remoteproc: k3-r5: Fix driver shutdown
Subsystems (2)
PATCH 1/1 remoteproc: k3-r5: Fix driver shutdown
From: Jan Kiszka <[email protected]>
When k3_r5_cluster_rproc_exit is run, core 1 is shutdown and removed first. When core 0 should then be stopped before its removal, it will find core1->rproc as NULL already and crashes. Happens on rmmod e.g.
---
There might be one more because I can still make this driver crash after an operator error. Were error scenarios tested at all?
drivers/remoteproc/ti_k3_r5_remoteproc.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/remoteproc/ti_k3_r5_remoteproc.c +2 -1
@@ -646,7 +646,8 @@ static int k3_r5_rproc_stop(struct rproc *rproc)/* do not allow core 0 to stop before core 1 */ core1 = list_last_entry(&cluster->cores, struct k3_r5_core, elem); -if (core != core1 && core1->rproc->state !=RPROC_OFFLINE ) { +if (core != core1 && core1->rproc && + core1->rproc->state !=RPROC_OFFLINE ) {dev_err (dev,"%s: can not stop core 0 before core 1\n" , __func__); ret = -EPERM ;
Signature · 1 line
2.43.0
Hi Jan,
Quoted 5 lines · Jan Kiszka
From: Jan Kiszka <[email protected]>
When
k3_r5_cluster_rproc_exitis run, core 1 is shutdown and removed first. When core 0 should then be stopped before its removal, it will findcore1->rprocas NULL already and crashes. Happens on rmmod e.g.
Did you check this on top of -next-20240820 tag? There was a series[0] which was merged recently which fixed this condition. I don't see this issue when trying on top of -next-20240820 tag. [0]: https://lore.kernel.org/all/[email protected]/
Quoted 8 lines
Fixes 3c8a9066d584 ("remoteproc: k3-r5: Do not allow core1 to power up before core0 via sysfs")Signed-off-by Jan Kiszka <[email protected]>---
There might be one more because I can still make this driver crash after an operator error. Were error scenarios tested at all?
Can you point out what is this issue more specifically, and I can take this up then.
Quoted 18 lines
drivers/remoteproc/ti_k3_r5_remoteproc.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)drivers/remoteproc/ti_k3_r5_remoteproc.c +2
-1@@ -646,7 +646,8 @@ static int k3_r5_rproc_stop(struct rproc *rproc)/* do not allow core 0 to stop before core 1 */ core1 = list_last_entry(&cluster->cores, struct k3_r5_core, elem); -if (core != core1 && core1->rproc->state !=RPROC_OFFLINE ) { +if (core != core1 && core1->rproc && + core1->rproc->state !=RPROC_OFFLINE ) {dev_err (dev,"%s: can not stop core 0 before core 1\n" , __func__); ret = -EPERM ;
Quoted 10 lines · Beleswar Prasad Padhi
Hi Jan,
Quoted 5 lines · Jan Kiszka
From: Jan Kiszka <[email protected]>
When
k3_r5_cluster_rproc_exitis run, core 1 is shutdown and removed first. When core 0 should then be stopped before its removal, it will findcore1->rprocas NULL already and crashes. Happens on rmmod e.g.
Quoted 5 lines
Did you check this on top of -next-20240820 tag? There was a series[0] which was merged recently which fixed this condition. I don't see this issue when trying on top of -next-20240820 tag.
[0]: https://lore.kernel.org/all/[email protected]/
I didn't try those yet, I was on 6.11-rcX. But from reading them quickly, I'm not seeing the two issues I found directly addressed there.
Quoted 7 lines
Quoted 7 lines
Fixes 3c8a9066d584 ("remoteproc: k3-r5: Do not allow core1 to powerup before core0 via sysfs")
Signed-off-by Jan Kiszka <[email protected]>---
Quoted 6 lines
Quoted 2 lines
There might be one more because I can still make this driver crash after an operator error. Were error scenarios tested at all?
Can you point out what is this issue more specifically, and I can take this up then.
Try starting core1 before core0, and then again - system will hang or crash while trying to wipe ATCM. I do not understand this problem yet - same VA is used, and I cannot see where/how the region should have been unmapped in between.
Jan
Quoted 20 lines
Quoted 20 lines
drivers/remoteproc/ti_k3_r5_remoteproc.c| 3 ++-1 file changed, 2 insertions(+), 1 deletion(-)drivers/remoteproc/ti_k3_r5_remoteproc.c +2
-1@@ -646,7 +646,8 @@ static int k3_r5_rproc_stop(struct rproc *rproc) /* do not allow core 0 to stop before core 1 */ core1 = list_last_entry(&cluster->cores, struct k3_r5_core, elem); - if (core != core1 && core1->rproc->state != RPROC_OFFLINE) { + if (core != core1 && core1->rproc && + core1->rproc->state != RPROC_OFFLINE) { dev_err(dev, "%s: can not stop core 0 before core 1\n", __func__); ret = -EPERM;
Signature · 2 lines
Siemens AG, Technology Linux Expert Center
Quoted 10 lines · Jan Kiszka
Quoted 9 lines · Beleswar Prasad Padhi
Hi Jan,
Quoted 5 lines · Jan Kiszka
From: Jan Kiszka <[email protected]>
When
k3_r5_cluster_rproc_exitis run, core 1 is shutdown and removed first. When core 0 should then be stopped before its removal, it will findcore1->rprocas NULL already and crashes. Happens on rmmod e.g.
Quoted 7 lines
Quoted 5 lines
Did you check this on top of -next-20240820 tag? There was a series[0] which was merged recently which fixed this condition. I don't see this issue when trying on top of -next-20240820 tag.
[0]: https://lore.kernel.org/all/[email protected]/I didn't try those yet, I was on 6.11-rcX. But from reading them quickly, I'm not seeing the two issues I found directly addressed there.
Check the comment by Andrew Davis[0], that addresses the above issue.
[0]: https://lore.kernel.org/all/[email protected]/
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
Fixes 3c8a9066d584 ("remoteproc: k3-r5: Do not allow core1 to powerup before core0 via sysfs")
Signed-off-by Jan Kiszka <[email protected]>---
Quoted 6 lines
Quoted 5 lines
Quoted 2 lines
There might be one more because I can still make this driver crash after an operator error. Were error scenarios tested at all?
Can you point out what is this issue more specifically, and I can take this up then.
Try starting core1 before core0, and then again - system will hang or
If you are trying to stop and then start the cores from sysfs, that is not yet supported. The hang is thus expected.
Quoted 24 lines
crash while trying to wipe ATCM. I do not understand this problem yet - same VA is used, and I cannot see where/how the region should have been unmapped in between.
Jan
Quoted 18 lines
Quoted 18 lines
drivers/remoteproc/ti_k3_r5_remoteproc.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)drivers/remoteproc/ti_k3_r5_remoteproc.c +2
-1@@ -646,7 +646,8 @@ static int k3_r5_rproc_stop(struct rproc *rproc) /* do not allow core 0 to stop before core 1 */ core1 = list_last_entry(&cluster->cores, struct k3_r5_core, elem); - if (core != core1 && core1->rproc->state != RPROC_OFFLINE) { + if (core != core1 && core1->rproc && + core1->rproc->state != RPROC_OFFLINE) { dev_err(dev, "%s: can not stop core 0 before core 1\n", __func__); ret = -EPERM;
Quoted 18 lines · Beleswar Prasad Padhi
Quoted 16 lines · Jan Kiszka
Quoted 15 lines · Beleswar Prasad Padhi
Hi Jan,
Quoted 5 lines · Jan Kiszka
From: Jan Kiszka <[email protected]>
When
k3_r5_cluster_rproc_exitis run, core 1 is shutdown and removed first. When core 0 should then be stopped before its removal, it will findcore1->rprocas NULL already and crashes. Happens on rmmod e.g.Did you check this on top of -next-20240820 tag? There was a series[0] which was merged recently which fixed this condition. I don't see this issue when trying on top of -next-20240820 tag.
[0]:
https://lore.kernel.org/all/[email protected]/
Quoted 8 lines
Quoted 2 lines
I didn't try those yet, I was on 6.11-rcX. But from reading them quickly, I'm not seeing the two issues I found directly addressed there.
Check the comment by Andrew Davis[0], that addresses the above issue.
OK, then someone still needs to update his patch accordingly.
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
Fixes 3c8a9066d584 ("remoteproc: k3-r5: Do not allow core1 to powerup before core0 via sysfs")
Signed-off-by Jan Kiszka <[email protected]>---
Quoted 8 lines
Quoted 6 lines
Quoted 5 lines
Quoted 2 lines
There might be one more because I can still make this driver crash after an operator error. Were error scenarios tested at all?
Can you point out what is this issue more specifically, and I can take this up then.
Try starting core1 before core0, and then again - system will hang or
If you are trying to stop and then start the cores from sysfs, that is not yet supported. The hang is thus expected.
What? Then the driver is broken, even more. Why wasn't it fully implemented?
Jan
Signature · 2 lines
Siemens AG, Technology Linux Expert Center
Quoted 17 lines · Jan Kiszka
Quoted 16 lines · Beleswar Prasad Padhi
Quoted 15 lines · Jan Kiszka
Quoted 14 lines · Beleswar Prasad Padhi
Hi Jan,
Quoted 5 lines · Jan Kiszka
From: Jan Kiszka <[email protected]>
When
k3_r5_cluster_rproc_exitis run, core 1 is shutdown and removed first. When core 0 should then be stopped before its removal, it will findcore1->rprocas NULL already and crashes. Happens on rmmod e.g.Did you check this on top of -next-20240820 tag? There was a series[0] which was merged recently which fixed this condition. I don't see this issue when trying on top of -next-20240820 tag.
[0]:
https://lore.kernel.org/all/[email protected]/
Quoted 8 lines
Quoted 7 lines
Quoted 2 lines
I didn't try those yet, I was on 6.11-rcX. But from reading them quickly, I'm not seeing the two issues I found directly addressed there.
Check the comment by Andrew Davis[0], that addresses the above issue.
OK, then someone still needs to update his patch accordingly.
That comment was addressed in the v4 series revision[1] and was merged to linux-next, available with tag -next-20240820. Request you to please check if the issue persists with -next-20240820 tag. I checked myself, and was not able to reproduce. [1]: https://lore.kernel.org/all/Zr9nbWnADDB+ZOlg@p14s/
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
Fixes 3c8a9066d584 ("remoteproc: k3-r5: Do not allow core1 to powerup before core0 via sysfs")
Signed-off-by Jan Kiszka <[email protected]>---
Quoted 8 lines
Quoted 7 lines
Quoted 5 lines
Quoted 4 lines
Quoted 2 lines
There might be one more because I can still make this driver crash after an operator error. Were error scenarios tested at all?
Can you point out what is this issue more specifically, and I can take this up then.
Try starting core1 before core0, and then again - system will hang or
If you are trying to stop and then start the cores from sysfs, that is not yet supported. The hang is thus expected.
What? Then the driver is broken, even more. Why wasn't it fully implemented?
The driver is capable of starting a core and stopping it all well. The problem is, when we stop a core from sysfs (without resetting the SoC itself), the remotecore is powered off, but its resources are not relinquished. So when we start it back, there could be some memory corruptions. This feature of "graceful shutdown" of remotecores is almost implemented and will be posted to this driver soon. Request you to try out after that.
With graceful shutdown feature, this will be the flow:
1. We issue a core stop operation from sysfs.
2. The remoteproc driver sends a special "SHUTDOWN" mailbox message to the remotecore.
3. The remotecore relinquishes all of its acquired resources through Device Manager Firmware and sends an ACK back.
4. The remotecore enters WFI state and then is resetted through Host core.
5. Then, if we try to do the core start operation from sysfs, core should be up as expected.
Thanks,
Beleswar
Quoted 3 lines
Jan
Quoted 23 lines · Beleswar Prasad Padhi
Quoted 21 lines · Jan Kiszka
Quoted 20 lines · Beleswar Prasad Padhi
Quoted 9 lines · Jan Kiszka
Quoted 8 lines · Beleswar Prasad Padhi
Hi Jan,
Quoted 5 lines · Jan Kiszka
From: Jan Kiszka <[email protected]>
When
k3_r5_cluster_rproc_exitis run, core 1 is shutdown and removed first. When core 0 should then be stopped before its removal, it will findcore1->rprocas NULL already and crashes. Happens on rmmod e.g.Quoted 8 lines
Quoted 6 lines
Did you check this on top of -next-20240820 tag? There was a series[0] which was merged recently which fixed this condition. I don't see this issue when trying on top of -next-20240820 tag.
[0]:
https://lore.kernel.org/all/[email protected]/I didn't try those yet, I was on 6.11-rcX. But from reading them quickly, I'm not seeing the two issues I found directly addressed there.
Check the comment by Andrew Davis[0], that addresses the above issue.
Quoted 22 lines
Quoted 5 lines
Quoted 4 lines
OK, then someone still needs to update his patch accordingly.
That comment was addressed in the v4 series revision[1] and was merged to linux-next, available with tag -next-20240820. Request you to please check if the issue persists with -next-20240820 tag. I checked myself, and was not able to reproduce. [1]: https://lore.kernel.org/all/Zr9nbWnADDB+ZOlg@p14s/
Quoted 15 lines
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
Fixes 3c8a9066d584 ("remoteproc: k3-r5: Do not allow core1 to powerup before core0 via sysfs")
Signed-off-by Jan Kiszka <[email protected]>---
Quoted 7 lines
Quoted 5 lines
Quoted 4 lines
Quoted 2 lines
There might be one more because I can still make this driver crash after an operator error. Were error scenarios tested at all?
Can you point out what is this issue more specifically, and I can take this up then.
Try starting core1 before core0, and then again - system will hang or
If you are trying to stop and then start the cores from sysfs, that is not yet supported. The hang is thus expected.
What? Then the driver is broken, even more. Why wasn't it fully implemented?
Just wanted to point out that this "graceful shutdown" feature is majorly dependent on the Device Manager Firmware(point 3) and minimal changes to the remoteproc driver (point 2 and 4). Thus, as soon as Firmware is capable, we will send out the patches for this feature.
Quoted 14 lines
The driver is capable of starting a core and stopping it all well. The problem is, when we stop a core from sysfs (without resetting the SoC itself), the remotecore is powered off, but its resources are not relinquished. So when we start it back, there could be some memory corruptions. This feature of "graceful shutdown" of remotecores is almost implemented and will be posted to this driver soon. Request you to try out after that.
With graceful shutdown feature, this will be the flow:
1. We issue a core stop operation from sysfs.
2. The remoteproc driver sends a special "SHUTDOWN" mailbox message to the remotecore.
3. The remotecore relinquishes all of its acquired resources through Device Manager Firmware and sends an ACK back.
4. The remotecore enters WFI state and then is resetted through Host core.
5. Then, if we try to do the core start operation from sysfs, core should be up as expected.Thanks,
BeleswarQuoted 3 lines
Jan