
+AM62LX_IOPAD(0x01d4, PIN_INPUT_PULLUP, 0)/* (D7)I2C1_SCL*/
+AM62LX_IOPAD(0x01d8, PIN_INPUT_PULLUP, 0)/* (A6)I2C1_SDA*/
+ >;
+ bootph-all;
+ };
+
+vdd_3v3_sd_ena_default_pins: vdd-3v3-sd-ena-default-pins { + pinctrl-single,pins = <
+AM62LX_IOPAD(0x07c, PIN_OUTPUT, 7)/* (L23) GPMC0_AD1.GPIO0_16 */
+ >;
+ bootph-all;
+ };
+
+sensor_3v3_ena_default_pins: sensor-3v3-ena-default-pins { + pinctrl-single,pins = <
+AM62LX_IOPAD(0x004, PIN_OUTPUT, 7)/* (AA23) WKUP_UART0_TXD.WKUP_GPIO0_1 */
+ >;
+ };arch/arm64/boot/dts/ti/k3-am62l3-badge.dts new file +29
-0+ + mmc1_default_pins: mmc1-default-pins { + pinctrl-single,pins = < + AM62LX_IOPAD(0x0230, PIN_INPUT, 0) /* (Y3) MMC1_CMD */ + AM62LX_IOPAD(0x0228, PIN_OUTPUT, 0) /* (Y2) MMC1_CLK */ + AM62LX_IOPAD(0x0224, PIN_INPUT, 0) /* (AA1) MMC1_DAT0 */ + AM62LX_IOPAD(0x0220, PIN_INPUT, 0) /* (Y4) MMC1_DAT1 */ + AM62LX_IOPAD(0x021c, PIN_INPUT, 0) /* (AA2) MMC1_DAT2 */ + AM62LX_IOPAD(0x0218, PIN_INPUT, 0) /* (AB2) MMC1_DAT3 */ + AM62LX_IOPAD(0x0234, PIN_INPUT, 0) /* (B6) MMC1_SDCD */ + >; + bootph-all; + }; + + mmc2_pins_default: mmc2-default-pins { + pinctrl-single,pins = < + AM62LX_IOPAD(0x010c, PIN_INPUT, 0) /* (U23) MMC2_CMD */ + AM62LX_IOPAD(0x0104, PIN_OUTPUT, 0) /* (R23) MMC2_CLK */ + AM62LX_IOPAD(0x0108, PIN_INPUT, 0) /* () MMC2_CLKLB */ + AM62LX_IOPAD(0x0100, PIN_INPUT, 0) /* (U22) MMC2_DAT0 */ + AM62LX_IOPAD(0x00fc, PIN_INPUT, 0) /* (T22) MMC2_DAT1 */ + AM62LX_IOPAD(0x00f8, PIN_INPUT, 0) /* (T23) MMC2_DAT2 */ + AM62LX_IOPAD(0x00f4, PIN_INPUT, 0) /* (R22) MMC2_DAT3 */ + >; + }; + + wlan_en_pins_default: wlan-en-pins-default { + pinctrl-single,pins = < + AM62LX_IOPAD(0x0110, PIN_OUTPUT, 7) /* (T20)MMC2_SDCD.GPIO0_51 */
+ >;
+ };
+
+wlirq_pins_default: wlirq-pins-default {
+ pinctrl-single,pins = <
+AM62LX_IOPAD(0x0114, PIN_INPUT, 7)/* (T21) MMC2_SDWP.GPIO0_52 */
+ >;
+ };
+
+usb1_default_pins: usb1-default-pins {
+ pinctrl-single,pins = <
+AM62LX_IOPAD(0x0248, PIN_INPUT | PIN_DS_PULLUD_ENABLE | PIN_DS_PULL_UP, 0)/* (A5)USB1_DRVVBUS*/
+ >;
+ bootph-all;
+ };
+
+pwm_beeper_default_pins: pwm-beeper-default-pins {
+ pinctrl-single,pins = <
+AM62LX_IOPAD(0x00b0, PIN_OUTPUT, 4)/* (F22) GPMC0_AD14.EHRPWM0_B */
+ >;
+ };arch/arm64/boot/dts/ti/k3-am62l3-badge.dts new file +11
-0+ + pmic_irq_default_pins: pmic-irq-default-pins { + pinctrl-single,pins = < + AM62LX_IOPAD(0x01e8, PIN_INPUT, 0) /* (C8) EXTINTn */ + >; + bootph-all; + }; + + wkup_i2c0_default_pins: wkup-i2c0-default-pins { + pinctrl-single,pins = < + AM62LX_IOPAD(0x0010, PIN_INPUT_PULLUP, 0) /* (AB22)
WKUP_I2C0_SCL*/
+AM62LX_IOPAD(0x0014, PIN_INPUT_PULLUP, 0)/* (AA22)WKUP_I2C0_SDA*/
+ >;
+ bootph-all;
+ };
+
+rgb_led_default_pins: rgb-led-default-pins {
+ pinctrl-single,pins = <
+AM62LX_IOPAD(0x0190, PIN_OUTPUT, 2)/* (A11) MCASP0_ACLKX.ECAP2_IN_APWM_OUT */
+AM62LX_IOPAD(0x0188, PIN_OUTPUT, 2)/* (A9) MCASP0_AXR1.ECAP1_IN_APWM_OUT */
+AM62LX_IOPAD(0x018c, PIN_OUTPUT, 5)/* (B9) MCASP0_AXR0.EHRPWM1_B */
+ >;
+ };
+
+spi1_pins_default: spi1-default-pins {
+ pinctrl-single,pins = <
+AM62LX_IOPAD(0x008c, PIN_OUTPUT, 4)/* (H22) GPMC0_AD5.SPI1_CLK */
+AM62LX_IOPAD(0x0088, PIN_OUTPUT, 4)/* (K23) GPMC0_AD4.SPI1_CS0 */
+AM62LX_IOPAD(0x0080, PIN_INPUT, 4)/* (K22) GPMC0_AD2.SPI1_D0 */
+AM62LX_IOPAD(0x0084, PIN_OUTPUT, 4)/* (J23) GPMC0_AD3.SPI1_D1 */
+ >;
+ bootph-all;
+ };
+
+spi3_pins_default: spi3-default-pins {
+ pinctrl-single,pins = <
+AM62LX_IOPAD(0x00d0, PIN_OUTPUT, 5)/* (P22) GPMC0_BE1n.SPI3_CLK */
+AM62LX_IOPAD(0x00cc, PIN_OUTPUT, 5)/* (P23) GPMC0_BE0n_CLE.SPI3_CS0 */
+AM62LX_IOPAD(0x00d4, PIN_INPUT, 5)/* (N23) GPMC0_WAIT0.SPI3_D0 */
+AM62LX_IOPAD(0x00d8, PIN_OUTPUT, 5)/* (N22) GPMC0_WAIT1.SPI3_D1 */
+ >;
+ };
+
+mcp23s18_reset_pins_default: mcp23s18-reset-default-pins { + pinctrl-single,pins = <
+AM62LX_IOPAD(0x00a0, PIN_OUTPUT, 4)/* (H21) GPMC0_AD10.GPIO0_25 */
+ >;
+ };
+
+lora_control_pins_default: lora-control-default-pins { + pinctrl-single,pins = <
+AM62LX_IOPAD(0x00c8, PIN_OUTPUT, 7)/* (M19) GPMC0_WEn.GPIO0_34 */
+AM62LX_IOPAD(0x00e4, PIN_OUTPUT, 7)/* (L20) GPMC0_CSn0.GPIO0_41 */
+AM62LX_IOPAD(0x01a4, PIN_INPUT, 7)/* (D11) SPI0_CS1.GPIO0_88 */
+AM62LX_IOPAD(0x01bc, PIN_INPUT, 7)/* (B14) UART0_CTSn.GPIO0_94 */
+ >;
+ };arch/arm64/boot/dts/ti/k3-am62l3-badge.dts new file +127
-0+}; + +&uart0 { + wakeup-source; + pinctrl-0 = <&uart0_default_pins>; + pinctrl-1 = <&uart0_wakeup_pins>; + pinctrl-names = "default", "wakeup"; + bootph-all; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_default_pins>; + bootph-all; + status = "okay"; +}; + +&i2c0 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_default_pins>; + bootph-all; + status = "okay"; + + /* EEPROM */ + eeprom@50 { + /* FT24C32A-ELRT */ + compatible = "atmel,24c32"; + reg = <0x50>; + }; + + /* Fuel Gauge */ + fuel-gauge@55 { + compatible = "ti,bq27541"; + reg = <0x55>; + }; + + /* IMU Sensor */ + accelerometer@6a { + compatible = "st,lsm6ds3tr-c"; + reg = <0x6a>; + vdd-supply = <&vcc_3v3_main>; + vddio-supply = <&vcc_3v3_main>; + }; + + /* T&H Sensor */ + th-sensor@44 { + compatible = "sensirion,sht4x"; + reg = <0x44>; + }; +}; + +&i2c1 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_default_pins>; + bootph-all; + status = "okay"; +}; + +&wkup_i2c0 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&wkup_i2c0_default_pins>; + status = "okay"; + + tps65214: pmic@30 { + compatible = "ti,tps65214"; + reg = <0x30>; + interrupt-parent = <&gic500>; + interrupts = <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>; + buck1-supply = <&vcc_3v3_main>; + buck2-supply = <&vcc_3v3_main>; + buck3-supply = <&vcc_3v3_main>; + ldo1-supply = <&vcc_3v3_main>; + ldo2-supply = <&vcc_3v3_main>; + pinctrl-names = "default"; + pinctrl-0 = <&pmic_irq_default_pins>; + ti,power-button; + + regulators { + buck1_reg: buck1 { + regulator-name = "VDD_CORE"; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <750000>; + regulator-always-on; + regulator-boot-on; + }; + + buck2_reg: buck2 { + regulator-name = "VDD_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + buck3_reg: buck3 { + regulator-name = "VDD_LPDDR4"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo1_reg: ldo1 { + regulator-name = "VDDA_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo2_reg: ldo2 { + regulator-name = "PMIC_VDD_RTC"; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <750000>; + regulator-always-on; + regulator-boot-on; + }; + }; + }; +}; + +&gpio0 { + gpio-line-names ="","","","","","","","","","", /*0-9 */
+ "","","","","","","VDD_3V3_SD_ENA","","","", /* 10-19 */
+ "","","","","","MCP23S18_RESET","USR0","","","", /* 20-29 */
+ "","USR1","USR2","","LORA_RESET","","","","","", /* 30-39 */
+ "","LORA_RFSW","USR3","","","","","","","", /* 40-49 */
+ "","VDD_WLAN_EN","WL_IRQ","","","","","","","", /* 50-59 */
+ "","","","","","","","","","", /* 60-69 */ + "","","","","","","","","","", /* 70-79 */ + "","","","","","","","","LORA_BUSY","", /* 80-89 */ + "","","","","LORA_DIO","USR4","","","","", /* 90-99 */
+ "","","","","USR5","","","","",""; /* 100-109 */ + pinctrl-names = "default";
+ pinctrl-0 = <&lora_control_pins_default>;
+ bootph-all;
+ status = "okay";arch/arm64/boot/dts/ti/k3-am62l3-badge.dts new file +9
-0+}; + +&gpio2 { + bootph-all; + status = "okay"; +}; + +&wkup_gpio0 { + gpio-line-names="","SENSOR_3V3_ENA","","","","","",""; /* 0-7 */ + bootph-all;
+ status = "okay";arch/arm64/boot/dts/ti/k3-am62l3-badge.dts new file +45
-0+}; + +&sdhci1 { + /* SD/MMC */ + vmmc-supply = <&vdd_3v3_sd>; + disable-wp; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_default_pins>; + bootph-all; + status = "okay"; +}; + +&sdhci2 { + vmmc-supply = <&wlan_en>; + bus-width = <4>; + non-removable; + cap-power-off-card; + keep-power-in-suspend; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins_default>; + ti,driver-strength-ohm = <50>; + ti,fails-without-test-cd; + status = "okay"; + + wlcore: wlcore@2 { + compatible = "ti,cc3300"; + reg = <2>; + interrupt-parent = <&gpio0>; + interrupts = <52 IRQ_TYPE_EDGE_RISING>; + pinctrl-names = "default"; + pinctrl-0 = <&wlirq_pins_default>; + }; +}; + +&epwm0 { + status = "okay"; +}; + +&epwm1 { + status = "okay"; +}; + +&ecap1 {
Quoted 8 lines
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts line 598
Quoted 4 lines
+ status = "okay";
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts new file +3
-0+}; + +&ecap2 {No pinmux here? Even if you are using the default muxing, you should still add the pinmux info for both completness and to prevent accidental pin reuse by some future addition. Same for EPWM above and USB nodes below.
Will missing pinmux nodes & respin, thanks.
~ Judith
Quoted 61 lines
Andrew
Quoted 57 lines
+ status = "okay";
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts new file +56
-0+}; + +&usbss0 { + ti,vbus-divider; + status = "okay"; +}; + +&usb0 { + usb-role-switch; + bootph-all; + status = "okay"; +}; + +&usbss1 { + ti,vbus-divider; + bootph-all; + status = "okay"; +}; + +&usb1 { + dr_mode = "host"; + pinctrl-names = "default"; + pinctrl-0 = <&usb1_default_pins>; + bootph-all; + status = "okay"; +}; + +&spi1 { + pinctrl-names = "default"; + pinctrl-0 = <&spi1_pins_default>; + status = "okay"; + + mcp23s18: gpio@0 { + compatible = "microchip,mcp23s18"; + reg = <0>; + spi-max-frequency = <10000000>; + gpio-controller; + #gpio-cells = <2>; + reset-gpios = <&gpio0 25 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&mcp23s18_reset_pins_default>; + microchip,spi-present-mask = <0x01>; + }; +}; + +&spi3 { + pinctrl-names = "default"; + pinctrl-0 = <&spi3_pins_default>; + status = "okay"; + + sx1262_lora: lora@0 { + compatible = "rohm,dh2228fv"; + reg = <0>; + spi-max-frequency = <10000000>; + }; +};
Re: [PATCH 2/2] arm64: dts: ti: Add k3-am62l3-beaglebadge
In reply to Judith MendezOn May 1, 2026 thus sayeth Judith Mendez:
Quoted 14 lines
BeagleBoard.org BeagleBadge is a compact, affordable open source hardware single board computer based on the Texas Instruments AM62L3 SoC designed for IoT and embedded applications with low power consumption. Expansion is provided over open standards based headers including QWIIC and GPIO interfaces.
https://beagleboard.org/
https://github.com/beagleboard/BeagleBadgeCo-developed-by Andrew Davis <[email protected]>Signed-off-by Judith Mendez <[email protected]>--- arch/arm64/boot/dts/ti/Makefile | 1 + arch/arm64/boot/dts/ti/k3-am62l3-badge.dts | 655 +++++++++++++++++++++
...
Quoted 15 lines
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts new file +8
-0@@ -0,0 +1,655 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * https://www.beagleboard.org/boards/beaglebadge + * + * Copyright (C) 2026 Texas Instruments Incorporated - https://www.ti.com/ + */ + +/dts-v1/;
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts line 18
Quoted 10 lines
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts new file +10
-0+ +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/net/ti-dp83867.h> +#include "k3-am62l3.dtsi" +#include "k3-pinctrl.h" + +/ { + compatible = "beagle,am62l3-badge", "ti,am62l3";
I noticed the $subject calls it the k3-am62l3-beaglebadge do we want to name the DT that as well?
Quoted 2 lines
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts new file +2
-0+ model = "BeagleBoard.org BeagleBadge"; +
...
Quoted 6 lines
+&sdhci2 {
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts new file +5
-0+ vmmc-supply = <&wlan_en>; + bus-width = <4>; + non-removable; + cap-power-off-card; + keep-power-in-suspend;
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts line 577
Quoted 10 lines
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts new file +10
-0+ #address-cells = <1>; + #size-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins_default>; + ti,driver-strength-ohm = <50>; + ti,fails-without-test-cd; + status = "okay"; + + wlcore: wlcore@2 { + compatible = "ti,cc3300";
Sadly this only exists on our evil vendor tree :/
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts line 585
Quoted 8 lines
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts new file +8
-0+ reg = <2>; + interrupt-parent = <&gpio0>; + interrupts = <52 IRQ_TYPE_EDGE_RISING>; + pinctrl-names = "default"; + pinctrl-0 = <&wlirq_pins_default>; + }; +}; +
Scanning over the bootlog it looks like the VTM driver is active but we're missing the thermal-zones{} node which is causing it issues.
~Bryan
Re: [PATCH 2/2] arm64: dts: ti: Add k3-am62l3-beaglebadge
Hi Bryan, all,
Quoted 47 lines · Bryan Brattlof
On May 1, 2026 thus sayeth Judith Mendez:
Quoted 14 lines
BeagleBoard.org BeagleBadge is a compact, affordable open source hardware single board computer based on the Texas Instruments AM62L3 SoC designed for IoT and embedded applications with low power consumption. Expansion is provided over open standards based headers including QWIIC and GPIO interfaces.
https://beagleboard.org/
https://github.com/beagleboard/BeagleBadgeCo-developed-by Andrew Davis <[email protected]>Signed-off-by Judith Mendez <[email protected]>--- arch/arm64/boot/dts/ti/Makefile | 1 + arch/arm64/boot/dts/ti/k3-am62l3-badge.dts | 655 +++++++++++++++++++++...
Quoted 15 lines
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts new file +8
-0@@ -0,0 +1,655 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * https://www.beagleboard.org/boards/beaglebadge + * + * Copyright (C) 2026 Texas Instruments Incorporated - https://www.ti.com/ + */ + +/dts-v1/;arch/arm64/boot/dts/ti/k3-am62l3-badge.dts line 18
Quoted 10 lines
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts new file +10
-0+ +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/net/ti-dp83867.h> +#include "k3-am62l3.dtsi" +#include "k3-pinctrl.h" + +/ { + compatible = "beagle,am62l3-badge", "ti,am62l3";I noticed the $subject calls it the k3-am62l3-beaglebadge do we want to name the DT that as well?
Quoted 3 lines
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts line 20
Quoted 2 lines
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts new file +2
-0+ model = "BeagleBoard.org BeagleBadge"; +
So I see other beagle boards have the following:
beagle,am67a-beagley-ai in k3-am67a-beagley-ai.dts beagle,am625-beagleplay in k3-am625-beagleplay.dts beagle,am62-pocketbeagle2 in k3-am62-pocketbeagle2.dts beagle,j721e-beagleboneai64 in k3-j721e-beagleboneai64.dts
so I think we should be using:
beagle,am62l3-beaglebadge in k3-am62l3-beaglebadge.dts
so if it is fine with everyone will update compatible & DT filename accordingly.
Quoted 11 lines
Quoted 11 lines
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts new file +10
-0+&sdhci2 { + vmmc-supply = <&wlan_en>; + bus-width = <4>; + non-removable; + cap-power-off-card; + keep-power-in-suspend; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins_default>;
Quoted 8 lines
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts line 577
Quoted 6 lines
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts new file +6
-0+ ti,driver-strength-ohm = <50>; + ti,fails-without-test-cd; + status = "okay"; + + wlcore: wlcore@2 { + compatible = "ti,cc3300";Sadly this only exists on our evil vendor tree :/
So sure, I saw that the WIFI driver is not in mainline, but I also referenced beagleplay series & it seems like as long as the hardware is described properly, the node can be upstreamed. Please correct me if I am wrong here..
Quoted 12 lines
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts line 585
Quoted 9 lines
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts new file +8
-0+ reg = <2>; + interrupt-parent = <&gpio0>; + interrupts = <52 IRQ_TYPE_EDGE_RISING>; + pinctrl-names = "default"; + pinctrl-0 = <&wlirq_pins_default>; + }; +}; +Scanning over the bootlog it looks like the VTM driver is active but we're missing the thermal-zones{} node which is causing it issues.
Opps, will add. thanks.
~ judith
Re: [PATCH 2/2] arm64: dts: ti: Add k3-am62l3-beaglebadge
Quoted 61 lines · Judith Mendez
Hi Bryan, all,
Quoted 38 lines · Bryan Brattlof
On May 1, 2026 thus sayeth Judith Mendez:
Quoted 14 lines
BeagleBoard.org BeagleBadge is a compact, affordable open source hardware single board computer based on the Texas Instruments AM62L3 SoC designed for IoT and embedded applications with low power consumption. Expansion is provided over open standards based headers including QWIIC and GPIO interfaces.
https://beagleboard.org/
https://github.com/beagleboard/BeagleBadgeCo-developed-by Andrew Davis <[email protected]>Signed-off-by Judith Mendez <[email protected]>---
arch/arm64/boot/dts/ti/Makefile | 1 +arch/arm64/boot/dts/ti/k3-am62l3-badge.dts| 655 +++++++++++++++++++++...
Quoted 20 lines
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts new file +13
-0@@ -0,0 +1,655 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * https://www.beagleboard.org/boards/beaglebadge + * + * Copyright (C) 2026 Texas Instruments Incorporated - https://www.ti.com/ + */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/net/ti-dp83867.h>Quoted 12 lines
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts line 18
Quoted 5 lines
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts new file +5
-0+#include "k3-am62l3.dtsi" +#include "k3-pinctrl.h" + +/ { + compatible = "beagle,am62l3-badge", "ti,am62l3";I noticed the $subject calls it the k3-am62l3-beaglebadge do we want to name the DT that as well?
Quoted 2 lines
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts new file +2
-0+ model = "BeagleBoard.org BeagleBadge"; +So I see other beagle boards have the following:
beagle,am67a-beagley-ai in
k3-am67a-beagley-ai.dtsbeagle,am625-beagleplay ink3-am625-beagleplay.dtsbeagle,am62-pocketbeagle2 ink3-am62-pocketbeagle2.dtsbeagle,j721e-beagleboneai64 ink3-j721e-beagleboneai64.dts
Quoted 7 lines
so I think we should be using:
beagle,am62l3-beaglebadge in
k3-am62l3-beaglebadge.dtsso if it is fine with everyone will update compatible & DT filename accordingly.
Looks correct to me.
Quoted 18 lines
Quoted 18 lines
Quoted 17 lines
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts new file +16
-0+&sdhci2 { + vmmc-supply = <&wlan_en>; + bus-width = <4>; + non-removable; + cap-power-off-card; + keep-power-in-suspend; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins_default>; + ti,driver-strength-ohm = <50>; + ti,fails-without-test-cd; + status = "okay"; + + wlcore: wlcore@2 { + compatible = "ti,cc3300";
Quoted 8 lines
Quoted 1 line
Sadly this only exists on our evil vendor tree :/
So sure, I saw that the WIFI driver is not in mainline, but I also referenced beagleplay series & it seems like as long as the hardware is described properly, the node can be upstreamed. Please correct me if I am wrong here..
Only in some special cases, but in general the driver needs to be upstreamed first. And even in those special cases a DT binding is always needed first. Otherwise how would we know if the node is described properly.
For Beagleplay I only see the CC1352P7 radio in DT upstream, and it has a proper binding[0]. For now drop the CC3300, we can simply add it when the driver gets upstream.
Andrew
[0] Documentation/devicetree/bindings/net/ti,cc1352p7.yaml
Quoted 16 lines
Quoted 12 lines
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts line 585
Quoted 9 lines
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts new file +8
-0+ reg = <2>; + interrupt-parent = <&gpio0>; + interrupts = <52 IRQ_TYPE_EDGE_RISING>; + pinctrl-names = "default"; + pinctrl-0 = <&wlirq_pins_default>; + }; +}; +Scanning over the bootlog it looks like the VTM driver is active but we're missing the thermal-zones{} node which is causing it issues.
Opps, will add. thanks.
~ judith
Re: [PATCH 2/2] arm64: dts: ti: Add k3-am62l3-beaglebadge
Quoted 101 lines · Andrew Davis
Quoted 63 lines · Judith Mendez
Hi Bryan, all,
Quoted 40 lines · Bryan Brattlof
On May 1, 2026 thus sayeth Judith Mendez:
Quoted 15 lines
BeagleBoard.org BeagleBadge is a compact, affordable open source hardware single board computer based on the Texas Instruments AM62L3 SoC designed for IoT and embedded applications with low power consumption. Expansion is provided over open standards based headers including QWIIC and GPIO interfaces.
https://beagleboard.org/
https://github.com/beagleboard/BeagleBadgeCo-developed-by Andrew Davis <[email protected]>Signed-off-by Judith Mendez <[email protected]>---
arch/arm64/boot/dts/ti/Makefile | 1 +arch/arm64/boot/dts/ti/k3-am62l3-badge.dts| 655 +++++++++++++++++
++++...
Quoted 21 lines
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts new file +5
-0@@ -0,0 +1,655 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * https://www.beagleboard.org/boards/beaglebadge + * + * Copyright (C) 2026 Texas Instruments Incorporated - https://www.ti.com/
+ */arch/arm64/boot/dts/ti/k3-am62l3-badge.dts new file +7
-0+ +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/net/ti-dp83867.h>Quoted 12 lines
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts line 18
Quoted 5 lines
arch/arm64/boot/dts/ti/k3-am62l3-badge.dts new file +5
-0+#include "k3-am62l3.dtsi" +#include "k3-pinctrl.h" + +/ { + compatible = "beagle,am62l3-badge", "ti,am62l3";I noticed the $subject calls it the k3-am62l3-beaglebadge do we want to name the DT that as well?
Quoted 2 lines
+ model = "BeagleBoard.org BeagleBadge";
+So I see other beagle boards have the following:
beagle,am67a-beagley-ai in
k3-am67a-beagley-ai.dtsbeagle,am625-beagleplay ink3-am625-beagleplay.dtsbeagle,am62-pocketbeagle2 ink3-am62-pocketbeagle2.dtsbeagle,j721e-beagleboneai64 ink3-j721e-beagleboneai64.dtsQuoted 7 lines
so I think we should be using:
beagle,am62l3-beaglebadge in
k3-am62l3-beaglebadge.dtsso if it is fine with everyone will update compatible & DT filename accordingly.
Looks correct to me.
Quoted 18 lines
Quoted 18 lines
Quoted 17 lines
+&sdhci2 {
+ vmmc-supply = <&wlan_en>;
+ bus-width = <4>;
+ non-removable;
+ cap-power-off-card;
+ keep-power-in-suspend;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_pins_default>;
+ ti,driver-strength-ohm = <50>;
+ ti,fails-without-test-cd;
+ status = "okay";
+
+ wlcore: wlcore@2 {
+ compatible = "ti,cc3300";Quoted 8 lines
Quoted 1 line
Sadly this only exists on our evil vendor tree :/
So sure, I saw that the WIFI driver is not in mainline, but I also referenced beagleplay series & it seems like as long as the hardware is described properly, the node can be upstreamed. Please correct me if I am wrong here..
Quoted 9 lines
Only in some special cases, but in general the driver needs to be upstreamed first. And even in those special cases a DT binding is always needed first. Otherwise how would we know if the node is described properly.
For Beagleplay I only see the CC1352P7 radio in DT upstream, and it has a proper binding[0]. For now drop the CC3300, we can simply add it when the driver gets upstream.
got it, will drop wlcore node, thanks.
~ Judith