Loongson: YeeLoong: add platform drivers

new file mode 100644
index 0000000..4fccb5d
@@ -0,0 +1,191 @@
+/*
+ * KB3310B Embedded Controller
+ *
+ *  Copyright (C) 2008 Lemote Inc.
+ *  Author: liujl <[email protected]>, 2008-03-14
+ *  Copyright (C) 2009 Lemote Inc.
+ *  Author: Wu Zhangjin <[email protected]>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef _EC_KB3310B_H
+#define _EC_KB3310B_H
+
+extern unsigned char ec_read(unsigned short addr);
+extern void ec_write(unsigned short addr, unsigned char val);
+extern int ec_query_seq(unsigned char cmd);
+extern int ec_query_event_num(void);
+extern int ec_get_event_num(void);
+
+typedef int (*sci_handler) (int status);
+extern sci_handler yeeloong_report_lid_status;
+
+#define SCI_IRQ_NUM 0x0A
+
+/*
+ * The following registers are determined by the EC index configuration.
+ * 1, fill the PORT_HIGH as EC register high part.
+ * 2, fill the PORT_LOW as EC register low part.
+ * 3, fill the PORT_DATA as EC register write data or get the data from it.
+ */
+#define	EC_IO_PORT_HIGH	0x0381
+#define	EC_IO_PORT_LOW	0x0382
+#define	EC_IO_PORT_DATA	0x0383
+
+/*
+ * EC delay time is 500us for register and status access
+ */
+#define	EC_REG_DELAY	500	/* unit : us */
+#define	EC_CMD_TIMEOUT	0x1000
+
+/*
+ * EC access port for SCI communication
+ */
+#define	EC_CMD_PORT		0x66
+#define	EC_STS_PORT		0x66
+#define	EC_DAT_PORT		0x62
+#define	CMD_INIT_IDLE_MODE	0xdd
+#define	CMD_EXIT_IDLE_MODE	0xdf
+#define	CMD_INIT_RESET_MODE	0xd8
+#define	CMD_REBOOT_SYSTEM	0x8c
+#define	CMD_GET_EVENT_NUM	0x84
+#define	CMD_PROGRAM_PIECE	0xda
+
+/* Temperature & Fan registers */
+#define	REG_TEMPERATURE_VALUE	0xF458
+#define	REG_FAN_AUTO_MAN_SWITCH 0xF459
+#define	BIT_FAN_AUTO		0
+#define	BIT_FAN_MANUAL		1
+#define	REG_FAN_CONTROL		0xF4D2
+#define	BIT_FAN_CONTROL_ON	(1 << 0)
+#define	BIT_FAN_CONTROL_OFF	(0 << 0)
+#define	REG_FAN_STATUS		0xF4DA
+#define	BIT_FAN_STATUS_ON	(1 << 0)
+#define	BIT_FAN_STATUS_OFF	(0 << 0)
+#define	REG_FAN_SPEED_HIGH	0xFE22
+#define	REG_FAN_SPEED_LOW	0xFE23
+#define	REG_FAN_SPEED_LEVEL	0xF4CC
+/* Fan speed divider */
+#define	FAN_SPEED_DIVIDER	480000	/* (60*1000*1000/62.5/2)*/
+
+/* Battery registers */
+#define	REG_BAT_DESIGN_CAP_HIGH		0xF77D
+#define	REG_BAT_DESIGN_CAP_LOW		0xF77E
+#define	REG_BAT_FULLCHG_CAP_HIGH	0xF780
+#define	REG_BAT_FULLCHG_CAP_LOW		0xF781
+#define	REG_BAT_DESIGN_VOL_HIGH		0xF782
+#define	REG_BAT_DESIGN_VOL_LOW		0xF783
+#define	REG_BAT_CURRENT_HIGH		0xF784
+#define	REG_BAT_CURRENT_LOW		0xF785
+#define	REG_BAT_VOLTAGE_HIGH		0xF786
+#define	REG_BAT_VOLTAGE_LOW		0xF787
+#define	REG_BAT_TEMPERATURE_HIGH	0xF788
+#define	REG_BAT_TEMPERATURE_LOW		0xF789
+#define	REG_BAT_RELATIVE_CAP_HIGH	0xF492
+#define	REG_BAT_RELATIVE_CAP_LOW	0xF493
+#define	REG_BAT_VENDOR			0xF4C4
+#define	FLAG_BAT_VENDOR_SANYO		0x01
+#define	FLAG_BAT_VENDOR_SIMPLO		0x02
+#define	REG_BAT_CELL_COUNT		0xF4C6
+#define	FLAG_BAT_CELL_3S1P		0x03
+#define	FLAG_BAT_CELL_3S2P		0x06
+#define	REG_BAT_CHARGE			0xF4A2
+#define	FLAG_BAT_CHARGE_DISCHARGE	0x01
+#define	FLAG_BAT_CHARGE_CHARGE		0x02
+#define	FLAG_BAT_CHARGE_ACPOWER		0x00
+#define	REG_BAT_STATUS			0xF4B0
+#define	BIT_BAT_STATUS_LOW		(1 << 5)
+#define	BIT_BAT_STATUS_DESTROY		(1 << 2)
+#define	BIT_BAT_STATUS_FULL		(1 << 1)
+#define	BIT_BAT_STATUS_IN		(1 << 0)
+#define	REG_BAT_CHARGE_STATUS		0xF4B1
+#define	BIT_BAT_CHARGE_STATUS_OVERTEMP	(1 << 2)
+#define	BIT_BAT_CHARGE_STATUS_PRECHG	(1 << 1)
+#define	REG_BAT_STATE			0xF482
+#define	BIT_BAT_STATE_CHARGING		(1 << 1)
+#define	BIT_BAT_STATE_DISCHARGING	(1 << 0)
+#define	REG_BAT_POWER			0xF440
+#define	BIT_BAT_POWER_S3		(1 << 2)
+#define	BIT_BAT_POWER_ON		(1 << 1)
+#define	BIT_BAT_POWER_ACIN		(1 << 0)
+
+/* Audio: rd/wr */
+#define	REG_AUDIO_VOLUME	0xF46C
+#define	REG_AUDIO_MUTE		0xF4E7
+#define	REG_AUDIO_BEEP		0xF4D0
+/* USB port power or not: rd/wr */
+#define	REG_USB0_FLAG		0xF461
+#define	REG_USB1_FLAG		0xF462
+#define	REG_USB2_FLAG		0xF463
+#define	BIT_USB_FLAG_ON		1
+#define	BIT_USB_FLAG_OFF	0
+/* LID */
+#define	REG_LID_DETECT		0xF4BD
+#define	BIT_LID_DETECT_ON	1
+#define	BIT_LID_DETECT_OFF	0
+/* CRT */
+#define	REG_CRT_DETECT		0xF4AD
+#define	BIT_CRT_DETECT_PLUG	1
+#define	BIT_CRT_DETECT_UNPLUG	0
+/* LCD backlight brightness adjust: 9 levels */
+#define	REG_DISPLAY_BRIGHTNESS	0xF4F5
+/* Black screen Status */
+#define	BIT_DISPLAY_LCD_ON	1
+#define	BIT_DISPLAY_LCD_OFF	0
+/* LCD backlight control: off/restore */
+#define	REG_BACKLIGHT_CTRL	0xF7BD
+#define	BIT_BACKLIGHT_ON	1
+#define	BIT_BACKLIGHT_OFF	0
+/* Reset the machine auto-clear: rd/wr */
+#define	REG_RESET		0xF4EC
+#define	BIT_RESET_ON		1
+/* Light the led: rd/wr */
+#define	REG_LED			0xF4C8
+#define	BIT_LED_RED_POWER	(1 << 0)
+#define	BIT_LED_ORANGE_POWER	(1 << 1)
+#define	BIT_LED_GREEN_CHARGE	(1 << 2)
+#define	BIT_LED_RED_CHARGE	(1 << 3)
+#define	BIT_LED_NUMLOCK		(1 << 4)
+/* Test led mode, all led on/off */
+#define	REG_LED_TEST		0xF4C2
+#define	BIT_LED_TEST_IN		1
+#define	BIT_LED_TEST_OUT	0
+/* Camera on/off */
+#define	REG_CAMERA_STATUS	0xF46A
+#define	BIT_CAMERA_STATUS_ON	1
+#define	BIT_CAMERA_STATUS_OFF	0
+#define	REG_CAMERA_CONTROL	0xF7B7
+#define	BIT_CAMERA_CONTROL_OFF	0
+#define	BIT_CAMERA_CONTROL_ON	1
+/* Wlan Status */
+#define	REG_WLAN		0xF4FA
+#define	BIT_WLAN_ON		1
+#define	BIT_WLAN_OFF		0
+#define	REG_DISPLAY_LCD		0xF79F
+
+/* SCI Event Number from EC */
+enum {
+	EVENT_LID = 0x23,	/*  Turn on/off LID */
+	EVENT_DISPLAY_TOGGLE,	/*  Fn+F3 for display switch */
+	EVENT_SLEEP,		/*  Fn+F1 for entering sleep mode */
+	EVENT_OVERTEMP,		/*  Over-temperature happened */
+	EVENT_CRT_DETECT,	/*  CRT is connected */
+	EVENT_CAMERA,		/*  Camera on/off */
+	EVENT_USB_OC2,		/*  USB2 Over Current occurred */
+	EVENT_USB_OC0,		/*  USB0 Over Current occurred */
+	EVENT_BLACK_SCREEN,	/*  Turn on/off backlight */
+	EVENT_AUDIO_MUTE,	/*  Mute on/off */
+	EVENT_DISPLAY_BRIGHTNESS,/* LCD backlight brightness adjust */
+	EVENT_AC_BAT,		/*  AC & Battery relative issue */
+	EVENT_AUDIO_VOLUME,	/*  Volume adjust */
+	EVENT_WLAN,		/*  Wlan on/off */
+};
+
+#define EVENT_START	EVENT_LID
+#define EVENT_END	EVENT_WLAN
+
+#endif /* !_EC_KB3310B_H */

index 4d84111..734d2d0 100644
@@ -14,7 +14,7 @@
 #include <linux/spinlock.h>
 #include <linux/delay.h>
 
-#include "ec_kb3310b.h"
+#include <ec_kb3310b.h>
 
 static DEFINE_SPINLOCK(index_access_lock);
 static DEFINE_SPINLOCK(port_access_lock);

@@ -76,12 +76,9 @@ int ec_query_seq(unsigned char cmd)
 	}
 
 	if (timeout <= 0) {
-		printk(KERN_ERR "%s: deadable error : timeout...\n", __func__);
+		pr_err("%s: deadable error : timeout...\n", __func__);
 		ret = -EINVAL;
-	} else
-		printk(KERN_INFO
-			   "(%x/%d)ec issued command %d status : 0x%x\n",
-			   timeout, EC_CMD_TIMEOUT - timeout, cmd, status);
+	}
 
 	spin_unlock_irqrestore(&port_access_lock, flags);
 

@@ -118,8 +115,7 @@ int ec_get_event_num(void)
 		udelay(EC_REG_DELAY);
 	}
 	if (timeout <= 0) {
-		pr_info("%s: get event number timeout.\n", __func__);
-
+		pr_err("%s: get event number timeout.\n", __func__);
 		return -EINVAL;
 	}
 	value = inb(EC_DAT_PORT);

188 lines not on this page · raw message

new file mode 100644
index 0000000..0e7b27d
@@ -0,0 +1,40 @@
+/*
+ * Copyright (C) 2009 Lemote Inc.
+ * Author: Wu Zhangjin, [email protected]
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/err.h>
+#include <linux/platform_device.h>
+
+#include <asm/bootinfo.h>
+
+static struct platform_device yeeloong_pdev = {
+	.name = "yeeloong_laptop",
+	.id = -1,
+};
+
+static int __init lemote2f_platform_init(void)
+{
+	struct platform_device *pdev = NULL;
+
+	switch (mips_machtype) {
+	case MACH_LEMOTE_YL2F89:
+		pdev = &yeeloong_pdev;
+		break;
+	default:
+		break;
+
+	}
+
+	if (pdev != NULL)
+		return platform_device_register(pdev);
+
+	return -ENODEV;
+}
+
+arch_initcall(lemote2f_platform_init);

index d7af2e6..0d5698a 100644
@@ -23,7 +23,7 @@
 #include <loongson.h>
 
 #include <cs5536/cs5536_mfgpt.h>
-#include "ec_kb3310b.h"
+#include <ec_kb3310b.h>
 
 #define I8042_KBD_IRQ		1
 #define I8042_CTR_KBDINT	0x01

@@ -100,7 +100,7 @@ int wakeup_loongson(void)
 	if (irq < 0)
 		return 0;
 
-	printk(KERN_INFO "%s: irq = %d\n", __func__, irq);
+	pr_info("%s: irq = %d\n", __func__, irq);
 
 	if (irq == I8042_KBD_IRQ)
 		return 1;

index 51d1a60..4627659 100644
@@ -20,7 +20,7 @@
 #include <loongson.h>
 
 #include <cs5536/cs5536.h>
-#include "ec_kb3310b.h"
+#include <ec_kb3310b.h>
 
 static void reset_cpu(void)
 {

60 lines not on this page · raw message

98 lines not on this page · raw message

142 lines not on this page · raw message

240 lines not on this page · raw message

162 lines not on this page · raw message

index f8907da..baf3e81 100644
@@ -512,6 +512,39 @@ static void yeeloong_vo_exit(void)
 	}
 }
 
+#ifdef CONFIG_PM
+static void usb_ports_set(int status)
+{
+	status = !!status;
+
+	ec_write(REG_USB0_FLAG, status);
+	ec_write(REG_USB1_FLAG, status);
+	ec_write(REG_USB2_FLAG, status);
+}
+
+static int yeeloong_suspend(struct device *dev)
+
+{
+	yeeloong_lcd_vo_set(BIT_DISPLAY_LCD_OFF);
+	yeeloong_crt_vo_set(BIT_CRT_DETECT_UNPLUG);
+	usb_ports_set(BIT_USB_FLAG_OFF);
+
+	return 0;
+}
+
+static int yeeloong_resume(struct device *dev)
+{
+	yeeloong_lcd_vo_set(BIT_DISPLAY_LCD_ON);
+	yeeloong_crt_vo_set(BIT_CRT_DETECT_PLUG);
+	usb_ports_set(BIT_USB_FLAG_ON);
+
+	return 0;
+}
+
+static const SIMPLE_DEV_PM_OPS(yeeloong_pm_ops, yeeloong_suspend,
+	yeeloong_resume);
+#endif
+
 static struct platform_device_id platform_device_ids[] = {
 	{
 		.name = "yeeloong_laptop",

@@ -523,9 +556,12 @@ MODULE_DEVICE_TABLE(platform, platform_device_ids);
 
 static struct platform_driver platform_driver = {
 	.driver = {
-		   .name = "yeeloong_laptop",
-		   .owner = THIS_MODULE,
-		   },
+		.name = "yeeloong_laptop",
+		.owner = THIS_MODULE,
+#ifdef CONFIG_PM
+		.pm = &yeeloong_pm_ops,
+#endif
+	},
 	.id_table = platform_device_ids,
 };
 

index ee8bc83..13e208e 100644
@@ -43,6 +43,12 @@ static inline void prom_init_uart_base(void)
 #endif
 }
 
+/*
+ * Copy kernel command line from arcs_cmdline
+ */
+#include <asm/setup.h>
+extern char loongson_cmdline[COMMAND_LINE_SIZE];
+
 /* irq operation functions */
 extern void bonito_irqdispatch(void);
 extern void __init bonito_irq_init(void);

index 7ad47f2..617faee 100644
@@ -17,6 +17,7 @@
  * Free Software Foundation;  either version 2 of the  License, or (at your
  * option) any later version.
  */
+#include <linux/module.h>
 #include <asm/bootinfo.h>
 
 #include <loongson.h>

@@ -25,6 +26,10 @@ int prom_argc;
 /* pmon passes arguments in 32bit pointers */
 int *_prom_argv;
 
+/* the kernel command line copied from arcs_cmdline */
+char loongson_cmdline[COMMAND_LINE_SIZE];
+EXPORT_SYMBOL(loongson_cmdline);
+
 void __init prom_init_cmdline(void)
 {
 	int i;

@@ -51,4 +56,7 @@ void __init prom_init_cmdline(void)
 		strcat(arcs_cmdline, " root=/dev/hda1");
 
 	prom_init_machtype();
+
+	/* copy arcs_cmdline into loongson_cmdline */
+	strncpy(loongson_cmdline, arcs_cmdline, COMMAND_LINE_SIZE);
 }

436 lines not on this page · raw message