dmaengine: Add Synopsys eDMA IP driver (version 0)
Subsystems (5)
cover dmaengine: Add Synopsys eDMA IP driver (version 0)
Add Synopsys eDMA IP driver (version 0 and for EP side only) to Linux kernel. This IP is generally distributed with Synopsys PCIe EndPoint IP (depends of the use and licensing agreement), which supports:
- legacy and unroll modes
- 16 independent and concurrent channels (8 write + 8 read)
- supports linked list (scatter-gather) transfer
- each linked list descriptor can transfer from 1 byte to 4 Gbytes
- supports cyclic transfer
- PCIe EndPoint glue-logic
This patch series contains:
- eDMA core + eDMA core v0 driver (implements the interface with DMAengine controller APIs and interfaces with eDMA HW block)
- eDMA PCIe glue-logic reference driver (attaches to Synopsys EP and provides memory access to eDMA core driver)
Gustavo Pimentel (6):
dmaengine: Add Synopsys eDMA IP core driver
dmaengine: Add Synopsys eDMA IP version 0 support
dmaengine: Add Synopsys eDMA IP version 0 debugfs support
PCI: Add Synopsys endpoint EDDA Device ID
dmaengine: Add Synopsys eDMA IP PCIe glue-logic
MAINTAINERS: Add Synopsys eDMA IP driver maintainer
MAINTAINERS | 7 + drivers/dma/Kconfig | 2 + drivers/dma/Makefile | 1 + drivers/dma/dw-edma/Kconfig | 18 + drivers/dma/dw-edma/Makefile | 7 + drivers/dma/dw-edma/dw-edma-core.c | 937 +++++++++++++++++++++++++++++++ drivers/dma/dw-edma/dw-edma-core.h | 165 ++++++ drivers/dma/dw-edma/dw-edma-pcie.c | 229 ++++++++ drivers/dma/dw-edma/dw-edma-v0-core.c | 354 ++++++++++++ drivers/dma/dw-edma/dw-edma-v0-core.h | 28 + drivers/dma/dw-edma/dw-edma-v0-debugfs.c | 310 ++++++++++ drivers/dma/dw-edma/dw-edma-v0-debugfs.h | 27 + drivers/dma/dw-edma/dw-edma-v0-regs.h | 158 ++++++ drivers/misc/pci_endpoint_test.c | 2 +- include/linux/dma/edma.h | 47 ++ include/linux/pci_ids.h | 1 + 16 files changed, 2292 insertions(+), 1 deletion(-) create mode 100644 drivers/dma/dw-edma/Kconfig create mode 100644 drivers/dma/dw-edma/Makefile create mode 100644 drivers/dma/dw-edma/dw-edma-core.c create mode 100644 drivers/dma/dw-edma/dw-edma-core.h create mode 100644 drivers/dma/dw-edma/dw-edma-pcie.c create mode 100644 drivers/dma/dw-edma/dw-edma-v0-core.c create mode 100644 drivers/dma/dw-edma/dw-edma-v0-core.h create mode 100644 drivers/dma/dw-edma/dw-edma-v0-debugfs.c create mode 100644 drivers/dma/dw-edma/dw-edma-v0-debugfs.h create mode 100644 drivers/dma/dw-edma/dw-edma-v0-regs.h create mode 100644 include/linux/dma/edma.h
Signature · 1 line
2.7.4
PATCH 1/6 dmaengine: Add Synopsys eDMA IP core driver
Add Synopsys PCIe Endpoint eDMA IP core driver to kernel.
This IP is generally distributed with Synopsys PCIe Endpoint IP (depends of the use and licensing agreement).
This core driver, initializes and configures the eDMA IP using vma-helpers functions and dma-engine subsystem.
This driver can be compile as built-in or external module in kernel.
To enable this driver just select DW_EDMA option in kernel configuration, however it requires and selects automatically DMA_ENGINE and DMA_VIRTUAL_CHANNELS option too.
In order to transfer data from point A to B as fast as possible this IP requires a dedicated memory space containing linked list of elements.
All elements of this linked list are continuous and each one describes a data transfer (source and destination addresses, length and a control variable).
For the sake of simplicity, lets assume a memory space for channel write 0 which allows about 42 elements.
+---------+
| Desc #0 |-+
+---------+ |
V
+----------+
| Chunk #0 |-+
| CB = 1 | | +----------+ +-----+ +-----------+ +-----+
+----------+ +->| Burst #0 |->| ... |->| Burst #41 |->| llp |
| +----------+ +-----+ +-----------+ +-----+
V
+----------+
| Chunk #1 |-+
| CB = 0 | | +-----------+ +-----+ +-----------+ +-----+
+----------+ +->| Burst #42 |->| ... |->| Burst #83 |->| llp |
| +-----------+ +-----+ +-----------+ +-----+
V
+----------+
| Chunk #2 |-+
| CB = 1 | | +-----------+ +-----+ +------------+ +-----+
+----------+ +->| Burst #84 |->| ... |->| Burst #125 |->| llp |
| +-----------+ +-----+ +------------+ +-----+
V
+----------+
| Chunk #3 |-+
| CB = 0 | | +------------+ +-----+ +------------+ +-----+
+----------+ +->| Burst #126 |->| ... |->| Burst #129 |->| llp |
+------------+ +-----+ +------------+ +-----+Legend:
- Linked list, also know as Chunk
- Linked list element*, also know as Burst *CB*, also know as Change Bit,
it's a control bit (and typically is toggled) that allows to easily identify and differentiate between the current linked list and the previous or the next one.
- LLP, is a special element that indicates the end of the linked list
element stream also informs that the next CB should be toggle
On every last Burst of the Chunk (Burst #41, Burst #83, Burst #125 or even Burst #129) is set some flags on their control variable (RIE and LIE bits) that will trigger the send of "done" interruption.
On the interruptions callback, is decided whether to recycle the linked list memory space by writing a new set of Bursts elements (if still exists Chunks to transfer) or is considered completed (if there is no Chunks available to transfer).
On scatter-gather transfer mode, the client will submit a scatter-gather list of n (on this case 130) elements, that will be divide in multiple Chunks, each Chunk will have (on this case 42) a limited number of Bursts and after transferring all Bursts, an interrupt will be triggered, which will allow to recycle the all linked list dedicated memory again with the new information relative to the next Chunk and respective Burst associated and repeat the whole cycle again.
On cyclic transfer mode, the client will submit a buffer pointer, length of it and number of repetitions, in this case each burst will correspond directly to each repetition.
Each Burst can describes a data transfer from point A(source) to point B(destination) with a length that can be from 1 byte up to 4 GB. Since dedicated the memory space where the linked list will reside is limited, the whole n burst elements will be organized in several Chunks, that will be used later to recycle the dedicated memory space to initiate a new sequence of data transfers.
The whole transfer is considered has completed when it was transferred all bursts.
Currently this IP has a set well-known register map, which includes support for legacy and unroll modes. Legacy mode is version of this register map that has multiplexer register that allows to switch registers between all write and read channels and the unroll modes repeats all write and read channels registers with an offset between them. This register map is called v0.
The IP team is creating a new register map more suitable to the latest PCIe features, that very likely will change the map register, which this version will be called v1. As soon as this new version is released by the IP team the support for this version in be included on this driver.
According to the logic, patches 1, 2 and 3 should be squashed into 1 unique patch, but for the sake of simplicity of review, it was divided in this 3 patches files.
--- drivers/dma/Kconfig | 2 + drivers/dma/Makefile | 1 + drivers/dma/dw-edma/Kconfig | 9 + drivers/dma/dw-edma/Makefile | 4 + drivers/dma/dw-edma/dw-edma-core.c | 936 +++++++++++++++++++++++++++++++++++++ drivers/dma/dw-edma/dw-edma-core.h | 165 +++++++ include/linux/dma/edma.h | 47 ++ 7 files changed, 1164 insertions(+) create mode 100644 drivers/dma/dw-edma/Kconfig create mode 100644 drivers/dma/dw-edma/Makefile create mode 100644 drivers/dma/dw-edma/dw-edma-core.c create mode 100644 drivers/dma/dw-edma/dw-edma-core.h create mode 100644 include/linux/dma/edma.h
drivers/dma/Kconfig +2 -0
@@ -665,6 +665,8 @@ source "drivers/dma/qcom/Kconfig" source "drivers/dma/dw/Kconfig" +source "drivers/dma/dw-edma/Kconfig" + source "drivers/dma/hsu/Kconfig" source "drivers/dma/sh/Kconfig"
drivers/dma/Makefile +1 -0
@@ -29,6 +29,7 @@ obj-$(CONFIG_DMA_SUN4I) += sun4i-dma.o obj-$(CONFIG_DMA_SUN6I) += sun6i-dma.o obj-$(CONFIG_DW_AXI_DMAC) += dw-axi-dmac/ obj-$(CONFIG_DW_DMAC_CORE) += dw/ +obj-$(CONFIG_DW_EDMA) += dw-edma/ obj-$(CONFIG_EP93XX_DMA) += ep93xx_dma.o obj-$(CONFIG_FSL_DMA) += fsldma.o obj-$(CONFIG_FSL_EDMA) += fsl-edma.o fsl-edma-common.o
drivers/dma/dw-edma/Kconfig new file +9 -0
@@ -0,0 +1,9 @@ +# SPDX-License-Identifier: GPL-2.0 + +config DW_EDMA + tristate "Synopsys DesignWare eDMA controller driver" + select DMA_ENGINE + select DMA_VIRTUAL_CHANNELS + help + Support the Synopsys DesignWare eDMA controller, normally + implemented on endpoints SoCs.
drivers/dma/dw-edma/Makefile new file +4 -0
@@ -0,0 +1,4 @@ +# SPDX-License-Identifier: GPL-2.0 + +obj-$(CONFIG_DW_EDMA) += dw-edma.o +dw-edma-objs := dw-edma-core.o
drivers/dma/dw-edma/dw-edma-core.c new file +936 -0
936 lines not on this page · raw message
drivers/dma/dw-edma/dw-edma-core.h new file +165 -0
165 lines not on this page · raw message
include/linux/dma/edma.h new file +47 -0
47 lines not on this page · raw message
Signature · 1 line
2.7.4
PATCH 2/6 dmaengine: Add Synopsys eDMA IP version 0 support
In reply to Gustavo PimentelAdd support for the eDMA IP version 0 driver for both register maps (legacy and unroll).
The legacy register mapping was the initial implementation, which consisted in having all registers belonging to channels multiplexed, which could be change anytime (which could led a race-condition) by view port register (access to only one channel available each time).
This register mapping is not very effective and efficient in a multithread environment, which has led to the development of unroll registers mapping, which consists of having all channels registers accessible any time by spreading all channels registers by an offset between them.
This version supports a maximum of 16 independent channels (8 write + 8 read), which can run simultaneously.
Implements a scatter-gather transfer through a linked list, where the size of linked list depends on the allocated memory divided equally among all channels.
Each linked list descriptor can transfer from 1 byte to 4 Gbytes and is alignmented to DWORD.
Both SAR (Source Address Register) and DAR (Destination Address Register) are alignmented to byte.
--- drivers/dma/dw-edma/Makefile | 3 +- drivers/dma/dw-edma/dw-edma-core.c | 1 + drivers/dma/dw-edma/dw-edma-v0-core.c | 352 ++++++++++++++++++++++++++++++++++ drivers/dma/dw-edma/dw-edma-v0-core.h | 28 +++ drivers/dma/dw-edma/dw-edma-v0-regs.h | 158 +++++++++++++++ 5 files changed, 541 insertions(+), 1 deletion(-) create mode 100644 drivers/dma/dw-edma/dw-edma-v0-core.c create mode 100644 drivers/dma/dw-edma/dw-edma-v0-core.h create mode 100644 drivers/dma/dw-edma/dw-edma-v0-regs.h
drivers/dma/dw-edma/Makefile +2 -1
@@ -1,4 +1,5 @@ # SPDX-License-Identifier: GPL-2.0 obj-$(CONFIG_DW_EDMA) += dw-edma.o -dw-edma-objs := dw-edma-core.o +dw-edma-objs := dw-edma-core.o \ + dw-edma-v0-core.o
drivers/dma/dw-edma/dw-edma-core.c +1 -0
@@ -17,6 +17,7 @@#include <linux/pci.h> #include "dw-edma-core.h" +#include "dw-edma-v0-core.h" #include "../dmaengine.h" #include "../virt-dma.h"
drivers/dma/dw-edma/dw-edma-v0-core.c new file +352 -0
352 lines not on this page · raw message
drivers/dma/dw-edma/dw-edma-v0-core.h new file +28 -0
@@ -0,0 +1,28 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* +* Copyright (c) 2018-2019 Synopsys, Inc. and/or its affiliates. +* Synopsys DesignWare eDMA v0 core +* +* Author: Gustavo Pimentel <[email protected]> +*/ + +#ifndef _DW_EDMA_V0_CORE_H +#define _DW_EDMA_V0_CORE_H + +#include <linux/dma/edma.h> + +/* eDMA management callbacks */ +void dw_edma_v0_core_off (struct dw_edma *chan); +u16 dw_edma_v0_core_ch_count (struct dw_edma *chan,enum dw_edma_dir dir); +enum dma_status dw_edma_v0_core_ch_status (struct dw_edma_chan *chan); +void dw_edma_v0_core_clear_done_int (struct dw_edma_chan *chan); +void dw_edma_v0_core_clear_abort_int (struct dw_edma_chan *chan); +u32 dw_edma_v0_core_status_done_int (struct dw_edma *chan,enum dw_edma_dir dir); +u32 dw_edma_v0_core_status_abort_int (struct dw_edma *chan,enum dw_edma_dir dir); +void dw_edma_v0_core_start (struct dw_edma_chunk *chunk,bool first); +int dw_edma_v0_core_device_config (struct dw_edma_chan *chan); +/* eDMA debug fs callbacks */ +void dw_edma_v0_core_debugfs_on (struct dw_edma_chip *chip); +void dw_edma_v0_core_debugfs_off (void ); + +#endif /* _DW_EDMA_V0_CORE_H */
drivers/dma/dw-edma/dw-edma-v0-regs.h new file +158 -0
158 lines not on this page · raw message
Signature · 1 line
2.7.4
PATCH 3/6 dmaengine: Add Synopsys eDMA IP version 0 debugfs support
In reply to Gustavo PimentelAdd Synopsys eDMA IP version 0 debugfs support to assist any debug in the future.
Creates a file system structure composed by folders and files that mimic the IP register map (this files are read only) to ease any debug.
To enable this feature is necessary to select DEBUG_FS option on kernel configuration.
Small output example:
(eDMA IP version 0, unroll, 1 write + 1 read channels)
% mount -t debugfs none /sys/kernel/debug/
% tree /sys/kernel/debug/dw-edma-core:0/
dw-edma/
├── version ├── mode ├── wr_ch_cnt ├── rd_ch_cnt └── registers ├── ctrl_data_arb_prior ├── ctrl ├── write │ ├── engine_en │ ├── doorbell │ ├── ch_arb_weight_low │ ├── ch_arb_weight_high │ ├── int_status │ ├── int_mask │ ├── int_clear │ ├── err_status │ ├── done_imwr_low │ ├── done_imwr_high │ ├── abort_imwr_low │ ├── abort_imwr_high │ ├── ch01_imwr_data │ ├── ch23_imwr_data │ ├── ch45_imwr_data │ ├── ch67_imwr_data │ ├── linked_list_err_en │ ├── engine_chgroup │ ├── engine_hshake_cnt_low │ ├── engine_hshake_cnt_high │ ├── ch0_pwr_en │ ├── ch1_pwr_en │ ├── ch2_pwr_en │ ├── ch3_pwr_en │ ├── ch4_pwr_en │ ├── ch5_pwr_en │ ├── ch6_pwr_en │ ├── ch7_pwr_en │ └── channel:0 │ ├── ch_control1 │ ├── ch_control2 │ ├── transfer_size │ ├── sar_low │ ├── sar_high │ ├── dar_high │ ├── llp_low │ └── llp_high └── read ├── engine_en ├── doorbell ├── ch_arb_weight_low ├── ch_arb_weight_high ├── int_status ├── int_mask ├── int_clear ├── err_status_low ├── err_status_high ├── done_imwr_low ├── done_imwr_high ├── abort_imwr_low ├── abort_imwr_high ├── ch01_imwr_data ├── ch23_imwr_data ├── ch45_imwr_data ├── ch67_imwr_data ├── linked_list_err_en ├── engine_chgroup ├── engine_hshake_cnt_low ├── engine_hshake_cnt_high ├── ch0_pwr_en ├── ch1_pwr_en ├── ch2_pwr_en ├── ch3_pwr_en ├── ch4_pwr_en ├── ch5_pwr_en ├── ch6_pwr_en ├── ch7_pwr_en └── channel:0 ├── ch_control1 ├── ch_control2 ├── transfer_size ├── sar_low ├── sar_high ├── dar_high ├── llp_low └── llp_high
--- drivers/dma/dw-edma/Makefile | 3 +- drivers/dma/dw-edma/dw-edma-v0-core.c | 2 + drivers/dma/dw-edma/dw-edma-v0-debugfs.c | 310 +++++++++++++++++++++++++++++++ drivers/dma/dw-edma/dw-edma-v0-debugfs.h | 27 +++ 4 files changed, 341 insertions(+), 1 deletion(-) create mode 100644 drivers/dma/dw-edma/dw-edma-v0-debugfs.c create mode 100644 drivers/dma/dw-edma/dw-edma-v0-debugfs.h
drivers/dma/dw-edma/Makefile +2 -1
@@ -1,5 +1,6 @@ # SPDX-License-Identifier: GPL-2.0 obj-$(CONFIG_DW_EDMA) += dw-edma.o +dw-edma-$(CONFIG_DEBUG_FS) := dw-edma-v0-debugfs.o dw-edma-objs := dw-edma-core.o \ - dw-edma-v0-core.o + dw-edma-v0-core.o $(dw-edma-y)
drivers/dma/dw-edma/dw-edma-v0-core.c +2 -0
@@ -345,8 +345,10 @@ int dw_edma_v0_core_device_config(struct dw_edma_chan *chan)/* eDMA debugfs callbacks */ void dw_edma_v0_core_debugfs_on (struct dw_edma_chip *chip) { +dw_edma_v0_debugfs_on (chip); }void dw_edma_v0_core_debugfs_off (void ) { +dw_edma_v0_debugfs_off (); }
drivers/dma/dw-edma/dw-edma-v0-debugfs.c new file +310 -0
310 lines not on this page · raw message
drivers/dma/dw-edma/dw-edma-v0-debugfs.h new file +27 -0
@@ -0,0 +1,27 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* +* Copyright (c) 2018-2019 Synopsys, Inc. and/or its affiliates. +* Synopsys DesignWare eDMA v0 core +* +* Author: Gustavo Pimentel <[email protected]> +*/ + +#ifndef _DW_EDMA_V0_DEBUG_FS_H +#define _DW_EDMA_V0_DEBUG_FS_H + +#include <linux/dma/edma.h> + +#ifdef CONFIG_DEBUG_FS +void dw_edma_v0_debugfs_on (struct dw_edma_chip *chip); +void dw_edma_v0_debugfs_off (void ); +#else +static inline void dw_edma_v0_debugfs_on (struct dw_edma_chip *chip) +{ +} + +static inline void dw_edma_v0_debugfs_off (void ) +{ +} +#endif /* CONFIG_DEBUG_FS */ + +#endif /* _DW_EDMA_V0_DEBUG_FS_H */
Signature · 1 line
2.7.4
PATCH 4/6 PCI: Add Synopsys endpoint EDDA Device ID
In reply to Gustavo PimentelCreate and add Synopsys Endpoint EDDA Device ID to PCI ID list, since this ID is now being use on two different drivers (pci_endpoint_test.ko and dw-edma-pcie.ko).
--- drivers/misc/pci_endpoint_test.c | 2 +- include/linux/pci_ids.h | 1 + 2 files changed, 2 insertions(+), 1 deletion(-)
drivers/misc/pci_endpoint_test.c +1 -1
@@ -789,7 +789,7 @@ static const struct pci_device_id pci_endpoint_test_tbl[] = { { PCI_DEVICE(PCI_VENDOR_ID_TI, PCI_DEVICE_ID_TI_DRA74x) }, { PCI_DEVICE(PCI_VENDOR_ID_TI, PCI_DEVICE_ID_TI_DRA72x) }, { PCI_DEVICE(PCI_VENDOR_ID_FREESCALE, 0x81c0) }, - { PCI_DEVICE(PCI_VENDOR_ID_SYNOPSYS, 0xedda) }, + { PCI_DEVICE_DATA(SYNOPSYS, EDDA, NULL) }, { } };MODULE_DEVICE_TABLE (pci, pci_endpoint_test_tbl);
include/linux/pci_ids.h +1 -0
@@ -2366,6 +2366,7 @@#define PCI_DEVICE_ID_SYNOPSYS_HAPSUSB3 0xabcd#define PCI_DEVICE_ID_SYNOPSYS_HAPSUSB3_AXI 0xabce#define PCI_DEVICE_ID_SYNOPSYS_HAPSUSB31 0xabcf +#define PCI_DEVICE_ID_SYNOPSYS_EDDA 0xedda#define PCI_VENDOR_ID_USR 0x16ec
Signature · 1 line
2.7.4
PATCH 5/6 dmaengine: Add Synopsys eDMA IP PCIe glue-logic
In reply to Gustavo PimentelSynopsys eDMA IP is normally distributed along with Synopsys PCIe EndPoint IP (depends of the use and licensing agreement).
This IP requires some basic configurations, such as:
- eDMA registers BAR
- eDMA registers offset
- eDMA registers size
- eDMA linked list memory BAR
- eDMA linked list memory offset
- eDMA linked list memory size
- eDMA data memory BAR
- eDMA data memory offset
- eDMA data memory size
- eDMA version
- eDMA mode
- IRQs available for eDMA
As a working example, PCIe glue-logic will attach to a Synopsys PCIe EndPoint IP prototype kit (Vendor ID = 0x16c3, Device ID = 0xedda), which has built-in an eDMA IP with this default configuration:
- eDMA registers BAR = 0
- eDMA registers offset = 0x00001000 (4 Kbytes)
- eDMA registers size = 0x00002000 (8 Kbytes)
- eDMA linked list memory BAR = 2
- eDMA linked list memory offset = 0x00000000 (0 Kbytes)
- eDMA linked list memory size = 0x00800000 (8 Mbytes)
- eDMA data memory BAR = 2
- eDMA data memory offset = 0x00800000 (8 Mbytes)
- eDMA data memory size = 0x03800000 (56 Mbytes)
- eDMA version = 0
- eDMA mode = EDMA_MODE_UNROLL
- IRQs = 1
This driver can be compile as built-in or external module in kernel.
To enable this driver just select DW_EDMA_PCIE option in kernel configuration, however it requires and selects automatically DW_EDMA option too.
--- drivers/dma/dw-edma/Kconfig | 9 ++ drivers/dma/dw-edma/Makefile | 1 + drivers/dma/dw-edma/dw-edma-pcie.c | 229 +++++++++++++++++++++++++++++++++++++ 3 files changed, 239 insertions(+) create mode 100644 drivers/dma/dw-edma/dw-edma-pcie.c
drivers/dma/dw-edma/Kconfig +9 -0
@@ -7,3 +7,12 @@ config DW_EDMA help Support the Synopsys DesignWare eDMA controller, normally implemented on endpoints SoCs. + +config DW_EDMA_PCIE + tristate "Synopsys DesignWare eDMA PCIe driver" + depends on PCI && PCI_MSI + select DW_EDMA + help + Provides a glue-logic between the Synopsys DesignWare + eDMA controller and an endpoint PCIe device. This also serves + as a reference design to whom desires to use this IP.
drivers/dma/dw-edma/Makefile +1 -0
@@ -4,3 +4,4 @@ obj-$(CONFIG_DW_EDMA) += dw-edma.o dw-edma-$(CONFIG_DEBUG_FS) := dw-edma-v0-debugfs.o dw-edma-objs := dw-edma-core.o \ dw-edma-v0-core.o $(dw-edma-y) +obj-$(CONFIG_DW_EDMA_PCIE) += dw-edma-pcie.o
drivers/dma/dw-edma/dw-edma-pcie.c new file +229 -0
229 lines not on this page · raw message
Signature · 1 line
2.7.4
PATCH 6/6 MAINTAINERS: Add Synopsys eDMA IP driver maintainer
In reply to Gustavo PimentelAdd Synopsys eDMA IP driver maintainer.
This driver aims to support Synopsys eDMA IP and is normally distributed along with Synopsys PCIe EndPoint IP (depends of the use and licensing agreement).
--- MAINTAINERS | 7 +++++++ 1 file changed, 7 insertions(+)
MAINTAINERS +7 -0
@@ -4513,6 +4513,13 @@ L: [email protected] S: Supported F: drivers/mtd/nand/raw/denali* +DESIGNWARE EDMA CORE IP DRIVER +M: Gustavo Pimentel <[email protected]> +L: [email protected] +S: Maintained +F: drivers/dma/dw-edma/ +F: include/linux/dma/edma.h + DESIGNWARE USB2 DRD IP DRIVER M: Minas Harutyunyan <[email protected]> L: [email protected]
Signature · 1 line
2.7.4