Skip to contentSkip to conversation

framebuffer work (especially i.MX)

PATCH Superseded Daniel Mierswa 3 participants 7 messages Jan 14, 2013

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 framebuffer work (especially i.MX)

I provided a couple of patches to make the framebuffer device on our platform work. At least incohately. As this is my first patch series provided to the project I'm very unsure about the quality and would greatly appreciate your input. Especially because it introduces platform specific code in the video driver where it was removed not too long ago.

Daniel Mierswa (4):
i.MX21: Add periph. clock register name macros i.MX21/27: don't enable lcd bus clocks too early i.MX27: fix shift amount for PCCR1_PERCLK3_EN
graphic_utils: always initialize offscreenbuf member

 arch/arm/mach-imx/clk-imx21.c               | 61 +++++++++++++++++++++++++----
 arch/arm/mach-imx/clk-imx27.c               | 16 +++++---
 arch/arm/mach-imx/include/mach/imx21-regs.h |  6 ---
 drivers/video/imx.c                         | 51 ++++++++++++++++++++----
 lib/gui/graphic_utils.c                     |  2 +
 5 files changed, 110 insertions(+), 26 deletions(-)
Signature · 7 lines
1.8.1


_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
#1 lore raw

PATCH 1/4 i.MX21: Add periph. clock register name macros

Also put those names solely in the .c file as it's done with the i.MX27 code.

---
 arch/arm/mach-imx/clk-imx21.c               | 56 +++++++++++++++++++++++++----
 arch/arm/mach-imx/include/mach/imx21-regs.h |  6 ----
 2 files changed, 50 insertions(+), 12 deletions(-)
arch/arm/mach-imx/clk-imx21.c +50 -6
index 9e7af81..784951d 100644
@@ -45,6 +45,48 @@
 #define CCM_PMCOUNT		0x30
 #define CCM_WKGDCTL		0x34
 
+#define PCCR0_UART1_EN		(1 << 0)
+#define PCCR0_UART2_EN		(1 << 1)
+#define PCCR0_UART3_EN		(1 << 2)
+#define PCCR0_UART4_EN		(1 << 3)
+#define PCCR0_CSPI1_EN		(1 << 4)
+#define PCCR0_CSPI2_EN		(1 << 5)
+#define PCCR0_SSI1_EN		(1 << 6)
+#define PCCR0_SSI2_EN		(1 << 7)
+#define PCCR0_FIRI_EN		(1 << 8)
+#define PCCR0_SDHC1_EN		(1 << 9)
+#define PCCR0_SDHC2_EN		(1 << 10)
+#define PCCR0_GPIO_EN		(1 << 11)
+#define PCCR0_I2C_EN		(1 << 12)
+#define PCCR0_DMA_EN		(1 << 13)
+#define PCCR0_USBOTG_EN		(1 << 14)
+#define PCCR0_EMMA_EN		(1 << 15)
+#define PCCR0_SSI2_BAUD_EN	(1 << 16)
+#define PCCR0_SSI1_BAUD_EN	(1 << 17)
+#define PCCR0_PERCLK3_EN	(1 << 18)
+#define PCCR0_NFC_EN		(1 << 19)
+#define PCCR0_FRI_BAUD_EN	(1 << 20)
+#define PCCR0_SLDC_EN		(1 << 21)
+#define PCCR0_PERCLK4_EN	(1 << 22)
+#define PCCR0_HCLK_BMI_EN	(1 << 23)
+#define PCCR0_HCLK_USBOTG_EN	(1 << 24)
+#define PCCR0_HCLK_SLCDC_EN	(1 << 25)
+#define PCCR0_HCLK_LCDC_EN	(1 << 26)
+#define PCCR0_HCLK_EMMA_EN	(1 << 27)
+#define PCCR0_HCLK_BROM_EN	(1 << 28)
+#define PCCR0_HCLK_DMA_EN	(1 << 30)
+#define PCCR0_HCLK_CSI_EN	(1 << 31)
+
+#define PCCR1_CSPI3_EN	(1 << 23)
+#define PCCR1_WDT_EN	(1 << 24)
+#define PCCR1_GPT1_EN	(1 << 25)
+#define PCCR1_GPT2_EN	(1 << 26)
+#define PCCR1_GPT3_EN	(1 << 27)
+#define PCCR1_PWM_EN	(1 << 28)
+#define PCCR1_RTC_EN	(1 << 29)
+#define PCCR1_KPP_EN	(1 << 30)
+#define PCCR1_OWIRE_EN	(1 << 31)
+
 enum imx21_clks {
 	ckil, ckih, fpm, mpll_sel, spll_sel, mpll, spll, fclk, hclk, ipg, per1,
 	per2, per3, per4, usb_div, nfc_div, lcdc_per_gate, clk_max
@@ -70,14 +112,16 @@ static int imx21_ccm_probe(struct device_d *dev)
 
 	base = dev_request_mem_region(dev, 0);
 
-	writel((1 << 0) | (1 << 1) | (1 << 2) | (1 << 3) | (1 << 4) | (1 << 5) |
-			(1 << 9) | (1 << 10) | (1 << 11) | (1 << 12) |
-			(1 << 13) | (1 << 14) | (1 << 19) | (1 << 22) |
-			(1 << 24) | (1 << 26) |	(1 << 30),
+	writel(PCCR0_UART1_EN | PCCR0_UART2_EN | PCCR0_UART3_EN | PCCR0_UART4_EN |
+			PCCR0_CSPI1_EN | PCCR0_CSPI2_EN | PCCR0_SDHC1_EN |
+			PCCR0_SDHC2_EN | PCCR0_GPIO_EN | PCCR0_I2C_EN | PCCR0_DMA_EN |
+			PCCR0_USBOTG_EN | PCCR0_NFC_EN | PCCR0_PERCLK4_EN |
+			PCCR0_HCLK_USBOTG_EN | PCCR0_HCLK_LCDC_EN | PCCR0_HCLK_DMA_EN,
 			base + CCM_PCCR0);
 
-	writel((1 << 23) | (1 << 24) | (1 << 25) | (1 << 26) | (1 << 27) |
-			(1 << 28) | (1 << 29) | (1 << 30) | (1 << 31),
+	writel(PCCR1_CSPI3_EN | PCCR1_WDT_EN | PCCR1_GPT1_EN | PCCR1_GPT2_EN |
+			PCCR1_GPT3_EN | PCCR1_PWM_EN | PCCR1_RTC_EN | PCCR1_KPP_EN |
+			PCCR1_OWIRE_EN,
 			base + CCM_PCCR1);
 
 	clks[ckil] = clk_fixed("ckil", lref);
arch/arm/mach-imx/include/mach/imx21-regs.h +0 -6
index 1c4b550..87bd99c 100644
@@ -129,12 +129,6 @@
 #define MX21_MPCTL1_BRMO	(1 << 6)
 #define MX21_MPCTL1_LF		(1 << 15)
 
-#define MX21_PCCR0_PERCLK3_EN	(1 << 18)
-#define MX21_PCCR0_NFC_EN	(1 << 19)
-#define MX21_PCCR0_HCLK_LCDC_EN	(1 << 26)
-
-#define MX21_PCCR1_GPT1_EN	(1 << 25)
-
 #define MX21_CCSR_32K_SR	(1 << 15)
 
 #endif /* _IMX21_REGS_H */
Signature · 7 lines
1.8.1


_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
#2 lore raw

PATCH 2/4 i.MX21/27: don't enable lcd bus clocks too early

In reply to Daniel Mierswa

On the MX27 based board phycard-i.MX27 the display won't properly come up.
Before removing imx-regs.h and the code that sets the register in the i.MX video driver, the PCCR registers were set _after_ the screen start (LSSAR) was set.
This restores that old behaviour and makes the display come up properly again.
I did not have a chance to test this on any other i.MX27 or i.MX21 hardware though I assume that the "old" order is required there too.

---
 arch/arm/mach-imx/clk-imx21.c |  7 ++++--
 arch/arm/mach-imx/clk-imx27.c | 14 +++++++-----
 drivers/video/imx.c           | 51 +++++++++++++++++++++++++++++++++++++------
 3 files changed, 58 insertions(+), 14 deletions(-)
arch/arm/mach-imx/clk-imx21.c +5 -2
index 784951d..7404177 100644
@@ -89,7 +89,8 @@
 
 enum imx21_clks {
 	ckil, ckih, fpm, mpll_sel, spll_sel, mpll, spll, fclk, hclk, ipg, per1,
-	per2, per3, per4, usb_div, nfc_div, lcdc_per_gate, clk_max
+	per2, per3, per4, usb_div, nfc_div, lcdc_per_gate, lcdc_ahb_gate,
+	clk_max
 };
 
 static struct clk *clks[clk_max];
@@ -116,7 +117,7 @@ static int imx21_ccm_probe(struct device_d *dev)
 			PCCR0_CSPI1_EN | PCCR0_CSPI2_EN | PCCR0_SDHC1_EN |
 			PCCR0_SDHC2_EN | PCCR0_GPIO_EN | PCCR0_I2C_EN | PCCR0_DMA_EN |
 			PCCR0_USBOTG_EN | PCCR0_NFC_EN | PCCR0_PERCLK4_EN |
-			PCCR0_HCLK_USBOTG_EN | PCCR0_HCLK_LCDC_EN | PCCR0_HCLK_DMA_EN,
+			PCCR0_HCLK_USBOTG_EN | PCCR0_HCLK_DMA_EN,
 			base + CCM_PCCR0);
 
 	writel(PCCR1_CSPI3_EN | PCCR1_WDT_EN | PCCR1_GPT1_EN | PCCR1_GPT2_EN |
@@ -143,6 +144,7 @@ static int imx21_ccm_probe(struct device_d *dev)
 	clks[usb_div] = imx_clk_divider("usb_div", "spll", base + CCM_CSCR, 26, 3);
 	clks[nfc_div] = imx_clk_divider("nfc_div", "ipg", base + CCM_PCDR0, 12, 4);
 	clks[lcdc_per_gate] = imx_clk_gate("lcdc_per_gate", "per3", base + CCM_PCCR0, 18);
+	clks[lcdc_ahb_gate] = imx_clk_gate("lcdc_ahb_gate", "ahb", base + CCM_PCCR0, 26);
 
 	clkdev_add_physbase(clks[per1], MX21_GPT1_BASE_ADDR, NULL);
 	clkdev_add_physbase(clks[per1], MX21_GPT2_BASE_ADDR, NULL);
@@ -158,6 +160,7 @@ static int imx21_ccm_probe(struct device_d *dev)
 	clkdev_add_physbase(clks[ipg], MX21_SDHC1_BASE_ADDR, NULL);
 	clkdev_add_physbase(clks[ipg], MX21_SDHC2_BASE_ADDR, NULL);
 	clkdev_add_physbase(clks[lcdc_per_gate], MX21_LCDC_BASE_ADDR, NULL);
+	clkdev_add_physbase(clks[lcdc_ahb_gate], MX21_LCDC_BASE_ADDR, "ahb");
 
 	return 0;
 }
arch/arm/mach-imx/clk-imx27.c +9 -5
index 222d2a6..958495e 100644
@@ -93,7 +93,7 @@
 enum mx27_clks {
 	dummy, ckih, ckil, mpll, spll, mpll_main2, ahb, ipg, nfc_div, per1_div,
 	per2_div, per3_div, per4_div, usb_div, cpu_sel,	clko_sel, cpu_div, clko_div,
-	clko_en, lcdc_per_gate, clk_max
+	clko_en, lcdc_per_gate, lcdc_ahb_gate, lcdc_ipg_gate, clk_max
 };
 
 static struct clk *clks[clk_max];
@@ -136,7 +136,7 @@ static int imx27_ccm_probe(struct device_d *dev)
 	base = dev_request_mem_region(dev, 0);
 
 	writel(PCCR0_SDHC3_EN | PCCR0_SDHC2_EN | PCCR0_SDHC1_EN |
-			PCCR0_PWM_EN | PCCR0_KPP_EN | PCCR0_LCDC_EN | PCCR0_IIM_EN |
+			PCCR0_PWM_EN | PCCR0_KPP_EN | PCCR0_IIM_EN |
 			PCCR0_I2C2_EN | PCCR0_I2C1_EN | PCCR0_GPT6_EN | PCCR0_GPT5_EN |
 			PCCR0_GPT4_EN | PCCR0_GPT3_EN | PCCR0_GPT2_EN | PCCR0_GPT1_EN |
 			PCCR0_GPIO_EN | PCCR0_FEC_EN | PCCR0_CSPI3_EN | PCCR0_CSPI2_EN |
@@ -144,9 +144,9 @@ static int imx27_ccm_probe(struct device_d *dev)
 			base + CCM_PCCR0);
 
 	writel(PCCR1_NFC_BAUDEN | PCCR1_PERCLK4_EN | PCCR1_PERCLK2_EN | PCCR1_PERCLK1_EN |
-			PCCR1_HCLK_USB | PCCR1_HCLK_LCDC | PCCR1_HCLK_FEC | PCCR1_HCLK_EMI |
-			PCCR1_WDT_EN | PCCR1_USB_EN | PCCR1_UART6_EN | PCCR1_UART5_EN |
-			PCCR1_UART4_EN | PCCR1_UART3_EN | PCCR1_UART2_EN | PCCR1_UART1_EN,
+			PCCR1_HCLK_USB | PCCR1_HCLK_FEC | PCCR1_HCLK_EMI | PCCR1_WDT_EN |
+			PCCR1_USB_EN | PCCR1_UART6_EN | PCCR1_UART5_EN | PCCR1_UART4_EN |
+			PCCR1_UART3_EN | PCCR1_UART2_EN | PCCR1_UART1_EN,
 			base + CCM_PCCR1);
 
 	clks[dummy] = clk_fixed("dummy", 0);
@@ -180,6 +180,8 @@ static int imx27_ccm_probe(struct device_d *dev)
 		clks[cpu_div] = imx_clk_divider("cpu_div", "cpu_sel", base + CCM_CSCR, 13, 3);
 	clks[clko_div] = imx_clk_divider("clko_div", "clko_sel", base + CCM_PCDR0, 22, 3);
 	clks[lcdc_per_gate] = imx_clk_gate("lcdc_per_gate", "per3_div", base + CCM_PCCR1, 7);
+	clks[lcdc_ahb_gate] = imx_clk_gate("lcdc_ahb_gate", "ahb", base + CCM_PCCR1, 15);
+	clks[lcdc_ipg_gate] = imx_clk_gate("lcdc_ipg_gate", "ipg", base + CCM_PCCR0, 14);
 
 	clkdev_add_physbase(clks[per1_div], MX27_GPT1_BASE_ADDR, NULL);
 	clkdev_add_physbase(clks[per1_div], MX27_GPT2_BASE_ADDR, NULL);
@@ -202,6 +204,8 @@ static int imx27_ccm_probe(struct device_d *dev)
 	clkdev_add_physbase(clks[per2_div], MX27_SDHC2_BASE_ADDR, NULL);
 	clkdev_add_physbase(clks[per2_div], MX27_SDHC3_BASE_ADDR, NULL);
 	clkdev_add_physbase(clks[lcdc_per_gate], MX27_LCDC_BASE_ADDR, NULL);
+	clkdev_add_physbase(clks[lcdc_ahb_gate], MX27_LCDC_BASE_ADDR, "ahb");
+	clkdev_add_physbase(clks[lcdc_ipg_gate], MX27_LCDC_BASE_ADDR, "ipg");
 	clkdev_add_physbase(clks[ipg], MX27_FEC_BASE_ADDR, NULL);
 
 	return 0;
drivers/video/imx.c +44 -7

81 lines not on this page · raw message

Signature · 7 lines
1.8.1


_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
maintainer
#3 lore raw

Re: [PATCH 2/4] i.MX21/27: don't enable lcd bus clocks too early

Quoted 187 lines · Daniel Mierswa

On the MX27 based board phycard-i.MX27 the display won't properly come up.
Before removing imx-regs.h and the code that sets the register in the i.MX video driver, the PCCR registers were set _after_ the screen start (LSSAR) was set.
This restores that old behaviour and makes the display come up properly again.
I did not have a chance to test this on any other i.MX27 or i.MX21 hardware though I assume that the "old" order is required there too.

---
 arch/arm/mach-imx/clk-imx21.c |  7 ++++--
 arch/arm/mach-imx/clk-imx27.c | 14 +++++++-----
 drivers/video/imx.c           | 51 +++++++++++++++++++++++++++++++++++++------
 3 files changed, 58 insertions(+), 14 deletions(-)
arch/arm/mach-imx/clk-imx21.c +5 -2
index 784951d..7404177 100644
@@ -89,7 +89,8 @@
 
 enum imx21_clks {
 	ckil, ckih, fpm, mpll_sel, spll_sel, mpll, spll, fclk, hclk, ipg, per1,
-	per2, per3, per4, usb_div, nfc_div, lcdc_per_gate, clk_max
+	per2, per3, per4, usb_div, nfc_div, lcdc_per_gate, lcdc_ahb_gate,
+	clk_max
 };
 
 static struct clk *clks[clk_max];
@@ -116,7 +117,7 @@ static int imx21_ccm_probe(struct device_d *dev)
 			PCCR0_CSPI1_EN | PCCR0_CSPI2_EN | PCCR0_SDHC1_EN |
 			PCCR0_SDHC2_EN | PCCR0_GPIO_EN | PCCR0_I2C_EN | PCCR0_DMA_EN |
 			PCCR0_USBOTG_EN | PCCR0_NFC_EN | PCCR0_PERCLK4_EN |
-			PCCR0_HCLK_USBOTG_EN | PCCR0_HCLK_LCDC_EN | PCCR0_HCLK_DMA_EN,
+			PCCR0_HCLK_USBOTG_EN | PCCR0_HCLK_DMA_EN,
 			base + CCM_PCCR0);
 
 	writel(PCCR1_CSPI3_EN | PCCR1_WDT_EN | PCCR1_GPT1_EN | PCCR1_GPT2_EN |
@@ -143,6 +144,7 @@ static int imx21_ccm_probe(struct device_d *dev)
 	clks[usb_div] = imx_clk_divider("usb_div", "spll", base + CCM_CSCR, 26, 3);
 	clks[nfc_div] = imx_clk_divider("nfc_div", "ipg", base + CCM_PCDR0, 12, 4);
 	clks[lcdc_per_gate] = imx_clk_gate("lcdc_per_gate", "per3", base + CCM_PCCR0, 18);
+	clks[lcdc_ahb_gate] = imx_clk_gate("lcdc_ahb_gate", "ahb", base + CCM_PCCR0, 26);
 
 	clkdev_add_physbase(clks[per1], MX21_GPT1_BASE_ADDR, NULL);
 	clkdev_add_physbase(clks[per1], MX21_GPT2_BASE_ADDR, NULL);
@@ -158,6 +160,7 @@ static int imx21_ccm_probe(struct device_d *dev)
 	clkdev_add_physbase(clks[ipg], MX21_SDHC1_BASE_ADDR, NULL);
 	clkdev_add_physbase(clks[ipg], MX21_SDHC2_BASE_ADDR, NULL);
 	clkdev_add_physbase(clks[lcdc_per_gate], MX21_LCDC_BASE_ADDR, NULL);
+	clkdev_add_physbase(clks[lcdc_ahb_gate], MX21_LCDC_BASE_ADDR, "ahb");
 
 	return 0;
 }
arch/arm/mach-imx/clk-imx27.c +9 -5
index 222d2a6..958495e 100644
@@ -93,7 +93,7 @@
 enum mx27_clks {
 	dummy, ckih, ckil, mpll, spll, mpll_main2, ahb, ipg, nfc_div, per1_div,
 	per2_div, per3_div, per4_div, usb_div, cpu_sel,	clko_sel, cpu_div, clko_div,
-	clko_en, lcdc_per_gate, clk_max
+	clko_en, lcdc_per_gate, lcdc_ahb_gate, lcdc_ipg_gate, clk_max
 };
 
 static struct clk *clks[clk_max];
@@ -136,7 +136,7 @@ static int imx27_ccm_probe(struct device_d *dev)
 	base = dev_request_mem_region(dev, 0);
 
 	writel(PCCR0_SDHC3_EN | PCCR0_SDHC2_EN | PCCR0_SDHC1_EN |
-			PCCR0_PWM_EN | PCCR0_KPP_EN | PCCR0_LCDC_EN | PCCR0_IIM_EN |
+			PCCR0_PWM_EN | PCCR0_KPP_EN | PCCR0_IIM_EN |
 			PCCR0_I2C2_EN | PCCR0_I2C1_EN | PCCR0_GPT6_EN | PCCR0_GPT5_EN |
 			PCCR0_GPT4_EN | PCCR0_GPT3_EN | PCCR0_GPT2_EN | PCCR0_GPT1_EN |
 			PCCR0_GPIO_EN | PCCR0_FEC_EN | PCCR0_CSPI3_EN | PCCR0_CSPI2_EN |
@@ -144,9 +144,9 @@ static int imx27_ccm_probe(struct device_d *dev)
 			base + CCM_PCCR0);
 
 	writel(PCCR1_NFC_BAUDEN | PCCR1_PERCLK4_EN | PCCR1_PERCLK2_EN | PCCR1_PERCLK1_EN |
-			PCCR1_HCLK_USB | PCCR1_HCLK_LCDC | PCCR1_HCLK_FEC | PCCR1_HCLK_EMI |
-			PCCR1_WDT_EN | PCCR1_USB_EN | PCCR1_UART6_EN | PCCR1_UART5_EN |
-			PCCR1_UART4_EN | PCCR1_UART3_EN | PCCR1_UART2_EN | PCCR1_UART1_EN,
+			PCCR1_HCLK_USB | PCCR1_HCLK_FEC | PCCR1_HCLK_EMI | PCCR1_WDT_EN |
+			PCCR1_USB_EN | PCCR1_UART6_EN | PCCR1_UART5_EN | PCCR1_UART4_EN |
+			PCCR1_UART3_EN | PCCR1_UART2_EN | PCCR1_UART1_EN,
 			base + CCM_PCCR1);
 
 	clks[dummy] = clk_fixed("dummy", 0);
@@ -180,6 +180,8 @@ static int imx27_ccm_probe(struct device_d *dev)
 		clks[cpu_div] = imx_clk_divider("cpu_div", "cpu_sel", base + CCM_CSCR, 13, 3);
 	clks[clko_div] = imx_clk_divider("clko_div", "clko_sel", base + CCM_PCDR0, 22, 3);
 	clks[lcdc_per_gate] = imx_clk_gate("lcdc_per_gate", "per3_div", base + CCM_PCCR1, 7);
+	clks[lcdc_ahb_gate] = imx_clk_gate("lcdc_ahb_gate", "ahb", base + CCM_PCCR1, 15);
+	clks[lcdc_ipg_gate] = imx_clk_gate("lcdc_ipg_gate", "ipg", base + CCM_PCCR0, 14);
 
 	clkdev_add_physbase(clks[per1_div], MX27_GPT1_BASE_ADDR, NULL);
 	clkdev_add_physbase(clks[per1_div], MX27_GPT2_BASE_ADDR, NULL);
@@ -202,6 +204,8 @@ static int imx27_ccm_probe(struct device_d *dev)
 	clkdev_add_physbase(clks[per2_div], MX27_SDHC2_BASE_ADDR, NULL);
 	clkdev_add_physbase(clks[per2_div], MX27_SDHC3_BASE_ADDR, NULL);
 	clkdev_add_physbase(clks[lcdc_per_gate], MX27_LCDC_BASE_ADDR, NULL);
+	clkdev_add_physbase(clks[lcdc_ahb_gate], MX27_LCDC_BASE_ADDR, "ahb");
+	clkdev_add_physbase(clks[lcdc_ipg_gate], MX27_LCDC_BASE_ADDR, "ipg");
 	clkdev_add_physbase(clks[ipg], MX27_FEC_BASE_ADDR, NULL);
 
 	return 0;
drivers/video/imx.c +34 -7
index 8381690..18e1243 100644
@@ -138,7 +138,16 @@ struct imxfb_rgb {
 
 struct imxfb_info {
 	void __iomem		*regs;
-	struct clk		*clk;
+
+#if defined(CONFIG_ARCH_IMX21) || defined(CONFIG_ARCH_IMX27)
+	struct clk		*ahb_clk;
+#endif
+
+#ifdef CONFIG_ARCH_IMX27
+	struct clk		*ipg_clk;
+#endif
+
+	struct clk		*per_clk;
 
 	u_int			pcr;
 	u_int			pwmr;
@@ -252,7 +261,15 @@ static void imxfb_enable_controller(struct fb_info *info)
 
 	writel(RMCR_LCDC_EN, fbi->regs + LCDC_RMCR);
 
-	clk_enable(fbi->clk);
+#if defined(CONFIG_ARCH_IMX21) || defined(CONFIG_ARCH_IMX27)
+	clk_enable(fbi->ahb_clk);
+#endif
+
+#ifdef CONFIG_ARCH_IMX27
+	clk_enable(fbi->ipg_clk);
+#endif
+
+	clk_enable(fbi->per_clk);
 
 	if (fbi->enable)
 		fbi->enable(1);
@@ -267,7 +284,15 @@ static void imxfb_disable_controller(struct fb_info *info)
 
 	writel(0, fbi->regs + LCDC_RMCR);
 
-	clk_disable(fbi->clk);
+	clk_disable(fbi->per_clk);
+
+#ifdef CONFIG_ARCH_IMX27
+	clk_disable(fbi->ipg_clk);
+#endif
+
+#if defined(CONFIG_ARCH_IMX21) || defined(CONFIG_ARCH_IMX27)
+	clk_disable(fbi->ahb_clk);
+#endif
 }
 
 static void set_reg_overlay(struct fb_info *overlay)
@@ -335,7 +360,7 @@ static int imxfb_activate_var(struct fb_info *info)
 	writel(readl(fbi->regs + LCDC_CPOS) & ~(CPOS_CC0 | CPOS_CC1),
 		fbi->regs + LCDC_CPOS);
 
-	lcd_clk = clk_get_rate(fbi->clk);
+	lcd_clk = clk_get_rate(fbi->per_clk);
 
 	tmp = mode->pixclock * (unsigned long long)lcd_clk;
 
@@ -549,9 +574,21 @@ static int imxfb_probe(struct device_d *dev)
 	fbi = xzalloc(sizeof(*fbi));
 	info = &fbi->info;
 
-	fbi->clk = clk_get(dev, NULL);
-	if (IS_ERR(fbi->clk))
-		return PTR_ERR(fbi->clk);
+	fbi->per_clk = clk_get(dev, NULL);
+	if (IS_ERR(fbi->per_clk))
+		return PTR_ERR(fbi->per_clk);
+
+#if defined(CONFIG_ARCH_IMX21) || defined(CONFIG_ARCH_IMX27)

drivers/video/imx.c static int imxfb_probe(struct device_d *dev) · line 591

Quoted 10 lines
drivers/video/imx.c +10 -0
+	fbi->ahb_clk = clk_get(dev, "ahb");
+	if (IS_ERR(fbi->ahb_clk))
+		return PTR_ERR(fbi->ahb_clk);
+#endif
+
+#ifdef CONFIG_ARCH_IMX27
+	fbi->ipg_clk = clk_get(dev, "ipg");
+	if (IS_ERR(fbi->ipg_clk))
+		return PTR_ERR(fbi->ipg_clk);
+#endif

Please provide a dummy ipg clock for the i.MX21. Then you can remove all the ifdefs. Otherwise the series looks good.

Since you patch the i.MX21 clock file, have you tested this series on such a hardware? It would be interesting to know if it still works since I do not have a i.MX21 hardware.

Sascha

Signature · 9 lines
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
#4 lore raw

PATCH 3/4 i.MX27: fix shift amount for PCCR1_PERCLK3_EN

In reply to Daniel Mierswa
---
 arch/arm/mach-imx/clk-imx27.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/mach-imx/clk-imx27.c +1 -1
index 958495e..e221928 100644
@@ -179,7 +179,7 @@ static int imx27_ccm_probe(struct device_d *dev)
 	else
 		clks[cpu_div] = imx_clk_divider("cpu_div", "cpu_sel", base + CCM_CSCR, 13, 3);
 	clks[clko_div] = imx_clk_divider("clko_div", "clko_sel", base + CCM_PCDR0, 22, 3);
-	clks[lcdc_per_gate] = imx_clk_gate("lcdc_per_gate", "per3_div", base + CCM_PCCR1, 7);
+	clks[lcdc_per_gate] = imx_clk_gate("lcdc_per_gate", "per3_div", base + CCM_PCCR1, 8);
 	clks[lcdc_ahb_gate] = imx_clk_gate("lcdc_ahb_gate", "ahb", base + CCM_PCCR1, 15);
 	clks[lcdc_ipg_gate] = imx_clk_gate("lcdc_ipg_gate", "ipg", base + CCM_PCCR0, 14);
 
Signature · 7 lines
1.8.1


_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
#5 lore raw

PATCH 4/4 graphic_utils: always initialize offscreenbuf member

In reply to Daniel Mierswa

If offscreen was not passed to the function the resulting offscreenbuf was a dangling pointer and the free() call in fd_close would result in undefined behaviour.

---
 lib/gui/graphic_utils.c | 2 ++
 1 file changed, 2 insertions(+)
lib/gui/graphic_utils.c +2 -0
index 3800ee2..79200de 100644
@@ -226,6 +226,8 @@ int fb_open(const char * fbdev, struct screen *sc, bool offscreen)
 		 * on the framebuffer
 		 */
 		sc->offscreenbuf = malloc(sc->fbsize);
+	} else {
+		sc->offscreenbuf = NULL;
 	}
 
 	return sc->fd;
Signature · 7 lines
1.8.1


_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
#6 lore raw

Re: [PATCH 4/4] graphic_utils: always initialize offscreenbuf member

Quoted 14 lines · Daniel Mierswa

If offscreen was not passed to the function the resulting offscreenbuf was a dangling pointer and the free() call in fd_close would result in undefined behaviour.

---
 lib/gui/graphic_utils.c | 2 ++
 1 file changed, 2 insertions(+)
lib/gui/graphic_utils.c +0 -0
index 3800ee2..79200de 100644

lib/gui/graphic_utils.c int fb_open(const char * fbdev, struct screen *sc, bool offscreen) · line 231

Quoted 6 lines
lib/gui/graphic_utils.c +2 -0
@@ -226,6 +226,8 @@ int fb_open(const char * fbdev, struct screen *sc, bool offscreen)
 		 * on the framebuffer
 		 */
 		sc->offscreenbuf = malloc(sc->fbsize);
+	} else {
+		sc->offscreenbuf = NULL;
 	}

no you do not touch the struct if we do not ask you a offscreen

the one that call fb_open need to init the struct screen

Best Regards,
J.

_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox