Skip to contentSkip to conversation

Trouble reading from my serial device (a microcontroller)

DISCUSSION Chuck Messenger 1 participant 2 messages Nov 20, 2003 TTY layer and serial drivers

lore
Share & tools
lore
#0 lore raw

I'm unable to read from a serial device under Linux (Mandrake 9.1, 2.4.21-0.13mdk kernel), but the device works find in Windows. I'm hoping someone can offer me suggestions.

My device is a Basic Stamp microcontroller, which I've programmed to spit out a certain byte continuously -- 0x40 -- at 38400 baud,n,8,1. The device loops RTS back to DSR (i.e. it connects pins 6 and 7 of the 9-pin serial connector -- DSR and RTS). Other than that, only Rx and Tx are connected (and ground, of course).

I know the hardware works (both controller and PC), because I can boot Win2k on the same machine and run a short program I wrote which continuously dumps to the console whatever comes in.

Also, I know that things are _basically_ configured right, in my Linux boot, since I can run "statserial /dev/tts/0", which shows, in real time, the status of the DSR line. When I unplug from my device, DSR goes low; when I plug it back in, DSR goes high.

I tried writing a simple port-dumping program on Linux, based on Peter Baumann's sample in his Serial Programming Howto:

#include <sys/types.h>
#include <sys/stat.h>
#include <fcntl.h>
#include <termios.h>
#include <stdio.h>

#define BAUDRATE B38400
#define MODEMDEVICE "/dev/tts/0"
#define _POSIX_SOURCE 1 /* POSIX compliant source */

int
main()

{
    int fd,c, res;
    struct termios oldtio,newtio;

    fd = open(MODEMDEVICE, O_RDWR | O_NOCTTY );

    if (fd < 0) {
        perror(MODEMDEVICE);
        exit(-1);
    }

    tcgetattr(fd, &oldtio); /* save current port settings */

    memset(&newtio, 0, sizeof(newtio));

    newtio.c_cflag = BAUDRATE | /*CRTSCTS |*/ CS8 | CLOCAL | CREAD;
    newtio.c_iflag = IGNPAR   // ignore parity errors
                   | IGNBRK;  // ignore BREAK characters
    newtio.c_oflag = 0;

    /* set input mode (non-canonical, no echo,...) */

    newtio.c_lflag = 0;

    newtio.c_cc[VTIME]    = 0;   /* inter-character timer unused */
    newtio.c_cc[VMIN]     = 1;   /* blocking read until 1 chars received */

    tcflush(fd, TCIFLUSH);       // Flush an data received by not read
    tcsetattr(fd,TCSANOW,&newtio);

    while (1) {       /* loop for input */
        char buf[1];
        res = read(fd,buf,1);   /* returns after 1 chars have been input */
        printf("%02x ", buf[0]);
        fflush(stdout);
    }

    tcsetattr(fd,TCSANOW,&oldtio);

    return 0;
}

However, the program fails to read any bytes -- it hangs at the read().

I've tried running serlook, but that, too, failed to see any bytes.

Any suggestions?

I've tried 9600 baud instead of 38400 -- still no luck (although it works under Win2k).

Poking around, I've seen mention of the DCD control line -- could that be the problem (i.e. does the Linux serial driver require it, somehow? I don't have it hooked up.)

- Chuck Messenger

#1 lore raw

OK, I figured it out. Yeah, I'm having a conversation with myself. But maybe it'll help someone else with the same problem who finds this message on a search.

The answer turned out to be: set DCD high. DCD is pin 1 on a 9-pin serial connector. That was all there was to it. The program I included below works fine. But if DCD isn't high (in my case, it wasn't connected), then read() will hang indefinitely.

I had read here and there that open() would hang if DCD wasn't high, depending on the flags (that is, unless O_NONBLOCKING was used). However, I found that open() didn't hang.

To recap: If you're trying to connect to a simple serial device, and all you connect is Tx, Rx and ground, then you may find (as I did) that read() will hang. You also must connect DCD (pin 1) to +12 V (I put it through a 2.2k resistor, just in case...).

- Happy Chuck

Quoted 84 lines · Chuck Messenger

I'm unable to read from a serial device under Linux (Mandrake 9.1, 2.4.21-0.13mdk kernel), but the device works find in Windows. I'm hoping someone can offer me suggestions.

My device is a Basic Stamp microcontroller, which I've programmed to spit out a certain byte continuously -- 0x40 -- at 38400 baud,n,8,1. The device loops RTS back to DSR (i.e. it connects pins 6 and 7 of the 9-pin serial connector -- DSR and RTS). Other than that, only Rx and Tx are connected (and ground, of course).

I know the hardware works (both controller and PC), because I can boot Win2k on the same machine and run a short program I wrote which continuously dumps to the console whatever comes in.

Also, I know that things are _basically_ configured right, in my Linux boot, since I can run "statserial /dev/tts/0", which shows, in real time, the status of the DSR line. When I unplug from my device, DSR goes low; when I plug it back in, DSR goes high.

I tried writing a simple port-dumping program on Linux, based on Peter Baumann's sample in his Serial Programming Howto:

#include <sys/types.h>
#include <sys/stat.h>
#include <fcntl.h>
#include <termios.h>
#include <stdio.h>

#define BAUDRATE B38400
#define MODEMDEVICE "/dev/tts/0"
#define _POSIX_SOURCE 1 /* POSIX compliant source */

int
main()

{
    int fd,c, res;
    struct termios oldtio,newtio;

    fd = open(MODEMDEVICE, O_RDWR | O_NOCTTY );

    if (fd < 0) {
        perror(MODEMDEVICE);
        exit(-1);
    }

    tcgetattr(fd, &oldtio); /* save current port settings */

    memset(&newtio, 0, sizeof(newtio));

    newtio.c_cflag = BAUDRATE | /*CRTSCTS |*/ CS8 | CLOCAL | CREAD;
    newtio.c_iflag = IGNPAR   // ignore parity errors
                   | IGNBRK;  // ignore BREAK characters
    newtio.c_oflag = 0;

    /* set input mode (non-canonical, no echo,...) */

    newtio.c_lflag = 0;

    newtio.c_cc[VTIME]    = 0;   /* inter-character timer unused */
    newtio.c_cc[VMIN]     = 1;   /* blocking read until 1 chars received */

    tcflush(fd, TCIFLUSH);       // Flush an data received by not read
    tcsetattr(fd,TCSANOW,&newtio);

    while (1) {       /* loop for input */
        char buf[1];
        res = read(fd,buf,1);   /* returns after 1 chars have been input */
        printf("%02x ", buf[0]);
        fflush(stdout);
    }

    tcsetattr(fd,TCSANOW,&oldtio);

    return 0;
}

However, the program fails to read any bytes -- it hangs at the read().

I've tried running serlook, but that, too, failed to see any bytes.

Any suggestions?

I've tried 9600 baud instead of 38400 -- still no luck (although it works under Win2k).

Poking around, I've seen mention of the DCD control line -- could that be the problem (i.e. does the Linux serial driver require it, somehow? I don't have it hooked up.)

- Chuck Messenger

-
To unsubscribe from this list: send the line "unsubscribe linux-serial" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html