New: SAMA5D3-Xplained Default configuration can't start U-Boot
https://bugs.busybox.net/show_bug.cgi?id=12846
Bug ID: 12846
Summary: SAMA5D3-Xplained Default configuration can't start
U-Boot
Product: buildroot
Version: 2020.02.1
Hardware: Other
OS: Linux
Status: NEW
Severity: normal
Priority: P5
Component: Other
Assignee: unassigned at buildroot.uclibc.org
Reporter: therealergo at gmail.com
CC: buildroot at uclibc.org
Target Milestone: ---
OS: Ubuntu 20.04 LTS
Following the instructions in board/atmel/readme.txt for the SAMA5D3-Xplained boot from NAND with either atmel_sama5d3_xplained_defconfig or atmel_sama5d3_xplained_dev_defconfig, the image does not boot past AT91Bootstrap.
Only the following is output from the board:
RomBOOT
AT91Bootstrap 3.9.0 (Sat 02 May 2020 09:50:11 PM CDT)
ACT8865: Set REG1/REG2/REG3 Power-saving mode
ACT8865: Disable ACT8865's I2C interface
NAND: ONFI flash detected
NAND: Manufacturer ID: 0x2c Chip ID: 0xda
NAND: Page Bytes: 2048, Spare Bytes: 64
NAND: ECC Correctability Bits: 4, ECC Sector Bytes: 512
NAND: Disable On-Die ECC
NAND: Initialize PMECC params, cap: 4, sector: 512
NAND: Image: Copy 0xc0000 bytes from 0x40000 to 0x26f00000
NAND: Done to load image
However, when the U-Boot version is changed to "linux4sam_5.5" by changing the "U-Boot Version" from "Custom tarball" to "Custon Git Repository," changing "URL of custom repository" to "https://github.com/linux4sam/u-boot-at91.git" and changing "Custom repository version" to "801b789," the image boots successfully.
I've done the debugging that I can, and I'm certain that AT91Bootstrap is copying the U-Boot image into RAM and jumping to it, but I haven't been able to narrow down the issue any further.
Steps to reproduce:
Quoted 6 lines
make
atmel_sama5d3_xplained_defconfig
make
Put board into RomBOOT (open JP5, power up, close JP5)./board/atmel/flasher.sh./output/dev/ttyACM0sama5d3_xplained(flash completes successfully)
Restart board
Signature · 2 lines
You are receiving this mail because: You are on the CC list for the bug.
[Buildroot] [Bug 12846] SAMA5D3-Xplained Default configuration can't start U-Boot
https://bugs.busybox.net/show_bug.cgi?id=12846
Thomas Petazzoni <[email protected]> changed:
What |Removed |Added
----------------------------------------------------------------------------
Assignee|unassigned at buildroot.uclibc |ludovic.desroches at atmel.com
|.org |
--- Comment #1 from Thomas Petazzoni <[email protected]> --- Ludovic, could you have a look ?
Signature · 2 lines
You are receiving this mail because: You are on the CC list for the bug.
[Buildroot] [Bug 12846] SAMA5D3-Xplained Default configuration can't start U-Boot
In reply to bugzilla at busybox.nethttps://bugs.busybox.net/show_bug.cgi?id=12846
Yann E. MORIN <[email protected]> changed:
What |Removed |Added
----------------------------------------------------------------------------
Resolution|--- |MOVED
CC| |[email protected]
Status|NEW |RESOLVED--- Comment #2 from Yann E. MORIN <[email protected]> --- Thank you for your report.
The issue tracker for the Buildroot project has been moved to the Gitlab.com issue tracker:
https://gitlab.com/buildroot.org/buildroot/-/issues
We are taking this opportunity to close old issues in this old tracker. If you believe your issue is still relevant, please open one in the new issue tracker.
Thank you!
Signature · 6 lines
You are receiving this mail because: You are on the CC list for the bug. _______________________________________________ buildroot mailing list [email protected] https://lists.buildroot.org/mailman/listinfo/buildroot