amlogic: vim3: add support for dynamic PCIe enable
Subsystems (5)
v2 cover amlogic: vim3: add support for dynamic PCIe enable
The VIM3 on-board MCU can mux the PCIe/USB3.0 shared differential lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between an USB3.0 Type A connector and a M.2 Key M slot.
The PHY driving these differential lines is shared between the USB3.0 controller and the PCIe Controller, thus only a single controller can use it.
This serie adds a VIM3 specific board support and adds this dynamic switching right before booting Linux.
Changes since v1:
- add missing khadas-mcu.h
- add documentation to switch pcie on/off
Neil Armstrong (4):
ARM: dts: sync amlogic G12A/SM1 DT from Linux 5.9-rc1
board: amlogic: add a vim3 specific board support
configs: vim3: use the vim3 board support
board: amlogic: vim3: add support for dynamic PCIe enable
arch/arm/dts/meson-g12-common.dtsi | 55 ++++--- arch/arm/dts/meson-g12b-odroid-n2.dts | 136 +++++++++++++++++- arch/arm/dts/meson-khadas-vim3.dtsi | 26 +++- arch/arm/dts/meson-sm1-khadas-vim3l.dts | 92 ++++++++++++ arch/arm/dts/meson-sm1-odroid-c4.dts | 88 ++++++++++++ board/amlogic/vim3/MAINTAINERS | 9 ++ board/amlogic/vim3/Makefile | 6 + board/amlogic/vim3/khadas-mcu.h | 81 +++++++++++ board/amlogic/vim3/vim3.c | 136 ++++++++++++++++++ board/amlogic/w400/MAINTAINERS | 4 - configs/khadas-vim3_defconfig | 5 +- configs/khadas-vim3l_defconfig | 5 +- doc/board/amlogic/khadas-vim3.rst | 27 ++++ doc/board/amlogic/khadas-vim3l.rst | 27 ++++ include/dt-bindings/clock/g12a-clkc.h | 2 + .../dt-bindings/sound/meson-g12a-toacodec.h | 10 ++ 16 files changed, 679 insertions(+), 30 deletions(-) create mode 100644 board/amlogic/vim3/MAINTAINERS create mode 100644 board/amlogic/vim3/Makefile create mode 100644 board/amlogic/vim3/khadas-mcu.h create mode 100644 board/amlogic/vim3/vim3.c create mode 100644 include/dt-bindings/sound/meson-g12a-toacodec.h
Signature · 1 line
2.22.0
PATCH v2 1/4 ARM: dts: sync amlogic G12A/SM1 DT from Linux 5.9-rc1
This imports the G12A & SM1 SoC and boards DT changes from the Linux commit 9123e3a74ec7 ("Linux 5.9-rc1").
--- arch/arm/dts/meson-g12-common.dtsi | 55 ++++--- arch/arm/dts/meson-g12b-odroid-n2.dts | 136 +++++++++++++++++- arch/arm/dts/meson-khadas-vim3.dtsi | 26 +++- arch/arm/dts/meson-sm1-khadas-vim3l.dts | 92 ++++++++++++ arch/arm/dts/meson-sm1-odroid-c4.dts | 88 ++++++++++++ include/dt-bindings/clock/g12a-clkc.h | 2 + .../dt-bindings/sound/meson-g12a-toacodec.h | 10 ++ 7 files changed, 385 insertions(+), 24 deletions(-) create mode 100644 include/dt-bindings/sound/meson-g12a-toacodec.h
arch/arm/dts/meson-g12-common.dtsi +38 -17
@@ -52,6 +52,39 @@ secure-monitor = <&sm>; }; + gpu_opp_table: gpu-opp-table { + compatible = "operating-points-v2"; + + opp-124999998 { + opp-hz = /bits/ 64 <124999998>; + opp-microvolt = <800000>; + }; + opp-249999996 { + opp-hz = /bits/ 64 <249999996>; + opp-microvolt = <800000>; + }; + opp-285714281 { + opp-hz = /bits/ 64 <285714281>; + opp-microvolt = <800000>; + }; + opp-399999994 { + opp-hz = /bits/ 64 <399999994>; + opp-microvolt = <800000>; + }; + opp-499999992 { + opp-hz = /bits/ 64 <499999992>; + opp-microvolt = <800000>; + }; + opp-666666656 { + opp-hz = /bits/ 64 <666666656>; + opp-microvolt = <800000>; + }; + opp-799999987 { + opp-hz = /bits/ 64 <799999987>; + opp-microvolt = <800000>; + }; + }; + psci { compatible = "arm,psci-1.0"; method = "smc";
@@ -185,8 +218,10 @@ interrupt-names = "macirq"; clocks = <&clkc CLKID_ETH>, <&clkc CLKID_FCLK_DIV2>, - <&clkc CLKID_MPLL2>; - clock-names = "stmmaceth", "clkin0", "clkin1"; + <&clkc CLKID_MPLL2>, + <&clkc CLKID_FCLK_DIV2>; + clock-names = "stmmaceth", "clkin0", "clkin1", + "timing-adjustment"; rx-fifo-depth = <4096>; tx-fifo-depth = <2048>; status = "disabled";
@@ -2360,21 +2395,7 @@ interrupt-names = "job", "mmu", "gpu"; clocks = <&clkc CLKID_MALI>; resets = <&reset RESET_DVALIN_CAPB3>, <&reset RESET_DVALIN>; - - /* - * Mali clocking is provided by two identical clock paths - * MALI_0 and MALI_1 muxed to a single clock by a glitch - * free mux to safely change frequency while running. - */ - assigned-clocks = <&clkc CLKID_MALI_0_SEL>, - <&clkc CLKID_MALI_0>, - <&clkc CLKID_MALI>; /* Glitch free mux */ - assigned-clock-parents = <&clkc CLKID_FCLK_DIV2P5>, - <0>, /* Do Nothing */ - <&clkc CLKID_MALI_0>; - assigned-clock-rates = <0>, /* Do Nothing */ - <800000000>, - <0>; /* Do Nothing */ + operating-points-v2 = <&gpu_opp_table>; #cooling-cells = <2>; }; };
arch/arm/dts/meson-g12b-odroid-n2.dts +131 -5
198 lines not on this page · raw message
arch/arm/dts/meson-khadas-vim3.dtsi +24 -2
@@ -183,6 +183,23 @@ hdmi-phandle = <&hdmi_tx>; }; +&cpu_thermal { + trips { + cpu_active: cpu-active { + temperature = <80000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "active"; + }; + }; + + cooling-maps { + map { + trip = <&cpu_active>; + cooling-device = <&khadas_mcu THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; +}; + &ext_mdio { external_phy: ethernet-phy at 0 { /* Realtek RTL8211F (0x001cc916) */
@@ -222,6 +239,12 @@ pinctrl-0 = <&i2c_ao_sck_pins>, <&i2c_ao_sda_pins>; pinctrl-names = "default"; + khadas_mcu: system-controller at 18 { + compatible = "khadas,mcu"; + reg = <0x18>; + #cooling-cells = <2>; + }; + gpio_expander: gpio-controller at 20 { compatible = "ti,tca6408"; reg = <0x20>;
@@ -270,7 +293,6 @@ bus-width = <4>; cap-sd-highspeed; - sd-uhs-sdr50; max-frequency = <100000000>; non-removable;
@@ -337,7 +359,7 @@ pinctrl-0 = <&nor_pins>; pinctrl-names = "default"; - w25q32: spi-flash at 0 { + w25q128: spi-flash at 0 { #address-cells = <1>; #size-cells = <1>; compatible = "winbond,w25q128fw", "jedec,spi-nor";
arch/arm/dts/meson-sm1-khadas-vim3l.dts +92 -0
118 lines not on this page · raw message
arch/arm/dts/meson-sm1-odroid-c4.dts +88 -0
112 lines not on this page · raw message
include/dt-bindings/clock/g12a-clkc.h +2 -0
@@ -145,5 +145,7 @@#define CLKID_CPU3_CLK 255#define CLKID_SPICC0_SCLK 258#define CLKID_SPICC1_SCLK 261 +#define CLKID_NNA_AXI_CLK 264 +#define CLKID_NNA_CORE_CLK 267#endif /* __G12A_CLKC_H */
include/dt-bindings/sound/meson-g12a-toacodec.h new file +10 -0
@@ -0,0 +1,10 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +#ifndef __DT_MESON_G12A_TOACODEC_H +#define __DT_MESON_G12A_TOACODEC_H + +#define TOACODEC_IN_A 0 +#define TOACODEC_IN_B 1 +#define TOACODEC_IN_C 2 +#define TOACODEC_OUT 3 + +#endif /* __DT_MESON_G12A_TOACODEC_H */
Signature · 1 line
2.22.0
PATCH v2 2/4 board: amlogic: add a vim3 specific board support
In reply to Neil ArmstrongThe VIM3 will need a specific code to enable PCIe if enabled in the MCU, thus add a specific board support for VIM3 & VIM3L.
--- board/amlogic/vim3/MAINTAINERS | 9 +++++++++ board/amlogic/vim3/Makefile | 6 ++++++ board/amlogic/vim3/vim3.c | 20 ++++++++++++++++++++ board/amlogic/w400/MAINTAINERS | 4 ---- 4 files changed, 35 insertions(+), 4 deletions(-) create mode 100644 board/amlogic/vim3/MAINTAINERS create mode 100644 board/amlogic/vim3/Makefile create mode 100644 board/amlogic/vim3/vim3.c
board/amlogic/vim3/MAINTAINERS new file +9 -0
@@ -0,0 +1,9 @@ +VIM3 +M: Neil Armstrong <[email protected]> +S: Maintained +L: u-boot-amlogic at groups.io +F: board/amlogic/vim3/ +F: configs/khadas-vim3_defconfig +F: configs/khadas-vim3l_defconfig +F: doc/board/amlogic/khadas-vim3.rst +F: doc/board/amlogic/khadas-vim3l.rst
board/amlogic/vim3/Makefile new file +6 -0
@@ -0,0 +1,6 @@ +# SPDX-License-Identifier: GPL-2.0+ +# +# (C) Copyright 2020 BayLibre, SAS +# Author: Neil Armstrong <[email protected]> + +obj-y := vim3.o
board/amlogic/vim3/vim3.c new file +20 -0
@@ -0,0 +1,20 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* Copyright (C) 2020 BayLibre, SAS +* Author: Neil Armstrong <[email protected]> +*/ + +#include <common.h> +#include <dm.h> +#include <env_internal.h> +#include <init.h> +#include <net.h> +#include <asm/io.h> +#include <asm/arch/eth.h> + +int misc_init_r (void ) +{ +meson_eth_init (PHY_INTERFACE_MODE_RGMII ,0 ); + +return 0 ; +}
board/amlogic/w400/MAINTAINERS +0 -4
@@ -3,8 +3,4 @@ M: Neil Armstrong <[email protected]> S: Maintained L: u-boot-amlogic at groups.io F: board/amlogic/w400/ -F: configs/khadas-vim3_defconfig -F: configs/khadas-vim3l_defconfig F: doc/board/amlogic/w400.rst -F: doc/board/amlogic/khadas-vim3.rst -F: doc/board/amlogic/khadas-vim3l.rst
Signature · 1 line
2.22.0
PATCH v2 3/4 configs: vim3: use the vim3 board support
In reply to Neil ArmstrongUse the newly added VIM3 board support instead of the generic W400.
--- configs/khadas-vim3_defconfig | 2 +- configs/khadas-vim3l_defconfig | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-)
configs/khadas-vim3_defconfig +1 -1
@@ -1,5 +1,5 @@ CONFIG_ARM=y -CONFIG_SYS_BOARD="w400" +CONFIG_SYS_BOARD="vim3" CONFIG_ARCH_MESON=y CONFIG_SYS_TEXT_BASE=0x01000000 CONFIG_NR_DRAM_BANKS=1
configs/khadas-vim3l_defconfig +1 -1
@@ -1,5 +1,5 @@ CONFIG_ARM=y -CONFIG_SYS_BOARD="w400" +CONFIG_SYS_BOARD="vim3" CONFIG_ARCH_MESON=y CONFIG_SYS_TEXT_BASE=0x01000000 CONFIG_NR_DRAM_BANKS=1
Signature · 1 line
2.22.0
PATCH v2 4/4 board: amlogic: vim3: add support for dynamic PCIe enable
In reply to Neil ArmstrongThe VIM3 on-board MCU can mux the PCIe/USB3.0 shared differential lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between an USB3.0 Type A connector and a M.2 Key M slot.
The PHY driving these differential lines is shared between the USB3.0 controller and the PCIe Controller, thus only a single controller can use it.
This adds this dynamic switching right before booting Linux and the configuration steps in the boards documentation.
--- board/amlogic/vim3/khadas-mcu.h | 81 ++++++++++++++++++++ board/amlogic/vim3/vim3.c | 116 +++++++++++++++++++++++++++++ configs/khadas-vim3_defconfig | 3 + configs/khadas-vim3l_defconfig | 3 + doc/board/amlogic/khadas-vim3.rst | 27 +++++++ doc/board/amlogic/khadas-vim3l.rst | 27 +++++++ 6 files changed, 257 insertions(+) create mode 100644 board/amlogic/vim3/khadas-mcu.h
board/amlogic/vim3/khadas-mcu.h new file +81 -0
@@ -0,0 +1,81 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* +* Khadas System control Microcontroller Register map +* +* Copyright (C) 2020 BayLibre SAS +* +* Author(s): Neil Armstrong <[email protected]> +*/ + +#ifndef MFD_KHADAS_MCU_H +#define MFD_KHADAS_MCU_H + +#define KHADAS_MCU_PASSWD_VEN_0_REG 0x00/* RO */ +#define KHADAS_MCU_PASSWD_VEN_1_REG 0x01/* RO */ +#define KHADAS_MCU_PASSWD_VEN_2_REG 0x02/* RO */ +#define KHADAS_MCU_PASSWD_VEN_3_REG 0x03/* RO */ +#define KHADAS_MCU_PASSWD_VEN_4_REG 0x04/* RO */ +#define KHADAS_MCU_PASSWD_VEN_5_REG 0x05/* RO */ +#define KHADAS_MCU_MAC_0_REG 0x06/* RO */ +#define KHADAS_MCU_MAC_1_REG 0x07/* RO */ +#define KHADAS_MCU_MAC_2_REG 0x08/* RO */ +#define KHADAS_MCU_MAC_3_REG 0x09/* RO */ +#define KHADAS_MCU_MAC_4_REG 0x0a/* RO */ +#define KHADAS_MCU_MAC_5_REG 0x0b/* RO */ +#define KHADAS_MCU_USID_0_REG 0x0c/* RO */ +#define KHADAS_MCU_USID_1_REG 0x0d/* RO */ +#define KHADAS_MCU_USID_2_REG 0x0e/* RO */ +#define KHADAS_MCU_USID_3_REG 0x0f/* RO */ +#define KHADAS_MCU_USID_4_REG 0x10/* RO */ +#define KHADAS_MCU_USID_5_REG 0x11/* RO */ +#define KHADAS_MCU_VERSION_0_REG 0x12/* RO */ +#define KHADAS_MCU_VERSION_1_REG 0x13/* RO */ +#define KHADAS_MCU_DEVICE_NO_0_REG 0x14/* RO */ +#define KHADAS_MCU_DEVICE_NO_1_REG 0x15/* RO */ +#define KHADAS_MCU_FACTORY_TEST_REG 0x16/* R */ +#define KHADAS_MCU_BOOT_MODE_REG 0x20/* RW */ +#define KHADAS_MCU_BOOT_EN_WOL_REG 0x21/* RW */ +#define KHADAS_MCU_BOOT_EN_RTC_REG 0x22/* RW */ +#define KHADAS_MCU_BOOT_EN_EXP_REG 0x23/* RW */ +#define KHADAS_MCU_BOOT_EN_IR_REG 0x24/* RW */ +#define KHADAS_MCU_BOOT_EN_DCIN_REG 0x25/* RW */ +#define KHADAS_MCU_BOOT_EN_KEY_REG 0x26/* RW */ +#define KHADAS_MCU_KEY_MODE_REG 0x27/* RW */ +#define KHADAS_MCU_LED_MODE_ON_REG 0x28/* RW */ +#define KHADAS_MCU_LED_MODE_OFF_REG 0x29/* RW */ +#define KHADAS_MCU_SHUTDOWN_NORMAL_REG 0x2c/* RW */ +#define KHADAS_MCU_MAC_SWITCH_REG 0x2d/* RW */ +#define KHADAS_MCU_MCU_SLEEP_MODE_REG 0x2e/* RW */ +#define KHADAS_MCU_IR_CODE1_0_REG 0x2f/* RW */ +#define KHADAS_MCU_IR_CODE1_1_REG 0x30/* RW */ +#define KHADAS_MCU_IR_CODE1_2_REG 0x31/* RW */ +#define KHADAS_MCU_IR_CODE1_3_REG 0x32/* RW */ +#define KHADAS_MCU_USB_PCIE_SWITCH_REG 0x33/* RW */ +#define KHADAS_MCU_IR_CODE2_0_REG 0x34/* RW */ +#define KHADAS_MCU_IR_CODE2_1_REG 0x35/* RW */ +#define KHADAS_MCU_IR_CODE2_2_REG 0x36/* RW */ +#define KHADAS_MCU_IR_CODE2_3_REG 0x37/* RW */ +#define KHADAS_MCU_PASSWD_USER_0_REG 0x40/* RW */ +#define KHADAS_MCU_PASSWD_USER_1_REG 0x41/* RW */ +#define KHADAS_MCU_PASSWD_USER_2_REG 0x42/* RW */ +#define KHADAS_MCU_PASSWD_USER_3_REG 0x43/* RW */ +#define KHADAS_MCU_PASSWD_USER_4_REG 0x44/* RW */ +#define KHADAS_MCU_PASSWD_USER_5_REG 0x45/* RW */ +#define KHADAS_MCU_USER_DATA_0_REG 0x46/* RW 56 bytes */ +#define KHADAS_MCU_PWR_OFF_CMD_REG 0x80/* WO */ +#define KHADAS_MCU_PASSWD_START_REG 0x81/* WO */ +#define KHADAS_MCU_CHECK_VEN_PASSWD_REG 0x82/* WO */ +#define KHADAS_MCU_CHECK_USER_PASSWD_REG 0x83/* WO */ +#define KHADAS_MCU_SHUTDOWN_NORMAL_STATUS_REG 0x86/* RO */ +#define KHADAS_MCU_WOL_INIT_START_REG 0x87/* WO */ +#define KHADAS_MCU_CMD_FAN_STATUS_CTRL_REG 0x88/* WO */ + +enum { +KHADAS_BOARD_VIM1 =0x1 , +KHADAS_BOARD_VIM2 , +KHADAS_BOARD_VIM3 , +KHADAS_BOARD_EDGE =0x11 , +KHADAS_BOARD_EDGE_V , +}; + +#endif /* MFD_KHADAS_MCU_H */
board/amlogic/vim3/vim3.c +116 -0
122 lines not on this page · raw message
configs/khadas-vim3_defconfig +3 -0
@@ -17,6 +17,7 @@ CONFIG_MISC_INIT_R=y # CONFIG_CMD_BDI is not set # CONFIG_CMD_IMI is not set CONFIG_CMD_GPIO=y +CONFIG_CMD_I2C=y # CONFIG_CMD_LOADS is not set CONFIG_CMD_MMC=y CONFIG_CMD_SF_TEST=y
@@ -28,6 +29,8 @@ CONFIG_CMD_REGULATOR=y CONFIG_OF_CONTROL=y CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_NET_RANDOM_ETHADDR=y +CONFIG_DM_I2C=y +CONFIG_SYS_I2C_MESON=y CONFIG_DM_MMC=y CONFIG_MMC_MESON_GX=y CONFIG_MTD=y
configs/khadas-vim3l_defconfig +3 -0
@@ -17,6 +17,7 @@ CONFIG_MISC_INIT_R=y # CONFIG_CMD_BDI is not set # CONFIG_CMD_IMI is not set CONFIG_CMD_GPIO=y +CONFIG_CMD_I2C=y # CONFIG_CMD_LOADS is not set CONFIG_CMD_MMC=y CONFIG_CMD_SF_TEST=y
@@ -28,6 +29,8 @@ CONFIG_CMD_REGULATOR=y CONFIG_OF_CONTROL=y CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_NET_RANDOM_ETHADDR=y +CONFIG_DM_I2C=y +CONFIG_SYS_I2C_MESON=y CONFIG_DM_MMC=y CONFIG_MMC_MESON_GX=y CONFIG_MTD=y
doc/board/amlogic/khadas-vim3.rst +27 -0
@@ -18,6 +18,33 @@ Technology Co., Ltd. with the following specifications: Schematics are available on the manufacturer website. +PCIe Setup +---------- +The VIM3 on-board MCU can mux the PCIe/USB3.0 shared differential +lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between +an USB3.0 Type A connector and a M.2 Key M slot. +The PHY driving these differential lines is shared between +the USB3.0 controller and the PCIe Controller, thus only +a single controller can use it. + +To setup for PCIe, run the following commands from U-Boot: + +.. code-block:: none + + i2c dev i2c at 5000 + i2c mw 0x18 0x33 1 + +Then power-cycle the board. + +To set back to USB3.0, run the following commands from U-Boot: + +.. code-block:: none + + i2c dev i2c at 5000 + i2c mw 0x18 0x33 0 + +Then power-cycle the board. + U-Boot compilation ------------------
doc/board/amlogic/khadas-vim3l.rst +27 -0
@@ -18,6 +18,33 @@ Technology Co., Ltd. with the following specifications: Schematics are available on the manufacturer website. +PCIe Setup +---------- +The VIM3 on-board MCU can mux the PCIe/USB3.0 shared differential +lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between +an USB3.0 Type A connector and a M.2 Key M slot. +The PHY driving these differential lines is shared between +the USB3.0 controller and the PCIe Controller, thus only +a single controller can use it. + +To setup for PCIe, run the following commands from U-Boot: + +.. code-block:: none + + i2c dev i2c at 5000 + i2c mw 0x18 0x33 1 + +Then power-cycle the board. + +To set back to USB3.0, run the following commands from U-Boot: + +.. code-block:: none + + i2c dev i2c@5000 + i2c mw 0x18 0x33 0 + +Then power-cycle the board. + U-Boot compilation ------------------
Signature · 1 line
2.22.0
v2 cover amlogic: vim3: add support for dynamic PCIe enable
In reply to Neil ArmstrongQuoted 34 lines · Neil Armstrong
The VIM3 on-board MCU can mux the PCIe/USB3.0 shared differential lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between an USB3.0 Type A connector and a M.2 Key M slot.
The PHY driving these differential lines is shared between the USB3.0 controller and the PCIe Controller, thus only a single controller can use it.This serie adds a VIM3 specific board support and adds this dynamic switching right before booting Linux.
Changes since v1:
- add missingkhadas-mcu.h
- add documentation to switch pcie on/offNeil Armstrong (4):
ARM: dts: sync amlogic G12A/SM1 DT from Linux 5.9-rc1
board: amlogic: add a vim3 specific board support
configs: vim3: use the vim3 board support
board: amlogic: vim3: add support for dynamic PCIe enablearch/arm/dts/meson-g12-common.dtsi | 55 ++++--- arch/arm/dts/meson-g12b-odroid-n2.dts | 136 +++++++++++++++++- arch/arm/dts/meson-khadas-vim3.dtsi | 26 +++- arch/arm/dts/meson-sm1-khadas-vim3l.dts | 92 ++++++++++++ arch/arm/dts/meson-sm1-odroid-c4.dts | 88 ++++++++++++ board/amlogic/vim3/MAINTAINERS | 9 ++ board/amlogic/vim3/Makefile | 6 + board/amlogic/vim3/khadas-mcu.h | 81 +++++++++++ board/amlogic/vim3/vim3.c | 136 ++++++++++++++++++ board/amlogic/w400/MAINTAINERS | 4 - configs/khadas-vim3_defconfig | 5 +- configs/khadas-vim3l_defconfig | 5 +- doc/board/amlogic/khadas-vim3.rst | 27 ++++ doc/board/amlogic/khadas-vim3l.rst | 27 ++++
Quoted 9 lines
include/dt-bindings/clock/g12a-clkc.h | 2 + .../dt-bindings/sound/meson-g12a-toacodec.h | 10 ++ 16 files changed, 679 insertions(+), 30 deletions(-) create mode 100644 board/amlogic/vim3/MAINTAINERS create mode 100644 board/amlogic/vim3/Makefile create mode 100644 board/amlogic/vim3/khadas-mcu.h create mode 100644 board/amlogic/vim3/vim3.c create mode 100644 include/dt-bindings/sound/meson-g12a-toacodec.h
Applied to u-boot-amlogic-next