tty: TX helpers
Subsystems (17)
Jiri Slaby (SUSE)
maintainerv5 cover tty: TX helpers
This series introduces uart_port_tx() + uart_port_tx_limited() TX helpers. See PATCH 1/3 for the details.
The preparatory cleanups were already merged, so only the helpers above and the switch: first, to uart_port_tx() in 2/3 and then uart_port_tx_limited() in 3/3.
I know it's pre-rc1 time now. But there is no rush. Maybe non-maintainers can take time to review now ;).
Jiri Slaby (SUSE) (3):
tty: serial: introduce transmit helpers
tty: serial: use uart_port_tx() helper
tty: serial: use uart_port_tx_limited()
Documentation/driver-api/serial/driver.rst | 3 + drivers/tty/serial/21285.c | 32 ++------- drivers/tty/serial/altera_jtaguart.c | 36 ++-------- drivers/tty/serial/altera_uart.c | 29 ++------ drivers/tty/serial/amba-pl010.c | 32 ++------- drivers/tty/serial/apbuart.c | 34 ++------- drivers/tty/serial/atmel_serial.c | 28 ++------ drivers/tty/serial/bcm63xx_uart.c | 47 +++---------- drivers/tty/serial/fsl_lpuart.c | 30 ++------ drivers/tty/serial/lantiq.c | 36 ++-------- drivers/tty/serial/lpc32xx_hs.c | 33 ++------- drivers/tty/serial/mcf.c | 34 +++------ drivers/tty/serial/mpc52xx_uart.c | 39 ++--------- drivers/tty/serial/mps2-uart.c | 26 ++----- drivers/tty/serial/mux.c | 45 ++++-------- drivers/tty/serial/mvebu-uart.c | 38 ++-------- drivers/tty/serial/mxs-auart.c | 32 +++------ drivers/tty/serial/omap-serial.c | 32 ++------- drivers/tty/serial/owl-uart.c | 32 ++------- drivers/tty/serial/pxa.c | 33 ++------- drivers/tty/serial/rp2.c | 31 ++------- drivers/tty/serial/sa1100.c | 34 ++------- drivers/tty/serial/serial_txx9.c | 32 ++------- drivers/tty/serial/sifive.c | 31 ++------- drivers/tty/serial/sprd_serial.c | 33 ++------- drivers/tty/serial/st-asc.c | 48 ++----------- drivers/tty/serial/vt8500_serial.c | 30 ++------ include/linux/serial_core.h | 80 ++++++++++++++++++++++ 28 files changed, 228 insertions(+), 742 deletions(-)
Signature · 1 line
2.37.3
Jiri Slaby (SUSE)
maintainerPATCH v5 1/3 tty: serial: introduce transmit helpers
Many serial drivers do the same thing:
* send x_char if set
* keep sending from the xmit circular buffer until either
- the loop reaches the end of the xmit buffer
- TX is stopped
- HW fifo is full
* check for pending characters and:
- wake up tty writers to fill for more data into xmit buffer
- stop TX if there is nothing in the xmit buffer
The only differences are:
* how to write the character to the HW fifo
* the check of the end condition:
- is the HW fifo full?
- is limit of the written characters reached?
So unify the above into two helpers:
* uart_port_tx_limited() -- it performs the above taking the written characters limit into account, and
* uart_port_tx() -- the same as above, except it only checks the HW readiness, not the characters limit.
The HW specific operations (as stated as "differences" above) are passed as arguments to the macros. They are:
* tx_ready -- returns true if HW can accept more data.
* put_char -- write a character to the device.
* tx_done -- when the write loop is done, perform arbitrary action before potential invocation of ops->stop_tx() happens.
Note that the above are macros. This means the code is generated in place and the above 3 arguments are "inlined". I.e. no added penalty by generating call instructions for every single character. Nor any indirect calls. (As in some previous versions of this patchset.)
---
Notes:
[v4] switch from helper generators to helpers similar to wait_event()
[Arnd]
Documentation/driver-api/serial/driver.rst | 3 + include/linux/serial_core.h | 80 ++++++++++++++++++++++ 2 files changed, 83 insertions(+)
Documentation/driver-api/serial/driver.rst +3 -0
@@ -78,6 +78,9 @@ Other functions uart_get_lsr_info uart_handle_dcd_change uart_handle_cts_change uart_try_toggle_sysrq uart_get_console +.. kernel-doc:: include/linux/serial_core.h + :identifiers: uart_port_tx_limited uart_port_tx + Other notes -----------
include/linux/serial_core.h +80 -0
86 lines not on this page · raw message
Signature · 1 line
2.37.3
Jiri Slaby (SUSE)
maintainerPATCH v5 2/3 tty: serial: use uart_port_tx() helper
In reply to Jiri Slaby (SUSE)uart_port_tx() is a new helper to send characters to the device. Use it in these drivers.
---
Notes:
[v5] use bool pending in mcf_tx_chars() too [Ilpo]
[v4] switch from DEFINE_UART_PORT_TX_HELPER() (helper generator) to
uart_port_tx() (akin to wait_event())
[v3] remove stray \n removal (Ilpo)
drivers/tty/serial/altera_uart.c | 29 ++++------------------ drivers/tty/serial/atmel_serial.c | 28 +++++---------------- drivers/tty/serial/fsl_lpuart.c | 30 ++++------------------- drivers/tty/serial/lantiq.c | 36 +++------------------------ drivers/tty/serial/lpc32xx_hs.c | 33 +++---------------------- drivers/tty/serial/mcf.c | 34 ++++++-------------------- drivers/tty/serial/mpc52xx_uart.c | 39 +++--------------------------- drivers/tty/serial/mps2-uart.c | 26 +++----------------- drivers/tty/serial/mxs-auart.c | 32 ++++++------------------ drivers/tty/serial/owl-uart.c | 32 +++--------------------- drivers/tty/serial/sa1100.c | 34 +++----------------------- drivers/tty/serial/vt8500_serial.c | 30 +++-------------------- 12 files changed, 60 insertions(+), 323 deletions(-)
drivers/tty/serial/altera_uart.c +5 -24
@@ -247,31 +247,12 @@ static void altera_uart_rx_chars(struct uart_port *port)static void altera_uart_tx_chars (struct uart_port *port) { -struct circ_buf *xmit = &port->state->xmit; - -if (port->x_char) { -/* Send special char - probably flow control */ -altera_uart_writel (port, port->x_char,ALTERA_UART_TXDATA_REG ); - port->x_char =0 ; - port->icount.tx++; -return ; - } - -while (altera_uart_readl (port,ALTERA_UART_STATUS_REG ) & -ALTERA_UART_STATUS_TRDY_MSK ) { -if (xmit->head == xmit->tail) -break ; -altera_uart_writel (port, xmit->buf[xmit->tail], -ALTERA_UART_TXDATA_REG ); - xmit->tail = (xmit->tail +1 ) & (UART_XMIT_SIZE -1 ); - port->icount.tx++; - } - -if (uart_circ_chars_pending (xmit) <WAKEUP_CHARS ) -uart_write_wakeup (port); +u8 ch; -if (uart_circ_empty (xmit)) -altera_uart_stop_tx (port); +uart_port_tx (port, ch, +altera_uart_readl (port,ALTERA_UART_STATUS_REG ) & +ALTERA_UART_STATUS_TRDY_MSK , +altera_uart_writel (port, ch,ALTERA_UART_TXDATA_REG )); }static irqreturn_t altera_uart_interrupt (int irq,void *data)
drivers/tty/serial/atmel_serial.c +6 -22
@@ -824,30 +824,14 @@ static void atmel_rx_chars(struct uart_port *port)*/ static void atmel_tx_chars (struct uart_port *port) { -struct circ_buf *xmit = &port->state->xmit;struct atmel_uart_port *atmel_port =to_atmel_uart_port (port); +bool pending; +u8 ch; -if (port->x_char && - (atmel_uart_readl (port,ATMEL_US_CSR ) &ATMEL_US_TXRDY )) { -atmel_uart_write_char (port, port->x_char); - port->icount.tx++; - port->x_char =0 ; - } -if (uart_circ_empty (xmit) ||uart_tx_stopped (port)) -return ; - -while (atmel_uart_readl (port,ATMEL_US_CSR ) &ATMEL_US_TXRDY ) { -atmel_uart_write_char (port, xmit->buf[xmit->tail]); - xmit->tail = (xmit->tail +1 ) & (UART_XMIT_SIZE -1 ); - port->icount.tx++; -if (uart_circ_empty (xmit)) -break ; - } - -if (uart_circ_chars_pending (xmit) <WAKEUP_CHARS ) -uart_write_wakeup (port); - -if (!uart_circ_empty (xmit)) { + pending =uart_port_tx (port, ch, +atmel_uart_readl (port,ATMEL_US_CSR ) &ATMEL_US_TXRDY , +atmel_uart_write_char (port, ch)); +if (pending) {/* we still have characters to transmit, so we should continue * transmitting them when TX is ready, regardless of * mode or duplexity
drivers/tty/serial/fsl_lpuart.c +5 -25
@@ -742,32 +742,12 @@ static int lpuart32_poll_get_char(struct uart_port *port)static inline void lpuart_transmit_buffer (struct lpuart_port *sport) { -struct circ_buf *xmit = &sport->port.state->xmit; - -if (sport->port.x_char) { -writeb (sport->port.x_char, sport->port.membase +UARTDR ); - sport->port.icount.tx++; - sport->port.x_char =0 ; -return ; - } - -if (lpuart_stopped_or_empty (&sport->port)) { -lpuart_stop_tx (&sport->port); -return ; - } - -while (!uart_circ_empty (xmit) && - (readb (sport->port.membase +UARTTCFIFO ) < sport->txfifo_size)) { -writeb (xmit->buf[xmit->tail], sport->port.membase +UARTDR ); - xmit->tail = (xmit->tail +1 ) & (UART_XMIT_SIZE -1 ); - sport->port.icount.tx++; - } - -if (uart_circ_chars_pending (xmit) <WAKEUP_CHARS ) -uart_write_wakeup (&sport->port); +struct uart_port *port = &sport->port; +u8 ch; -if (uart_circ_empty (xmit)) -lpuart_stop_tx (&sport->port); +uart_port_tx (port, ch, +readb (port->membase +UARTTCFIFO ) < sport->txfifo_size, +writeb (ch, port->membase +UARTDR )); }static inline void lpuart32_transmit_buffer (struct lpuart_port *sport)
drivers/tty/serial/lantiq.c +4 -32
@@ -95,7 +95,6 @@#define ASCFSTAT_TXFFLMASK 0x3F00#define ASCFSTAT_TXFREEMASK 0x3F000000 -static void lqasc_tx_chars (struct uart_port *port);static struct ltq_uart_port *lqasc_port[MAXPORTS ];static struct uart_driver lqasc_reg;
@@ -151,9 +150,12 @@ lqasc_start_tx(struct uart_port *port) {unsigned long flags;struct ltq_uart_port *ltq_port =to_ltq_uart_port (port); +u8 ch;spin_lock_irqsave (<q_port->lock, flags); -lqasc_tx_chars (port); +uart_port_tx (port, ch, +lqasc_tx_ready (port), +writeb (ch, port->membase +LTQ_ASC_TBUF ));spin_unlock_irqrestore (<q_port->lock, flags);return ; }
@@ -226,36 +228,6 @@ lqasc_rx_chars(struct uart_port *port)return 0 ; } -static void -lqasc_tx_chars (struct uart_port *port) -{ -struct circ_buf *xmit = &port->state->xmit; -if (uart_tx_stopped (port)) { -lqasc_stop_tx (port); -return ; - } - -while (lqasc_tx_ready (port)) { -if (port->x_char) { -writeb (port->x_char, port->membase +LTQ_ASC_TBUF ); - port->icount.tx++; - port->x_char =0 ; -continue ; - } - -if (uart_circ_empty (xmit)) -break ; - -writeb (port->state->xmit.buf[port->state->xmit.tail], - port->membase +LTQ_ASC_TBUF ); - xmit->tail = (xmit->tail +1 ) & (UART_XMIT_SIZE -1 ); - port->icount.tx++; - } - -if (uart_circ_chars_pending (xmit) <WAKEUP_CHARS ) -uart_write_wakeup (port); -} -static irqreturn_t lqasc_tx_int (int irq,void *_port) {
drivers/tty/serial/lpc32xx_hs.c +4 -29
@@ -276,8 +276,6 @@ static void __serial_lpc32xx_rx(struct uart_port *port)tty_flip_buffer_push (tport); } -static void serial_lpc32xx_stop_tx (struct uart_port *port); -static bool serial_lpc32xx_tx_ready (struct uart_port *port) {u32 level =readl (LPC32XX_HSUART_LEVEL (port->membase));
@@ -287,34 +285,11 @@ static bool serial_lpc32xx_tx_ready(struct uart_port *port)static void __serial_lpc32xx_tx (struct uart_port *port) { -struct circ_buf *xmit = &port->state->xmit; - -if (port->x_char) { -writel ((u32 )port->x_char,LPC32XX_HSUART_FIFO (port->membase)); - port->icount.tx++; - port->x_char =0 ; -return ; - } - -if (uart_circ_empty (xmit) ||uart_tx_stopped (port)) - goto exit_tx; - -/* Transfer data */ -while (serial_lpc32xx_tx_ready (port)) { -writel ((u32 ) xmit->buf[xmit->tail], -LPC32XX_HSUART_FIFO (port->membase)); - xmit->tail = (xmit->tail +1 ) & (UART_XMIT_SIZE -1 ); - port->icount.tx++; -if (uart_circ_empty (xmit)) -break ; - } - -if (uart_circ_chars_pending (xmit) <WAKEUP_CHARS ) -uart_write_wakeup (port); +u8 ch; -exit_tx: -if (uart_circ_empty (xmit)) -serial_lpc32xx_stop_tx (port); +uart_port_tx (port, ch, +serial_lpc32xx_tx_ready (port), +writel (ch,LPC32XX_HSUART_FIFO (port->membase))); }static irqreturn_t serial_lpc32xx_interrupt (int irq,void *dev_id)
drivers/tty/serial/mcf.c +8 -26
@@ -327,34 +327,16 @@ static void mcf_rx_chars(struct mcf_uart *pp)static void mcf_tx_chars (struct mcf_uart *pp) {struct uart_port *port = &pp->port; -struct circ_buf *xmit = &port->state->xmit; - -if (port->x_char) { -/* Send special char - probably flow control */ -writeb (port->x_char, port->membase +MCFUART_UTB ); - port->x_char =0 ; - port->icount.tx++; -return ; - } - -while (readb (port->membase +MCFUART_USR ) &MCFUART_USR_TXREADY ) { -if (uart_circ_empty (xmit)) -break ; -writeb (xmit->buf[xmit->tail], port->membase +MCFUART_UTB ); - xmit->tail = (xmit->tail +1 ) & (UART_XMIT_SIZE -1 ); - port->icount.tx++; - } +bool pending; +u8 ch; -if (uart_circ_chars_pending (xmit) <WAKEUP_CHARS ) -uart_write_wakeup (port); + pending =uart_port_tx (port, ch, +readb (port->membase +MCFUART_USR ) &MCFUART_USR_TXREADY , +writeb (ch, port->membase +MCFUART_UTB )); -if (uart_circ_empty (xmit)) { -mcf_stop_tx (port); -/* Disable TX to negate RTS automatically */ -if (port->rs485.flags &SER_RS485_ENABLED ) -writeb (MCFUART_UCR_TXDISABLE , - port->membase +MCFUART_UCR ); - } +/* Disable TX to negate RTS automatically */ +if (!pending && (port->rs485.flags &SER_RS485_ENABLED )) +writeb (MCFUART_UCR_TXDISABLE , port->membase +MCFUART_UCR ); }/****************************************************************************/
drivers/tty/serial/mpc52xx_uart.c +4 -35
@@ -1428,42 +1428,11 @@ mpc52xx_uart_int_rx_chars(struct uart_port *port)static inline bool mpc52xx_uart_int_tx_chars (struct uart_port *port) { -struct circ_buf *xmit = &port->state->xmit; - -/* Process out of band chars */ -if (port->x_char) { - psc_ops->write_char (port, port->x_char); - port->icount.tx++; - port->x_char =0 ; -return true; - } - -/* Nothing to do ? */ -if (uart_circ_empty (xmit) ||uart_tx_stopped (port)) { -mpc52xx_uart_stop_tx (port); -return false; - } - -/* Send chars */ -while (psc_ops->raw_tx_rdy (port)) { - psc_ops->write_char (port, xmit->buf[xmit->tail]); - xmit->tail = (xmit->tail +1 ) & (UART_XMIT_SIZE -1 ); - port->icount.tx++; -if (uart_circ_empty (xmit)) -break ; - } - -/* Wake up */ -if (uart_circ_chars_pending (xmit) <WAKEUP_CHARS ) -uart_write_wakeup (port); - -/* Maybe we're done after all */ -if (uart_circ_empty (xmit)) { -mpc52xx_uart_stop_tx (port); -return false; - } +u8 ch; -return true; +return uart_port_tx (port, ch, + psc_ops->raw_tx_rdy (port), + psc_ops->write_char (port, ch)); } static irqreturn_t
drivers/tty/serial/mps2-uart.c +4 -22
@@ -129,29 +129,11 @@ static void mps2_uart_stop_tx(struct uart_port *port)static void mps2_uart_tx_chars (struct uart_port *port) { -struct circ_buf *xmit = &port->state->xmit; - -while (!(mps2_uart_read8 (port, UARTn_STATE) & UARTn_STATE_TX_FULL)) { -if (port->x_char) { -mps2_uart_write8 (port, port->x_char, UARTn_DATA); - port->x_char =0 ; - port->icount.tx++; -continue ; - } - -if (uart_circ_empty (xmit) ||uart_tx_stopped (port)) -break ; - -mps2_uart_write8 (port, xmit->buf[xmit->tail], UARTn_DATA); - xmit->tail = (xmit->tail +1 ) %UART_XMIT_SIZE ; - port->icount.tx++; - } - -if (uart_circ_chars_pending (xmit) <WAKEUP_CHARS ) -uart_write_wakeup (port); +u8 ch; -if (uart_circ_empty (xmit)) -mps2_uart_stop_tx (port); +uart_port_tx (port, ch, +mps2_uart_tx_empty (port), +mps2_uart_write8 (port, ch, UARTn_DATA)); }static void mps2_uart_start_tx (struct uart_port *port)
drivers/tty/serial/mxs-auart.c +8 -24
@@ -569,6 +569,8 @@ static int mxs_auart_dma_tx(struct mxs_auart_port *s, int size)static void mxs_auart_tx_chars (struct mxs_auart_port *s) {struct circ_buf *xmit = &s->port.state->xmit; +bool pending; +u8 ch;if (auart_dma_enabled (s)) {u32 i =0 ;
@@ -603,31 +605,13 @@ static void mxs_auart_tx_chars(struct mxs_auart_port *s)return ; } - -while (!(mxs_read (s,REG_STAT ) &AUART_STAT_TXFF )) { -if (s->port.x_char) { - s->port.icount.tx++; -mxs_write (s->port.x_char, s,REG_DATA ); - s->port.x_char =0 ; -continue ; - } -if (!uart_circ_empty (xmit) && !uart_tx_stopped (&s->port)) { - s->port.icount.tx++; -mxs_write (xmit->buf[xmit->tail], s,REG_DATA ); - xmit->tail = (xmit->tail +1 ) & (UART_XMIT_SIZE -1 ); - }else -break ; - } -if (uart_circ_chars_pending (xmit) <WAKEUP_CHARS ) -uart_write_wakeup (&s->port); - -if (uart_circ_empty (&(s->port.state->xmit))) -mxs_clr (AUART_INTR_TXIEN , s,REG_INTR ); -else + pending =uart_port_tx (&s->port, ch, + !(mxs_read (s,REG_STAT ) &AUART_STAT_TXFF ), +mxs_write (ch, s,REG_DATA )); +if (pending)mxs_set (AUART_INTR_TXIEN , s,REG_INTR ); - -if (uart_tx_stopped (&s->port)) -mxs_auart_stop_tx (&s->port); +else +mxs_clr (AUART_INTR_TXIEN , s,REG_INTR ); }static void mxs_auart_rx_char (struct mxs_auart_port *s)
drivers/tty/serial/owl-uart.c +4 -28
@@ -181,35 +181,11 @@ static void owl_uart_start_tx(struct uart_port *port)static void owl_uart_send_chars (struct uart_port *port) { -struct circ_buf *xmit = &port->state->xmit; -unsigned int ch; - -if (port->x_char) { -while (!(owl_uart_read (port,OWL_UART_STAT ) &OWL_UART_STAT_TFFU )) -cpu_relax (); -owl_uart_write (port, port->x_char,OWL_UART_TXDAT ); - port->icount.tx++; - port->x_char =0 ; - } - -if (uart_tx_stopped (port)) -return ; - -while (!(owl_uart_read (port,OWL_UART_STAT ) &OWL_UART_STAT_TFFU )) { -if (uart_circ_empty (xmit)) -break ; +u8 ch; - ch = xmit->buf[xmit->tail]; -owl_uart_write (port, ch,OWL_UART_TXDAT ); - xmit->tail = (xmit->tail +1 ) & (UART_XMIT_SIZE -1 ); - port->icount.tx++; - } - -if (uart_circ_chars_pending (xmit) <WAKEUP_CHARS ) -uart_write_wakeup (port); - -if (uart_circ_empty (xmit)) -owl_uart_stop_tx (port); +uart_port_tx (port, ch, + !(owl_uart_read (port,OWL_UART_STAT ) &OWL_UART_STAT_TFFU ), +owl_uart_write (port, ch,OWL_UART_TXDAT )); }static void owl_uart_receive_chars (struct uart_port *port)
drivers/tty/serial/sa1100.c +4 -30
@@ -228,14 +228,7 @@ sa1100_rx_chars(struct sa1100_port *sport)static void sa1100_tx_chars (struct sa1100_port *sport) { -struct circ_buf *xmit = &sport->port.state->xmit; - -if (sport->port.x_char) { -UART_PUT_CHAR (sport, sport->port.x_char); - sport->port.icount.tx++; - sport->port.x_char =0 ; -return ; - } +u8 ch;/* * Check the modem control lines before
@@ -243,28 +236,9 @@ static void sa1100_tx_chars(struct sa1100_port *sport)*/ sa1100_mctrl_check (sport); -if (uart_circ_empty (xmit) ||uart_tx_stopped (&sport->port)) { -sa1100_stop_tx (&sport->port); -return ; - } - -/* -* Tried using FIFO (not checking TNF) for fifo fill: -* still had the '4 bytes repeated' problem. -*/ -while (UART_GET_UTSR1 (sport) &UTSR1_TNF ) { -UART_PUT_CHAR (sport, xmit->buf[xmit->tail]); - xmit->tail = (xmit->tail +1 ) & (UART_XMIT_SIZE -1 ); - sport->port.icount.tx++; -if (uart_circ_empty (xmit)) -break ; - } - -if (uart_circ_chars_pending (xmit) <WAKEUP_CHARS ) -uart_write_wakeup (&sport->port); - -if (uart_circ_empty (xmit)) -sa1100_stop_tx (&sport->port); +uart_port_tx (&sport->port, ch, +UART_GET_UTSR1 (sport) &UTSR1_TNF , +UART_PUT_CHAR (sport, ch)); }static irqreturn_t sa1100_int (int irq,void *dev_id)
drivers/tty/serial/vt8500_serial.c +4 -26
@@ -196,33 +196,11 @@ static unsigned int vt8500_tx_empty(struct uart_port *port)static void handle_tx (struct uart_port *port) { -struct circ_buf *xmit = &port->state->xmit; +u8 ch; -if (port->x_char) { -writeb (port->x_char, port->membase +VT8500_TXFIFO ); - port->icount.tx++; - port->x_char =0 ; - } -if (uart_circ_empty (xmit) ||uart_tx_stopped (port)) { -vt8500_stop_tx (port); -return ; - } - -while (vt8500_tx_empty (port)) { -if (uart_circ_empty (xmit)) -break ; - -writeb (xmit->buf[xmit->tail], port->membase +VT8500_TXFIFO ); - - xmit->tail = (xmit->tail +1 ) & (UART_XMIT_SIZE -1 ); - port->icount.tx++; - } - -if (uart_circ_chars_pending (xmit) <WAKEUP_CHARS ) -uart_write_wakeup (port); - -if (uart_circ_empty (xmit)) -vt8500_stop_tx (port); +uart_port_tx (port, ch, +vt8500_tx_empty (port), +writeb (ch, port->membase +VT8500_TXFIFO )); }static void vt8500_start_tx (struct uart_port *port)
Signature · 1 line
2.37.3
Re: [PATCH v5 2/3] tty: serial: use uart_port_tx() helper
From: "Jiri Slaby (SUSE)" <[email protected]>
Hi Jiri,
Quoted 31 lines
drivers/tty/serial/atmel_serial.c +2
-19@@ -824,30 +824,14 @@ static void atmel_rx_chars(struct uart_port *port)*/ static void atmel_tx_chars (struct uart_port *port) { -struct circ_buf *xmit = &port->state->xmit;struct atmel_uart_port *atmel_port =to_atmel_uart_port (port); +bool pending; +u8 ch; -if (port->x_char && - (atmel_uart_readl (port,ATMEL_US_CSR ) &ATMEL_US_TXRDY )) { -atmel_uart_write_char (port, port->x_char); - port->icount.tx++; - port->x_char =0 ; - } -if (uart_circ_empty (xmit) ||uart_tx_stopped (port)) -return ; - -while (atmel_uart_readl (port,ATMEL_US_CSR ) &ATMEL_US_TXRDY ) { -atmel_uart_write_char (port, xmit->buf[xmit->tail]); - xmit->tail = (xmit->tail +1 ) & (UART_XMIT_SIZE -1 ); - port->icount.tx++; -if (uart_circ_empty (xmit)) -break ; - } - -if (uart_circ_chars_pending (xmit) <WAKEUP_CHARS )
drivers/tty/serial/atmel_serial.c static void atmel_rx_chars(struct uart_port *port) · line 837
Quoted 10 lines
drivers/tty/serial/atmel_serial.c +4
-3-uart_write_wakeup (port); - -if (!uart_circ_empty (xmit)) { + pending =uart_port_tx (port, ch, +atmel_uart_readl (port,ATMEL_US_CSR ) &ATMEL_US_TXRDY , +atmel_uart_write_char (port, ch)); +if (pending) {/* we still have characters to transmit, so we should continue * transmitting them when TX is ready, regardless of * mode or duplexity
This will break serial output for the userspace on my board (arch/arm/boot/dts/lan966x-kontron-kswitch-d10-mmt*dts). The uart_port_tx() helper will call __port->ops->stop_tx(__port) if uart_circ_chars_pending() returns 0. But the code above, doesn't do that. In fact, removing the stop_tx() call in the helper macro, will fix the console output.
Any ideas how to fix that?
-michael
Jiri Slaby
maintainerRe: [PATCH v5 2/3] tty: serial: use uart_port_tx() helper
Hi,
Quoted 7 lines · Michael Walle
This will break serial output for the userspace on my board (
arch/arm/boot/dts/lan966x-kontron-kswitch-d10-mmt*dts). Theuart_port_tx()helper will call__port->ops->stop_tx(__port)ifuart_circ_chars_pending()returns 0. But the code above, doesn't do that. In fact, removing thestop_tx()call in the helper macro, will fix the console output.Any ideas how to fix that?
Hm, so ATMEL_US_TXRDY is removed from tx_done_mask in stop_tx, but not added back in start_tx. So the tx interrupt is never handled (the tx tasklet is not scheduled to send the queue chars) in atmel_handle_transmit().
Any chance, the below fixes it?
drivers/tty/serial/atmel_serial.c +2 -0
@@ -596,6 +596,8 @@ static void atmel_start_tx(struct uart_port *port)/* re-enable PDC transmit */ atmel_uart_writel (port,ATMEL_PDC_PTCR ,ATMEL_PDC_TXTEN ); + atmel_port->tx_done_mask |=ATMEL_US_TXRDY ; +/* Enable interrupts */ atmel_uart_writel (port,ATMEL_US_IER , atmel_port->tx_done_mask);
thanks,
Signature · 1 line
js
Re: [PATCH v5 2/3] tty: serial: use uart_port_tx() helper
Hi,
Am 2022-11-22 08:02, schrieb Jiri Slaby:
Quoted 33 lines · Michael Walle
Quoted 7 lines
This will break serial output for the userspace on my board (
arch/arm/boot/dts/lan966x-kontron-kswitch-d10-mmt*dts). Theuart_port_tx()helper will call__port->ops->stop_tx(__port)ifuart_circ_chars_pending()returns 0. But the code above, doesn't do that. In fact, removing thestop_tx()call in the helper macro, will fix the console output.Any ideas how to fix that?
Hm, so
ATMEL_US_TXRDYis removed fromtx_done_maskinstop_tx, but not added back instart_tx. So the tx interrupt is never handled (the tx tasklet is not scheduled to send the queue chars) inatmel_handle_transmit().Any chance, the below fixes it?
drivers/tty/serial/atmel_serial.c +2
-0@@ -596,6 +596,8 @@ static void atmel_start_tx(struct uart_port *port)/* re-enable PDC transmit */ atmel_uart_writel (port,ATMEL_PDC_PTCR ,ATMEL_PDC_TXTEN ); + atmel_port->tx_done_mask |=ATMEL_US_TXRDY ; +/* Enable interrupts */ atmel_uart_writel(port, ATMEL_US_IER,
atmel_port->tx_done_mask);
Quoted 1 line
thanks,
Unfortunately, that doesn't help. Btw, some characters are transmitted:
[ 6.219356] Key type dns_resolver registered [ 6.223679] Registering SWP/SWPB emulation handler [ 6.247530] Loading compiled-in X.509 certificates [ 6.288467] Freeing unused kernel image (initmem) memory: 1024K [ 6.297789] Run /init as init process
WbSOROSOSOSOSOStarting linuxptp system clock synchronization: O
-michael
Re: [PATCH v5 2/3] tty: serial: use uart_port_tx() helper
Am 2022-11-22 09:09, schrieb Michael Walle:
Quoted 41 lines
Hi,
Am 2022-11-22 08:02, schrieb Jiri Slaby:
Quoted 33 lines · Michael Walle
Quoted 7 lines
This will break serial output for the userspace on my board (
arch/arm/boot/dts/lan966x-kontron-kswitch-d10-mmt*dts). Theuart_port_tx()helper will call__port->ops->stop_tx(__port)ifuart_circ_chars_pending()returns 0. But the code above, doesn't do that. In fact, removing thestop_tx()call in the helper macro, will fix the console output.Any ideas how to fix that?
Hm, so
ATMEL_US_TXRDYis removed fromtx_done_maskinstop_tx, but not added back instart_tx. So the tx interrupt is never handled (the tx tasklet is not scheduled to send the queue chars) inatmel_handle_transmit().Any chance, the below fixes it?
drivers/tty/serial/atmel_serial.c +2
-0@@ -596,6 +596,8 @@ static void atmel_start_tx(struct uart_port *port)/* re-enable PDC transmit */ atmel_uart_writel (port,ATMEL_PDC_PTCR ,ATMEL_PDC_TXTEN ); + atmel_port->tx_done_mask |=ATMEL_US_TXRDY ; +/* Enable interrupts */ atmel_uart_writel(port, ATMEL_US_IER,
atmel_port->tx_done_mask);Quoted 1 line
thanks,
Unfortunately, that doesn't help. Btw, some characters are transmitted:
Quoted 8 lines
[ 6.219356] Key type dns_resolver registered [ 6.223679] Registering SWP/SWPB emulation handler [ 6.247530] Loading compiled-in X.509 certificates [ 6.288467] Freeing unused kernel image (initmem) memory: 1024K [ 6.297789] Run /init as init processWbSOROSOSOSOSOStarting linuxptp system clock synchronization: O
-michael
But you made me look at atmel_stop_tx() and there is this:
/*
* Disable the transmitter.
* This is mandatory when DMA is used, otherwise the DMA buffer
* is fully transmitted.
*/
atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXDIS);
Removing that write, will also fix the problem. Could it be, that the transmit is still active (via DMA) but the driver will call tx_stop() and then stop the transmission in the background?
-michael
Jiri Slaby
maintainerRe: [PATCH v5 2/3] tty: serial: use uart_port_tx() helper
Quoted 58 lines · Michael Walle
Am 2022-11-22 09:09, schrieb Michael Walle:
Quoted 39 lines
Hi,
Am 2022-11-22 08:02, schrieb Jiri Slaby:
Quoted 31 lines · Michael Walle
Quoted 7 lines
This will break serial output for the userspace on my board (
arch/arm/boot/dts/lan966x-kontron-kswitch-d10-mmt*dts). Theuart_port_tx()helper will call__port->ops->stop_tx(__port)ifuart_circ_chars_pending()returns 0. But the code above, doesn't do that. In fact, removing thestop_tx()call in the helper macro, will fix the console output.Any ideas how to fix that?
Hm, so
ATMEL_US_TXRDYis removed fromtx_done_maskinstop_tx, but not added back instart_tx. So the tx interrupt is never handled (the tx tasklet is not scheduled to send the queue chars) inatmel_handle_transmit().Any chance, the below fixes it?
drivers/tty/serial/atmel_serial.c +2
-0@@ -596,6 +596,8 @@ static void atmel_start_tx(struct uart_port *port) /* re-enable PDC transmit */ atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTEN); + atmel_port->tx_done_mask |= ATMEL_US_TXRDY; + /* Enable interrupts */ atmel_uart_writel(port, ATMEL_US_IER, atmel_port->tx_done_mask);Quoted 1 line
thanks,
Unfortunately, that doesn't help. Btw, some characters are transmitted:
Quoted 8 lines
[ 6.219356] Key type
dns_resolverregistered
[ 6.223679] Registering SWP/SWPB emulation handler
[ 6.247530] Loading compiled-in X.509 certificates
[ 6.288467] Freeing unused kernel image (initmem) memory: 1024K [ 6.297789] Run /init as init process WbSOROSOSOSOSOStarting linuxptp system clock synchronization: O-michael
But you made me look at
atmel_stop_tx()and there is this:/*
* Disable the transmitter.
* This is mandatory when DMA is used, otherwise the DMA buffer
* is fully transmitted.
*/
atmel_uart_writel(port,ATMEL_US_CR,ATMEL_US_TXDIS);
Quoted 3 lines
Removing that write, will also fix the problem. Could it be, that the transmit is still active (via DMA) but the driver will call
tx_stop()and then stop the transmission in the background?
Yes, that was exactly the next step to try. The datasheet doesn't tell much what happens when TXDIS is written while the characters are transmitted. So can you give the attached patch a try?
thanks,
Signature · 1 line
js
From 2dcc79384b97a2176bbf84ea634aae4a26efd0b4 Mon Sep 17 00:00:00 2001
From: "Jiri Slaby (SUSE)" <[email protected]>
Date: Tue, 22 Nov 2022 09:05:51 +0100
Subject: [PATCH] atmel: fix
--- drivers/tty/serial/atmel_serial.c | 40 ++++++++++++++++++------------- 1 file changed, 24 insertions(+), 16 deletions(-)
drivers/tty/serial/atmel_serial.c +24 -16
@@ -552,19 +552,23 @@ static u_int atmel_get_mctrl(struct uart_port *port)static void atmel_stop_tx (struct uart_port *port) {struct atmel_uart_port *atmel_port =to_atmel_uart_port (port); +bool is_pdc =atmel_use_pdc_tx (port); +bool is_dma = is_pdc ||atmel_use_dma_tx (port); -if (atmel_use_pdc_tx (port)) { +if (is_pdc) {/* disable PDC transmit */ atmel_uart_writel (port,ATMEL_PDC_PTCR ,ATMEL_PDC_TXTDIS ); } -/* -* Disable the transmitter. -* This is mandatory when DMA is used, otherwise the DMA buffer -* is fully transmitted. -*/ -atmel_uart_writel (port,ATMEL_US_CR ,ATMEL_US_TXDIS ); - atmel_port->tx_stopped = true; +if (is_dma) { +/* +* Disable the transmitter. +* This is mandatory when DMA is used, otherwise the DMA buffer +* is fully transmitted. +*/ +atmel_uart_writel (port,ATMEL_US_CR ,ATMEL_US_TXDIS ); + atmel_port->tx_stopped = true; + }/* Disable interrupts */ atmel_uart_writel (port,ATMEL_US_IDR , atmel_port->tx_done_mask);
@@ -581,27 +585,31 @@ static void atmel_stop_tx(struct uart_port *port)static void atmel_start_tx (struct uart_port *port) {struct atmel_uart_port *atmel_port =to_atmel_uart_port (port); +bool is_pdc =atmel_use_pdc_tx (port); +bool is_dma = is_pdc ||atmel_use_dma_tx (port); -if (atmel_use_pdc_tx (port) && (atmel_uart_readl (port,ATMEL_PDC_PTSR ) +if (is_pdc && (atmel_uart_readl (port,ATMEL_PDC_PTSR ) &ATMEL_PDC_TXTEN ))/* The transmitter is already running. Yes, we really need this.*/ return ; -if (atmel_use_pdc_tx (port) ||atmel_use_dma_tx (port)) -if (atmel_uart_is_half_duplex (port)) -atmel_stop_rx (port); +if (id_dma &&atmel_uart_is_half_duplex (port)) +atmel_stop_rx (port); -if (atmel_use_pdc_tx (port)) +if (is_pdc) {/* re-enable PDC transmit */ atmel_uart_writel (port,ATMEL_PDC_PTCR ,ATMEL_PDC_TXTEN ); + }/* Enable interrupts */ atmel_uart_writel (port,ATMEL_US_IER , atmel_port->tx_done_mask); -/* re-enable the transmitter */ -atmel_uart_writel (port,ATMEL_US_CR ,ATMEL_US_TXEN ); - atmel_port->tx_stopped = false; +if (is_dma) { +/* re-enable the transmitter */ +atmel_uart_writel (port,ATMEL_US_CR ,ATMEL_US_TXEN ); + atmel_port->tx_stopped = false; + } }/*
Signature · 1 line
2.38.1
Jiri Slaby
maintainerRe: [PATCH v5 2/3] tty: serial: use uart_port_tx() helper
Quoted 59 lines · Jiri Slaby
Quoted 58 lines · Michael Walle
Am 2022-11-22 09:09, schrieb Michael Walle:
Quoted 39 lines
Hi,
Am 2022-11-22 08:02, schrieb Jiri Slaby:
Quoted 31 lines · Michael Walle
Quoted 7 lines
This will break serial output for the userspace on my board (
arch/arm/boot/dts/lan966x-kontron-kswitch-d10-mmt*dts). Theuart_port_tx()helper will call__port->ops->stop_tx(__port)ifuart_circ_chars_pending()returns 0. But the code above, doesn't do that. In fact, removing thestop_tx()call in the helper macro, will fix the console output.Any ideas how to fix that?
Hm, so
ATMEL_US_TXRDYis removed fromtx_done_maskinstop_tx, but not added back instart_tx. So the tx interrupt is never handled (the tx tasklet is not scheduled to send the queue chars) inatmel_handle_transmit().Any chance, the below fixes it?
drivers/tty/serial/atmel_serial.c +2
-0@@ -596,6 +596,8 @@ static void atmel_start_tx(struct uart_port *port) /* re-enable PDC transmit */ atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTEN); + atmel_port->tx_done_mask |= ATMEL_US_TXRDY; + /* Enable interrupts */ atmel_uart_writel(port, ATMEL_US_IER, atmel_port->tx_done_mask);Quoted 1 line
thanks,
Unfortunately, that doesn't help. Btw, some characters are transmitted:
Quoted 8 lines
[ 6.219356] Key type
dns_resolverregistered
[ 6.223679] Registering SWP/SWPB emulation handler
[ 6.247530] Loading compiled-in X.509 certificates
[ 6.288467] Freeing unused kernel image (initmem) memory: 1024K [ 6.297789] Run /init as init process WbSOROSOSOSOSOStarting linuxptp system clock synchronization: O-michael
But you made me look at
atmel_stop_tx()and there is this:/*
* Disable the transmitter.
* This is mandatory when DMA is used, otherwise the DMA buffer
* is fully transmitted.
*/
atmel_uart_writel(port,ATMEL_US_CR,ATMEL_US_TXDIS);
Quoted 5 lines
Quoted 3 lines
Removing that write, will also fix the problem. Could it be, that the transmit is still active (via DMA) but the driver will call
tx_stop()and then stop the transmission in the background?Yes, that was exactly the next step to try. The datasheet doesn't tell much what happens when TXDIS is written while the characters are transmitted.
Side note: your usart doesn't use dma. It's PIO (hence all that uart_tx_helper()). And the attached patch doesn't touch TXDIS for non-DMA case. I.e. it should transmit the final character (and nothing more).
Signature · 1 line
js
Re: [PATCH v5 2/3] tty: serial: use uart_port_tx() helper
Am 2022-11-22 09:25, schrieb Jiri Slaby:
Quoted 65 lines · Jiri Slaby
Quoted 64 lines · Michael Walle
Quoted 62 lines
Am 2022-11-22 09:09, schrieb Michael Walle:
Quoted 40 lines
Hi,
Am 2022-11-22 08:02, schrieb Jiri Slaby:
Quoted 32 lines · Michael Walle
Quoted 7 lines
This will break serial output for the userspace on my board (
arch/arm/boot/dts/lan966x-kontron-kswitch-d10-mmt*dts). Theuart_port_tx()helper will call__port->ops->stop_tx(__port)ifuart_circ_chars_pending()returns 0. But the code above, doesn't do that. In fact, removing thestop_tx()call in the helper macro, will fix the console output.Any ideas how to fix that?
Hm, so
ATMEL_US_TXRDYis removed fromtx_done_maskinstop_tx, but not added back instart_tx. So the tx interrupt is never handled (the tx tasklet is not scheduled to send the queue chars) inatmel_handle_transmit().Any chance, the below fixes it?
drivers/tty/serial/atmel_serial.c +2
-0@@ -596,6 +596,8 @@ static void atmel_start_tx(struct uart_port *port) /* re-enable PDC transmit */ atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTEN); + atmel_port->tx_done_mask |= ATMEL_US_TXRDY; + /* Enable interrupts */ atmel_uart_writel(port, ATMEL_US_IER, atmel_port->tx_done_mask);Quoted 1 line
thanks,
Unfortunately, that doesn't help. Btw, some characters are transmitted:
Quoted 8 lines
[ 6.219356] Key type
dns_resolverregistered
[ 6.223679] Registering SWP/SWPB emulation handler
[ 6.247530] Loading compiled-in X.509 certificates
[ 6.288467] Freeing unused kernel image (initmem) memory: 1024K [ 6.297789] Run /init as init process WbSOROSOSOSOSOStarting linuxptp system clock synchronization: O-michael
But you made me look at
atmel_stop_tx()and there is this:/*
* Disable the transmitter.
* This is mandatory when DMA is used, otherwise the DMA buffer
* is fully transmitted.
*/
atmel_uart_writel(port,ATMEL_US_CR,ATMEL_US_TXDIS);Removing that write, will also fix the problem. Could it be, that the transmit is still active (via DMA) but the driver will call
tx_stop()and then stop the transmission in the background?
Quoted 6 lines
Quoted 1 line
Yes, that was exactly the next step to try. The datasheet doesn't tell much what happens when TXDIS is written while the characters are transmitted.
Side note: your usart doesn't use dma. It's PIO (hence all that
uart_tx_helper()). And the attached patch doesn't touch TXDIS for non-DMA case. I.e. it should transmit the final character (and nothing more).
ok ;)
expect from "s/id_dma/is_dma/", this patch works. thanks!
-michael
Jiri Slaby (SUSE)
maintainerPATCH v5 3/3 tty: serial: use uart_port_tx_limited()
In reply to Jiri Slaby (SUSE)uart_port_tx_limited() is a new helper to send characters to the device. Use it in these drivers.
mux.c also needs to define tx_done(). But I'm not sure if the driver really wants to wait for all the characters to dismiss from the HW fifo at this code point. Hence I marked this as FIXME.
---
Notes:
[v4] switch from DEFINE_UART_PORT_TX_HELPER_LIMITED() (helper generator)
to uart_port_tx_limited() (akin to wait_event())
drivers/tty/serial/21285.c | 32 +++---------------- drivers/tty/serial/altera_jtaguart.c | 36 ++++----------------- drivers/tty/serial/amba-pl010.c | 32 +++---------------- drivers/tty/serial/apbuart.c | 34 +++----------------- drivers/tty/serial/bcm63xx_uart.c | 47 ++++++--------------------- drivers/tty/serial/mux.c | 45 ++++++++------------------ drivers/tty/serial/mvebu-uart.c | 38 +++------------------- drivers/tty/serial/omap-serial.c | 32 +++---------------- drivers/tty/serial/pxa.c | 33 +++---------------- drivers/tty/serial/rp2.c | 31 ++++-------------- drivers/tty/serial/serial_txx9.c | 32 +++---------------- drivers/tty/serial/sifive.c | 31 +++--------------- drivers/tty/serial/sprd_serial.c | 33 +++---------------- drivers/tty/serial/st-asc.c | 48 +++------------------------- 14 files changed, 85 insertions(+), 419 deletions(-)
drivers/tty/serial/21285.c +5 -27
@@ -154,35 +154,13 @@ static irqreturn_t serial21285_rx_chars(int irq, void *dev_id)static irqreturn_t serial21285_tx_chars (int irq,void *dev_id) {struct uart_port *port = dev_id; -struct circ_buf *xmit = &port->state->xmit; -int count =256 ; - -if (port->x_char) { - *CSR_UARTDR = port->x_char; - port->icount.tx++; - port->x_char =0 ; - goto out; - } -if (uart_circ_empty (xmit) ||uart_tx_stopped (port)) { -serial21285_stop_tx (port); - goto out; - } - -do { - *CSR_UARTDR = xmit->buf[xmit->tail]; - xmit->tail = (xmit->tail +1 ) & (UART_XMIT_SIZE -1 ); - port->icount.tx++; -if (uart_circ_empty (xmit)) -break ; - }while (--count >0 && !(*CSR_UARTFLG &0x20 )); - -if (uart_circ_chars_pending (xmit) <WAKEUP_CHARS ) -uart_write_wakeup (port); +u8 ch; -if (uart_circ_empty (xmit)) -serial21285_stop_tx (port); +uart_port_tx_limited (port, ch,256 , + !(*CSR_UARTFLG &0x20 ), + *CSR_UARTDR = ch, + ({})); - out:return IRQ_HANDLED ; }
drivers/tty/serial/altera_jtaguart.c +7 -29
@@ -146,37 +146,15 @@ static void altera_jtaguart_rx_chars(struct altera_jtaguart *pp)static void altera_jtaguart_tx_chars (struct altera_jtaguart *pp) {struct uart_port *port = &pp->port; -struct circ_buf *xmit = &port->state->xmit; -unsigned int pending, count; - -if (port->x_char) { -/* Send special char - probably flow control */ -writel (port->x_char, port->membase +ALTERA_JTAGUART_DATA_REG ); - port->x_char =0 ; - port->icount.tx++; -return ; - } +unsigned int count; +u8 ch; - pending =uart_circ_chars_pending (xmit); -if (pending >0 ) { - count =altera_jtaguart_tx_space (port,NULL ); -if (count > pending) - count = pending; -if (count >0 ) { - pending -= count; -while (count--) { -writel (xmit->buf[xmit->tail], - port->membase +ALTERA_JTAGUART_DATA_REG ); - xmit->tail = (xmit->tail +1 ) & (UART_XMIT_SIZE -1 ); - port->icount.tx++; - } -if (pending <WAKEUP_CHARS ) -uart_write_wakeup (port); - } - } + count =altera_jtaguart_tx_space (port,NULL ); -if (pending ==0 ) -altera_jtaguart_stop_tx (port); +uart_port_tx_limited (port, ch, count, + true, +writel (ch, port->membase +ALTERA_JTAGUART_DATA_REG ), + ({})); }static irqreturn_t altera_jtaguart_interrupt (int irq,void *data)
drivers/tty/serial/amba-pl010.c +5 -27
@@ -164,34 +164,12 @@ static void pl010_rx_chars(struct uart_port *port)static void pl010_tx_chars (struct uart_port *port) { -struct circ_buf *xmit = &port->state->xmit; -int count; +u8 ch; -if (port->x_char) { -writel (port->x_char, port->membase + UART01x_DR); - port->icount.tx++; - port->x_char =0 ; -return ; - } -if (uart_circ_empty (xmit) ||uart_tx_stopped (port)) { -pl010_stop_tx (port); -return ; - } - - count = port->fifosize >>1 ; -do { -writel (xmit->buf[xmit->tail], port->membase + UART01x_DR); - xmit->tail = (xmit->tail +1 ) & (UART_XMIT_SIZE -1 ); - port->icount.tx++; -if (uart_circ_empty (xmit)) -break ; - }while (--count >0 ); - -if (uart_circ_chars_pending (xmit) <WAKEUP_CHARS ) -uart_write_wakeup (port); - -if (uart_circ_empty (xmit)) -pl010_stop_tx (port); +uart_port_tx_limited (port, ch, port->fifosize >>1 , + true, +writel (ch, port->membase + UART01x_DR), + ({})); }static void pl010_modem_status (struct uart_amba_port *uap)
drivers/tty/serial/apbuart.c +5 -29
@@ -122,36 +122,12 @@ static void apbuart_rx_chars(struct uart_port *port)static void apbuart_tx_chars (struct uart_port *port) { -struct circ_buf *xmit = &port->state->xmit; -int count; - -if (port->x_char) { -UART_PUT_CHAR (port, port->x_char); - port->icount.tx++; - port->x_char =0 ; -return ; - } - -if (uart_circ_empty (xmit) ||uart_tx_stopped (port)) { -apbuart_stop_tx (port); -return ; - } - -/* amba: fill FIFO */ - count = port->fifosize >>1 ; -do { -UART_PUT_CHAR (port, xmit->buf[xmit->tail]); - xmit->tail = (xmit->tail +1 ) & (UART_XMIT_SIZE -1 ); - port->icount.tx++; -if (uart_circ_empty (xmit)) -break ; - }while (--count >0 ); - -if (uart_circ_chars_pending (xmit) <WAKEUP_CHARS ) -uart_write_wakeup (port); +u8 ch; -if (uart_circ_empty (xmit)) -apbuart_stop_tx (port); +uart_port_tx_limited (port, ch, port->fifosize >>1 , + true, +UART_PUT_CHAR (port, ch), + ({})); }static irqreturn_t apbuart_int (int irq,void *dev_id)
drivers/tty/serial/bcm63xx_uart.c +9 -38
62 lines not on this page · raw message
drivers/tty/serial/mux.c +13 -32
58 lines not on this page · raw message
drivers/tty/serial/mvebu-uart.c +5 -33
@@ -335,40 +335,12 @@ static void mvebu_uart_rx_chars(struct uart_port *port, unsigned int status)static void mvebu_uart_tx_chars (struct uart_port *port,unsigned int status) { -struct circ_buf *xmit = &port->state->xmit; -unsigned int count; -unsigned int st; - -if (port->x_char) { -writel (port->x_char, port->membase +UART_TSH (port)); - port->icount.tx++; - port->x_char =0 ; -return ; - } - -if (uart_circ_empty (xmit) ||uart_tx_stopped (port)) { -mvebu_uart_stop_tx (port); -return ; - } - -for (count =0 ; count < port->fifosize; count++) { -writel (xmit->buf[xmit->tail], port->membase +UART_TSH (port)); - xmit->tail = (xmit->tail +1 ) & (UART_XMIT_SIZE -1 ); - port->icount.tx++; - -if (uart_circ_empty (xmit)) -break ; - - st =readl (port->membase +UART_STAT ); -if (st &STAT_TX_FIFO_FUL ) -break ; - } - -if (uart_circ_chars_pending (xmit) <WAKEUP_CHARS ) -uart_write_wakeup (port); +u8 ch; -if (uart_circ_empty (xmit)) -mvebu_uart_stop_tx (port); +uart_port_tx_limited (port, ch, port->fifosize, + !(readl (port->membase +UART_STAT ) &STAT_TX_FIFO_FUL ), +writel (ch, port->membase +UART_TSH (port)), + ({})); }static irqreturn_t mvebu_uart_isr (int irq,void *dev_id)
drivers/tty/serial/omap-serial.c +5 -27
@@ -347,34 +347,12 @@ static void serial_omap_put_char(struct uart_omap_port *up, unsigned char ch)static void transmit_chars (struct uart_omap_port *up,unsigned int lsr) { -struct circ_buf *xmit = &up->port.state->xmit; -int count; +u8 ch; -if (up->port.x_char) { -serial_omap_put_char (up, up->port.x_char); - up->port.icount.tx++; - up->port.x_char =0 ; -return ; - } -if (uart_circ_empty (xmit) ||uart_tx_stopped (&up->port)) { -serial_omap_stop_tx (&up->port); -return ; - } - count = up->port.fifosize /4 ; -do { -serial_omap_put_char (up, xmit->buf[xmit->tail]); - xmit->tail = (xmit->tail +1 ) & (UART_XMIT_SIZE -1 ); - up->port.icount.tx++; - -if (uart_circ_empty (xmit)) -break ; - }while (--count >0 ); - -if (uart_circ_chars_pending (xmit) <WAKEUP_CHARS ) -uart_write_wakeup (&up->port); - -if (uart_circ_empty (xmit)) -serial_omap_stop_tx (&up->port); +uart_port_tx_limited (&up->port, ch, up->port.fifosize /4 , + true, +serial_omap_put_char (up, ch), + ({})); }static inline void serial_omap_enable_ier_thri (struct uart_omap_port *up)
drivers/tty/serial/pxa.c +5 -28
@@ -174,35 +174,12 @@ static inline void receive_chars(struct uart_pxa_port *up, int *status)static void transmit_chars (struct uart_pxa_port *up) { -struct circ_buf *xmit = &up->port.state->xmit; -int count; +u8 ch; -if (up->port.x_char) { -serial_out (up,UART_TX , up->port.x_char); - up->port.icount.tx++; - up->port.x_char =0 ; -return ; - } -if (uart_circ_empty (xmit) ||uart_tx_stopped (&up->port)) { -serial_pxa_stop_tx (&up->port); -return ; - } - - count = up->port.fifosize /2 ; -do { -serial_out (up,UART_TX , xmit->buf[xmit->tail]); - xmit->tail = (xmit->tail +1 ) & (UART_XMIT_SIZE -1 ); - up->port.icount.tx++; -if (uart_circ_empty (xmit)) -break ; - }while (--count >0 ); - -if (uart_circ_chars_pending (xmit) <WAKEUP_CHARS ) -uart_write_wakeup (&up->port); - - -if (uart_circ_empty (xmit)) -serial_pxa_stop_tx (&up->port); +uart_port_tx_limited (&up->port, ch, up->port.fifosize /2 , + true, +serial_out (up,UART_TX , ch), + ({})); }static void serial_pxa_start_tx (struct uart_port *port)
drivers/tty/serial/rp2.c +6 -25
@@ -427,32 +427,13 @@ static void rp2_rx_chars(struct rp2_uart_port *up)static void rp2_tx_chars (struct rp2_uart_port *up) { -u16 max_tx =FIFO_SIZE -readw (up->base +RP2_TX_FIFO_COUNT ); -struct circ_buf *xmit = &up->port.state->xmit; +u8 ch; -if (uart_tx_stopped (&up->port)) { -rp2_uart_stop_tx (&up->port); -return ; - } - -for (; max_tx !=0 ; max_tx--) { -if (up->port.x_char) { -writeb (up->port.x_char, up->base +RP2_DATA_BYTE ); - up->port.x_char =0 ; - up->port.icount.tx++; -continue ; - } -if (uart_circ_empty (xmit)) { -rp2_uart_stop_tx (&up->port); -break ; - } -writeb (xmit->buf[xmit->tail], up->base +RP2_DATA_BYTE ); - xmit->tail = (xmit->tail +1 ) & (UART_XMIT_SIZE -1 ); - up->port.icount.tx++; - } - -if (uart_circ_chars_pending (xmit) <WAKEUP_CHARS ) -uart_write_wakeup (&up->port); +uart_port_tx_limited (&up->port, ch, +FIFO_SIZE -readw (up->base +RP2_TX_FIFO_COUNT ), + true, +writeb (ch, up->base +RP2_DATA_BYTE ), + ({})); }static void rp2_ch_interrupt (struct rp2_uart_port *up)
drivers/tty/serial/serial_txx9.c +5 -27
@@ -321,34 +321,12 @@ receive_chars(struct uart_port *up, unsigned int *status)static inline void transmit_chars (struct uart_port *up) { -struct circ_buf *xmit = &up->state->xmit; -int count; +u8 ch; -if (up->x_char) { -sio_out (up,TXX9_SITFIFO , up->x_char); - up->icount.tx++; - up->x_char =0 ; -return ; - } -if (uart_circ_empty (xmit) ||uart_tx_stopped (up)) { -serial_txx9_stop_tx (up); -return ; - } - - count =TXX9_SIO_TX_FIFO ; -do { -sio_out (up,TXX9_SITFIFO , xmit->buf[xmit->tail]); - xmit->tail = (xmit->tail +1 ) & (UART_XMIT_SIZE -1 ); - up->icount.tx++; -if (uart_circ_empty (xmit)) -break ; - }while (--count >0 ); - -if (uart_circ_chars_pending (xmit) <WAKEUP_CHARS ) -uart_write_wakeup (up); - -if (uart_circ_empty (xmit)) -serial_txx9_stop_tx (up); +uart_port_tx_limited (up, ch,TXX9_SIO_TX_FIFO , + true, +sio_out (up,TXX9_SITFIFO , ch), + ({})); }static irqreturn_t serial_txx9_interrupt (int irq,void *dev_id)
drivers/tty/serial/sifive.c +5 -26
@@ -288,33 +288,12 @@ static void __ssp_transmit_char(struct sifive_serial_port *ssp, int ch)*/ static void __ssp_transmit_chars (struct sifive_serial_port *ssp) { -struct circ_buf *xmit = &ssp->port.state->xmit; -int count; - -if (ssp->port.x_char) { -__ssp_transmit_char (ssp, ssp->port.x_char); - ssp->port.icount.tx++; - ssp->port.x_char =0 ; -return ; - } -if (uart_circ_empty (xmit) ||uart_tx_stopped (&ssp->port)) { -sifive_serial_stop_tx (&ssp->port); -return ; - } - count =SIFIVE_TX_FIFO_DEPTH ; -do { -__ssp_transmit_char (ssp, xmit->buf[xmit->tail]); - xmit->tail = (xmit->tail +1 ) & (UART_XMIT_SIZE -1 ); - ssp->port.icount.tx++; -if (uart_circ_empty (xmit)) -break ; - }while (--count >0 ); - -if (uart_circ_chars_pending (xmit) <WAKEUP_CHARS ) -uart_write_wakeup (&ssp->port); +u8 ch; -if (uart_circ_empty (xmit)) -sifive_serial_stop_tx (&ssp->port); +uart_port_tx_limited (&ssp->port, ch,SIFIVE_TX_FIFO_DEPTH , + true, +__ssp_transmit_char (ssp, ch), + ({})); }/**
drivers/tty/serial/sprd_serial.c +5 -28
@@ -626,35 +626,12 @@ static inline void sprd_rx(struct uart_port *port)static inline void sprd_tx (struct uart_port *port) { -struct circ_buf *xmit = &port->state->xmit; -int count; - -if (port->x_char) { -serial_out (port,SPRD_TXD , port->x_char); - port->icount.tx++; - port->x_char =0 ; -return ; - } - -if (uart_circ_empty (xmit) ||uart_tx_stopped (port)) { -sprd_stop_tx (port); -return ; - } - - count =THLD_TX_EMPTY ; -do { -serial_out (port,SPRD_TXD , xmit->buf[xmit->tail]); - xmit->tail = (xmit->tail +1 ) & (UART_XMIT_SIZE -1 ); - port->icount.tx++; -if (uart_circ_empty (xmit)) -break ; - }while (--count >0 ); - -if (uart_circ_chars_pending (xmit) <WAKEUP_CHARS ) -uart_write_wakeup (port); +u8 ch; -if (uart_circ_empty (xmit)) -sprd_stop_tx (port); +uart_port_tx_limited (port, ch,THLD_TX_EMPTY , + true, +serial_out (port,SPRD_TXD , ch), + ({})); }/* this handles the interrupt from one port */
drivers/tty/serial/st-asc.c +5 -43
55 lines not on this page · raw message
Signature · 7 lines
2.37.3 _______________________________________________ linux-riscv mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-riscv
Re: [PATCH v5 3/3] tty: serial: use uart_port_tx_limited()
Quoted 7 lines · Jiri Slaby (SUSE)
uart_port_tx_limited()is a new helper to send characters to the device. Use it in these drivers.
mux.calso needs to definetx_done(). But I'm not sure if the driver really wants to wait for all the characters to dismiss from the HW fifo at this code point. Hence I marked this as FIXME.
Quoted 13 lines
Cc Russell King <[email protected]>Cc Florian Fainelli <[email protected]>Cc "Pali Rohár" <[email protected]>Cc Kevin Cernekee <[email protected]>Cc Palmer Dabbelt <[email protected]>Cc Paul Walmsley <[email protected]>Cc Orson Zhai <[email protected]>Cc Baolin Wang <[email protected]>Cc Chunyan Zhang <[email protected]>Cc Patrice Chotard <[email protected]>Signed-off-by Jiri Slaby (SUSE) <[email protected]>
Perhaps you missed this one in the earlier mail. ...Anyway, here it's again:
Signature · 1 line
i.