e1000e: Add handshake with the CSME to support s0ix
Subsystems (2)
PATCH 1/3 e1000e: Add handshake with the CSME to support s0ix
On the corporate system, the driver will ask from the CSME (manageability engine) to perform device settings are required to allow s0ix residency.
This patch provides initial support.
--- drivers/net/ethernet/intel/e1000e/ich8lan.h | 2 + drivers/net/ethernet/intel/e1000e/netdev.c | 328 +++++++++++--------- 2 files changed, 176 insertions(+), 154 deletions(-)
drivers/net/ethernet/intel/e1000e/ich8lan.h +2 -0
@@ -47,6 +47,8 @@#define E1000_SHRAH_PCH_LPT (_i) (0x0540C + ((_i) * 8))#define E1000_H2ME 0x05B50/* Host to ME */ +#define E1000_H2ME_START_DPG 0x00000001/* indicate the ME of DPG */ +#define E1000_H2ME_EXIT_DPG 0x00000002/* indicate the ME exit DPG */ #define E1000_H2ME_ULP 0x00000800/* ULP Indication Bit */ #define E1000_H2ME_ENFORCE_SETTINGS 0x00001000/* Enforce Settings */
drivers/net/ethernet/intel/e1000e/netdev.c +174 -154
362 lines not on this page · raw message
Signature · 1 line
2.25.1
PATCH 1/3 e1000e: Add handshake with the CSME to support s0ix
Dear Sasha,
Am 24.06.21 um 10:18 schrieb Sasha Neftin:
Quoted 4 lines
On the corporate system, the driver will ask from the CSME (manageability engine) to perform device settings are required to allow s0ix residency.
This patch provides initial support.
Please give more details, and list the (public) datasheets documenting this procedure.
As this has caused problems in the past, please document the performed tests (including used devices and firmware versions) in detail in the commit message.
Kind regards,
Paul
Quoted 390 lines
Reviewed-by Dima Ruinskiy <[email protected]>Signed-off-by Sasha Neftin <[email protected]>--- drivers/net/ethernet/intel/e1000e/ich8lan.h | 2 + drivers/net/ethernet/intel/e1000e/netdev.c | 328 +++++++++++--------- 2 files changed, 176 insertions(+), 154 deletions(-)drivers/net/ethernet/intel/e1000e/ich8lan.h +2
-0@@ -47,6 +47,8 @@#define E1000_SHRAH_PCH_LPT (_i) (0x0540C + ((_i) * 8))#define E1000_H2ME 0x05B50/* Host to ME */ +#define E1000_H2ME_START_DPG 0x00000001/* indicate the ME of DPG */ +#define E1000_H2ME_EXIT_DPG 0x00000002/* indicate the ME exit DPG */ #define E1000_H2ME_ULP 0x00000800/* ULP Indication Bit */ #define E1000_H2ME_ENFORCE_SETTINGS 0x00001000/* Enforce Settings */ drivers/net/ethernet/intel/e1000e/netdev.c +174
-154@@ -6345,42 +6345,104 @@ static void e1000e_s0ix_entry_flow(struct e1000_adapter *adapter)u32 mac_data;u16 phy_data; -/* Disable the periodic inband message, -* don't request PCIe clock in K1 page770_17[10:9] = 10b -*/ -e1e_rphy (hw,HV_PM_CTRL , &phy_data); - phy_data &= ~HV_PM_CTRL_K1_CLK_REQ ; - phy_data |=BIT (10 ); -e1e_wphy (hw,HV_PM_CTRL , phy_data); +if (er32 (FWSM ) &E1000_ICH_FWSM_FW_VALID ) { +/* Request ME configure the device for s0ix */ + mac_data =er32 (H2ME ); + mac_data |=E1000_H2ME_START_DPG ; + mac_data &= ~E1000_H2ME_EXIT_DPG ; +ew32 (H2ME , mac_data); + }else { +/* Request driver configure the device to s0ix */ +/* Disable the periodic inband message, +* don't request PCIe clock in K1 page770_17[10:9] = 10b +*/ +e1e_rphy (hw,HV_PM_CTRL , &phy_data); + phy_data &= ~HV_PM_CTRL_K1_CLK_REQ ; + phy_data |=BIT (10 ); +e1e_wphy (hw,HV_PM_CTRL , phy_data); -/* Make sure we don't exit K1 every time a new packet arrives -* 772_29[5] = 1 CS_Mode_Stay_In_K1 -*/ -e1e_rphy (hw,I217_CGFREG , &phy_data); - phy_data |=BIT (5 ); -e1e_wphy (hw,I217_CGFREG , phy_data); +/* Make sure we don't exit K1 every time a new packet arrives +* 772_29[5] = 1 CS_Mode_Stay_In_K1 +*/ +e1e_rphy (hw,I217_CGFREG , &phy_data); + phy_data |=BIT (5 ); +e1e_wphy (hw,I217_CGFREG , phy_data); -/* Change the MAC/PHY interface to SMBus -* Force the SMBus in PHY page769_23[0] = 1 -* Force the SMBus in MAC CTRL_EXT[11] = 1 -*/ -e1e_rphy (hw,CV_SMB_CTRL , &phy_data); - phy_data |=CV_SMB_CTRL_FORCE_SMBUS ; -e1e_wphy (hw,CV_SMB_CTRL , phy_data); - mac_data =er32 (CTRL_EXT ); - mac_data |=E1000_CTRL_EXT_FORCE_SMBUS ; -ew32 (CTRL_EXT , mac_data); +/* Change the MAC/PHY interface to SMBus +* Force the SMBus in PHY page769_23[0] = 1 +* Force the SMBus in MAC CTRL_EXT[11] = 1 +*/ +e1e_rphy (hw,CV_SMB_CTRL , &phy_data); + phy_data |=CV_SMB_CTRL_FORCE_SMBUS ; +e1e_wphy (hw,CV_SMB_CTRL , phy_data); + mac_data =er32 (CTRL_EXT ); + mac_data |=E1000_CTRL_EXT_FORCE_SMBUS ; +ew32 (CTRL_EXT , mac_data); + +/* DFT control: PHY bit: page769_20[0] = 1 +* Gate PPW via EXTCNF_CTRL - set 0x0F00[7] = 1 +*/ +e1e_rphy (hw,I82579_DFT_CTRL , &phy_data); + phy_data |=BIT (0 ); +e1e_wphy (hw,I82579_DFT_CTRL , phy_data); + + mac_data =er32 (EXTCNF_CTRL ); + mac_data |=E1000_EXTCNF_CTRL_GATE_PHY_CFG ; +ew32 (EXTCNF_CTRL , mac_data); + +/* Enable the Dynamic Power Gating in the MAC */ + mac_data =er32 (FEXTNVM7 ); + mac_data |=BIT (22 ); +ew32 (FEXTNVM7 , mac_data); + +/* Disable disconnected cable conditioning for Power Gating */ + mac_data =er32 (DPGFR ); + mac_data |=BIT (2 ); +ew32 (DPGFR , mac_data); + +/* Don't wake from dynamic Power Gating with clock request */ + mac_data =er32 (FEXTNVM12 ); + mac_data |=BIT (12 ); +ew32 (FEXTNVM12 , mac_data); + +/* Ungate PGCB clock */ + mac_data =er32 (FEXTNVM9 ); + mac_data &= ~BIT (28 ); +ew32 (FEXTNVM9 , mac_data); + +/* Enable K1 off to enable mPHY Power Gating */ + mac_data =er32 (FEXTNVM6 ); + mac_data |=BIT (31 ); +ew32 (FEXTNVM6 , mac_data); + +/* Enable mPHY power gating for any link and speed */ + mac_data =er32 (FEXTNVM8 ); + mac_data |=BIT (9 ); +ew32 (FEXTNVM8 , mac_data); + +/* Enable the Dynamic Clock Gating in the DMA and MAC */ + mac_data =er32 (CTRL_EXT ); + mac_data |=E1000_CTRL_EXT_DMA_DYN_CLK_EN ; +ew32 (CTRL_EXT , mac_data); + +/* No MAC DPG gating SLP_S0 in modern standby +* Switch the logic of the lanphypc to use PMC counter +*/ + mac_data =er32 (FEXTNVM5 ); + mac_data |=BIT (7 ); +ew32 (FEXTNVM5 , mac_data); + } -/* DFT control: PHY bit: page769_20[0] = 1 -* Gate PPW via EXTCNF_CTRL - set 0x0F00[7] = 1 -*/ -e1e_rphy (hw,I82579_DFT_CTRL , &phy_data); - phy_data |=BIT (0 ); -e1e_wphy (hw,I82579_DFT_CTRL , phy_data); +/* Disable the time synchronization clock */ + mac_data =er32 (FEXTNVM7 ); + mac_data |=BIT (31 ); + mac_data &= ~BIT (0 ); +ew32 (FEXTNVM7 , mac_data); - mac_data =er32 (EXTCNF_CTRL ); - mac_data |=E1000_EXTCNF_CTRL_GATE_PHY_CFG ; -ew32 (EXTCNF_CTRL , mac_data); +/* Dynamic Power Gating Enable */ + mac_data =er32 (CTRL_EXT ); + mac_data |=BIT (3 ); +ew32 (CTRL_EXT , mac_data);/* Check MAC Tx/Rx packet buffer pointers. * Reset MAC Tx/Rx packet buffer pointers to suppress any @@ -6416,59 +6478,6 @@ static void e1000e_s0ix_entry_flow(struct e1000_adapter *adapter) mac_data =er32 (RDFPC );if (mac_data)ew32 (RDFPC ,0 ); - -/* Enable the Dynamic Power Gating in the MAC */ - mac_data =er32 (FEXTNVM7 ); - mac_data |=BIT (22 ); -ew32 (FEXTNVM7 , mac_data); - -/* Disable the time synchronization clock */ - mac_data =er32 (FEXTNVM7 ); - mac_data |=BIT (31 ); - mac_data &= ~BIT (0 ); -ew32 (FEXTNVM7 , mac_data); - -/* Dynamic Power Gating Enable */ - mac_data =er32 (CTRL_EXT ); - mac_data |=BIT (3 ); -ew32 (CTRL_EXT , mac_data); - -/* Disable disconnected cable conditioning for Power Gating */ - mac_data =er32 (DPGFR ); - mac_data |=BIT (2 ); -ew32 (DPGFR , mac_data); - -/* Don't wake from dynamic Power Gating with clock request */ - mac_data =er32 (FEXTNVM12 ); - mac_data |=BIT (12 ); -ew32 (FEXTNVM12 , mac_data); - -/* Ungate PGCB clock */ - mac_data =er32 (FEXTNVM9 ); - mac_data &= ~BIT (28 ); -ew32 (FEXTNVM9 , mac_data); - -/* Enable K1 off to enable mPHY Power Gating */ - mac_data =er32 (FEXTNVM6 ); - mac_data |=BIT (31 ); -ew32 (FEXTNVM6 , mac_data); - -/* Enable mPHY power gating for any link and speed */ - mac_data =er32 (FEXTNVM8 ); - mac_data |=BIT (9 ); -ew32 (FEXTNVM8 , mac_data); - -/* Enable the Dynamic Clock Gating in the DMA and MAC */ - mac_data =er32 (CTRL_EXT ); - mac_data |=E1000_CTRL_EXT_DMA_DYN_CLK_EN ; -ew32 (CTRL_EXT , mac_data); - -/* No MAC DPG gating SLP_S0 in modern standby -* Switch the logic of the lanphypc to use PMC counter -*/ - mac_data =er32 (FEXTNVM5 ); - mac_data |=BIT (7 ); -ew32 (FEXTNVM5 , mac_data); }static void e1000e_s0ix_exit_flow (struct e1000_adapter *adapter)@@ -6477,87 +6486,98 @@ static void e1000e_s0ix_exit_flow(struct e1000_adapter *adapter)u32 mac_data;u16 phy_data; -/* Disable the Dynamic Power Gating in the MAC */ - mac_data =er32 (FEXTNVM7 ); - mac_data &=0xFFBFFFFF ; -ew32 (FEXTNVM7 , mac_data); +if (er32 (FWSM ) &E1000_ICH_FWSM_FW_VALID ) { +/* Request ME un configure the device from s0ix */ + mac_data =er32 (H2ME ); + mac_data &= ~E1000_H2ME_START_DPG ; + mac_data |=E1000_H2ME_EXIT_DPG ; +ew32 (H2ME , mac_data); + }else { +/* Request driver un configure the device from s0ix */ + +/* Disable the Dynamic Power Gating in the MAC */ + mac_data =er32 (FEXTNVM7 ); + mac_data &=0xFFBFFFFF ; +ew32 (FEXTNVM7 , mac_data); + +/* Disable mPHY power gating for any link and speed */ + mac_data =er32 (FEXTNVM8 ); + mac_data &= ~BIT (9 ); +ew32 (FEXTNVM8 , mac_data); + +/* Disable K1 off */ + mac_data =er32 (FEXTNVM6 ); + mac_data &= ~BIT (31 ); +ew32 (FEXTNVM6 , mac_data); + +/* Disable Ungate PGCB clock */ + mac_data =er32 (FEXTNVM9 ); + mac_data |=BIT (28 ); +ew32 (FEXTNVM9 , mac_data); + +/* Cancel not waking from dynamic +* Power Gating with clock request +*/ + mac_data =er32 (FEXTNVM12 ); + mac_data &= ~BIT (12 ); +ew32 (FEXTNVM12 , mac_data); -/* Enable the time synchronization clock */ - mac_data =er32 (FEXTNVM7 ); - mac_data |=BIT (0 ); -ew32 (FEXTNVM7 , mac_data); +/* Cancel disable disconnected cable conditioning +* for Power Gating +*/ + mac_data =er32 (DPGFR ); + mac_data &= ~BIT (2 ); +ew32 (DPGFR , mac_data); -/* Disable mPHY power gating for any link and speed */ - mac_data =er32 (FEXTNVM8 ); - mac_data &= ~BIT (9 ); -ew32 (FEXTNVM8 , mac_data); +/* Disable the Dynamic Clock Gating in the DMA and MAC */ + mac_data =er32 (CTRL_EXT ); + mac_data &=0xFFF7FFFF ; +ew32 (CTRL_EXT , mac_data); -/* Disable K1 off */ - mac_data =er32 (FEXTNVM6 ); - mac_data &= ~BIT (31 ); -ew32 (FEXTNVM6 , mac_data); +/* Revert the lanphypc logic to use the internal Gbe counter +* and not the PMC counter +*/ + mac_data =er32 (FEXTNVM5 ); + mac_data &=0xFFFFFF7F ; +ew32 (FEXTNVM5 , mac_data); -/* Disable Ungate PGCB clock */ - mac_data =er32 (FEXTNVM9 ); - mac_data |=BIT (28 ); -ew32 (FEXTNVM9 , mac_data); +/* Enable the periodic inband message, +* Request PCIe clock in K1 page770_17[10:9] =01b +*/ +e1e_rphy (hw,HV_PM_CTRL , &phy_data); + phy_data &=0xFBFF ; + phy_data |=HV_PM_CTRL_K1_CLK_REQ ; +e1e_wphy (hw,HV_PM_CTRL , phy_data); -/* Cancel not waking from dynamic -* Power Gating with clock request -*/ - mac_data =er32 (FEXTNVM12 ); - mac_data &= ~BIT (12 ); -ew32 (FEXTNVM12 , mac_data); +/* Return back configuration +* 772_29[5] = 0 CS_Mode_Stay_In_K1 +*/ +e1e_rphy (hw,I217_CGFREG , &phy_data); + phy_data &=0xFFDF ; +e1e_wphy (hw,I217_CGFREG , phy_data); -/* Cancel disable disconnected cable conditioning -* for Power Gating -*/ - mac_data =er32 (DPGFR ); - mac_data &= ~BIT (2 ); -ew32 (DPGFR , mac_data); +/* Change the MAC/PHY interface to Kumeran +* Unforce the SMBus in PHY page769_23[0] = 0 +* Unforce the SMBus in MAC CTRL_EXT[11] = 0 +*/ +e1e_rphy (hw,CV_SMB_CTRL , &phy_data); + phy_data &= ~CV_SMB_CTRL_FORCE_SMBUS ; +e1e_wphy (hw,CV_SMB_CTRL , phy_data); + mac_data =er32 (CTRL_EXT ); + mac_data &= ~E1000_CTRL_EXT_FORCE_SMBUS ; +ew32 (CTRL_EXT , mac_data); + }/* Disable Dynamic Power Gating */ mac_data =er32 (CTRL_EXT ); mac_data &=0xFFFFFFF7 ;ew32 (CTRL_EXT , mac_data); -/* Disable the Dynamic Clock Gating in the DMA and MAC */ - mac_data =er32 (CTRL_EXT ); - mac_data &=0xFFF7FFFF ; -ew32 (CTRL_EXT , mac_data); - -/* Revert the lanphypc logic to use the internal Gbe counter -* and not the PMC counter -*/ - mac_data =er32 (FEXTNVM5 ); - mac_data &=0xFFFFFF7F ; -ew32 (FEXTNVM5 , mac_data); - -/* Enable the periodic inband message, -* Request PCIe clock in K1 page770_17[10:9] =01b -*/ -e1e_rphy (hw,HV_PM_CTRL , &phy_data); - phy_data &=0xFBFF ; - phy_data |=HV_PM_CTRL_K1_CLK_REQ ; -e1e_wphy (hw,HV_PM_CTRL , phy_data); - -/* Return back configuration -* 772_29[5] = 0 CS_Mode_Stay_In_K1 -*/ -e1e_rphy (hw,I217_CGFREG , &phy_data); - phy_data &=0xFFDF ; -e1e_wphy (hw,I217_CGFREG , phy_data); - -/* Change the MAC/PHY interface to Kumeran -* Unforce the SMBus in PHY page769_23[0] = 0 -* Unforce the SMBus in MAC CTRL_EXT[11] = 0 -*/ -e1e_rphy (hw,CV_SMB_CTRL , &phy_data); - phy_data &= ~CV_SMB_CTRL_FORCE_SMBUS ; -e1e_wphy (hw,CV_SMB_CTRL , phy_data); - mac_data =er32 (CTRL_EXT ); - mac_data &= ~E1000_CTRL_EXT_FORCE_SMBUS ; -ew32 (CTRL_EXT , mac_data); +/* Enable the time synchronization clock */ + mac_data =er32 (FEXTNVM7 ); + mac_data &= ~BIT (31 ); + mac_data |=BIT (0 ); +ew32 (FEXTNVM7 , mac_data); }static int e1000e_pm_freeze (struct device *dev)
Neftin
PATCH 1/3 e1000e: Add handshake with the CSME to support s0ix
Quoted 11 lines · Paul Menzel
Dear Sasha,
Am 24.06.21 um 10:18 schrieb Sasha Neftin:
Quoted 4 lines
On the corporate system, the driver will ask from the CSME (manageability engine) to perform device settings are required to allow s0ix residency.
This patch provides initial support.Please give more details, and list the (public) datasheets documenting this procedure.
Agree. I will check with our technical writers how we can process documentation. CSME code is not open source - I need to check how and what we can communicate.
Quoted 5 lines
As this has caused problems in the past, please document the performed tests (including used devices and firmware versions) in detail in the commit message.
We have tested on TGLU platform (I219 LM 15FB 1Gbe controller) with CSME 0:15.0.23.1706. Checked s2idle patch and s0ix residency.
Quoted 377 lines
Kind regards,
Paul
Quoted 371 lines
Reviewed-by Dima Ruinskiy <[email protected]>Signed-off-by Sasha Neftin <[email protected]>---
?drivers/net/ethernet/intel/e1000e/ich8lan.h|?? 2 +
?drivers/net/ethernet/intel/e1000e/netdev.c? | 328 +++++++++++--------- ? 2 files changed, 176 insertions(+), 154 deletions(-)drivers/net/ethernet/intel/e1000e/ich8lan.h +0
-0@@ -47,6 +47,8 @@ ? #define E1000_SHRAH_PCH_LPT(_i)??????? (0x0540C + ((_i) * 8))? #define
E1000_H2ME???????0x05B50??? /* Host to ME */ +#defineE1000_H2ME_START_DPG???0x00000001??? /* indicate the ME of DPG */
+#defineE1000_H2ME_EXIT_DPG???0x00000002??? /* indicate the ME exit DPG */
? #defineE1000_H2ME_ULP???????0x00000800??? /* ULP Indication Bit */ ? #defineE1000_H2ME_ENFORCE_SETTINGS???0x00001000??? /* Enforce Settings */drivers/net/ethernet/intel/e1000e/netdev.c +94
-32@@ -6345,42 +6345,104 @@ static void e1000e_s0ix_entry_flow(struct e1000_adapter *adapter) ????? u32 mac_data; ????? u16 phy_data; -??? /* Disable the periodic inband message, -???? * don't request PCIe clock in K1 page770_17[10:9] = 10b -???? */ -??? e1e_rphy(hw, HV_PM_CTRL, &phy_data); -??? phy_data &= ~HV_PM_CTRL_K1_CLK_REQ; -??? phy_data |= BIT(10); -??? e1e_wphy(hw, HV_PM_CTRL, phy_data); +??? if (er32(FWSM) & E1000_ICH_FWSM_FW_VALID) { +??????? /* Request ME configure the device for s0ix */ +??????? mac_data = er32(H2ME); +??????? mac_data |= E1000_H2ME_START_DPG; +??????? mac_data &= ~E1000_H2ME_EXIT_DPG; +??????? ew32(H2ME, mac_data); +??? } else { +??????? /* Request driver configure the device to s0ix */ +??????? /* Disable the periodic inband message, +???????? * don't request PCIe clock in K1 page770_17[10:9] = 10b +???????? */ +??????? e1e_rphy(hw, HV_PM_CTRL, &phy_data); +??????? phy_data &= ~HV_PM_CTRL_K1_CLK_REQ; +??????? phy_data |= BIT(10); +??????? e1e_wphy(hw, HV_PM_CTRL, phy_data); -??? /* Make sure we don't exit K1 every time a new packet arrives -???? * 772_29[5] = 1 CS_Mode_Stay_In_K1 -???? */ -??? e1e_rphy(hw, I217_CGFREG, &phy_data); -??? phy_data |= BIT(5); -??? e1e_wphy(hw, I217_CGFREG, phy_data); +??????? /* Make sure we don't exit K1 every time a new packet arrives +???????? * 772_29[5] = 1 CS_Mode_Stay_In_K1 +???????? */ +??????? e1e_rphy(hw, I217_CGFREG, &phy_data); +??????? phy_data |= BIT(5); +??????? e1e_wphy(hw, I217_CGFREG, phy_data); -??? /* Change the MAC/PHY interface to SMBus -???? * Force the SMBus in PHY page769_23[0] = 1 -???? * Force the SMBus in MAC CTRL_EXT[11] = 1 -???? */ -??? e1e_rphy(hw, CV_SMB_CTRL, &phy_data); -??? phy_data |= CV_SMB_CTRL_FORCE_SMBUS; -??? e1e_wphy(hw, CV_SMB_CTRL, phy_data); -??? mac_data = er32(CTRL_EXT); -??? mac_data |= E1000_CTRL_EXT_FORCE_SMBUS; -??? ew32(CTRL_EXT, mac_data); +??????? /* Change the MAC/PHY interface to SMBus +???????? * Force the SMBus in PHY page769_23[0] = 1 +???????? * Force the SMBus in MAC CTRL_EXT[11] = 1 +???????? */ +??????? e1e_rphy(hw, CV_SMB_CTRL, &phy_data); +??????? phy_data |= CV_SMB_CTRL_FORCE_SMBUS; +??????? e1e_wphy(hw, CV_SMB_CTRL, phy_data); +??????? mac_data = er32(CTRL_EXT); +??????? mac_data |= E1000_CTRL_EXT_FORCE_SMBUS; +??????? ew32(CTRL_EXT, mac_data); + +??????? /* DFT control: PHY bit: page769_20[0] = 1 +???????? * Gate PPW via EXTCNF_CTRL - set 0x0F00[7] = 1 +???????? */ +??????? e1e_rphy(hw, I82579_DFT_CTRL, &phy_data); +??????? phy_data |= BIT(0); +??????? e1e_wphy(hw, I82579_DFT_CTRL, phy_data); + +??????? mac_data = er32(EXTCNF_CTRL); +??????? mac_data |= E1000_EXTCNF_CTRL_GATE_PHY_CFG; +??????? ew32(EXTCNF_CTRL, mac_data); + +??????? /* Enable the Dynamic Power Gating in the MAC */ +??????? mac_data = er32(FEXTNVM7); +??????? mac_data |= BIT(22); +??????? ew32(FEXTNVM7, mac_data); + +??????? /* Disable disconnected cable conditioning for Power Gating */ +??????? mac_data = er32(DPGFR); +??????? mac_data |= BIT(2); +??????? ew32(DPGFR, mac_data); + +??????? /* Don't wake from dynamic Power Gating with clock request */ +??????? mac_data = er32(FEXTNVM12); +??????? mac_data |= BIT(12); +??????? ew32(FEXTNVM12, mac_data); + +??????? /* Ungate PGCB clock */ +??????? mac_data = er32(FEXTNVM9); +??????? mac_data &= ~BIT(28); +??????? ew32(FEXTNVM9, mac_data); + +??????? /* Enable K1 off to enable mPHY Power Gating */ +??????? mac_data = er32(FEXTNVM6); +??????? mac_data |= BIT(31); +??????? ew32(FEXTNVM6, mac_data); + +??????? /* Enable mPHY power gating for any link and speed */ +??????? mac_data = er32(FEXTNVM8); +??????? mac_data |= BIT(9); +??????? ew32(FEXTNVM8, mac_data); + +??????? /* Enable the Dynamic Clock Gating in the DMA and MAC */ +??????? mac_data = er32(CTRL_EXT); +??????? mac_data |= E1000_CTRL_EXT_DMA_DYN_CLK_EN; +??????? ew32(CTRL_EXT, mac_data); + +??????? /* No MAC DPG gating SLP_S0 in modern standby +???????? * Switch the logic of the lanphypc to use PMC counter +???????? */ +??????? mac_data = er32(FEXTNVM5); +??????? mac_data |= BIT(7); +??????? ew32(FEXTNVM5, mac_data); +??? } -??? /* DFT control: PHY bit: page769_20[0] = 1 -???? * Gate PPW via EXTCNF_CTRL - set 0x0F00[7] = 1 -???? */ -??? e1e_rphy(hw, I82579_DFT_CTRL, &phy_data); -??? phy_data |= BIT(0); -??? e1e_wphy(hw, I82579_DFT_CTRL, phy_data); +??? /* Disable the time synchronization clock */ +??? mac_data = er32(FEXTNVM7); +??? mac_data |= BIT(31); +??? mac_data &= ~BIT(0); +??? ew32(FEXTNVM7, mac_data); -??? mac_data = er32(EXTCNF_CTRL); -??? mac_data |= E1000_EXTCNF_CTRL_GATE_PHY_CFG; -??? ew32(EXTCNF_CTRL, mac_data); +??? /* Dynamic Power Gating Enable */ +??? mac_data = er32(CTRL_EXT); +??? mac_data |= BIT(3); +??? ew32(CTRL_EXT, mac_data);????? /* Check MAC Tx/Rx packet buffer pointers. ?????? * Reset MAC Tx/Rx packet buffer pointers to suppress any
drivers/net/ethernet/intel/e1000e/netdev.c +75
-85@@ -6416,59 +6478,6 @@ static void e1000e_s0ix_entry_flow(struct e1000_adapter *adapter) ????? mac_data = er32(RDFPC); ????? if (mac_data) ????????? ew32(RDFPC, 0); - -??? /* Enable the Dynamic Power Gating in the MAC */ -??? mac_data = er32(FEXTNVM7); -??? mac_data |= BIT(22); -??? ew32(FEXTNVM7, mac_data); - -??? /* Disable the time synchronization clock */ -??? mac_data = er32(FEXTNVM7); -??? mac_data |= BIT(31); -??? mac_data &= ~BIT(0); -??? ew32(FEXTNVM7, mac_data); - -??? /* Dynamic Power Gating Enable */ -??? mac_data = er32(CTRL_EXT); -??? mac_data |= BIT(3); -??? ew32(CTRL_EXT, mac_data); - -??? /* Disable disconnected cable conditioning for Power Gating */ -??? mac_data = er32(DPGFR); -??? mac_data |= BIT(2); -??? ew32(DPGFR, mac_data); - -??? /* Don't wake from dynamic Power Gating with clock request */ -??? mac_data = er32(FEXTNVM12); -??? mac_data |= BIT(12); -??? ew32(FEXTNVM12, mac_data); - -??? /* Ungate PGCB clock */ -??? mac_data = er32(FEXTNVM9); -??? mac_data &= ~BIT(28); -??? ew32(FEXTNVM9, mac_data); - -??? /* Enable K1 off to enable mPHY Power Gating */ -??? mac_data = er32(FEXTNVM6); -??? mac_data |= BIT(31); -??? ew32(FEXTNVM6, mac_data); - -??? /* Enable mPHY power gating for any link and speed */ -??? mac_data = er32(FEXTNVM8); -??? mac_data |= BIT(9); -??? ew32(FEXTNVM8, mac_data); - -??? /* Enable the Dynamic Clock Gating in the DMA and MAC */ -??? mac_data = er32(CTRL_EXT); -??? mac_data |= E1000_CTRL_EXT_DMA_DYN_CLK_EN; -??? ew32(CTRL_EXT, mac_data); - -??? /* No MAC DPG gating SLP_S0 in modern standby -???? * Switch the logic of the lanphypc to use PMC counter -???? */ -??? mac_data = er32(FEXTNVM5); -??? mac_data |= BIT(7); -??? ew32(FEXTNVM5, mac_data); ? } ? static void e1000e_s0ix_exit_flow(struct e1000_adapter *adapter)@@ -6477,87 +6486,98 @@ static void e1000e_s0ix_exit_flow(struct e1000_adapter *adapter) ????? u32 mac_data; ????? u16 phy_data; -??? /* Disable the Dynamic Power Gating in the MAC */ -??? mac_data = er32(FEXTNVM7); -??? mac_data &= 0xFFBFFFFF; -??? ew32(FEXTNVM7, mac_data); +??? if (er32(FWSM) & E1000_ICH_FWSM_FW_VALID) { +??????? /* Request ME un configure the device from s0ix */ +??????? mac_data = er32(H2ME); +??????? mac_data &= ~E1000_H2ME_START_DPG; +??????? mac_data |= E1000_H2ME_EXIT_DPG; +??????? ew32(H2ME, mac_data); +??? } else { +??????? /* Request driver un configure the device from s0ix */ + +??????? /* Disable the Dynamic Power Gating in the MAC */ +??????? mac_data = er32(FEXTNVM7); +??????? mac_data &= 0xFFBFFFFF; +??????? ew32(FEXTNVM7, mac_data); + +??????? /* Disable mPHY power gating for any link and speed */ +??????? mac_data = er32(FEXTNVM8); +??????? mac_data &= ~BIT(9); +??????? ew32(FEXTNVM8, mac_data); + +??????? /* Disable K1 off */ +??????? mac_data = er32(FEXTNVM6); +??????? mac_data &= ~BIT(31); +??????? ew32(FEXTNVM6, mac_data); + +??????? /* Disable Ungate PGCB clock */ +??????? mac_data = er32(FEXTNVM9); +??????? mac_data |= BIT(28); +??????? ew32(FEXTNVM9, mac_data); + +??????? /* Cancel not waking from dynamic +???????? * Power Gating with clock request +???????? */ +??????? mac_data = er32(FEXTNVM12); +??????? mac_data &= ~BIT(12); +??????? ew32(FEXTNVM12, mac_data); -??? /* Enable the time synchronization clock */ -??? mac_data = er32(FEXTNVM7); -??? mac_data |= BIT(0); -??? ew32(FEXTNVM7, mac_data); +??????? /* Cancel disable disconnected cable conditioning +???????? * for Power Gating +???????? */ +??????? mac_data = er32(DPGFR); +??????? mac_data &= ~BIT(2); +??????? ew32(DPGFR, mac_data); -??? /* Disable mPHY power gating for any link and speed */ -??? mac_data = er32(FEXTNVM8); -??? mac_data &= ~BIT(9); -??? ew32(FEXTNVM8, mac_data); +??????? /* Disable the Dynamic Clock Gating in the DMA and MAC */ +??????? mac_data = er32(CTRL_EXT); +??????? mac_data &= 0xFFF7FFFF; +??????? ew32(CTRL_EXT, mac_data); -??? /* Disable K1 off */ -??? mac_data = er32(FEXTNVM6); -??? mac_data &= ~BIT(31); -??? ew32(FEXTNVM6, mac_data); +??????? /* Revert the lanphypc logic to use the internal Gbe counter +???????? * and not the PMC counter +???????? */ +??????? mac_data = er32(FEXTNVM5); +??????? mac_data &= 0xFFFFFF7F; +??????? ew32(FEXTNVM5, mac_data); -??? /* Disable Ungate PGCB clock */ -??? mac_data = er32(FEXTNVM9); -??? mac_data |= BIT(28); -??? ew32(FEXTNVM9, mac_data); +??????? /* Enable the periodic inband message, +???????? * Request PCIe clock in K1 page770_17[10:9] =01b +???????? */ +??????? e1e_rphy(hw, HV_PM_CTRL, &phy_data); +??????? phy_data &= 0xFBFF; +??????? phy_data |= HV_PM_CTRL_K1_CLK_REQ; +??????? e1e_wphy(hw, HV_PM_CTRL, phy_data); -??? /* Cancel not waking from dynamic -???? * Power Gating with clock request -???? */ -??? mac_data = er32(FEXTNVM12); -??? mac_data &= ~BIT(12); -??? ew32(FEXTNVM12, mac_data); +??????? /* Return back configuration +???????? * 772_29[5] = 0 CS_Mode_Stay_In_K1 +???????? */ +??????? e1e_rphy(hw, I217_CGFREG, &phy_data); +??????? phy_data &= 0xFFDF; +??????? e1e_wphy(hw, I217_CGFREG, phy_data); -??? /* Cancel disable disconnected cable conditioning -???? * for Power Gating -???? */ -??? mac_data = er32(DPGFR); -??? mac_data &= ~BIT(2); -??? ew32(DPGFR, mac_data); +??????? /* Change the MAC/PHY interface to Kumeran +???????? * Unforce the SMBus in PHY page769_23[0] = 0 +???????? * Unforce the SMBus in MAC CTRL_EXT[11] = 0 +???????? */ +??????? e1e_rphy(hw, CV_SMB_CTRL, &phy_data); +??????? phy_data &= ~CV_SMB_CTRL_FORCE_SMBUS; +??????? e1e_wphy(hw, CV_SMB_CTRL, phy_data); +??????? mac_data = er32(CTRL_EXT); +??????? mac_data &= ~E1000_CTRL_EXT_FORCE_SMBUS; +??????? ew32(CTRL_EXT, mac_data); +??? }????? /* Disable Dynamic Power Gating */
?????mac_data=er32(CTRL_EXT);
?????mac_data&=0xFFFFFFF7;
?????ew32(CTRL_EXT, mac_data);
-??? /* Disable the Dynamic Clock Gating in the DMA and MAC */ -???mac_data=er32(CTRL_EXT);
-???mac_data&=0xFFF7FFFF;
-???ew32(CTRL_EXT, mac_data);drivers/net/ethernet/intel/e1000e/netdev.c +0
-33- -??? /* Revert the lanphypc logic to use the internal Gbe counter -???? * and not the PMC counter -???? */ -??? mac_data = er32(FEXTNVM5); -??? mac_data &= 0xFFFFFF7F; -??? ew32(FEXTNVM5, mac_data); - -??? /* Enable the periodic inband message, -???? * Request PCIe clock in K1 page770_17[10:9] =01b -???? */ -??? e1e_rphy(hw, HV_PM_CTRL, &phy_data); -??? phy_data &= 0xFBFF; -??? phy_data |= HV_PM_CTRL_K1_CLK_REQ; -??? e1e_wphy(hw, HV_PM_CTRL, phy_data); - -??? /* Return back configuration -???? * 772_29[5] = 0 CS_Mode_Stay_In_K1 -???? */ -??? e1e_rphy(hw, I217_CGFREG, &phy_data); -??? phy_data &= 0xFFDF; -??? e1e_wphy(hw, I217_CGFREG, phy_data); - -??? /* Change the MAC/PHY interface to Kumeran -???? * Unforce the SMBus in PHY page769_23[0] = 0 -???? * Unforce the SMBus in MAC CTRL_EXT[11] = 0 -???? */ -??? e1e_rphy(hw, CV_SMB_CTRL, &phy_data); -??? phy_data &= ~CV_SMB_CTRL_FORCE_SMBUS; -??? e1e_wphy(hw, CV_SMB_CTRL, phy_data); -??? mac_data = er32(CTRL_EXT); -??? mac_data &= ~E1000_CTRL_EXT_FORCE_SMBUS; -??? ew32(CTRL_EXT, mac_data);
Quoted 8 lines
Quoted 8 lines
+??? /* Enable the time synchronization clock */
+???mac_data= er32(FEXTNVM7);
+???mac_data&= ~BIT(31);
+???mac_data|= BIT(0);
+???ew32(FEXTNVM7, mac_data);
? }
? static inte1000e_pm_freeze(struct device *dev)
Paul,
see my answer inline.Thanks, Sasha
Fuxbrumer
PATCH 1/3 e1000e: Add handshake with the CSME to support s0ix
In reply to Sasha NeftinQuoted 5 lines · Sasha Neftin
On the corporate system, the driver will ask from the CSME (manageability engine) to perform device settings are required to allow s0ix residency.
This patch provides initial support.
Quoted 7 lines
Reviewed-by Dima Ruinskiy <[email protected]>Signed-off-by Sasha Neftin <[email protected]>--- drivers/net/ethernet/intel/e1000e/ich8lan.h | 2 + drivers/net/ethernet/intel/e1000e/netdev.c | 328 +++++++++++--------- 2 files changed, 176 insertions(+), 154 deletions(-)