Support for XPedite5370 and misc GPIO

NOTE: If there are still concerns about the ds4510 driver, feel free to leave it out of this patch series and only apply "Add support for PCA953x I2C gpio devices" and "XPedite5370 board support". I'd rather get those 2 changes merged in for the upcoming release and deal with the ds4510 later if need be.

Hello,
This patch series adds support for the XPedite5370 SBC. Its an MPC8572-based VPX card with a PMC/XMC site. The XPedite5370 includes a significant number of I2C GPIO devices (5) which are used for board configuration. I added support for 2 new I2C gpio devices in a new drivers/gpio directory. I'm not sure if this is the preferred location/method, so let me know if others have have different preferences. It'd be nice to have a more generic GPIO framework (like Linux's) at some point, but figured this was a step in the right direction by providing a place for generic GPIO devices in drivers/gpio.

Thanks,
Peter

Changes since v1:
- Rebased to u-boot-mpc85xx tree
- Updated NOR flash remapping method
- Added CONFIG_SYS_I2C2_OFFSET define to XPEDITE5370.h
- Removed CONFIG_SYS_EEPROM_PAGE_WRITE_ENABLE from XPEDITE5370.h

Changes since v2:
pca953x.c:
- Use cmd_tbl_t for subcommand parsing
- Made 'info' command dependent on CONFIG_CMD_PCA953X_INFO
- Removed chip command parameters, added 'device' subcommand

ds4510.c:
- Use cmd_tbl_t for subcommand parsing
- Made 'info' command dependent on CONFIG_CMD_DS4510_INFO
- Made memory commands dependent on CONFIG_CMD_DS4510_MEM
- Made 'rst' command dependent on CONFIG_CMD_DS4510_RST
- Removed chip command parameters, added 'device' subcommand
- Fixed multiline comment style
- moved to drivers/misc

xpedite5370:
- Changed alignment by spaces to alignment by tabs
- Fixed gur->devdisr typo for PCIe2
- Fixed some lines over 80 chars
- Fixed multiline comment style
- Cleaned up environment defines

Changes since v3:
- Removed CONFIG_L1_INIT_RAM reference

Changes since v4:
- Legitimately fixed gur->devdisr typo for PCIe2/3

Changes since v5:
- Additional error checks in pca953x.c and ds4510.c
- Changed usage of maxargs for command parsing in pca953x.c and ds4510.c
- Moved include/gpio/pca953x.h to include/pca953x.h
- Moved include/gpio/ds4510.h to include/ds4510.h
- Rebased on current TOT

Peter Tyser (3):
Add support for PCA953x I2C gpio devices
Add support for Maxim's DS4510 I2C device
XPedite5370 board support

 MAINTAINERS                         |    3 +
 MAKEALL                             |    1 +
 Makefile                            |    5 +
 README                              |   13 +
 board/xes/common/Makefile           |   56 ++++
 board/xes/common/fsl_8572_clk.c     |   51 +++
 board/xes/common/fsl_85xx_ddr.c     |   93 ++++++
 board/xes/common/fsl_85xx_pci.c     |  265 ++++++++++++++++
 board/xes/xpedite5370/Makefile      |   45 +++
 board/xes/xpedite5370/config.mk     |   35 ++
 board/xes/xpedite5370/ddr.c         |  270 ++++++++++++++++
 board/xes/xpedite5370/law.c         |   54 ++++
 board/xes/xpedite5370/tlb.c         |   94 ++++++
 board/xes/xpedite5370/u-boot.lds    |  145 +++++++++
 board/xes/xpedite5370/xpedite5370.c |  128 ++++++++
 drivers/gpio/Makefile               |   47 +++
 drivers/gpio/pca953x.c              |  227 ++++++++++++++
 drivers/misc/Makefile               |    1 +
 drivers/misc/ds4510.c               |  424 +++++++++++++++++++++++++
 include/configs/XPEDITE5370.h       |  589 +++++++++++++++++++++++++++++++++++
 include/ds4510.h                    |   75 +++++
 include/pca953x.h                   |   39 +++
 22 files changed, 2660 insertions(+), 0 deletions(-)
 create mode 100644 board/xes/common/Makefile
 create mode 100644 board/xes/common/fsl_8572_clk.c
 create mode 100644 board/xes/common/fsl_85xx_ddr.c
 create mode 100644 board/xes/common/fsl_85xx_pci.c
 create mode 100644 board/xes/xpedite5370/Makefile
 create mode 100644 board/xes/xpedite5370/config.mk
 create mode 100644 board/xes/xpedite5370/ddr.c
 create mode 100644 board/xes/xpedite5370/law.c
 create mode 100644 board/xes/xpedite5370/tlb.c
 create mode 100644 board/xes/xpedite5370/u-boot.lds
 create mode 100644 board/xes/xpedite5370/xpedite5370.c
 create mode 100644 drivers/gpio/Makefile
 create mode 100644 drivers/gpio/pca953x.c
 create mode 100644 drivers/misc/ds4510.c
 create mode 100644 include/configs/XPEDITE5370.h
 create mode 100644 include/ds4510.h
 create mode 100644 include/pca953x.h

Initial support for NXP's 4 and 8 bit I2C gpio expanders (eg pca9537, pca9557, etc). The CONFIG_PCA953X define enables support for the devices while the CONFIG_CMD_PCA953X define enables the pca953x command. The CONFIG_CMD_PCA953X_INFO define enables an 'info' sub-command which provides summary information for the given pca953x device.

---
 Makefile               |    2 +
 README                 |    9 ++
 drivers/gpio/Makefile  |   47 ++++++++++
 drivers/gpio/pca953x.c |  227 ++++++++++++++++++++++++++++++++++++++++++++++++
 include/pca953x.h      |   39 ++++++++
 5 files changed, 324 insertions(+), 0 deletions(-)
 create mode 100644 drivers/gpio/Makefile
 create mode 100644 drivers/gpio/pca953x.c
 create mode 100644 include/pca953x.h

index fd521b6..0c5dd61 100644
@@ -221,6 +221,7 @@ drivers/bios_emulator/libatibiosemu.a
 LIBS += drivers/block/libblock.a
 LIBS += drivers/dma/libdma.a
 LIBS += drivers/fpga/libfpga.a
+LIBS += drivers/gpio/libgpio.a
 LIBS += drivers/hwmon/libhwmon.a
 LIBS += drivers/i2c/libi2c.a
 LIBS += drivers/input/libinput.a

@@ -396,6 +397,7 @@ TAG_SUBDIRS += disk
 TAG_SUBDIRS += common
 TAG_SUBDIRS += drivers/bios_emulator
 TAG_SUBDIRS += drivers/block
+TAG_SUBDIRS += drivers/gpio
 TAG_SUBDIRS += drivers/hwmon
 TAG_SUBDIRS += drivers/i2c
 TAG_SUBDIRS += drivers/input

index 9455fa7..bca8061 100644
@@ -603,6 +603,8 @@ The following options need to be configured:
 		CONFIG_CMD_MII		* MII utility commands
 		CONFIG_CMD_NAND		* NAND support
 		CONFIG_CMD_NET		  bootp, tftpboot, rarpboot
+		CONFIG_CMD_PCA953X	* PCA953x I2C gpio commands
+		CONFIG_CMD_PCA953X_INFO	* PCA953x I2C gpio info command
 		CONFIG_CMD_PCI		* pciinfo
 		CONFIG_CMD_PCMCIA		* PCMCIA support
 		CONFIG_CMD_PING		* send ICMP ECHO_REQUEST to network

@@ -680,6 +682,13 @@ The following options need to be configured:
 		Note that if the RTC uses I2C, then the I2C interface
 		must also be configured. See I2C Support, below.
 
+- GPIO Support:
+		CONFIG_PCA953X		- use NXP's PCA953X series I2C GPIO
+		CONFIG_PCA953X_INFO	- enable pca953x info command
+
+		Note that if the GPIO device uses I2C, then the I2C interface
+		must also be configured. See I2C Support, below.
+
 - Timestamp Support:
 
 		When CONFIG_TIMESTAMP is selected, the timestamp

new file mode 100644
index 0000000..6c2b58c
@@ -0,0 +1,39 @@
+/*
+ * Copyright 2008 Extreme Engineering Solutions, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __PCA953X_H_
+#define __PCA953X_H_
+
+#define PCA953X_IN		0x00
+#define PCA953X_OUT		0x01
+#define PCA953X_POL		0x02
+#define PCA953X_CONF		0x03
+
+#define PCA953X_OUT_LOW		0
+#define PCA953X_OUT_HIGH	1
+#define PCA953X_POL_NORMAL	0
+#define PCA953X_POL_INVERT	1
+#define PCA953X_DIR_OUT		0
+#define PCA953X_DIR_IN		1
+
+int pca953x_set_val(u8 chip, uint mask, uint data);
+int pca953x_set_pol(u8 chip, uint mask, uint data);
+int pca953x_set_dir(u8 chip, uint mask, uint data);
+int pca953x_get_val(u8 chip);
+
+#endif /* __PCA953X_H_ */

1.6.0.2.GIT

Initial support for the DS4510, a CPU supervisor with integrated EEPROM, SRAM, and 4 programmable non-volatile GPIO pins. The CONFIG_DS4510 define enables support for the device while the CONFIG_CMD_DS4510 define enables the ds4510 command. The additional CONFIG_DS4510_INFO, CONFIG_DS4510_MEM, and CONFIG_DS4510_RST defines add additional sub-commands to the ds4510 command when defined.

---
 README                |    4 +
 drivers/misc/Makefile |    1 +
 drivers/misc/ds4510.c |  424 +++++++++++++++++++++++++++++++++++++++++++++++++
 include/ds4510.h      |   75 +++++++++
 4 files changed, 504 insertions(+), 0 deletions(-)
 create mode 100644 drivers/misc/ds4510.c
 create mode 100644 include/ds4510.h

index bca8061..cea057d 100644
@@ -574,6 +574,10 @@ The following options need to be configured:
 		CONFIG_CMD_DHCP		* DHCP support
 		CONFIG_CMD_DIAG		* Diagnostics
 		CONFIG_CMD_DOC		* Disk-On-Chip Support
+		CONFIG_CMD_DS4510	* ds4510 I2C gpio commands
+		CONFIG_CMD_DS4510_INFO	* ds4510 I2C info command
+		CONFIG_CMD_DS4510_MEM	* ds4510 I2C eeprom/sram commansd
+		CONFIG_CMD_DS4510_RST	* ds4510 I2C rst command
 		CONFIG_CMD_DTT		* Digital Therm and Thermostat
 		CONFIG_CMD_ECHO		  echo arguments
 		CONFIG_CMD_EEPROM	* EEPROM read/write support

index 01e0f39..ea2bf87 100644
@@ -26,6 +26,7 @@ include $(TOPDIR)/config.mk
 LIB	:= $(obj)libmisc.a
 
 COBJS-$(CONFIG_ALI152X) += ali512x.o
+COBJS-$(CONFIG_DS4510)  += ds4510.o
 COBJS-$(CONFIG_FSL_LAW) += fsl_law.o
 COBJS-$(CONFIG_NS87308) += ns87308.o
 COBJS-$(CONFIG_STATUS_LED) += status_led.o

1.6.0.2.GIT

Initial support for Extreme Engineering Solutions XPedite5370 - a MPC8572-based 3U VPX single board computer with a PMC/XMC site.

---
 MAINTAINERS                         |    3 +
 MAKEALL                             |    1 +
 Makefile                            |    3 +
 board/xes/common/Makefile           |   56 ++++
 board/xes/common/fsl_8572_clk.c     |   51 +++
 board/xes/common/fsl_85xx_ddr.c     |   93 ++++++
 board/xes/common/fsl_85xx_pci.c     |  265 ++++++++++++++++
 board/xes/xpedite5370/Makefile      |   45 +++
 board/xes/xpedite5370/config.mk     |   35 ++
 board/xes/xpedite5370/ddr.c         |  270 ++++++++++++++++
 board/xes/xpedite5370/law.c         |   54 ++++
 board/xes/xpedite5370/tlb.c         |   94 ++++++
 board/xes/xpedite5370/u-boot.lds    |  145 +++++++++
 board/xes/xpedite5370/xpedite5370.c |  128 ++++++++
 include/configs/XPEDITE5370.h       |  589 +++++++++++++++++++++++++++++++++++
 15 files changed, 1832 insertions(+), 0 deletions(-)
 create mode 100644 board/xes/common/Makefile
 create mode 100644 board/xes/common/fsl_8572_clk.c
 create mode 100644 board/xes/common/fsl_85xx_ddr.c
 create mode 100644 board/xes/common/fsl_85xx_pci.c
 create mode 100644 board/xes/xpedite5370/Makefile
 create mode 100644 board/xes/xpedite5370/config.mk
 create mode 100644 board/xes/xpedite5370/ddr.c
 create mode 100644 board/xes/xpedite5370/law.c
 create mode 100644 board/xes/xpedite5370/tlb.c
 create mode 100644 board/xes/xpedite5370/u-boot.lds
 create mode 100644 board/xes/xpedite5370/xpedite5370.c
 create mode 100644 include/configs/XPEDITE5370.h

index 127604b..ee98824 100644
@@ -411,6 +411,9 @@ Rune Torgersen <[email protected]>
 
 	MPC8266ADS	MPC8266
 
+Peter Tyser <[email protected]>
+
+	XPEDITE5370	MPC8572
 
 David Updegraff <[email protected]>
 

index dbed268..1328514 100755
@@ -376,6 +376,7 @@ LIST_85xx="		\
 	TQM8548		\
 	TQM8555		\
 	TQM8560		\
+	XPEDITE5370	\
 "
 
 #########################################################################

index 0c5dd61..ae3ec22 100644
@@ -2454,6 +2454,9 @@ TQM8560_config:		unconfig
 	echo "#define CONFIG_BOARDNAME \"TQM$${CTYPE}\"">>$(obj)include/config.h;
 	@$(MKCONFIG) -a TQM85xx ppc mpc85xx tqm85xx tqc
 
+XPEDITE5370_config:	unconfig
+	@$(MKCONFIG) $(@:_config=) ppc mpc85xx xpedite5370 xes
+
 #########################################################################
 ## MPC86xx Systems
 #########################################################################

new file mode 100644
index 0000000..39469b2
@@ -0,0 +1,35 @@
+#
+# Copyright 2008 Extreme Engineering Solutions, Inc.
+# Copyright 2007-2008 Freescale Semiconductor, Inc.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# xpedite5370 board
+#
+ifndef TEXT_BASE
+TEXT_BASE = 0xfff80000
+endif
+
+PLATFORM_RELFLAGS += -mrelocatable
+
+PLATFORM_CPPFLAGS += -DCONFIG_E500=1
+PLATFORM_CPPFLAGS += -DCONFIG_MPC85xx=1
+PLATFORM_CPPFLAGS += -DCONFIG_MPC8572=1

1.6.0.2.GIT

Dear Peter Tyser,

Applied, thanks.

Best regards,

Wolfgang Denk

DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
The only person who always got his work done by Friday
                                                 was Robinson Crusoe.