"Bluetooth: hci0: HCI_REQ-0xfcf0" errors in dmesg
Hello,
On 6.1.0-rc3, I have been seeing this error message in dmesg:
Bluetooth: hci0: HCI_REQ-0xfcf0
It is printed on every boot, resume from suspend and rfkill unblock of the Bluetooth device. The device seems to be functioning normally though (but I have done limited testing only).
After some investigation, it turned out to be caused by
commit dd50a864ffae ("Bluetooth: Delete unreferenced hci_request code") which modified hci_req_add() in net/bluetooth/hci_request.c to always print an error message when that function is executed.
I have added dump_stack() to hci_req_add() and got the following backtraces:
On boot:
[ 18.487766] Bluetooth: hci0: RTL: fw version 0xab6b705c
[ 18.548951] Bluetooth: hci0: HCI_REQ-0xfcf0
[ 18.548961] CPU: 3 PID: 108 Comm: kworker/u9:0 Not tainted 6.1.0-rc3unif4-00001-gb33a0948e932 #86 [ 18.548965] Hardware name: HP HP Laptop 17-by0xxx/84CA, BIOS F.66 03/29/2022
[ 18.548968] Workqueue: hci0 hci_power_on [bluetooth]
[ 18.549018] Call Trace:
[ 18.549020] <TASK>
[ 18.549022] dump_stack_lvl+0x38/0x4d
[ 18.549030] dump_stack+0x10/0x16
[ 18.549035] hci_req_add+0x47/0x70 [bluetooth]
[ 18.549093] msft_set_filter_enable+0x59/0x90 [bluetooth]
[ 18.549147] msft_do_open+0x131/0x220 [bluetooth]
[ 18.549198] hci_dev_open_sync+0x646/0xc20 [bluetooth]
[ 18.549249] hci_dev_do_open+0x2a/0x60 [bluetooth]
[ 18.549282] hci_power_on+0x53/0x210 [bluetooth]
[ 18.549317] process_one_work+0x21f/0x3f0
[ 18.549323] worker_thread+0x4a/0x3c0
[ 18.549328] ? process_one_work+0x3f0/0x3f0
[ 18.549332] kthread+0xff/0x130
[ 18.549336] ? kthread_complete_and_exit+0x20/0x20
[ 18.549340] ret_from_fork+0x22/0x30
[ 18.549347] </TASK>
[ 21.165060] EXT4-fs (dm-7): mounted filesystem with ordered data mode. Quota mode: none.
on rfkill unblock:
[ 1671.040970] Bluetooth: hci0: HCI_REQ-0xfcf0 [ 1671.040992] CPU: 3 PID: 5006 Comm: kworker/u9:2 Not tainted 6.1.0-rc3unif4-00001-gb33a0948e932 #86 [ 1671.041005] Hardware name: HP HP Laptop 17-by0xxx/84CA, BIOS F.66 03/29/2022 [ 1671.041012] Workqueue: hci0 hci_cmd_sync_work [bluetooth] [ 1671.041194] Call Trace: [ 1671.041200] <TASK> [ 1671.041208] dump_stack_lvl+0x38/0x4d [ 1671.041227] dump_stack+0x10/0x16 [ 1671.041241] hci_req_add+0x47/0x70 [bluetooth] [ 1671.041408] msft_set_filter_enable+0x59/0x90 [bluetooth] [ 1671.041579] msft_do_open+0x131/0x220 [bluetooth] [ 1671.041683] hci_dev_open_sync+0x646/0xc20 [bluetooth] [ 1671.041787] hci_set_powered_sync+0xd4/0x240 [bluetooth] [ 1671.041887] set_powered_sync+0x20/0x60 [bluetooth] [ 1671.041975] hci_cmd_sync_work+0xa8/0x150 [bluetooth] [ 1671.042079] process_one_work+0x21f/0x3f0 [ 1671.042092] worker_thread+0x4a/0x3c0 [ 1671.042102] ? process_one_work+0x3f0/0x3f0 [ 1671.042111] kthread+0xff/0x130 [ 1671.042119] ? kthread_complete_and_exit+0x20/0x20 [ 1671.042128] ret_from_fork+0x22/0x30 [ 1671.042142] </TASK>
My hardware: HP laptop 17-by0001nw, device is a Realtek combo card:
"Realtek RTL8822BE 802.11 ac 2×2 WiFi + Bluetooth 4.2 Combo Adapter (MU-MIMO supported)"
I am ready to provide additional information and testing, if need be.
Greetings,
Mateusz Jończyk
Luiz Augusto von Dentz
maintainerHi,
Quoted 68 lines · Mateusz Jończyk
Hello,
On 6.1.0-rc3, I have been seeing this error message in dmesg:
Bluetooth: hci0: HCI_REQ-0xfcf0It is printed on every boot, resume from suspend and rfkill unblock of the Bluetooth device. The device seems to be functioning normally though (but I have done limited testing only).
After some investigation, it turned out to be caused by
commitdd50a864ffae("Bluetooth: Delete unreferencedhci_requestcode")
which modifiedhci_req_add()innet/bluetooth/hci_request.cto always print an error message when that function is executed.I have added
dump_stack()tohci_req_add()and got the following backtraces:On boot:
[ 18.487766] Bluetooth: hci0: RTL: fw version 0xab6b705c [ 18.548951] Bluetooth: hci0: HCI_REQ-0xfcf0 [ 18.548961] CPU: 3 PID: 108 Comm: kworker/u9:0 Not tainted 6.1.0-rc3unif4-00001-gb33a0948e932 #86 [ 18.548965] Hardware name: HP HP Laptop 17-by0xxx/84CA, BIOS F.66 03/29/2022 [ 18.548968] Workqueue: hci0 hci_power_on [bluetooth] [ 18.549018] Call Trace: [ 18.549020] <TASK> [ 18.549022] dump_stack_lvl+0x38/0x4d [ 18.549030] dump_stack+0x10/0x16 [ 18.549035] hci_req_add+0x47/0x70 [bluetooth] [ 18.549093] msft_set_filter_enable+0x59/0x90 [bluetooth] [ 18.549147] msft_do_open+0x131/0x220 [bluetooth] [ 18.549198] hci_dev_open_sync+0x646/0xc20 [bluetooth] [ 18.549249] hci_dev_do_open+0x2a/0x60 [bluetooth] [ 18.549282] hci_power_on+0x53/0x210 [bluetooth] [ 18.549317] process_one_work+0x21f/0x3f0 [ 18.549323] worker_thread+0x4a/0x3c0 [ 18.549328] ? process_one_work+0x3f0/0x3f0 [ 18.549332] kthread+0xff/0x130 [ 18.549336] ? kthread_complete_and_exit+0x20/0x20 [ 18.549340] ret_from_fork+0x22/0x30 [ 18.549347] </TASK> [ 21.165060] EXT4-fs (dm-7): mounted filesystem with ordered data mode. Quota mode: none.on rfkill unblock:
[ 1671.040970] Bluetooth: hci0: HCI_REQ-0xfcf0 [ 1671.040992] CPU: 3 PID: 5006 Comm: kworker/u9:2 Not tainted 6.1.0-rc3unif4-00001-gb33a0948e932 #86 [ 1671.041005] Hardware name: HP HP Laptop 17-by0xxx/84CA, BIOS F.66 03/29/2022 [ 1671.041012] Workqueue: hci0 hci_cmd_sync_work [bluetooth] [ 1671.041194] Call Trace: [ 1671.041200] <TASK> [ 1671.041208] dump_stack_lvl+0x38/0x4d [ 1671.041227] dump_stack+0x10/0x16 [ 1671.041241] hci_req_add+0x47/0x70 [bluetooth] [ 1671.041408] msft_set_filter_enable+0x59/0x90 [bluetooth] [ 1671.041579] msft_do_open+0x131/0x220 [bluetooth] [ 1671.041683] hci_dev_open_sync+0x646/0xc20 [bluetooth] [ 1671.041787] hci_set_powered_sync+0xd4/0x240 [bluetooth] [ 1671.041887] set_powered_sync+0x20/0x60 [bluetooth] [ 1671.041975] hci_cmd_sync_work+0xa8/0x150 [bluetooth] [ 1671.042079] process_one_work+0x21f/0x3f0 [ 1671.042092] worker_thread+0x4a/0x3c0 [ 1671.042102] ? process_one_work+0x3f0/0x3f0 [ 1671.042111] kthread+0xff/0x130 [ 1671.042119] ? kthread_complete_and_exit+0x20/0x20 [ 1671.042128] ret_from_fork+0x22/0x30 [ 1671.042142] </TASK>
Quoted 5 lines
My hardware: HP laptop 17-by0001nw, device is a Realtek combo card:
"Realtek RTL8822BE 802.11 ac 2×2 WiFi + Bluetooth 4.2 Combo Adapter (MU-MIMO supported)"
I am ready to provide additional information and testing, if need be.
@Gix, Brian Can you give a look, we should probably convert the msft_set_filter_enable to use the cmd_sync instead.
Quoted 4 lines
Greetings,
Mateusz Jończyk
Signature · 1 line
Luiz Augusto von Dentz
Quoted 29 lines · Luiz Augusto von Dentz
Quoted 27 lines · Mateusz Jończyk
On 6.1.0-rc3, I have been seeing this error message in dmesg:
Bluetooth: hci0: HCI_REQ-0xfcf0
It is printed on every boot, resume from suspend and rfkill unblock of the Bluetooth device.
The device seems to be functioning normally though (but I have done limited testing only).After some investigation, it turned out to be caused by commit
dd50a864ffae("Bluetooth: Delete unreferencedhci_requestcode")
which modifiedhci_req_add()innet/bluetooth/hci_request.cto always print an error message
when that function is executed.I have added
dump_stack()tohci_req_add()and got the following backtraces:On boot:
[ 18.487766] Bluetooth: hci0: RTL: fw version
0xab6b705c[ 18.548951] Bluetooth: hci0: HCI_REQ-0xfcf0
[ 18.548961] CPU: 3 PID: 108 Comm: kworker/u9:0 Not tainted 6.1.0-rc3unif4-00001-gb33a0948e932 #86
...
Quoted 4 lines
Quoted 4 lines
on rfkill unblock:
[ 1671.040970] Bluetooth: hci0: HCI_REQ-0xfcf0 [ 1671.040992] CPU: 3 PID: 5006 Comm: kworker/u9:2 Not tainted
...
Quoted 10 lines
Quoted 7 lines
My hardware: HP laptop 17-by0001nw, device is a Realtek combo card:
"Realtek RTL8822BE 802.11 ac 2×2 WiFi + Bluetooth 4.2 Combo Adapter (MU-MIMO supported)"
I am ready to provide additional information and testing, if need be.
@Gix, Brian Can you give a look, we should probably convert the
msft_set_filter_enableto use thecmd_syncinstead.
This, I suspect, will be an ongoing issue, particularily with Vender Opcodes, which we don't have much direct visability and testing capabilities. The error gets logged because it is using a deprecated (but still working) mechanism to issue HCI opcodes.
If I can get the source code path of the call as it is being contructed, I can try making you a patch Mateusz... But you will probably need to do the testing/verification for me.
Quoted 4 lines
Quoted 4 lines
Greetings,
Mateusz Jończyk
--Brian
W dniu 31.10.2022 o 22:08, Gix, Brian pisze:
Quoted 18 lines · Luiz Augusto von Dentz
Quoted 17 lines
Quoted 15 lines · Mateusz Jończyk
On 6.1.0-rc3, I have been seeing this error message in dmesg:
Bluetooth: hci0: HCI_REQ-0xfcf0
It is printed on every boot, resume from suspend and rfkill unblock of the Bluetooth device.
The device seems to be functioning normally though (but I have done limited testing only).After some investigation, it turned out to be caused by commit
dd50a864ffae("Bluetooth: Delete unreferencedhci_requestcode")
which modifiedhci_req_add()innet/bluetooth/hci_request.cto always print an error message
when that function is executed.
[...]
Quoted 8 lines
This, I suspect, will be an ongoing issue, particularily with Vender Opcodes, which we don't have much direct visability and testing capabilities. The error gets logged because it is using a deprecated (but still working) mechanism to issue HCI opcodes.
If I can get the source code path of the call as it is being contructed, I can try making you a patch Mateusz... But you will probably need to do the testing/verification for me.
Sure, what info would you like me to provide? The MSFT Vendor Opcode 0xFCF0 is defined in drivers/bluetooth/btrtl.c, line 725.
I'm not sure if I have any additional Bluetooth LE devices around, unfortunately.
Additionally, I think that the error message is a bit cryptic, and perhaps could be changed and/or demoted to a notice for kernel 6.1.
Greetings,
Mateusz