drm/i915/psr: Only lookup for enabled CRTCs when forcing a fastset
Subsystems (2)
PATCH 1/4 drm/i915/psr: Only lookup for enabled CRTCs when forcing a fastset
Forcing a specific CRTC to the eDP connector was causing the intel_psr_fastset_force() to mark mode_chaged in the wrong and disabled CRTC causing no update in the PSR state.
Looks like our internal state track do not clear output_types and has_psr in the disabled CRTCs, not sure if this is the expected behavior or not but in the mean time this fix the issue.
--- drivers/gpu/drm/i915/intel_psr.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/gpu/drm/i915/intel_psr.c +2 -1
@@ -986,7 +986,8 @@ static int intel_psr_fastset_force(struct drm_i915_private *dev_priv) intel_crtc_state =to_intel_crtc_state (crtc_state); -if (intel_crtc_has_type (intel_crtc_state,INTEL_OUTPUT_EDP ) && +if (crtc_state->enable && +intel_crtc_has_type (intel_crtc_state,INTEL_OUTPUT_EDP ) && intel_crtc_state->has_psr) {/* Mark mode as changed to trigger a pipe->update() */ crtc_state->mode_changed = true;
Signature · 6 lines
2.20.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 2/4 drm/i915: Disable PSR2 while getting pipe CRC
As stated in CRC_CTL spec, after PSR entry state CRC will not be calculated anymore what is not a problem as IGT tests do some screen change and then request the pipe CRC right after the change so PSR will go to idle state and only will entry again after at least 6 idles frames.
But for PSR2 it is more problematic as any change to the screen could trigger a selective/partial update causing the CRC value not to be calculated over the full frame.
So here it disables PSR2 and keep it disabled while user is requesting pipe CRC.
BSpec: 7536
--- drivers/gpu/drm/i915/i915_drv.h | 1 + drivers/gpu/drm/i915/intel_drv.h | 1 + drivers/gpu/drm/i915/intel_pipe_crc.c | 10 ++++++++++ drivers/gpu/drm/i915/intel_psr.c | 23 +++++++++++++++++++++++ 4 files changed, 35 insertions(+)
drivers/gpu/drm/i915/i915_drv.h +1 -0
@@ -520,6 +520,7 @@ struct i915_psr {bool sink_not_reliable;bool irq_aux_error;u16 su_x_granularity; +bool pipe_crc_enabled; };enum intel_pch {
drivers/gpu/drm/i915/intel_drv.h +1 -0
@@ -2103,6 +2103,7 @@ void intel_psr_short_pulse(struct intel_dp *intel_dp);int intel_psr_wait_for_idle (const struct intel_crtc_state *new_crtc_state,u32 *out_value);bool intel_psr_enabled (struct intel_dp *intel_dp); +void intel_psr_crc_prepare_or_finish (struct drm_i915_private *dev_priv,enum pipe pipe,bool prepare);/* intel_quirks.c */ void intel_init_quirks (struct drm_i915_private *dev_priv);
drivers/gpu/drm/i915/intel_pipe_crc.c +10 -0
@@ -583,6 +583,14 @@ int intel_crtc_verify_crc_source(struct drm_crtc *crtc, const char *source_name,return -EINVAL ; } +static inline void intel_crtc_crc_prepare_or_finish (struct drm_crtc *crtc,bool prepare) +{ +struct drm_i915_private *dev_priv =to_i915 (crtc->dev); +struct intel_crtc *intel_crtc =to_intel_crtc (crtc); + +intel_psr_crc_prepare_or_finish (dev_priv, intel_crtc->pipe, prepare); +} +int intel_crtc_set_crc_source (struct drm_crtc *crtc,const char *source_name) {struct drm_i915_private *dev_priv =to_i915 (crtc->dev);
@@ -609,6 +617,8 @@ int intel_crtc_set_crc_source(struct drm_crtc *crtc, const char *source_name)if (ret !=0 ) goto out; +intel_crtc_crc_prepare_or_finish (crtc, source !=INTEL_PIPE_CRC_SOURCE_NONE ); + pipe_crc->source = source;I915_WRITE (PIPE_CRC_CTL (crtc->index), val);POSTING_READ (PIPE_CRC_CTL (crtc->index));
drivers/gpu/drm/i915/intel_psr.c +23 -0
@@ -577,6 +577,9 @@ static bool intel_psr2_config_valid(struct intel_dp *intel_dp,return false; } +if (dev_priv->psr.pipe_crc_enabled) +return false; +return true; }
@@ -1291,3 +1294,23 @@ bool intel_psr_enabled(struct intel_dp *intel_dp)return ret; } + +void intel_psr_crc_prepare_or_finish (struct drm_i915_private *dev_priv,enum pipe pipe,bool prepare) +{ +bool fastset = false; + +if (!CAN_PSR (dev_priv)) +return ; + +mutex_lock (&dev_priv->psr.lock); + +if (dev_priv->psr.pipe == pipe) { + dev_priv->psr.pipe_crc_enabled = prepare; + fastset = !prepare || dev_priv->psr.psr2_enabled; + } + +mutex_unlock (&dev_priv->psr.lock); + +if (fastset) +intel_psr_fastset_force (dev_priv); +}
Signature · 6 lines
2.20.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 2/4] drm/i915: Disable PSR2 while getting pipe CRC
Quoted 9 lines · José Roberto de Souza
As stated in
CRC_CTLspec, after PSR entry state CRC will not be calculated anymore what is not a problem as IGT tests do some screen change and then request the pipe CRC right after the change so PSR will go to idle state and only will entry again after at least 6 idles frames.But for PSR2 it is more problematic as any change to the screen could trigger a selective/partial update causing the CRC value not to be calculated over the full frame.
Okay, that reasoning runs counter to my understanding. My understanding is that the whole frame is fetched and processed at the pipe level but the DDI sends selective blocks of pixels. So, if the CRC's are calculated at the pipe level, the CRC should be for the full frame with PSR2 having no effect? Checking bspec, I see there are DDI CRCs as well, which should reflect the partial frame that PSR2 sends.
To get a better understanding, I'd like to know what the source for mismatching CRCs is?
Quoted 111 lines
So here it disables PSR2 and keep it disabled while user is requesting pipe CRC.
BSpec: 7536
Cc Dhinakaran Pandiyan <[email protected]>Cc Ville Syrjälä <[email protected]>Signed-off-by José Roberto de Souza <[email protected]>--- drivers/gpu/drm/i915/i915_drv.h | 1 + drivers/gpu/drm/i915/intel_drv.h | 1 + drivers/gpu/drm/i915/intel_pipe_crc.c | 10 ++++++++++ drivers/gpu/drm/i915/intel_psr.c | 23 +++++++++++++++++++++++ 4 files changed, 35 insertions(+)drivers/gpu/drm/i915/i915_drv.h +1
-0@@ -520,6 +520,7 @@ struct i915_psr {bool sink_not_reliable;bool irq_aux_error;u16 su_x_granularity; +bool pipe_crc_enabled; };enum intel_pch {drivers/gpu/drm/i915/intel_drv.h +1
-0@@ -2103,6 +2103,7 @@ void intel_psr_short_pulse(struct intel_dp *intel_dp);int intel_psr_wait_for_idle (const struct intel_crtc_state *new_crtc_state,u32 *out_value);bool intel_psr_enabled (struct intel_dp *intel_dp); +void intel_psr_crc_prepare_or_finish (struct drm_i915_private *dev_priv,enum pipe pipe,bool prepare);/*
intel_quirks.c*/
voidintel_init_quirks(struct drm_i915_private *dev_priv);drivers/gpu/drm/i915/intel_pipe_crc.c +8
-0@@ -583,6 +583,14 @@ int intel_crtc_verify_crc_source(struct drm_crtc *crtc, const char *source_name, return -EINVAL ; } +static inline void intel_crtc_crc_prepare_or_finish (struct drm_crtc *crtc,bool prepare) +{ +struct drm_i915_private *dev_priv =to_i915 (crtc->dev); +struct intel_crtc *intel_crtc =to_intel_crtc (crtc); + +intel_psr_crc_prepare_or_finish (dev_priv, intel_crtc->pipe, prepare); +} +int intel_crtc_set_crc_source(struct
drm_crtc*crtc, const char*source_name)
{drivers/gpu/drm/i915/intel_pipe_crc.c +2
-0struct drm_i915_private *dev_priv =to_i915 (crtc->dev);@@ -609,6 +617,8 @@ int intel_crtc_set_crc_source(struct drm_crtc *crtc, const char *source_name)if (ret !=0 ) goto out; +intel_crtc_crc_prepare_or_finish (crtc, source !=INTEL_PIPE_CRC_SOURCE_NONE ); + pipe_crc->source = source;drivers/gpu/drm/i915/intel_pipe_crc.c +0
-0I915_WRITE (PIPE_CRC_CTL (crtc->index), val);POSTING_READ (PIPE_CRC_CTL (crtc->index));drivers/gpu/drm/i915/intel_psr.c +5
-0@@ -577,6 +577,9 @@ static bool intel_psr2_config_valid(structintel_dp *intel_dp, return false; } +if (dev_priv->psr.pipe_crc_enabled) +return false; +return true; }@@ -1291,3 +1294,23 @@ bool intel_psr_enabled(struct intel_dp *intel_dp)return ret; } + +void intel_psr_crc_prepare_or_finish(struct drm_i915_private
*dev_priv, enum pipe pipe, bool prepare)drivers/gpu/drm/i915/intel_psr.c +8
-0+{ +bool fastset = false; + +if (!CAN_PSR (dev_priv)) +return ; + +mutex_lock (&dev_priv->psr.lock); +
drivers/gpu/drm/i915/intel_psr.c bool intel_psr_enabled(struct intel_dp *intel_dp) · line 1316
Quoted 10 lines
drivers/gpu/drm/i915/intel_psr.c +10
-0+if (dev_priv->psr.pipe == pipe) { + dev_priv->psr.pipe_crc_enabled = prepare; + fastset = !prepare || dev_priv->psr.psr2_enabled; + } + +mutex_unlock (&dev_priv->psr.lock); + +if (fastset) +intel_psr_fastset_force (dev_priv); +}
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 2/4] drm/i915: Disable PSR2 while getting pipe CRC
Quoted 22 lines · Dhinakaran Pandiyan
Quoted 11 lines · José Roberto de Souza
As stated in
CRC_CTLspec, after PSR entry state CRC will not be calculated anymore what is not a problem as IGT tests do some screen
change and then request the pipe CRC right after the change so PSR will go to idle state and only will entry again after at least 6 idles frames.But for PSR2 it is more problematic as any change to the screen could
trigger a selective/partial update causing the CRC value not to be calculated over the full frame.Okay, that reasoning runs counter to my understanding. My understanding
is that the whole frame is fetched and processed at the pipe level but
the DDI sends selective blocks of pixels. So, if the CRC's are calculated at the pipe level, the CRC should be for the full frame with
PSR2 having no effect? Checking bspec, I see there are DDI CRCs as well, which should reflect the partial frame that PSR2 sends.
Quoted 2 lines
To get a better understanding, I'd like to know what the source for mismatching CRCs is?
Well the naming is misleading for newer gens, before BDW this was a pipe register(8067) but now it is a DDI register(7536) but the register offset was kept the same.
In my testing hardware generate 4 interruptions with wrong CRC values then stops forever probably because vblank interruptions are off.
Quoted 117 lines
Quoted 117 lines
So here it disables PSR2 and keep it disabled while user is requesting pipe CRC.
BSpec: 7536
Cc Dhinakaran Pandiyan <[email protected]>Cc Ville Syrjälä <[email protected]>Signed-off-by José Roberto de Souza <[email protected]>--- drivers/gpu/drm/i915/i915_drv.h | 1 + drivers/gpu/drm/i915/intel_drv.h | 1 + drivers/gpu/drm/i915/intel_pipe_crc.c | 10 ++++++++++ drivers/gpu/drm/i915/intel_psr.c | 23 +++++++++++++++++++++++ 4 files changed, 35 insertions(+)drivers/gpu/drm/i915/i915_drv.h +1
-0@@ -520,6 +520,7 @@ struct i915_psr {bool sink_not_reliable;bool irq_aux_error;u16 su_x_granularity; +bool pipe_crc_enabled; };enum intel_pch {drivers/gpu/drm/i915/intel_drv.h +1
-0@@ -2103,6 +2103,7 @@ void intel_psr_short_pulse(struct intel_dp *intel_dp);int intel_psr_wait_for_idle (const struct intel_crtc_state *new_crtc_state,u32 *out_value);bool intel_psr_enabled (struct intel_dp *intel_dp); +void intel_psr_crc_prepare_or_finish (struct drm_i915_private *dev_priv,enum pipe pipe,bool prepare);/*
intel_quirks.c*/
voidintel_init_quirks(struct drm_i915_private *dev_priv);drivers/gpu/drm/i915/intel_pipe_crc.c +0
-0@@ -583,6 +583,14 @@ int intel_crtc_verify_crc_source(struct
drm_crtc
*crtc, const char*source_name,drivers/gpu/drm/i915/intel_pipe_crc.c +1
-0return -EINVAL ; } +static inline void intel_crtc_crc_prepare_or_finish(struct
drm_crtc
*crtc, bool prepare)drivers/gpu/drm/i915/intel_pipe_crc.c +5
-0+{ +struct drm_i915_private *dev_priv =to_i915 (crtc->dev); +struct intel_crtc *intel_crtc =to_intel_crtc (crtc); + + intel_psr_crc_prepare_or_finish(dev_priv, intel_crtc->pipe,prepare);
drivers/gpu/drm/i915/intel_pipe_crc.c +2
-0+} + int intel_crtc_set_crc_source(struct drm_crtc *crtc, const char
*source_name)
{drivers/gpu/drm/i915/intel_pipe_crc.c +2
-0struct drm_i915_private *dev_priv =to_i915 (crtc->dev);@@ -609,6 +617,8 @@ int intel_crtc_set_crc_source(struct drm_crtc *crtc, const char *source_name)if (ret !=0 ) goto out; +intel_crtc_crc_prepare_or_finish (crtc, source !=INTEL_PIPE_CRC_SOURCE_NONE ); + pipe_crc->source = source;drivers/gpu/drm/i915/intel_pipe_crc.c +0
-0I915_WRITE (PIPE_CRC_CTL (crtc->index), val);POSTING_READ (PIPE_CRC_CTL (crtc->index));drivers/gpu/drm/i915/intel_psr.c +5
-0@@ -577,6 +577,9 @@ static bool intel_psr2_config_valid(structintel_dp *intel_dp, return false; } +if (dev_priv->psr.pipe_crc_enabled) +return false; +return true; }@@ -1291,3 +1294,23 @@ bool intel_psr_enabled(struct intel_dp *intel_dp)return ret; } + +void intel_psr_crc_prepare_or_finish(struct drm_i915_private
*dev_priv, enum pipe pipe, bool prepare)drivers/gpu/drm/i915/intel_psr.c +10
-0+{ +bool fastset = false; + +if (!CAN_PSR (dev_priv)) +return ; + +mutex_lock (&dev_priv->psr.lock); + +if (dev_priv->psr.pipe == pipe) { + dev_priv->psr.pipe_crc_enabled = prepare;
Quoted 8 lines
drivers/gpu/drm/i915/intel_psr.c bool intel_psr_enabled(struct intel_dp *intel_dp) · line 1316
Quoted 8 lines
drivers/gpu/drm/i915/intel_psr.c +8
-0+ fastset = !prepare || dev_priv->psr.psr2_enabled; + } + +mutex_unlock (&dev_priv->psr.lock); + +if (fastset) +intel_psr_fastset_force (dev_priv); +}
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 2/4] drm/i915: Disable PSR2 while getting pipe CRC
Quoted 26 lines · Jose
Quoted 25 lines · Dhinakaran Pandiyan
Quoted 8 lines · José Roberto de Souza
As stated in
CRC_CTLspec, after PSR entry state CRC will not be calculated anymore what is not a problem as IGT tests do some screen
change and then request the pipe CRC right after the change so PSR
will go to idle state and only will entry again after at least 6 idles frames.Quoted 5 lines
But for PSR2 it is more problematic as any change to the screen could
trigger a selective/partial update causing the CRC value not to be
calculated over the full frame.Okay, that reasoning runs counter to my understanding. My understanding
is that the whole frame is fetched and processed at the pipe level but
the DDI sends selective blocks of pixels. So, if the CRC's are calculated at the pipe level, the CRC should be for the full frame with
PSR2 having no effect? Checking bspec, I see there are DDI CRCs as well, which should reflect the partial frame that PSR2 sends.
Quoted 7 lines
Quoted 2 lines
To get a better understanding, I'd like to know what the source for mismatching CRCs is?
Well the naming is misleading for newer gens, before BDW this was a pipe register(8067) but now it is a DDI register(7536) but the register
offset was kept the same.
Do we even read this register DDI_CRC_CTL? Don't see it defined in i915_reg.h or referenced in intel_pipe_crc.c.
Quoted 3 lines
In my testing hardware generate 4 interruptions with wrong CRC values then stops forever probably because vblank interruptions are off.
Yeah, my guess is that power management is affecting the CRC generation rather than pipe CRC's being calculated only on the SU update blocks.
Quoted 118 lines
Quoted 118 lines
Quoted 118 lines
So here it disables PSR2 and keep it disabled while user is requesting pipe CRC.
BSpec: 7536
Cc Dhinakaran Pandiyan <[email protected]>Cc Ville Syrjälä <[email protected]>Signed-off-by José Roberto de Souza <[email protected]>--- drivers/gpu/drm/i915/i915_drv.h | 1 + drivers/gpu/drm/i915/intel_drv.h | 1 + drivers/gpu/drm/i915/intel_pipe_crc.c | 10 ++++++++++ drivers/gpu/drm/i915/intel_psr.c | 23 +++++++++++++++++++++++ 4 files changed, 35 insertions(+)drivers/gpu/drm/i915/i915_drv.h +1
-0@@ -520,6 +520,7 @@ struct i915_psr {bool sink_not_reliable;bool irq_aux_error;u16 su_x_granularity; +bool pipe_crc_enabled; };enum intel_pch {drivers/gpu/drm/i915/intel_drv.h +1
-0@@ -2103,6 +2103,7 @@ void intel_psr_short_pulse(struct intel_dp *intel_dp);int intel_psr_wait_for_idle (const struct intel_crtc_state *new_crtc_state,u32 *out_value);bool intel_psr_enabled (struct intel_dp *intel_dp); +void intel_psr_crc_prepare_or_finish (struct drm_i915_private *dev_priv,enum pipe pipe,bool prepare);/*
intel_quirks.c*/
voidintel_init_quirks(struct drm_i915_private *dev_priv);drivers/gpu/drm/i915/intel_pipe_crc.c +0
-0@@ -583,6 +583,14 @@ int intel_crtc_verify_crc_source(struct
drm_crtc
*crtc, const char*source_name,drivers/gpu/drm/i915/intel_pipe_crc.c +1
-0return -EINVAL ; } +static inline void intel_crtc_crc_prepare_or_finish(struct
drm_crtc
*crtc, bool prepare)drivers/gpu/drm/i915/intel_pipe_crc.c +5
-0+{ +struct drm_i915_private *dev_priv =to_i915 (crtc->dev); +struct intel_crtc *intel_crtc =to_intel_crtc (crtc); + + intel_psr_crc_prepare_or_finish(dev_priv, intel_crtc->pipe,prepare);
drivers/gpu/drm/i915/intel_pipe_crc.c +2
-0+} + int intel_crtc_set_crc_source(struct drm_crtc *crtc, const char
*source_name)
{drivers/gpu/drm/i915/intel_pipe_crc.c +2
-0struct drm_i915_private *dev_priv =to_i915 (crtc->dev);@@ -609,6 +617,8 @@ int intel_crtc_set_crc_source(struct drm_crtc *crtc, const char *source_name)if (ret !=0 ) goto out; +intel_crtc_crc_prepare_or_finish (crtc, source !=INTEL_PIPE_CRC_SOURCE_NONE ); + pipe_crc->source = source;drivers/gpu/drm/i915/intel_pipe_crc.c +0
-0I915_WRITE (PIPE_CRC_CTL (crtc->index), val);POSTING_READ (PIPE_CRC_CTL (crtc->index));drivers/gpu/drm/i915/intel_psr.c +5
-0@@ -577,6 +577,9 @@ static bool intel_psr2_config_valid(structintel_dp *intel_dp, return false; } +if (dev_priv->psr.pipe_crc_enabled) +return false; +return true; }@@ -1291,3 +1294,23 @@ bool intel_psr_enabled(struct intel_dp *intel_dp)return ret; } + +void intel_psr_crc_prepare_or_finish(struct drm_i915_private
*dev_priv, enum pipe pipe, bool prepare)drivers/gpu/drm/i915/intel_psr.c +10
-0+{ +bool fastset = false; + +if (!CAN_PSR (dev_priv)) +return ; + +mutex_lock (&dev_priv->psr.lock); + +if (dev_priv->psr.pipe == pipe) { + dev_priv->psr.pipe_crc_enabled = prepare;
Quoted 8 lines
Quoted 8 lines
drivers/gpu/drm/i915/intel_psr.c bool intel_psr_enabled(struct intel_dp *intel_dp) · line 1316
Quoted 8 lines
drivers/gpu/drm/i915/intel_psr.c +8
-0+ fastset = !prepare || dev_priv->psr.psr2_enabled; + } + +mutex_unlock (&dev_priv->psr.lock); + +if (fastset) +intel_psr_fastset_force (dev_priv); +}
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 2/4] drm/i915: Disable PSR2 while getting pipe CRC
Quoted 36 lines · Dhinakaran
Quoted 35 lines · Jose
Quoted 33 lines · Dhinakaran Pandiyan
Quoted 10 lines · José Roberto de Souza
As stated in
CRC_CTLspec, after PSR entry state CRC will not be
calculated anymore what is not a problem as IGT tests do some screen
change and then request the pipe CRC right after the change so PSR
will go to idle state and only will entry again after at least 6
idles frames.Quoted 5 lines
But for PSR2 it is more problematic as any change to the screen could
trigger a selective/partial update causing the CRC value not to be
calculated over the full frame.Okay, that reasoning runs counter to my understanding. My understanding
is that the whole frame is fetched and processed at the pipe level
but
the DDI sends selective blocks of pixels. So, if the CRC's are calculated at the pipe level, the CRC should be for the full frame
with
PSR2 having no effect? Checking bspec, I see there are DDI CRCs as
well, which should reflect the partial frame that PSR2 sends.To get a better understanding, I'd like to know what the source for
mismatching CRCs is?
Quoted 6 lines
Quoted 4 lines
Well the naming is misleading for newer gens, before BDW this was a pipe register(8067) but now it is a DDI register(7536) but the register
offset was kept the same.Do we even read this register
DDI_CRC_CTL? Don't see it defined ini915_reg.hor referenced inintel_pipe_crc.c.
We do: PIPE_CRC_CTL().
#define _PIPE_CRC_CTL_A 0x60050
Quoted 130 lines
Quoted 3 lines
In my testing hardware generate 4 interruptions with wrong CRC values
then stops forever probably because vblank interruptions are off.Yeah, my guess is that power management is affecting the CRC generation
rather than pipe CRC's being calculated only on the SU update blocks.Quoted 122 lines
Quoted 122 lines
Quoted 122 lines
So here it disables PSR2 and keep it disabled while user is requesting pipe CRC.
BSpec: 7536
Cc Dhinakaran Pandiyan <[email protected]>Cc Ville Syrjälä <[email protected]>Signed-off-by José Roberto de Souza <[email protected]>--- drivers/gpu/drm/i915/i915_drv.h | 1 + drivers/gpu/drm/i915/intel_drv.h | 1 + drivers/gpu/drm/i915/intel_pipe_crc.c | 10 ++++++++++ drivers/gpu/drm/i915/intel_psr.c | 23 +++++++++++++++++++++++ 4 files changed, 35 insertions(+)drivers/gpu/drm/i915/i915_drv.h +1
-0@@ -520,6 +520,7 @@ struct i915_psr {bool sink_not_reliable;bool irq_aux_error;u16 su_x_granularity; +bool pipe_crc_enabled; };enum intel_pch {drivers/gpu/drm/i915/intel_drv.h +0
-0@@ -2103,6 +2103,7 @@ void intel_psr_short_pulse(struct
intel_dp*intel_dp);
int intel_psr_wait_for_idle(const structintel_crtc_state*new_crtc_state,drivers/gpu/drm/i915/intel_drv.h +1
-0u32 *out_value);bool intel_psr_enabled (struct intel_dp *intel_dp); +void intel_psr_crc_prepare_or_finish(struct drm_i915_private
*dev_priv, enum pipe pipe, bool prepare);/*
intel_quirks.c*/
voidintel_init_quirks(struct drm_i915_private *dev_priv);drivers/gpu/drm/i915/intel_pipe_crc.c +0
-0@@ -583,6 +583,14 @@ int intel_crtc_verify_crc_source(struct
drm_crtc
*crtc, const char*source_name,drivers/gpu/drm/i915/intel_pipe_crc.c +1
-0return -EINVAL ; } +static inline void intel_crtc_crc_prepare_or_finish(struct
drm_crtc
*crtc, bool prepare)drivers/gpu/drm/i915/intel_pipe_crc.c +5
-0+{ +struct drm_i915_private *dev_priv =to_i915 (crtc->dev); +struct intel_crtc *intel_crtc =to_intel_crtc (crtc); + + intel_psr_crc_prepare_or_finish(dev_priv, intel_crtc-Quoted 1 line
pipe,
prepare);
drivers/gpu/drm/i915/intel_pipe_crc.c +2
-0+} + int intel_crtc_set_crc_source(struct drm_crtc *crtc, constchar
*source_name)
{drivers/gpu/drm/i915/intel_pipe_crc.c +0
-0struct drm_i915_private *dev_priv =to_i915 (crtc->dev);@@ -609,6 +617,8 @@ int intel_crtc_set_crc_source(struct
drm_crtc
*crtc, const char*source_name)drivers/gpu/drm/i915/intel_pipe_crc.c +1
-0if (ret !=0 ) goto out; + intel_crtc_crc_prepare_or_finish(crtc, source !=
INTEL_PIPE_CRC_SOURCE_NONE);drivers/gpu/drm/i915/intel_pipe_crc.c +1
-0+ pipe_crc->source = source;I915_WRITE (PIPE_CRC_CTL (crtc->index), val);POSTING_READ (PIPE_CRC_CTL (crtc->index));drivers/gpu/drm/i915/intel_psr.c +5
-0@@ -577,6 +577,9 @@ static bool intel_psr2_config_valid(structintel_dp *intel_dp, return false; } +if (dev_priv->psr.pipe_crc_enabled) +return false; +return true; }@@ -1291,3 +1294,23 @@ bool intel_psr_enabled(struct intel_dp *intel_dp)return ret; } + +void intel_psr_crc_prepare_or_finish(struct drm_i915_private
*dev_priv, enum pipe pipe, bool prepare)drivers/gpu/drm/i915/intel_psr.c +11
-0+{ +bool fastset = false; + +if (!CAN_PSR (dev_priv)) +return ; + +mutex_lock (&dev_priv->psr.lock); + +if (dev_priv->psr.pipe == pipe) { + dev_priv->psr.pipe_crc_enabled = prepare; + fastset = !prepare || dev_priv-
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
drivers/gpu/drm/i915/intel_psr.c bool intel_psr_enabled(struct intel_dp *intel_dp) · line 1316
Quoted 8 lines
Quoted 1 line
psr.psr2_enabled;
drivers/gpu/drm/i915/intel_psr.c +7
-0+ } + +mutex_unlock (&dev_priv->psr.lock); + +if (fastset) +intel_psr_fastset_force (dev_priv); +}
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 2/4] drm/i915: Disable PSR2 while getting pipe CRC
Quoted 46 lines · Jose
Quoted 45 lines · Dhinakaran
Quoted 44 lines · Jose
Quoted 34 lines · Dhinakaran Pandiyan
Quoted 12 lines · José Roberto de Souza
As stated in
CRC_CTLspec, after PSR entry state CRC will not be
calculated anymore what is not a problem as IGT tests do some screen
change and then request the pipe CRC right after the change so
PSR
will go to idle state and only will entry again after at least
6
idles frames.Quoted 7 lines
But for PSR2 it is more problematic as any change to the screen
could
trigger a selective/partial update causing the CRC value not to
be
calculated over the full frame.Okay, that reasoning runs counter to my understanding. My understanding
is that the whole frame is fetched and processed at the pipe level
but
the DDI sends selective blocks of pixels. So, if the CRC's are calculated at the pipe level, the CRC should be for the full frame
with
PSR2 having no effect? Checking bspec, I see there are DDI CRCs as
well, which should reflect the partial frame that PSR2 sends.Quoted 3 lines
To get a better understanding, I'd like to know what the source for
mismatching CRCs is?Well the naming is misleading for newer gens, before BDW this was a
pipe register(8067) but now it is a DDI register(7536) but the register
offset was kept the same.
Quoted 5 lines
Quoted 2 lines
Do we even read this register
DDI_CRC_CTL? Don't see it defined ini915_reg.hor referenced inintel_pipe_crc.c.We do:
PIPE_CRC_CTL().
#define_PIPE_CRC_CTL_A0x60050
I was wrong, the first CRC generated is wrong but it is not read by userspace as we skip it using pipe_crc->skipped it is docummented in the code too.
The problem here is that after PSR2 is activated(after 'Frames Before SU Entry') there is no more CRC interruptions so no calls to drm_crtc_add_crc_entry(), what don't happen with PSR1 even setting a 'Idle Frames' to 1.
Other odd thing that I discovered it that we have CRC_CTL register in DDI(Bspec 7536) and other in PIPE(Bspec 7646) with diferent bits and we write in the transcoder offset using the pipe bits. I tried to use the PIPE offset but it do not generate any interruption, anyone know more about that?
Quoted 133 lines
Quoted 133 lines
Quoted 4 lines
In my testing hardware generate 4 interruptions with wrong CRC values
then stops forever probably because vblank interruptions are off.Yeah, my guess is that power management is affecting the CRC generation
rather than pipe CRC's being calculated only on the SU update blocks.Quoted 123 lines
Quoted 123 lines
Quoted 123 lines
So here it disables PSR2 and keep it disabled while user is requesting pipe CRC.
BSpec: 7536
Cc Dhinakaran Pandiyan <[email protected]>Cc Ville Syrjälä <[email protected]>Signed-off-by José Roberto de Souza <[email protected]>--- drivers/gpu/drm/i915/i915_drv.h | 1 + drivers/gpu/drm/i915/intel_drv.h | 1 + drivers/gpu/drm/i915/intel_pipe_crc.c | 10 ++++++++++ drivers/gpu/drm/i915/intel_psr.c | 23 +++++++++++++++++++++++ 4 files changed, 35 insertions(+)drivers/gpu/drm/i915/i915_drv.h +1
-0@@ -520,6 +520,7 @@ struct i915_psr {bool sink_not_reliable;bool irq_aux_error;u16 su_x_granularity; +bool pipe_crc_enabled; };enum intel_pch {drivers/gpu/drm/i915/intel_drv.h +0
-0@@ -2103,6 +2103,7 @@ void intel_psr_short_pulse(struct
intel_dp*intel_dp);
int intel_psr_wait_for_idle(const structintel_crtc_state*new_crtc_state,drivers/gpu/drm/i915/intel_drv.h +1
-0u32 *out_value);bool intel_psr_enabled (struct intel_dp *intel_dp); +void intel_psr_crc_prepare_or_finish(struct drm_i915_private
*dev_priv, enum pipe pipe, bool prepare);/*
intel_quirks.c*/
voidintel_init_quirks(struct drm_i915_private *dev_priv);drivers/gpu/drm/i915/intel_pipe_crc.c +0
-0@@ -583,6 +583,14 @@ int intel_crtc_verify_crc_source(struct
drm_crtc
*crtc, const char*source_name,drivers/gpu/drm/i915/intel_pipe_crc.c +1
-0return -EINVAL ; } +static inline void intel_crtc_crc_prepare_or_finish(struct
drm_crtc
*crtc, bool prepare)drivers/gpu/drm/i915/intel_pipe_crc.c +5
-0+{ +struct drm_i915_private *dev_priv =to_i915 (crtc->dev); +struct intel_crtc *intel_crtc =to_intel_crtc (crtc); + + intel_psr_crc_prepare_or_finish(dev_priv, intel_crtc-Quoted 1 line
pipe,
prepare);
drivers/gpu/drm/i915/intel_pipe_crc.c +2
-0+} + int intel_crtc_set_crc_source(struct drm_crtc *crtc, constchar
*source_name)
{drivers/gpu/drm/i915/intel_pipe_crc.c +0
-0struct drm_i915_private *dev_priv =to_i915 (crtc->dev);@@ -609,6 +617,8 @@ int intel_crtc_set_crc_source(struct
drm_crtc
*crtc, const char*source_name)drivers/gpu/drm/i915/intel_pipe_crc.c +1
-0if (ret !=0 ) goto out; + intel_crtc_crc_prepare_or_finish(crtc, source !=
INTEL_PIPE_CRC_SOURCE_NONE);drivers/gpu/drm/i915/intel_pipe_crc.c +1
-0+ pipe_crc->source = source;I915_WRITE (PIPE_CRC_CTL (crtc->index), val);POSTING_READ (PIPE_CRC_CTL (crtc->index));drivers/gpu/drm/i915/intel_psr.c +0
-0@@ -577,6 +577,9 @@ static boolintel_psr2_config_valid(struct
intel_dp*intel_dp,drivers/gpu/drm/i915/intel_psr.c +5
-0return false; } +if (dev_priv->psr.pipe_crc_enabled) +return false; +return true; }@@ -1291,3 +1294,23 @@ bool intel_psr_enabled(struct intel_dp *intel_dp)return ret; } + +void intel_psr_crc_prepare_or_finish(struct drm_i915_private
*dev_priv, enum pipe pipe, bool prepare)drivers/gpu/drm/i915/intel_psr.c +11
-0+{ +bool fastset = false; + +if (!CAN_PSR (dev_priv)) +return ; + +mutex_lock (&dev_priv->psr.lock); + +if (dev_priv->psr.pipe == pipe) { + dev_priv->psr.pipe_crc_enabled = prepare; + fastset = !prepare || dev_priv-Quoted 1 line
psr.psr2_enabled;
Quoted 12 lines
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
drivers/gpu/drm/i915/intel_psr.c bool intel_psr_enabled(struct intel_dp *intel_dp) · line 1316
Quoted 7 lines
drivers/gpu/drm/i915/intel_psr.c +7
-0+ } + +mutex_unlock (&dev_priv->psr.lock); + +if (fastset) +intel_psr_fastset_force (dev_priv); +}_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 2/4] drm/i915: Disable PSR2 while getting pipe CRC
Quoted 62 lines · José Roberto de Souza
Quoted 54 lines · Jose
Quoted 53 lines · Dhinakaran
Quoted 52 lines · Jose
Quoted 40 lines · Dhinakaran Pandiyan
Quoted 14 lines · José Roberto de Souza
As stated in
CRC_CTLspec, after PSR entry state CRC will not
be
calculated anymore what is not a problem as IGT tests do some
screen
change and then request the pipe CRC right after the change so
PSR
will go to idle state and only will entry again after at least
6
idles frames.Quoted 8 lines
But for PSR2 it is more problematic as any change to the screen
could
trigger a selective/partial update causing the CRC value not
to
be
calculated over the full frame.Okay, that reasoning runs counter to my understanding. My understanding
is that the whole frame is fetched and processed at the pipe level
but
the DDI sends selective blocks of pixels. So, if the CRC's are
calculated at the pipe level, the CRC should be for the full frame
with
PSR2 having no effect? Checking bspec, I see there are DDI CRCs
as
well, which should reflect the partial frame that PSR2 sends.Quoted 4 lines
To get a better understanding, I'd like to know what the source
for
mismatching CRCs is?Well the naming is misleading for newer gens, before BDW this was
a
pipe register(8067) but now it is a DDI register(7536) but the register
offset was kept the same.Quoted 6 lines
Quoted 3 lines
Do we even read this register
DDI_CRC_CTL? Don't see it defined ini915_reg.hor referenced inintel_pipe_crc.c.We do:
PIPE_CRC_CTL().
#define_PIPE_CRC_CTL_A0x60050
Quoted 8 lines
I was wrong, the first CRC generated is wrong but it is not read by userspace as we skip it using
pipe_crc->skippedit is docummented in the code too.The problem here is that after PSR2 is activated(after 'Frames Before SU Entry') there is no more CRC interruptions so no calls to
drm_crtc_add_crc_entry(), what don't happen with PSR1 even setting a 'Idle Frames' to 1.
So I will update the commit description to:
When PSR2 is active aka after the number of frames programmed in PSR2_CTL 'Frames Before SU Entry' hardware stops to generate CRC interruptions causing IGT tests to fail due timeout.
Oddly that don't happen when PSR1 active, so here it switches from PSR2 to PSR1 while user is requesting pipe CRC.
v2: Changed commit description to describe that PSR2 inhibit CRC calculations.
Quoted 158 lines
Other odd thing that I discovered it that we have
CRC_CTLregister in DDI(Bspec 7536) and other in PIPE(Bspec 7646) with diferent bits and we
write in the transcoder offset using the pipe bits. I tried to use the
PIPE offset but it do not generate any interruption, anyone know more about that?Quoted 149 lines
Quoted 136 lines
Quoted 4 lines
In my testing hardware generate 4 interruptions with wrong CRC values
then stops forever probably because vblank interruptions are off.Yeah, my guess is that power management is affecting the CRC generation
rather than pipe CRC's being calculated only on the SU update blocks.Quoted 126 lines
Quoted 126 lines
Quoted 126 lines
So here it disables PSR2 and keep it disabled while user is requesting pipe CRC.
BSpec: 7536
Cc Dhinakaran Pandiyan <[email protected]>Cc Ville Syrjälä <[email protected]>Signed-off-by José Roberto de Souza <[email protected]>--- drivers/gpu/drm/i915/i915_drv.h | 1 + drivers/gpu/drm/i915/intel_drv.h | 1 + drivers/gpu/drm/i915/intel_pipe_crc.c | 10 ++++++++++ drivers/gpu/drm/i915/intel_psr.c | 23 +++++++++++++++++++++++ 4 files changed, 35 insertions(+)drivers/gpu/drm/i915/i915_drv.h +1
-0@@ -520,6 +520,7 @@ struct i915_psr {bool sink_not_reliable;bool irq_aux_error;u16 su_x_granularity; +bool pipe_crc_enabled; };enum intel_pch {drivers/gpu/drm/i915/intel_drv.h +0
-0@@ -2103,6 +2103,7 @@ void intel_psr_short_pulse(struct
intel_dp*intel_dp);
int intel_psr_wait_for_idle(const structintel_crtc_state*new_crtc_state,drivers/gpu/drm/i915/intel_drv.h +1
-0u32 *out_value);bool intel_psr_enabled (struct intel_dp *intel_dp); +void intel_psr_crc_prepare_or_finish(struct
drm_i915_private*dev_priv, enum pipe pipe, bool prepare);/*
intel_quirks.c*/
voidintel_init_quirks(struct drm_i915_private *dev_priv);drivers/gpu/drm/i915/intel_pipe_crc.c +0
-0@@ -583,6 +583,14 @@ intintel_crtc_verify_crc_source(struct
drm_crtc
*crtc, const char*source_name,drivers/gpu/drm/i915/intel_pipe_crc.c +1
-0return -EINVAL ; } +static inline void intel_crtc_crc_prepare_or_finish(struct
drm_crtc
*crtc, bool prepare)drivers/gpu/drm/i915/intel_pipe_crc.c +5
-0+{ +struct drm_i915_private *dev_priv =to_i915 (crtc->dev); +struct intel_crtc *intel_crtc =to_intel_crtc (crtc); + + intel_psr_crc_prepare_or_finish(dev_priv, intel_crtc-Quoted 1 line
pipe,
prepare);
drivers/gpu/drm/i915/intel_pipe_crc.c +2
-0+} + int intel_crtc_set_crc_source(struct drm_crtc *crtc, constchar
*source_name)
{drivers/gpu/drm/i915/intel_pipe_crc.c +0
-0struct drm_i915_private *dev_priv =to_i915 (crtc->dev);@@ -609,6 +617,8 @@ int intel_crtc_set_crc_source(struct
drm_crtc
*crtc, const char*source_name)drivers/gpu/drm/i915/intel_pipe_crc.c +1
-0if (ret !=0 ) goto out; + intel_crtc_crc_prepare_or_finish(crtc, source !=
INTEL_PIPE_CRC_SOURCE_NONE);drivers/gpu/drm/i915/intel_pipe_crc.c +1
-0+ pipe_crc->source = source;I915_WRITE (PIPE_CRC_CTL (crtc->index), val);POSTING_READ (PIPE_CRC_CTL (crtc->index));drivers/gpu/drm/i915/intel_psr.c +0
-0@@ -577,6 +577,9 @@ static boolintel_psr2_config_valid(struct
intel_dp*intel_dp,drivers/gpu/drm/i915/intel_psr.c +3
-0return false; } +if (dev_priv->psr.pipe_crc_enabled) +return false; +return true; }@@ -1291,3 +1294,23 @@ bool intel_psr_enabled(struct
intel_dp*intel_dp)drivers/gpu/drm/i915/intel_psr.c +2
-0return ret; } + +void intel_psr_crc_prepare_or_finish(struct
drm_i915_private*dev_priv, enum pipe pipe, bool prepare)drivers/gpu/drm/i915/intel_psr.c +11
-0+{ +bool fastset = false; + +if (!CAN_PSR (dev_priv)) +return ; + +mutex_lock (&dev_priv->psr.lock); + +if (dev_priv->psr.pipe == pipe) { + dev_priv->psr.pipe_crc_enabled = prepare; + fastset = !prepare || dev_priv-Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
drivers/gpu/drm/i915/intel_psr.c bool intel_psr_enabled(struct intel_dp *intel_dp) · line 1316
Quoted 8 lines
Quoted 1 line
psr.psr2_enabled;
drivers/gpu/drm/i915/intel_psr.c +7
-0+ } + +mutex_unlock (&dev_priv->psr.lock); + +if (fastset) +intel_psr_fastset_force (dev_priv); +}_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 2/4] drm/i915: Disable PSR2 while getting pipe CRC
In reply to José Roberto de SouzaQuoted 95 lines · José Roberto de Souza
As stated in
CRC_CTLspec, after PSR entry state CRC will not be calculated anymore what is not a problem as IGT tests do some screen change and then request the pipe CRC right after the change so PSR will go to idle state and only will entry again after at least 6 idles frames.But for PSR2 it is more problematic as any change to the screen could trigger a selective/partial update causing the CRC value not to be calculated over the full frame.
So here it disables PSR2 and keep it disabled while user is requesting pipe CRC.
BSpec: 7536
Cc Dhinakaran Pandiyan <[email protected]>Cc Ville Syrjälä <[email protected]>Signed-off-by José Roberto de Souza <[email protected]>--- drivers/gpu/drm/i915/i915_drv.h | 1 + drivers/gpu/drm/i915/intel_drv.h | 1 + drivers/gpu/drm/i915/intel_pipe_crc.c | 10 ++++++++++ drivers/gpu/drm/i915/intel_psr.c | 23 +++++++++++++++++++++++ 4 files changed, 35 insertions(+)drivers/gpu/drm/i915/i915_drv.h +1
-0@@ -520,6 +520,7 @@ struct i915_psr {bool sink_not_reliable;bool irq_aux_error;u16 su_x_granularity; +bool pipe_crc_enabled; };enum intel_pch {drivers/gpu/drm/i915/intel_drv.h +1
-0@@ -2103,6 +2103,7 @@ void intel_psr_short_pulse(struct intel_dp *intel_dp);int intel_psr_wait_for_idle (const struct intel_crtc_state *new_crtc_state,u32 *out_value);bool intel_psr_enabled (struct intel_dp *intel_dp); +void intel_psr_crc_prepare_or_finish (struct drm_i915_private *dev_priv,enum pipe pipe,bool prepare);/*
intel_quirks.c*/
voidintel_init_quirks(struct drm_i915_private *dev_priv);drivers/gpu/drm/i915/intel_pipe_crc.c +8
-0@@ -583,6 +583,14 @@ int intel_crtc_verify_crc_source(struct drm_crtc *crtc, const char *source_name, return -EINVAL ; } +static inline void intel_crtc_crc_prepare_or_finish (struct drm_crtc *crtc,bool prepare) +{ +struct drm_i915_private *dev_priv =to_i915 (crtc->dev); +struct intel_crtc *intel_crtc =to_intel_crtc (crtc); + +intel_psr_crc_prepare_or_finish (dev_priv, intel_crtc->pipe, prepare); +} +int intel_crtc_set_crc_source(struct
drm_crtc*crtc, const char*source_name)
{drivers/gpu/drm/i915/intel_pipe_crc.c +2
-0struct drm_i915_private *dev_priv =to_i915 (crtc->dev);@@ -609,6 +617,8 @@ int intel_crtc_set_crc_source(struct drm_crtc *crtc, const char *source_name)if (ret !=0 ) goto out; +intel_crtc_crc_prepare_or_finish (crtc, source !=INTEL_PIPE_CRC_SOURCE_NONE ); + pipe_crc->source = source;drivers/gpu/drm/i915/intel_pipe_crc.c +0
-0I915_WRITE (PIPE_CRC_CTL (crtc->index), val);POSTING_READ (PIPE_CRC_CTL (crtc->index));drivers/gpu/drm/i915/intel_psr.c +0
-0
drivers/gpu/drm/i915/intel_psr.c static bool intel_psr2_config_valid(struct · line 583
Quoted 7 lines
drivers/gpu/drm/i915/intel_psr.c +3
-0@@ -577,6 +577,9 @@ static bool intel_psr2_config_valid(structintel_dp *intel_dp, return false; } +if (dev_priv->psr.pipe_crc_enabled) +return false; +
Disabling PSR instead of switching to PSR1 is safer considering the past bug reports with PSR1.
Quoted 11 lines
drivers/gpu/drm/i915/intel_psr.c +2
-0return true; }@@ -1291,3 +1294,23 @@ bool intel_psr_enabled(struct intel_dp *intel_dp)return ret; } + +void intel_psr_crc_prepare_or_finish(struct drm_i915_private
*dev_priv, enum pipe pipe, bool prepare)
drivers/gpu/drm/i915/intel_psr.c bool intel_psr_enabled(struct intel_dp *intel_dp) · line 1308
Quoted 10 lines
drivers/gpu/drm/i915/intel_psr.c +10
-0+{ +bool fastset = false; + +if (!CAN_PSR (dev_priv)) +return ; + +mutex_lock (&dev_priv->psr.lock); + +if (dev_priv->psr.pipe == pipe) { + dev_priv->psr.pipe_crc_enabled = prepare;
.crc_enabled seems like it belongs in crtc_state rather than in the global atomic state.
Looks like we could rename and re-purpose crtc_state.ips_force_disable for this. I don't see that flag being used for anything other working around CRC issues.
drivers/gpu/drm/i915/intel_psr.c bool intel_psr_enabled(struct intel_dp *intel_dp) · line 1316
Quoted 8 lines
drivers/gpu/drm/i915/intel_psr.c +8
-0+ fastset = !prepare || dev_priv->psr.psr2_enabled; + } + +mutex_unlock (&dev_priv->psr.lock); + +if (fastset) +intel_psr_fastset_force (dev_priv); +}
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 2/4] drm/i915: Disable PSR2 while getting pipe CRC
Quoted 104 lines · Dhinakaran Pandiyan
Quoted 103 lines · José Roberto de Souza
As stated in
CRC_CTLspec, after PSR entry state CRC will not be calculated anymore what is not a problem as IGT tests do some screen
change and then request the pipe CRC right after the change so PSR will go to idle state and only will entry again after at least 6 idles frames.But for PSR2 it is more problematic as any change to the screen could
trigger a selective/partial update causing the CRC value not to be calculated over the full frame.So here it disables PSR2 and keep it disabled while user is requesting pipe CRC.
BSpec: 7536
Cc Dhinakaran Pandiyan <[email protected]>Cc Ville Syrjälä <[email protected]>Signed-off-by José Roberto de Souza <[email protected]>--- drivers/gpu/drm/i915/i915_drv.h | 1 + drivers/gpu/drm/i915/intel_drv.h | 1 + drivers/gpu/drm/i915/intel_pipe_crc.c | 10 ++++++++++ drivers/gpu/drm/i915/intel_psr.c | 23 +++++++++++++++++++++++ 4 files changed, 35 insertions(+)drivers/gpu/drm/i915/i915_drv.h +1
-0@@ -520,6 +520,7 @@ struct i915_psr {bool sink_not_reliable;bool irq_aux_error;u16 su_x_granularity; +bool pipe_crc_enabled; };enum intel_pch {drivers/gpu/drm/i915/intel_drv.h +1
-0@@ -2103,6 +2103,7 @@ void intel_psr_short_pulse(struct intel_dp *intel_dp);int intel_psr_wait_for_idle (const struct intel_crtc_state *new_crtc_state,u32 *out_value);bool intel_psr_enabled (struct intel_dp *intel_dp); +void intel_psr_crc_prepare_or_finish (struct drm_i915_private *dev_priv,enum pipe pipe,bool prepare);/*
intel_quirks.c*/
voidintel_init_quirks(struct drm_i915_private *dev_priv);drivers/gpu/drm/i915/intel_pipe_crc.c +0
-0@@ -583,6 +583,14 @@ int intel_crtc_verify_crc_source(struct
drm_crtc
*crtc, const char*source_name,drivers/gpu/drm/i915/intel_pipe_crc.c +1
-0return -EINVAL ; } +static inline void intel_crtc_crc_prepare_or_finish(struct
drm_crtc
*crtc, bool prepare)drivers/gpu/drm/i915/intel_pipe_crc.c +5
-0+{ +struct drm_i915_private *dev_priv =to_i915 (crtc->dev); +struct intel_crtc *intel_crtc =to_intel_crtc (crtc); + + intel_psr_crc_prepare_or_finish(dev_priv, intel_crtc->pipe,prepare);
drivers/gpu/drm/i915/intel_pipe_crc.c +2
-0+} + int intel_crtc_set_crc_source(struct drm_crtc *crtc, const char
*source_name)
{drivers/gpu/drm/i915/intel_pipe_crc.c +2
-0struct drm_i915_private *dev_priv =to_i915 (crtc->dev);@@ -609,6 +617,8 @@ int intel_crtc_set_crc_source(struct drm_crtc *crtc, const char *source_name)if (ret !=0 ) goto out; +intel_crtc_crc_prepare_or_finish (crtc, source !=INTEL_PIPE_CRC_SOURCE_NONE ); + pipe_crc->source = source;drivers/gpu/drm/i915/intel_pipe_crc.c +0
-0I915_WRITE (PIPE_CRC_CTL (crtc->index), val);POSTING_READ (PIPE_CRC_CTL (crtc->index));drivers/gpu/drm/i915/intel_psr.c +0
-0@@ -577,6 +577,9 @@ static bool intel_psr2_config_valid(structintel_dp *intel_dp, return false; }
Quoted 6 lines
drivers/gpu/drm/i915/intel_psr.c static bool intel_psr2_config_valid(struct intel_dp *intel_dp, · line 582
Quoted 3 lines
drivers/gpu/drm/i915/intel_psr.c +3
-0+if (dev_priv->psr.pipe_crc_enabled) +return false; +Disabling PSR instead of switching to PSR1 is safer considering the past bug reports with PSR1.
I thought about that but it would break every PSR subtest in kms_frontbuffer_tracking, I guess is better start by disabling PSR2 and then discuss about PSR1 if decided to disable, we need to remove PSR1 from kms_frontbuffer_tracking first.
Quoted 26 lines
Quoted 12 lines
drivers/gpu/drm/i915/intel_psr.c +2
-0return true; }@@ -1291,3 +1294,23 @@ bool intel_psr_enabled(struct intel_dp *intel_dp)return ret; } + +void intel_psr_crc_prepare_or_finish(struct drm_i915_private
*dev_priv, enum pipe pipe, bool prepare)drivers/gpu/drm/i915/intel_psr.c bool intel_psr_enabled(struct intel_dp *intel_dp) · line 1308
Quoted 10 lines
drivers/gpu/drm/i915/intel_psr.c +10
-0+{ +bool fastset = false; + +if (!CAN_PSR (dev_priv)) +return ; + +mutex_lock (&dev_priv->psr.lock); + +if (dev_priv->psr.pipe == pipe) { + dev_priv->psr.pipe_crc_enabled = prepare;.crc_enabled seems like it belongs in
crtc_staterather than in the global atomic state.
Quoted 5 lines
Looks like we could rename and re-purpose crtc_state.ips_force_disable
for this. I don't see that flag being used for anything other working around CRC issues.
My understanging is that we should not update crtc_state or any other state outside of atomic_check() call chain, if that is not true I will rename and reuse ips_force_disable.
Quoted 9 lines
drivers/gpu/drm/i915/intel_psr.c bool intel_psr_enabled(struct intel_dp *intel_dp) · line 1316
Quoted 9 lines
drivers/gpu/drm/i915/intel_psr.c +8
-0+ fastset = !prepare || dev_priv->psr.psr2_enabled; + } + +mutex_unlock (&dev_priv->psr.lock); + +if (fastset) +intel_psr_fastset_force (dev_priv); +}
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 2/4] drm/i915: Disable PSR2 while getting pipe CRC
Quoted 115 lines · Jose
Quoted 107 lines · Dhinakaran Pandiyan
Quoted 106 lines · José Roberto de Souza
As stated in
CRC_CTLspec, after PSR entry state CRC will not be calculated anymore what is not a problem as IGT tests do some screen
change and then request the pipe CRC right after the change so PSR
will go to idle state and only will entry again after at least 6 idles frames.But for PSR2 it is more problematic as any change to the screen could
trigger a selective/partial update causing the CRC value not to be
calculated over the full frame.So here it disables PSR2 and keep it disabled while user is requesting pipe CRC.
BSpec: 7536
Cc Dhinakaran Pandiyan <[email protected]>Cc Ville Syrjälä <[email protected]>Signed-off-by José Roberto de Souza <[email protected]>--- drivers/gpu/drm/i915/i915_drv.h | 1 + drivers/gpu/drm/i915/intel_drv.h | 1 + drivers/gpu/drm/i915/intel_pipe_crc.c | 10 ++++++++++ drivers/gpu/drm/i915/intel_psr.c | 23 +++++++++++++++++++++++ 4 files changed, 35 insertions(+)drivers/gpu/drm/i915/i915_drv.h +1
-0@@ -520,6 +520,7 @@ struct i915_psr {bool sink_not_reliable;bool irq_aux_error;u16 su_x_granularity; +bool pipe_crc_enabled; };enum intel_pch {drivers/gpu/drm/i915/intel_drv.h +1
-0@@ -2103,6 +2103,7 @@ void intel_psr_short_pulse(struct intel_dp *intel_dp);int intel_psr_wait_for_idle (const struct intel_crtc_state *new_crtc_state,u32 *out_value);bool intel_psr_enabled (struct intel_dp *intel_dp); +void intel_psr_crc_prepare_or_finish (struct drm_i915_private *dev_priv,enum pipe pipe,bool prepare);/*
intel_quirks.c*/
voidintel_init_quirks(struct drm_i915_private *dev_priv);drivers/gpu/drm/i915/intel_pipe_crc.c +0
-0@@ -583,6 +583,14 @@ int intel_crtc_verify_crc_source(struct
drm_crtc
*crtc, const char*source_name,drivers/gpu/drm/i915/intel_pipe_crc.c +1
-0return -EINVAL ; } +static inline void intel_crtc_crc_prepare_or_finish(struct
drm_crtc
*crtc, bool prepare)drivers/gpu/drm/i915/intel_pipe_crc.c +5
-0+{ +struct drm_i915_private *dev_priv =to_i915 (crtc->dev); +struct intel_crtc *intel_crtc =to_intel_crtc (crtc); + + intel_psr_crc_prepare_or_finish(dev_priv, intel_crtc->pipe,prepare);
drivers/gpu/drm/i915/intel_pipe_crc.c +2
-0+} + int intel_crtc_set_crc_source(struct drm_crtc *crtc, const char
*source_name)
{drivers/gpu/drm/i915/intel_pipe_crc.c +2
-0struct drm_i915_private *dev_priv =to_i915 (crtc->dev);@@ -609,6 +617,8 @@ int intel_crtc_set_crc_source(struct drm_crtc *crtc, const char *source_name)if (ret !=0 ) goto out; +intel_crtc_crc_prepare_or_finish (crtc, source !=INTEL_PIPE_CRC_SOURCE_NONE ); + pipe_crc->source = source;drivers/gpu/drm/i915/intel_pipe_crc.c +0
-0I915_WRITE (PIPE_CRC_CTL (crtc->index), val);POSTING_READ (PIPE_CRC_CTL (crtc->index));drivers/gpu/drm/i915/intel_psr.c +0
-0@@ -577,6 +577,9 @@ static bool intel_psr2_config_valid(structintel_dp *intel_dp, return false; }Quoted 6 lines
drivers/gpu/drm/i915/intel_psr.c static bool intel_psr2_config_valid(struct intel_dp *intel_dp, · line 582
Quoted 3 lines
drivers/gpu/drm/i915/intel_psr.c +3
-0+if (dev_priv->psr.pipe_crc_enabled) +return false; +Disabling PSR instead of switching to PSR1 is safer considering the past bug reports with PSR1.
Quoted 5 lines
I thought about that but it would break every PSR subtest in
kms_frontbuffer_tracking, I guess is better start by disabling PSR2 and
then discuss about PSR1 if decided to disable, we need to remove PSR1 fromkms_frontbuffer_trackingfirst.
I see.
Quoted 34 lines
Quoted 27 lines
Quoted 13 lines
drivers/gpu/drm/i915/intel_psr.c +2
-0return true; }@@ -1291,3 +1294,23 @@ bool intel_psr_enabled(struct intel_dp *intel_dp)return ret; } + +void intel_psr_crc_prepare_or_finish(struct drm_i915_private
*dev_priv, enum pipe pipe, bool prepare)drivers/gpu/drm/i915/intel_psr.c bool intel_psr_enabled(struct intel_dp *intel_dp) · line 1308
Quoted 10 lines
drivers/gpu/drm/i915/intel_psr.c +10
-0+{ +bool fastset = false; + +if (!CAN_PSR (dev_priv)) +return ; + +mutex_lock (&dev_priv->psr.lock); + +if (dev_priv->psr.pipe == pipe) { + dev_priv->psr.pipe_crc_enabled = prepare;.crc_enabled seems like it belongs in
crtc_staterather than in the global atomic state.Quoted 6 lines
Looks like we could rename and re-purpose crtc_state.ips_force_disable
for this. I don't see that flag being used for anything other working
around CRC issues.
Quoted 4 lines
My understanging is that we should not update
crtc_stateor any other state outside ofatomic_check()call chain, if that is not true I will
rename and reuseips_force_disable.
I don't see it being any different from modifying crtc_state->mode_changed to do a fastset. Besides that, all that needs to be done is rename the flag and shuffle the code a bit.
Quoted 15 lines
Quoted 10 lines
drivers/gpu/drm/i915/intel_psr.c bool intel_psr_enabled(struct intel_dp *intel_dp) · line 1316
Quoted 10 lines
drivers/gpu/drm/i915/intel_psr.c +8
-0+ fastset = !prepare || dev_priv->psr.psr2_enabled; + } + +mutex_unlock (&dev_priv->psr.lock); + +if (fastset) +intel_psr_fastset_force (dev_priv); +}_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 2/4] drm/i915: Disable PSR2 while getting pipe CRC
Quoted 171 lines · Dhinakaran Pandiyan
Quoted 122 lines · Jose
Quoted 113 lines · Dhinakaran Pandiyan
Quoted 112 lines · José Roberto de Souza
As stated in
CRC_CTLspec, after PSR entry state CRC will not be
calculated anymore what is not a problem as IGT tests do some screen
change and then request the pipe CRC right after the change so PSR
will go to idle state and only will entry again after at least 6
idles frames.But for PSR2 it is more problematic as any change to the screen could
trigger a selective/partial update causing the CRC value not to be
calculated over the full frame.So here it disables PSR2 and keep it disabled while user is requesting pipe CRC.
BSpec: 7536
Cc Dhinakaran Pandiyan <[email protected]>Cc Ville Syrjälä <[email protected]>Signed-off-by José Roberto de Souza <[email protected]>--- drivers/gpu/drm/i915/i915_drv.h | 1 + drivers/gpu/drm/i915/intel_drv.h | 1 + drivers/gpu/drm/i915/intel_pipe_crc.c | 10 ++++++++++ drivers/gpu/drm/i915/intel_psr.c | 23 +++++++++++++++++++++++ 4 files changed, 35 insertions(+)drivers/gpu/drm/i915/i915_drv.h +1
-0@@ -520,6 +520,7 @@ struct i915_psr {bool sink_not_reliable;bool irq_aux_error;u16 su_x_granularity; +bool pipe_crc_enabled; };enum intel_pch {drivers/gpu/drm/i915/intel_drv.h +0
-0@@ -2103,6 +2103,7 @@ void intel_psr_short_pulse(struct
intel_dp*intel_dp);
int intel_psr_wait_for_idle(const structintel_crtc_state*new_crtc_state,drivers/gpu/drm/i915/intel_drv.h +1
-0u32 *out_value);bool intel_psr_enabled (struct intel_dp *intel_dp); +void intel_psr_crc_prepare_or_finish(struct drm_i915_private
*dev_priv, enum pipe pipe, bool prepare);/*
intel_quirks.c*/
voidintel_init_quirks(struct drm_i915_private *dev_priv);drivers/gpu/drm/i915/intel_pipe_crc.c +0
-0@@ -583,6 +583,14 @@ int intel_crtc_verify_crc_source(struct
drm_crtc
*crtc, const char*source_name,drivers/gpu/drm/i915/intel_pipe_crc.c +1
-0return -EINVAL ; } +static inline void intel_crtc_crc_prepare_or_finish(struct
drm_crtc
*crtc, bool prepare)drivers/gpu/drm/i915/intel_pipe_crc.c +5
-0+{ +struct drm_i915_private *dev_priv =to_i915 (crtc->dev); +struct intel_crtc *intel_crtc =to_intel_crtc (crtc); + + intel_psr_crc_prepare_or_finish(dev_priv, intel_crtc-Quoted 1 line
pipe,
prepare);
drivers/gpu/drm/i915/intel_pipe_crc.c +2
-0+} + int intel_crtc_set_crc_source(struct drm_crtc *crtc, constchar
*source_name)
{drivers/gpu/drm/i915/intel_pipe_crc.c +0
-0struct drm_i915_private *dev_priv =to_i915 (crtc->dev);@@ -609,6 +617,8 @@ int intel_crtc_set_crc_source(struct
drm_crtc
*crtc, const char*source_name)drivers/gpu/drm/i915/intel_pipe_crc.c +1
-0if (ret !=0 ) goto out; + intel_crtc_crc_prepare_or_finish(crtc, source !=
INTEL_PIPE_CRC_SOURCE_NONE);drivers/gpu/drm/i915/intel_pipe_crc.c +1
-0+ pipe_crc->source = source;I915_WRITE (PIPE_CRC_CTL (crtc->index), val);POSTING_READ (PIPE_CRC_CTL (crtc->index));drivers/gpu/drm/i915/intel_psr.c +0
-0@@ -577,6 +577,9 @@ static bool intel_psr2_config_valid(structintel_dp *intel_dp, return false; }Quoted 7 lines
drivers/gpu/drm/i915/intel_psr.c static bool intel_psr2_config_valid(struct intel_dp *intel_dp, · line 582
Quoted 3 lines
drivers/gpu/drm/i915/intel_psr.c +3
-0+if (dev_priv->psr.pipe_crc_enabled) +return false; +Disabling PSR instead of switching to PSR1 is safer considering the
past bug reports with PSR1.Quoted 6 lines
I thought about that but it would break every PSR subtest in
kms_frontbuffer_tracking, I guess is better start by disabling PSR2 and
then discuss about PSR1 if decided to disable, we need to remove PSR1
fromkms_frontbuffer_trackingfirst.I see.
Quoted 34 lines
Quoted 27 lines
Quoted 12 lines
drivers/gpu/drm/i915/intel_psr.c +2
-0return true; }@@ -1291,3 +1294,23 @@ bool intel_psr_enabled(struct intel_dp *intel_dp)return ret; } + +void intel_psr_crc_prepare_or_finish(struct drm_i915_private
*dev_priv, enum pipe pipe, bool prepare)drivers/gpu/drm/i915/intel_psr.c bool intel_psr_enabled(struct intel_dp *intel_dp) · line 1308
Quoted 10 lines
drivers/gpu/drm/i915/intel_psr.c +10
-0+{ +bool fastset = false; + +if (!CAN_PSR (dev_priv)) +return ; + +mutex_lock (&dev_priv->psr.lock); + +if (dev_priv->psr.pipe == pipe) { + dev_priv->psr.pipe_crc_enabled = prepare;.crc_enabled seems like it belongs in
crtc_staterather than in the
global atomic state.Quoted 6 lines
Looks like we could rename and re-purpose crtc_state.ips_force_disable
for this. I don't see that flag being used for anything other working
around CRC issues.Quoted 5 lines
My understanging is that we should not update
crtc_stateor any other
state outside ofatomic_check()call chain, if that is not true I will
rename and reuseips_force_disable.
Quoted 4 lines
I don't see it being any different from modifying
crtc_state->mode_changedto do a fastset. Besides that, all that needs
to be done is rename the flag and shuffle the code a bit.
Ooh okay, I was thiking that you wanted to set it as psr.pipe_crc_enabled is set in this patch, okay I will do the shuffling and send other version.
Thanks for the review.
Quoted 15 lines
Quoted 15 lines
Quoted 10 lines
drivers/gpu/drm/i915/intel_psr.c bool intel_psr_enabled(struct intel_dp *intel_dp) · line 1316
Quoted 10 lines
drivers/gpu/drm/i915/intel_psr.c +1
-0+ fastset = !prepare || dev_priv-Quoted 1 line
psr.psr2_enabled;
drivers/gpu/drm/i915/intel_psr.c +7
-0+ } + +mutex_unlock (&dev_priv->psr.lock); + +if (fastset) +intel_psr_fastset_force (dev_priv); +}_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 3/4 drm/i915/psr: Remove PSR2 FIXME
In reply to José Roberto de SouzaNow we are checking sink capabilities when probing PSR DPCD register and then dynamically checking in if new state is compatible with PSR in, so this FIXME can be dropped.
--- drivers/gpu/drm/i915/intel_psr.c | 5 ----- 1 file changed, 5 deletions(-)
drivers/gpu/drm/i915/intel_psr.c +0 -5
@@ -532,11 +532,6 @@ static bool intel_psr2_config_valid(struct intel_dp *intel_dp,int crtc_vdisplay = crtc_state->base.adjusted_mode.crtc_vdisplay;int psr_max_h =0 , psr_max_v =0 ; -/* -* FIXME psr2_support is messed up. It's both computed -* dynamically during PSR enable, and extracted from sink -* caps during eDP detection. -*/ if (!dev_priv->psr.sink_psr2_support)return false;
Signature · 6 lines
2.20.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 4/4 drm/i915: Enable PSR2 by default
In reply to José Roberto de SouzaThe support for PSR2 was polished, IGT tests for PSR2 was added and it was tested performing regular user workloads like browsing, editing documents and compiling Linux, so it is time to enable it by default and enjoy even more power-savings.
---
We can hold this patch a little longer, I'm mainly sending it to show that 'drm/i915: Disable PSR2 while getting pipe CRC' fixed the CRC tests when PSR2 is enabled.
drivers/gpu/drm/i915/intel_psr.c | 3 --- 1 file changed, 3 deletions(-)
drivers/gpu/drm/i915/intel_psr.c +0 -3
@@ -80,9 +80,6 @@ static bool intel_psr2_enabled(struct drm_i915_private *dev_priv,case I915_PSR_DEBUG_DISABLE :case I915_PSR_DEBUG_FORCE_PSR1 :return false; -case I915_PSR_DEBUG_DEFAULT : -if (i915_modparams.enable_psr <=0 ) -return false;default :return crtc_state->has_psr2; }
Signature · 6 lines
2.20.1 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Patchwork
CI✗ Fi.CI.CHECKPATCH: warning for series starting with [1/4] drm/i915/psr: Only lookup for enabled CRTCs when forcing a fastset
In reply to José Roberto de Souza== Series Details ==
== Series Details ==
Series: series starting with [1/4] drm/i915/psr: Only lookup for enabled CRTCs when forcing a fastset
URL : https://patchwork.freedesktop.org/series/56647/
State : warning
== Summary ==
$ dim checkpatch origin/drm-tip e53ec9ed5dc6 drm/i915/psr: Only lookup for enabled CRTCs when forcing a fastset 441f8b87c393 drm/i915: Disable PSR2 while getting pipe CRC -:48: WARNING:LONG_LINE: line over 100 characters #48: FILE: drivers/gpu/drm/i915/intel_drv.h:2106: +void intel_psr_crc_prepare_or_finish(struct drm_i915_private *dev_priv, enum pipe pipe, bool prepare);
-:99: WARNING:LONG_LINE: line over 100 characters
#99: FILE: drivers/gpu/drm/i915/intel_psr.c:1298:
+void intel_psr_crc_prepare_or_finish(struct drm_i915_private *dev_priv, enum pipe pipe, bool prepare)
total: 0 errors, 2 warnings, 0 checks, 68 lines checked 727cc543561b drm/i915/psr: Remove PSR2 FIXME b912f44f1bf4 drm/i915: Enable PSR2 by default
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Patchwork
CI✗ Fi.CI.SPARSE: warning for series starting with [1/4] drm/i915/psr: Only lookup for enabled CRTCs when forcing a fastset
In reply to José Roberto de Souza== Series Details ==
== Series Details ==
Series: series starting with [1/4] drm/i915/psr: Only lookup for enabled CRTCs when forcing a fastset
URL : https://patchwork.freedesktop.org/series/56647/
State : warning
== Summary ==
$ dim sparse origin/drm-tip Sparse version: v0.5.2 Commit: drm/i915/psr: Only lookup for enabled CRTCs when forcing a fastset Okay!
Commit: drm/i915: Disable PSR2 while getting pipe CRC -drivers/gpu/drm/i915/selftests/../i915_drv.h:3566:16: warning: expression using sizeof(void) +drivers/gpu/drm/i915/selftests/../i915_drv.h:3567:16: warning: expression using sizeof(void)
Commit: drm/i915/psr: Remove PSR2 FIXME
Okay!
Commit: drm/i915: Enable PSR2 by default
Okay!
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Patchwork
CI✓ Fi.CI.BAT: success for series starting with [1/4] drm/i915/psr: Only lookup for enabled CRTCs when forcing a fastset
In reply to José Roberto de Souza== Series Details ==
== Series Details ==
Series: series starting with [1/4] drm/i915/psr: Only lookup for enabled CRTCs when forcing a fastset
URL : https://patchwork.freedesktop.org/series/56647/
State : success
== Summary ==
CI Bug Log - changes from CI_DRM_5601 -> Patchwork_12220
====================================================
Summary
-------
**SUCCESS**
No regressions found.
External URL: https://patchwork.freedesktop.org/api/1.0/series/56647/revisions/1/mbox/
Known issues
------------
Here are the changes found in Patchwork_12220 that come from known issues:
### IGT changes ###
#### Issues hit ####
* igt@amdgpu/amd_basic@cs-compute:
- fi-kbl-8809g: NOTRUN -> FAIL [fdo#108094]
* igt@i915_selftest@live_evict:
- fi-bsw-kefka: PASS -> DMESG-WARN [fdo#107709]
* igt@kms_pipe_crc_basic@hang-read-crc-pipe-b:
- fi-byt-clapper: PASS -> FAIL [fdo#103191] / [fdo#107362]
#### Possible fixes ####
* igt@amdgpu/amd_basic@userptr:
- fi-kbl-8809g: DMESG-WARN [fdo#108965] -> PASS
* igt@gem_exec_suspend@basic-s3:
- {fi-icl-u3}: FAIL [fdo#103375] -> PASS
* igt@gem_mmap_gtt@basic-small-bo:
- {fi-icl-u3}: DMESG-WARN [fdo#107724] -> PASS
* igt@i915_module_load@reload:
- fi-blb-e6850: INCOMPLETE [fdo#107718] -> PASS
* igt@kms_flip@basic-flip-vs-dpms:
- fi-skl-6700hq: DMESG-WARN [fdo#105998] -> PASS
* igt@kms_pipe_crc_basic@nonblocking-crc-pipe-a-frame-sequence:
- fi-byt-clapper: FAIL [fdo#103191] / [fdo#107362] -> PASS
* igt@kms_pipe_crc_basic@suspend-read-crc-pipe-a:
- fi-ivb-3520m: FAIL [fdo#103375] -> PASS
#### Warnings ####
* igt@kms_chamelium@common-hpd-after-suspend:
- fi-kbl-7567u: DMESG-WARN [fdo#103558] / [fdo#105079] / [fdo#105602] -> DMESG-FAIL [fdo#105079]
{name}: This element is suppressed. This means it is ignored when computing
the status of the difference (SUCCESS, WARNING, or FAILURE).
[fdo#103191]: https://bugs.freedesktop.org/show_bug.cgi?id=103191
[fdo#103375]: https://bugs.freedesktop.org/show_bug.cgi?id=103375
[fdo#103558]: https://bugs.freedesktop.org/show_bug.cgi?id=103558
[fdo#105079]: https://bugs.freedesktop.org/show_bug.cgi?id=105079
[fdo#105602]: https://bugs.freedesktop.org/show_bug.cgi?id=105602
[fdo#105998]: https://bugs.freedesktop.org/show_bug.cgi?id=105998
[fdo#107362]: https://bugs.freedesktop.org/show_bug.cgi?id=107362
[fdo#107709]: https://bugs.freedesktop.org/show_bug.cgi?id=107709
[fdo#107718]: https://bugs.freedesktop.org/show_bug.cgi?id=107718
[fdo#107724]: https://bugs.freedesktop.org/show_bug.cgi?id=107724
[fdo#108094]: https://bugs.freedesktop.org/show_bug.cgi?id=108094
[fdo#108622]: https://bugs.freedesktop.org/show_bug.cgi?id=108622
[fdo#108965]: https://bugs.freedesktop.org/show_bug.cgi?id=108965
[fdo#109271]: https://bugs.freedesktop.org/show_bug.cgi?id=109271
Participating hosts (50 -> 42)
------------------------------
Missing (8): fi-kbl-soraka fi-ilk-m540 fi-byt-squawks fi-bsw-cyan fi-glk-j4005 fi-gdg-551 fi-icl-y fi-bdw-samus
Build changes
-------------
* Linux: CI_DRM_5601 -> Patchwork_12220
CI_DRM_5601: 7977cc73f17770b9b1ed8baff66a8c9fd681d6a8 @ git://anongit.freedesktop.org/gfx-ci/linux
IGT_4827: 395eaffd7e1390c9d6043c2980dc14ce3e08b154 @ git://anongit.freedesktop.org/xorg/app/intel-gpu-tools
Patchwork_12220: b912f44f1bf4d36de451e198a419b937f0637cde @ git://anongit.freedesktop.org/gfx-ci/linux
== Linux commits ==
b912f44f1bf4 drm/i915: Enable PSR2 by default727cc543561b drm/i915/psr: Remove PSR2 FIXME441f8b87c393 drm/i915: Disable PSR2 while getting pipe CRC e53ec9ed5dc6 drm/i915/psr: Only lookup for enabled CRTCs when forcing a fastset
== Logs ==
For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_12220/
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Patchwork
CI✗ Fi.CI.IGT: failure for series starting with [1/4] drm/i915/psr: Only lookup for enabled CRTCs when forcing a fastset
In reply to José Roberto de Souza== Series Details ==
== Series Details ==
Series: series starting with [1/4] drm/i915/psr: Only lookup for enabled CRTCs when forcing a fastset
URL : https://patchwork.freedesktop.org/series/56647/
State : failure
== Summary ==
CI Bug Log - changes from CI_DRM_5601_full -> Patchwork_12220_full
====================================================
Summary
-------
**FAILURE**
Serious unknown changes coming with Patchwork_12220_full absolutely need to be verified manually.
If you think the reported changes have nothing to do with the changes introduced in Patchwork_12220_full, please notify your bug team to allow them to document this new failure mode, which will reduce false positives in CI.
Possible new issues
-------------------
Here are the unknown changes that may have been introduced in Patchwork_12220_full:
### IGT changes ###
#### Possible regressions ####
* igt@kms_vblank@pipe-b-ts-continuation-dpms-rpm:
- shard-apl: PASS -> FAIL
#### Suppressed ####
The following results come from untrusted machines, tests, or statuses. They do not affect the overall result.
* {igt@kms_psr2_su@frontbuffer}:
- shard-iclb: NOTRUN -> {SKIP}
Known issues
------------
Here are the changes found in Patchwork_12220_full that come from known issues:
### IGT changes ###
#### Issues hit ####
* igt@gem_eio@reset-stress:
- shard-snb: PASS -> FAIL [fdo#107799]
* igt@i915_selftest@live_workarounds:
- shard-iclb: PASS -> DMESG-FAIL [fdo#108954]
* igt@kms_atomic_transition@plane-all-modeset-transition-fencing:
- shard-apl: PASS -> INCOMPLETE [fdo#103927] / [fdo#109225]
* igt@kms_busy@extended-modeset-hang-newfb-render-b:
- shard-snb: NOTRUN -> DMESG-WARN [fdo#107956]
* igt@kms_ccs@pipe-b-crc-primary-basic:
- shard-iclb: NOTRUN -> FAIL [fdo#107725]
* igt@kms_color@pipe-b-ctm-0-75:
- shard-iclb: NOTRUN -> DMESG-WARN [fdo#109624]
* igt@kms_cursor_crc@cursor-128x128-suspend:
- shard-apl: PASS -> FAIL [fdo#103191] / [fdo#103232]
* igt@kms_cursor_crc@cursor-128x42-random:
- shard-apl: PASS -> FAIL [fdo#103232]
* igt@kms_frontbuffer_tracking@fbc-1p-primscrn-spr-indfb-draw-mmap-gtt:
- shard-glk: PASS -> FAIL [fdo#103167]
* igt@kms_frontbuffer_tracking@fbc-1p-primscrn-spr-indfb-draw-pwrite:
- shard-apl: PASS -> FAIL [fdo#103167] +1
* igt@kms_frontbuffer_tracking@psr-1p-primscrn-spr-indfb-fullscreen:
- shard-iclb: PASS -> FAIL [fdo#103167] +2
* igt@kms_plane@pixel-format-pipe-b-planes-source-clamping:
- shard-glk: PASS -> FAIL [fdo#108948]
* igt@kms_plane_alpha_blend@pipe-a-alpha-opaque-fb:
- shard-kbl: NOTRUN -> FAIL [fdo#108145]
* igt@kms_plane_alpha_blend@pipe-c-alpha-7efc:
- shard-kbl: NOTRUN -> FAIL [fdo#108145] / [fdo#108590]
* igt@kms_plane_multiple@atomic-pipe-b-tiling-none:
- shard-glk: PASS -> FAIL [fdo#103166]
* igt@kms_plane_multiple@atomic-pipe-c-tiling-y:
- shard-apl: PASS -> FAIL [fdo#103166]
* igt@kms_psr@no_drrs:
- shard-iclb: PASS -> FAIL [fdo#108341]
* igt@kms_rotation_crc@multiplane-rotation:
- shard-kbl: PASS -> FAIL [fdo#109016]
* igt@kms_setmode@basic:
- shard-apl: PASS -> FAIL [fdo#99912]
- shard-hsw: PASS -> FAIL [fdo#99912]
* igt@kms_sysfs_edid_timing:
- shard-kbl: NOTRUN -> FAIL [fdo#100047]
* igt@kms_vblank@pipe-b-ts-continuation-suspend:
- shard-apl: PASS -> DMESG-WARN [fdo#108566]
* igt@pm_rpm@cursor:
- shard-iclb: PASS -> DMESG-WARN [fdo#107724] +1
* igt@pm_rpm@legacy-planes:
- shard-iclb: PASS -> INCOMPLETE [fdo#108840] / [fdo#109369]
#### Possible fixes ####
* igt@kms_busy@extended-pageflip-modeset-hang-oldfb-render-b:
- shard-glk: DMESG-WARN [fdo#107956] -> PASS +1
* igt@kms_color@pipe-c-legacy-gamma:
- shard-glk: FAIL [fdo#104782] -> PASS
* igt@kms_cursor_crc@cursor-128x128-suspend:
- shard-kbl: DMESG-WARN [fdo#108566] -> PASS
* igt@kms_cursor_crc@cursor-128x42-onscreen:
- shard-apl: FAIL [fdo#103232] -> PASS +2
* igt@kms_flip@2x-flip-vs-expired-vblank:
- shard-glk: FAIL [fdo#102887] -> PASS
* igt@kms_frontbuffer_tracking@fbc-1p-primscrn-spr-indfb-draw-blt:
- shard-apl: FAIL [fdo#103167] -> PASS
* igt@kms_frontbuffer_tracking@fbc-2p-primscrn-spr-indfb-draw-mmap-cpu:
- shard-glk: FAIL [fdo#103167] -> PASS +2
* igt@kms_frontbuffer_tracking@fbcpsr-1p-primscrn-spr-indfb-fullscreen:
- shard-iclb: FAIL [fdo#103167] -> PASS
* igt@kms_sysfs_edid_timing:
- shard-iclb: FAIL [fdo#100047] -> PASS
* igt@kms_universal_plane@universal-plane-pipe-a-functional:
- shard-apl: FAIL [fdo#103166] -> PASS
* igt@pm_backlight@basic-brightness:
- shard-iclb: INCOMPLETE [fdo#107820] -> PASS
* igt@pm_rpm@debugfs-read:
- shard-iclb: DMESG-WARN [fdo#107724] -> PASS +4
* igt@pm_rpm@universal-planes:
- shard-iclb: DMESG-WARN [fdo#108654] / [fdo#108756] -> PASS
#### Warnings ####
* igt@kms_cursor_crc@cursor-256x256-suspend:
- shard-glk: FAIL [fdo#103232] -> INCOMPLETE [fdo#103359] / [k.org#198133]
* igt@pm_backlight@fade_with_suspend:
- shard-iclb: DMESG-FAIL [fdo#107724] / [fdo#107847] -> FAIL [fdo#107847]
{name}: This element is suppressed. This means it is ignored when computing
the status of the difference (SUCCESS, WARNING, or FAILURE).
[fdo#100047]: https://bugs.freedesktop.org/show_bug.cgi?id=100047
[fdo#102887]: https://bugs.freedesktop.org/show_bug.cgi?id=102887
[fdo#103166]: https://bugs.freedesktop.org/show_bug.cgi?id=103166
[fdo#103167]: https://bugs.freedesktop.org/show_bug.cgi?id=103167
[fdo#103191]: https://bugs.freedesktop.org/show_bug.cgi?id=103191
[fdo#103232]: https://bugs.freedesktop.org/show_bug.cgi?id=103232
[fdo#103359]: https://bugs.freedesktop.org/show_bug.cgi?id=103359
[fdo#103927]: https://bugs.freedesktop.org/show_bug.cgi?id=103927
[fdo#104782]: https://bugs.freedesktop.org/show_bug.cgi?id=104782
[fdo#107724]: https://bugs.freedesktop.org/show_bug.cgi?id=107724
[fdo#107725]: https://bugs.freedesktop.org/show_bug.cgi?id=107725
[fdo#107799]: https://bugs.freedesktop.org/show_bug.cgi?id=107799
[fdo#107820]: https://bugs.freedesktop.org/show_bug.cgi?id=107820
[fdo#107847]: https://bugs.freedesktop.org/show_bug.cgi?id=107847
[fdo#107956]: https://bugs.freedesktop.org/show_bug.cgi?id=107956
[fdo#108145]: https://bugs.freedesktop.org/show_bug.cgi?id=108145
[fdo#108341]: https://bugs.freedesktop.org/show_bug.cgi?id=108341
[fdo#108566]: https://bugs.freedesktop.org/show_bug.cgi?id=108566
[fdo#108590]: https://bugs.freedesktop.org/show_bug.cgi?id=108590
[fdo#108654]: https://bugs.freedesktop.org/show_bug.cgi?id=108654
[fdo#108756]: https://bugs.freedesktop.org/show_bug.cgi?id=108756
[fdo#108840]: https://bugs.freedesktop.org/show_bug.cgi?id=108840
[fdo#108948]: https://bugs.freedesktop.org/show_bug.cgi?id=108948
[fdo#108954]: https://bugs.freedesktop.org/show_bug.cgi?id=108954
[fdo#109016]: https://bugs.freedesktop.org/show_bug.cgi?id=109016
[fdo#109225]: https://bugs.freedesktop.org/show_bug.cgi?id=109225
[fdo#109271]: https://bugs.freedesktop.org/show_bug.cgi?id=109271
[fdo#109274]: https://bugs.freedesktop.org/show_bug.cgi?id=109274
[fdo#109276]: https://bugs.freedesktop.org/show_bug.cgi?id=109276
[fdo#109278]: https://bugs.freedesktop.org/show_bug.cgi?id=109278
[fdo#109280]: https://bugs.freedesktop.org/show_bug.cgi?id=109280
[fdo#109281]: https://bugs.freedesktop.org/show_bug.cgi?id=109281
[fdo#109289]: https://bugs.freedesktop.org/show_bug.cgi?id=109289
[fdo#109290]: https://bugs.freedesktop.org/show_bug.cgi?id=109290
[fdo#109291]: https://bugs.freedesktop.org/show_bug.cgi?id=109291
[fdo#109292]: https://bugs.freedesktop.org/show_bug.cgi?id=109292
[fdo#109307]: https://bugs.freedesktop.org/show_bug.cgi?id=109307
[fdo#109308]: https://bugs.freedesktop.org/show_bug.cgi?id=109308
[fdo#109369]: https://bugs.freedesktop.org/show_bug.cgi?id=109369
[fdo#109624]: https://bugs.freedesktop.org/show_bug.cgi?id=109624
[fdo#99912]: https://bugs.freedesktop.org/show_bug.cgi?id=99912
[k.org#198133]: https://bugzilla.kernel.org/show_bug.cgi?id=198133
Participating hosts (7 -> 6)
------------------------------
Missing (1): shard-skl
Build changes
-------------
* Linux: CI_DRM_5601 -> Patchwork_12220
CI_DRM_5601: 7977cc73f17770b9b1ed8baff66a8c9fd681d6a8 @ git://anongit.freedesktop.org/gfx-ci/linux
IGT_4827: 395eaffd7e1390c9d6043c2980dc14ce3e08b154 @ git://anongit.freedesktop.org/xorg/app/intel-gpu-tools
Patchwork_12220: b912f44f1bf4d36de451e198a419b937f0637cde @ git://anongit.freedesktop.org/gfx-ci/linux
piglit_4509: fdc5a4ca11124ab8413c7988896eec4c97336694 @ git://anongit.freedesktop.org/piglit
== Logs ==
For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_12220/
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoted 7 lines · José Roberto de Souza
Forcing a specific CRTC to the eDP connector was causing the
intel_psr_fastset_force()to markmode_chagedin the wrong and disabled CRTC causing no update in the PSR state.Looks like our internal state track do not clear
output_typesandhas_psrin the disabled CRTCs, not sure if this is the expected behavior or not but in the mean time this fix the issue.
Is there an IGT that's failing because of this? Looks like the state would have got cleared only if the crtc was enabled to drive another encoder.
Quoted 26 lines
Cc Maarten Lankhorst <[email protected]>Cc Dhinakaran Pandiyan <[email protected]>Signed-off-by José Roberto de Souza <[email protected]>--- drivers/gpu/drm/i915/intel_psr.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)drivers/gpu/drm/i915/intel_psr.c +0
-1@@ -986,7 +986,8 @@ static int intel_psr_fastset_force(struct drm_i915_private *dev_priv) intel_crtc_state =to_intel_crtc_state (crtc_state); - if (intel_crtc_has_type(intel_crtc_state,
INTEL_OUTPUT_EDP) &&drivers/gpu/drm/i915/intel_psr.c +2
-0+if (crtc_state->enable && + intel_crtc_has_type(intel_crtc_state,
INTEL_OUTPUT_EDP) &&drivers/gpu/drm/i915/intel_psr.c +0
-0intel_crtc_state->has_psr) {/* Mark mode as changed to trigger a pipe- Quoted 1 line
update()*/
Quoted 1 line
crtc_state->mode_changed= true;
I was wondering if we should remove the 'break;' that follows instead and let ->update_pipe take care of the rest. However, checking crtc_state->enable makes sense as there is not much point in triggering a fastset on a disabled crtc.
There might be a better way to do this, so please double check with someone :)
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoted 5 lines · Dhinakaran
Quoted 4 lines · José Roberto de Souza
Forcing a specific CRTC to the eDP connector was causing the
intel_psr_fastset_force()to markmode_chagedin the wrong and disabled CRTC causing no update in the PSR state.
Quoted 7 lines
Quoted 3 lines
Looks like our internal state track do not clear
output_typesandhas_psrin the disabled CRTCs, not sure if this is the expected behavior or not but in the mean time this fix the issue.Is there an IGT that's failing because of this? Looks like the state would have got cleared only if the crtc was enabled to drive another encoder.
When PSR2 is enabled by default tests like kms_pipe_crc_basic@read-crc-pipe-b are failling even with the patch that disable PSR2 when getting CRC.
Quoted 33 lines
Quoted 26 lines
Cc Maarten Lankhorst <[email protected]>Cc Dhinakaran Pandiyan <[email protected]>Signed-off-by José Roberto de Souza <[email protected]>--- drivers/gpu/drm/i915/intel_psr.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)drivers/gpu/drm/i915/intel_psr.c +0
-1@@ -986,7 +986,8 @@ static int intel_psr_fastset_force(struct drm_i915_private *dev_priv) intel_crtc_state =to_intel_crtc_state (crtc_state); - if (intel_crtc_has_type(intel_crtc_state,
INTEL_OUTPUT_EDP) &&drivers/gpu/drm/i915/intel_psr.c +2
-0+if (crtc_state->enable && + intel_crtc_has_type(intel_crtc_state,
INTEL_OUTPUT_EDP) &&drivers/gpu/drm/i915/intel_psr.c +0
-0intel_crtc_state->has_psr) {/* Mark mode as changed to trigger a pipe- Quoted 1 line
update()*/Quoted 1 line
crtc_state->mode_changed= true;I was wondering if we should remove the 'break;' that follows instead and let ->update_pipe take care of the rest. However, checking
crtc_state->enablemakes sense as there is not much point in triggering
a fastset on a disabled crtc.
Quoted 5 lines
Reviewed-by Dhinakaran Pandiyan <[email protected]>There might be a better way to do this, so please double check with someone :)
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoted 16 lines · Jose
Quoted 9 lines · Dhinakaran
Quoted 7 lines · José Roberto de Souza
Forcing a specific CRTC to the eDP connector was causing the
intel_psr_fastset_force()to markmode_chagedin the wrong and disabled CRTC causing no update in the PSR state.Looks like our internal state track do not clear
output_typesandhas_psrin the disabled CRTCs, not sure if this is the expected behavior or not but in the mean time this fix the issue.Quoted 5 lines
Is there an IGT that's failing because of this? Looks like the state
would have got cleared only if the crtc was enabled to drive another
encoder.
Quoted 3 lines
When PSR2 is enabled by default tests like kms_pipe_crc_basic@read-crc-pipe-b are failling even with the patch that disable PSR2 when getting CRC.
Thanks!
Quoted 17 lines
Quoted 17 lines
Quoted 17 lines
Cc Maarten Lankhorst <[email protected]>Cc Dhinakaran Pandiyan <[email protected]>Signed-off-by José Roberto de Souza <[email protected]>--- drivers/gpu/drm/i915/intel_psr.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)drivers/gpu/drm/i915/intel_psr.c +0
-0@@ -986,7 +986,8 @@ static int intel_psr_fastset_force(struct drm_i915_private *dev_priv)
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
drivers/gpu/drm/i915/intel_psr.c +0
-1intel_crtc_state =to_intel_crtc_state (crtc_state); - if (intel_crtc_has_type(intel_crtc_state,
INTEL_OUTPUT_EDP) &&drivers/gpu/drm/i915/intel_psr.c +2
-0+if (crtc_state->enable && + intel_crtc_has_type(intel_crtc_state,
INTEL_OUTPUT_EDP) &&
intel_crtc_state->has_psr) {
if (crtc_state->enable && intel_crtc_state->has_psr)
should cover all the cases, no?
And also add a WARN() in case we somehow end up with more than once crtc with the above condition being true.
Quoted 12 lines
Quoted 12 lines
Quoted 4 lines
/* Mark mode as changed to trigger a pipe-
Quoted 1 line
update()*/
crtc_state->mode_changed= true;I was wondering if we should remove the 'break;' that follows instead
and let ->update_pipe take care of the rest. However, checkingcrtc_state->enablemakes sense as there is not much point in triggering
a fastset on a disabled crtc.
Quoted 5 lines
Quoted 5 lines
Reviewed-by Dhinakaran Pandiyan <[email protected]>There might be a better way to do this, so please double check with someone :)
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Op 23-02-2019 om 03:02 schreef Dhinakaran Pandiyan:
Quoted 47 lines · Jose
Quoted 9 lines · Dhinakaran
Quoted 8 lines · José Roberto de Souza
Quoted 7 lines
Forcing a specific CRTC to the eDP connector was causing the
intel_psr_fastset_force()to markmode_chagedin the wrong and disabled CRTC causing no update in the PSR state.Looks like our internal state track do not clear
output_typesandhas_psrin the disabled CRTCs, not sure if this is the expected behavior or not but in the mean time this fix the issue.Quoted 8 lines
Quoted 5 lines
Is there an IGT that's failing because of this? Looks like the state
would have got cleared only if the crtc was enabled to drive another
encoder.When PSR2 is enabled by default tests like kms_pipe_crc_basic@read-crc-pipe-b are failling even with the patch that disable PSR2 when getting CRC.
Thanks!
Quoted 15 lines
Quoted 15 lines
Quoted 15 lines
Cc Maarten Lankhorst <[email protected]>Cc Dhinakaran Pandiyan <[email protected]>Signed-off-by José Roberto de Souza <[email protected]>--- drivers/gpu/drm/i915/intel_psr.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)drivers/gpu/drm/i915/intel_psr.c +0
-0@@ -986,7 +986,8 @@ static int intel_psr_fastset_force(struct drm_i915_private *dev_priv)Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
drivers/gpu/drm/i915/intel_psr.c +0
-1intel_crtc_state =to_intel_crtc_state (crtc_state); - if (intel_crtc_has_type(intel_crtc_state,
INTEL_OUTPUT_EDP) &&drivers/gpu/drm/i915/intel_psr.c +2
-0+if (crtc_state->enable && + intel_crtc_has_type(intel_crtc_state,
INTEL_OUTPUT_EDP) &&
intel_crtc_state->has_psr) {if (
crtc_state->enable&&intel_crtc_state->has_psr)
should cover all the cases, no?
Quoted 2 lines
And also add a
WARN()in case we somehow end up with more than once crtc with the above condition being true.
Please use crtc_state->active
crtc_state->enable only tells if the crtc is configured. It doesn't mean thatthe pipe is running.
~Maarten
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx