Skip to contentSkip to conversation

OMAP3: clean up ASM sleep code

PATCH Superseded jean.pihet at newoldbits.com 3 participants 11 messages Dec 18, 2010 – Dec 20, 2010

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

v6 cover OMAP3: clean up ASM sleep code

From: Jean Pihet <[email protected]>

This patch only contains clean-ups and cosmetic changes, no functional change.

Clean-up of the ASM sleep code, for better readability and easier maintenance.

Applies on top of Nishant's latest idle path errata fixes step 2, cf. http://marc.info/?l=linux-omap&m=129139584919242&w=2

Jean Pihet (7):
OMAP3: remove unused code from the ASM sleep code OMAP2+: use global values for the SRAM PA addresses
OMAP3: remove hardcoded values from the ASM sleep code
OMAP3: re-organize the ASM sleep code
OMAP3: rework of the ASM sleep code execution paths
OMAP3: add comments for low power code errata
OMAP3: ASM sleep code format rework

 arch/arm/mach-omap2/control.c          |    9 +-
 arch/arm/mach-omap2/control.h          |    2 +
 arch/arm/mach-omap2/pm.h               |    1 -
 arch/arm/mach-omap2/pm34xx.c           |    4 +-
 arch/arm/mach-omap2/sdrc.h             |    1 -
 arch/arm/mach-omap2/sleep34xx.S        |  724 +++++++++++++++++---------------
 arch/arm/plat-omap/include/plat/sram.h |   11 +
 arch/arm/plat-omap/sram.c              |    7 +-
 8 files changed, 411 insertions(+), 348 deletions(-)
Signature · 1 line
1.7.2.3
#1 lore raw

PATCH v6 1/7 OMAP3: remove unused code from the ASM sleep code

From: Jean Pihet <[email protected]>

Remove unused code:
- macros,
- variables,
- unused semaphore locking API. This API shall be added back when needed,
- infinite loops for debug.

Tested on N900 and Beagleboard with full RET and OFF modes, using cpuidle and suspend.

---
 arch/arm/mach-omap2/pm.h        |    1 -
 arch/arm/mach-omap2/sleep34xx.S |   58 ++++-----------------------------------
 2 files changed, 6 insertions(+), 53 deletions(-)
arch/arm/mach-omap2/pm.h +0 -1
index aff39d0..e458b2a 100644
@@ -80,7 +80,6 @@ extern void save_secure_ram_context(u32 *addr);
 extern void omap3_save_scratchpad_contents(void);
 
 extern unsigned int omap24xx_idle_loop_suspend_sz;
-extern unsigned int omap34xx_suspend_sz;
 extern unsigned int save_secure_ram_context_sz;
 extern unsigned int omap24xx_cpu_suspend_sz;
 extern unsigned int omap34xx_cpu_suspend_sz;
arch/arm/mach-omap2/sleep34xx.S +6 -52

121 lines not on this page · raw message

Signature · 1 line
1.7.2.3
#2 lore raw

PATCH v6 2/7 OMAP2+: use global values for the SRAM PA addresses

In reply to jean.pihet at newoldbits.com

From: Jean Pihet <[email protected]>

The SRAM PA addresses are locally defined and used at different places, i.e. SRAM management code and idle sleep code.

The macros are now defined at a centralized place, for easier maintenance.

Tested on N900 and Beagleboard with full RET and OFF modes, using cpuidle and suspend.

---
 arch/arm/mach-omap2/sdrc.h             |    1 -
 arch/arm/mach-omap2/sleep34xx.S        |    1 +
 arch/arm/plat-omap/include/plat/sram.h |   11 +++++++++++
 arch/arm/plat-omap/sram.c              |    7 ++-----
 4 files changed, 14 insertions(+), 6 deletions(-)
arch/arm/mach-omap2/sdrc.h +0 -1
index 68f57bb..b3f8379 100644
@@ -74,5 +74,4 @@ static inline u32 sms_read_reg(u16 reg)
  */
 #define SDRC_MPURATE_LOOPS		96
 
-
 #endif
arch/arm/mach-omap2/sleep34xx.S +1 -0
index 2191576..406cd2a 100644
@@ -26,6 +26,7 @@
  */
 #include <linux/linkage.h>
 #include <asm/assembler.h>
+#include <plat/sram.h>
 #include <mach/io.h>
 
 #include "cm.h"
arch/arm/plat-omap/include/plat/sram.h +11 -0
index 5905100..9967d5e 100644
@@ -11,6 +11,7 @@
 #ifndef __ARCH_ARM_OMAP_SRAM_H
 #define __ARCH_ARM_OMAP_SRAM_H
 
+#ifndef __ASSEMBLY__
 extern void * omap_sram_push(void * start, unsigned long size);
 extern void omap_sram_reprogram_clock(u32 dpllctl, u32 ckctl);
 
@@ -74,4 +75,14 @@ extern void omap_push_sram_idle(void);
 static inline void omap_push_sram_idle(void) {}
 #endif /* CONFIG_PM */
 
+#endif /* __ASSEMBLY__ */
+
+/*
+ * OMAP2+: define the SRAM PA addresses.
+ * Used by the SRAM management code and the idle sleep code.
+ */
+#define OMAP2_SRAM_PA		0x40200000
+#define OMAP3_SRAM_PA           0x40200000
+#define OMAP4_SRAM_PA		0x40300000
+
 #endif
arch/arm/plat-omap/sram.c +2 -5
index 819ea0c..1a686c8 100644
@@ -41,15 +41,12 @@
 
 #define OMAP1_SRAM_PA		0x20000000
 #define OMAP1_SRAM_VA		VMALLOC_END
-#define OMAP2_SRAM_PA		0x40200000
-#define OMAP2_SRAM_PUB_PA	0x4020f800
+#define OMAP2_SRAM_PUB_PA	(OMAP2_SRAM_PA + 0xf800)
 #define OMAP2_SRAM_VA		0xfe400000
 #define OMAP2_SRAM_PUB_VA	(OMAP2_SRAM_VA + 0x800)
-#define OMAP3_SRAM_PA           0x40200000
 #define OMAP3_SRAM_VA           0xfe400000
-#define OMAP3_SRAM_PUB_PA       0x40208000
+#define OMAP3_SRAM_PUB_PA       (OMAP3_SRAM_PA + 0x8000)
 #define OMAP3_SRAM_PUB_VA       (OMAP3_SRAM_VA + 0x8000)
-#define OMAP4_SRAM_PA		0x40300000
 #define OMAP4_SRAM_VA		0xfe400000
 #define OMAP4_SRAM_PUB_PA	(OMAP4_SRAM_PA + 0x4000)
 #define OMAP4_SRAM_PUB_VA	(OMAP4_SRAM_VA + 0x4000)
Signature · 1 line
1.7.2.3
#3 lore raw

PATCH v6 3/7 OMAP3: remove hardcoded values from the ASM sleep code

In reply to jean.pihet at newoldbits.com

From: Jean Pihet <[email protected]>

Using macros from existing include files for registers addresses.

Tested on N900 and Beagleboard with full RET and OFF modes, using cpuidle and suspend.

Based on original patch from Vishwa.

---
 arch/arm/mach-omap2/control.h   |    2 ++
 arch/arm/mach-omap2/sleep34xx.S |   29 ++++++++++++++++++-----------
 2 files changed, 20 insertions(+), 11 deletions(-)
arch/arm/mach-omap2/control.h +2 -0
index d7911c5..72efefb 100644
@@ -274,6 +274,8 @@
 #define OMAP343X_SCRATCHPAD_ROM		(OMAP343X_CTRL_BASE + 0x860)
 #define OMAP343X_SCRATCHPAD		(OMAP343X_CTRL_BASE + 0x910)
 #define OMAP343X_SCRATCHPAD_ROM_OFFSET	0x19C
+#define OMAP343X_SCRATCHPAD_REGADDR(reg)	OMAP2_L4_IO_ADDRESS(\
+						OMAP343X_SCRATCHPAD + reg)
 
 /* AM35XX_CONTROL_IPSS_CLK_CTRL bits */
 #define AM35XX_USBOTG_VBUSP_CLK_SHIFT   0
arch/arm/mach-omap2/sleep34xx.S +18 -11
index 406cd2a..8e9f38f 100644
@@ -34,20 +34,27 @@
 #include "sdrc.h"
 #include "control.h"
 
-#define SDRC_SCRATCHPAD_SEM_V	0xfa00291c
-
-#define PM_PREPWSTST_CORE_P	0x48306AE8
+/*
+ * Registers access definitions
+ */
+#define SDRC_SCRATCHPAD_SEM_OFFS	0xc
+#define SDRC_SCRATCHPAD_SEM_V	OMAP343X_SCRATCHPAD_REGADDR\
+					(SDRC_SCRATCHPAD_SEM_OFFS)
+#define PM_PREPWSTST_CORE_P	OMAP3430_PRM_BASE + CORE_MOD +\
+					OMAP3430_PM_PREPWSTST
 #define PM_PWSTCTRL_MPU_P	OMAP3430_PRM_BASE + MPU_MOD + OMAP2_PM_PWSTCTRL
 #define CM_IDLEST1_CORE_V	OMAP34XX_CM_REGADDR(CORE_MOD, CM_IDLEST1)
 #define CM_IDLEST_CKGEN_V	OMAP34XX_CM_REGADDR(PLL_MOD, CM_IDLEST)
-#define SRAM_BASE_P		0x40200000
-#define CONTROL_STAT		0x480022F0
-#define CONTROL_MEM_RTA_CTRL	(OMAP343X_CTRL_BASE\
-					+ OMAP36XX_CONTROL_MEM_RTA_CTRL)
-#define SCRATCHPAD_MEM_OFFS	0x310 /* Move this as correct place is
-				       * available */
-#define SCRATCHPAD_BASE_P	(OMAP343X_CTRL_BASE + OMAP343X_CONTROL_MEM_WKUP\
-						+ SCRATCHPAD_MEM_OFFS)
+#define SRAM_BASE_P		OMAP3_SRAM_PA
+#define CONTROL_STAT		OMAP343X_CTRL_BASE + OMAP343X_CONTROL_STATUS
+#define CONTROL_MEM_RTA_CTRL	(OMAP343X_CTRL_BASE +\
+					OMAP36XX_CONTROL_MEM_RTA_CTRL)
+
+/* Move this as correct place is available */
+#define SCRATCHPAD_MEM_OFFS	0x310
+#define SCRATCHPAD_BASE_P	(OMAP343X_CTRL_BASE +\
+					OMAP343X_CONTROL_MEM_WKUP +\
+					SCRATCHPAD_MEM_OFFS)
 #define SDRC_POWER_V		OMAP34XX_SDRC_REGADDR(SDRC_POWER)
 #define SDRC_SYSCONFIG_P	(OMAP343X_SDRC_BASE + SDRC_SYSCONFIG)
 #define SDRC_MR_0_P		(OMAP343X_SDRC_BASE + SDRC_MR_0)
Signature · 1 line
1.7.2.3
#4 lore raw

PATCH 3/7 OMAP3: remove hardcoded values from the ASM sleep code

Quoted 13 lines

-----Original Message-----
From: [email protected] [mailto:[email protected]]
Sent: Saturday, December 18, 2010 9:15 PM
To: [email protected]
Cc: [email protected]; linux-arm- [email protected]; Jean Pihet; Vishwanath BS
Subject: [PATCH 3/7] OMAP3: remove hardcoded values from the ASM sleep code

From: Jean Pihet <[email protected]>

Using macros from existing include files for registers addresses.

Quoted 7 lines

Tested on N900 and Beagleboard with full RET and OFF modes, using cpuidle and suspend.

Based on original patch from Vishwa.

Cc Vishwanath BS <[email protected]>
Quoted 84 lines
---
 arch/arm/mach-omap2/control.h   |    2 ++
 arch/arm/mach-omap2/sleep34xx.S |   29
++++++++++++++++++-----------
 2 files changed, 20 insertions(+), 11 deletions(-)
arch/arm/mach- renamed from arch/arm/mach-omap2/control.h +0 -0

omap2/control.h
index d7911c5..72efefb 100644

arch/arm/mach-omap2/control.h +2 -0
@@ -274,6 +274,8 @@
 #define OMAP343X_SCRATCHPAD_ROM
 	(OMAP343X_CTRL_BASE + 0x860)
 #define OMAP343X_SCRATCHPAD		(OMAP343X_CTRL_BASE +
 0x910)
 #define OMAP343X_SCRATCHPAD_ROM_OFFSET	0x19C
+#define OMAP343X_SCRATCHPAD_REGADDR(reg)
 	OMAP2_L4_IO_ADDRESS(\
+						OMAP343X_SCRATCHPAD +

reg)

/* AM35XX_CONTROL_IPSS_CLK_CTRL bits */
#define AM35XX_USBOTG_VBUSP_CLK_SHIFT 0

arch/arm/mach- renamed from arch/arm/mach-omap2/sleep34xx.S +0 -0

omap2/sleep34xx.S
index 406cd2a..8e9f38f 100644

arch/arm/mach-omap2/sleep34xx.S +10 -10
@@ -34,20 +34,27 @@
 #include "sdrc.h"
 #include "control.h"
 
-#define SDRC_SCRATCHPAD_SEM_V	0xfa00291c
-
-#define PM_PREPWSTST_CORE_P	0x48306AE8
+/*
+ * Registers access definitions
+ */
+#define SDRC_SCRATCHPAD_SEM_OFFS	0xc
+#define SDRC_SCRATCHPAD_SEM_V
 	OMAP343X_SCRATCHPAD_REGADDR\
+					(SDRC_SCRATCHPAD_SEM_OFFS)
+#define PM_PREPWSTST_CORE_P	OMAP3430_PRM_BASE + CORE_MOD
+\
+					OMAP3430_PM_PREPWSTST
 #define PM_PWSTCTRL_MPU_P	OMAP3430_PRM_BASE + MPU_MOD
+ OMAP2_PM_PWSTCTRL
 #define CM_IDLEST1_CORE_V
 	OMAP34XX_CM_REGADDR(CORE_MOD, CM_IDLEST1)
 #define CM_IDLEST_CKGEN_V	OMAP34XX_CM_REGADDR(PLL_MOD,
 CM_IDLEST)
-#define SRAM_BASE_P		0x40200000
-#define CONTROL_STAT		0x480022F0
-#define CONTROL_MEM_RTA_CTRL	(OMAP343X_CTRL_BASE\
-					+
 OMAP36XX_CONTROL_MEM_RTA_CTRL)
-#define SCRATCHPAD_MEM_OFFS	0x310 /* Move this as correct place is
-				       * available */
-#define SCRATCHPAD_BASE_P	(OMAP343X_CTRL_BASE +

OMAP343X_CONTROL_MEM_WKUP\

arch/arm/mach-omap2/sleep34xx.S +2 -1
-						+ SCRATCHPAD_MEM_OFFS)
+#define SRAM_BASE_P		OMAP3_SRAM_PA
+#define CONTROL_STAT		OMAP343X_CTRL_BASE +

OMAP343X_CONTROL_STATUS

arch/arm/mach-omap2/sleep34xx.S +2 -0
+#define CONTROL_MEM_RTA_CTRL	(OMAP343X_CTRL_BASE +\
+

OMAP36XX_CONTROL_MEM_RTA_CTRL)

arch/arm/mach-omap2/sleep34xx.S +6 -0
+
+/* Move this as correct place is available */
+#define SCRATCHPAD_MEM_OFFS	0x310
+#define SCRATCHPAD_BASE_P	(OMAP343X_CTRL_BASE +\
+					OMAP343X_CONTROL_MEM_WKUP +\
+					SCRATCHPAD_MEM_OFFS)
 #define SDRC_POWER_V

OMAP34XX_SDRC_REGADDR(SDRC_POWER)
#define SDRC_SYSCONFIG_P (OMAP343X_SDRC_BASE +
SDRC_SYSCONFIG)
#define SDRC_MR_0_P (OMAP343X_SDRC_BASE +
SDRC_MR_0)
--
1.7.2.3

#5 lore raw

PATCH v6 4/7 OMAP3: re-organize the ASM sleep code

In reply to jean.pihet at newoldbits.com

From: Jean Pihet <[email protected]>

Organize the code in the following sections:
- register access macros,
- API functions,
- internal functions.

Tested on N900 and Beagleboard with full RET and OFF modes, using cpuidle and suspend.

---
 arch/arm/mach-omap2/sleep34xx.S |  114 +++++++++++++++++++++------------------
 1 files changed, 61 insertions(+), 53 deletions(-)
arch/arm/mach-omap2/sleep34xx.S +61 -53
index 8e9f38f..beeb682 100644
@@ -79,6 +79,7 @@ ENTRY(get_restore_pointer)
         ldmfd   sp!, {pc}     @ restore regs and return
 ENTRY(get_restore_pointer_sz)
         .word   . - get_restore_pointer
+
 	.text
 /* Function call to get the restore pointer for 3630 resume from OFF */
 ENTRY(get_omap3630_restore_pointer)
@@ -89,9 +90,18 @@ ENTRY(get_omap3630_restore_pointer_sz)
         .word   . - get_omap3630_restore_pointer
 
 	.text
+/* Function call to get the restore pointer for ES3 to resume from OFF */
+ENTRY(get_es3_restore_pointer)
+	stmfd	sp!, {lr}	@ save registers on stack
+	adr	r0, restore_es3
+	ldmfd	sp!, {pc}	@ restore regs and return
+ENTRY(get_es3_restore_pointer_sz)
+	.word	. - get_es3_restore_pointer
+
+	.text
 /*
  * L2 cache needs to be toggled for stable OFF mode functionality on 3630.
- * This function sets up a fflag that will allow for this toggling to take
+ * This function sets up a flag that will allow for this toggling to take
  * place on 3630. Hopefully some version in the future maynot need this
  */
 ENTRY(enable_omap3630_toggle_l2_on_restore)
@@ -101,58 +111,6 @@ ENTRY(enable_omap3630_toggle_l2_on_restore)
 	str	r1, l2dis_3630
         ldmfd   sp!, {pc}     @ restore regs and return
 
-	.text
-/* Function call to get the restore pointer for for ES3 to resume from OFF */
-ENTRY(get_es3_restore_pointer)
-	stmfd	sp!, {lr}	@ save registers on stack
-	adr	r0, restore_es3
-	ldmfd	sp!, {pc}	@ restore regs and return
-ENTRY(get_es3_restore_pointer_sz)
-	.word	. - get_es3_restore_pointer
-
-ENTRY(es3_sdrc_fix)
-	ldr	r4, sdrc_syscfg		@ get config addr
-	ldr	r5, [r4]		@ get value
-	tst	r5, #0x100		@ is part access blocked
-	it	eq
-	biceq	r5, r5, #0x100		@ clear bit if set
-	str	r5, [r4]		@ write back change
-	ldr	r4, sdrc_mr_0		@ get config addr
-	ldr	r5, [r4]		@ get value
-	str	r5, [r4]		@ write back change
-	ldr	r4, sdrc_emr2_0		@ get config addr
-	ldr	r5, [r4]		@ get value
-	str	r5, [r4]		@ write back change
-	ldr	r4, sdrc_manual_0	@ get config addr
-	mov	r5, #0x2		@ autorefresh command
-	str	r5, [r4]		@ kick off refreshes
-	ldr	r4, sdrc_mr_1		@ get config addr
-	ldr	r5, [r4]		@ get value
-	str	r5, [r4]		@ write back change
-	ldr	r4, sdrc_emr2_1		@ get config addr
-	ldr	r5, [r4]		@ get value
-	str	r5, [r4]		@ write back change
-	ldr	r4, sdrc_manual_1	@ get config addr
-	mov	r5, #0x2		@ autorefresh command
-	str	r5, [r4]		@ kick off refreshes
-	bx	lr
-sdrc_syscfg:
-	.word	SDRC_SYSCONFIG_P
-sdrc_mr_0:
-	.word	SDRC_MR_0_P
-sdrc_emr2_0:
-	.word	SDRC_EMR2_0_P
-sdrc_manual_0:
-	.word	SDRC_MANUAL_0_P
-sdrc_mr_1:
-	.word	SDRC_MR_1_P
-sdrc_emr2_1:
-	.word	SDRC_EMR2_1_P
-sdrc_manual_1:
-	.word	SDRC_MANUAL_1_P
-ENTRY(es3_sdrc_fix_sz)
-	.word	. - es3_sdrc_fix
-
 /* Function to call rom code to save secure ram context */
 ENTRY(save_secure_ram_context)
 	stmfd	sp!, {r1-r12, lr}	@ save registers on stack
@@ -577,6 +535,56 @@ skip_l2_inval:
 	/* restore regs and return */
 	ldmfd   sp!, {r0-r12, pc}
 
+
+/*
+ * Internal functions
+ */
+
+	.text
+ENTRY(es3_sdrc_fix)
+	ldr	r4, sdrc_syscfg		@ get config addr
+	ldr	r5, [r4]		@ get value
+	tst	r5, #0x100		@ is part access blocked
+	it	eq
+	biceq	r5, r5, #0x100		@ clear bit if set
+	str	r5, [r4]		@ write back change
+	ldr	r4, sdrc_mr_0		@ get config addr
+	ldr	r5, [r4]		@ get value
+	str	r5, [r4]		@ write back change
+	ldr	r4, sdrc_emr2_0		@ get config addr
+	ldr	r5, [r4]		@ get value
+	str	r5, [r4]		@ write back change
+	ldr	r4, sdrc_manual_0	@ get config addr
+	mov	r5, #0x2		@ autorefresh command
+	str	r5, [r4]		@ kick off refreshes
+	ldr	r4, sdrc_mr_1		@ get config addr
+	ldr	r5, [r4]		@ get value
+	str	r5, [r4]		@ write back change
+	ldr	r4, sdrc_emr2_1		@ get config addr
+	ldr	r5, [r4]		@ get value
+	str	r5, [r4]		@ write back change
+	ldr	r4, sdrc_manual_1	@ get config addr
+	mov	r5, #0x2		@ autorefresh command
+	str	r5, [r4]		@ kick off refreshes
+	bx	lr
+
+sdrc_syscfg:
+	.word	SDRC_SYSCONFIG_P
+sdrc_mr_0:
+	.word	SDRC_MR_0_P
+sdrc_emr2_0:
+	.word	SDRC_EMR2_0_P
+sdrc_manual_0:
+	.word	SDRC_MANUAL_0_P
+sdrc_mr_1:
+	.word	SDRC_MR_1_P
+sdrc_emr2_1:
+	.word	SDRC_EMR2_1_P
+sdrc_manual_1:
+	.word	SDRC_MANUAL_1_P
+ENTRY(es3_sdrc_fix_sz)
+	.word	. - es3_sdrc_fix
+
 /* Make sure SDRC accesses are ok */
 wait_sdrc_ok:
 
Signature · 1 line
1.7.2.3
#6 lore raw

PATCH v6 5/7 OMAP3: rework of the ASM sleep code execution paths

In reply to jean.pihet at newoldbits.com

From: Jean Pihet <[email protected]>

- Reworked and simplified the execution paths for better readability and to avoid duplication of code,
- Added comments on the entry and exit points and the interaction with the ROM code for OFF mode restore,
- Reworked the existing comments for better readability.

Tested on N900 and Beagleboard with full RET and OFF modes, using cpuidle and suspend.

---
 arch/arm/mach-omap2/control.c   |    9 +-
 arch/arm/mach-omap2/sleep34xx.S |  317 +++++++++++++++++++++++----------------
 2 files changed, 195 insertions(+), 131 deletions(-)
arch/arm/mach-omap2/control.c +8 -1
index 728f268..f4b19ed 100644
@@ -239,7 +239,14 @@ void omap3_save_scratchpad_contents(void)
 	struct omap3_scratchpad_prcm_block prcm_block_contents;
 	struct omap3_scratchpad_sdrc_block sdrc_block_contents;
 
-	/* Populate the Scratchpad contents */
+	/*
+	 * Populate the Scratchpad contents
+	 *
+	 * The "get_*restore_pointer" functions are used to provide a
+	 * physical restore address where the ROM code jumps while waking
+	 * up from MPU OFF/OSWR state.
+	 * The restore pointer is stored into the scratchpad.
+	 */
 	scratchpad_contents.boot_config_ptr = 0x0;
 	if (cpu_is_omap3630())
 		scratchpad_contents.public_restore_ptr =
arch/arm/mach-omap2/sleep34xx.S +187 -130

376 lines not on this page · raw message

Signature · 1 line
1.7.2.3
#7 lore raw

PATCH v6 6/7 OMAP3: add comments for low power code errata

In reply to jean.pihet at newoldbits.com

From: Jean Pihet <[email protected]>

Errata covered:
- 1.157 & 1.185
- i443
- i581

Tested on N900 and Beagleboard with full RET and OFF modes, using cpuidle and suspend.

---
 arch/arm/mach-omap2/pm34xx.c    |    4 ++--
 arch/arm/mach-omap2/sleep34xx.S |   11 +++++++++++
 2 files changed, 13 insertions(+), 2 deletions(-)
arch/arm/mach-omap2/pm34xx.c +2 -2
index adc0917..267f015 100644
@@ -148,7 +148,7 @@ static void omap3_core_save_context(void)
 
 	/*
 	 * Force write last pad into memory, as this can fail in some
-	 * cases according to erratas 1.157, 1.185
+	 * cases according to errata 1.157, 1.185
 	 */
 	omap_ctrl_writel(omap_ctrl_readl(OMAP343X_PADCONF_ETK_D14),
 		OMAP343X_CONTROL_MEM_WKUP + 0x2a0);
@@ -446,7 +446,7 @@ void omap_sram_idle(void)
 	/*
 	* On EMU/HS devices ROM code restores a SRDC value
 	* from scratchpad which has automatic self refresh on timeout
-	* of AUTO_CNT = 1 enabled. This takes care of errata 1.142.
+	* of AUTO_CNT = 1 enabled. This takes care of erratum ID i443.
 	* Hence store/restore the SDRC_POWER register here.
 	*/
 	if (omap_rev() >= OMAP3430_REV_ES3_0 &&
arch/arm/mach-omap2/sleep34xx.S +11 -0
index 0e27429..7a63da2 100644
@@ -596,6 +596,7 @@ usettbr0:
  * Internal functions
  */
 
+/* This function implements the erratum ID i443 WA, applies to 34xx >= ES3.0 */
 	.text
 ENTRY(es3_sdrc_fix)
 	ldr	r4, sdrc_syscfg		@ get config addr
@@ -641,6 +642,16 @@ sdrc_manual_1:
 ENTRY(es3_sdrc_fix_sz)
 	.word	. - es3_sdrc_fix
 
+/*
+ * This function implements the erratum ID i581 WA:
+ *  SDRC state restore before accessing the SDRAM
+ *
+ * Only used at return from non-OFF mode. For OFF
+ * mode the ROM code configures the SDRC and
+ * the DPLL before calling the restore code directly
+ * from DDR.
+ */
+
 /* Make sure SDRC accesses are ok */
 wait_sdrc_ok:
 
Signature · 1 line
1.7.2.3
#8 lore raw

PATCH v6 7/7 OMAP3: ASM sleep code format rework

In reply to jean.pihet at newoldbits.com

From: Jean Pihet <[email protected]>

Cosmetic fixes to the code:
- white spaces and tabs,
- alignement,
- comments rephrase and typos,
- multi-line comments

Tested on N900 and Beagleboard with full RET and OFF modes, using cpuidle and suspend.

---
 arch/arm/mach-omap2/sleep34xx.S |  224 ++++++++++++++++++++-------------------
 1 files changed, 117 insertions(+), 107 deletions(-)
arch/arm/mach-omap2/sleep34xx.S +117 -107
index 7a63da2..29f4bf7 100644
@@ -1,6 +1,4 @@
 /*
- * linux/arch/arm/mach-omap2/sleep.S
- *
  * (C) Copyright 2007
  * Texas Instruments
  * Karthik Dasu <[email protected]>
@@ -81,20 +79,20 @@
 	.text
 /* Function call to get the restore pointer for resume from OFF */
 ENTRY(get_restore_pointer)
-        stmfd   sp!, {lr}     @ save registers on stack
+	stmfd	sp!, {lr}	@ save registers on stack
 	adr	r0, restore
-        ldmfd   sp!, {pc}     @ restore regs and return
+	ldmfd	sp!, {pc}	@ restore regs and return
 ENTRY(get_restore_pointer_sz)
-        .word   . - get_restore_pointer
+	.word	. - get_restore_pointer
 
 	.text
 /* Function call to get the restore pointer for 3630 resume from OFF */
 ENTRY(get_omap3630_restore_pointer)
-        stmfd   sp!, {lr}     @ save registers on stack
+	stmfd	sp!, {lr}	@ save registers on stack
 	adr	r0, restore_3630
-        ldmfd   sp!, {pc}     @ restore regs and return
+	ldmfd	sp!, {pc}	@ restore regs and return
 ENTRY(get_omap3630_restore_pointer_sz)
-        .word   . - get_omap3630_restore_pointer
+	.word	. - get_omap3630_restore_pointer
 
 	.text
 /* Function call to get the restore pointer for ES3 to resume from OFF */
@@ -112,16 +110,16 @@ ENTRY(get_es3_restore_pointer_sz)
  * place on 3630. Hopefully some version in the future may not need this.
  */
 ENTRY(enable_omap3630_toggle_l2_on_restore)
-        stmfd   sp!, {lr}     @ save registers on stack
+	stmfd	sp!, {lr}	@ save registers on stack
 	/* Setup so that we will disable and enable l2 */
 	mov	r1, #0x1
 	str	r1, l2dis_3630
-        ldmfd   sp!, {pc}     @ restore regs and return
+	ldmfd	sp!, {pc}	@ restore regs and return
 
+	.text
 /* Function to call rom code to save secure ram context */
 ENTRY(save_secure_ram_context)
 	stmfd	sp!, {r1-r12, lr}	@ save registers on stack
-
 	adr	r3, api_params		@ r3 points to parameters
 	str	r0, [r3,#0x4]		@ r0 has sdram address
 	ldr	r12, high_mask
@@ -165,14 +163,14 @@ ENTRY(save_secure_ram_context_sz)
  *
  *
  * Notes:
- * - this code gets copied to internal SRAM at boot. The execution pointer
- *   in SRAM is _omap_sram_idle.
+ * - this code gets copied to internal SRAM at boot and after wake-up
+ *   from OFF mode. The execution pointer in SRAM is _omap_sram_idle.
  * - when the OMAP wakes up it continues at different execution points
  *   depending on the low power mode (non-OFF vs OFF modes),
  *   cf. 'Resume path for xxx mode' comments.
  */
 ENTRY(omap34xx_cpu_suspend)
-	stmfd	sp!, {r0-r12, lr}		@ save registers on stack
+	stmfd	sp!, {r0-r12, lr}	@ save registers on stack
 
 	/*
 	 * r0 contains restore pointer in sdram
@@ -280,9 +278,9 @@ clean_l2:
 	 *  - should be faster and will change with kernel
 	 *  - 'might' have to copy address, load and jump to it
 	 */
-	ldr r1, kernel_flush
-	mov lr, pc
-	bx  r1
+	ldr	r1, kernel_flush
+	mov	lr, pc
+	bx	r1
 
 omap3_do_wfi:
 	ldr	r4, sdrc_power		@ read the SDRC_POWER register
@@ -375,18 +373,18 @@ restore_3630:
 	/* Fall through to common code for the remaining logic */
 
 restore:
-        /*
+	/*
 	 * Check what was the reason for mpu reset and store the reason in r9:
 	 *  0 - No context lost
-         *  1 - Only L1 and logic lost
-         *  2 - Only L2 lost - In this case, we wont be here
-         *  3 - Both L1 and L2 lost
+	 *  1 - Only L1 and logic lost
+	 *  2 - Only L2 lost - In this case, we wont be here
+	 *  3 - Both L1 and L2 lost
 	 */
-	ldr     r1, pm_pwstctrl_mpu
+	ldr	r1, pm_pwstctrl_mpu
 	ldr	r2, [r1]
-	and     r2, r2, #0x3
-	cmp     r2, #0x0	@ Check if target power state was OFF or RET
-        moveq   r9, #0x3        @ MPU OFF => L1 and L2 lost
+	and	r2, r2, #0x3
+	cmp	r2, #0x0	@ Check if target power state was OFF or RET
+	moveq	r9, #0x3	@ MPU OFF => L1 and L2 lost
 	movne	r9, #0x1	@ Only L1 and L2 lost => avoid L2 invalidation
 	bne	logic_l1_restore
 
@@ -402,71 +400,74 @@ skipl2dis:
 	and	r1, #0x700
 	cmp	r1, #0x300
 	beq	l2_inv_gp
-	mov	r0, #40		@ set service ID for PPA
-	mov	r12, r0		@ copy secure Service ID in r12
-	mov	r1, #0		@ set task id for ROM code in r1
-	mov	r2, #4		@ set some flags in r2, r6
+	mov	r0, #40			@ set service ID for PPA
+	mov	r12, r0			@ copy secure Service ID in r12
+	mov	r1, #0			@ set task id for ROM code in r1
+	mov	r2, #4			@ set some flags in r2, r6
 	mov	r6, #0xff
 	adr	r3, l2_inv_api_params	@ r3 points to dummy parameters
 	mcr	p15, 0, r0, c7, c10, 4	@ data write barrier
 	mcr	p15, 0, r0, c7, c10, 5	@ data memory barrier
 	.word	0xE1600071		@ call SMI monitor (smi #1)
 	/* Write to Aux control register to set some bits */
-	mov	r0, #42		@ set service ID for PPA
-	mov	r12, r0		@ copy secure Service ID in r12
-	mov	r1, #0		@ set task id for ROM code in r1
-	mov	r2, #4		@ set some flags in r2, r6
+	mov	r0, #42			@ set service ID for PPA
+	mov	r12, r0			@ copy secure Service ID in r12
+	mov	r1, #0			@ set task id for ROM code in r1
+	mov	r2, #4			@ set some flags in r2, r6
 	mov	r6, #0xff
 	ldr	r4, scratchpad_base
-	ldr	r3, [r4, #0xBC]	@ r3 points to parameters
+	ldr	r3, [r4, #0xBC]		@ r3 points to parameters
 	mcr	p15, 0, r0, c7, c10, 4	@ data write barrier
 	mcr	p15, 0, r0, c7, c10, 5	@ data memory barrier
 	.word	0xE1600071		@ call SMI monitor (smi #1)
 
 #ifdef CONFIG_OMAP3_L2_AUX_SECURE_SAVE_RESTORE
 	/* Restore L2 aux control register */
-	@ set service ID for PPA
+					@ set service ID for PPA
 	mov	r0, #CONFIG_OMAP3_L2_AUX_SECURE_SERVICE_SET_ID
-	mov	r12, r0		@ copy service ID in r12
-	mov	r1, #0		@ set task ID for ROM code in r1
-	mov	r2, #4		@ set some flags in r2, r6
+	mov	r12, r0			@ copy service ID in r12
+	mov	r1, #0			@ set task ID for ROM code in r1
+	mov	r2, #4			@ set some flags in r2, r6
 	mov	r6, #0xff
 	ldr	r4, scratchpad_base
 	ldr	r3, [r4, #0xBC]
-	adds	r3, r3, #8	@ r3 points to parameters
+	adds	r3, r3, #8		@ r3 points to parameters
 	mcr	p15, 0, r0, c7, c10, 4	@ data write barrier
 	mcr	p15, 0, r0, c7, c10, 5	@ data memory barrier
 	.word	0xE1600071		@ call SMI monitor (smi #1)
 #endif
 	b	logic_l1_restore
+
 l2_inv_api_params:
-	.word   0x1, 0x00
+	.word	0x1, 0x00
 l2_inv_gp:
 	/* Execute smi to invalidate L2 cache */
-	mov r12, #0x1                         @ set up to invalide L2
-smi:    .word 0xE1600070		@ Call SMI monitor (smieq)
+	mov r12, #0x1			@ set up to invalidate L2
+	.word 0xE1600070		@ Call SMI monitor (smieq)
 	/* Write to Aux control register to set some bits */
 	ldr	r4, scratchpad_base
 	ldr	r3, [r4,#0xBC]
 	ldr	r0, [r3,#4]
 	mov	r12, #0x3
-	.word 0xE1600070	@ Call SMI monitor (smieq)
+	.word	0xE1600070		@ Call SMI monitor (smieq)
 	ldr	r4, scratchpad_base
 	ldr	r3, [r4,#0xBC]
 	ldr	r0, [r3,#12]
 	mov	r12, #0x2
-	.word 0xE1600070	@ Call SMI monitor (smieq)
+	.word	0xE1600070		@ Call SMI monitor (smieq)
 logic_l1_restore:
 	ldr	r1, l2dis_3630
-	cmp	r1, #0x1	@ Do we need to re-enable L2 on 3630?
+	cmp	r1, #0x1		@ Test if L2 re-enable needed on 3630
 	bne	skipl2reen
 	mrc	p15, 0, r1, c1, c0, 1
-	orr	r1, r1, #2	@ re-enable L2 cache
+	orr	r1, r1, #2		@ re-enable L2 cache
 	mcr	p15, 0, r1, c1, c0, 1
 skipl2reen:
 	mov	r1, #0
-	/* Invalidate all instruction caches to PoU
-	 * and flush branch target cache */
+	/*
+	 * Invalidate all instruction caches to PoU
+	 * and flush branch target cache
+	 */
 	mcr	p15, 0, r1, c7, c5, 0
 
 	ldr	r4, scratchpad_base
@@ -487,33 +488,33 @@ skipl2reen:
 	MCR p15, 0, r6, c2, c0, 1
 	/* Translation table base control register */
 	MCR p15, 0, r7, c2, c0, 2
-	/*domain access Control Register */
+	/* Domain access Control Register */
 	MCR p15, 0, r8, c3, c0, 0
-	/* data fault status Register */
+	/* Data fault status Register */
 	MCR p15, 0, r9, c5, c0, 0
 
-	ldmia  r3!,{r4-r8}
-	/* instruction fault status Register */
+	ldmia	r3!,{r4-r8}
+	/* Instruction fault status Register */
 	MCR p15, 0, r4, c5, c0, 1
-	/*Data Auxiliary Fault Status Register */
+	/* Data Auxiliary Fault Status Register */
 	MCR p15, 0, r5, c5, c1, 0
-	/*Instruction Auxiliary Fault Status Register*/
+	/* Instruction Auxiliary Fault Status Register*/
 	MCR p15, 0, r6, c5, c1, 1
-	/*Data Fault Address Register */
+	/* Data Fault Address Register */
 	MCR p15, 0, r7, c6, c0, 0
-	/*Instruction Fault Address Register*/
+	/* Instruction Fault Address Register*/
 	MCR p15, 0, r8, c6, c0, 2
-	ldmia  r3!,{r4-r7}
+	ldmia	r3!,{r4-r7}
 
-	/* user r/w thread and process ID */
+	/* User r/w thread and process ID */
 	MCR p15, 0, r4, c13, c0, 2
-	/* user ro thread and process ID */
+	/* User ro thread and process ID */
 	MCR p15, 0, r5, c13, c0, 3
-	/*Privileged only thread and process ID */
+	/* Privileged only thread and process ID */
 	MCR p15, 0, r6, c13, c0, 4
-	/* cache size selection */
+	/* Cache size selection */
 	MCR p15, 2, r7, c0, c0, 0
-	ldmia  r3!,{r4-r8}
+	ldmia	r3!,{r4-r8}
 	/* Data TLB lockdown registers */
 	MCR p15, 0, r4, c10, c0, 0
 	/* Instruction TLB lockdown registers */
@@ -525,26 +526,27 @@ skipl2reen:
 	/* Context PID */
 	MCR p15, 0, r8, c13, c0, 1
 
-	ldmia  r3!,{r4-r5}
-	/* primary memory remap register */
+	ldmia	r3!,{r4-r5}
+	/* Primary memory remap register */
 	MCR p15, 0, r4, c10, c2, 0
-	/*normal memory remap register */
+	/* Normal memory remap register */
 	MCR p15, 0, r5, c10, c2, 1
 
 	/* Restore cpsr */
-	ldmia	r3!,{r4}	/*load CPSR from SDRAM*/
-	msr	cpsr, r4	/*store cpsr */
+	ldmia	r3!,{r4}		@ load CPSR from SDRAM
+	msr	cpsr, r4		@ store cpsr
 
 	/* Enabling MMU here */
-	mrc	p15, 0, r7, c2, c0, 2 /* Read TTBRControl */
-	/* Extract N (0:2) bits and decide whether to use TTBR0 or TTBR1*/
+	mrc	p15, 0, r7, c2, c0, 2 	@ Read TTBRControl
+	/* Extract N (0:2) bits and decide whether to use TTBR0 or TTBR1 */
 	and	r7, #0x7
 	cmp	r7, #0x0
 	beq	usettbr0
 ttbr_error:
-	/* More work needs to be done to support N[0:2] value other than 0
-	* So looping here so that the error can be detected
-	*/
+	/*
+	 * More work needs to be done to support N[0:2] value other than 0
+	 * So looping here so that the error can be detected
+	 */
 	b	ttbr_error
 usettbr0:
 	mrc	p15, 0, r2, c2, c0, 0
@@ -552,21 +554,25 @@ usettbr0:
 	and	r2, r5
 	mov	r4, pc
 	ldr	r5, table_index_mask
-	and	r4, r5 /* r4 = 31 to 20 bits of pc */
+	and	r4, r5			@ r4 = 31 to 20 bits of pc
 	/* Extract the value to be written to table entry */
 	ldr	r1, table_entry
-	add	r1, r1, r4 /* r1 has value to be written to table entry*/
+	/* r1 has the value to be written to table entry*/
+	add	r1, r1, r4
 	/* Getting the address of table entry to modify */
 	lsr	r4, #18
-	add	r2, r4 /* r2 has the location which needs to be modified */
+	/* r2 has the location which needs to be modified */
+	add	r2, r4
 	/* Storing previous entry of location being modified */
 	ldr	r5, scratchpad_base
 	ldr	r4, [r2]
 	str	r4, [r5, #0xC0]
 	/* Modify the table entry */
 	str	r1, [r2]
-	/* Storing address of entry being modified
-	 * - will be restored after enabling MMU */
+	/*
+	 * Storing address of entry being modified
+	 * - will be restored after enabling MMU
+	 */
 	ldr	r5, scratchpad_base
 	str	r2, [r5, #0xC4]
 
@@ -575,8 +581,11 @@ usettbr0:
 	mcr	p15, 0, r0, c7, c5, 6	@ Invalidate branch predictor array
 	mcr	p15, 0, r0, c8, c5, 0	@ Invalidate instruction TLB
 	mcr	p15, 0, r0, c8, c6, 0	@ Invalidate data TLB
-	/* Restore control register  but dont enable caches here*/
-	/* Caches will be enabled after restoring MMU table entry */
+	/*
+	 * Restore control register. This enables the MMU.
+	 * The caches and prediction are not enabled here, they
+	 * will be enabled after restoring the MMU table entry.
+	 */
 	ldmia	r3!, {r4}
 	/* Store previous value of control register in scratchpad */
 	str	r4, [r5, #0xC8]
@@ -589,7 +598,7 @@ usettbr0:
  * == Exit point from OFF mode ==
  * ==============================
  */
-	ldmfd	sp!, {r0-r12, pc}		@ restore regs and return
+	ldmfd	sp!, {r0-r12, pc}	@ restore regs and return
 
 
 /*
@@ -655,55 +664,56 @@ ENTRY(es3_sdrc_fix_sz)
 /* Make sure SDRC accesses are ok */
 wait_sdrc_ok:
 
-/* DPLL3 must be locked before accessing the SDRC. Maybe the HW ensures this. */
+/* DPLL3 must be locked before accessing the SDRC. Maybe the HW ensures this */
 	ldr	r4, cm_idlest_ckgen
 wait_dpll3_lock:
 	ldr	r5, [r4]
 	tst	r5, #1
 	beq	wait_dpll3_lock
 
-        ldr     r4, cm_idlest1_core
+	ldr	r4, cm_idlest1_core
 wait_sdrc_ready:
-        ldr     r5, [r4]
-        tst     r5, #0x2
-        bne     wait_sdrc_ready
+	ldr	r5, [r4]
+	tst	r5, #0x2
+	bne	wait_sdrc_ready
 	/* allow DLL powerdown upon hw idle req */
-        ldr     r4, sdrc_power
-        ldr     r5, [r4]
-        bic     r5, r5, #0x40
-        str     r5, [r4]
-is_dll_in_lock_mode:
+	ldr	r4, sdrc_power
+	ldr	r5, [r4]
+	bic	r5, r5, #0x40
+	str	r5, [r4]
 
-        /* Is dll in lock mode? */
-        ldr     r4, sdrc_dlla_ctrl
-        ldr     r5, [r4]
-        tst     r5, #0x4
-        bxne    lr
-        /* wait till dll locks */
+is_dll_in_lock_mode:
+	/* Is dll in lock mode? */
+	ldr	r4, sdrc_dlla_ctrl
+	ldr	r5, [r4]
+	tst	r5, #0x4
+	bxne	lr			@ Return if locked
+	/* wait till dll locks */
 wait_dll_lock_timed:
 	ldr	r4, wait_dll_lock_counter
 	add	r4, r4, #1
 	str	r4, wait_dll_lock_counter
 	ldr	r4, sdrc_dlla_status
-        mov	r6, #8		/* Wait 20uS for lock */
+	/* Wait 20uS for lock */
+	mov	r6, #8
 wait_dll_lock:
 	subs	r6, r6, #0x1
 	beq	kick_dll
-        ldr     r5, [r4]
-        and     r5, r5, #0x4
-        cmp     r5, #0x4
-        bne     wait_dll_lock
-        bx      lr
+	ldr	r5, [r4]
+	and	r5, r5, #0x4
+	cmp	r5, #0x4
+	bne	wait_dll_lock
+	bx	lr			@ Return when locked
 
 	/* disable/reenable DLL if not locked */
 kick_dll:
 	ldr	r4, sdrc_dlla_ctrl
 	ldr	r5, [r4]
 	mov	r6, r5
-	bic	r6, #(1<<3)	/* disable dll */
+	bic	r6, #(1<<3)		@ disable dll
 	str	r6, [r4]
 	dsb
-	orr	r6, r6, #(1<<3)	/* enable dll */
+	orr	r6, r6, #(1<<3)		@ enable dll
 	str	r6, [r4]
 	dsb
 	ldr	r4, kick_counter
@@ -728,7 +738,7 @@ scratchpad_base:
 sram_base:
 	.word	SRAM_BASE_P + 0x8000
 sdrc_power:
-	.word SDRC_POWER_V
+	.word	SDRC_POWER_V
 ttbrbit_mask:
 	.word	0xFFFFC000
 table_index_mask:
@@ -742,9 +752,9 @@ control_stat:
 control_mem_rta:
 	.word	CONTROL_MEM_RTA_CTRL
 kernel_flush:
-	.word v7_flush_dcache_all
+	.word	v7_flush_dcache_all
 l2dis_3630:
-	.word 0
+	.word	0
 	/* these 2 words need to be@the end !!! */
 kick_counter:
 	.word	0
Signature · 1 line
1.7.2.3
#9 lore raw

v6 cover OMAP3: clean up ASM sleep code

In reply to jean.pihet at newoldbits.com

jean.pihet at newoldbits.com had written, on 12/18/2010 09:44 AM, the following:

Quoted 4 lines

Applies on top of Nishant's latest idle path errata fixes step 2, cf. http://marc.info/?l=linux-omap&m=129139584919242&w=2

Quoted 9 lines

Jean Pihet (7):
OMAP3: remove unused code from the ASM sleep code OMAP2+: use global values for the SRAM PA addresses
OMAP3: remove hardcoded values from the ASM sleep code
OMAP3: re-organize the ASM sleep code
OMAP3: rework of the ASM sleep code execution paths
OMAP3: add comments for low power code errata
OMAP3: ASM sleep code format rework

just FYI - tested the series v6 as well with:
SDP3430 and SDP3630 with script:
http://elinux.org/OMAP_Power_Management#Quick_verification_of_suspend-idle_functionality

Tested against v4 of my series. I have ensured that your series still applies cleanly on top of my new series.

Signature · 2 lines
Regards,
Nishanth Menon
author
#10 lore raw

v6 cover OMAP3: clean up ASM sleep code

Hi Nishant,

Quoted 16 lines · Nishanth Menon

jean.pihet at newoldbits.com had written, on 12/18/2010 09:44 AM, the following:

Quoted 4 lines

Applies on top of Nishant's latest idle path errata fixes step 2, cf. http://marc.info/?l=linux-omap&m=129139584919242&w=2

Quoted 9 lines

Jean Pihet (7):
?OMAP3: remove unused code from the ASM sleep code ?OMAP2+: use global values for the SRAM PA addresses ?OMAP3: remove hardcoded values from the ASM sleep code ?OMAP3: re-organize the ASM sleep code
?OMAP3: rework of the ASM sleep code execution paths ?OMAP3: add comments for low power code errata ?OMAP3: ASM sleep code format rework

Quoted 6 lines

just FYI - tested the series v6 as well with:
SDP3430 and SDP3630 with script:
http://elinux.org/OMAP_Power_Management#Quick_verification_of_suspend-idle_functionality

Tested against v4 of my series. I have ensured that your series still applies cleanly on top of my new series.

Thanks for that!

Let me check and ack your latest v4 patches.

Quoted 6 lines

--
Regards,
Nishanth Menon

Regards,
Jean