Skip to contentSkip to conversation

Add coresight support for SDM845, MSM8998 and MSM8996

PATCH Superseded Sai Prakash Ranjan 6 participants 20 messages Jan 28, 2019 – Jan 31, 2019

Subsystems (5)

v5 of 9 Superseded Latest is v9 →

lore
Share & tools
lore
#0 lore raw

v5 cover Add coresight support for SDM845, MSM8998 and MSM8996

This patch series adds support for coresight on SDM845, MSM8998, and MSM8996.

* Patch 1 adds device tree nodes for SDM845 coresight components.

* Patch 2 adds device tree nodes for MSM8998 coresight components.

* Patch 3 adds device tree nodes for MSM8996 coresight components.

* Patch 4 enables support for ETMv4.2 and enables SDM845 to make use of same driver(etm4x).

* Patch 5 adds ETM PIDs for SDM845 and MSM8996.

* Patch 6 adds UCI table for coresight CPU debug module and also adds a helper macro for making ID insertion simpler.

* Patch 7 is a trivial removal of duplicate header file.

Patch 1 and 4 depends on below AOSS QMP patches by Bjorn:
https://patchwork.kernel.org/patch/10749469/
https://patchwork.kernel.org/patch/10749481/
https://patchwork.kernel.org/patch/10749479/
https://patchwork.kernel.org/patch/10749475/

Patch 2 depends on MSM8998 rpm clocks and rpmcc nodes:
https://lore.kernel.org/lkml/[email protected]/
https://lore.kernel.org/lkml/[email protected]/

Patch 5 and 6 depends on UCI support by Mike Leach:
https://lore.kernel.org/lkml/[email protected]/

This patch series has been tested on SDM845 MTP and MSM8996 based Dragonboard 820c and MSM8998 MTP.

v5:
* Added coresight support for MSM8998.
* Added ETM PIDs for SDM845 and MSM8996 as suggested by Suzuki.
* Added UCI table for Coresight CPU debug module.

v4:
* Mask out the minor version as suggested by Mathieu.
* Added the dependent patch description in patch 1.

v3:
* Added arm,scatter-gather property as suggested by Suzuki.

v2:
* Added coresight support for msm8996 based on Vivek's patch. Cleaned up and added coresight cpu debug nodes for msm8996.
* Merged coresight dtsi file into sdm845.dtsi as suggested by Bjorn
* Addressed Mathieu's feedback about masking the minor version in etm4_arch_supported() and added a comment for reason to bypass the AMBA bus discovery method.

Sai Prakash Ranjan (6):
arm64: dts: qcom: sdm845: Add Coresight support
arm64: dts: qcom: msm8998: Add Coresight support
coresight: etm4x: Add support to enable ETMv4.2
coresight: etm4x: Add ETM PIDs for SDM845 and MSM8996
coresight: debug: Add Unique Component Identifier (UCI) table
arm64: dts: qcom: sdm845: Remove the duplicate header inclusion

Vivek Gautam (1):
arm64: dts: qcom: msm8996: Add Coresight support

 arch/arm64/boot/dts/qcom/msm8996.dtsi         | 434 +++++++++++++++++
 arch/arm64/boot/dts/qcom/msm8998.dtsi         | 435 ++++++++++++++++++
 arch/arm64/boot/dts/qcom/sdm845.dtsi          | 435 +++++++++++++++++-
 .../hwtracing/coresight/coresight-cpu-debug.c |  41 +-
 drivers/hwtracing/coresight/coresight-etm4x.c |   7 +-
 5 files changed, 1337 insertions(+), 15 deletions(-)
Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
#1 lore raw

PATCH v5 1/7 arm64: dts: qcom: sdm845: Add Coresight support

Add coresight components found on Qualcomm SDM845 SoC.

---
Depends on AOSS QMP side channel patches and AMBA bus pclk change by Bjorn Andersson [1][2].
Also depends on patch ("arm64: dts: qcom: sdm845: Increase address and size cells for soc") [3].

[1] https://lore.kernel.org/lkml/[email protected]/
[2] https://lore.kernel.org/lkml/[email protected]/
[3] https://lore.kernel.org/lkml/[email protected]/

---
 arch/arm64/boot/dts/qcom/sdm845.dtsi | 434 +++++++++++++++++++++++++++
 1 file changed, 434 insertions(+)
arch/arm64/boot/dts/qcom/sdm845.dtsi +434 -0
index c27cbd3bcb0a..e49f71d00854 100644
@@ -1348,6 +1348,440 @@
 			};
 		};
 
+		stm@6002000 {
+			compatible = "arm,coresight-stm", "arm,primecell";
+			reg = <0 0x06002000 0 0x1000>,
+			      <0 0x16280000 0 0x180000>;
+			reg-names = "stm-base", "stm-stimulus-base";
+
+			power-domains = <&aoss_qmp AOSS_QMP_QDSS_CLK>;
+
+			out-ports {
+				port {
+					stm_out: endpoint {
+						remote-endpoint =
+						  <&funnel0_in7>;
+					};
+				};
+			};
+		};
+
+		funnel@6041000 {
+			compatible = "arm,coresight-funnel", "arm,primecell";
+			reg = <0 0x06041000 0 0x1000>;
+
+			power-domains = <&aoss_qmp AOSS_QMP_QDSS_CLK>;
+
+			out-ports {
+				port {
+					funnel0_out: endpoint {
+						remote-endpoint =
+						  <&merge_funnel_in0>;
+					};
+				};
+			};
+
+			in-ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@7 {
+					reg = <7>;
+					funnel0_in7: endpoint {
+						remote-endpoint = <&stm_out>;
+					};
+				};
+			};
+		};
+
+		funnel@6043000 {
+			compatible = "arm,coresight-funnel", "arm,primecell";
+			reg = <0 0x06043000 0 0x1000>;
+
+			power-domains = <&aoss_qmp AOSS_QMP_QDSS_CLK>;
+
+			out-ports {
+				port {
+					funnel2_out: endpoint {
+						remote-endpoint =
+						  <&merge_funnel_in2>;
+					};
+				};
+			};
+
+			in-ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@5 {
+					reg = <5>;
+					funnel2_in5: endpoint {
+						remote-endpoint =
+						  <&apss_merge_funnel_out>;
+					};
+				};
+			};
+		};
+
+		funnel@6045000 {
+			compatible = "arm,coresight-funnel", "arm,primecell";
+			reg = <0 0x06045000 0 0x1000>;
+
+			power-domains = <&aoss_qmp AOSS_QMP_QDSS_CLK>;
+
+			out-ports {
+				port {
+					merge_funnel_out: endpoint {
+						remote-endpoint = <&etf_in>;
+					};
+				};
+			};
+
+			in-ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					merge_funnel_in0: endpoint {
+						remote-endpoint =
+						  <&funnel0_out>;
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+					merge_funnel_in2: endpoint {
+						remote-endpoint =
+						  <&funnel2_out>;
+					};
+				};
+			};
+		};
+
+		replicator@6046000 {
+			compatible = "arm,coresight-dynamic-replicator", "arm,primecell";
+			reg = <0 0x06046000 0 0x1000>;
+
+			power-domains = <&aoss_qmp AOSS_QMP_QDSS_CLK>;
+
+			out-ports {
+				port {
+					replicator_out: endpoint {
+						remote-endpoint = <&etr_in>;
+					};
+				};
+			};
+
+			in-ports {
+				port {
+					replicator_in: endpoint {
+						remote-endpoint = <&etf_out>;
+					};
+				};
+			};
+		};
+
+		etf@6047000 {
+			compatible = "arm,coresight-tmc", "arm,primecell";
+			reg = <0 0x06047000 0 0x1000>;
+
+			power-domains = <&aoss_qmp AOSS_QMP_QDSS_CLK>;
+
+			out-ports {
+				port {
+					etf_out: endpoint {
+						remote-endpoint =
+						  <&replicator_in>;
+					};
+				};
+			};
+
+			in-ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@1 {
+					reg = <1>;
+					etf_in: endpoint {
+						remote-endpoint =
+						  <&merge_funnel_out>;
+					};
+				};
+			};
+		};
+
+		etr@6048000 {
+			compatible = "arm,coresight-tmc", "arm,primecell";
+			reg = <0 0x06048000 0 0x1000>;
+
+			power-domains = <&aoss_qmp AOSS_QMP_QDSS_CLK>;
+			arm,scatter-gather;
+
+			in-ports {
+				port {
+					etr_in: endpoint {
+						remote-endpoint =
+						  <&replicator_out>;
+					};
+				};
+			};
+		};
+
+		etm@7040000 {
+			compatible = "arm,coresight-etm4x", "arm,primecell";
+			reg = <0 0x07040000 0 0x1000>;
+
+			cpu = <&CPU0>;
+
+			power-domains = <&aoss_qmp AOSS_QMP_QDSS_CLK>;
+
+			out-ports {
+				port {
+					etm0_out: endpoint {
+						remote-endpoint =
+						  <&apss_funnel_in0>;
+					};
+				};
+			};
+		};
+
+		etm@7140000 {
+			compatible = "arm,coresight-etm4x", "arm,primecell";
+			reg = <0 0x07140000 0 0x1000>;
+
+			cpu = <&CPU1>;
+
+			power-domains = <&aoss_qmp AOSS_QMP_QDSS_CLK>;
+
+			out-ports {
+				port {
+					etm1_out: endpoint {
+						remote-endpoint =
+						  <&apss_funnel_in1>;
+					};
+				};
+			};
+		};
+
+		etm@7240000 {
+			compatible = "arm,coresight-etm4x", "arm,primecell";
+			reg = <0 0x07240000 0 0x1000>;
+
+			cpu = <&CPU2>;
+
+			power-domains = <&aoss_qmp AOSS_QMP_QDSS_CLK>;
+
+			out-ports {
+				port {
+					etm2_out: endpoint {
+						remote-endpoint =
+						  <&apss_funnel_in2>;
+					};
+				};
+			};
+		};
+
+		etm@7340000 {
+			compatible = "arm,coresight-etm4x", "arm,primecell";
+			reg = <0 0x07340000 0 0x1000>;
+
+			cpu = <&CPU3>;
+
+			power-domains = <&aoss_qmp AOSS_QMP_QDSS_CLK>;
+
+			out-ports {
+				port {
+					etm3_out: endpoint {
+						remote-endpoint =
+						  <&apss_funnel_in3>;
+					};
+				};
+			};
+		};
+
+		etm@7440000 {
+			compatible = "arm,coresight-etm4x", "arm,primecell";
+			reg = <0 0x07440000 0 0x1000>;
+
+			cpu = <&CPU4>;
+
+			power-domains = <&aoss_qmp AOSS_QMP_QDSS_CLK>;
+
+			out-ports {
+				port {
+					etm4_out: endpoint {
+						remote-endpoint =
+						  <&apss_funnel_in4>;
+					};
+				};
+			};
+		};
+
+		etm@7540000 {
+			compatible = "arm,coresight-etm4x", "arm,primecell";
+			reg = <0 0x07540000 0 0x1000>;
+
+			cpu = <&CPU5>;
+
+			power-domains = <&aoss_qmp AOSS_QMP_QDSS_CLK>;
+
+			out-ports {
+				port {
+					etm5_out: endpoint {
+						remote-endpoint =
+						  <&apss_funnel_in5>;
+					};
+				};
+			};
+		};
+
+		etm@7640000 {
+			compatible = "arm,coresight-etm4x", "arm,primecell";
+			reg = <0 0x07640000 0 0x1000>;
+
+			cpu = <&CPU6>;
+
+			power-domains = <&aoss_qmp AOSS_QMP_QDSS_CLK>;
+
+			out-ports {
+				port {
+					etm6_out: endpoint {
+						remote-endpoint =
+						  <&apss_funnel_in6>;
+					};
+				};
+			};
+		};
+
+		etm@7740000 {
+			compatible = "arm,coresight-etm4x", "arm,primecell";
+			reg = <0 0x07740000 0 0x1000>;
+
+			cpu = <&CPU7>;
+
+			power-domains = <&aoss_qmp AOSS_QMP_QDSS_CLK>;
+
+			out-ports {
+				port {
+					etm7_out: endpoint {
+						remote-endpoint =
+						  <&apss_funnel_in7>;
+					};
+				};
+			};
+		};
+
+		funnel@7800000 { /* APSS Funnel */
+			compatible = "arm,coresight-funnel", "arm,primecell";
+			reg = <0 0x07800000 0 0x1000>;
+
+			power-domains = <&aoss_qmp AOSS_QMP_QDSS_CLK>;
+
+			out-ports {
+				port {
+					apss_funnel_out: endpoint {
+						remote-endpoint =
+						  <&apss_merge_funnel_in>;
+					};
+				};
+			};
+
+			in-ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					apss_funnel_in0: endpoint {
+						remote-endpoint =
+						  <&etm0_out>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					apss_funnel_in1: endpoint {
+						remote-endpoint =
+						  <&etm1_out>;
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+					apss_funnel_in2: endpoint {
+						remote-endpoint =
+						  <&etm2_out>;
+					};
+				};
+
+				port@3 {
+					reg = <3>;
+					apss_funnel_in3: endpoint {
+						remote-endpoint =
+						  <&etm3_out>;
+					};
+				};
+
+				port@4 {
+					reg = <4>;
+					apss_funnel_in4: endpoint {
+						remote-endpoint =
+						  <&etm4_out>;
+					};
+				};
+
+				port@5 {
+					reg = <5>;
+					apss_funnel_in5: endpoint {
+						remote-endpoint =
+						  <&etm5_out>;
+					};
+				};
+
+				port@6 {
+					reg = <6>;
+					apss_funnel_in6: endpoint {
+						remote-endpoint =
+						  <&etm6_out>;
+					};
+				};
+
+				port@7 {
+					reg = <7>;
+					apss_funnel_in7: endpoint {
+						remote-endpoint =
+						  <&etm7_out>;
+					};
+				};
+			};
+		};
+
+		funnel@7810000 {
+			compatible = "arm,coresight-funnel", "arm,primecell";
+			reg = <0 0x07810000 0 0x1000>;
+
+			power-domains = <&aoss_qmp AOSS_QMP_QDSS_CLK>;
+
+			out-ports {
+				port {
+					apss_merge_funnel_out: endpoint {
+						remote-endpoint =
+						  <&funnel2_in5>;
+					};
+				};
+			};
+
+			in-ports {
+				port {
+					apss_merge_funnel_in: endpoint {
+						remote-endpoint =
+						  <&apss_funnel_out>;
+					};
+				};
+			};
+		};
+
 		usb_1_hsphy: phy@88e2000 {
 			compatible = "qcom,sdm845-qusb2-phy";
 			reg = <0x88e2000 0x400>;
Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
#2 lore raw

Re: [PATCHv5 1/7] arm64: dts: qcom: sdm845: Add Coresight support

Quoted 10 lines · Sai Prakash Ranjan

Add coresight components found on Qualcomm SDM845 SoC.

---
Depends on AOSS QMP side channel patches and AMBA bus pclk change by Bjorn Andersson [1][2].
Also depends on patch ("arm64: dts: qcom: sdm845: Increase address and size cells for soc") [3].

Quoted 3 lines

[1] https://lore.kernel.org/lkml/[email protected]/
[2] https://lore.kernel.org/lkml/[email protected]/
[3] https://lore.kernel.org/lkml/[email protected]/

This patch still doesn't compile for me. In the above [1] is a cover letter and
[2] is a patch that is part of [1] - what do you want me to do? Add all the patches in [1]? And how do those related to the dependencies you've listed in the cover letter?

I can't continue reviewing your work until you provide me with a tree based on coresight-next [3] with all the depencendies to get this set applied and compiled.

Mathieu

[3]. https://git.linaro.org/kernel/coresight.git/log/?h=next

Quoted 453 lines
---
 arch/arm64/boot/dts/qcom/sdm845.dtsi | 434 +++++++++++++++++++++++++++
 1 file changed, 434 insertions(+)
arch/arm64/boot/dts/qcom/sdm845.dtsi +434 -0
index c27cbd3bcb0a..e49f71d00854 100644
@@ -1348,6 +1348,440 @@
 			};
 		};
 
+		stm@6002000 {
+			compatible = "arm,coresight-stm", "arm,primecell";
+			reg = <0 0x06002000 0 0x1000>,
+			      <0 0x16280000 0 0x180000>;
+			reg-names = "stm-base", "stm-stimulus-base";
+
+			power-domains = <&aoss_qmp AOSS_QMP_QDSS_CLK>;
+
+			out-ports {
+				port {
+					stm_out: endpoint {
+						remote-endpoint =
+						  <&funnel0_in7>;
+					};
+				};
+			};
+		};
+
+		funnel@6041000 {
+			compatible = "arm,coresight-funnel", "arm,primecell";
+			reg = <0 0x06041000 0 0x1000>;
+
+			power-domains = <&aoss_qmp AOSS_QMP_QDSS_CLK>;
+
+			out-ports {
+				port {
+					funnel0_out: endpoint {
+						remote-endpoint =
+						  <&merge_funnel_in0>;
+					};
+				};
+			};
+
+			in-ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@7 {
+					reg = <7>;
+					funnel0_in7: endpoint {
+						remote-endpoint = <&stm_out>;
+					};
+				};
+			};
+		};
+
+		funnel@6043000 {
+			compatible = "arm,coresight-funnel", "arm,primecell";
+			reg = <0 0x06043000 0 0x1000>;
+
+			power-domains = <&aoss_qmp AOSS_QMP_QDSS_CLK>;
+
+			out-ports {
+				port {
+					funnel2_out: endpoint {
+						remote-endpoint =
+						  <&merge_funnel_in2>;
+					};
+				};
+			};
+
+			in-ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@5 {
+					reg = <5>;
+					funnel2_in5: endpoint {
+						remote-endpoint =
+						  <&apss_merge_funnel_out>;
+					};
+				};
+			};
+		};
+
+		funnel@6045000 {
+			compatible = "arm,coresight-funnel", "arm,primecell";
+			reg = <0 0x06045000 0 0x1000>;
+
+			power-domains = <&aoss_qmp AOSS_QMP_QDSS_CLK>;
+
+			out-ports {
+				port {
+					merge_funnel_out: endpoint {
+						remote-endpoint = <&etf_in>;
+					};
+				};
+			};
+
+			in-ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					merge_funnel_in0: endpoint {
+						remote-endpoint =
+						  <&funnel0_out>;
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+					merge_funnel_in2: endpoint {
+						remote-endpoint =
+						  <&funnel2_out>;
+					};
+				};
+			};
+		};
+
+		replicator@6046000 {
+			compatible = "arm,coresight-dynamic-replicator", "arm,primecell";
+			reg = <0 0x06046000 0 0x1000>;
+
+			power-domains = <&aoss_qmp AOSS_QMP_QDSS_CLK>;
+
+			out-ports {
+				port {
+					replicator_out: endpoint {
+						remote-endpoint = <&etr_in>;
+					};
+				};
+			};
+
+			in-ports {
+				port {
+					replicator_in: endpoint {
+						remote-endpoint = <&etf_out>;
+					};
+				};
+			};
+		};
+
+		etf@6047000 {
+			compatible = "arm,coresight-tmc", "arm,primecell";
+			reg = <0 0x06047000 0 0x1000>;
+
+			power-domains = <&aoss_qmp AOSS_QMP_QDSS_CLK>;
+
+			out-ports {
+				port {
+					etf_out: endpoint {
+						remote-endpoint =
+						  <&replicator_in>;
+					};
+				};
+			};
+
+			in-ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@1 {
+					reg = <1>;
+					etf_in: endpoint {
+						remote-endpoint =
+						  <&merge_funnel_out>;
+					};
+				};
+			};
+		};
+
+		etr@6048000 {
+			compatible = "arm,coresight-tmc", "arm,primecell";
+			reg = <0 0x06048000 0 0x1000>;
+
+			power-domains = <&aoss_qmp AOSS_QMP_QDSS_CLK>;
+			arm,scatter-gather;
+
+			in-ports {
+				port {
+					etr_in: endpoint {
+						remote-endpoint =
+						  <&replicator_out>;
+					};
+				};
+			};
+		};
+
+		etm@7040000 {
+			compatible = "arm,coresight-etm4x", "arm,primecell";
+			reg = <0 0x07040000 0 0x1000>;
+
+			cpu = <&CPU0>;
+
+			power-domains = <&aoss_qmp AOSS_QMP_QDSS_CLK>;
+
+			out-ports {
+				port {
+					etm0_out: endpoint {
+						remote-endpoint =
+						  <&apss_funnel_in0>;
+					};
+				};
+			};
+		};
+
+		etm@7140000 {
+			compatible = "arm,coresight-etm4x", "arm,primecell";
+			reg = <0 0x07140000 0 0x1000>;
+
+			cpu = <&CPU1>;
+
+			power-domains = <&aoss_qmp AOSS_QMP_QDSS_CLK>;
+
+			out-ports {
+				port {
+					etm1_out: endpoint {
+						remote-endpoint =
+						  <&apss_funnel_in1>;
+					};
+				};
+			};
+		};
+
+		etm@7240000 {
+			compatible = "arm,coresight-etm4x", "arm,primecell";
+			reg = <0 0x07240000 0 0x1000>;
+
+			cpu = <&CPU2>;
+
+			power-domains = <&aoss_qmp AOSS_QMP_QDSS_CLK>;
+
+			out-ports {
+				port {
+					etm2_out: endpoint {
+						remote-endpoint =
+						  <&apss_funnel_in2>;
+					};
+				};
+			};
+		};
+
+		etm@7340000 {
+			compatible = "arm,coresight-etm4x", "arm,primecell";
+			reg = <0 0x07340000 0 0x1000>;
+
+			cpu = <&CPU3>;
+
+			power-domains = <&aoss_qmp AOSS_QMP_QDSS_CLK>;
+
+			out-ports {
+				port {
+					etm3_out: endpoint {
+						remote-endpoint =
+						  <&apss_funnel_in3>;
+					};
+				};
+			};
+		};
+
+		etm@7440000 {
+			compatible = "arm,coresight-etm4x", "arm,primecell";
+			reg = <0 0x07440000 0 0x1000>;
+
+			cpu = <&CPU4>;
+
+			power-domains = <&aoss_qmp AOSS_QMP_QDSS_CLK>;
+
+			out-ports {
+				port {
+					etm4_out: endpoint {
+						remote-endpoint =
+						  <&apss_funnel_in4>;
+					};
+				};
+			};
+		};
+
+		etm@7540000 {
+			compatible = "arm,coresight-etm4x", "arm,primecell";
+			reg = <0 0x07540000 0 0x1000>;
+
+			cpu = <&CPU5>;
+
+			power-domains = <&aoss_qmp AOSS_QMP_QDSS_CLK>;
+
+			out-ports {
+				port {
+					etm5_out: endpoint {
+						remote-endpoint =
+						  <&apss_funnel_in5>;
+					};
+				};
+			};
+		};
+
+		etm@7640000 {
+			compatible = "arm,coresight-etm4x", "arm,primecell";
+			reg = <0 0x07640000 0 0x1000>;
+
+			cpu = <&CPU6>;
+
+			power-domains = <&aoss_qmp AOSS_QMP_QDSS_CLK>;
+
+			out-ports {
+				port {
+					etm6_out: endpoint {
+						remote-endpoint =
+						  <&apss_funnel_in6>;
+					};
+				};
+			};
+		};
+
+		etm@7740000 {
+			compatible = "arm,coresight-etm4x", "arm,primecell";
+			reg = <0 0x07740000 0 0x1000>;
+
+			cpu = <&CPU7>;
+
+			power-domains = <&aoss_qmp AOSS_QMP_QDSS_CLK>;
+
+			out-ports {
+				port {
+					etm7_out: endpoint {
+						remote-endpoint =
+						  <&apss_funnel_in7>;
+					};
+				};
+			};
+		};
+
+		funnel@7800000 { /* APSS Funnel */
+			compatible = "arm,coresight-funnel", "arm,primecell";
+			reg = <0 0x07800000 0 0x1000>;
+
+			power-domains = <&aoss_qmp AOSS_QMP_QDSS_CLK>;
+
+			out-ports {
+				port {
+					apss_funnel_out: endpoint {
+						remote-endpoint =
+						  <&apss_merge_funnel_in>;
+					};
+				};
+			};
+
+			in-ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					apss_funnel_in0: endpoint {
+						remote-endpoint =
+						  <&etm0_out>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					apss_funnel_in1: endpoint {
+						remote-endpoint =
+						  <&etm1_out>;
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+					apss_funnel_in2: endpoint {
+						remote-endpoint =
+						  <&etm2_out>;
+					};
+				};
+
+				port@3 {
+					reg = <3>;
+					apss_funnel_in3: endpoint {
+						remote-endpoint =
+						  <&etm3_out>;
+					};
+				};
+
+				port@4 {
+					reg = <4>;
+					apss_funnel_in4: endpoint {
+						remote-endpoint =
+						  <&etm4_out>;
+					};
+				};
+
+				port@5 {
+					reg = <5>;
+					apss_funnel_in5: endpoint {
+						remote-endpoint =
+						  <&etm5_out>;
+					};
+				};
+
+				port@6 {
+					reg = <6>;
+					apss_funnel_in6: endpoint {
+						remote-endpoint =
+						  <&etm6_out>;
+					};
+				};
+
+				port@7 {
+					reg = <7>;
+					apss_funnel_in7: endpoint {
+						remote-endpoint =
+						  <&etm7_out>;
+					};
+				};
+			};
+		};
+
+		funnel@7810000 {
+			compatible = "arm,coresight-funnel", "arm,primecell";
+			reg = <0 0x07810000 0 0x1000>;
+
+			power-domains = <&aoss_qmp AOSS_QMP_QDSS_CLK>;
+
+			out-ports {
+				port {
+					apss_merge_funnel_out: endpoint {
+						remote-endpoint =
+						  <&funnel2_in5>;
+					};
+				};
+			};
+
+			in-ports {
+				port {
+					apss_merge_funnel_in: endpoint {
+						remote-endpoint =
+						  <&apss_funnel_out>;
+					};
+				};
+			};
+		};
+
 		usb_1_hsphy: phy@88e2000 {
 			compatible = "qcom,sdm845-qusb2-phy";
 			reg = <0x88e2000 0x400>;
Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
#3 lore raw

Re: [PATCHv5 1/7] arm64: dts: qcom: sdm845: Add Coresight support

Quoted 15 lines · Mathieu Poirier
Quoted 10 lines · Sai Prakash Ranjan

Add coresight components found on Qualcomm SDM845 SoC.

---
Depends on AOSS QMP side channel patches and AMBA bus pclk change by Bjorn Andersson [1][2].
Also depends on patch ("arm64: dts: qcom: sdm845: Increase address and size cells for soc") [3].

Quoted 3 lines

[1] https://lore.kernel.org/lkml/[email protected]/
[2] https://lore.kernel.org/lkml/[email protected]/
[3] https://lore.kernel.org/lkml/[email protected]/

Quoted 9 lines

This patch still doesn't compile for me. In the above [1] is a cover letter and
[2] is a patch that is part of [1] - what do you want me to do? Add all the patches in [1]? And how do those related to the dependencies you've listed in the cover letter?

I can't continue reviewing your work until you provide me with a tree based on coresight-next [3] with all the depencendies to get this set applied and compiled.

Hi Mathieu,

Sorry to have wasted your time. There were many dependencies
with some nesting and getting updated as well, so in the next version, I will have my patches rebased on top of coresight-next and also I will give a tree based on the same with all dependencies applied.

Thanks,
Sai

Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
#4 lore raw

PATCH v5 2/7 arm64: dts: qcom: msm8998: Add Coresight support

In reply to Sai Prakash Ranjan

Enable coresight support by adding device nodes for the available source, sinks and channel blocks on MSM8998.

---
This depends on MSM8998 rpm clocks and rpmcc node by Jeffrey Hugo
and Marc Gonzalez [1][2].
[1] https://lore.kernel.org/lkml/[email protected]/
[2] https://lore.kernel.org/lkml/[email protected]/

---
 arch/arm64/boot/dts/qcom/msm8998.dtsi | 435 ++++++++++++++++++++++++++
 1 file changed, 435 insertions(+)
arch/arm64/boot/dts/qcom/msm8998.dtsi +435 -0
index 8d41b69ec2da..22ca14ee05b6 100644
@@ -560,6 +560,441 @@
 			#interrupt-cells = <0x2>;
 		};
 
+		stm@6002000 {
+			compatible = "arm,coresight-stm", "arm,primecell";
+			reg = <0x06002000 0x1000>,
+			      <0x16280000 0x180000>;
+			reg-names = "stm-base", "stm-data-base";
+
+			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			out-ports {
+				port {
+					stm_out: endpoint {
+						remote-endpoint = <&funnel0_in7>;
+					};
+				};
+			};
+		};
+
+		funnel@6041000 {
+			compatible = "arm,coresight-funnel", "arm,primecell";
+			reg = <0x06041000 0x1000>;
+
+			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			out-ports {
+				port {
+					funnel0_out: endpoint {
+						remote-endpoint =
+						  <&merge_funnel_in0>;
+					};
+				};
+			};
+
+			in-ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@7 {
+					reg = <7>;
+					funnel0_in7: endpoint {
+						remote-endpoint = <&stm_out>;
+					};
+				};
+			};
+		};
+
+		funnel@6042000 {
+			compatible = "arm,coresight-funnel", "arm,primecell";
+			reg = <0x06042000 0x1000>;
+
+			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			out-ports {
+				port {
+					funnel1_out: endpoint {
+						remote-endpoint =
+						  <&merge_funnel_in1>;
+					};
+				};
+			};
+
+			in-ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@6 {
+					reg = <6>;
+					funnel1_in6: endpoint {
+						remote-endpoint =
+						  <&apss_merge_funnel_out>;
+					};
+				};
+			};
+		};
+
+		funnel@6045000 {
+			compatible = "arm,coresight-funnel", "arm,primecell";
+			reg = <0x06045000 0x1000>;
+
+			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			out-ports {
+				port {
+					merge_funnel_out: endpoint {
+						remote-endpoint =
+						  <&etf_in>;
+					};
+				};
+			};
+
+			in-ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					merge_funnel_in0: endpoint {
+						remote-endpoint =
+						  <&funnel0_out>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					merge_funnel_in1: endpoint {
+						remote-endpoint =
+						  <&funnel1_out>;
+					};
+				};
+			};
+		};
+
+		replicator@6046000 {
+			compatible = "arm,coresight-dynamic-replicator", "arm,primecell";
+			reg = <0x06046000 0x1000>;
+
+			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			out-ports {
+				port {
+					replicator_out: endpoint {
+						remote-endpoint = <&etr_in>;
+					};
+				};
+			};
+
+			in-ports {
+				port {
+					replicator_in: endpoint {
+						remote-endpoint = <&etf_out>;
+					};
+				};
+			};
+		};
+
+		etf@6047000 {
+			compatible = "arm,coresight-tmc", "arm,primecell";
+			reg = <0x06047000 0x1000>;
+
+			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			out-ports {
+				port {
+					etf_out: endpoint {
+						remote-endpoint =
+						  <&replicator_in>;
+					};
+				};
+			};
+
+			in-ports {
+				port {
+					etf_in: endpoint {
+						remote-endpoint =
+						  <&merge_funnel_out>;
+					};
+				};
+			};
+		};
+
+		etr@6048000 {
+			compatible = "arm,coresight-tmc", "arm,primecell";
+			reg = <0x06048000 0x1000>;
+
+			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+			arm,scatter-gather;
+
+			in-ports {
+				port {
+					etr_in: endpoint {
+						remote-endpoint =
+						  <&replicator_out>;
+					};
+				};
+			};
+		};
+
+		etm@7840000 {
+			compatible = "arm,coresight-etm4x", "arm,primecell";
+			reg = <0x07840000 0x1000>;
+
+			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			cpu = <&CPU0>;
+
+			out-ports {
+				port {
+					etm0_out: endpoint {
+						remote-endpoint =
+						  <&apss_funnel_in0>;
+					};
+				};
+			};
+		};
+
+		etm@7940000 {
+			compatible = "arm,coresight-etm4x", "arm,primecell";
+			reg = <0x07940000 0x1000>;
+
+			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			cpu = <&CPU1>;
+
+			out-ports {
+				port {
+					etm1_out: endpoint {
+						remote-endpoint =
+						  <&apss_funnel_in1>;
+					};
+				};
+			};
+		};
+
+		etm@7a40000 {
+			compatible = "arm,coresight-etm4x", "arm,primecell";
+			reg = <0x07a40000 0x1000>;
+
+			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			cpu = <&CPU2>;
+
+			out-ports {
+				port {
+					etm2_out: endpoint {
+						remote-endpoint =
+						  <&apss_funnel_in2>;
+					};
+				};
+			};
+		};
+
+		etm@7b40000 {
+			compatible = "arm,coresight-etm4x", "arm,primecell";
+			reg = <0x07b40000 0x1000>;
+
+			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			cpu = <&CPU3>;
+
+			out-ports {
+				port {
+					etm3_out: endpoint {
+						remote-endpoint =
+						  <&apss_funnel_in3>;
+					};
+				};
+			};
+		};
+
+		funnel@7b60000 { /* APSS Funnel */
+			compatible = "arm,coresight-etm4x", "arm,primecell";
+			reg = <0x07b60000 0x1000>;
+
+			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			out-ports {
+				port {
+					apss_funnel_out: endpoint {
+						remote-endpoint =
+						  <&apss_merge_funnel_in>;
+					};
+				};
+			};
+
+			in-ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					apss_funnel_in0: endpoint {
+						remote-endpoint =
+						  <&etm0_out>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					apss_funnel_in1: endpoint {
+						remote-endpoint =
+						  <&etm1_out>;
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+					apss_funnel_in2: endpoint {
+						remote-endpoint =
+						  <&etm2_out>;
+					};
+				};
+
+				port@3 {
+					reg = <3>;
+					apss_funnel_in3: endpoint {
+						remote-endpoint =
+						  <&etm3_out>;
+					};
+				};
+
+				port@4 {
+					reg = <4>;
+					apss_funnel_in4: endpoint {
+						remote-endpoint =
+						  <&etm4_out>;
+					};
+				};
+
+				port@5 {
+					reg = <5>;
+					apss_funnel_in5: endpoint {
+						remote-endpoint =
+						  <&etm5_out>;
+					};
+				};
+
+				port@6 {
+					reg = <6>;
+					apss_funnel_in6: endpoint {
+						remote-endpoint =
+						  <&etm6_out>;
+					};
+				};
+
+				port@7 {
+					reg = <7>;
+					apss_funnel_in7: endpoint {
+						remote-endpoint =
+						  <&etm7_out>;
+					};
+				};
+			};
+		};
+
+		funnel@7b70000 {
+			compatible = "arm,coresight-funnel", "arm,primecell";
+			reg = <0x07b70000 0x1000>;
+
+			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			out-ports {
+				port {
+					apss_merge_funnel_out: endpoint {
+						remote-endpoint =
+						  <&funnel1_in6>;
+					};
+				};
+			};
+
+			in-ports {
+				port {
+					apss_merge_funnel_in: endpoint {
+						remote-endpoint =
+						  <&apss_funnel_out>;
+					};
+				};
+			};
+		};
+
+		etm@7c40000 {
+			compatible = "arm,coresight-etm4x", "arm,primecell";
+			reg = <0x07c40000 0x1000>;
+
+			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			cpu = <&CPU4>;
+
+			port{
+				etm4_out: endpoint {
+					remote-endpoint = <&apss_funnel_in4>;
+				};
+			};
+		};
+
+		etm@7d40000 {
+			compatible = "arm,coresight-etm4x", "arm,primecell";
+			reg = <0x07d40000 0x1000>;
+
+			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			cpu = <&CPU5>;
+
+			port{
+				etm5_out: endpoint {
+					remote-endpoint = <&apss_funnel_in5>;
+				};
+			};
+		};
+
+		etm@7e40000 {
+			compatible = "arm,coresight-etm4x", "arm,primecell";
+			reg = <0x07e40000 0x1000>;
+
+			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			cpu = <&CPU6>;
+
+			port{
+				etm6_out: endpoint {
+					remote-endpoint = <&apss_funnel_in6>;
+				};
+			};
+		};
+
+		etm@7f40000 {
+			compatible = "arm,coresight-etm4x", "arm,primecell";
+			reg = <0x07f40000 0x1000>;
+
+			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			cpu = <&CPU7>;
+
+			port{
+				etm7_out: endpoint {
+					remote-endpoint = <&apss_funnel_in7>;
+				};
+			};
+		};
+
 		spmi_bus: spmi@800f000 {
 			compatible = "qcom,spmi-pmic-arb";
 			reg =	<0x800f000 0x1000>,
Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
#5 lore raw

PATCH v5 3/7 arm64: dts: qcom: msm8996: Add Coresight support

In reply to Sai Prakash Ranjan

From: Vivek Gautam <[email protected]>

Enable coresight support by adding device nodes for the available source, sinks and channel blocks on msm8996.

This also adds coresight cpu debug nodes.

---
 arch/arm64/boot/dts/qcom/msm8996.dtsi | 434 ++++++++++++++++++++++++++
 1 file changed, 434 insertions(+)
arch/arm64/boot/dts/qcom/msm8996.dtsi +434 -0
index 99b7495455a6..3406a10f40db 100644
@@ -429,6 +429,440 @@
 			reg = <0x300000 0x90000>;
 		};
 
+		stm@3002000 {
+			compatible = "arm,coresight-stm", "arm,primecell";
+			reg = <0x3002000 0x1000>,
+			      <0x8280000 0x180000>;
+			reg-names = "stm-base", "stm-stimulus-base";
+
+			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			out-ports {
+				port {
+					stm_out: endpoint {
+						remote-endpoint =
+						  <&funnel0_in>;
+					};
+				};
+			};
+		};
+
+		tpiu@3020000 {
+			compatible = "arm,coresight-tpiu", "arm,primecell";
+			reg = <0x3020000 0x1000>;
+
+			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			in-ports {
+				port {
+					tpiu_in: endpoint {
+						remote-endpoint =
+						  <&replicator_out1>;
+					};
+				};
+			};
+		};
+
+		funnel@3021000 {
+			compatible = "arm,coresight-funnel", "arm,primecell";
+			reg = <0x3021000 0x1000>;
+
+			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			in-ports {
+				port {
+					funnel0_in: endpoint {
+						remote-endpoint =
+						  <&stm_out>;
+					};
+				};
+			};
+
+			out-ports {
+				port {
+					funnel0_out: endpoint {
+						remote-endpoint =
+						  <&merge_funnel_in0>;
+					};
+				};
+			};
+		};
+
+		funnel@3022000 {
+			compatible = "arm,coresight-funnel", "arm,primecell";
+			reg = <0x3022000 0x1000>;
+
+			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			in-ports {
+				port {
+					funnel1_in: endpoint {
+						remote-endpoint =
+						  <&apss_merge_funnel_out>;
+					};
+				};
+			};
+
+			out-ports {
+				port {
+					funnel1_out: endpoint {
+						remote-endpoint =
+						  <&merge_funnel_in1>;
+					};
+				};
+			};
+		};
+
+		funnel@3025000 {
+			compatible = "arm,coresight-funnel", "arm,primecell";
+			reg = <0x3025000 0x1000>;
+
+			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			in-ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					merge_funnel_in0: endpoint {
+						remote-endpoint =
+						  <&funnel0_out>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					merge_funnel_in1: endpoint {
+						remote-endpoint =
+						  <&funnel1_out>;
+					};
+				};
+			};
+
+			out-ports {
+				port {
+					merge_funnel_out: endpoint {
+						remote-endpoint =
+						  <&etf_in>;
+					};
+				};
+			};
+		};
+
+		replicator@3026000 {
+			compatible = "arm,coresight-dynamic-replicator", "arm,primecell";
+			reg = <0x3026000 0x1000>;
+
+			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			in-ports {
+				port {
+					replicator_in: endpoint {
+						remote-endpoint =
+						  <&etf_out>;
+					};
+				};
+			};
+
+			out-ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					replicator_out0: endpoint {
+						remote-endpoint =
+						  <&etr_in>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					replicator_out1: endpoint {
+						remote-endpoint =
+						  <&tpiu_in>;
+					};
+				};
+			};
+		};
+
+		etf@3027000 {
+			compatible = "arm,coresight-tmc", "arm,primecell";
+			reg = <0x3027000 0x1000>;
+
+			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			in-ports {
+				port {
+					etf_in: endpoint {
+						remote-endpoint =
+						  <&merge_funnel_out>;
+					};
+				};
+			};
+
+			out-ports {
+				port {
+					etf_out: endpoint {
+						remote-endpoint =
+						  <&replicator_in>;
+					};
+				};
+			};
+		};
+
+		etr@3028000 {
+			compatible = "arm,coresight-tmc", "arm,primecell";
+			reg = <0x3028000 0x1000>;
+
+			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+			arm,scatter-gather;
+
+			in-ports {
+				port {
+					etr_in: endpoint {
+						remote-endpoint =
+						  <&replicator_out0>;
+					};
+				};
+			};
+		};
+
+		debug@3810000 {
+			compatible = "arm,coresight-cpu-debug", "arm,primecell";
+			reg = <0x3810000 0x1000>;
+
+			clocks = <&rpmcc RPM_QDSS_CLK>;
+			clock-names = "apb_pclk";
+
+			cpu = <&CPU0>;
+		};
+
+		etm@3840000 {
+			compatible = "arm,coresight-etm4x", "arm,primecell";
+			reg = <0x3840000 0x1000>;
+
+			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			cpu = <&CPU0>;
+
+			out-ports {
+				port {
+					etm0_out: endpoint {
+						remote-endpoint =
+						  <&apss_funnel0_in0>;
+					};
+				};
+			};
+		};
+
+		debug@3910000 {
+			compatible = "arm,coresight-cpu-debug", "arm,primecell";
+			reg = <0x3910000 0x1000>;
+
+			clocks = <&rpmcc RPM_QDSS_CLK>;
+			clock-names = "apb_pclk";
+
+			cpu = <&CPU1>;
+		};
+
+		etm@3940000 {
+			compatible = "arm,coresight-etm4x", "arm,primecell";
+			reg = <0x3940000 0x1000>;
+
+			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			cpu = <&CPU1>;
+
+			out-ports {
+				port {
+					etm1_out: endpoint {
+						remote-endpoint =
+						  <&apss_funnel0_in1>;
+					};
+				};
+			};
+		};
+
+		funnel@39b0000 { /* APSS Funnel 0 */
+			compatible = "arm,coresight-funnel", "arm,primecell";
+			reg = <0x39b0000 0x1000>;
+
+			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			in-ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					apss_funnel0_in0: endpoint {
+						remote-endpoint = <&etm0_out>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					apss_funnel0_in1: endpoint {
+						remote-endpoint = <&etm1_out>;
+					};
+				};
+			};
+
+			out-ports {
+				port {
+					apss_funnel0_out: endpoint {
+						remote-endpoint =
+						  <&apss_merge_funnel_in0>;
+					};
+				};
+			};
+		};
+
+		debug@3a10000 {
+			compatible = "arm,coresight-cpu-debug", "arm,primecell";
+			reg = <0x3a10000 0x1000>;
+
+			clocks = <&rpmcc RPM_QDSS_CLK>;
+			clock-names = "apb_pclk";
+
+			cpu = <&CPU2>;
+		};
+
+		etm@3a40000 {
+			compatible = "arm,coresight-etm4x", "arm,primecell";
+			reg = <0x3a40000 0x1000>;
+
+			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			cpu = <&CPU2>;
+
+			out-ports {
+				port {
+					etm2_out: endpoint {
+						remote-endpoint =
+						  <&apss_funnel1_in0>;
+					};
+				};
+			};
+		};
+
+		debug@3b10000 {
+			compatible = "arm,coresight-cpu-debug", "arm,primecell";
+			reg = <0x3b10000 0x1000>;
+
+			clocks = <&rpmcc RPM_QDSS_CLK>;
+			clock-names = "apb_pclk";
+
+			cpu = <&CPU3>;
+		};
+
+		etm@3b40000 {
+			compatible = "arm,coresight-etm4x", "arm,primecell";
+			reg = <0x3b40000 0x1000>;
+
+			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			cpu = <&CPU3>;
+
+			out-ports {
+				port {
+					etm3_out: endpoint {
+						remote-endpoint =
+						  <&apss_funnel1_in1>;
+					};
+				};
+			};
+		};
+
+		funnel@3bb0000 { /* APSS Funnel 1 */
+			compatible = "arm,coresight-funnel", "arm,primecell";
+			reg = <0x3bb0000 0x1000>;
+
+			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			in-ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					apss_funnel1_in0: endpoint {
+						remote-endpoint = <&etm2_out>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					apss_funnel1_in1: endpoint {
+						remote-endpoint = <&etm3_out>;
+					};
+				};
+			};
+
+			out-ports {
+				port {
+					apss_funnel1_out: endpoint {
+						remote-endpoint =
+						  <&apss_merge_funnel_in1>;
+					};
+				};
+			};
+		};
+
+		funnel@3bc0000 {
+			compatible = "arm,coresight-funnel", "arm,primecell";
+			reg = <0x3bc0000 0x1000>;
+
+			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			in-ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					apss_merge_funnel_in0: endpoint {
+						remote-endpoint =
+						  <&apss_funnel0_out>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					apss_merge_funnel_in1: endpoint {
+						remote-endpoint =
+						  <&apss_funnel1_out>;
+					};
+				};
+			};
+
+			out-ports {
+				port {
+					apss_merge_funnel_out: endpoint {
+						remote-endpoint =
+						  <&funnel1_in>;
+					};
+				};
+			};
+		};
+
 		kryocc: clock-controller@6400000 {
 			compatible = "qcom,apcc-msm8996";
 			reg = <0x6400000 0x90000>;
Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
#6 lore raw

PATCH v5 4/7 coresight: etm4x: Add support to enable ETMv4.2

In reply to Sai Prakash Ranjan

SDM845 has ETMv4.2 and can use the existing etm4x driver. But the current etm driver checks only for ETMv4.0 and errors out for other etm4x versions. This patch adds this missing support to enable SoC's with ETMv4x to use same driver by checking only the ETM architecture major version number.

Without this change, we get below error during etm probe:

/ # dmesg | grep etm

[    6.660093] coresight-etm4x: probe of 7040000.etm failed with error -22
[    6.666902] coresight-etm4x: probe of 7140000.etm failed with error -22
[    6.673708] coresight-etm4x: probe of 7240000.etm failed with error -22
[    6.680511] coresight-etm4x: probe of 7340000.etm failed with error -22
[    6.687313] coresight-etm4x: probe of 7440000.etm failed with error -22
[    6.694113] coresight-etm4x: probe of 7540000.etm failed with error -22
[    6.700914] coresight-etm4x: probe of 7640000.etm failed with error -22
[    6.707717] coresight-etm4x: probe of 7740000.etm failed with error -22

With this change, etm probe is successful:

/ # dmesg | grep etm

[    6.659198] coresight-etm4x 7040000.etm: CPU0: ETM v4.2 initialized
[    6.665848] coresight-etm4x 7140000.etm: CPU1: ETM v4.2 initialized
[    6.672493] coresight-etm4x 7240000.etm: CPU2: ETM v4.2 initialized
[    6.679129] coresight-etm4x 7340000.etm: CPU3: ETM v4.2 initialized
[    6.685770] coresight-etm4x 7440000.etm: CPU4: ETM v4.2 initialized
[    6.692403] coresight-etm4x 7540000.etm: CPU5: ETM v4.2 initialized
[    6.699024] coresight-etm4x 7640000.etm: CPU6: ETM v4.2 initialized
[    6.705646] coresight-etm4x 7740000.etm: CPU7: ETM v4.2 initialized
---
 drivers/hwtracing/coresight/coresight-etm4x.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/hwtracing/coresight/coresight-etm4x.c +2 -1
index 53e2fb6e86f6..fe76b176974a 100644
@@ -55,7 +55,8 @@ static void etm4_os_unlock(struct etmv4_drvdata *drvdata)
 
 static bool etm4_arch_supported(u8 arch)
 {
-	switch (arch) {
+	/* Mask out the minor version number */
+	switch (arch & 0xf0) {
 	case ETM_ARCH_V4:
 		break;
 	default:
Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
maintainer Reviewed-by on v5 4/7
#7 lore raw

Re: [PATCHv5 4/7] coresight: etm4x: Add support to enable ETMv4.2

Quoted 42 lines · Sai Prakash Ranjan

SDM845 has ETMv4.2 and can use the existing etm4x driver. But the current etm driver checks only for ETMv4.0 and errors out for other etm4x versions. This patch adds this missing support to enable SoC's with ETMv4x to use same driver by checking only the ETM architecture major version number.

Without this change, we get below error during etm probe:

/ # dmesg | grep etm

[    6.660093] coresight-etm4x: probe of 7040000.etm failed with error -22
[    6.666902] coresight-etm4x: probe of 7140000.etm failed with error -22
[    6.673708] coresight-etm4x: probe of 7240000.etm failed with error -22
[    6.680511] coresight-etm4x: probe of 7340000.etm failed with error -22
[    6.687313] coresight-etm4x: probe of 7440000.etm failed with error -22
[    6.694113] coresight-etm4x: probe of 7540000.etm failed with error -22
[    6.700914] coresight-etm4x: probe of 7640000.etm failed with error -22
[    6.707717] coresight-etm4x: probe of 7740000.etm failed with error -22

With this change, etm probe is successful:

/ # dmesg | grep etm

[    6.659198] coresight-etm4x 7040000.etm: CPU0: ETM v4.2 initialized
[    6.665848] coresight-etm4x 7140000.etm: CPU1: ETM v4.2 initialized
[    6.672493] coresight-etm4x 7240000.etm: CPU2: ETM v4.2 initialized
[    6.679129] coresight-etm4x 7340000.etm: CPU3: ETM v4.2 initialized
[    6.685770] coresight-etm4x 7440000.etm: CPU4: ETM v4.2 initialized
[    6.692403] coresight-etm4x 7540000.etm: CPU5: ETM v4.2 initialized
[    6.699024] coresight-etm4x 7640000.etm: CPU6: ETM v4.2 initialized
[    6.705646] coresight-etm4x 7740000.etm: CPU7: ETM v4.2 initialized
---
  drivers/hwtracing/coresight/coresight-etm4x.c | 3 ++-
  1 file changed, 2 insertions(+), 1 deletion(-)
drivers/hwtracing/coresight/coresight-etm4x.c +0 -0
index 53e2fb6e86f6..fe76b176974a 100644

drivers/hwtracing/coresight/coresight-etm4x.c static void etm4_os_unlock(struct etmv4_drvdata *drvdata) · line 62

Quoted 9 lines
drivers/hwtracing/coresight/coresight-etm4x.c +2 -1
@@ -55,7 +55,8 @@ static void etm4_os_unlock(struct etmv4_drvdata *drvdata)
 
  static bool etm4_arch_supported(u8 arch)
  {
-	switch (arch) {
+	/* Mask out the minor version number */
+	switch (arch & 0xf0) {
  	case ETM_ARCH_V4:
  		break;
  	default:
#8 lore raw

Re: [PATCHv5 4/7] coresight: etm4x: Add support to enable ETMv4.2

Quoted 5 lines · Suzuki K Poulose

Thanks Suzuki.

Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
#9 lore raw

PATCH v5 5/7 coresight: etm4x: Add ETM PIDs for SDM845 and MSM8996

In reply to Sai Prakash Ranjan

Instead of overriding the peripheral id(PID) check in AMBA by hardcoding them in DT, add the PIDs to the ETM4x driver. Here we use Unique Component Identifier(UCI) for MSM8996 since the ETM and CPU debug module shares the same PIDs. SDM845 does not support CPU debug module.

---
This patch depends on UCI support by Mike Leach in below link:
https://lore.kernel.org/lkml/[email protected]/

---
 drivers/hwtracing/coresight/coresight-etm4x.c | 4 ++++
 1 file changed, 4 insertions(+)
drivers/hwtracing/coresight/coresight-etm4x.c +4 -0
index fe76b176974a..17731a8ae787 100644
@@ -1080,6 +1080,10 @@ static const struct amba_id etm4_ids[] = {
 	ETM4x_AMBA_ID(0x000bb95a),		/* Cortex-A72 */
 	ETM4x_AMBA_ID(0x000bb959),		/* Cortex-A73 */
 	ETM4x_AMBA_ID(0x000bb9da),		/* Cortex-A35 */
+	ETM4x_AMBA_UCI_ID(0x000f0205),		/* Qualcomm Kryo */
+	ETM4x_AMBA_UCI_ID(0x000f0211),		/* Qualcomm Kryo */
+	ETM4x_AMBA_ID(0x000bb802),		/* Qualcomm Kryo 385 Cortex-A55 */
+	ETM4x_AMBA_ID(0x000bb803),		/* Qualcomm Kryo 385 Cortex-A75 */
 	{},
 };
 
Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
maintainer Reviewed-by on v5 5/7
#10 lore raw

Re: [PATCHv5 5/7] coresight: etm4x: Add ETM PIDs for SDM845 and MSM8996

Quoted 20 lines · Sai Prakash Ranjan

Instead of overriding the peripheral id(PID) check in AMBA by hardcoding them in DT, add the PIDs to the ETM4x driver. Here we use Unique Component Identifier(UCI) for MSM8996 since the ETM and CPU debug module shares the same PIDs. SDM845 does not support CPU debug module.

---
This patch depends on UCI support by Mike Leach in below link:
https://lore.kernel.org/lkml/[email protected]/

---
  drivers/hwtracing/coresight/coresight-etm4x.c | 4 ++++
  1 file changed, 4 insertions(+)
drivers/hwtracing/coresight/coresight-etm4x.c +0 -0
index fe76b176974a..17731a8ae787 100644

drivers/hwtracing/coresight/coresight-etm4x.c static const struct amba_id etm4_ids[] = { · line 1089

Quoted 10 lines
drivers/hwtracing/coresight/coresight-etm4x.c +4 -0
@@ -1080,6 +1080,10 @@ static const struct amba_id etm4_ids[] = {
  	ETM4x_AMBA_ID(0x000bb95a),		/* Cortex-A72 */
  	ETM4x_AMBA_ID(0x000bb959),		/* Cortex-A73 */
  	ETM4x_AMBA_ID(0x000bb9da),		/* Cortex-A35 */
+	ETM4x_AMBA_UCI_ID(0x000f0205),		/* Qualcomm Kryo */
+	ETM4x_AMBA_UCI_ID(0x000f0211),		/* Qualcomm Kryo */
+	ETM4x_AMBA_ID(0x000bb802),		/* Qualcomm Kryo 385 Cortex-A55 */
+	ETM4x_AMBA_ID(0x000bb803),		/* Qualcomm Kryo 385 Cortex-A75 */
  	{},
  };
 
#11 lore raw

PATCH v5 6/7 coresight: debug: Add Unique Component Identifier (UCI) table

In reply to Sai Prakash Ranjan

Add UCI table and a helper macro for coresight CPU debug module. This patch adds the UCI entries for Krypo CPUs found on MSM8996 which shares the same PIDs as ETMs.

Without this, below error is observed on MSM8996:

[    5.429867] OF: graph: no port node found in /soc/debug@3810000
[    5.429938] coresight-etm4x: probe of 3810000.debug failed with error -22
[    5.435415] coresight-cpu-debug 3810000.debug: Coresight debug-CPU0 initialized
[    5.446474] OF: graph: no port node found in /soc/debug@3910000
[    5.448927] coresight-etm4x: probe of 3910000.debug failed with error -22
[    5.454681] coresight-cpu-debug 3910000.debug: Coresight debug-CPU1 initialized
[    5.487765] OF: graph: no port node found in /soc/debug@3a10000
[    5.488007] coresight-etm4x: probe of 3a10000.debug failed with error -22
[    5.493024] coresight-cpu-debug 3a10000.debug: Coresight debug-CPU2 initialized
[    5.501802] OF: graph: no port node found in /soc/debug@3b10000
[    5.512901] coresight-etm4x: probe of 3b10000.debug failed with error -22
[    5.513192] coresight-cpu-debug 3b10000.debug: Coresight debug-CPU3 initialized

Also add a helper macro to make adding CPU PIDs easier similar to ETM4X driver.

---
This patch depends on UCI support by Mike Leach in below link:
https://lore.kernel.org/lkml/[email protected]/

---
 .../hwtracing/coresight/coresight-cpu-debug.c | 41 +++++++++++++------
 1 file changed, 28 insertions(+), 13 deletions(-)
drivers/hwtracing/coresight/coresight-cpu-debug.c +28 -13
index 45b2460f3166..a126ed0b9a76 100644
@@ -655,20 +655,35 @@ static int debug_remove(struct amba_device *adev)
 	return 0;
 }
 
+#define DEBUG_AMBA_ID(pid)			\
+	{					\
+		.id	= pid,			\
+		.mask	= 0x000fffff,		\
+	}
+
+static struct amba_cs_uci_id uci_id_debug[] = {
+	{
+		/*  CPU Debug UCI data */
+		.devarch	= 0x47706a15,
+		.devarch_mask	= 0xfff0ffff,
+		.devtype	= 0x00000015,
+	}
+};
+
+#define DEBUG_AMBA_UCI_ID(pid)			\
+	{					\
+		.id	= pid,			\
+		.mask	= 0x000fffff,		\
+		.data	= uci_id_debug,		\
+	}
+
 static const struct amba_id debug_ids[] = {
-	{       /* Debug for Cortex-A53 */
-		.id	= 0x000bbd03,
-		.mask	= 0x000fffff,
-	},
-	{       /* Debug for Cortex-A57 */
-		.id	= 0x000bbd07,
-		.mask	= 0x000fffff,
-	},
-	{       /* Debug for Cortex-A72 */
-		.id	= 0x000bbd08,
-		.mask	= 0x000fffff,
-	},
-	{ 0, 0 },
+	DEBUG_AMBA_ID(0x000bbd03),		/* Cortex-A53 */
+	DEBUG_AMBA_ID(0x000bbd07),		/* Cortex-A57 */
+	DEBUG_AMBA_ID(0x000bbd08),		/* Cortex-A72 */
+	DEBUG_AMBA_UCI_ID(0x000f0205),		/* Qualcomm Kryo */
+	DEBUG_AMBA_UCI_ID(0x000f0211),		/* Qualcomm Kryo */
+	{},
 };
 
 static struct amba_driver debug_driver = {
Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
#12 lore raw

Re: [PATCHv5 6/7] coresight: debug: Add Unique Component Identifier (UCI) table

Quoted 19 lines · Sai Prakash Ranjan

Add UCI table and a helper macro for coresight CPU debug module. This patch adds the UCI entries for Krypo CPUs found on MSM8996 which shares the same PIDs as ETMs.

Without this, below error is observed on MSM8996:

[    5.429867] OF: graph: no port node found in /soc/debug@3810000
[    5.429938] coresight-etm4x: probe of 3810000.debug failed with error -22
[    5.435415] coresight-cpu-debug 3810000.debug: Coresight debug-CPU0 initialized
[    5.446474] OF: graph: no port node found in /soc/debug@3910000
[    5.448927] coresight-etm4x: probe of 3910000.debug failed with error -22
[    5.454681] coresight-cpu-debug 3910000.debug: Coresight debug-CPU1 initialized
[    5.487765] OF: graph: no port node found in /soc/debug@3a10000
[    5.488007] coresight-etm4x: probe of 3a10000.debug failed with error -22
[    5.493024] coresight-cpu-debug 3a10000.debug: Coresight debug-CPU2 initialized
[    5.501802] OF: graph: no port node found in /soc/debug@3b10000
[    5.512901] coresight-etm4x: probe of 3b10000.debug failed with error -22
[    5.513192] coresight-cpu-debug 3b10000.debug: Coresight debug-CPU3 initialized
Quoted 4 lines

Also add a helper macro to make adding CPU PIDs easier similar to ETM4X driver.

Looks good to me and tested on my Hikey board (though I cannot test for a device with UCI ID):

Reviewed-and-tested-by Leo Yan <[email protected]>
Quoted 64 lines

---
This patch depends on UCI support by Mike Leach in below link:
https://lore.kernel.org/lkml/[email protected]/

---
 .../hwtracing/coresight/coresight-cpu-debug.c | 41 +++++++++++++------
 1 file changed, 28 insertions(+), 13 deletions(-)
drivers/hwtracing/coresight/coresight-cpu-debug.c +28 -13
index 45b2460f3166..a126ed0b9a76 100644
@@ -655,20 +655,35 @@ static int debug_remove(struct amba_device *adev)
 	return 0;
 }
 
+#define DEBUG_AMBA_ID(pid)			\
+	{					\
+		.id	= pid,			\
+		.mask	= 0x000fffff,		\
+	}
+
+static struct amba_cs_uci_id uci_id_debug[] = {
+	{
+		/*  CPU Debug UCI data */
+		.devarch	= 0x47706a15,
+		.devarch_mask	= 0xfff0ffff,
+		.devtype	= 0x00000015,
+	}
+};
+
+#define DEBUG_AMBA_UCI_ID(pid)			\
+	{					\
+		.id	= pid,			\
+		.mask	= 0x000fffff,		\
+		.data	= uci_id_debug,		\
+	}
+
 static const struct amba_id debug_ids[] = {
-	{       /* Debug for Cortex-A53 */
-		.id	= 0x000bbd03,
-		.mask	= 0x000fffff,
-	},
-	{       /* Debug for Cortex-A57 */
-		.id	= 0x000bbd07,
-		.mask	= 0x000fffff,
-	},
-	{       /* Debug for Cortex-A72 */
-		.id	= 0x000bbd08,
-		.mask	= 0x000fffff,
-	},
-	{ 0, 0 },
+	DEBUG_AMBA_ID(0x000bbd03),		/* Cortex-A53 */
+	DEBUG_AMBA_ID(0x000bbd07),		/* Cortex-A57 */
+	DEBUG_AMBA_ID(0x000bbd08),		/* Cortex-A72 */
+	DEBUG_AMBA_UCI_ID(0x000f0205),		/* Qualcomm Kryo */
+	DEBUG_AMBA_UCI_ID(0x000f0211),		/* Qualcomm Kryo */
+	{},
 };
 
 static struct amba_driver debug_driver = {
Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
#13 lore raw

Re: [PATCHv5 6/7] coresight: debug: Add Unique Component Identifier (UCI) table

Quoted 23 lines · Leo Yan
Quoted 22 lines · Sai Prakash Ranjan

Add UCI table and a helper macro for coresight CPU debug module. This patch adds the UCI entries for Krypo CPUs found on MSM8996 which shares the same PIDs as ETMs.

Without this, below error is observed on MSM8996:

[    5.429867] OF: graph: no port node found in /soc/debug@3810000
[    5.429938] coresight-etm4x: probe of 3810000.debug failed with error -22
[    5.435415] coresight-cpu-debug 3810000.debug: Coresight debug-CPU0 initialized
[    5.446474] OF: graph: no port node found in /soc/debug@3910000
[    5.448927] coresight-etm4x: probe of 3910000.debug failed with error -22
[    5.454681] coresight-cpu-debug 3910000.debug: Coresight debug-CPU1 initialized
[    5.487765] OF: graph: no port node found in /soc/debug@3a10000
[    5.488007] coresight-etm4x: probe of 3a10000.debug failed with error -22
[    5.493024] coresight-cpu-debug 3a10000.debug: Coresight debug-CPU2 initialized
[    5.501802] OF: graph: no port node found in /soc/debug@3b10000
[    5.512901] coresight-etm4x: probe of 3b10000.debug failed with error -22
[    5.513192] coresight-cpu-debug 3b10000.debug: Coresight debug-CPU3 initialized

Also add a helper macro to make adding CPU PIDs easier similar to ETM4X driver.

Quoted 6 lines
Quoted 1 line

Looks good to me and tested on my Hikey board (though I cannot test for a device with UCI ID):

Reviewed-and-tested-by Leo Yan <[email protected]>

I just now found if apply this patch onto coresight next branch [1], it will conflict with patch 'coresight: cpu-debug: Support for CA73 CPUs' [2]. Sorry if introduce regression by this.

Hi Mathieu, could you confirm should apply this patch onto to coresight next branch?

[...]

Thanks,
Leo Yan

[1] https://git.linaro.org/kernel/coresight.git/log/?h=next
[2] https://git.linaro.org/kernel/coresight.git/commit/?h=next&id=14420b405d03cd160b5ace283693ce5b1cf273fa

#14 lore raw

Re: [PATCHv5 6/7] coresight: debug: Add Unique Component Identifier (UCI) table

Hi Leo,

Quoted 5 lines · Leo Yan

I just now found if apply this patch onto coresight next branch [1], it will conflict with patch 'coresight: cpu-debug: Support for CA73 CPUs' [2]. Sorry if introduce regression by this.

This patch depends on UCI support which is being discussed at:

https://lore.kernel.org/lkml/[email protected]/

So I think this should not go into coresight-next until the UCI support is merged into coresight-next as well.

If UCI support is already merged, then I can rebase this patch on top of coresight-next and resend.

Thanks,
Sai

Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
#15 lore raw

Re: [PATCHv5 6/7] coresight: debug: Add Unique Component Identifier (UCI) table

In reply to Leo Yan
Quoted 6 lines · Leo Yan

Looks good to me and tested on my Hikey board (though I cannot test for a device with UCI ID):

Reviewed-and-tested-by Leo Yan <[email protected]>

Thanks Leo.

Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
#16 lore raw

PATCH v5 7/7 arm64: dts: qcom: sdm845: Remove the duplicate header inclusion

In reply to Sai Prakash Ranjan

Remove the duplicate inclusion of qcom,gcc-sdm845.h mistakenly introduced by commit 6e17f8140521 ("arm64:
dts: sdm845: add prng-ee node").

---
 arch/arm64/boot/dts/qcom/sdm845.dtsi | 1 -
 1 file changed, 1 deletion(-)
arch/arm64/boot/dts/qcom/sdm845.dtsi +0 -1
index e49f71d00854..eafe8e47471e 100644
@@ -12,7 +12,6 @@
 #include <dt-bindings/phy/phy-qcom-qusb2.h>
 #include <dt-bindings/reset/qcom,sdm845-aoss.h>
 #include <dt-bindings/soc/qcom,rpmh-rsc.h>
-#include <dt-bindings/clock/qcom,gcc-sdm845.h>
 
 / {
 	interrupt-parent = <&intc>;
Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
#17 lore raw

Re: [PATCHv5 7/7] arm64: dts: qcom: sdm845: Remove the duplicate header inclusion

Hi,

Quoted 16 lines · Sai Prakash Ranjan

Remove the duplicate inclusion of qcom,gcc-sdm845.h mistakenly introduced by commit 6e17f8140521 ("arm64:
dts: sdm845: add prng-ee node").

---
 arch/arm64/boot/dts/qcom/sdm845.dtsi | 1 -
 1 file changed, 1 deletion(-)
arch/arm64/boot/dts/qcom/sdm845.dtsi +0 -0
index e49f71d00854..eafe8e47471e 100644

arch/arm64/boot/dts/qcom/sdm845.dtsi line 15

Quoted 4 lines
arch/arm64/boot/dts/qcom/sdm845.dtsi +0 -1
@@ -12,7 +12,6 @@
 #include <dt-bindings/phy/phy-qcom-qusb2.h>
 #include <dt-bindings/reset/qcom,sdm845-aoss.h>
 #include <dt-bindings/soc/qcom,rpmh-rsc.h>
-#include <dt-bindings/clock/qcom,gcc-sdm845.h>

You can probably stop sending this one. It's in Andy's tree now. See commit ea0edd7e63f4 ("arm64: dts: qcom: sdm845: Remove the duplicate header inclusion").

#18 lore raw

Re: [PATCHv5 7/7] arm64: dts: qcom: sdm845: Remove the duplicate header inclusion

Hi Doug,

Quoted 5 lines · Doug Anderson

Hi,

You can probably stop sending this one. It's in Andy's tree now. See commit ea0edd7e63f4 ("arm64: dts: qcom: sdm845: Remove the duplicate header inclusion").

Sorry, missed this one.

#19 lore raw
In reply to Sai Prakash Ranjan
Quoted 8 lines · Sai Prakash Ranjan

This patch series adds support for coresight on SDM845, MSM8998, and MSM8996.

Patch 2 adds device tree nodes for MSM8998 coresight components.

Patch 2 depends on MSM8998 rpm clocks and rpmcc nodes:
https://lore.kernel.org/lkml/[email protected]/
https://lore.kernel.org/lkml/[email protected]/

Quoted 7 lines

This patch series has been tested on SDM845 MTP and MSM8996 based Dragonboard 820c and MSM8998 MTP.

v5:
* Added coresight support for MSM8998.
* Added ETM PIDs for SDM845 and MSM8996 as suggested by Suzuki.
* Added UCI table for Coresight CPU debug module.

Great! Thanks :-)