Skip to contentSkip to conversation

configs/warp7: Bump kernel and U-Boot versions

PATCH New Pierre-Jean Texier 3 participants 3 messages Jul 8, 2019 – Jul 14, 2019

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 configs/warp7: Bump kernel and U-Boot versions

Bump U-Boot to 2019.07 and kernel to version 5.1.16.

Also
- adjust the U-Boot binary name after DM conversion.
- add missing notes about DFU

---
Logs:
U-Boot 2019.07 (Jul 08 2019 - 21:48:39 +0200)

CPU:   Freescale i.MX7S rev1.2 800 MHz (running at 792 MHz)
CPU:   Extended Commercial temperature grade (-20C to 105C) at 41C
Reset cause: POR
Model: Warp i.MX7 Board
Board: WARP7 in secure mode OPTEE DRAM 0x9d000000-0xa0000000
DRAM:  464 MiB
PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x11
MMC:   FSL_SDHC: 1, FSL_SDHC: 0

=> run bootcmd
switch to partitions #0, OK
mmc0(part 0) is current device
switch to partitions #0, OK
mmc0(part 0) is current device
8188560 bytes read in 118 ms (66.2 MiB/s)
Booting from mmc ...
...
Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 5.1.16 (pjtexier at menoah)
 board/warp7/readme.txt  | 22 ++++++++++++++++++----
 configs/warp7_defconfig | 10 +++++-----
 2 files changed, 23 insertions(+), 9 deletions(-)
board/warp7/readme.txt +18 -4
index 47458e9..aff7a60 100644
@@ -20,7 +20,7 @@ You will find in output/images/ the following files:
   - rootfs.ext4
   - rootfs.tar
   - sdcard.img
-  - u-boot.imx
+  - u-boot-dtb.imx
   - zImage
 
 Flash the eMMC image
@@ -61,11 +61,11 @@ Connect a USB to serial adapter between the host PC and warp7 serial
 USB port, and also a USB cable between the OTG warp7 port and the host
 PC.
 
-Copy u-boot.imx to the imx_usb_loader folder.
+Copy u-boot-dtb.imx to the imx_usb_loader folder.
 
-Load u-boot.imx via USB:
+Load u-boot-dtb.imx via USB:
 
-$ sudo ./imx_usb u-boot.imx
+$ sudo ./imx_usb u-boot-dtb.imx
 
 Then U-Boot should start and its messages will appear in the console program.
 
@@ -75,6 +75,20 @@ Use the default environment variables:
 
 => env default -f -a
 => saveenv
+
+Run the DFU command:
+=> dfu 0 mmc 0
+
+Transfer u-boot-dtb.imx that will be flashed into the eMMC:
+
+$ sudo dfu-util -D u-boot-dtb.imx -a boot
+
+Then on the U-Boot prompt the following message should be seen after a
+successful upgrade:
+
+#DOWNLOAD ... OK
+Ctrl+C to exit ...
+
 => ums 0 mmc 0
 
 sudo dd if=output/images/sdcard.img of=/dev/<your-emmc-device>
configs/warp7_defconfig +5 -5
index 8acd730..9b10085 100644
@@ -3,8 +3,8 @@ BR2_arm=y
 BR2_cortex_a7=y
 BR2_ARM_FPU_NEON_VFPV4=y
 
-# Linux headers same as kernel, a 5.0 series
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_0=y
+# Linux headers same as kernel, a 5.1 series
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_1=y
 
 # system
 BR2_TARGET_GENERIC_GETTY_PORT="ttymxc0"
@@ -15,7 +15,7 @@ BR2_ROOTFS_OVERLAY="board/warp7/rootfs_overlay"
 # Kernel
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="5.0.9"
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="5.1.16"
 BR2_LINUX_KERNEL_DEFCONFIG="imx_v6_v7"
 BR2_LINUX_KERNEL_DTS_SUPPORT=y
 BR2_LINUX_KERNEL_INTREE_DTS_NAME="imx7s-warp"
@@ -25,8 +25,8 @@ BR2_LINUX_KERNEL_NEEDS_HOST_OPENSSL=y
 BR2_TARGET_UBOOT=y
 BR2_TARGET_UBOOT_BOARDNAME="warp7"
 BR2_TARGET_UBOOT_CUSTOM_VERSION=y
-BR2_TARGET_UBOOT_CUSTOM_VERSION_VALUE="2019.01"
-BR2_TARGET_UBOOT_FORMAT_IMX=y
+BR2_TARGET_UBOOT_CUSTOM_VERSION_VALUE="2019.07"
+BR2_TARGET_UBOOT_FORMAT_DTB_IMX=y
 
 # wifi firmware for brcm43430
 BR2_PACKAGE_LINUX_FIRMWARE=y
Signature · 1 line
2.7.4
#1 lore raw

PATCH 1/1 configs/warp7: Bump kernel and U-Boot versions

Hi Pierre-Jean

Le 08/07/2019 ? 22:11, Pierre-Jean Texier a ?crit?:

Quoted 111 lines

Bump U-Boot to 2019.07 and kernel to version 5.1.16.

Also
- adjust the U-Boot binary name after DM conversion.
- add missing notes about DFU

---
Logs:
U-Boot 2019.07 (Jul 08 2019 - 21:48:39 +0200)

CPU:   Freescale i.MX7S rev1.2 800 MHz (running at 792 MHz)
CPU:   Extended Commercial temperature grade (-20C to 105C) at 41C
Reset cause: POR
Model: Warp i.MX7 Board
Board: WARP7 in secure mode OPTEE DRAM 0x9d000000-0xa0000000
DRAM:  464 MiB
PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x11
MMC:   FSL_SDHC: 1, FSL_SDHC: 0

=> run bootcmd
switch to partitions #0, OK
mmc0(part 0) is current device
switch to partitions #0, OK
mmc0(part 0) is current device
8188560 bytes read in 118 ms (66.2 MiB/s)
Booting from mmc ...
...
Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 5.1.16 (pjtexier at menoah)
  board/warp7/readme.txt  | 22 ++++++++++++++++++----
  configs/warp7_defconfig | 10 +++++-----
  2 files changed, 23 insertions(+), 9 deletions(-)
board/warp7/readme.txt +18 -4
index 47458e9..aff7a60 100644
@@ -20,7 +20,7 @@ You will find in output/images/ the following files:
    - rootfs.ext4
    - rootfs.tar
    - sdcard.img
-  - u-boot.imx
+  - u-boot-dtb.imx
    - zImage
 
  Flash the eMMC image
@@ -61,11 +61,11 @@ Connect a USB to serial adapter between the host PC and warp7 serial
  USB port, and also a USB cable between the OTG warp7 port and the host
  PC.
 
-Copy u-boot.imx to the imx_usb_loader folder.
+Copy u-boot-dtb.imx to the imx_usb_loader folder.
 
-Load u-boot.imx via USB:
+Load u-boot-dtb.imx via USB:
 
-$ sudo ./imx_usb u-boot.imx
+$ sudo ./imx_usb u-boot-dtb.imx
 
  Then U-Boot should start and its messages will appear in the console program.
 
@@ -75,6 +75,20 @@ Use the default environment variables:
 
  => env default -f -a
  => saveenv
+
+Run the DFU command:
+=> dfu 0 mmc 0
+
+Transfer u-boot-dtb.imx that will be flashed into the eMMC:
+
+$ sudo dfu-util -D u-boot-dtb.imx -a boot
+
+Then on the U-Boot prompt the following message should be seen after a
+successful upgrade:
+
+#DOWNLOAD ... OK
+Ctrl+C to exit ...
+
  => ums 0 mmc 0
 
  sudo dd if=output/images/sdcard.img of=/dev/<your-emmc-device>
configs/warp7_defconfig +3 -3
index 8acd730..9b10085 100644
@@ -3,8 +3,8 @@ BR2_arm=y
  BR2_cortex_a7=y
  BR2_ARM_FPU_NEON_VFPV4=y
 
-# Linux headers same as kernel, a 5.0 series
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_0=y
+# Linux headers same as kernel, a 5.1 series
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_1=y
 
  # system
  BR2_TARGET_GENERIC_GETTY_PORT="ttymxc0"
@@ -15,7 +15,7 @@ BR2_ROOTFS_OVERLAY="board/warp7/rootfs_overlay"
  # Kernel
  BR2_LINUX_KERNEL=y
  BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="5.0.9"
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="5.1.16"
  BR2_LINUX_KERNEL_DEFCONFIG="imx_v6_v7"
  BR2_LINUX_KERNEL_DTS_SUPPORT=y
  BR2_LINUX_KERNEL_INTREE_DTS_NAME="imx7s-warp"

configs/warp7_defconfig BR2_LINUX_KERNEL_NEEDS_HOST_OPENSSL=y · line 32

Quoted 10 lines
configs/warp7_defconfig +2 -2
@@ -25,8 +25,8 @@ BR2_LINUX_KERNEL_NEEDS_HOST_OPENSSL=y
  BR2_TARGET_UBOOT=y
  BR2_TARGET_UBOOT_BOARDNAME="warp7"
  BR2_TARGET_UBOOT_CUSTOM_VERSION=y
-BR2_TARGET_UBOOT_CUSTOM_VERSION_VALUE="2019.01"
-BR2_TARGET_UBOOT_FORMAT_IMX=y
+BR2_TARGET_UBOOT_CUSTOM_VERSION_VALUE="2019.07"
+BR2_TARGET_UBOOT_FORMAT_DTB_IMX=y
 
  # wifi firmware for brcm43430
  BR2_PACKAGE_LINUX_FIRMWARE=y

it works for me

U-Boot 2019.07 (Jul 08 2019 - 23:35:25 +0200)

CPU:?? Freescale i.MX7S rev1.2 800 MHz (running at 792 MHz) CPU:?? Extended Commercial temperature grade (-20C to 105C) at 46C Reset cause: POR
Model: Warp i.MX7 Board
Board: WARP7 in secure mode OPTEE DRAM 0x9d000000-0xa0000000 DRAM:? 464 MiB
PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x11
MMC:?? FSL_SDHC: 1, FSL_SDHC: 0
Loading Environment from MMC... OK
In:??? serial at 30860000
Out:?? serial at 30860000
Err:?? serial at 30860000
SEC0: RNG instantiated
Net:?? usb_ether
Warning: usb_ether (eth0) using random MAC address - 4a:ec:76:9f:4e:28

Hit any key to stop autoboot:? 0
switch to partitions #0, OK
mmc0(part 0) is current device
switch to partitions #0, OK
mmc0(part 0) is current device
8188688 bytes read in 119 ms (65.6 MiB/s) Booting from mmc ...
26889 bytes read in 10 ms (2.6 MiB/s)
Kernel image @ 0x80800000 [ 0x000000 - 0x7cf310 ] ## Flattened Device Tree blob at 83000000
?? Booting using the fdt blob at 0x83000000
?? Using Device Tree in place at 83000000, end 83009908

Starting kernel ...

Best Regards,

Joris Offouga

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.busybox.net/pipermail/buildroot/attachments/20190708/9be20de2/attachment.html>

#2 lore raw

PATCH 1/1 configs/warp7: Bump kernel and U-Boot versions

In reply to Pierre-Jean Texier
Quoted 8 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line

"Pierre-Jean" == Pierre-Jean Texier <[email protected]> writes:

Bump U-Boot to 2019.07 and kernel to version 5.1.16. Also
- adjust the U-Boot binary name after DM conversion.
- add missing notes about DFU

Committed, thanks.

Signature · 1 line
Bye, Peter Korsgaard