watchdog: K3: Add RTI watchdog support
Subsystems (2)
v2 cover watchdog: K3: Add RTI watchdog support
This brings watchdog support for the TI K3 SoCs, derived from the Linux kernel, augmented with firmware loading as needed on the AM65x.
Tested on the AM65x EVM and the IOT2050 (also AM65x-based, upstream support will be posted soon).
Changes in v2:
- keep watchdog powered when handing over to Linux
- drop unneeded explicit power-on
- account for RTI firmware locking the power domain
Jan
Jan Kiszka (3):
watchdog: Add support for K3 RTI watchdog
watchdog: rti_wdt: Add support for loading firmware
arm: dts: k3: Add RTI watchdogs
arch/arm/dts/k3-am65-mcu.dtsi | 9 ++ arch/arm/dts/k3-j721e-main.dtsi | 18 ++++ drivers/watchdog/Kconfig | 27 ++++++ drivers/watchdog/Makefile | 4 + drivers/watchdog/rti_wdt.c | 147 ++++++++++++++++++++++++++++++++ drivers/watchdog/rti_wdt_fw.S | 20 +++++ 6 files changed, 225 insertions(+) create mode 100644 drivers/watchdog/rti_wdt.c create mode 100644 drivers/watchdog/rti_wdt_fw.S
Signature · 1 line
2.26.2
PATCH v2 1/3 watchdog: Add support for K3 RTI watchdog
From: Jan Kiszka <[email protected]>
This is based on the Linux kernel driver for the RTI watchdog.
To actually reset the system on an AM65x, it requires firmware running on the R5 that accepts the NMI and issues the actual system reset via TISCI. Kind of an iTCO, except that this watchdog hardware has support for no-way-out, and only for that.
On the J721E, reset works without extra firmware help when routing the RTI interrupt via the ESM.
--- drivers/watchdog/Kconfig | 7 +++ drivers/watchdog/Makefile | 1 + drivers/watchdog/rti_wdt.c | 123 +++++++++++++++++++++++++++++++++++++ 3 files changed, 131 insertions(+) create mode 100644 drivers/watchdog/rti_wdt.c
drivers/watchdog/Kconfig +7 -0
@@ -155,6 +155,13 @@ config WDT_ORION Select this to enable Orion watchdog timer, which can be found on some Marvell Armada chips. +config WDT_K3_RTI + bool "Texas Instruments K3 RTI watchdog" + depends on WDT && ARCH_K3 + help + Say Y here if you want to include support for the K3 watchdog + timer (RTI module) available in the K3 generation of processors. + config WDT_SANDBOX bool "Enable Watchdog Timer support for Sandbox" depends on SANDBOX && WDT
drivers/watchdog/Makefile +1 -0
@@ -27,6 +27,7 @@ obj-$(CONFIG_WDT_MPC8xx) += mpc8xx_wdt.o obj-$(CONFIG_WDT_MT7621) += mt7621_wdt.o obj-$(CONFIG_WDT_MTK) += mtk_wdt.o obj-$(CONFIG_WDT_OMAP3) += omap_wdt.o +obj-$(CONFIG_WDT_K3_RTI) += rti_wdt.o obj-$(CONFIG_WDT_SP805) += sp805_wdt.o obj-$(CONFIG_WDT_STM32MP) += stm32mp_wdt.o obj-$(CONFIG_WDT_TANGIER) += tangier_wdt.o
drivers/watchdog/rti_wdt.c new file +123 -0
123 lines not on this page · raw message
Signature · 1 line
2.26.2
PATCH v2 1/3 watchdog: Add support for K3 RTI watchdog
Quoted 111 lines · Jan Kiszka
From: Jan Kiszka <[email protected]>
This is based on the Linux kernel driver for the RTI watchdog.
To actually reset the system on an AM65x, it requires firmware running on the R5 that accepts the NMI and issues the actual system reset via TISCI. Kind of an iTCO, except that this watchdog hardware has support for no-way-out, and only for that.
On the J721E, reset works without extra firmware help when routing the RTI interrupt via the ESM.
Signed-off-by Jan Kiszka <[email protected]>--- drivers/watchdog/Kconfig | 7 +++ drivers/watchdog/Makefile | 1 + drivers/watchdog/rti_wdt.c | 123 +++++++++++++++++++++++++++++++++++++ 3 files changed, 131 insertions(+) create mode 100644 drivers/watchdog/rti_wdt.cdrivers/watchdog/Kconfig +7
-0@@ -155,6 +155,13 @@ config WDT_ORION Select this to enable Orion watchdog timer, which can be found on some Marvell Armada chips. +config WDT_K3_RTI + bool "Texas Instruments K3 RTI watchdog" + depends on WDT && ARCH_K3 + help + Say Y here if you want to include support for the K3 watchdog + timer (RTI module) available in the K3 generation of processors. + config WDT_SANDBOX bool "Enable Watchdog Timer support for Sandbox" depends on SANDBOX && WDTdrivers/watchdog/Makefile +1
-0@@ -27,6 +27,7 @@ obj-$(CONFIG_WDT_MPC8xx) += mpc8xx_wdt.o obj-$(CONFIG_WDT_MT7621) += mt7621_wdt.o obj-$(CONFIG_WDT_MTK) += mtk_wdt.o obj-$(CONFIG_WDT_OMAP3) += omap_wdt.o +obj-$(CONFIG_WDT_K3_RTI) += rti_wdt.o obj-$(CONFIG_WDT_SP805) += sp805_wdt.o obj-$(CONFIG_WDT_STM32MP) += stm32mp_wdt.o obj-$(CONFIG_WDT_TANGIER) += tangier_wdt.odrivers/watchdog/rti_wdt.c new file +55
-0@@ -0,0 +1,123 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* Copyright (c) Siemens AG, 2020 +* +* Authors: +* Jan Kiszka <[email protected]> +* +* Derived from linux/drivers/watchdog/rti_wdt.c +*/ + +#include <common.h> +#include <clk.h> +#include <dm.h> +#include <power-domain.h> +#include <wdt.h> +#include <asm/io.h> + +/* Timer register set definition */ +#define RTIDWDCTRL 0x90 +#define RTIDWDPRLD 0x94 +#define RTIWDSTATUS 0x98 +#define RTIWDKEY 0x9c +#define RTIDWDCNTR 0xa0 +#define RTIWWDRXCTRL 0xa4 +#define RTIWWDSIZECTRL 0xa8 + +#define RTIWWDRX_NMI 0xa + +#define RTIWWDSIZE_50P 0x50 + +#define WDENABLE_KEY 0xa98559da + +#define WDKEY_SEQ0 0xe51a +#define WDKEY_SEQ1 0xa35c + +#define WDT_PRELOAD_SHIFT 13 + +#define WDT_PRELOAD_MAX 0xfff + +struct rti_wdt_priv { +phys_addr_t regs; +unsigned int clk_khz; +}; + +static int rti_wdt_start (struct udevice *dev,u64 timeout_ms,ulong flags) +{ +struct rti_wdt_priv *priv =dev_get_priv (dev); +u32 timer_margin; +int ret; + +if (readl (priv->regs +RTIDWDCTRL ) ==WDENABLE_KEY ) +return -EBUSY ; + + timer_margin = timeout_ms * priv->clk_khz /1000 ; + timer_margin >>=WDT_PRELOAD_SHIFT ;
drivers/watchdog/rti_wdt.c line 65
Quoted 10 lines
drivers/watchdog/rti_wdt.c new file +10
-0+if (timer_margin >WDT_PRELOAD_MAX ) + timer_margin =WDT_PRELOAD_MAX ; + +writel (timer_margin, priv->regs +RTIDWDPRLD ); +writel (RTIWWDRX_NMI , priv->regs +RTIWWDRXCTRL ); +writel (RTIWWDSIZE_50P , priv->regs +RTIWWDSIZECTRL ); + +readl (priv->regs +RTIWWDSIZECTRL ); + +writel (WDENABLE_KEY , priv->regs +RTIDWDCTRL );
What happens if the watchdog timer expires in U-Boot?
Is the watchdog started from U-Boot command line?
Quoted 36 lines
drivers/watchdog/rti_wdt.c new file +36
-0+ +return 0 ; +} + +static int rti_wdt_reset (struct udevice *dev) +{ +struct rti_wdt_priv *priv =dev_get_priv (dev); +u32 prld; + +/* Make sure we do not reset too early */ + prld =readl (priv->regs +RTIDWDPRLD ) <<WDT_PRELOAD_SHIFT ; +if (readl (priv->regs +RTIDWDCNTR ) >= prld /2 ) +return -EPERM ; + +writel (WDKEY_SEQ0 , priv->regs +RTIWDKEY ); +writel (WDKEY_SEQ1 , priv->regs +RTIWDKEY ); + +return 0 ; +} + +static int rti_wdt_probe (struct udevice *dev) +{ +struct rti_wdt_priv *priv =dev_get_priv (dev); +struct clk clk; +int ret; + + priv->regs =devfdt_get_addr (dev); +if (!priv->regs) +return -EINVAL ; + + ret =clk_get_by_index (dev,0 , &clk); +if (ret) +return ret; + + priv->clk_khz =clk_get_rate (&clk); +
drivers/watchdog/rti_wdt.c line 111
Quoted 10 lines
drivers/watchdog/rti_wdt.c new file +10
-0+return 0 ; +} + +static const struct wdt_ops rti_wdt_ops = { + .start = rti_wdt_start, + .reset = rti_wdt_reset, +}; + +static const struct udevice_id rti_wdt_ids[] = { + { .compatible ="ti,j7-rti-wdt" },
Is this compatible matching with Kernel's compatible?
Thanks and regards,
Lokesh
PATCH v2 1/3 watchdog: Add support for K3 RTI watchdog
Quoted 118 lines · Lokesh Vutla
Quoted 115 lines · Jan Kiszka
From: Jan Kiszka <[email protected]>
This is based on the Linux kernel driver for the RTI watchdog.
To actually reset the system on an AM65x, it requires firmware running on the R5 that accepts the NMI and issues the actual system reset via TISCI. Kind of an iTCO, except that this watchdog hardware has support for no-way-out, and only for that.
On the J721E, reset works without extra firmware help when routing the RTI interrupt via the ESM.
Signed-off-by Jan Kiszka <[email protected]>--- drivers/watchdog/Kconfig | 7 +++ drivers/watchdog/Makefile | 1 + drivers/watchdog/rti_wdt.c | 123 +++++++++++++++++++++++++++++++++++++ 3 files changed, 131 insertions(+)create mode 100644
drivers/watchdog/rti_wdt.cdrivers/watchdog/Kconfig +7
-0@@ -155,6 +155,13 @@ config WDT_ORION Select this to enable Orion watchdog timer, which can be found on some Marvell Armada chips. +config WDT_K3_RTI + bool "Texas Instruments K3 RTI watchdog" + depends on WDT && ARCH_K3 + help + Say Y here if you want to include support for the K3 watchdog + timer (RTI module) available in the K3 generation of processors. + config WDT_SANDBOX bool "Enable Watchdog Timer support for Sandbox" depends on SANDBOX && WDTdrivers/watchdog/Makefile +1
-0@@ -27,6 +27,7 @@ obj-$(CONFIG_WDT_MPC8xx) += mpc8xx_wdt.o obj-$(CONFIG_WDT_MT7621) += mt7621_wdt.o obj-$(CONFIG_WDT_MTK) += mtk_wdt.o obj-$(CONFIG_WDT_OMAP3) += omap_wdt.o +obj-$(CONFIG_WDT_K3_RTI) += rti_wdt.o obj-$(CONFIG_WDT_SP805) += sp805_wdt.o obj-$(CONFIG_WDT_STM32MP) += stm32mp_wdt.o obj-$(CONFIG_WDT_TANGIER) += tangier_wdt.odrivers/watchdog/rti_wdt.c new file +59
-0@@ -0,0 +1,123 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* Copyright (c) Siemens AG, 2020 +* +* Authors: +* Jan Kiszka <[email protected]> +* +* Derived from linux/drivers/watchdog/rti_wdt.c +*/ + +#include <common.h> +#include <clk.h> +#include <dm.h> +#include <power-domain.h> +#include <wdt.h> +#include <asm/io.h> + +/* Timer register set definition */ +#define RTIDWDCTRL 0x90 +#define RTIDWDPRLD 0x94 +#define RTIWDSTATUS 0x98 +#define RTIWDKEY 0x9c +#define RTIDWDCNTR 0xa0 +#define RTIWWDRXCTRL 0xa4 +#define RTIWWDSIZECTRL 0xa8 + +#define RTIWWDRX_NMI 0xa + +#define RTIWWDSIZE_50P 0x50 + +#define WDENABLE_KEY 0xa98559da + +#define WDKEY_SEQ0 0xe51a +#define WDKEY_SEQ1 0xa35c + +#define WDT_PRELOAD_SHIFT 13 + +#define WDT_PRELOAD_MAX 0xfff + +struct rti_wdt_priv { +phys_addr_t regs; +unsigned int clk_khz; +}; + +static int rti_wdt_start (struct udevice *dev,u64 timeout_ms,ulong flags) +{ +struct rti_wdt_priv *priv =dev_get_priv (dev); +u32 timer_margin; +int ret; + +if (readl (priv->regs +RTIDWDCTRL ) ==WDENABLE_KEY ) +return -EBUSY ; + + timer_margin = timeout_ms * priv->clk_khz /1000 ; + timer_margin >>=WDT_PRELOAD_SHIFT ; +if (timer_margin >WDT_PRELOAD_MAX ) + timer_margin =WDT_PRELOAD_MAX ; + +writel (timer_margin, priv->regs +RTIDWDPRLD );
Quoted 9 lines
drivers/watchdog/rti_wdt.c line 65
Quoted 6 lines
drivers/watchdog/rti_wdt.c new file +6
-0+writel (RTIWWDRX_NMI , priv->regs +RTIWWDRXCTRL ); +writel (RTIWWDSIZE_50P , priv->regs +RTIWWDSIZECTRL ); + +readl (priv->regs +RTIWWDSIZECTRL ); + +writel (WDENABLE_KEY , priv->regs +RTIDWDCTRL );What happens if the watchdog timer expires in U-Boot?
Then we reset. You can feed the watchdog also from U-Boot, just enable CONFIG_WATCHDOG.
Quoted 2 lines
Is the watchdog started from U-Boot command line?
U-Boot automatically starts the first watchdog it finds. I didn't find a switch to disable that. If you have multiple watchdogs, you can start others also via "wdt".
Quoted 40 lines
Quoted 40 lines
drivers/watchdog/rti_wdt.c new file +40
-0+ +return 0 ; +} + +static int rti_wdt_reset (struct udevice *dev) +{ +struct rti_wdt_priv *priv =dev_get_priv (dev); +u32 prld; + +/* Make sure we do not reset too early */ + prld =readl (priv->regs +RTIDWDPRLD ) <<WDT_PRELOAD_SHIFT ; +if (readl (priv->regs +RTIDWDCNTR ) >= prld /2 ) +return -EPERM ; + +writel (WDKEY_SEQ0 , priv->regs +RTIWDKEY ); +writel (WDKEY_SEQ1 , priv->regs +RTIWDKEY ); + +return 0 ; +} + +static int rti_wdt_probe (struct udevice *dev) +{ +struct rti_wdt_priv *priv =dev_get_priv (dev); +struct clk clk; +int ret; + + priv->regs =devfdt_get_addr (dev); +if (!priv->regs) +return -EINVAL ; + + ret =clk_get_by_index (dev,0 , &clk); +if (ret) +return ret; + + priv->clk_khz =clk_get_rate (&clk); + +return 0 ; +} + +static const struct wdt_ops rti_wdt_ops = {
Quoted 9 lines
drivers/watchdog/rti_wdt.c line 111
Quoted 6 lines
drivers/watchdog/rti_wdt.c new file +6
-0+ .start = rti_wdt_start, + .reset = rti_wdt_reset, +}; + +static const struct udevice_id rti_wdt_ids[] = { + { .compatible ="ti,j7-rti-wdt" },Is this compatible matching with Kernel's compatible?
Yes.
Jan
Signature · 2 lines
Siemens AG, Corporate Technology, CT RDA IOT SES-DE Corporate Competence Center Embedded Linux
PATCH v2 2/3 watchdog: rti_wdt: Add support for loading firmware
In reply to Jan KiszkaFrom: Jan Kiszka <[email protected]>
To avoid the need of extra boot scripting on AM65x for loading a watchdog firmware, add the required rproc init and loading logic for the first R5F core to the watchdog start handler. The firmware itself is embedded into U-Boot binary.
One possible firmware source is https://github.com/siemens/k3-rti-wdt.
--- drivers/watchdog/Kconfig | 20 ++++++++++++++++++++ drivers/watchdog/Makefile | 3 +++ drivers/watchdog/rti_wdt.c | 24 ++++++++++++++++++++++++ drivers/watchdog/rti_wdt_fw.S | 20 ++++++++++++++++++++ 4 files changed, 67 insertions(+) create mode 100644 drivers/watchdog/rti_wdt_fw.S
drivers/watchdog/Kconfig +20 -0
@@ -162,6 +162,26 @@ config WDT_K3_RTI Say Y here if you want to include support for the K3 watchdog timer (RTI module) available in the K3 generation of processors. +if WDT_K3_RTI + +config WDT_K3_RTI_LOAD_FW + bool "Load watchdog firmware" + depends on REMOTEPROC + help + Automatically load the specified firmware image into the MCU R5F + core 0. On the AM65x, this firmware is supposed to handle the expiry + of the watchdog timer, typically by resetting the system. + +config WDT_K3_RTI_FW_FILE + string "Watchdog firmware image file" + default "k3-rti-wdt.fw" + depends on WDT_K3_RTI_LOAD_FW + help + Firmware image to be embedded into U-Boot and loaded on watchdog + start. + +endif + config WDT_SANDBOX bool "Enable Watchdog Timer support for Sandbox" depends on SANDBOX && WDT
drivers/watchdog/Makefile +3 -0
@@ -28,7 +28,10 @@ obj-$(CONFIG_WDT_MT7621) += mt7621_wdt.o obj-$(CONFIG_WDT_MTK) += mtk_wdt.o obj-$(CONFIG_WDT_OMAP3) += omap_wdt.o obj-$(CONFIG_WDT_K3_RTI) += rti_wdt.o +obj-$(CONFIG_WDT_K3_RTI_LOAD_FW) += rti_wdt_fw.o obj-$(CONFIG_WDT_SP805) += sp805_wdt.o obj-$(CONFIG_WDT_STM32MP) += stm32mp_wdt.o obj-$(CONFIG_WDT_TANGIER) += tangier_wdt.o obj-$(CONFIG_WDT_XILINX) += xilinx_wwdt.o + +$(obj)/rti_wdt_fw.o: $(shell readlink -f $(CONFIG_WDT_K3_RTI_FW_FILE)) FORCE
drivers/watchdog/rti_wdt.c +24 -0
@@ -14,6 +14,7 @@#include <power-domain.h> #include <wdt.h> #include <asm/io.h> +#include <remoteproc.h> /* Timer register set definition */ #define RTIDWDCTRL 0x90
@@ -37,11 +38,16 @@#define WDT_PRELOAD_MAX 0xfff +#define RTI_PROC_ID 0 +struct rti_wdt_priv {phys_addr_t regs;unsigned int clk_khz; }; +extern const u32 rti_wdt_fw[]; +extern const int rti_wdt_fw_size; +static int rti_wdt_start (struct udevice *dev,u64 timeout_ms,ulong flags) {struct rti_wdt_priv *priv =dev_get_priv (dev);
@@ -51,6 +57,24 @@ static int rti_wdt_start(struct udevice *dev, u64 timeout_ms, ulong flags)if (readl (priv->regs +RTIDWDCTRL ) ==WDENABLE_KEY )return -EBUSY ; +#ifdef CONFIG_WDT_K3_RTI_LOAD_FW + ret =rproc_dev_init (RTI_PROC_ID ); +if (ret) { + fw_error: +dev_err (dev,"Failed to load watchdog firmware into remote processor %d\n" , +RTI_PROC_ID ); +return ret; + } + + ret =rproc_load (RTI_PROC_ID , (ulong )rti_wdt_fw, rti_wdt_fw_size); +if (ret) + goto fw_error; + + ret =rproc_start (RTI_PROC_ID ); +if (ret) + goto fw_error; +#endif + timer_margin = timeout_ms * priv->clk_khz /1000 ; timer_margin >>=WDT_PRELOAD_SHIFT ;if (timer_margin >WDT_PRELOAD_MAX )
drivers/watchdog/rti_wdt_fw.S new file +20 -0
@@ -0,0 +1,20 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (c) Siemens AG, 2020 + * + * Authors: + * Jan Kiszka <[email protected]> + */ + +.section .rodata + +.global rti_wdt_fw +.global rti_wdt_fw_size + +rti_wdt_fw: +.align 4 +.incbin CONFIG_WDT_K3_RTI_FW_FILE +rti_wdt_fw_end: + +rti_wdt_fw_size: +.int rti_wdt_fw_end - rti_wdt_fw
Signature · 1 line
2.26.2
PATCH v2 2/3 watchdog: rti_wdt: Add support for loading firmware
Quoted 77 lines · Jan Kiszka
From: Jan Kiszka <[email protected]>
To avoid the need of extra boot scripting on AM65x for loading a watchdog firmware, add the required rproc init and loading logic for the first R5F core to the watchdog start handler. The firmware itself is embedded into U-Boot binary.
One possible firmware source is https://github.com/siemens/k3-rti-wdt.
Signed-off-by Jan Kiszka <[email protected]>--- drivers/watchdog/Kconfig | 20 ++++++++++++++++++++ drivers/watchdog/Makefile | 3 +++ drivers/watchdog/rti_wdt.c | 24 ++++++++++++++++++++++++ drivers/watchdog/rti_wdt_fw.S | 20 ++++++++++++++++++++ 4 files changed, 67 insertions(+) create mode 100644 drivers/watchdog/rti_wdt_fw.Sdrivers/watchdog/Kconfig +20
-0@@ -162,6 +162,26 @@ config WDT_K3_RTI Say Y here if you want to include support for the K3 watchdog timer (RTI module) available in the K3 generation of processors. +if WDT_K3_RTI + +config WDT_K3_RTI_LOAD_FW + bool "Load watchdog firmware" + depends on REMOTEPROC + help + Automatically load the specified firmware image into the MCU R5F + core 0. On the AM65x, this firmware is supposed to handle the expiry + of the watchdog timer, typically by resetting the system. + +config WDT_K3_RTI_FW_FILE + string "Watchdog firmware image file" + default "k3-rti-wdt.fw" + depends on WDT_K3_RTI_LOAD_FW + help + Firmware image to be embedded into U-Boot and loaded on watchdog + start. + +endif + config WDT_SANDBOX bool "Enable Watchdog Timer support for Sandbox" depends on SANDBOX && WDTdrivers/watchdog/Makefile +3
-0@@ -28,7 +28,10 @@ obj-$(CONFIG_WDT_MT7621) += mt7621_wdt.o obj-$(CONFIG_WDT_MTK) += mtk_wdt.o obj-$(CONFIG_WDT_OMAP3) += omap_wdt.o obj-$(CONFIG_WDT_K3_RTI) += rti_wdt.o +obj-$(CONFIG_WDT_K3_RTI_LOAD_FW) += rti_wdt_fw.o obj-$(CONFIG_WDT_SP805) += sp805_wdt.o obj-$(CONFIG_WDT_STM32MP) += stm32mp_wdt.o obj-$(CONFIG_WDT_TANGIER) += tangier_wdt.o obj-$(CONFIG_WDT_XILINX) += xilinx_wwdt.o + +$(obj)/rti_wdt_fw.o: $(shell readlink -f $(CONFIG_WDT_K3_RTI_FW_FILE)) FORCEdrivers/watchdog/rti_wdt.c +1
-0@@ -14,6 +14,7 @@#include <power-domain.h> #include <wdt.h> #include <asm/io.h> +#include <remoteproc.h> /* Timer register set definition */ #define RTIDWDCTRL 0x90
drivers/watchdog/rti_wdt.c line 41
Quoted 4 lines
drivers/watchdog/rti_wdt.c +1
-0@@ -37,11 +38,16 @@#define WDT_PRELOAD_MAX 0xfff +#define RTI_PROC_ID 0
Can we get the rproc id from DT?
drivers/watchdog/rti_wdt.c line 49
Quoted 8 lines
drivers/watchdog/rti_wdt.c +3
-0+struct rti_wdt_priv {phys_addr_t regs;unsigned int clk_khz; }; +extern const u32 rti_wdt_fw[]; +extern const int rti_wdt_fw_size;
FIT is the preferred way of packing images in U-Boot. Can you try using it?
Thanks and regards,
Lokesh
PATCH v2 2/3 watchdog: rti_wdt: Add support for loading firmware
Quoted 81 lines · Lokesh Vutla
Quoted 78 lines · Jan Kiszka
From: Jan Kiszka <[email protected]>
To avoid the need of extra boot scripting on AM65x for loading a watchdog firmware, add the required rproc init and loading logic for the first R5F core to the watchdog start handler. The firmware itself is embedded into U-Boot binary.
One possible firmware source is https://github.com/siemens/k3-rti-wdt.
Signed-off-by Jan Kiszka <[email protected]>--- drivers/watchdog/Kconfig | 20 ++++++++++++++++++++ drivers/watchdog/Makefile | 3 +++ drivers/watchdog/rti_wdt.c | 24 ++++++++++++++++++++++++ drivers/watchdog/rti_wdt_fw.S | 20 ++++++++++++++++++++ 4 files changed, 67 insertions(+)create mode 100644
drivers/watchdog/rti_wdt_fw.Sdrivers/watchdog/Kconfig +20
-0@@ -162,6 +162,26 @@ config WDT_K3_RTI Say Y here if you want to include support for the K3 watchdog timer (RTI module) available in the K3 generation of processors. +if WDT_K3_RTI + +config WDT_K3_RTI_LOAD_FW + bool "Load watchdog firmware" + depends on REMOTEPROC + help + Automatically load the specified firmware image into the MCU R5F + core 0. On the AM65x, this firmware is supposed to handle the expiry + of the watchdog timer, typically by resetting the system. + +config WDT_K3_RTI_FW_FILE + string "Watchdog firmware image file" + default "k3-rti-wdt.fw" + depends on WDT_K3_RTI_LOAD_FW + help + Firmware image to be embedded into U-Boot and loaded on watchdog + start. + +endif + config WDT_SANDBOX bool "Enable Watchdog Timer support for Sandbox" depends on SANDBOX && WDTdrivers/watchdog/Makefile +3
-0@@ -28,7 +28,10 @@ obj-$(CONFIG_WDT_MT7621) += mt7621_wdt.o obj-$(CONFIG_WDT_MTK) += mtk_wdt.o obj-$(CONFIG_WDT_OMAP3) += omap_wdt.o obj-$(CONFIG_WDT_K3_RTI) += rti_wdt.o +obj-$(CONFIG_WDT_K3_RTI_LOAD_FW) += rti_wdt_fw.o obj-$(CONFIG_WDT_SP805) += sp805_wdt.o obj-$(CONFIG_WDT_STM32MP) += stm32mp_wdt.o obj-$(CONFIG_WDT_TANGIER) += tangier_wdt.o obj-$(CONFIG_WDT_XILINX) += xilinx_wwdt.o + +$(obj)/rti_wdt_fw.o: $(shell readlink -f $(CONFIG_WDT_K3_RTI_FW_FILE)) FORCEdrivers/watchdog/rti_wdt.c +1
-0@@ -14,6 +14,7 @@#include <power-domain.h> #include <wdt.h> #include <asm/io.h> +#include <remoteproc.h> /* Timer register set definition */ #define RTIDWDCTRL 0x90@@ -37,11 +38,16 @@
Quoted 5 lines
drivers/watchdog/rti_wdt.c line 41
Quoted 3 lines
drivers/watchdog/rti_wdt.c +1
-0#define WDT_PRELOAD_MAX 0xfff +#define RTI_PROC_ID 0Can we get the rproc id from DT?
You mean, resolve "mcu_r5fss0_core0" to the ID? Doable.
Quoted 11 lines
drivers/watchdog/rti_wdt.c line 49
Quoted 9 lines
drivers/watchdog/rti_wdt.c +3
-0+struct rti_wdt_priv {phys_addr_t regs;unsigned int clk_khz; }; +extern const u32 rti_wdt_fw[]; +extern const int rti_wdt_fw_size;FIT is the preferred way of packing images in U-Boot. Can you try using it?
How does that work? Some example for me?
What benefit would that bring? There are other users of this pattern, e.g. board/xilinx/zynqmp/pm_cfg_obj.S.
Jan
Signature · 2 lines
Siemens AG, Corporate Technology, CT RDA IOT SES-DE Corporate Competence Center Embedded Linux
PATCH v2 2/3 watchdog: rti_wdt: Add support for loading firmware
Quoted 86 lines · Jan Kiszka
Quoted 76 lines · Lokesh Vutla
Quoted 73 lines · Jan Kiszka
From: Jan Kiszka <[email protected]>
To avoid the need of extra boot scripting on AM65x for loading a watchdog firmware, add the required rproc init and loading logic for the first R5F core to the watchdog start handler. The firmware itself is embedded into U-Boot binary.
One possible firmware source is https://github.com/siemens/k3-rti-wdt.
Signed-off-by Jan Kiszka <[email protected]>---
? drivers/watchdog/Kconfig????? | 20 ++++++++++++++++++++ ? drivers/watchdog/Makefile???? |? 3 +++ ? drivers/watchdog/rti_wdt.c??? | 24 ++++++++++++++++++++++++ ? drivers/watchdog/rti_wdt_fw.S | 20 ++++++++++++++++++++? 4 files changed, 67 insertions(+)
? create mode 100644drivers/watchdog/rti_wdt_fw.Sdrivers/watchdog/Kconfig +0
-0@@ -162,6 +162,26 @@ config WDT_K3_RTI??????? Say Y here if you want to include support for the K3 watchdog ??????? timer (RTI module) available in the K3 generation of processors.
drivers/watchdog/Kconfig +8
-0+if WDT_K3_RTI + +config WDT_K3_RTI_LOAD_FW +??? bool "Load watchdog firmware" +??? depends on REMOTEPROC +??? help +????? Automatically load the specified firmware image into the MCU R5F +????? core 0. On the AM65x, this firmware is supposed to handle theexpiry
+????? of the watchdog timer, typically by resetting the system.drivers/watchdog/Kconfig +11
-0+ +config WDT_K3_RTI_FW_FILE +??? string "Watchdog firmware image file" +??? default "k3-rti-wdt.fw" +??? depends on WDT_K3_RTI_LOAD_FW +??? help +????? Firmware image to be embedded into U-Boot and loaded on watchdog +????? start. + +endif +? config
WDT_SANDBOX
????? bool "Enable Watchdog Timer support for Sandbox" ????? depends on SANDBOX && WDTdrivers/watchdog/Makefile +0
-0@@ -28,7 +28,10 @@ obj-$(CONFIG_WDT_MT7621) += mt7621_wdt.o? obj-$(CONFIG_WDT_MTK) += mtk_wdt.o
? obj-$(CONFIG_WDT_OMAP3) += omap_wdt.o
? obj-$(CONFIG_WDT_K3_RTI) += rti_wdt.o
+obj-$(CONFIG_WDT_K3_RTI_LOAD_FW) += rti_wdt_fw.o
? obj-$(CONFIG_WDT_SP805) += sp805_wdt.o
? obj-$(CONFIG_WDT_STM32MP) += stm32mp_wdt.o
? obj-$(CONFIG_WDT_TANGIER) += tangier_wdt.o
? obj-$(CONFIG_WDT_XILINX) += xilinx_wwdt.o
+
+$(obj)/rti_wdt_fw.o: $(shell readlink -f
$(CONFIG_WDT_K3_RTI_FW_FILE)) FORCEdrivers/watchdog/rti_wdt.c +0
-0@@ -14,6 +14,7 @@? #include <
power-domain.h>
? #include <wdt.h>
? #include <asm/io.h>Quoted 8 lines
Quoted 6 lines
+#include <
remoteproc.h>
? /* Timer register set definition */
? #define RTIDWDCTRL???????0x90drivers/watchdog/rti_wdt.c +0
-0@@ -37,11 +38,16 @@? #define
WDT_PRELOAD_MAX???????0xfff
+#defineRTI_PROC_ID??????? 0Can we get the rproc id from DT?
Quoted 2 lines
You mean, resolve "
mcu_r5fss0_core0" to the ID? Doable.
I'm now probing for the first instance of "ti,am654-r5f" compatible. That excludes usage for the J721E for now, but that one is fine without firmware - provided there is way to prevent power-down for RTI watchdog otherwise...
Quoted 12 lines
Quoted 11 lines
drivers/watchdog/rti_wdt.c line 49
Quoted 8 lines
+
? structrti_wdt_priv{
?????phys_addr_tregs;
????? unsigned intclk_khz;
? };drivers/watchdog/rti_wdt.c +2
-0+extern const u32 rti_wdt_fw[]; +extern const int rti_wdt_fw_size;FIT is the preferred way of packing images in U-Boot. Can you try using it?
Quoted 2 lines
How does that work? Some example for me?
If you happen to refer to fs-loader: That does not target OSPI, our primary use case.
Quoted 3 lines
What benefit would that bring? There are other users of this pattern, e.g.
board/xilinx/zynqmp/pm_cfg_obj.S.
The only benefit of an alternative loading mechanism seems to be handling of larger images from different sources. But that's what I would tackle via boot scripting and, thus, without this feature. If you only have a few hundred bytes to embed, like for k3-rti-wdt, you quickly have a lot of overhead with other approaches.
Jan
Signature · 2 lines
Siemens AG, Corporate Technology, CT RDA IOT SES-DE Corporate Competence Center Embedded Linux
PATCH v2 2/3 watchdog: rti_wdt: Add support for loading firmware
+Tom
Quoted 85 lines · Jan Kiszka
Quoted 84 lines · Jan Kiszka
Quoted 82 lines · Lokesh Vutla
Quoted 75 lines · Jan Kiszka
From: Jan Kiszka <[email protected]>
To avoid the need of extra boot scripting on AM65x for loading a watchdog firmware, add the required rproc init and loading logic for the first R5F core to the watchdog start handler. The firmware itself is embedded into U-Boot binary.
One possible firmware source is https://github.com/siemens/k3-rti-wdt.
Signed-off-by Jan Kiszka <[email protected]>---
? drivers/watchdog/Kconfig????? | 20 ++++++++++++++++++++ ? drivers/watchdog/Makefile???? |? 3 +++ ? drivers/watchdog/rti_wdt.c??? | 24 ++++++++++++++++++++++++ ? drivers/watchdog/rti_wdt_fw.S | 20 ++++++++++++++++++++? 4 files changed, 67 insertions(+)
? create mode 100644drivers/watchdog/rti_wdt_fw.Sdrivers/watchdog/Kconfig +0
-0@@ -162,6 +162,26 @@ config WDT_K3_RTI??????? Say Y here if you want to include support for the K3 watchdog ??????? timer (RTI module) available in the K3 generation of processors.
drivers/watchdog/Kconfig +20
-0+if WDT_K3_RTI + +config WDT_K3_RTI_LOAD_FW +??? bool "Load watchdog firmware" +??? depends on REMOTEPROC +??? help +????? Automatically load the specified firmware image into the MCU R5F +????? core 0. On the AM65x, this firmware is supposed to handle the expiry +????? of the watchdog timer, typically by resetting the system. + +config WDT_K3_RTI_FW_FILE +??? string "Watchdog firmware image file" +??? default "k3-rti-wdt.fw" +??? depends on WDT_K3_RTI_LOAD_FW +??? help +????? Firmware image to be embedded into U-Boot and loaded on watchdog +????? start. + +endif +? config
WDT_SANDBOX
????? bool "Enable Watchdog Timer support for Sandbox" ????? depends on SANDBOX && WDTdrivers/watchdog/Makefile +0
-0@@ -28,7 +28,10 @@ obj-$(CONFIG_WDT_MT7621) += mt7621_wdt.o? obj-$(CONFIG_WDT_MTK) += mtk_wdt.o
? obj-$(CONFIG_WDT_OMAP3) += omap_wdt.o
? obj-$(CONFIG_WDT_K3_RTI) += rti_wdt.o
+obj-$(CONFIG_WDT_K3_RTI_LOAD_FW) += rti_wdt_fw.o
? obj-$(CONFIG_WDT_SP805) += sp805_wdt.o
? obj-$(CONFIG_WDT_STM32MP) += stm32mp_wdt.o
? obj-$(CONFIG_WDT_TANGIER) += tangier_wdt.o
? obj-$(CONFIG_WDT_XILINX) += xilinx_wwdt.odrivers/watchdog/Makefile +2
-0+ +$(obj)/rti_wdt_fw.o: $(shell readlink -f $(CONFIG_WDT_K3_RTI_FW_FILE)) FORCEdrivers/watchdog/rti_wdt.c +0
-0@@ -14,6 +14,7 @@? #include <
power-domain.h>
? #include <wdt.h>
? #include <asm/io.h>
+#include <remoteproc.h>
? /* Timer register set definition */
? #define RTIDWDCTRL???????0x90drivers/watchdog/rti_wdt.c +0
-0@@ -37,11 +38,16 @@Quoted 2 lines
? #define
WDT_PRELOAD_MAX???????0xfff
+#defineRTI_PROC_ID??????? 0Can we get the rproc id from DT?
Quoted 6 lines
Quoted 2 lines
You mean, resolve "
mcu_r5fss0_core0" to the ID? Doable.I'm now probing for the first instance of "ti,am654-r5f" compatible. That excludes usage for the J721E for now, but that one is fine without firmware - provided there is way to prevent power-down for RTI watchdog otherwise...
I was more of thinking to have a DT property to reference R5-core. But anyways, the property is not present in kernel. I am okay with this for now.
Quoted 12 lines
Quoted 12 lines
Quoted 11 lines
drivers/watchdog/rti_wdt.c line 49
Quoted 9 lines
+
? structrti_wdt_priv{
?????phys_addr_tregs;
????? unsigned intclk_khz;
? };drivers/watchdog/rti_wdt.c +2
-0+extern const u32 rti_wdt_fw[]; +extern const int rti_wdt_fw_size;FIT is the preferred way of packing images in U-Boot. Can you try using it?
Quoted 5 lines
Quoted 2 lines
How does that work? Some example for me?
If you happen to refer to fs-loader: That does not target OSPI, our primary use case.
No. I was thinking to pack the image in FIT along with ATF and OPTEE like in k3_fit_atf.sh and register a U_BOOT_FIT_LOADABLE_HANDLER for installing the firmware.
Quoted 3 lines
Quoted 3 lines
What benefit would that bring? There are other users of this pattern, e.g.
board/xilinx/zynqmp/pm_cfg_obj.S.
I didn't know U-Boot is accepting this. Tom, is this the preferred way for including firmware images?
Quoted 7 lines
Quoted 1 line
The only benefit of an alternative loading mechanism seems to be handling of larger images from different sources. But that's what I would tackle via boot scripting and, thus, without this feature. If you only have a few hundred bytes to embed, like for k3-rti-wdt, you quickly have a lot of overhead with other approaches.
hmm.. Does the build break if firmware is not present?
Thanks and regards,
Lokesh
Quoted 3 lines
Jan
PATCH v2 2/3 watchdog: rti_wdt: Add support for loading firmware
Quoted 113 lines · Lokesh Vutla
+Tom
Quoted 85 lines · Jan Kiszka
Quoted 84 lines · Jan Kiszka
Quoted 82 lines · Lokesh Vutla
Quoted 75 lines · Jan Kiszka
From: Jan Kiszka <[email protected]>
To avoid the need of extra boot scripting on AM65x for loading a watchdog firmware, add the required rproc init and loading logic for the first R5F core to the watchdog start handler. The firmware itself is embedded into U-Boot binary.
One possible firmware source is https://github.com/siemens/k3-rti-wdt.
Signed-off-by Jan Kiszka <[email protected]>--- ? drivers/watchdog/Kconfig????? | 20 ++++++++++++++++++++ ? drivers/watchdog/Makefile???? |? 3 +++ ? drivers/watchdog/rti_wdt.c??? | 24 ++++++++++++++++++++++++ ? drivers/watchdog/rti_wdt_fw.S | 20 ++++++++++++++++++++? 4 files changed, 67 insertions(+)
? create mode 100644drivers/watchdog/rti_wdt_fw.Sdrivers/watchdog/Kconfig +20
-0@@ -162,6 +162,26 @@ config WDT_K3_RTI ??????? Say Y here if you want to include support for the K3 watchdog ??????? timer (RTI module) available in the K3 generation of processors. +if WDT_K3_RTI + +config WDT_K3_RTI_LOAD_FW +??? bool "Load watchdog firmware" +??? depends on REMOTEPROC +??? help +????? Automatically load the specified firmware image into the MCU R5F +????? core 0. On the AM65x, this firmware is supposed to handle the expiry +????? of the watchdog timer, typically by resetting the system. + +config WDT_K3_RTI_FW_FILE +??? string "Watchdog firmware image file" +??? default "k3-rti-wdt.fw" +??? depends on WDT_K3_RTI_LOAD_FW +??? help +????? Firmware image to be embedded into U-Boot and loaded on watchdog +????? start. + +endif + ? config WDT_SANDBOX ????? bool "Enable Watchdog Timer support for Sandbox" ????? depends on SANDBOX && WDTdrivers/watchdog/Makefile +3
-0@@ -28,7 +28,10 @@ obj-$(CONFIG_WDT_MT7621) += mt7621_wdt.o ? obj-$(CONFIG_WDT_MTK) += mtk_wdt.o ? obj-$(CONFIG_WDT_OMAP3) += omap_wdt.o ? obj-$(CONFIG_WDT_K3_RTI) += rti_wdt.o +obj-$(CONFIG_WDT_K3_RTI_LOAD_FW) += rti_wdt_fw.o ? obj-$(CONFIG_WDT_SP805) += sp805_wdt.o ? obj-$(CONFIG_WDT_STM32MP) += stm32mp_wdt.o ? obj-$(CONFIG_WDT_TANGIER) += tangier_wdt.o ? obj-$(CONFIG_WDT_XILINX) += xilinx_wwdt.o + +$(obj)/rti_wdt_fw.o: $(shell readlink -f $(CONFIG_WDT_K3_RTI_FW_FILE)) FORCEdrivers/watchdog/rti_wdt.c +1
-0@@ -14,6 +14,7 @@ ? #include <power-domain.h> ? #include <wdt.h> ? #include <asm/io.h> +#include <remoteproc.h> ? /* Timer register set definition */ ? #define RTIDWDCTRL??????? 0x90drivers/watchdog/rti_wdt.c line 39
Quoted 2 lines
drivers/watchdog/rti_wdt.c +1
-0@@ -37,11 +38,16 @@ ? #define WDT_PRELOAD_MAX??????? 0xfff +#define RTI_PROC_ID ??????? 0Can we get the rproc id from DT?
Quoted 6 lines
Quoted 2 lines
You mean, resolve "
mcu_r5fss0_core0" to the ID? Doable.I'm now probing for the first instance of "ti,am654-r5f" compatible. That excludes usage for the J721E for now, but that one is fine without firmware - provided there is way to prevent power-down for RTI watchdog otherwise...
I was more of thinking to have a DT property to reference R5-core. But anyways, the property is not present in kernel. I am okay with this for now.
Quoted 15 lines
Quoted 14 lines
Quoted 11 lines
drivers/watchdog/rti_wdt.c line 46
Quoted 9 lines
drivers/watchdog/rti_wdt.c +3
-0+ ? struct rti_wdt_priv { ????? phys_addr_t regs; ????? unsigned int clk_khz; ? }; +extern const u32 rti_wdt_fw[]; +extern const int rti_wdt_fw_size;FIT is the preferred way of packing images in U-Boot. Can you try using it?
How does that work? Some example for me?
Quoted 6 lines
Quoted 2 lines
If you happen to refer to fs-loader: That does not target OSPI, our primary use case.
No. I was thinking to pack the image in FIT along with ATF and OPTEE like in
k3_fit_atf.shand register aU_BOOT_FIT_LOADABLE_HANDLERfor installing the firmware.
In case of our board, that image is not processed by U-Boot (only generated). Also, processing it from the R5 loader would imply putting remoteproc support into that level, duplicating what we have in A53 U-Boot.
Quoted 10 lines
Quoted 4 lines
Quoted 4 lines
What benefit would that bring? There are other users of this pattern, e.g.
board/xilinx/zynqmp/pm_cfg_obj.S.I didn't know U-Boot is accepting this. Tom, is this the preferred way for including firmware images?
Quoted 2 lines
Quoted 1 line
Quoted 7 lines
Quoted 5 lines
The only benefit of an alternative loading mechanism seems to be handling of larger images from different sources. But that's what I would tackle via boot scripting and, thus, without this feature. If you only have a few hundred bytes to embed, like for k3-rti-wdt, you quickly have a lot of overhead with other approaches.
hmm.. Does the build break if firmware is not present?
Yes, if you configure to include the firmware but specify an invalid path, the build breaks.
Jan
Signature · 2 lines
Siemens AG, Corporate Technology, CT RDA IOT SES-DE Corporate Competence Center Embedded Linux
PATCH v2 2/3 watchdog: rti_wdt: Add support for loading firmware
Quoted 141 lines · Jan Kiszka
Quoted 113 lines · Lokesh Vutla
+Tom
Quoted 85 lines · Jan Kiszka
Quoted 84 lines · Jan Kiszka
Quoted 82 lines · Lokesh Vutla
Quoted 75 lines · Jan Kiszka
From: Jan Kiszka <[email protected]>
To avoid the need of extra boot scripting on AM65x for loading a watchdog firmware, add the required rproc init and loading logic for the first R5F core to the watchdog start handler. The firmware itself is embedded into U-Boot binary.
One possible firmware source is https://github.com/siemens/k3-rti-wdt.
Signed-off-by Jan Kiszka <[email protected]>---
?? drivers/watchdog/Kconfig????? | 20 ++++++++++++++++++++ ?? drivers/watchdog/Makefile???? |? 3 +++ ?? drivers/watchdog/rti_wdt.c??? | 24 ++++++++++++++++++++++++ ?? drivers/watchdog/rti_wdt_fw.S | 20 ++++++++++++++++++++?? 4 files changed, 67 insertions(+)
?? create mode 100644drivers/watchdog/rti_wdt_fw.Sdrivers/watchdog/Kconfig +0
-0@@ -162,6 +162,26 @@ config WDT_K3_RTI???????? Say Y here if you want to include support for the K3 watchdog ???????? timer (RTI module) available in the K3 generation of processors.
drivers/watchdog/Kconfig +20
-0+if WDT_K3_RTI + +config WDT_K3_RTI_LOAD_FW +??? bool "Load watchdog firmware" +??? depends on REMOTEPROC +??? help +????? Automatically load the specified firmware image into the MCU R5F +????? core 0. On the AM65x, this firmware is supposed to handle the expiry +????? of the watchdog timer, typically by resetting the system. + +config WDT_K3_RTI_FW_FILE +??? string "Watchdog firmware image file" +??? default "k3-rti-wdt.fw" +??? depends on WDT_K3_RTI_LOAD_FW +??? help +????? Firmware image to be embedded into U-Boot and loaded on watchdog +????? start. + +endif +?? config
WDT_SANDBOX
?????? bool "Enable Watchdog Timer support for Sandbox" ?????? depends on SANDBOX && WDTdrivers/watchdog/Makefile +0
-0@@ -28,7 +28,10 @@ obj-$(CONFIG_WDT_MT7621) += mt7621_wdt.o?? obj-$(CONFIG_WDT_MTK) += mtk_wdt.o
?? obj-$(CONFIG_WDT_OMAP3) += omap_wdt.o
?? obj-$(CONFIG_WDT_K3_RTI) += rti_wdt.o
+obj-$(CONFIG_WDT_K3_RTI_LOAD_FW) += rti_wdt_fw.o
?? obj-$(CONFIG_WDT_SP805) += sp805_wdt.o
?? obj-$(CONFIG_WDT_STM32MP) += stm32mp_wdt.o
?? obj-$(CONFIG_WDT_TANGIER) += tangier_wdt.o
?? obj-$(CONFIG_WDT_XILINX) += xilinx_wwdt.odrivers/watchdog/Makefile +2
-0+ +$(obj)/rti_wdt_fw.o: $(shell readlink -f $(CONFIG_WDT_K3_RTI_FW_FILE)) FORCEdrivers/watchdog/rti_wdt.c +0
-0@@ -14,6 +14,7 @@?? #include <
power-domain.h>
?? #include <wdt.h>
?? #include <asm/io.h>
+#include <remoteproc.h>
?? /* Timer register set definition */
?? #define RTIDWDCTRL???????0x90drivers/watchdog/rti_wdt.c +0
-0@@ -37,11 +38,16 @@Quoted 2 lines
?? #define
WDT_PRELOAD_MAX???????0xfff
+#defineRTI_PROC_ID??????? 0Can we get the rproc id from DT?
Quoted 6 lines
Quoted 2 lines
You mean, resolve "
mcu_r5fss0_core0" to the ID? Doable.I'm now probing for the first instance of "ti,am654-r5f" compatible. That excludes usage for the J721E for now, but that one is fine without firmware - provided there is way to prevent power-down for RTI watchdog otherwise...
I was more of thinking to have a DT property to reference R5-core. But anyways, the property is not present in kernel. I am okay with this for now.
Quoted 15 lines
Quoted 14 lines
Quoted 11 lines
drivers/watchdog/rti_wdt.c line 49
Quoted 9 lines
+
?? structrti_wdt_priv{
??????phys_addr_tregs;
?????? unsigned intclk_khz;
?? };drivers/watchdog/rti_wdt.c +2
-0+extern const u32 rti_wdt_fw[]; +extern const int rti_wdt_fw_size;FIT is the preferred way of packing images in U-Boot. Can you try using it?
How does that work? Some example for me?
Quoted 6 lines
Quoted 2 lines
If you happen to refer to fs-loader: That does not target OSPI, our primary use case.
No. I was thinking to pack the image in FIT along with ATF and OPTEE like in
k3_fit_atf.shand register aU_BOOT_FIT_LOADABLE_HANDLERfor installing the firmware.In case of our board, that image is not processed by U-Boot (only generated). Also, processing it from the R5 loader would imply putting remoteproc support into that level, duplicating what we have in A53 U-Boot.
Quoted 16 lines
Quoted 4 lines
Quoted 4 lines
What benefit would that bring? There are other users of this pattern, e.g.
board/xilinx/zynqmp/pm_cfg_obj.S.I didn't know U-Boot is accepting this. Tom, is this the preferred way for including firmware images?
Quoted 7 lines
Quoted 1 line
The only benefit of an alternative loading mechanism seems to be handling of larger images from different sources. But that's what I would tackle via boot scripting and, thus, without this feature. If you only have a few hundred bytes to embed, like for k3-rti-wdt, you quickly have a lot of overhead with other approaches.
Quoted 4 lines
Quoted 1 line
hmm.. Does the build break if firmware is not present?
Yes, if you configure to include the firmware but specify an invalid path, the build breaks.
So, how do we handle the travis CI/gitlab build without this firmware. I am not sure how xilinx is handling this. It should be the same case in the above scenario you pointed out.
Thanks and regards,
Lokesh
PATCH v2 2/3 watchdog: rti_wdt: Add support for loading firmware
Quoted 144 lines · Lokesh Vutla
Quoted 141 lines · Jan Kiszka
Quoted 113 lines · Lokesh Vutla
+Tom
Quoted 85 lines · Jan Kiszka
Quoted 84 lines · Jan Kiszka
Quoted 82 lines · Lokesh Vutla
Quoted 75 lines · Jan Kiszka
From: Jan Kiszka <[email protected]>
To avoid the need of extra boot scripting on AM65x for loading a watchdog firmware, add the required rproc init and loading logic for the first R5F core to the watchdog start handler. The firmware itself is embedded into U-Boot binary.
One possible firmware source is https://github.com/siemens/k3-rti-wdt.
Signed-off-by Jan Kiszka <[email protected]>--- ?? drivers/watchdog/Kconfig????? | 20 ++++++++++++++++++++ ?? drivers/watchdog/Makefile???? |? 3 +++ ?? drivers/watchdog/rti_wdt.c??? | 24 ++++++++++++++++++++++++ ?? drivers/watchdog/rti_wdt_fw.S | 20 ++++++++++++++++++++?? 4 files changed, 67 insertions(+)
?? create mode 100644drivers/watchdog/rti_wdt_fw.Sdrivers/watchdog/Kconfig +20
-0@@ -162,6 +162,26 @@ config WDT_K3_RTI ???????? Say Y here if you want to include support for the K3 watchdog ???????? timer (RTI module) available in the K3 generation of processors. +if WDT_K3_RTI + +config WDT_K3_RTI_LOAD_FW +??? bool "Load watchdog firmware" +??? depends on REMOTEPROC +??? help +????? Automatically load the specified firmware image into the MCU R5F +????? core 0. On the AM65x, this firmware is supposed to handle the expiry +????? of the watchdog timer, typically by resetting the system. + +config WDT_K3_RTI_FW_FILE +??? string "Watchdog firmware image file" +??? default "k3-rti-wdt.fw" +??? depends on WDT_K3_RTI_LOAD_FW +??? help +????? Firmware image to be embedded into U-Boot and loaded on watchdog +????? start. + +endif + ?? config WDT_SANDBOX ?????? bool "Enable Watchdog Timer support for Sandbox" ?????? depends on SANDBOX && WDTdrivers/watchdog/Makefile +3
-0@@ -28,7 +28,10 @@ obj-$(CONFIG_WDT_MT7621) += mt7621_wdt.o ?? obj-$(CONFIG_WDT_MTK) += mtk_wdt.o ?? obj-$(CONFIG_WDT_OMAP3) += omap_wdt.o ?? obj-$(CONFIG_WDT_K3_RTI) += rti_wdt.o +obj-$(CONFIG_WDT_K3_RTI_LOAD_FW) += rti_wdt_fw.o ?? obj-$(CONFIG_WDT_SP805) += sp805_wdt.o ?? obj-$(CONFIG_WDT_STM32MP) += stm32mp_wdt.o ?? obj-$(CONFIG_WDT_TANGIER) += tangier_wdt.o ?? obj-$(CONFIG_WDT_XILINX) += xilinx_wwdt.o + +$(obj)/rti_wdt_fw.o: $(shell readlink -f $(CONFIG_WDT_K3_RTI_FW_FILE)) FORCEdrivers/watchdog/rti_wdt.c +1
-0@@ -14,6 +14,7 @@ ?? #include <power-domain.h> ?? #include <wdt.h> ?? #include <asm/io.h> +#include <remoteproc.h> ?? /* Timer register set definition */ ?? #define RTIDWDCTRL??????? 0x90drivers/watchdog/rti_wdt.c line 39
Quoted 2 lines
drivers/watchdog/rti_wdt.c +1
-0@@ -37,11 +38,16 @@ ?? #define WDT_PRELOAD_MAX??????? 0xfff +#define RTI_PROC_ID ??????? 0Can we get the rproc id from DT?
Quoted 6 lines
Quoted 2 lines
You mean, resolve "
mcu_r5fss0_core0" to the ID? Doable.I'm now probing for the first instance of "ti,am654-r5f" compatible. That excludes usage for the J721E for now, but that one is fine without firmware - provided there is way to prevent power-down for RTI watchdog otherwise...
I was more of thinking to have a DT property to reference R5-core. But anyways, the property is not present in kernel. I am okay with this for now.
Quoted 15 lines
Quoted 14 lines
Quoted 11 lines
drivers/watchdog/rti_wdt.c line 46
Quoted 9 lines
drivers/watchdog/rti_wdt.c +3
-0+ ?? struct rti_wdt_priv { ?????? phys_addr_t regs; ?????? unsigned int clk_khz; ?? }; +extern const u32 rti_wdt_fw[]; +extern const int rti_wdt_fw_size;FIT is the preferred way of packing images in U-Boot. Can you try using it?
How does that work? Some example for me?
Quoted 6 lines
Quoted 2 lines
If you happen to refer to fs-loader: That does not target OSPI, our primary use case.
No. I was thinking to pack the image in FIT along with ATF and OPTEE like in
k3_fit_atf.shand register aU_BOOT_FIT_LOADABLE_HANDLERfor installing the firmware.In case of our board, that image is not processed by U-Boot (only generated). Also, processing it from the R5 loader would imply putting remoteproc support into that level, duplicating what we have in A53 U-Boot.
Quoted 16 lines
Quoted 4 lines
Quoted 4 lines
What benefit would that bring? There are other users of this pattern, e.g.
board/xilinx/zynqmp/pm_cfg_obj.S.I didn't know U-Boot is accepting this. Tom, is this the preferred way for including firmware images?
Quoted 7 lines
Quoted 1 line
The only benefit of an alternative loading mechanism seems to be handling of larger images from different sources. But that's what I would tackle via boot scripting and, thus, without this feature. If you only have a few hundred bytes to embed, like for k3-rti-wdt, you quickly have a lot of overhead with other approaches.
Quoted 8 lines
Quoted 4 lines
Quoted 1 line
hmm.. Does the build break if firmware is not present?
Yes, if you configure to include the firmware but specify an invalid path, the build breaks.
So, how do we handle the travis CI/gitlab build without this firmware. I am not sure how xilinx is handling this. It should be the same case in the above scenario you pointed out.
You mean some all-yes-config? We could create a dummy image prior to running that build.
The Xilinx has its logic disabled when the file name is empty, which is the default. The linker should kick unused bits out then. I can try that as well.
Jan
Signature · 2 lines
Siemens AG, Corporate Technology, CT RDA IOT SES-DE Corporate Competence Center Embedded Linux
PATCH v2 2/3 watchdog: rti_wdt: Add support for loading firmware
In reply to Lokesh VutlaQuoted 91 lines · Lokesh Vutla
+Tom
Quoted 88 lines · Jan Kiszka
Quoted 86 lines · Jan Kiszka
Quoted 74 lines · Lokesh Vutla
Quoted 71 lines · Jan Kiszka
From: Jan Kiszka <[email protected]>
To avoid the need of extra boot scripting on AM65x for loading a watchdog firmware, add the required rproc init and loading logic for the first R5F core to the watchdog start handler. The firmware itself is embedded into U-Boot binary.
One possible firmware source is https://github.com/siemens/k3-rti-wdt.
Signed-off-by Jan Kiszka <[email protected]>---
? drivers/watchdog/Kconfig????? | 20 ++++++++++++++++++++ ? drivers/watchdog/Makefile???? |? 3 +++ ? drivers/watchdog/rti_wdt.c??? | 24 ++++++++++++++++++++++++ ? drivers/watchdog/rti_wdt_fw.S | 20 ++++++++++++++++++++? 4 files changed, 67 insertions(+)
? create mode 100644drivers/watchdog/rti_wdt_fw.Sdrivers/watchdog/Kconfig +0
-0@@ -162,6 +162,26 @@ config WDT_K3_RTI??????? Say Y here if you want to include support for the K3 watchdog ??????? timer (RTI module) available in the K3 generation of processors.
drivers/watchdog/Kconfig +20
-0+if WDT_K3_RTI + +config WDT_K3_RTI_LOAD_FW +??? bool "Load watchdog firmware" +??? depends on REMOTEPROC +??? help +????? Automatically load the specified firmware image into the MCU R5F +????? core 0. On the AM65x, this firmware is supposed to handle the expiry +????? of the watchdog timer, typically by resetting the system. + +config WDT_K3_RTI_FW_FILE +??? string "Watchdog firmware image file" +??? default "k3-rti-wdt.fw" +??? depends on WDT_K3_RTI_LOAD_FW +??? help +????? Firmware image to be embedded into U-Boot and loaded on watchdog +????? start. + +endif +? config
WDT_SANDBOX
????? bool "Enable Watchdog Timer support for Sandbox" ????? depends on SANDBOX && WDTdrivers/watchdog/Makefile +0
-0@@ -28,7 +28,10 @@ obj-$(CONFIG_WDT_MT7621) += mt7621_wdt.o? obj-$(CONFIG_WDT_MTK) += mtk_wdt.o
? obj-$(CONFIG_WDT_OMAP3) += omap_wdt.o
? obj-$(CONFIG_WDT_K3_RTI) += rti_wdt.o
+obj-$(CONFIG_WDT_K3_RTI_LOAD_FW) += rti_wdt_fw.o
? obj-$(CONFIG_WDT_SP805) += sp805_wdt.o
? obj-$(CONFIG_WDT_STM32MP) += stm32mp_wdt.o
? obj-$(CONFIG_WDT_TANGIER) += tangier_wdt.o
? obj-$(CONFIG_WDT_XILINX) += xilinx_wwdt.odrivers/watchdog/Makefile +2
-0+ +$(obj)/rti_wdt_fw.o: $(shell readlink -f $(CONFIG_WDT_K3_RTI_FW_FILE)) FORCEdrivers/watchdog/rti_wdt.c +0
-0@@ -14,6 +14,7 @@? #include <
power-domain.h>
? #include <wdt.h>
? #include <asm/io.h>Quoted 8 lines
Quoted 6 lines
+#include <
remoteproc.h>
? /* Timer register set definition */
? #define RTIDWDCTRL???????0x90drivers/watchdog/rti_wdt.c +0
-0@@ -37,11 +38,16 @@? #define
WDT_PRELOAD_MAX???????0xfff
+#defineRTI_PROC_ID??????? 0Can we get the rproc id from DT?
You mean, resolve "
mcu_r5fss0_core0" to the ID? Doable.
Quoted 6 lines
Quoted 3 lines
I'm now probing for the first instance of "ti,am654-r5f" compatible. That excludes usage for the J721E for now, but that one is fine without firmware - provided there is way to prevent power-down for RTI watchdog otherwise...
I was more of thinking to have a DT property to reference R5-core. But anyways, the property is not present in kernel. I am okay with this for now.
Note that not all properties in a DT in Linux need to be used in Linux, this is something I _think_ there is growing understanding of.
Quoted 21 lines
Quoted 10 lines
Quoted 10 lines
Quoted 9 lines
drivers/watchdog/rti_wdt.c line 49
Quoted 7 lines
+
? structrti_wdt_priv{
?????phys_addr_tregs;
????? unsigned intclk_khz;
? };drivers/watchdog/rti_wdt.c +2
-0+extern const u32 rti_wdt_fw[]; +extern const int rti_wdt_fw_size;FIT is the preferred way of packing images in U-Boot. Can you try using it?
Quoted 5 lines
Quoted 2 lines
How does that work? Some example for me?
If you happen to refer to fs-loader: That does not target OSPI, our primary use case.
No. I was thinking to pack the image in FIT along with ATF and OPTEE like in
k3_fit_atf.shand register aU_BOOT_FIT_LOADABLE_HANDLERfor installing the firmware.Quoted 1 line
Quoted 5 lines
Quoted 2 lines
Quoted 2 lines
What benefit would that bring? There are other users of this pattern, e.g.
board/xilinx/zynqmp/pm_cfg_obj.S.I didn't know U-Boot is accepting this. Tom, is this the preferred way for including firmware images?
Adding in Michal. Why is this area doing what it's doing and not one of the other generic ways to handle this problem? Thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 659 bytes Desc: not available URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200629/ac5a7b82/attachment.sig>
PATCH v2 2/3 watchdog: rti_wdt: Add support for loading firmware
Quoted 123 lines · Tom Rini
Quoted 91 lines · Lokesh Vutla
+Tom
Quoted 88 lines · Jan Kiszka
Quoted 86 lines · Jan Kiszka
Quoted 74 lines · Lokesh Vutla
Quoted 71 lines · Jan Kiszka
From: Jan Kiszka <[email protected]>
To avoid the need of extra boot scripting on AM65x for loading a watchdog firmware, add the required rproc init and loading logic for the first R5F core to the watchdog start handler. The firmware itself is embedded into U-Boot binary.
One possible firmware source is https://github.com/siemens/k3-rti-wdt.
Signed-off-by Jan Kiszka <[email protected]>--- ? drivers/watchdog/Kconfig????? | 20 ++++++++++++++++++++ ? drivers/watchdog/Makefile???? |? 3 +++ ? drivers/watchdog/rti_wdt.c??? | 24 ++++++++++++++++++++++++ ? drivers/watchdog/rti_wdt_fw.S | 20 ++++++++++++++++++++? 4 files changed, 67 insertions(+)
? create mode 100644drivers/watchdog/rti_wdt_fw.Sdrivers/watchdog/Kconfig +20
-0@@ -162,6 +162,26 @@ config WDT_K3_RTI ??????? Say Y here if you want to include support for the K3 watchdog ??????? timer (RTI module) available in the K3 generation of processors. +if WDT_K3_RTI + +config WDT_K3_RTI_LOAD_FW +??? bool "Load watchdog firmware" +??? depends on REMOTEPROC +??? help +????? Automatically load the specified firmware image into the MCU R5F +????? core 0. On the AM65x, this firmware is supposed to handle the expiry +????? of the watchdog timer, typically by resetting the system. + +config WDT_K3_RTI_FW_FILE +??? string "Watchdog firmware image file" +??? default "k3-rti-wdt.fw" +??? depends on WDT_K3_RTI_LOAD_FW +??? help +????? Firmware image to be embedded into U-Boot and loaded on watchdog +????? start. + +endif + ? config WDT_SANDBOX ????? bool "Enable Watchdog Timer support for Sandbox" ????? depends on SANDBOX && WDTdrivers/watchdog/Makefile +3
-0@@ -28,7 +28,10 @@ obj-$(CONFIG_WDT_MT7621) += mt7621_wdt.o ? obj-$(CONFIG_WDT_MTK) += mtk_wdt.o ? obj-$(CONFIG_WDT_OMAP3) += omap_wdt.o ? obj-$(CONFIG_WDT_K3_RTI) += rti_wdt.o +obj-$(CONFIG_WDT_K3_RTI_LOAD_FW) += rti_wdt_fw.o ? obj-$(CONFIG_WDT_SP805) += sp805_wdt.o ? obj-$(CONFIG_WDT_STM32MP) += stm32mp_wdt.o ? obj-$(CONFIG_WDT_TANGIER) += tangier_wdt.o ? obj-$(CONFIG_WDT_XILINX) += xilinx_wwdt.o + +$(obj)/rti_wdt_fw.o: $(shell readlink -f $(CONFIG_WDT_K3_RTI_FW_FILE)) FORCEdrivers/watchdog/rti_wdt.c +0
-0@@ -14,6 +14,7 @@ ? #include <power-domain.h> ? #include <wdt.h> ? #include <asm/io.h>Quoted 8 lines
drivers/watchdog/rti_wdt.c line 39
Quoted 6 lines
drivers/watchdog/rti_wdt.c +2
-0+#include <remoteproc.h> ? /* Timer register set definition */ ? #define RTIDWDCTRL??????? 0x90@@ -37,11 +38,16 @@ ? #define WDT_PRELOAD_MAX??????? 0xfff +#define RTI_PROC_ID ??????? 0Can we get the rproc id from DT?
You mean, resolve "
mcu_r5fss0_core0" to the ID? Doable.Quoted 6 lines
Quoted 3 lines
I'm now probing for the first instance of "ti,am654-r5f" compatible. That excludes usage for the J721E for now, but that one is fine without firmware - provided there is way to prevent power-down for RTI watchdog otherwise...
I was more of thinking to have a DT property to reference R5-core. But anyways, the property is not present in kernel. I am okay with this for now.
Note that not all properties in a DT in Linux need to be used in Linux, this is something I _think_ there is growing understanding of.
Quoted 21 lines
Quoted 10 lines
Quoted 10 lines
Quoted 9 lines
drivers/watchdog/rti_wdt.c line 46
Quoted 7 lines
drivers/watchdog/rti_wdt.c +3
-0+ ? struct rti_wdt_priv { ????? phys_addr_t regs; ????? unsigned int clk_khz; ? }; +extern const u32 rti_wdt_fw[]; +extern const int rti_wdt_fw_size;FIT is the preferred way of packing images in U-Boot. Can you try using it?
Quoted 5 lines
Quoted 2 lines
How does that work? Some example for me?
If you happen to refer to fs-loader: That does not target OSPI, our primary use case.
No. I was thinking to pack the image in FIT along with ATF and OPTEE like in
k3_fit_atf.shand register aU_BOOT_FIT_LOADABLE_HANDLERfor installing the firmware.Quoted 1 line
Quoted 9 lines
Quoted 5 lines
Quoted 2 lines
Quoted 2 lines
What benefit would that bring? There are other users of this pattern, e.g.
board/xilinx/zynqmp/pm_cfg_obj.S.I didn't know U-Boot is accepting this. Tom, is this the preferred way for including firmware images?
Adding in Michal. Why is this area doing what it's doing and not one of the other generic ways to handle this problem? Thanks!
So, what are the recommended "generic ways" for these use cases?
Is there a way to stick own stuff into u-boot.itb and get that provided to some handler of U-Boot proper? Seems unlikely. The pattern I found pushes the firmware into the kernel fit image - which is a clear no-go for the watchdog use case because it shall monitor the booting of that very same image (software update case).
Jan
Signature · 2 lines
Siemens AG, Corporate Technology, CT RDA IOT SES-DE Corporate Competence Center Embedded Linux
PATCH v2 2/3 watchdog: rti_wdt: Add support for loading firmware
Quoted 154 lines · Jan Kiszka
Quoted 143 lines · Tom Rini
Quoted 106 lines · Lokesh Vutla
+Tom
Quoted 96 lines · Jan Kiszka
Quoted 92 lines · Jan Kiszka
Quoted 82 lines · Lokesh Vutla
Quoted 79 lines · Jan Kiszka
From: Jan Kiszka <[email protected]>
To avoid the need of extra boot scripting on AM65x for loading a watchdog firmware, add the required rproc init and loading logic for the
first R5F core to the watchdog start handler. The firmware itself is embedded into U-Boot binary.One possible firmware source is
https://github.com/siemens/k3-rti-wdt.Signed-off-by Jan Kiszka <[email protected]>---
?? drivers/watchdog/Kconfig????? | 20 ++++++++++++++++++++ ?? drivers/watchdog/Makefile???? |? 3 +++ ?? drivers/watchdog/rti_wdt.c??? | 24 ++++++++++++++++++++++++ ?? drivers/watchdog/rti_wdt_fw.S | 20 ++++++++++++++++++++?? 4 files changed, 67 insertions(+)
?? create mode 100644drivers/watchdog/rti_wdt_fw.Sdrivers/watchdog/Kconfig +0
-0@@ -162,6 +162,26 @@ config WDT_K3_RTI???????? Say Y here if you want to include support for the K3 watchdog
???????? timer (RTI module) available in the K3 generation of processors.drivers/watchdog/Kconfig +7
-0+if WDT_K3_RTI + +config WDT_K3_RTI_LOAD_FW +??? bool "Load watchdog firmware" +??? depends on REMOTEPROC +??? help +????? Automatically load the specified firmware image into theMCU R5F
+????? core 0. On the AM65x, this firmware is supposed to handle the expiry
+????? of the watchdog timer, typically by resetting the system.drivers/watchdog/Kconfig +7
-0+ +config WDT_K3_RTI_FW_FILE +??? string "Watchdog firmware image file" +??? default "k3-rti-wdt.fw" +??? depends on WDT_K3_RTI_LOAD_FW +??? help +????? Firmware image to be embedded into U-Boot and loaded onwatchdog
+????? start.drivers/watchdog/Kconfig +3
-0+ +endif +?? config
WDT_SANDBOX
?????? bool "Enable Watchdog Timer support for Sandbox" ?????? depends on SANDBOX && WDTdrivers/watchdog/Makefile +0
-0@@ -28,7 +28,10 @@ obj-$(CONFIG_WDT_MT7621) += mt7621_wdt.o?? obj-$(CONFIG_WDT_MTK) += mtk_wdt.o
?? obj-$(CONFIG_WDT_OMAP3) += omap_wdt.o
?? obj-$(CONFIG_WDT_K3_RTI) += rti_wdt.o
+obj-$(CONFIG_WDT_K3_RTI_LOAD_FW) += rti_wdt_fw.o
?? obj-$(CONFIG_WDT_SP805) += sp805_wdt.o
?? obj-$(CONFIG_WDT_STM32MP) += stm32mp_wdt.o
?? obj-$(CONFIG_WDT_TANGIER) += tangier_wdt.o
?? obj-$(CONFIG_WDT_XILINX) += xilinx_wwdt.o
+
+$(obj)/rti_wdt_fw.o: $(shell readlink -f
$(CONFIG_WDT_K3_RTI_FW_FILE)) FORCEdrivers/watchdog/rti_wdt.c +0
-0@@ -14,6 +14,7 @@?? #include <
power-domain.h>
?? #include <wdt.h>
?? #include <asm/io.h>Quoted 8 lines
Quoted 6 lines
+#include <
remoteproc.h>
?? /* Timer register set definition */
?? #define RTIDWDCTRL???????0x90drivers/watchdog/rti_wdt.c +0
-0@@ -37,11 +38,16 @@?? #define
WDT_PRELOAD_MAX???????0xfff
+#defineRTI_PROC_ID??????? 0Can we get the rproc id from DT?
Quoted 2 lines
You mean, resolve "
mcu_r5fss0_core0" to the ID? Doable.Quoted 6 lines
I'm now probing for the first instance of "ti,am654-r5f" compatible. That
excludes usage for the J721E for now, but that one is fine without firmware -
provided there is way to prevent power-down for RTI watchdog otherwise...Quoted 3 lines
I was more of thinking to have a DT property to reference R5-core. But anyways,
the property is not present in kernel. I am okay with this for now.Note that not all properties in a DT in Linux need to be used in Linux, this is something I _think_ there is growing understanding of.
Quoted 29 lines
Quoted 11 lines
Quoted 11 lines
Quoted 10 lines
drivers/watchdog/rti_wdt.c
Quoted 7 lines
+
?? structrti_wdt_priv{
??????phys_addr_tregs;
?????? unsigned intclk_khz;
?? };drivers/watchdog/rti_wdt.c +2
-0+extern const u32 rti_wdt_fw[]; +extern const int rti_wdt_fw_size;FIT is the preferred way of packing images in U-Boot. Can you try using it?
Quoted 6 lines
Quoted 2 lines
How does that work? Some example for me?
If you happen to refer to fs-loader: That does not target OSPI, our primary use
case.No. I was thinking to pack the image in FIT along with ATF and OPTEE like in
k3_fit_atf.shand register aU_BOOT_FIT_LOADABLE_HANDLERfor installing the
firmware.Quoted 4 lines
Quoted 4 lines
What benefit would that bring? There are other users of this pattern, e.g.
board/xilinx/zynqmp/pm_cfg_obj.S.Quoted 7 lines
Quoted 3 lines
I didn't know U-Boot is accepting this. Tom, is this the preferred way for
including firmware images?Adding in Michal.? Why is this area doing what it's doing and not one of the other generic ways to handle this problem?? Thanks!
So, what are the recommended "generic ways" for these use cases?
Quoted 8 lines
Is there a way to stick own stuff into u-boot.itb and get that provided to some handler of U-Boot proper? Seems unlikely. The pattern I found pushes the firmware into the kernel fit image - which is a clear no-go for the watchdog use case because it shall monitor the booting of that very same image (software update case).
Jan
Ping on this. I'd like to move forward with this series.
Jan
Signature · 2 lines
Siemens AG, Corporate Technology, CT RDA IOT SES-DE Corporate Competence Center Embedded Linux
PATCH v2 2/3 watchdog: rti_wdt: Add support for loading firmware
Hi Jan,
Quoted 145 lines · Jan Kiszka
Quoted 144 lines · Jan Kiszka
Quoted 125 lines · Tom Rini
Quoted 92 lines · Lokesh Vutla
+Tom
Quoted 89 lines · Jan Kiszka
Quoted 87 lines · Jan Kiszka
Quoted 75 lines · Lokesh Vutla
Quoted 72 lines · Jan Kiszka
From: Jan Kiszka <[email protected]>
To avoid the need of extra boot scripting on AM65x for loading a watchdog firmware, add the required rproc init and loading logic for the first R5F core to the watchdog start handler. The firmware itself is embedded into U-Boot binary.
One possible firmware source is https://github.com/siemens/k3-rti-wdt.
Signed-off-by Jan Kiszka <[email protected]>---
?? drivers/watchdog/Kconfig????? | 20 ++++++++++++++++++++ ?? drivers/watchdog/Makefile???? |? 3 +++ ?? drivers/watchdog/rti_wdt.c??? | 24 ++++++++++++++++++++++++ ?? drivers/watchdog/rti_wdt_fw.S | 20 ++++++++++++++++++++?? 4 files changed, 67 insertions(+)
?? create mode 100644drivers/watchdog/rti_wdt_fw.Sdrivers/watchdog/Kconfig +0
-0@@ -162,6 +162,26 @@ config WDT_K3_RTI???????? Say Y here if you want to include support for the K3 watchdog ???????? timer (RTI module) available in the K3 generation of processors.
drivers/watchdog/Kconfig +20
-0+if WDT_K3_RTI + +config WDT_K3_RTI_LOAD_FW +??? bool "Load watchdog firmware" +??? depends on REMOTEPROC +??? help +????? Automatically load the specified firmware image into the MCU R5F +????? core 0. On the AM65x, this firmware is supposed to handle the expiry +????? of the watchdog timer, typically by resetting the system. + +config WDT_K3_RTI_FW_FILE +??? string "Watchdog firmware image file" +??? default "k3-rti-wdt.fw" +??? depends on WDT_K3_RTI_LOAD_FW +??? help +????? Firmware image to be embedded into U-Boot and loaded on watchdog +????? start. + +endif +?? config
WDT_SANDBOX
?????? bool "Enable Watchdog Timer support for Sandbox" ?????? depends on SANDBOX && WDTdrivers/watchdog/Makefile +0
-0@@ -28,7 +28,10 @@ obj-$(CONFIG_WDT_MT7621) += mt7621_wdt.o?? obj-$(CONFIG_WDT_MTK) += mtk_wdt.o
?? obj-$(CONFIG_WDT_OMAP3) += omap_wdt.o
?? obj-$(CONFIG_WDT_K3_RTI) += rti_wdt.o +obj-$(CONFIG_WDT_K3_RTI_LOAD_FW) += rti_wdt_fw.o
?? obj-$(CONFIG_WDT_SP805) += sp805_wdt.o
?? obj-$(CONFIG_WDT_STM32MP) += stm32mp_wdt.o
?? obj-$(CONFIG_WDT_TANGIER) += tangier_wdt.o
?? obj-$(CONFIG_WDT_XILINX) += xilinx_wwdt.o
+
+$(obj)/rti_wdt_fw.o: $(shell readlink -f $(CONFIG_WDT_K3_RTI_FW_FILE)) FORCEdrivers/watchdog/rti_wdt.c +0
-0@@ -14,6 +14,7 @@?? #include <
power-domain.h>
?? #include <wdt.h>
?? #include <asm/io.h>Quoted 8 lines
Quoted 6 lines
+#include <
remoteproc.h>
?? /* Timer register set definition */
?? #define RTIDWDCTRL???????0x90drivers/watchdog/rti_wdt.c +0
-0@@ -37,11 +38,16 @@?? #define
WDT_PRELOAD_MAX???????0xfff
+#defineRTI_PROC_ID??????? 0Can we get the rproc id from DT?
You mean, resolve "
mcu_r5fss0_core0" to the ID? Doable.Quoted 6 lines
Quoted 3 lines
I'm now probing for the first instance of "ti,am654-r5f" compatible. That excludes usage for the J721E for now, but that one is fine without firmware - provided there is way to prevent power-down for RTI watchdog otherwise...
I was more of thinking to have a DT property to reference R5-core. But anyways, the property is not present in kernel. I am okay with this for now.
Note that not all properties in a DT in Linux need to be used in Linux, this is something I _think_ there is growing understanding of.
Quoted 22 lines
Quoted 10 lines
Quoted 10 lines
Quoted 9 lines
drivers/watchdog/rti_wdt.c
Quoted 7 lines
+
?? structrti_wdt_priv{
??????phys_addr_tregs;
?????? unsigned intclk_khz;
?? };drivers/watchdog/rti_wdt.c +2
-0+extern const u32 rti_wdt_fw[]; +extern const int rti_wdt_fw_size;FIT is the preferred way of packing images in U-Boot. Can you try using it?
Quoted 6 lines
Quoted 2 lines
How does that work? Some example for me?
If you happen to refer to fs-loader: That does not target OSPI, our primary use
case.No. I was thinking to pack the image in FIT along with ATF and OPTEE like in
k3_fit_atf.shand register aU_BOOT_FIT_LOADABLE_HANDLERfor installing the firmware.Quoted 1 line
Quoted 9 lines
Quoted 5 lines
Quoted 2 lines
Quoted 2 lines
What benefit would that bring? There are other users of this pattern, e.g.
board/xilinx/zynqmp/pm_cfg_obj.S.I didn't know U-Boot is accepting this. Tom, is this the preferred way for including firmware images?
Adding in Michal.? Why is this area doing what it's doing and not one of the other generic ways to handle this problem?? Thanks!
So, what are the recommended "generic ways" for these use cases?
Is there a way to stick own stuff into u-boot.itb and get that provided to some handler of U-Boot proper? Seems unlikely. The pattern I found pushes the firmware into the kernel fit image - which is a clear no-go for the watchdog use case because it shall monitor the booting of that very same image (software update case).
Quoted 4 lines
Quoted 2 lines
Jan
Ping on this. I'd like to move forward with this series.
If you want remotecore to be loaded early, then my preference would be to pack Firmware inside FIT image(along with A72 SPL, ATF or A72 U-Boot) as loadable and register a handle to load and start the rproc in SPL. If it can be delayed, I prefer to do at U-Boot prompt.
However, the driver can be merged separately. If you can re post the driver part I can pull it in soon.
Thanks and regards,
Lokesh
PATCH v2 2/3 watchdog: rti_wdt: Add support for loading firmware
Quoted 151 lines · Lokesh Vutla
Hi Jan,
Quoted 148 lines · Jan Kiszka
Quoted 146 lines · Jan Kiszka
Quoted 125 lines · Tom Rini
Quoted 92 lines · Lokesh Vutla
+Tom
Quoted 89 lines · Jan Kiszka
Quoted 87 lines · Jan Kiszka
Quoted 75 lines · Lokesh Vutla
Quoted 72 lines · Jan Kiszka
From: Jan Kiszka <[email protected]>
To avoid the need of extra boot scripting on AM65x for loading a watchdog firmware, add the required rproc init and loading logic for the first R5F core to the watchdog start handler. The firmware itself is embedded into U-Boot binary.
One possible firmware source is https://github.com/siemens/k3-rti-wdt.
Signed-off-by Jan Kiszka <[email protected]>--- ?? drivers/watchdog/Kconfig????? | 20 ++++++++++++++++++++ ?? drivers/watchdog/Makefile???? |? 3 +++ ?? drivers/watchdog/rti_wdt.c??? | 24 ++++++++++++++++++++++++ ?? drivers/watchdog/rti_wdt_fw.S | 20 ++++++++++++++++++++?? 4 files changed, 67 insertions(+)
?? create mode 100644drivers/watchdog/rti_wdt_fw.Sdrivers/watchdog/Kconfig +20
-0@@ -162,6 +162,26 @@ config WDT_K3_RTI ???????? Say Y here if you want to include support for the K3 watchdog ???????? timer (RTI module) available in the K3 generation of processors. +if WDT_K3_RTI + +config WDT_K3_RTI_LOAD_FW +??? bool "Load watchdog firmware" +??? depends on REMOTEPROC +??? help +????? Automatically load the specified firmware image into the MCU R5F +????? core 0. On the AM65x, this firmware is supposed to handle the expiry +????? of the watchdog timer, typically by resetting the system. + +config WDT_K3_RTI_FW_FILE +??? string "Watchdog firmware image file" +??? default "k3-rti-wdt.fw" +??? depends on WDT_K3_RTI_LOAD_FW +??? help +????? Firmware image to be embedded into U-Boot and loaded on watchdog +????? start. + +endif + ?? config WDT_SANDBOX ?????? bool "Enable Watchdog Timer support for Sandbox" ?????? depends on SANDBOX && WDTdrivers/watchdog/Makefile +3
-0@@ -28,7 +28,10 @@ obj-$(CONFIG_WDT_MT7621) += mt7621_wdt.o ?? obj-$(CONFIG_WDT_MTK) += mtk_wdt.o ?? obj-$(CONFIG_WDT_OMAP3) += omap_wdt.o ?? obj-$(CONFIG_WDT_K3_RTI) += rti_wdt.o +obj-$(CONFIG_WDT_K3_RTI_LOAD_FW) += rti_wdt_fw.o ?? obj-$(CONFIG_WDT_SP805) += sp805_wdt.o ?? obj-$(CONFIG_WDT_STM32MP) += stm32mp_wdt.o ?? obj-$(CONFIG_WDT_TANGIER) += tangier_wdt.o ?? obj-$(CONFIG_WDT_XILINX) += xilinx_wwdt.o + +$(obj)/rti_wdt_fw.o: $(shell readlink -f $(CONFIG_WDT_K3_RTI_FW_FILE))FORCE
drivers/watchdog/rti_wdt.c +0
-0@@ -14,6 +14,7 @@ ?? #include <power-domain.h> ?? #include <wdt.h> ?? #include <asm/io.h>Quoted 8 lines
drivers/watchdog/rti_wdt.c line 39
Quoted 6 lines
drivers/watchdog/rti_wdt.c +2
-0+#include <remoteproc.h> ?? /* Timer register set definition */ ?? #define RTIDWDCTRL??????? 0x90@@ -37,11 +38,16 @@ ?? #define WDT_PRELOAD_MAX??????? 0xfff +#define RTI_PROC_ID ??????? 0Can we get the rproc id from DT?
You mean, resolve "
mcu_r5fss0_core0" to the ID? Doable.Quoted 6 lines
Quoted 3 lines
I'm now probing for the first instance of "ti,am654-r5f" compatible. That excludes usage for the J721E for now, but that one is fine without firmware - provided there is way to prevent power-down for RTI watchdog otherwise...
I was more of thinking to have a DT property to reference R5-core. But anyways, the property is not present in kernel. I am okay with this for now.
Note that not all properties in a DT in Linux need to be used in Linux, this is something I _think_ there is growing understanding of.
Quoted 22 lines
Quoted 10 lines
Quoted 10 lines
Quoted 9 lines
drivers/watchdog/rti_wdt.c line 46
Quoted 7 lines
drivers/watchdog/rti_wdt.c +3
-0+ ?? struct rti_wdt_priv { ?????? phys_addr_t regs; ?????? unsigned int clk_khz; ?? }; +extern const u32 rti_wdt_fw[]; +extern const int rti_wdt_fw_size;FIT is the preferred way of packing images in U-Boot. Can you try using it?
Quoted 6 lines
Quoted 2 lines
How does that work? Some example for me?
If you happen to refer to fs-loader: That does not target OSPI, our primary use
case.No. I was thinking to pack the image in FIT along with ATF and OPTEE like in
k3_fit_atf.shand register aU_BOOT_FIT_LOADABLE_HANDLERfor installing the firmware.Quoted 1 line
Quoted 9 lines
Quoted 5 lines
Quoted 2 lines
Quoted 2 lines
What benefit would that bring? There are other users of this pattern, e.g.
board/xilinx/zynqmp/pm_cfg_obj.S.I didn't know U-Boot is accepting this. Tom, is this the preferred way for including firmware images?
Adding in Michal.? Why is this area doing what it's doing and not one of the other generic ways to handle this problem?? Thanks!
So, what are the recommended "generic ways" for these use cases?
Is there a way to stick own stuff into u-boot.itb and get that provided to some handler of U-Boot proper? Seems unlikely. The pattern I found pushes the firmware into the kernel fit image - which is a clear no-go for the watchdog use case because it shall monitor the booting of that very same image (software update case).
Jan
Quoted 7 lines
Quoted 1 line
Ping on this. I'd like to move forward with this series.
If you want remotecore to be loaded early, then my preference would be to pack Firmware inside FIT
image(along with A72 SPL, ATF or A72 U-Boot)as loadable and register a handle to load and start the rproc in SPL. If it can be delayed, I prefer to do at U-Boot prompt.
So far, we do not need it in SPL as we have no procedure to update U-Boot proper safely. Moving things to SPL would imply carrying the remoteproc infrastructure twice.
For loading from the prompt, we are still lacking a handy way to bundle the firmware with the integrity-checked U-Boot proper. Yes, technically I could push those 676 bytes into a fitimage, sign it, reserve a block in SPI flash or some other storage, load it from there and validate it. But that's overkill IMHO.
Quoted 3 lines
However, the driver can be merged separately. If you can re post the driver part I can pull it in soon.
You could cherry-pick patch 1 and 3 for that already, they still apply.
Thanks,
Jan
Signature · 2 lines
Siemens AG, Corporate Technology, CT RDA IOT SES-DE Corporate Competence Center Embedded Linux
PATCH v2 3/3 arm: dts: k3: Add RTI watchdogs
In reply to Jan KiszkaFrom: Jan Kiszka <[email protected]>
Add DT entries for main domain watchdog0 and 1 instances on the J721e well as RTI1-based watchdog on the AM65x. RTI0 does not work for this purpose on the AM65x, so leave it out.
On AM65x, we mark the power-domain as shared because RTI firmware such as https://github.com/siemens/k3-rti-wdt may request it as well in order to prevent accidental shutdown of the watchdog.
--- arch/arm/dts/k3-am65-mcu.dtsi | 9 +++++++++ arch/arm/dts/k3-j721e-main.dtsi | 18 ++++++++++++++++++ 2 files changed, 27 insertions(+)
arch/arm/dts/k3-am65-mcu.dtsi +9 -0
@@ -102,4 +102,13 @@ #size-cells = <0>; }; }; + + mcu_rti1: rti at 40610000 { + compatible = "ti,j7-rti-wdt"; + reg = <0x0 0x40610000 0x0 0x100>; + clocks = <&k3_clks 135 0>; + power-domains = <&k3_pds 135 TI_SCI_PD_SHARED>; + assigned-clocks = <&k3_clks 135 0>; + assigned-clock-parents = <&k3_clks 135 4>; + }; };
arch/arm/dts/k3-j721e-main.dtsi +18 -0
@@ -543,4 +543,22 @@ clocks = <&k3_clks 193 0>; power-domains = <&k3_pds 193 TI_SCI_PD_EXCLUSIVE>; }; + + watchdog0: watchdog at 2200000 { + compatible = "ti,j7-rti-wdt"; + reg = <0x0 0x2200000 0x0 0x100>; + clocks = <&k3_clks 252 1>; + power-domains = <&k3_pds 252 TI_SCI_PD_EXCLUSIVE>; + assigned-clocks = <&k3_clks 252 1>; + assigned-clock-parents = <&k3_clks 252 5>; + }; + + watchdog1: watchdog at 2210000 { + compatible = "ti,j7-rti-wdt"; + reg = <0x0 0x2210000 0x0 0x100>; + clocks = <&k3_clks 253 1>; + power-domains = <&k3_pds 253 TI_SCI_PD_EXCLUSIVE>; + assigned-clocks = <&k3_clks 253 1>; + assigned-clock-parents = <&k3_clks 253 5>; + }; };
Signature · 1 line
2.26.2
v2 cover watchdog: K3: Add RTI watchdog support
In reply to Jan KiszkaQuoted 10 lines · Jan Kiszka
This brings watchdog support for the TI K3 SoCs, derived from the Linux kernel, augmented with firmware loading as needed on the AM65x.
Tested on the AM65x EVM and the IOT2050 (also AM65x-based, upstream support will be posted soon).
Changes in v2:
- keep watchdog powered when handing over to Linux
- drop unneeded explicit power-on
- account for RTI firmware locking the power domain
Patch 1 and 3 merged applied.
Thanks and regards,
Lokesh
v2 cover watchdog: K3: Add RTI watchdog support
Quoted 9 lines · Lokesh Vutla
Quoted 6 lines · Jan Kiszka
This brings watchdog support for the TI K3 SoCs, derived from the Linux kernel, augmented with firmware loading as needed on the AM65x.
Tested on the AM65x EVM and the IOT2050 (also AM65x-based, upstream support will be posted soon).
Quoted 7 lines
Quoted 4 lines
Changes in v2:
- keep watchdog powered when handing over to Linux
- drop unneeded explicit power-on
- account for RTI firmware locking the power domainPatch 1 and 3 merged applied.
Thanks. Still taking workable suggestions for loading the firmware.
Jan
Signature · 2 lines
Siemens AG, Corporate Technology, CT RDA IOT SES-DE Corporate Competence Center Embedded Linux
v2 cover watchdog: K3: Add RTI watchdog support
Quoted 15 lines · Jan Kiszka
Quoted 14 lines · Lokesh Vutla
Quoted 10 lines · Jan Kiszka
This brings watchdog support for the TI K3 SoCs, derived from the Linux kernel, augmented with firmware loading as needed on the AM65x.
Tested on the AM65x EVM and the IOT2050 (also AM65x-based, upstream support will be posted soon).
Changes in v2:
? - keep watchdog powered when handing over to Linux ? - drop unneeded explicit power-on
? - account for RTI firmware locking the power domain
Quoted 4 lines
Quoted 2 lines
Patch 1 and 3 merged applied.
Thanks. Still taking workable suggestions for loading the firmware.
FIT image is the one that I can think off. Since SPL is loading the FIT image, SPL_HANDOFF can be used to pass on the loadaddr from SPL to U-Boot and U-Boot can start the remote cores using this info.
Thanks and regards,
Lokesh
v2 cover watchdog: K3: Add RTI watchdog support
Quoted 18 lines · Lokesh Vutla
Quoted 15 lines · Jan Kiszka
Quoted 14 lines · Lokesh Vutla
Quoted 10 lines · Jan Kiszka
This brings watchdog support for the TI K3 SoCs, derived from the Linux kernel, augmented with firmware loading as needed on the AM65x.
Tested on the AM65x EVM and the IOT2050 (also AM65x-based, upstream support will be posted soon).
Changes in v2:
? - keep watchdog powered when handing over to Linux ? - drop unneeded explicit power-on
? - account for RTI firmware locking the power domain
Quoted 8 lines
Quoted 4 lines
Quoted 2 lines
Patch 1 and 3 merged applied.
Thanks. Still taking workable suggestions for loading the firmware.
FIT image is the one that I can think off. Since SPL is loading the FIT image,
SPL_HANDOFFcan be used to pass on the loadaddr from SPL to U-Boot and U-Boot can start the remote cores using this info.
OK, just the ensure I got the idea correctly:
- extend struct spl_handoff or arch_spl_handoff with the fit image loadaddr that spl is processing
- stick the watchdog firmware into the u-boot proper fit image (generated by tools/k3_fit_atf.sh or shipped via the board folder, as in our case)
- from the watchdog driver, trigger parsing of that fit image and extracting of the firmware from there
Jan
Signature · 2 lines
Siemens AG, Corporate Technology, CT RDA IOT SES-DE Corporate Competence Center Embedded Linux
v2 cover watchdog: K3: Add RTI watchdog support
Hi Jan,
Quoted 24 lines · Jan Kiszka
Quoted 23 lines · Lokesh Vutla
Quoted 19 lines · Jan Kiszka
Quoted 9 lines · Lokesh Vutla
Quoted 6 lines · Jan Kiszka
This brings watchdog support for the TI K3 SoCs, derived from the Linux kernel, augmented with firmware loading as needed on the AM65x.
Tested on the AM65x EVM and the IOT2050 (also AM65x-based, upstream support will be posted soon).
Quoted 7 lines
Quoted 4 lines
Changes in v2:
?? - keep watchdog powered when handing over to Linux ?? - drop unneeded explicit power-on
?? - account for RTI firmware locking the power domainPatch 1 and 3 merged applied.
Thanks. Still taking workable suggestions for loading the firmware.
Quoted 8 lines
Quoted 3 lines
FIT image is the one that I can think off. Since SPL is loading the FIT image,
SPL_HANDOFFcan be used to pass on the loadaddr from SPL to U-Boot and U-Boot can start the remote cores using this info.OK, just the ensure I got the idea correctly:
?- extend struct
spl_handofforarch_spl_handoffwith the fit image ?? loadaddr that spl is processing
Yes
Quoted 4 lines
?- stick the watchdog firmware into the u-boot proper fit image ?? (generated by
tools/k3_fit_atf.shor shipped via the board folder, as ?? in our case)
IMHO, not via board folder. k3_fit_atf is used to generate a53 spl images. May be create a new one that packs fit image with u-boot and firmware. Or can you check if binman in u-boot works for you?
Quoted 3 lines
?- from the watchdog driver, trigger parsing of that fit image and ?? extracting of the firmware from there
Yes
Thanks and regards,
Lokesh
Quoted 3 lines
Jan
v2 cover watchdog: K3: Add RTI watchdog support
Quoted 36 lines · Lokesh Vutla
Hi Jan,
Quoted 24 lines · Jan Kiszka
Quoted 23 lines · Lokesh Vutla
Quoted 19 lines · Jan Kiszka
Quoted 9 lines · Lokesh Vutla
Quoted 6 lines · Jan Kiszka
This brings watchdog support for the TI K3 SoCs, derived from the Linux kernel, augmented with firmware loading as needed on the AM65x.
Tested on the AM65x EVM and the IOT2050 (also AM65x-based, upstream support will be posted soon).
Quoted 7 lines
Quoted 4 lines
Changes in v2:
?? - keep watchdog powered when handing over to Linux ?? - drop unneeded explicit power-on
?? - account for RTI firmware locking the power domainPatch 1 and 3 merged applied.
Thanks. Still taking workable suggestions for loading the firmware.
Quoted 8 lines
Quoted 3 lines
FIT image is the one that I can think off. Since SPL is loading the FIT image,
SPL_HANDOFFcan be used to pass on the loadaddr from SPL to U-Boot and U-Boot can start the remote cores using this info.OK, just the ensure I got the idea correctly:
?- extend struct
spl_handofforarch_spl_handoffwith the fit image ?? loadaddr that spl is processing
Quoted 8 lines
Yes
Quoted 4 lines
?- stick the watchdog firmware into the u-boot proper fit image ?? (generated by
tools/k3_fit_atf.shor shipped via the board folder, as ?? in our case)IMHO, not via board folder.
k3_fit_atfis used to generate a53 spl images. May
Yeah, right. We also have a fit image for u-boot proper, that confused me.
Quoted 2 lines
be create a new one that packs fit image with u-boot and firmware. Or can you check if binman in u-boot works for you?
You mean, pack the u-boot proper with the firmware? Then we could stick the result in an signed fit image when needed. And I could read the offset of the firmware from the generated dtb - provided binman can deal with multiple configurations like we have.
Jan
Signature · 2 lines
Siemens AG, Corporate Technology, CT RDA IOT SES-DE Corporate Competence Center Embedded Linux
v2 cover watchdog: K3: Add RTI watchdog support
Quoted 48 lines · Jan Kiszka
Quoted 36 lines · Lokesh Vutla
Hi Jan,
Quoted 24 lines · Jan Kiszka
Quoted 23 lines · Lokesh Vutla
Quoted 19 lines · Jan Kiszka
Quoted 9 lines · Lokesh Vutla
Quoted 6 lines · Jan Kiszka
This brings watchdog support for the TI K3 SoCs, derived from the Linux kernel, augmented with firmware loading as needed on the AM65x.
Tested on the AM65x EVM and the IOT2050 (also AM65x-based, upstream support will be posted soon).
Quoted 7 lines
Quoted 4 lines
Changes in v2:
??? - keep watchdog powered when handing over to Linux ??? - drop unneeded explicit power-on
??? - account for RTI firmware locking the power domainPatch 1 and 3 merged applied.
Thanks. Still taking workable suggestions for loading the firmware.
Quoted 8 lines
Quoted 3 lines
FIT image is the one that I can think off. Since SPL is loading the FIT image,
SPL_HANDOFFcan be used to pass on the loadaddr from SPL to U-Boot and U-Boot can start the remote cores using this info.OK, just the ensure I got the idea correctly:
??- extend struct
spl_handofforarch_spl_handoffwith the fit image ??? loadaddr that spl is processingQuoted 8 lines
Yes
Quoted 4 lines
??- stick the watchdog firmware into the u-boot proper fit image ??? (generated by
tools/k3_fit_atf.shor shipped via the board folder, as ??? in our case)IMHO, not via board folder.
k3_fit_atfis used to generate a53 spl images. MayYeah, right. We also have a fit image for u-boot proper, that confused me.
Quoted 7 lines
Quoted 2 lines
be create a new one that packs fit image with u-boot and firmware. Or can you check if binman in u-boot works for you?
You mean, pack the u-boot proper with the firmware? Then we could stick the result in an signed fit image when needed. And I could read the offset of the firmware from the generated dtb - provided binman can deal with multiple configurations like we have.
If that is possible I am okay with it.
Thanks and regards,
Lokesh
Quoted 3 lines
Jan
v2 cover watchdog: K3: Add RTI watchdog support
Quoted 54 lines · Lokesh Vutla
Quoted 51 lines · Jan Kiszka
Quoted 36 lines · Lokesh Vutla
Hi Jan,
Quoted 24 lines · Jan Kiszka
Quoted 23 lines · Lokesh Vutla
Quoted 19 lines · Jan Kiszka
Quoted 9 lines · Lokesh Vutla
Quoted 6 lines · Jan Kiszka
This brings watchdog support for the TI K3 SoCs, derived from the Linux kernel, augmented with firmware loading as needed on the AM65x.
Tested on the AM65x EVM and the IOT2050 (also AM65x-based, upstream support will be posted soon).
Quoted 7 lines
Quoted 4 lines
Changes in v2:
??? - keep watchdog powered when handing over to Linux ??? - drop unneeded explicit power-on
??? - account for RTI firmware locking the power domainPatch 1 and 3 merged applied.
Thanks. Still taking workable suggestions for loading the firmware.
Quoted 8 lines
Quoted 3 lines
FIT image is the one that I can think off. Since SPL is loading the FIT image,
SPL_HANDOFFcan be used to pass on the loadaddr from SPL to U-Boot and U-Boot can start the remote cores using this info.OK, just the ensure I got the idea correctly:
??- extend struct
spl_handofforarch_spl_handoffwith the fit image ??? loadaddr that spl is processingQuoted 8 lines
Yes
Quoted 4 lines
??- stick the watchdog firmware into the u-boot proper fit image ??? (generated by
tools/k3_fit_atf.shor shipped via the board folder, as ??? in our case)IMHO, not via board folder.
k3_fit_atfis used to generate a53 spl images. MayYeah, right. We also have a fit image for u-boot proper, that confused me.
Quoted 2 lines
be create a new one that packs fit image with u-boot and firmware. Or can you check if binman in u-boot works for you?
Quoted 7 lines
Quoted 4 lines
You mean, pack the u-boot proper with the firmware? Then we could stick the result in an signed fit image when needed. And I could read the offset of the firmware from the generated dtb - provided binman can deal with multiple configurations like we have.
If that is possible I am okay with it.
I will definitely try to switch our SPI flash image generation to binman, but I didn't figure out how to use it for appending a binary to u-boot-nodtb.bin.
To my current understanding of the tool, it is only able to write back the offsets of image elements to a single dtb. That breaks when you have multiple configurations to choose from. I also have to handle
https://github.com/siemens/u-boot/blob/jan/iot2050/board/siemens/iot2050/u-boot.its,
not just u-boot.dtb.
Jan
Signature · 2 lines
Siemens AG, Corporate Technology, CT RDA IOT SES-DE Corporate Competence Center Embedded Linux
v2 cover watchdog: K3: Add RTI watchdog support
Quoted 77 lines · Jan Kiszka
Quoted 62 lines · Lokesh Vutla
Quoted 59 lines · Jan Kiszka
Quoted 43 lines · Lokesh Vutla
Hi Jan,
Quoted 32 lines · Jan Kiszka
Quoted 23 lines · Lokesh Vutla
Quoted 20 lines · Jan Kiszka
Quoted 18 lines · Lokesh Vutla
Quoted 4 lines · Jan Kiszka
This brings watchdog support for the TI K3 SoCs, derived from the Linux
kernel, augmented with firmware loading as needed on the AM65x.Quoted 8 lines
Tested on the AM65x EVM and the IOT2050 (also AM65x-based, upstream
support will be posted soon).Changes in v2:
???? - keep watchdog powered when handing over to Linux ???? - drop unneeded explicit power-on
???? - account for RTI firmware locking the power domainPatch 1 and 3 merged applied.
Quoted 7 lines
Quoted 1 line
Thanks. Still taking workable suggestions for loading the firmware.
FIT image is the one that I can think off. Since SPL is loading the FIT image,
SPL_HANDOFFcan be used to pass on the loadaddr from SPL to U-Boot and U-Boot
can start the remote cores using this info.Quoted 4 lines
OK, just the ensure I got the idea correctly:
???- extend struct
spl_handofforarch_spl_handoffwith the fit image ???? loadaddr that spl is processingYes
Quoted 1 line
Quoted 7 lines
Quoted 4 lines
???- stick the watchdog firmware into the u-boot proper fit image ???? (generated by
tools/k3_fit_atf.shor shipped via the board folder, as
???? in our case)IMHO, not via board folder.
k3_fit_atfis used to generate a53 spl images. MayYeah, right. We also have a fit image for u-boot proper, that confused me.
Quoted 3 lines
be create a new one that packs fit image with u-boot and firmware. Or can you
check if binman in u-boot works for you?Quoted 9 lines
Quoted 6 lines
You mean, pack the u-boot proper with the firmware? Then we could stick the
result in an signed fit image when needed. And I could read the offset of the
firmware from the generated dtb - provided binman can deal with multiple configurations like we have.If that is possible I am okay with it.
I will definitely try to switch our SPI flash image generation to binman, but I didn't figure out how to use it for appending a binary to u-boot-nodtb.bin.
Quoted 5 lines
To my current understanding of the tool, it is only able to write back the offsets of image elements to a single dtb. That breaks when you have multiple configurations to choose from. I also have to handle
https://github.com/siemens/u-boot/blob/jan/iot2050/board/siemens/iot2050/u-boot.its,
not just u-boot.dtb.
Just updated the branch to use binman for the flash image and also for replacing u-boot.its [1][2]. However, I still don't see how to use it for adding a firmware image into the fit parts AND finding it later on from U-Boot proper. Adding Simon, in case he has some idea.
Jan
[1]
https://github.com/siemens/u-boot/commit/951e5294f14196a502e7fe238c23c49de49b8e29
[2]
https://github.com/siemens/u-boot/blob/951e5294f14196a502e7fe238c23c49de49b8e29/arch/arm/dts/iot2050-boot-image.dtsi
Signature · 2 lines
Siemens AG, Corporate Technology, CT RDA IOT SES-DE Corporate Competence Center Embedded Linux