ARM: rockchip: add power-domains for Cortex-A9 socs
Subsystems (3)
Heiko Stuebner
maintainercover ARM: rockchip: add power-domains for Cortex-A9 socs
A small bit of cleanup for some clocks nobody used yet but that need to be toggled for the synchronous reset done on power-domain state changes.
Domain values are done by the book (aka soc documentation for pmu and power-domain <-> ip block connections) and tested with the gpu and the wip lima kernel driver on rk3188.
Heiko Stuebner (9):
clk: rockchip: add more rk3188 graphics clock ids
clk: rockchip: use new cif/vdpu clock ids on rk3188
dt-bindings: add power-domain header for RK3188 SoCs
dt-bindings: add power-domain header for RK3066 SoCs
dt-bindings: add compatibles for rk3066/rk3188 power controllers
soc: rockchip: power-domain: add rk3188 powerdomains
soc: rockchip: power-domain: add rk3066 powerdomains
ARM: dts: rockchip: add qos nodes found on rk3066 and rk3188
ARM: dts: rockchip: add rk3066/rk3188 power-domains
.../bindings/soc/rockchip/power_domain.txt | 4 ++ arch/arm/boot/dts/rk3066a.dtsi | 51 ++++++++++++++++++++++ arch/arm/boot/dts/rk3188.dtsi | 48 ++++++++++++++++++++ arch/arm/boot/dts/rk3xxx.dtsi | 40 +++++++++++++++++ drivers/clk/rockchip/clk-rk3188.c | 12 ++--- drivers/soc/rockchip/pm_domains.c | 48 ++++++++++++++++++++ include/dt-bindings/clock/rk3188-cru-common.h | 9 +++- include/dt-bindings/power/rk3066-power.h | 21 +++++++++ include/dt-bindings/power/rk3188-power.h | 23 ++++++++++ 9 files changed, 248 insertions(+), 8 deletions(-) create mode 100644 include/dt-bindings/power/rk3066-power.h create mode 100644 include/dt-bindings/power/rk3188-power.h
Signature · 1 line
2.14.1
Heiko Stuebner
maintainerPATCH 1/9 clk: rockchip: add more rk3188 graphics clock ids
Add ids for cif, v{d/e}pu clocks on rk3188. ACLK_CIF does get a needed 1 at it's end but that should be safe because no driver for the camera interface has surfaced so far and the old vendor kernels for these socs are based on linux-3.0 and still used board files then, so there really are no previous users anywhere to be found.
--- include/dt-bindings/clock/rk3188-cru-common.h | 9 +++++++-- 1 file changed, 7 insertions(+), 2 deletions(-)
include/dt-bindings/clock/rk3188-cru-common.h +7 -2
@@ -68,12 +68,14 @@#define ACLK_LCDC1 196#define ACLK_GPU 197#define ACLK_SMC 198 -#define ACLK_CIF 199 +#define ACLK_CIF1 199#define ACLK_IPP 200#define ACLK_RGA 201#define ACLK_CIF0 202#define ACLK_CPU 203#define ACLK_PERI 204 +#define ACLK_VEPU 205 +#define ACLK_VDPU 206/* pclk gates */ #define PCLK_GRF 320
@@ -134,8 +136,11 @@#define HCLK_NANDC0 467#define HCLK_CPU 468#define HCLK_PERI 469 +#define HCLK_CIF1 470 +#define HCLK_VEPU 471 +#define HCLK_VDPU 472 -#define CLK_NR_CLKS (HCLK_PERI + 1) +#define CLK_NR_CLKS (HCLK_VDPU + 1)/* soft-reset indices */ #define SRST_MCORE 2
Signature · 1 line
2.14.1
Heiko Stuebner
maintainerPATCH 1/9 clk: rockchip: add more rk3188 graphics clock ids
Am Freitag, 15. September 2017, 10:33:49 CEST schrieb Heiko Stuebner:
Quoted 7 lines
Add ids for cif, v{d/e}pu clocks on rk3188.
ACLK_CIFdoes get a needed 1 at it's end but that should be safe because no driver for the camera interface has surfaced so far and the old vendor kernels for these socs are based on linux-3.0 and still used board files then, so there really are no previous users anywhere to be found.Signed-off-by Heiko Stuebner <[email protected]>
applied for 4.15
Heiko Stuebner
maintainerPATCH 2/9 clk: rockchip: use new cif/vdpu clock ids on rk3188
In reply to Heiko StuebnerUse the new clock-ids for cif, vdpu, vepu on rk3188
--- drivers/clk/rockchip/clk-rk3188.c | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-)
drivers/clk/rockchip/clk-rk3188.c +6 -6
@@ -290,15 +290,15 @@ static struct rockchip_clk_branch common_clk_branches[] __initdata = { RK2928_CLKSEL_CON(0), 6, 2, DFLAGS | CLK_DIVIDER_READ_ONLY, div_core_peri_t, RK2928_CLKGATE_CON(0), 0, GFLAGS), -COMPOSITE (0 ,"aclk_vepu" , mux_pll_src_cpll_gpll_p,0 , +COMPOSITE (ACLK_VEPU ,"aclk_vepu" , mux_pll_src_cpll_gpll_p,0 ,RK2928_CLKSEL_CON (32 ),7 ,1 ,MFLAGS ,0 ,5 ,DFLAGS ,RK2928_CLKGATE_CON (3 ),9 ,GFLAGS ), -GATE (0 ,"hclk_vepu" ,"aclk_vepu" ,0 , +GATE (HCLK_VEPU ,"hclk_vepu" ,"aclk_vepu" ,0 ,RK2928_CLKGATE_CON (3 ),10 ,GFLAGS ), -COMPOSITE (0 ,"aclk_vdpu" , mux_pll_src_cpll_gpll_p,0 , +COMPOSITE (ACLK_VDPU ,"aclk_vdpu" , mux_pll_src_cpll_gpll_p,0 ,RK2928_CLKSEL_CON (32 ),15 ,1 ,MFLAGS ,8 ,5 ,DFLAGS ,RK2928_CLKGATE_CON (3 ),11 ,GFLAGS ), -GATE (0 ,"hclk_vdpu" ,"aclk_vdpu" ,0 , +GATE (HCLK_VDPU ,"hclk_vdpu" ,"aclk_vdpu" ,0 ,RK2928_CLKGATE_CON (3 ),12 ,GFLAGS ), GATE(0, "gpll_ddr", "gpll", CLK_IGNORE_UNUSED,
@@ -644,13 +644,13 @@ static struct rockchip_clk_branch rk3066a_clk_branches[] __initdata = {GATE (HCLK_I2S1 ,"hclk_i2s1" ,"hclk_cpu" ,0 ,RK2928_CLKGATE_CON (7 ),3 ,GFLAGS ),GATE (HCLK_I2S2 ,"hclk_i2s2" ,"hclk_cpu" ,0 ,RK2928_CLKGATE_CON (7 ),4 ,GFLAGS ), -GATE (0 ,"hclk_cif1" ,"hclk_cpu" ,0 ,RK2928_CLKGATE_CON (6 ),6 ,GFLAGS ), +GATE (HCLK_CIF1 ,"hclk_cif1" ,"hclk_cpu" ,0 ,RK2928_CLKGATE_CON (6 ),6 ,GFLAGS ),GATE (0 ,"hclk_hdmi" ,"hclk_cpu" ,0 ,RK2928_CLKGATE_CON (4 ),14 ,GFLAGS ),GATE (HCLK_OTG1 ,"hclk_usbotg1" ,"hclk_peri" ,CLK_IGNORE_UNUSED ,RK2928_CLKGATE_CON (5 ),14 ,GFLAGS ), -GATE (0 ,"aclk_cif1" ,"aclk_vio1" ,0 ,RK2928_CLKGATE_CON (6 ),7 ,GFLAGS ), +GATE (ACLK_CIF1 ,"aclk_cif1" ,"aclk_vio1" ,0 ,RK2928_CLKGATE_CON (6 ),7 ,GFLAGS ),GATE (PCLK_TIMER1 ,"pclk_timer1" ,"pclk_cpu" ,0 ,RK2928_CLKGATE_CON (7 ),8 ,GFLAGS ), GATE(PCLK_TIMER2, "pclk_timer2", "pclk_cpu", 0, RK2928_CLKGATE_CON(7), 9, GFLAGS),
Signature · 1 line
2.14.1
Heiko Stuebner
maintainerPATCH 2/9 clk: rockchip: use new cif/vdpu clock ids on rk3188
Am Freitag, 15. September 2017, 10:33:50 CEST schrieb Heiko Stuebner:
Quoted 3 lines
Use the new clock-ids for cif, vdpu, vepu on rk3188
Signed-off-by Heiko Stuebner <[email protected]>
applied for 4.15
Heiko Stuebner
maintainerPATCH 3/9 dt-bindings: add power-domain header for RK3188 SoCs
In reply to Heiko StuebnerAdd rk3188 power-domains as described by the TRM.
--- include/dt-bindings/power/rk3188-power.h | 23 +++++++++++++++++++++++ 1 file changed, 23 insertions(+) create mode 100644 include/dt-bindings/power/rk3188-power.h
include/dt-bindings/power/rk3188-power.h new file +23 -0
@@ -0,0 +1,23 @@ +#ifndef __DT_BINDINGS_POWER_RK3188_POWER_H__ +#define __DT_BINDINGS_POWER_RK3188_POWER_H__ + +/* VD_CORE */ +#define RK3188_PD_A9_0 0 +#define RK3188_PD_A9_1 1 +#define RK3188_PD_A9_2 2 +#define RK3188_PD_A9_3 3 +#define RK3188_PD_DBG 4 +#define RK3188_PD_SCU 5 + +/* VD_LOGIC */ +#define RK3188_PD_VIDEO 6 +#define RK3188_PD_VIO 7 +#define RK3188_PD_GPU 8 +#define RK3188_PD_PERI 9 +#define RK3188_PD_CPU 10 +#define RK3188_PD_ALIVE 11 + +/* VD_PMU */ +#define RK3188_PD_RTC 12 + +#endif
Signature · 1 line
2.14.1
Heiko Stuebner
maintainerPATCH 4/9 dt-bindings: add power-domain header for RK3066 SoCs
In reply to Heiko StuebnerAdd rk3066 power-domains as described by the TRM.
--- include/dt-bindings/power/rk3066-power.h | 21 +++++++++++++++++++++ 1 file changed, 21 insertions(+) create mode 100644 include/dt-bindings/power/rk3066-power.h
include/dt-bindings/power/rk3066-power.h new file +21 -0
@@ -0,0 +1,21 @@ +#ifndef __DT_BINDINGS_POWER_RK3066_POWER_H__ +#define __DT_BINDINGS_POWER_RK3066_POWER_H__ + +/* VD_CORE */ +#define RK3066_PD_A9_0 0 +#define RK3066_PD_A9_1 1 +#define RK3066_PD_DBG 4 +#define RK3066_PD_SCU 5 + +/* VD_LOGIC */ +#define RK3066_PD_VIDEO 6 +#define RK3066_PD_VIO 7 +#define RK3066_PD_GPU 8 +#define RK3066_PD_PERI 9 +#define RK3066_PD_CPU 10 +#define RK3066_PD_ALIVE 11 + +/* VD_PMU */ +#define RK3066_PD_RTC 12 + +#endif
Signature · 1 line
2.14.1
Heiko Stuebner
maintainerPATCH 5/9 dt-bindings: add compatibles for rk3066/rk3188 power controllers
In reply to Heiko StuebnerAdd the compatible values for the power-domain controllers found on rk3066 and rk3188.
--- Documentation/devicetree/bindings/soc/rockchip/power_domain.txt | 4 ++++ 1 file changed, 4 insertions(+)
Documentation/devicetree/bindings/soc/rockchip/power_domain.txt +4 -0
@@ -5,6 +5,8 @@ powered up/down by software based on different application scenes to save power. Required properties for power domain controller: - compatible: Should be one of the following. + "rockchip,rk3066-power-controller" - for RK3288 SoCs. + "rockchip,rk3188-power-controller" - for RK3288 SoCs. "rockchip,rk3288-power-controller" - for RK3288 SoCs. "rockchip,rk3328-power-controller" - for RK3328 SoCs. "rockchip,rk3366-power-controller" - for RK3366 SoCs.
@@ -17,6 +19,8 @@ Required properties for power domain controller: Required properties for power domain sub nodes: - reg: index of the power domain, should use macros in: + "include/dt-bindings/power/rk3066-power.h" - for RK3288 type power domain. + "include/dt-bindings/power/rk3188-power.h" - for RK3288 type power domain. "include/dt-bindings/power/rk3288-power.h" - for RK3288 type power domain. "include/dt-bindings/power/rk3328-power.h" - for RK3328 type power domain. "include/dt-bindings/power/rk3366-power.h" - for RK3366 type power domain.
Signature · 1 line
2.14.1
PATCH 5/9 dt-bindings: add compatibles for rk3066/rk3188 power controllers
Hello Heiko,
There are a few copy/paste errors in the documentation.
Le 15/09/2017 ? 10:33, Heiko Stuebner a ?crit?:
Quoted 13 lines
Add the compatible values for the power-domain controllers found on rk3066 and rk3188.
Signed-off-by Heiko Stuebner <[email protected]>--- Documentation/devicetree/bindings/soc/rockchip/power_domain.txt | 4 ++++ 1 file changed, 4 insertions(+)Documentation/devicetree/bindings/soc/rockchip/power_domain.txt +0
-0
Documentation/devicetree/bindings/soc/rockchip/power_domain.txt powered up/down by software based on different application scenes to save power. · line 9
Quoted 5 lines
Documentation/devicetree/bindings/soc/rockchip/power_domain.txt +2
-0@@ -5,6 +5,8 @@ powered up/down by software based on different application scenes to save power. Required properties for power domain controller: - compatible: Should be one of the following. + "rockchip,rk3066-power-controller" - for RK3288 SoCs. + "rockchip,rk3188-power-controller" - for RK3288 SoCs.
These should be for RK3066 and RK3188.
Documentation/devicetree/bindings/soc/rockchip/power_domain.txt Required properties for power domain controller: · line 23
Quoted 9 lines
Documentation/devicetree/bindings/soc/rockchip/power_domain.txt +2
-0"rockchip,rk3288-power-controller" - for RK3288 SoCs. "rockchip,rk3328-power-controller" - for RK3328 SoCs. "rockchip,rk3366-power-controller" - for RK3366 SoCs.@@ -17,6 +19,8 @@ Required properties for power domain controller: Required properties for power domain sub nodes: - reg: index of the power domain, should use macros in: + "include/dt-bindings/power/rk3066-power.h" - for RK3288 type power domain. + "include/dt-bindings/power/rk3188-power.h" - for RK3288 type power domain.
Same here.
Documentation/devicetree/bindings/soc/rockchip/power_domain.txt Required properties for power domain controller: · line 26
Quoted 3 lines
Documentation/devicetree/bindings/soc/rockchip/power_domain.txt +0
-0"include/dt-bindings/power/rk3288-power.h" - for RK3288 type power domain. "include/dt-bindings/power/rk3328-power.h" - for RK3328 type power domain. "include/dt-bindings/power/rk3366-power.h" - for RK3366 type power domain.
Julien
Heiko Stuebner
maintainerPATCH 5/9 dt-bindings: add compatibles for rk3066/rk3188 power controllers
Am Samstag, 16. September 2017, 23:04:48 CEST schrieb Julien Chauveau:
Quoted 30 lines
Hello Heiko,
There are a few copy/paste errors in the documentation.
Le 15/09/2017 ? 10:33, Heiko Stuebner a ?crit :
Quoted 13 lines
Add the compatible values for the power-domain controllers found on rk3066 and rk3188.
Signed-off-by Heiko Stuebner <[email protected]>--- Documentation/devicetree/bindings/soc/rockchip/power_domain.txt | 4 ++++ 1 file changed, 4 insertions(+)Documentation/devicetree/bindings/soc/rockchip/power_domain.txt +0
-0Documentation/devicetree/bindings/soc/rockchip/power_domain.txt powered up/down by software based on different application scenes to save power. · line 9
Quoted 5 lines
Documentation/devicetree/bindings/soc/rockchip/power_domain.txt +2
-0@@ -5,6 +5,8 @@ powered up/down by software based on different application scenes to save power. Required properties for power domain controller: - compatible: Should be one of the following. + "rockchip,rk3066-power-controller" - for RK3288 SoCs. + "rockchip,rk3188-power-controller" - for RK3288 SoCs.These should be for RK3066 and RK3188.
Quoted 5 lines
Documentation/devicetree/bindings/soc/rockchip/power_domain.txt +0
-0"rockchip,rk3288-power-controller" - for RK3288 SoCs. "rockchip,rk3328-power-controller" - for RK3328 SoCs. "rockchip,rk3366-power-controller" - for RK3366 SoCs.@@ -17,6 +19,8 @@ Required properties for power domain controller:
Quoted 5 lines
Documentation/devicetree/bindings/soc/rockchip/power_domain.txt Required properties for power domain controller: · line 23
Quoted 4 lines
Documentation/devicetree/bindings/soc/rockchip/power_domain.txt +2
-0Required properties for power domain sub nodes: - reg: index of the power domain, should use macros in: + "include/dt-bindings/power/rk3066-power.h" - for RK3288 type power domain. + "include/dt-bindings/power/rk3188-power.h" - for RK3288 type power domain.Same here.
bah ... thanks for noticing. Will fix in a v2 shortly.
Thanks
Heiko
Quoted 6 lines
Documentation/devicetree/bindings/soc/rockchip/power_domain.txt Required properties for power domain controller: · line 26
Quoted 3 lines
Documentation/devicetree/bindings/soc/rockchip/power_domain.txt +0
-0"include/dt-bindings/power/rk3288-power.h" - for RK3288 type power domain. "include/dt-bindings/power/rk3328-power.h" - for RK3328 type power domain. "include/dt-bindings/power/rk3366-power.h" - for RK3366 type power domain.Julien
Heiko Stuebner
maintainerPATCH 6/9 soc: rockchip: power-domain: add rk3188 powerdomains
In reply to Heiko StuebnerAdd power-domains found on rk3188 socs.
--- drivers/soc/rockchip/pm_domains.c | 24 ++++++++++++++++++++++++ 1 file changed, 24 insertions(+)
drivers/soc/rockchip/pm_domains.c +24 -0
@@ -18,6 +18,7 @@#include <linux/clk.h> #include <linux/regmap.h> #include <linux/mfd/syscon.h> +#include <dt-bindings/power/rk3188-power.h> #include <dt-bindings/power/rk3288-power.h> #include <dt-bindings/power/rk3328-power.h> #include <dt-bindings/power/rk3366-power.h>
@@ -712,6 +713,14 @@ static int rockchip_pm_domain_probe(struct platform_device *pdev)return error; } +static const struct rockchip_domain_info rk3188_pm_domains[] = { + [RK3188_PD_GPU ] =DOMAIN (9 ,9 ,3 ,24 ,29 , false), + [RK3188_PD_VIDEO ] =DOMAIN (8 ,8 ,4 ,23 ,28 , false), + [RK3188_PD_VIO ] =DOMAIN (7 ,7 ,5 ,22 ,27 , false), + [RK3188_PD_PERI ] =DOMAIN (6 ,6 ,2 ,25 ,30 , false), + [RK3188_PD_CPU ] =DOMAIN (5 ,5 ,1 ,26 ,31 , false), +}; +static const struct rockchip_domain_info rk3288_pm_domains[] = { [RK3288_PD_VIO ] =DOMAIN_RK3288 (7 ,7 ,4 , false), [RK3288_PD_HEVC ] =DOMAIN_RK3288 (14 ,10 ,9 , false),
@@ -779,6 +788,17 @@ static const struct rockchip_domain_info rk3399_pm_domains[] = { [RK3399_PD_SDIOAUDIO] = DOMAIN_RK3399(31, 31, 29, true), }; +static const struct rockchip_pmu_info rk3188_pmu = { + .pwr_offset =0x08 , + .status_offset =0x0c , + .req_offset =0x38 ,/* PMU_MISC_CON1 */ + .idle_offset =0x0c , + .ack_offset =0x0c , + + .num_domains =ARRAY_SIZE (rk3188_pm_domains), + .domain_info = rk3188_pm_domains, +}; +static const struct rockchip_pmu_info rk3288_pmu = { .pwr_offset =0x08 , .status_offset =0x0c ,
@@ -853,6 +873,10 @@ static const struct rockchip_pmu_info rk3399_pmu = { };static const struct of_device_id rockchip_pm_domain_dt_match[] = { + { + .compatible ="rockchip,rk3188-power-controller" , + .data = (void *)&rk3188_pmu, + }, { .compatible ="rockchip,rk3288-power-controller" , .data = (void *)&rk3288_pmu,
Signature · 1 line
2.14.1
Heiko Stuebner
maintainerPATCH 7/9 soc: rockchip: power-domain: add rk3066 powerdomains
In reply to Heiko StuebnerAdd power-domains found on rk3066 socs.
--- drivers/soc/rockchip/pm_domains.c | 24 ++++++++++++++++++++++++ 1 file changed, 24 insertions(+)
drivers/soc/rockchip/pm_domains.c +24 -0
@@ -18,6 +18,7 @@#include <linux/clk.h> #include <linux/regmap.h> #include <linux/mfd/syscon.h> +#include <dt-bindings/power/rk3066-power.h> #include <dt-bindings/power/rk3188-power.h> #include <dt-bindings/power/rk3288-power.h> #include <dt-bindings/power/rk3328-power.h>
@@ -713,6 +714,14 @@ static int rockchip_pm_domain_probe(struct platform_device *pdev)return error; } +static const struct rockchip_domain_info rk3066_pm_domains[] = { + [RK3066_PD_GPU ] =DOMAIN (9 ,9 ,3 ,24 ,29 , false), + [RK3066_PD_VIDEO ] =DOMAIN (8 ,8 ,4 ,23 ,28 , false), + [RK3066_PD_VIO ] =DOMAIN (7 ,7 ,5 ,22 ,27 , false), + [RK3066_PD_PERI ] =DOMAIN (6 ,6 ,2 ,25 ,30 , false), + [RK3066_PD_CPU ] =DOMAIN (-1 ,5 ,1 ,26 ,31 , false), +}; +static const struct rockchip_domain_info rk3188_pm_domains[] = { [RK3188_PD_GPU ] =DOMAIN (9 ,9 ,3 ,24 ,29 , false), [RK3188_PD_VIDEO ] =DOMAIN (8 ,8 ,4 ,23 ,28 , false),
@@ -788,6 +797,17 @@ static const struct rockchip_domain_info rk3399_pm_domains[] = { [RK3399_PD_SDIOAUDIO] = DOMAIN_RK3399(31, 31, 29, true), }; +static const struct rockchip_pmu_info rk3066_pmu = { + .pwr_offset =0x08 , + .status_offset =0x0c , + .req_offset =0x38 ,/* PMU_MISC_CON1 */ + .idle_offset =0x0c , + .ack_offset =0x0c , + + .num_domains =ARRAY_SIZE (rk3066_pm_domains), + .domain_info = rk3066_pm_domains, +}; +static const struct rockchip_pmu_info rk3188_pmu = { .pwr_offset =0x08 , .status_offset =0x0c ,
@@ -873,6 +893,10 @@ static const struct rockchip_pmu_info rk3399_pmu = { };static const struct of_device_id rockchip_pm_domain_dt_match[] = { + { + .compatible ="rockchip,rk3066-power-controller" , + .data = (void *)&rk3066_pmu, + }, { .compatible ="rockchip,rk3188-power-controller" , .data = (void *)&rk3188_pmu,
Signature · 1 line
2.14.1
Heiko Stuebner
maintainerPATCH 8/9 ARM: dts: rockchip: add qos nodes found on rk3066 and rk3188
In reply to Heiko StuebnerQoS nodes keep information about priorites etc on the interconnect and loose state when the power-domain gets disabled. Therefore the power-domain driver stores the settings of available qos nodes and restores them when the power-domain gets enabled again.
So add the qos nodes found on the Cortex-A9 socs from Rockchip, so that they can then be connected to the power-domains.
--- arch/arm/boot/dts/rk3xxx.dtsi | 40 ++++++++++++++++++++++++++++++++++++++++ 1 file changed, 40 insertions(+)
arch/arm/boot/dts/rk3xxx.dtsi +40 -0
@@ -184,6 +184,46 @@ status = "disabled"; }; + qos_gpu: qos at 1012d000 { + compatible = "syscon"; + reg = <0x1012d000 0x20>; + }; + + qos_vpu: qos at 1012e000 { + compatible = "syscon"; + reg = <0x1012e000 0x20>; + }; + + qos_lcdc0: qos at 1012f000 { + compatible = "syscon"; + reg = <0x1012f000 0x20>; + }; + + qos_cif0: qos at 1012f080 { + compatible = "syscon"; + reg = <0x1012f080 0x20>; + }; + + qos_ipp: qos at 1012f100 { + compatible = "syscon"; + reg = <0x1012f100 0x20>; + }; + + qos_lcdc1: qos at 1012f180 { + compatible = "syscon"; + reg = <0x1012f180 0x20>; + }; + + qos_cif1: qos at 1012f200 { + compatible = "syscon"; + reg = <0x1012f200 0x20>; + }; + + qos_rga: qos at 1012f280 { + compatible = "syscon"; + reg = <0x1012f280 0x20>; + }; + usb_otg: usb at 10180000 { compatible = "rockchip,rk3066-usb", "snps,dwc2"; reg = <0x10180000 0x40000>;
Signature · 1 line
2.14.1
Heiko Stuebner
maintainerPATCH 9/9 ARM: dts: rockchip: add rk3066/rk3188 power-domains
In reply to Heiko StuebnerAdd the power-domain nodes to both rk3066 and rk3188 including their clocks and qos connections.
--- arch/arm/boot/dts/rk3066a.dtsi | 51 ++++++++++++++++++++++++++++++++++++++++++ arch/arm/boot/dts/rk3188.dtsi | 48 +++++++++++++++++++++++++++++++++++++++ 2 files changed, 99 insertions(+)
arch/arm/boot/dts/rk3066a.dtsi +51 -0
@@ -44,6 +44,7 @@ #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/pinctrl/rockchip.h> #include <dt-bindings/clock/rk3066a-cru.h> +#include <dt-bindings/power/rk3066-power.h> #include "rk3xxx.dtsi" / {
@@ -680,6 +681,56 @@ dma-names = "rx-tx"; }; +&pmu { + power: power-controller { + compatible = "rockchip,rk3066-power-controller"; + #power-domain-cells = <1>; + #address-cells = <1>; + #size-cells = <0>; + + pd_vio at RK3066_PD_VIO { + reg = <RK3066_PD_VIO>; + clocks = <&cru ACLK_LCDC0>, + <&cru ACLK_LCDC1>, + <&cru DCLK_LCDC0>, + <&cru DCLK_LCDC1>, + <&cru HCLK_LCDC0>, + <&cru HCLK_LCDC1>, + <&cru SCLK_CIF1>, + <&cru ACLK_CIF1>, + <&cru HCLK_CIF1>, + <&cru SCLK_CIF0>, + <&cru ACLK_CIF0>, + <&cru HCLK_CIF0>, + <&cru ACLK_IPP>, + <&cru HCLK_IPP>, + <&cru ACLK_RGA>, + <&cru HCLK_RGA>; + pm_qos = <&qos_lcdc0>, + <&qos_lcdc1>, + <&qos_cif0>, + <&qos_cif1>, + <&qos_ipp>, + <&qos_rga>; + }; + + pd_video at RK3066_PD_VIDEO { + reg = <RK3066_PD_VIDEO>; + clocks = <&cru ACLK_VDPU>, + <&cru ACLK_VEPU>, + <&cru HCLK_VDPU>, + <&cru HCLK_VEPU>; + pm_qos = <&qos_vpu>; + }; + + pd_gpu at RK3066_PD_GPU { + reg = <RK3066_PD_GPU>; + clocks = <&cru ACLK_GPU>; + pm_qos = <&qos_gpu>; + }; + }; +}; + &pwm0 { pinctrl-names = "default"; pinctrl-0 = <&pwm0_out>;
arch/arm/boot/dts/rk3188.dtsi +48 -0
60 lines not on this page · raw message
Signature · 1 line
2.14.1