Exynos SROMc configuration and Ethernet support for SMDK5410

index 33886d5..cce5c1f 100644
@@ -5,8 +5,75 @@ Required properties:
 
 - reg: offset and length of the register set
 
-Example:
+Optional properties:
+The SROM controller can be used to attach external peripherals. In this case
+extra properties, describing the bus behind it, should be specified as below:
+
+- #address-cells: Must be set to 2 to allow memory address translation
+
+- #size-cells: Must be set to 1 to allow CS address passing
+
+- ranges: Must be set up to reflect the memory layout with four integer values
+	  per bank:
+		<bank-number> 0 <physical address of bank> <size>
+
+Sub-nodes:
+The actual device nodes should be added as subnodes to the SROMc node. These
+subnodes, except regular device specification, should contain the following
+properties, describing configuration of the relevant SROM bank:
+
+Required properties:
+- reg: bank number, base address (relative to start of the bank) and size of
+       the memory mapped for the device. Note that base address will be
+       typically 0 as this is the start of the bank.
+
+- samsung,srom-timing : array of 6 integers, specifying bank timings in the
+                        following order: Tacp, Tcah, Tcoh, Tacc, Tcos, Tacs.
+                        Each value is specified in cycles and has the following
+                        meaning and valid range:
+                        Tacp : Page mode access cycle at Page mode (0 - 15)
+                        Tcah : Address holding time after CSn (0 - 15)
+                        Tcoh : Chip selection hold on OEn (0 - 15)
+                        Tacc : Access cycle (0 - 32)
+                        Tcos : Chip selection set-up before OEn (0 - 15)
+                        Tacs : Address set-up before CSn (0 - 15)
+
+Optional properties:
+- reg-io-width : data width in bytes (1 or 2). If omitted, default of 1 is used.
+
+- samsung,srom-page-mode : page mode configuration for the bank:
+			   0 - normal (one data)
+			   1 - four data
+			   If omitted, default of 0 is used.
+
+Example: basic definition, no banks are configured
+	sromc at 12570000 {
+		compatible = "samsung,exynos-srom";
+		reg = <0x12570000 0x14>;
+	};
+
+Example: SROMc with SMSC911x ethernet chip on bank 3
 	sromc at 12570000 {
+		#address-cells = <2>;
+		#size-cells = <1>;
+		ranges = <0 0 0x04000000 0x20000   // Bank0
+			  1 0 0x05000000 0x20000   // Bank1
+			  2 0 0x06000000 0x20000   // Bank2
+			  3 0 0x07000000 0x20000>; // Bank3
+
 		compatible = "samsung,exynos-srom";
-		reg = <0x12570000 0x10>;
+		reg = <0x12570000 0x14>;
+
+		ethernet at 3 {
+			compatible = "smsc,lan9115";
+			reg = <3 0 0x10000>;	   // Bank 3, offset = 0
+			phy-mode = "mii";
+			interrupt-parent = <&gpx0>;
+			interrupts = <5 8>;
+			reg-io-width = <2>;
+			smsc,irq-push-pull;
+			smsc,force-internal-phy;
+
+			samsung,srom-config = <1 9 12 1 9 1 1>;
+		};
 	};

index 4603356..e2b58f8 100644
@@ -101,6 +101,11 @@
 			reg = <0x10000000 0x100>;
 		};
 
+		sromc: sromc at 12250000 {
+			compatible = "samsung,exynos-srom";
+			reg = <0x12250000 0x14>;
+		};
+
 		pmu_system_controller: system-controller at 10040000 {
 			compatible = "samsung,exynos5410-pmu", "syscon";
 			reg = <0x10040000 0x5000>;

index 83c85f5..c22dc42 100644
@@ -16,7 +16,7 @@ menuconfig ARCH_EXYNOS
 	select ARM_GIC
 	select COMMON_CLK_SAMSUNG
 	select EXYNOS_THERMAL
-	select EXYNOS_SROM if PM
+	select EXYNOS_SROM
 	select HAVE_ARM_SCU if SMP
 	select HAVE_S3C2410_I2C if I2C
 	select HAVE_S3C2410_WATCHDOG if WATCHDOG

index 2833b5b..ea4bc2a 100644
@@ -8,6 +8,6 @@ config SOC_SAMSUNG
 
 config EXYNOS_SROM
 	bool
-	depends on ARM && ARCH_EXYNOS && PM
+	depends on ARM && ARCH_EXYNOS
 
 endmenu

index cebeaab..373abf7 100644
@@ -11,6 +11,7 @@
 
 /dts-v1/;
 #include "exynos5410.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
 / {
 	model = "Samsung SMDK5410 board based on EXYNOS5410";
 	compatible = "samsung,smdk5410", "samsung,exynos5410", "samsung,exynos5";

@@ -61,6 +62,46 @@
 	disable-wp;
 };
 
+&pinctrl_0 {
+	srom_ctl: srom-ctl {
+		samsung,pins = "gpy0-3", "gpy0-4", "gpy0-5",
+			       "gpy1-0", "gpy1-1", "gpy1-2", "gpy1-3";
+		samsung,pin-function = <2>;
+		samsung,pin-drv = <0>;
+	};
+
+	srom_ebi: srom-ebi {
+		samsung,pins = "gpy3-0", "gpy3-1", "gpy3-2", "gpy3-3",
+			       "gpy3-4", "gpy3-5", "gpy3-6", "gpy3-7",
+			       "gpy5-0", "gpy5-1", "gpy5-2", "gpy5-3",
+			       "gpy5-4", "gpy5-5", "gpy5-6", "gpy5-7",
+			       "gpy6-0", "gpy6-1", "gpy6-2", "gpy6-3",
+			       "gpy6-4", "gpy6-5", "gpy6-6", "gpy6-7";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <3>;
+		samsung,pin-drv = <0>;
+	};
+};
+
+&sromc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&srom_ctl>, <&srom_ebi>;
+
+	ethernet at 3 {
+		compatible = "smsc,lan9115";
+		reg = <3 0 0x10000>;
+		phy-mode = "mii";
+		interrupt-parent = <&gpx0>;
+		interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
+		reg-io-width = <2>;
+		smsc,irq-push-pull;
+		smsc,force-internal-phy;
+
+		samsung,srom-page-mode = <1>;
+		samsung,srom-timing = <9 12 1 9 1 1>;
+	};
+};
+
 &uart0 {
 	status = "okay";
 };

index e2b58f8..9cfb814 100644
@@ -104,6 +104,12 @@
 		sromc: sromc at 12250000 {
 			compatible = "samsung,exynos-srom";
 			reg = <0x12250000 0x14>;
+			#address-cells = <2>;
+			#size-cells = <1>;
+			ranges = <0 0 0x04000000 0x20000
+				  1 0 0x05000000 0x20000
+				  2 0 0x06000000 0x20000
+				  3 0 0x07000000 0x20000>;
 		};
 
 		pmu_system_controller: system-controller at 10040000 {