Skip to contentSkip to conversation

what all has changed in ppp?

DISCUSSION [email protected] 2 participants 4 messages Feb 2, 2003

lore
Share & tools
lore
#0 lore raw

sorry, I haven't been keeping up with the changes in 2.5, but I can't get pppd to work with 2.5.59, it dies with error code 1 while it works alright with 2.4.20...

This is the first 2.5 kernel i've tried out, first I went for a wild goose chase in finding a version of modutils to go with the shiny new bzImage, then I finally downloaded module-init*, and installed it over the previous tools, then I remembered that I still might have to use 2.4 (which I am), so I fetched modutils again and installed it, then I installed module-init* with make *specialoption*, and then (aaah, finished...)but no, I cannot dial to my isp... pppd dies with error code 1

Also, Does a Pentium4 have a local APIC? IO APIC?
I selected it anyway in the kernel config, and it shows some warning message at boot:

: ENABLING IO-APIC IRQs
: init IO_APIC IRQs
: IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-21, 2-22, 2-23 not connected. : ..TIMER: vector=0x31 pin1=2 pin2=0
: number of MP IRQ sources: 17.
: number of IO-APIC #2 registers: 24.
: testing the IO APIC.......................
:
: IO APIC #2......
: .... register #00: 02000000

: .......    : physical APIC id: 02
: .......    : Delivery Type: 0
: .......    : LTS          : 0
: .... register #01: 00178000
: .......     : max redirection entries: 0017
: .......     : PRQ implemented: 1
: .......     : IO APIC version: 0000
:  WARNING: unexpected IO-APIC, please mail
:           to [email protected]
: .... IRQ redirection table:
:  NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
:  00 000 00  1    0    0   0   0    0    0    00
:  01 001 01  0    0    0   0   0    1    1    39
:  02 001 01  0    0    0   0   0    1    1    31
:  03 001 01  0    0    0   0   0    1    1    41
:  04 001 01  0    0    0   0   0    1    1    49
:  05 001 01  0    0    0   0   0    1    1    51
:  06 001 01  0    0    0   0   0    1    1    59
:  07 001 01  0    0    0   0   0    1    1    61
:  08 001 01  0    0    0   0   0    1    1    69
:  09 001 01  0    0    0   0   0    1    1    71
:  0a 001 01  0    0    0   0   0    1    1    79
:  0b 001 01  0    0    0   0   0    1    1    81
:  0c 001 01  0    0    0   0   0    1    1    89
:  0d 001 01  0    0    0   0   0    1    1    91
:  0e 001 01  0    0    0   0   0    1    1    99
:  0f 001 01  0    0    0   0   0    1    1    A1
:  10 000 00  1    0    0   0   0    0    0    00
:  11 000 00  1    0    0   0   0    0    0    00
:  12 000 00  1    0    0   0   0    0    0    00
:  13 000 00  1    0    0   0   0    0    0    00
:  14 001 01  1    1    0   1   0    1    1    71
:  15 000 00  1    0    0   0   0    0    0    00
:  16 000 00  1    0    0   0   0    0    0    00
:  17 000 00  1    0    0   0   0    0    0    00

: IRQ to pin mappings:
: IRQ0 -> 0:2
: IRQ1 -> 0:1
: IRQ3 -> 0:3
: IRQ4 -> 0:4
: IRQ5 -> 0:5
: IRQ6 -> 0:6
: IRQ7 -> 0:7
: IRQ8 -> 0:8
: IRQ9 -> 0:9-> 0:20
: IRQ10 -> 0:10
: IRQ11 -> 0:11
: IRQ12 -> 0:12
: IRQ13 -> 0:13
: IRQ14 -> 0:14
: IRQ15 -> 0:15
: .................................... done.
: Using local APIC timer interrupts.
: calibrating APIC timer ...
: ..... CPU clock speed is 2659.0663 MHz.
: ..... host bus clock speed is 132.0983 MHz.

Is anything wrong with this?
thank you very much for reading/replying

#1 lore raw
Quoted 3 lines · On Sun, Feb 02, 2003 at 10:47:37AM -0700, [email protected] wrote:

sorry, I haven't been keeping up with the changes in 2.5, but I can't get pppd to work with 2.5.59, it dies with error code 1 while it works alright with 2.4.20...

You need to look in the system log files (typically /var/log/messages) to see why pppd isn't happy.

Signature · 2 lines
Russell King ([email protected])                The developer of ARM Linux
             http://www.arm.linux.org.uk/personal/aboutme.html
#2 lore raw
Quoted 5 lines · Russell King
Quoted 1 line · On Sun, Feb 02, 2003 at 10:47:37AM -0700, [email protected] wrote:

sorry, I haven't been keeping up with the changes in 2.5, but I can't get pppd to work with 2.5.59, it dies with error code 1 while it works alright with 2.4.20...

You need to look in the system log files (typically /var/log/messages) to see why pppd isn't happy.

Oh yes, sorry I forgot, module tty_ldisk3 cannot be found, so ppp dies with exit status 1...
I didn't think ppp needs anything other than ppp_generic, the serial driver for ppp and the compression modules... What is tty_ldisk3? could you help me on this?

Also, I haven't been able to solve the cpu problem...
and also, modprobe warns of unknown symbols in /etc/modules.devfs...although the 2.4 kernel works fine...

#3 lore raw
Quoted 5 lines · On Sun, Feb 02, 2003 at 02:00:33PM -0700, [email protected] wrote:

Oh yes, sorry I forgot, module tty_ldisk3 cannot be found, so ppp dies with exit status 1...
I didn't think ppp needs anything other than ppp_generic, the serial driver for ppp and the compression modules...
What is tty_ldisk3? could you help me on this?

It's the ppp line discipline. Add to /etc/modules.conf:

alias tty-ldisc-3 ppp_async

Signature · 2 lines
Russell King ([email protected])                The developer of ARM Linux
             http://www.arm.linux.org.uk/personal/aboutme.html