Skip to contentSkip to conversation

Pull request: u-boot-imx u -boot-imx-20190101

GIT PULL Stefano Babic 2 participants 5 messages Jan 1, 2019 – Jan 9, 2019

lore
Share & tools
lore
#0 lore raw

Hi Tom,

I dropped for the moment the following patches from Denis:

bootcount: i2c: Add bus switching to the I2C bootcount driver
bootcount: Configure length limit for I2C bootcount
board: ge: Store bootcount in EEPROM on PPD and Bx50v3

I used the same hack and PowerPC boards are built successfully on travis. Please pull from u-boot-imx, thanks !

The following changes since commit d117d8f19b0625f88309e47a8a32c2faa384dddc:

Merge branch 'master' of git://git.denx.de/u-boot-i2c (2018-12-13
09:36:55 -0500)

are available in the Git repository at:

git://www.denx.de/git/u-boot-imx.git tags/u-boot-imx-20190101

for you to fetch changes up to 57d2beb91d705bccdfee5e9e5fd267f5e363a100:

pico-imx7d: Increase the CONFIG_ENV_OFFSET size (2019-01-01 14:12:18
+0100)

----------------------------------------------------------------
imx for 2019.01

- introduce support for i.MX8M
- fix size limit for Vhybrid / pico boards
- several board fixes
- w1 driver for MX2x / MX5x

----------------------------------------------------------------
Denis Zalevskiy (3):
board: ge: Remove EEPROM bus param from read_vpd()
board: ge: Move VPD EEPROM configuration to the defconfig
board: ge: Move VPD reading to the vpd_reader

Fabien Lahoudere (1):
embestmx6boards: Add SPL support

Fabio Estevam (1):
pico-imx7d: Increase the CONFIG_ENV_OFFSET size

Gary Bisson (2):
imx: mx8m: add memory mapping for CAAM and TCM
imx: bootaux: fix stack and pc assignment on 64-bit platforms

Harald Seiler (1):
pcm058: fix NAND flash not using badblock table

Lukasz Majewski (6):
ARM: vybrid: Provide pinctrl driver for Vybrid (vf610)
ARM: DTS: Add iomux node to vf.dtsi for Vybrid devices
ARM: DTS: Provide pinfunc definitions for vybrid vf610 from Linux
kernel
nand: vybrid: Use calloc() instead of malloc() to allocate struct nfc
Kconfig: Add entry for VF610 NAND NFC device tree aware driver
nand: vybrid: Extend the vf610 NFC NAND driver to support device
tree (and DM)

Martin Fuzzey (1):
w1: Add driver for i.MX bus master controller

Martin Husemann (1):
tools: improve portability of imx_cntr_image.sh

Michael Heimpold (4):
configs: mx23_olinuxino_defconfig: fix status led definition
configs: mx23_olinuxino_defconfig: disable bootefi command
doc: imx: fix typo in imximage.txt
doc: imx: fix typos in mxsimage.txt

Parthiban Nallathambi (1):
imx: hab: extend hab_auth_img to calculate ivt_offset

Peng Fan (19):
imx: imx8qxp_mek: imximage: remove config.h
spl: introduce function prototypes
tools: add i.MX8M image support
arm: imx8qxp: build u-boot-dtb.cfgout before checking files Introduce CONFIG_FIT_EXTERNAL_OFFSET
imx: cpu: add CHIP_REV_2_1 macro
imx: introduce is_imx8mq helper
imx: rename mx8m,MX8M to imx8m,IMX8M
imx: spl: add MMC BOOT Device for i.MX8M
imx: imx8m: clock refactor dram pll part
imx: imx8m: introduce script to generate fit image
imx: imx8m: introduce imximage cfg file
imx: imx8mq: build flash.bin
imx: imx8m: not build bootaux when building SPL
imx: imx8m: add lpddr4 header file
drivers: ddr: introduce DDR driver for i.MX8M
imx: add i.MX8MQ EVK support
imx8m: ddr: removed unused macros
imx: mx53ppd: fix build error

Pierre-Jean Texier (1):
warp7: configs: add CONFIG_FIT option

Xiaoliang Yang (2):
watchdog: driver support for fsl-lsch2
watchdog: imx: add config to disable wdog reset

Yaniv Levinsky (1):
arm: imx7d: cl-som-imx7: migration to CONFIG_BLK

Ye Li (2):
SPL: Add HAB image authentication to FIT
imx8m: Enable CONFIG_SPL_FIT_IMAGE_TINY for iMX8M

Kconfig
| 10 +
Makefile
| 7 +-
arch/arm/Kconfig
| 4 +-
arch/arm/Makefile
| 4 +-
arch/arm/cpu/armv8/fsl-layerscape/doc/README.lsch2
| 11 +
arch/arm/dts/Makefile
| 2 +
arch/arm/dts/fsl-imx8mq-evk.dts
| 414 ++++++++++++++
arch/arm/dts/vf.dtsi
| 6 +
arch/arm/dts/vf610-pinfunc.h
| 810 ++++++++++++++++++++++++++
arch/arm/include/asm/arch-imx/cpu.h
| 5 +-
arch/arm/include/asm/{arch-mx8m => arch-imx8m}/clock.h
| 22 +
arch/arm/include/asm/{arch-mx8m => arch-imx8m}/crm_regs.h
| 4 +-
arch/arm/include/asm/arch-imx8m/ddr.h
| 740 ++++++++++++++++++++++++
arch/arm/include/asm/{arch-mx8m => arch-imx8m}/gpio.h
| 4 +-
arch/arm/include/asm/{arch-mx8m => arch-imx8m}/imx-regs.h
| 4 +-
arch/arm/include/asm/{arch-mx8m/mx8mq_pins.h =>
arch-imx8m/imx8mq_pins.h} | 4 +-
arch/arm/include/asm/arch-imx8m/lpddr4_define.h
| 97 ++++
arch/arm/include/asm/{arch-mx8m => arch-imx8m}/sys_proto.h
| 4 +-
arch/arm/include/asm/arch-mx8m/ddr.h
| 355 ------------
arch/arm/include/asm/mach-imx/iomux-v3.h
| 2 +-
arch/arm/include/asm/mach-imx/regs-lcdif.h
| 6 +-
arch/arm/include/asm/mach-imx/sys_proto.h
| 3 +-
arch/arm/mach-imx/Makefile
| 37 +-
arch/arm/mach-imx/cpu.c
| 16 +-
arch/arm/mach-imx/hab.c
| 29 +-
arch/arm/mach-imx/imx8m/Kconfig
| 23 +
arch/arm/mach-imx/{mx8m => imx8m}/Makefile
| 0
arch/arm/mach-imx/{mx8m => imx8m}/clock.c
| 138 ++++-
arch/arm/mach-imx/{mx8m => imx8m}/clock_slice.c
| 0
arch/arm/mach-imx/imx8m/imximage.cfg
| 17 +
arch/arm/mach-imx/{mx8m => imx8m}/lowlevel_init.S
| 0
arch/arm/mach-imx/{mx8m => imx8m}/soc.c
| 16 +
arch/arm/mach-imx/imx_bootaux.c
| 8 +-
arch/arm/mach-imx/mkimage_fit_atf.sh
| 137 +++++
arch/arm/mach-imx/mx6/Kconfig
| 1 +
arch/arm/mach-imx/mx8m/Kconfig
| 10 -
arch/arm/mach-imx/spl.c
| 59 +-
board/embest/mx6boards/MAINTAINERS
| 1 +
board/embest/mx6boards/mx6boards.c
| 48 ++
board/freescale/imx8mq_evk/Kconfig
| 12 +
board/freescale/imx8mq_evk/MAINTAINERS
| 6 +
board/freescale/imx8mq_evk/Makefile
| 12 +
board/freescale/imx8mq_evk/README
| 36 ++
board/freescale/imx8mq_evk/imx8mq_evk.c
| 130 +++++
board/freescale/imx8mq_evk/lpddr4_timing.c
| 1320 +++++++++++++++++++++++++++++++++++++++++++
board/freescale/imx8mq_evk/lpddr4_timing_b0.c
| 1191 ++++++++++++++++++++++++++++++++++++++
board/freescale/imx8mq_evk/spl.c
| 246 ++++++++
board/freescale/imx8qxp_mek/imximage.cfg
| 1 -
board/ge/bx50v3/Kconfig
| 2 +
board/ge/bx50v3/bx50v3.c
| 57 +-
board/ge/common/Kconfig
| 14 +
board/ge/common/vpd_reader.c
| 37 +-
board/ge/common/vpd_reader.h
| 16 +-
board/ge/mx53ppd/Kconfig
| 2 +
board/ge/mx53ppd/mx53ppd.c
| 50 +-
common/image.c
| 1 +
common/spl/Kconfig
| 1 +
common/spl/spl_fit.c
| 21 +-
configs/cl-som-imx7_defconfig
| 6 +-
configs/ge_bx50v3_defconfig
| 9 +
configs/imx8mq_evk_defconfig
| 37 ++
configs/mx23_olinuxino_defconfig
| 3 +-
configs/mx53ppd_defconfig
| 10 +
configs/riotboard_spl_defconfig
| 48 ++
configs/warp7_defconfig
| 2 +
doc/device-tree-bindings/w1/mxc-w1.txt
| 37 ++
doc/imx/mkimage/imximage.txt
| 2 +-
doc/imx/mkimage/mxsimage.txt
| 4 +-
drivers/Makefile
| 1 +
drivers/ddr/Kconfig
| 1 +
drivers/ddr/imx/Kconfig
| 1 +
drivers/ddr/imx/imx8m/Kconfig
| 22 +
drivers/ddr/imx/imx8m/Makefile
| 11 +
drivers/ddr/imx/imx8m/ddr4_init.c
| 113 ++++
drivers/ddr/imx/imx8m/ddrphy_csr.c
| 732 ++++++++++++++++++++++++
drivers/ddr/imx/imx8m/ddrphy_train.c
| 86 +++
drivers/ddr/imx/imx8m/ddrphy_utils.c
| 186 ++++++
drivers/ddr/imx/imx8m/helper.c
| 170 ++++++
drivers/ddr/imx/imx8m/lpddr4_init.c
| 188 ++++++
drivers/gpio/mxc_gpio.c
| 18 +-
drivers/misc/mxc_ocotp.c
| 6 +-
drivers/mmc/fsl_esdhc.c
| 8 +-
drivers/mtd/nand/raw/Kconfig
| 11 +
drivers/mtd/nand/raw/vf610_nfc.c
| 49 +-
drivers/net/fec_mxc.c
| 2 +-
drivers/pinctrl/nxp/Kconfig
| 14 +
drivers/pinctrl/nxp/Makefile
| 1 +
drivers/pinctrl/nxp/pinctrl-vf610.c
| 40 ++
drivers/w1/Kconfig
| 14 +
drivers/w1/Makefile
| 1 +
drivers/w1/mxc_w1.c
| 232 ++++++++
drivers/watchdog/Kconfig
| 6 +
drivers/watchdog/Makefile
| 2 +
drivers/watchdog/imx_watchdog.c
| 9 +
include/configs/embestmx6boards.h
| 13 +
include/configs/imx8mq_evk.h
| 252 +++++++++
include/configs/pcm058.h
| 1 +
include/configs/pico-imx7d.h
| 14 +-
include/image.h
| 1 +
include/imximage.h
| 17 +-
include/spl.h
| 13 +
tools/Makefile
| 1 +
tools/imagetool.h
| 1 +
tools/imx8m_image.sh
| 43 ++
tools/imx8mimage.c
| 623 ++++++++++++++++++++
tools/imx_cntr_image.sh
| 2 +-
tools/mkimage.c
| 7 +

 107 files changed, 8719 insertions(+), 564 deletions(-)
 create mode 100644 arch/arm/dts/fsl-imx8mq-evk.dts
 create mode 100644 arch/arm/dts/vf610-pinfunc.h
 rename arch/arm/include/asm/{arch-mx8m => arch-imx8m}/clock.h (97%)
 rename arch/arm/include/asm/{arch-mx8m => arch-imx8m}/crm_regs.h (65%)
 create mode 100644 arch/arm/include/asm/arch-imx8m/ddr.h
 rename arch/arm/include/asm/{arch-mx8m => arch-imx8m}/gpio.h (63%)
 rename arch/arm/include/asm/{arch-mx8m => arch-imx8m}/imx-regs.h (99%)
 rename arch/arm/include/asm/{arch-mx8m/mx8mq_pins.h =>
arch-imx8m/imx8mq_pins.h} (99%)
 create mode 100644 arch/arm/include/asm/arch-imx8m/lpddr4_define.h
 rename arch/arm/include/asm/{arch-mx8m => arch-imx8m}/sys_proto.h (82%)
 delete mode 100644 arch/arm/include/asm/arch-mx8m/ddr.h
 create mode 100644 arch/arm/mach-imx/imx8m/Kconfig
 rename arch/arm/mach-imx/{mx8m => imx8m}/Makefile (100%)
 rename arch/arm/mach-imx/{mx8m => imx8m}/clock.c (85%)
 rename arch/arm/mach-imx/{mx8m => imx8m}/clock_slice.c (100%)
 create mode 100644 arch/arm/mach-imx/imx8m/imximage.cfg
 rename arch/arm/mach-imx/{mx8m => imx8m}/lowlevel_init.S (100%)
 rename arch/arm/mach-imx/{mx8m => imx8m}/soc.c (92%)
 create mode 100755 arch/arm/mach-imx/mkimage_fit_atf.sh
 delete mode 100644 arch/arm/mach-imx/mx8m/Kconfig
 create mode 100644 board/freescale/imx8mq_evk/Kconfig
 create mode 100644 board/freescale/imx8mq_evk/MAINTAINERS
 create mode 100644 board/freescale/imx8mq_evk/Makefile
 create mode 100644 board/freescale/imx8mq_evk/README
 create mode 100644 board/freescale/imx8mq_evk/imx8mq_evk.c
 create mode 100644 board/freescale/imx8mq_evk/lpddr4_timing.c
 create mode 100644 board/freescale/imx8mq_evk/lpddr4_timing_b0.c
 create mode 100644 board/freescale/imx8mq_evk/spl.c
 create mode 100644 board/ge/common/Kconfig
 create mode 100644 configs/imx8mq_evk_defconfig
 create mode 100644 configs/riotboard_spl_defconfig
 create mode 100644 doc/device-tree-bindings/w1/mxc-w1.txt
 create mode 100644 drivers/ddr/imx/Kconfig
 create mode 100644 drivers/ddr/imx/imx8m/Kconfig
 create mode 100644 drivers/ddr/imx/imx8m/Makefile
 create mode 100644 drivers/ddr/imx/imx8m/ddr4_init.c
 create mode 100644 drivers/ddr/imx/imx8m/ddrphy_csr.c
 create mode 100644 drivers/ddr/imx/imx8m/ddrphy_train.c
 create mode 100644 drivers/ddr/imx/imx8m/ddrphy_utils.c
 create mode 100644 drivers/ddr/imx/imx8m/helper.c
 create mode 100644 drivers/ddr/imx/imx8m/lpddr4_init.c
 create mode 100644 drivers/pinctrl/nxp/pinctrl-vf610.c
 create mode 100644 drivers/w1/mxc_w1.c
 create mode 100644 include/configs/imx8mq_evk.h
 create mode 100755 tools/imx8m_image.sh
 create mode 100644 tools/imx8mimage.c

Best regards,
Stefano

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
#1 lore raw
Quoted 16 lines · Stefano Babic

Hi Tom,

I dropped for the moment the following patches from Denis:

bootcount: i2c: Add bus switching to the I2C bootcount driver
bootcount: Configure length limit for I2C bootcount
board: ge: Store bootcount in EEPROM on PPD and Bx50v3

I used the same hack and PowerPC boards are built successfully on travis. Please pull from u-boot-imx, thanks !

The following changes since commit d117d8f19b0625f88309e47a8a32c2faa384dddc:

Merge branch 'master' of git://git.denx.de/u-boot-i2c (2018-12-13
09:36:55 -0500)

Quoted 9 lines

are available in the Git repository at:

git://www.denx.de/git/u-boot-imx.git tags/u-boot-imx-20190101

for you to fetch changes up to 57d2beb91d705bccdfee5e9e5fd267f5e363a100:

pico-imx7d: Increase the CONFIG_ENV_OFFSET size (2019-01-01 14:12:18
+0100)

tl;dr:
Applied to u-boot/master, thanks!

Slightly longer. I'm both not happy about taking something still this large so close to the end of the release and also at fault for it being so late. I started my holidays a week early so I didn't bisect the build failure until it was too late. That said, it's also a strong reminder of why everyone is encouraged to put their PR through travis. This PR includes a bunch of renaming that is important to get right
ASAP. It also has some small and important bug-fixes. So I'm applying
it.

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190101/8c0bceb3/attachment.sig>
#2 lore raw

Hi Tom,

Quoted 28 lines · Tom Rini
Quoted 16 lines · Stefano Babic

Hi Tom,

I dropped for the moment the following patches from Denis:

bootcount: i2c: Add bus switching to the I2C bootcount driver
bootcount: Configure length limit for I2C bootcount
board: ge: Store bootcount in EEPROM on PPD and Bx50v3

I used the same hack and PowerPC boards are built successfully on travis. Please pull from u-boot-imx, thanks !

The following changes since commit d117d8f19b0625f88309e47a8a32c2faa384dddc:

Merge branch 'master' of git://git.denx.de/u-boot-i2c (2018-12-13
09:36:55 -0500)

Quoted 9 lines

are available in the Git repository at:

git://www.denx.de/git/u-boot-imx.git tags/u-boot-imx-20190101

for you to fetch changes up to 57d2beb91d705bccdfee5e9e5fd267f5e363a100:

pico-imx7d: Increase the CONFIG_ENV_OFFSET size (2019-01-01 14:12:18
+0100)

Quoted 6 lines

tl;dr:
Applied to u-boot/master, thanks!

Slightly longer. I'm both not happy about taking something still this large so close to the end of the release and also at fault for it being so late.

Sorry for that.

Quoted 3 lines

I started my holidays a week early so I didn't bisect the
build failure until it was too late. That said, it's also a strong reminder of why everyone is encouraged to put their PR through travis.

Up now, a method for maintainer to check a PR was to use buildman. If buildman (at least for the maintained architecture) does not report errors, I sent my PR. I think I missed that a switch to Travis is now requested.

This also means that after a local test via buildman, each maintainer should wait until travis reports its result for all architecture. I mean, each maintainer triggers the same build and gets the result at least one day later. Should not be better if this is done just once when PR are merged into your tree and if ther eare some issues they are reported back to the corresponding maintainer ?

Best regards,
Stefano

Quoted 4 lines

This PR includes a bunch of renaming that is important to get right
ASAP. It also has some small and important bug-fixes. So I'm applying
it.

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
#3 lore raw
Quoted 40 lines · Stefano Babic

Hi Tom,

Quoted 28 lines · Tom Rini
Quoted 16 lines · Stefano Babic

Hi Tom,

I dropped for the moment the following patches from Denis:

bootcount: i2c: Add bus switching to the I2C bootcount driver
bootcount: Configure length limit for I2C bootcount
board: ge: Store bootcount in EEPROM on PPD and Bx50v3

I used the same hack and PowerPC boards are built successfully on travis. Please pull from u-boot-imx, thanks !

The following changes since commit d117d8f19b0625f88309e47a8a32c2faa384dddc:

Merge branch 'master' of git://git.denx.de/u-boot-i2c (2018-12-13
09:36:55 -0500)

Quoted 9 lines

are available in the Git repository at:

git://www.denx.de/git/u-boot-imx.git tags/u-boot-imx-20190101

for you to fetch changes up to 57d2beb91d705bccdfee5e9e5fd267f5e363a100:

pico-imx7d: Increase the CONFIG_ENV_OFFSET size (2019-01-01 14:12:18
+0100)

Quoted 6 lines

tl;dr:
Applied to u-boot/master, thanks!

Slightly longer. I'm both not happy about taking something still this large so close to the end of the release and also at fault for it being so late.

Sorry for that.

Quoted 8 lines
Quoted 3 lines

I started my holidays a week early so I didn't bisect the
build failure until it was too late. That said, it's also a strong reminder of why everyone is encouraged to put their PR through travis.

Up now, a method for maintainer to check a PR was to use buildman. If buildman (at least for the maintained architecture) does not report errors, I sent my PR. I think I missed that a switch to Travis is now requested.

So, yes, I have made a few requests (And, when travis has worse than usual network problems for a prolonged time, told people to forget about it if they don't want to fight it) for custodians to use travis. Buildman is great, and I do a run of that too on a different box (and I kicked my script to check better for bad exit codes) but most people don't have the time/patience/resources for a world build as well. Travis isn't as quick as I'd like, but is also free to use, which is a helpful trade-off.

Quoted 6 lines

This also means that after a local test via buildman, each maintainer should wait until travis reports its result for all architecture. I mean, each maintainer triggers the same build and gets the result at least one day later. Should not be better if this is done just once when PR are merged into your tree and if ther eare some issues they are reported back to the corresponding maintainer ?

I would run both simultaneously (travis will just re-start if you force-push a branch again). At the end of the day, I haven't made any requirements for what people need to test before they send me a PR. Travis is nice in that it builds the world and runs test.py on (just about) all of the targets we an do via QEMU. It also requires you to opt-in to using github and then travis-ci and I will not tell people they must sign up for a service they disagree with.

I also really appreciate it when custodians do a travis run and link it in their PR, and I still push it to a WIP branch and get my own travis run (and my own buildman world build and my own HW targets pushed through test.py).

At the end of the day, for me to push things to master, my local tests need to pass (and if/when they don't, I debug or try and help the author to debug failures) and travis needs to pass. There is a time cost to testing before sending to me and that may or may not be worse than the time cost when something fails.

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190109/cc04ab89/attachment.sig>
#4 lore raw
Quoted 50 lines · Tom Rini
Quoted 40 lines · Stefano Babic

Hi Tom,

Quoted 28 lines · Tom Rini
Quoted 16 lines · Stefano Babic

Hi Tom,

I dropped for the moment the following patches from Denis:

bootcount: i2c: Add bus switching to the I2C bootcount driver
bootcount: Configure length limit for I2C bootcount
board: ge: Store bootcount in EEPROM on PPD and Bx50v3

I used the same hack and PowerPC boards are built successfully on travis. Please pull from u-boot-imx, thanks !

The following changes since commit d117d8f19b0625f88309e47a8a32c2faa384dddc:

Merge branch 'master' of git://git.denx.de/u-boot-i2c (2018-12-13
09:36:55 -0500)

Quoted 9 lines

are available in the Git repository at:

git://www.denx.de/git/u-boot-imx.git tags/u-boot-imx-20190101

for you to fetch changes up to 57d2beb91d705bccdfee5e9e5fd267f5e363a100:

pico-imx7d: Increase the CONFIG_ENV_OFFSET size (2019-01-01 14:12:18
+0100)

Quoted 6 lines

tl;dr:
Applied to u-boot/master, thanks!

Slightly longer. I'm both not happy about taking something still this large so close to the end of the release and also at fault for it being so late.

Sorry for that.

Quoted 8 lines
Quoted 3 lines

I started my holidays a week early so I didn't bisect the
build failure until it was too late. That said, it's also a strong reminder of why everyone is encouraged to put their PR through travis.

Up now, a method for maintainer to check a PR was to use buildman. If buildman (at least for the maintained architecture) does not report errors, I sent my PR. I think I missed that a switch to Travis is now requested.

Quoted 6 lines

So, yes, I have made a few requests (And, when travis has worse than usual network problems for a prolonged time, told people to forget about it if they don't want to fight it) for custodians to use travis. Buildman is great, and I do a run of that too on a different box (and I kicked my script to check better for bad exit codes) but most people don't have the time/patience/resources for a world build as well.

This is correct - I just run ARM, not the whole world. It is also because I have often a "bitbake" running somewhere, and everything slows down.

Quoted 2 lines

Travis isn't as quick as I'd like, but is also free to use, which is a helpful trade-off.

ok, fine.

Quoted 16 lines
Quoted 7 lines

This also means that after a local test via buildman, each maintainer should wait until travis reports its result for all architecture. I mean, each maintainer triggers the same build and gets the result at least one day later. Should not be better if this is done just once when PR are merged into your tree and if ther eare some issues they are reported back to the corresponding maintainer ?

I would run both simultaneously (travis will just re-start if you force-push a branch again). At the end of the day, I haven't made any requirements for what people need to test before they send me a PR. Travis is nice in that it builds the world and runs test.py on (just about) all of the targets we an do via QEMU. It also requires you to opt-in to using github and then travis-ci and I will not tell people they must sign up for a service they disagree with.

Quoted 4 lines

I also really appreciate it when custodians do a travis run and link it in their PR, and I still push it to a WIP branch and get my own travis run (and my own buildman world build and my own HW targets pushed through test.py).

ok, understood, this will be the way I do since now.

Quoted 6 lines

At the end of the day, for me to push things to master, my local tests need to pass (and if/when they don't, I debug or try and help the author to debug failures) and travis needs to pass. There is a time cost to testing before sending to me and that may or may not be worse than the time cost when something fails.

Thanks for clarification,
Stefano

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================