Skip to contentSkip to conversation

thermal: mediatek: add another get_temp ops for thermal sensors

PATCH In review Ben Tseng 1 participant 2 messages Aug 20, 2021 – Nov 3, 2021

Subsystems (2)
lore
Share & tools
lore

Ben Tseng

author
#0 lore raw

PATCH v9 1/1 thermal: mediatek: add another get_temp ops for thermal sensors

From: Michael Kao <[email protected]>

Provide thermal zone to read thermal sensor
in the SoC. We can read all the thermal sensors
value in the SoC by the node /sys/class/thermal/

In mtk_thermal_bank_temperature, return -EAGAIN instead of -EACCESS on the first read of sensor that often are bogus values. This can avoid following warning on boot:

thermal thermal_zone6: failed to read out thermal zone (-13)

---

This patchset supports for MT8183 chip to mtk_thermal.c. Add thermal zone of all the thermal sensor in SoC for another get temperatrue. They don't need to thermal throttle. And we bind coolers for thermal zone nodes of cpu_thermal.

Changes in V9:
- Rebase to kernel-v5.14-rc1
- Bind raw_to_mcelsius_v1 or raw_to_mcelsius_v2 to compatible data of struct mtk_thermal_data
- Remove duplicate struct 'mtk_thermal_bank'
- Remove unnecessary if condition check
- Return error if any thermal zone fail to register

Changes in V8:
- Rebase to kernel-v5.13-rc1
- Resend

Changes in v7:
- Fix build error in v6.

Changes in v6:
- Rebase to kernel-5.11-rc1.
- [1/3]
- add interrupts property.
- [2/3]
- add the Tested-by in the commit message.
- [3/3]
- use the mt->conf->msr[id] instead of conf->msr[id] in the _get_sensor_temp and mtk_thermal_bank_temperature.
- remove the redundant space in _get_sensor_temp and mtk_read_sensor_temp.
- change kmalloc to dev_kmalloc in mtk_thermal_probe.

Changes in v5:
- Rebase to kernel-5.9-rc1.
- Revise the title of cover letter.
- Drop "[v4,7/7] thermal: mediatek: use spinlock to protect PTPCORESEL"
- [2/2]
- Add the judgement to the version of raw_to_mcelsius.

Changes in v4:
- Rebase to kernel-5.6-rc1.
- [1/7]
- Squash thermal zone settings in the dtsi from [v3,5/8]
arm64: dts: mt8183: Increase polling frequency for CPU thermal zone.
- Remove the property of interrupts and mediatek,hw-reset-temp.
- [2/7]
- Correct commit message.
- [4/7]
- Change the target temperature to the 80C and change the commit message.
- [6/7]
- Adjust newline alignment.
- Fix the judgement on the return value of registering thermal zone.

Changes in v3:
- Rebase to kernel-5.5-rc1.
- [1/8]
- Update sustainable power of cpu, tzts1~5 and tztsABB.
- [7/8]
- Bypass the failure that non cpu_thermal sensor is not find in thermal-zones in dts, which is normal for mt8173, so prompt a warning here instead of failing.

Return -EAGAIN instead of -EACCESS on the first read of sensor that often are bogus values. This can avoid following warning on boot:

thermal thermal_zone6: failed to read out thermal zone (-13)

Changes in v2:
- [1/8]
- Add the sustainable-power,trips,cooling-maps to the tzts1~tztsABB.
- [4/8]
- Add the min opp of cpu throttle.

Matthias Kaehlcke (1):
arm64: dts: mt8183: Configure CPU cooling

Michael Kao (2):
thermal: mediatek: add another get_temp ops for thermal sensors
arm64: dts: mt8183: add thermal zone node

---
 drivers/thermal/mtk_thermal.c | 95 +++++++++++++++++++++++++++++++------------
 1 file changed, 70 insertions(+), 25 deletions(-)
drivers/thermal/mtk_thermal.c +70 -25
index ede94ea..8bb0bb2 100644
@@ -271,6 +271,7 @@ struct mtk_thermal_data {
 	bool need_switch_bank;
 	struct thermal_bank_cfg bank_data[MAX_NUM_ZONES];
 	enum mtk_thermal_version version;
+	int (*raw_to_mcelsius)(struct mtk_thermal *mt, int sensno, s32 raw);
 };
 
 struct mtk_thermal {
@@ -294,6 +295,9 @@ struct mtk_thermal {
 	struct mtk_thermal_bank banks[MAX_NUM_ZONES];
 };
 
+static int raw_to_mcelsius_v1(struct mtk_thermal *mt, int sensno, s32 raw);
+static int raw_to_mcelsius_v2(struct mtk_thermal *mt, int sensno, s32 raw);
+
 /* MT8183 thermal sensor data */
 static const int mt8183_bank_data[MT8183_NUM_SENSORS] = {
 	MT8183_TS1, MT8183_TS2, MT8183_TS3, MT8183_TS4, MT8183_TS5, MT8183_TSABB
@@ -427,6 +431,7 @@ struct mtk_thermal {
 	.adcpnp = mt8173_adcpnp,
 	.sensor_mux_values = mt8173_mux_values,
 	.version = MTK_THERMAL_V1,
+	.raw_to_mcelsius = raw_to_mcelsius_v1,
 };
 
 /*
@@ -458,6 +463,7 @@ struct mtk_thermal {
 	.adcpnp = mt2701_adcpnp,
 	.sensor_mux_values = mt2701_mux_values,
 	.version = MTK_THERMAL_V1,
+	.raw_to_mcelsius = raw_to_mcelsius_v1,
 };
 
 /*
@@ -489,6 +495,7 @@ struct mtk_thermal {
 	.adcpnp = mt2712_adcpnp,
 	.sensor_mux_values = mt2712_mux_values,
 	.version = MTK_THERMAL_V1,
+	.raw_to_mcelsius = raw_to_mcelsius_v1,
 };
 
 /*
@@ -514,6 +521,7 @@ struct mtk_thermal {
 	.adcpnp = mt7622_adcpnp,
 	.sensor_mux_values = mt7622_mux_values,
 	.version = MTK_THERMAL_V2,
+	.raw_to_mcelsius = raw_to_mcelsius_v2,
 };
 
 /*
@@ -547,6 +555,7 @@ struct mtk_thermal {
 	.adcpnp = mt8183_adcpnp,
 	.sensor_mux_values = mt8183_mux_values,
 	.version = MTK_THERMAL_V1,
+	.raw_to_mcelsius = raw_to_mcelsius_v1,
 };
 
 /**
@@ -639,6 +648,27 @@ static void mtk_thermal_put_bank(struct mtk_thermal_bank *bank)
 		mutex_unlock(&mt->lock);
 }
 
+static u32 _get_sensor_temp(struct mtk_thermal *mt, int id)
+{
+	u32 raw;
+	int temp;
+
+	raw = readl(mt->thermal_base + mt->conf->msr[id]);
+
+	temp = mt->conf->raw_to_mcelsius(mt, id, raw);
+
+	/*
+	 * The first read of a sensor often contains very high bogus
+	 * temperature value. Filter these out so that the system does
+	 * not immediately shut down.
+	 */
+
+	if (temp > 200000)
+		return -EAGAIN;
+	else
+		return temp;
+}
+
 /**
  * mtk_thermal_bank_temperature - get the temperature of a bank
  * @bank:	The bank
@@ -649,28 +679,11 @@ static void mtk_thermal_put_bank(struct mtk_thermal_bank *bank)
 static int mtk_thermal_bank_temperature(struct mtk_thermal_bank *bank)
 {
 	struct mtk_thermal *mt = bank->mt;
-	const struct mtk_thermal_data *conf = mt->conf;
 	int i, temp = INT_MIN, max = INT_MIN;
-	u32 raw;
-
-	for (i = 0; i < conf->bank_data[bank->id].num_sensors; i++) {
-		raw = readl(mt->thermal_base + conf->msr[i]);
 
-		if (mt->conf->version == MTK_THERMAL_V1) {
-			temp = raw_to_mcelsius_v1(
-				mt, conf->bank_data[bank->id].sensors[i], raw);
-		} else {
-			temp = raw_to_mcelsius_v2(
-				mt, conf->bank_data[bank->id].sensors[i], raw);
-		}
+	for (i = 0; i < mt->conf->bank_data[bank->id].num_sensors; i++) {
 
-		/*
-		 * The first read of a sensor often contains very high bogus
-		 * temperature value. Filter these out so that the system does
-		 * not immediately shut down.
-		 */
-		if (temp > 200000)
-			temp = 0;
+		temp = _get_sensor_temp(mt, i);
 
 		if (temp > max)
 			max = temp;
@@ -681,7 +694,8 @@ static int mtk_thermal_bank_temperature(struct mtk_thermal_bank *bank)
 
 static int mtk_read_temp(void *data, int *temperature)
 {
-	struct mtk_thermal *mt = data;
+	struct mtk_thermal_bank *tz = data;
+	struct mtk_thermal *mt = tz->mt;
 	int i;
 	int tempmax = INT_MIN;
 
@@ -700,10 +714,25 @@ static int mtk_read_temp(void *data, int *temperature)
 	return 0;
 }
 
+static int mtk_read_sensor_temp(void *data, int *temperature)
+{
+	struct mtk_thermal_bank *tz = data;
+	struct mtk_thermal *mt = tz->mt;
+	int id = tz->id - 1;
+
+	*temperature = _get_sensor_temp(mt, id);
+
+	return 0;
+}
+
 static const struct thermal_zone_of_device_ops mtk_thermal_ops = {
 	.get_temp = mtk_read_temp,
 };
 
+static const struct thermal_zone_of_device_ops mtk_thermal_sensor_ops = {
+	.get_temp = mtk_read_sensor_temp,
+};
+
 static void mtk_thermal_init_bank(struct mtk_thermal *mt, int num,
 				  u32 apmixed_phys_base, u32 auxadc_phys_base,
 				  int ctrl_id)
@@ -994,6 +1023,7 @@ static int mtk_thermal_probe(struct platform_device *pdev)
 	u64 auxadc_phys_base, apmixed_phys_base;
 	struct thermal_zone_device *tzdev;
 	void __iomem *apmixed_base, *auxadc_base;
+	struct mtk_thermal_bank *tz;
 
 	mt = devm_kzalloc(&pdev->dev, sizeof(*mt), GFP_KERNEL);
 	if (!mt)
@@ -1082,11 +1112,26 @@ static int mtk_thermal_probe(struct platform_device *pdev)
 
 	platform_set_drvdata(pdev, mt);
 
-	tzdev = devm_thermal_zone_of_sensor_register(&pdev->dev, 0, mt,
-						     &mtk_thermal_ops);
-	if (IS_ERR(tzdev)) {
-		ret = PTR_ERR(tzdev);
-		goto err_disable_clk_peri_therm;
+	for (i = 0; i < mt->conf->num_sensors + 1; i++) {
+		tz = devm_kmalloc(&pdev->dev, sizeof(*tz), GFP_KERNEL);
+		if (!tz)
+			return -ENOMEM;
+
+		tz->mt = mt;
+		tz->id = i;
+
+		tzdev = devm_thermal_zone_of_sensor_register(
+						&pdev->dev, i, tz, (i == 0) ?
+						&mtk_thermal_ops :
+						&mtk_thermal_sensor_ops);
+
+		if (IS_ERR(tzdev)) {
+			ret = PTR_ERR(tzdev);
+			dev_err(&pdev->dev,
+				"Error: Failed to register thermal zone %d, ret = %d\n",
+				i, ret);
+			goto err_disable_clk_peri_therm;
+		}
 	}
 
 	ret = devm_thermal_add_hwmon_sysfs(tzdev);
Signature · 1 line
1.8.1.1.dirty
author
#1 lore raw

Hi Maintainers,

Gentle pin for this patch.

Thanks.

Quoted 326 lines · Ben Tseng

From: Michael Kao <[email protected]>

Provide thermal zone to read thermal sensor
in the SoC. We can read all the thermal sensors
value in the SoC by the node /sys/class/thermal/

In mtk_thermal_bank_temperature, return -EAGAIN instead of -EACCESS on the first read of sensor that often are bogus values. This can avoid following warning on boot:

thermal thermal_zone6: failed to read out thermal zone (-13)

---

This patchset supports for MT8183 chip to mtk_thermal.c. Add thermal zone of all the thermal sensor in SoC for another get temperatrue. They don't need to thermal throttle. And we bind coolers for thermal zone nodes of cpu_thermal.

Changes in V9:
- Rebase to kernel-v5.14-rc1
- Bind raw_to_mcelsius_v1 or raw_to_mcelsius_v2 to compatible data of struct mtk_thermal_data
- Remove duplicate struct 'mtk_thermal_bank'
- Remove unnecessary if condition check
- Return error if any thermal zone fail to register

Changes in V8:
- Rebase to kernel-v5.13-rc1
- Resend

Changes in v7:
- Fix build error in v6.

Changes in v6:
- Rebase to kernel-5.11-rc1.
- [1/3]
- add interrupts property.
- [2/3]
- add the Tested-by in the commit message.
- [3/3]
- use the mt->conf->msr[id] instead of conf->msr[id] in the _get_sensor_temp and mtk_thermal_bank_temperature.
- remove the redundant space in _get_sensor_temp and mtk_read_sensor_temp.
- change kmalloc to dev_kmalloc in mtk_thermal_probe.

Changes in v5:
- Rebase to kernel-5.9-rc1.
- Revise the title of cover letter.
- Drop "[v4,7/7] thermal: mediatek: use spinlock to protect
PTPCORESEL"
- [2/2]
- Add the judgement to the version of raw_to_mcelsius.

Changes in v4:
- Rebase to kernel-5.6-rc1.
- [1/7]
- Squash thermal zone settings in the dtsi from [v3,5/8]
arm64: dts: mt8183: Increase polling frequency for CPU
thermal zone.
- Remove the property of interrupts and mediatek,hw-reset-
temp.
- [2/7]
- Correct commit message.
- [4/7]
- Change the target temperature to the 80C and change the
commit message.
- [6/7]
- Adjust newline alignment.
- Fix the judgement on the return value of registering
thermal zone.

Changes in v3:
- Rebase to kernel-5.5-rc1.
- [1/8]
- Update sustainable power of cpu, tzts1~5 and tztsABB.
- [7/8]
- Bypass the failure that non cpu_thermal sensor is not find
in thermal-zones
in dts, which is normal for mt8173, so prompt a warning
here instead of
failing.

Return -EAGAIN instead of -EACCESS on the first read of sensor
that
often are bogus values. This can avoid following warning on
boot:

thermal thermal_zone6: failed to read out thermal zone (-
13)

Changes in v2:
- [1/8]
- Add the sustainable-power,trips,cooling-maps to the
tzts1~tztsABB.
- [4/8]
- Add the min opp of cpu throttle.

Matthias Kaehlcke (1):
arm64: dts: mt8183: Configure CPU cooling

Michael Kao (2):
thermal: mediatek: add another get_temp ops for thermal sensors
arm64: dts: mt8183: add thermal zone node

---
 drivers/thermal/mtk_thermal.c | 95 +++++++++++++++++++++++++++++++
------------
 1 file changed, 70 insertions(+), 25 deletions(-)
drivers/thermal/mtk_thermal.c +1 -0
index ede94ea..8bb0bb2 100644
@@ -271,6 +271,7 @@ struct mtk_thermal_data {
 	bool need_switch_bank;
 	struct thermal_bank_cfg bank_data[MAX_NUM_ZONES];
 	enum mtk_thermal_version version;
+	int (*raw_to_mcelsius)(struct mtk_thermal *mt, int sensno, s32
 raw);
 };
 

struct mtk_thermal {

drivers/thermal/mtk_thermal.c +3 -0
@@ -294,6 +295,9 @@ struct mtk_thermal {
 	struct mtk_thermal_bank banks[MAX_NUM_ZONES];
 };
 
+static int raw_to_mcelsius_v1(struct mtk_thermal *mt, int sensno,
 s32 raw);
+static int raw_to_mcelsius_v2(struct mtk_thermal *mt, int sensno,
 s32 raw);
+
 /* MT8183 thermal sensor data */

static const int mt8183_bank_data[MT8183_NUM_SENSORS] = {
MT8183_TS1, MT8183_TS2, MT8183_TS3, MT8183_TS4, MT8183_TS5,
MT8183_TSABB

drivers/thermal/mtk_thermal.c +26 -0
@@ -427,6 +431,7 @@ struct mtk_thermal {
 	.adcpnp = mt8173_adcpnp,
 	.sensor_mux_values = mt8173_mux_values,
 	.version = MTK_THERMAL_V1,
+	.raw_to_mcelsius = raw_to_mcelsius_v1,
 };
 
 /*
@@ -458,6 +463,7 @@ struct mtk_thermal {
 	.adcpnp = mt2701_adcpnp,
 	.sensor_mux_values = mt2701_mux_values,
 	.version = MTK_THERMAL_V1,
+	.raw_to_mcelsius = raw_to_mcelsius_v1,
 };
 
 /*
@@ -489,6 +495,7 @@ struct mtk_thermal {
 	.adcpnp = mt2712_adcpnp,
 	.sensor_mux_values = mt2712_mux_values,
 	.version = MTK_THERMAL_V1,
+	.raw_to_mcelsius = raw_to_mcelsius_v1,
 };
 
 /*
@@ -514,6 +521,7 @@ struct mtk_thermal {
 	.adcpnp = mt7622_adcpnp,
 	.sensor_mux_values = mt7622_mux_values,
 	.version = MTK_THERMAL_V2,
+	.raw_to_mcelsius = raw_to_mcelsius_v2,
 };
 
 /*
@@ -547,6 +555,7 @@ struct mtk_thermal {
 	.adcpnp = mt8183_adcpnp,
 	.sensor_mux_values = mt8183_mux_values,
 	.version = MTK_THERMAL_V1,
+	.raw_to_mcelsius = raw_to_mcelsius_v1,
 };
 
 /**
@@ -639,6 +648,27 @@ static void mtk_thermal_put_bank(struct
 mtk_thermal_bank *bank)
 		mutex_unlock(&mt->lock);
 }
 
+static u32 _get_sensor_temp(struct mtk_thermal *mt, int id)
+{
+	u32 raw;
+	int temp;
+
+	raw = readl(mt->thermal_base + mt->conf->msr[id]);
+
+	temp = mt->conf->raw_to_mcelsius(mt, id, raw);
+
+	/*
+	 * The first read of a sensor often contains very high bogus
+	 * temperature value. Filter these out so that the system does
+	 * not immediately shut down.
+	 */
+
+	if (temp > 200000)
+		return -EAGAIN;
+	else
+		return temp;
+}
+
 /**
  * mtk_thermal_bank_temperature - get the temperature of a bank

* @bank: The bank

drivers/thermal/mtk_thermal.c +1 -14
@@ -649,28 +679,11 @@ static void mtk_thermal_put_bank(struct
 mtk_thermal_bank *bank)
 static int mtk_thermal_bank_temperature(struct mtk_thermal_bank
 *bank)
 {
 	struct mtk_thermal *mt = bank->mt;
-	const struct mtk_thermal_data *conf = mt->conf;
 	int i, temp = INT_MIN, max = INT_MIN;
-	u32 raw;
-
-	for (i = 0; i < conf->bank_data[bank->id].num_sensors; i++) {
-		raw = readl(mt->thermal_base + conf->msr[i]);
 
-		if (mt->conf->version == MTK_THERMAL_V1) {
-			temp = raw_to_mcelsius_v1(
-				mt, conf->bank_data[bank-
 >id].sensors[i], raw);
-		} else {
-			temp = raw_to_mcelsius_v2(
-				mt, conf->bank_data[bank-
 >id].sensors[i], raw);
-		}
+	for (i = 0; i < mt->conf->bank_data[bank->id].num_sensors; i++)
 {
 
-		/*
-		 * The first read of a sensor often contains very high

bogus

drivers/thermal/mtk_thermal.c +0 -1
-		 * temperature value. Filter these out so that the

system does

drivers/thermal/mtk_thermal.c +18 -5
-		 * not immediately shut down.
-		 */
-		if (temp > 200000)
-			temp = 0;
+		temp = _get_sensor_temp(mt, i);
 
 		if (temp > max)
 			max = temp;
@@ -681,7 +694,8 @@ static int mtk_thermal_bank_temperature(struct
 mtk_thermal_bank *bank)
 
 static int mtk_read_temp(void *data, int *temperature)
 {
-	struct mtk_thermal *mt = data;
+	struct mtk_thermal_bank *tz = data;
+	struct mtk_thermal *mt = tz->mt;
 	int i;
 	int tempmax = INT_MIN;
@@ -700,10 +714,25 @@ static int mtk_read_temp(void *data, int
 *temperature)
 	return 0;
 }
 
+static int mtk_read_sensor_temp(void *data, int *temperature)
+{
+	struct mtk_thermal_bank *tz = data;
+	struct mtk_thermal *mt = tz->mt;
+	int id = tz->id - 1;
+
+	*temperature = _get_sensor_temp(mt, id);
+
+	return 0;
+}
+
 static const struct thermal_zone_of_device_ops mtk_thermal_ops = {
 	.get_temp = mtk_read_temp,
 };
 
+static const struct thermal_zone_of_device_ops
 mtk_thermal_sensor_ops = {
+	.get_temp = mtk_read_sensor_temp,
+};
+
 static void mtk_thermal_init_bank(struct mtk_thermal *mt, int num,

u32 apmixed_phys_base, u32
auxadc_phys_base,

drivers/thermal/mtk_thermal.c +1 -0
 				  int ctrl_id)
@@ -994,6 +1023,7 @@ static int mtk_thermal_probe(struct
 platform_device *pdev)
 	u64 auxadc_phys_base, apmixed_phys_base;
 	struct thermal_zone_device *tzdev;
 	void __iomem *apmixed_base, *auxadc_base;
+	struct mtk_thermal_bank *tz;
 
 	mt = devm_kzalloc(&pdev->dev, sizeof(*mt), GFP_KERNEL);
drivers/thermal/mtk_thermal.c +10 -5
 	if (!mt)
@@ -1082,11 +1112,26 @@ static int mtk_thermal_probe(struct
 platform_device *pdev)
 
 	platform_set_drvdata(pdev, mt);
 
-	tzdev = devm_thermal_zone_of_sensor_register(&pdev->dev, 0, mt,
-						     &mtk_thermal_ops);
-	if (IS_ERR(tzdev)) {
-		ret = PTR_ERR(tzdev);
-		goto err_disable_clk_peri_therm;
+	for (i = 0; i < mt->conf->num_sensors + 1; i++) {
+		tz = devm_kmalloc(&pdev->dev, sizeof(*tz), GFP_KERNEL);
+		if (!tz)
+			return -ENOMEM;
+
+		tz->mt = mt;
+		tz->id = i;
+
+		tzdev = devm_thermal_zone_of_sensor_register(
+						&pdev->dev, i, tz, (i

== 0) ?

drivers/thermal/mtk_thermal.c +2 -0
+						&mtk_thermal_ops :
+						&mtk_thermal_sensor_ops

);

drivers/thermal/mtk_thermal.c +5 -0
+
+		if (IS_ERR(tzdev)) {
+			ret = PTR_ERR(tzdev);
+			dev_err(&pdev->dev,
+				"Error: Failed to register thermal zone

%d, ret = %d\n",

drivers/thermal/mtk_thermal.c static int mtk_thermal_probe(struct platform_device *pdev) · line 1137

Quoted 6 lines
drivers/thermal/mtk_thermal.c +3 -0
+				i, ret);
+			goto err_disable_clk_peri_therm;
+		}
 	}
 
 	ret = devm_thermal_add_hwmon_sysfs(tzdev);

_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek