Skip to contentSkip to conversation

Add SD host controller support for SC9860 platform

PATCH Applied Baolin Wang 3 participants 13 messages Jun 4, 2019 – Jul 5, 2019 1 message not in the archive

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

v2 cover Add SD host controller support for SC9860 platform

This patch set adds optional clock support, HS400 enhanced strobe mode support, PHY DLL configuration and other optimization to make the SD host controller can work well on the Spreadtrum SC9860 platform.

Changes from v1:
- Add acked-tags from Adrian.
- Fix one mistake by changing MMC_TIMING_MMC_HS to MMC_TIMING_SD_HS in patch 8.

Baolin Wang (9):
mmc: sdhci-sprd: Check the enable clock's return value correctly
dt-bindings: mmc: sprd: Add another optional clock documentation
mmc: sdhci-sprd: Add optional gate clock support
mmc: sdhci-sprd: Implement the get_max_timeout_count() interface
mmc: sdhci-sprd: Add HS400 enhanced strobe mode
mmc: sdhci-sprd: Enable PHY DLL to make clock stable
dt-bindings: mmc: sprd: Add PHY DLL delay documentation
mmc: sdhci-sprd: Add PHY DLL delay configuration
arm64: dts: sprd: Add Spreadtrum SD host controller support

 .../devicetree/bindings/mmc/sdhci-sprd.txt         |   19 +++
 arch/arm64/boot/dts/sprd/whale2.dtsi               |   35 ++++
 drivers/mmc/host/sdhci-sprd.c                      |  171 +++++++++++++++++++-
 3 files changed, 217 insertions(+), 8 deletions(-)
Signature · 1 line
1.7.9.5
#1 lore raw

PATCH v2 1/9 mmc: sdhci-sprd: Check the enable clock's return value correctly

Missed to check the enable clock's return value, fix it.

---
 drivers/mmc/host/sdhci-sprd.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/mmc/host/sdhci-sprd.c +1 -1
index 9a822e2..e741491 100644
@@ -368,7 +368,7 @@ static int sdhci_sprd_probe(struct platform_device *pdev)
 	if (ret)
 		goto pltfm_free;
 
-	clk_prepare_enable(sprd_host->clk_enable);
+	ret = clk_prepare_enable(sprd_host->clk_enable);
 	if (ret)
 		goto clk_disable;
 
Signature · 1 line
1.7.9.5
#2 lore raw

PATCH v2 2/9 dt-bindings: mmc: sprd: Add another optional clock documentation

In reply to Baolin Wang

For some Spreadtrum platforms like SC9860 platform, we should enable another gate clock '2x_enable' to make the SD host controller work well. Thus add documentation for this optional clock.

---
 .../devicetree/bindings/mmc/sdhci-sprd.txt         |    1 +
 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/mmc/sdhci-sprd.txt +1 -0
index 45c9978..a285c77 100644
@@ -14,6 +14,7 @@ Required properties:
 - clock-names: Should contain the following:
 	"sdio" - SDIO source clock (required)
 	"enable" - gate clock which used for enabling/disabling the device (required)
+	"2x_enable" - gate clock controlling the device for some special platforms (optional)
 
 Optional properties:
 - assigned-clocks: the same with "sdio" clock
Signature · 1 line
1.7.9.5
#3 lore raw

PATCH v2 3/9 mmc: sdhci-sprd: Add optional gate clock support

In reply to Baolin Wang

For the Spreadtrum SC9860 platform, we should enable another gate clock '2x_enable' to make the SD host controller work well.

---
 drivers/mmc/host/sdhci-sprd.c |   35 +++++++++++++++++++++++++++++------
 1 file changed, 29 insertions(+), 6 deletions(-)
drivers/mmc/host/sdhci-sprd.c +29 -6
index e741491..31ba7d6 100644
@@ -60,6 +60,7 @@ struct sdhci_sprd_host {
 	u32 version;
 	struct clk *clk_sdio;
 	struct clk *clk_enable;
+	struct clk *clk_2x_enable;
 	u32 base_rate;
 	int flags; /* backup of host attribute */
 };
@@ -364,6 +365,10 @@ static int sdhci_sprd_probe(struct platform_device *pdev)
 	}
 	sprd_host->clk_enable = clk;
 
+	clk = devm_clk_get(&pdev->dev, "2x_enable");
+	if (!IS_ERR(clk))
+		sprd_host->clk_2x_enable = clk;
+
 	ret = clk_prepare_enable(sprd_host->clk_sdio);
 	if (ret)
 		goto pltfm_free;
@@ -372,6 +377,10 @@ static int sdhci_sprd_probe(struct platform_device *pdev)
 	if (ret)
 		goto clk_disable;
 
+	ret = clk_prepare_enable(sprd_host->clk_2x_enable);
+	if (ret)
+		goto clk_disable2;
+
 	sdhci_sprd_init_config(host);
 	host->version = sdhci_readw(host, SDHCI_HOST_VERSION);
 	sprd_host->version = ((host->version & SDHCI_VENDOR_VER_MASK) >>
@@ -408,6 +417,9 @@ static int sdhci_sprd_probe(struct platform_device *pdev)
 	pm_runtime_disable(&pdev->dev);
 	pm_runtime_set_suspended(&pdev->dev);
 
+	clk_disable_unprepare(sprd_host->clk_2x_enable);
+
+clk_disable2:
 	clk_disable_unprepare(sprd_host->clk_enable);
 
 clk_disable:
@@ -427,6 +439,7 @@ static int sdhci_sprd_remove(struct platform_device *pdev)
 	mmc_remove_host(mmc);
 	clk_disable_unprepare(sprd_host->clk_sdio);
 	clk_disable_unprepare(sprd_host->clk_enable);
+	clk_disable_unprepare(sprd_host->clk_2x_enable);
 
 	mmc_free_host(mmc);
 
@@ -449,6 +462,7 @@ static int sdhci_sprd_runtime_suspend(struct device *dev)
 
 	clk_disable_unprepare(sprd_host->clk_sdio);
 	clk_disable_unprepare(sprd_host->clk_enable);
+	clk_disable_unprepare(sprd_host->clk_2x_enable);
 
 	return 0;
 }
@@ -459,19 +473,28 @@ static int sdhci_sprd_runtime_resume(struct device *dev)
 	struct sdhci_sprd_host *sprd_host = TO_SPRD_HOST(host);
 	int ret;
 
-	ret = clk_prepare_enable(sprd_host->clk_enable);
+	ret = clk_prepare_enable(sprd_host->clk_2x_enable);
 	if (ret)
 		return ret;
 
+	ret = clk_prepare_enable(sprd_host->clk_enable);
+	if (ret)
+		goto clk_2x_disable;
+
 	ret = clk_prepare_enable(sprd_host->clk_sdio);
-	if (ret) {
-		clk_disable_unprepare(sprd_host->clk_enable);
-		return ret;
-	}
+	if (ret)
+		goto clk_disable;
 
 	sdhci_runtime_resume_host(host);
-
 	return 0;
+
+clk_disable:
+	clk_disable_unprepare(sprd_host->clk_enable);
+
+clk_2x_disable:
+	clk_disable_unprepare(sprd_host->clk_2x_enable);
+
+	return ret;
 }
 #endif
 
Signature · 1 line
1.7.9.5
#4 lore raw

PATCH v2 4/9 mmc: sdhci-sprd: Implement the get_max_timeout_count() interface

In reply to Baolin Wang

Implement the get_max_timeout_count() interface to set the Spredtrum SD host controller actual maximum timeout count.

---
 drivers/mmc/host/sdhci-sprd.c |    7 +++++++
 1 file changed, 7 insertions(+)
drivers/mmc/host/sdhci-sprd.c +7 -0
index 31ba7d6..d91281d 100644
@@ -285,6 +285,12 @@ static void sdhci_sprd_hw_reset(struct sdhci_host *host)
 	usleep_range(300, 500);
 }
 
+static unsigned int sdhci_sprd_get_max_timeout_count(struct sdhci_host *host)
+{
+	/* The Spredtrum controller actual maximum timeout count is 1 << 31 */
+	return 1 << 31;
+}
+
 static struct sdhci_ops sdhci_sprd_ops = {
 	.read_l = sdhci_sprd_readl,
 	.write_l = sdhci_sprd_writel,
@@ -296,6 +302,7 @@ static void sdhci_sprd_hw_reset(struct sdhci_host *host)
 	.reset = sdhci_reset,
 	.set_uhs_signaling = sdhci_sprd_set_uhs_signaling,
 	.hw_reset = sdhci_sprd_hw_reset,
+	.get_max_timeout_count = sdhci_sprd_get_max_timeout_count,
 };
 
 static void sdhci_sprd_request(struct mmc_host *mmc, struct mmc_request *mrq)
Signature · 1 line
1.7.9.5
#5 lore raw

PATCH v2 5/9 mmc: sdhci-sprd: Add HS400 enhanced strobe mode

In reply to Baolin Wang

Add HS400 enhanced strobe mode support for Spreadtrum SD host controller.

---
 drivers/mmc/host/sdhci-sprd.c |   32 ++++++++++++++++++++++++++++++++
 1 file changed, 32 insertions(+)
drivers/mmc/host/sdhci-sprd.c +32 -0
index d91281d..edec197 100644
@@ -41,6 +41,7 @@
 /* SDHCI_HOST_CONTROL2 */
 #define  SDHCI_SPRD_CTRL_HS200		0x0005
 #define  SDHCI_SPRD_CTRL_HS400		0x0006
+#define  SDHCI_SPRD_CTRL_HS400ES	0x0007
 
 /*
  * According to the standard specification, BIT(3) of SDHCI_SOFTWARE_RESET is
@@ -132,6 +133,15 @@ static inline void sdhci_sprd_sd_clk_off(struct sdhci_host *host)
 	sdhci_writew(host, ctrl, SDHCI_CLOCK_CONTROL);
 }
 
+static inline void sdhci_sprd_sd_clk_on(struct sdhci_host *host)
+{
+	u16 ctrl;
+
+	ctrl = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
+	ctrl |= SDHCI_CLOCK_CARD_EN;
+	sdhci_writew(host, ctrl, SDHCI_CLOCK_CONTROL);
+}
+
 static inline void
 sdhci_sprd_set_dll_invert(struct sdhci_host *host, u32 mask, bool en)
 {
@@ -325,6 +335,26 @@ static void sdhci_sprd_request(struct mmc_host *mmc, struct mmc_request *mrq)
 	sdhci_request(mmc, mrq);
 }
 
+static void sdhci_sprd_hs400_enhanced_strobe(struct mmc_host *mmc,
+					     struct mmc_ios *ios)
+{
+	struct sdhci_host *host = mmc_priv(mmc);
+	u16 ctrl_2;
+
+	if (!ios->enhanced_strobe)
+		return;
+
+	sdhci_sprd_sd_clk_off(host);
+
+	/* Set HS400 enhanced strobe mode */
+	ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
+	ctrl_2 &= ~SDHCI_CTRL_UHS_MASK;
+	ctrl_2 |= SDHCI_SPRD_CTRL_HS400ES;
+	sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
+
+	sdhci_sprd_sd_clk_on(host);
+}
+
 static const struct sdhci_pltfm_data sdhci_sprd_pdata = {
 	.quirks = SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK,
 	.quirks2 = SDHCI_QUIRK2_BROKEN_HS200 |
@@ -346,6 +376,8 @@ static int sdhci_sprd_probe(struct platform_device *pdev)
 	host->dma_mask = DMA_BIT_MASK(64);
 	pdev->dev.dma_mask = &host->dma_mask;
 	host->mmc_host_ops.request = sdhci_sprd_request;
+	host->mmc_host_ops.hs400_enhanced_strobe =
+		sdhci_sprd_hs400_enhanced_strobe;
 
 	host->mmc->caps = MMC_CAP_SD_HIGHSPEED | MMC_CAP_MMC_HIGHSPEED |
 		MMC_CAP_ERASE | MMC_CAP_CMD23;
Signature · 1 line
1.7.9.5
#6 lore raw

PATCH v2 6/9 mmc: sdhci-sprd: Enable PHY DLL to make clock stable

In reply to Baolin Wang

For the Spreadtrum SD host controller, when we changed the clock to be more than 52M, we should enable the PHY DLL which is used to track the clock frequency to make the clock work more stable. Otherwise deviation may occur of the higher clock.

---
 drivers/mmc/host/sdhci-sprd.c |   44 ++++++++++++++++++++++++++++++++++++++++-
 1 file changed, 43 insertions(+), 1 deletion(-)
drivers/mmc/host/sdhci-sprd.c +43 -1
index edec197..e6eda13 100644
@@ -22,6 +22,13 @@
 /* SDHCI_ARGUMENT2 register high 16bit */
 #define SDHCI_SPRD_ARG2_STUFF		GENMASK(31, 16)
 
+#define SDHCI_SPRD_REG_32_DLL_CFG	0x200
+#define  SDHCI_SPRD_DLL_ALL_CPST_EN	(BIT(18) | BIT(24) | BIT(25) | BIT(26) | BIT(27))
+#define  SDHCI_SPRD_DLL_EN		BIT(21)
+#define  SDHCI_SPRD_DLL_SEARCH_MODE	BIT(16)
+#define  SDHCI_SPRD_DLL_INIT_COUNT	0xc00
+#define  SDHCI_SPRD_DLL_PHASE_INTERNAL	0x3
+
 #define SDHCI_SPRD_REG_32_DLL_DLY_OFFSET	0x208
 #define  SDHCIBSPRD_IT_WR_DLY_INV		BIT(5)
 #define  SDHCI_SPRD_BIT_CMD_DLY_INV		BIT(13)
@@ -56,6 +63,7 @@
 #define SDHCI_SPRD_CLK_MAX_DIV		1023
 
 #define SDHCI_SPRD_CLK_DEF_RATE		26000000
+#define SDHCI_SPRD_PHY_DLL_CLK		52000000
 
 struct sdhci_sprd_host {
 	u32 version;
@@ -200,9 +208,33 @@ static inline void _sdhci_sprd_set_clock(struct sdhci_host *host,
 	}
 }
 
+static void sdhci_sprd_enable_phy_dll(struct sdhci_host *host)
+{
+	u32 tmp;
+
+	tmp = sdhci_readl(host, SDHCI_SPRD_REG_32_DLL_CFG);
+	tmp &= ~(SDHCI_SPRD_DLL_EN | SDHCI_SPRD_DLL_ALL_CPST_EN);
+	sdhci_writel(host, tmp, SDHCI_SPRD_REG_32_DLL_CFG);
+	/* wait 1ms */
+	usleep_range(1000, 1250);
+
+	tmp = sdhci_readl(host, SDHCI_SPRD_REG_32_DLL_CFG);
+	tmp |= SDHCI_SPRD_DLL_ALL_CPST_EN | SDHCI_SPRD_DLL_SEARCH_MODE |
+		SDHCI_SPRD_DLL_INIT_COUNT | SDHCI_SPRD_DLL_PHASE_INTERNAL;
+	sdhci_writel(host, tmp, SDHCI_SPRD_REG_32_DLL_CFG);
+	/* wait 1ms */
+	usleep_range(1000, 1250);
+
+	tmp = sdhci_readl(host, SDHCI_SPRD_REG_32_DLL_CFG);
+	tmp |= SDHCI_SPRD_DLL_EN;
+	sdhci_writel(host, tmp, SDHCI_SPRD_REG_32_DLL_CFG);
+	/* wait 1ms */
+	usleep_range(1000, 1250);
+}
+
 static void sdhci_sprd_set_clock(struct sdhci_host *host, unsigned int clock)
 {
-	bool en = false;
+	bool en = false, clk_changed = false;
 
 	if (clock == 0) {
 		sdhci_writew(host, 0, SDHCI_CLOCK_CONTROL);
@@ -214,9 +246,19 @@ static void sdhci_sprd_set_clock(struct sdhci_host *host, unsigned int clock)
 			en = true;
 		sdhci_sprd_set_dll_invert(host, SDHCI_SPRD_BIT_CMD_DLY_INV |
 					  SDHCI_SPRD_BIT_POSRD_DLY_INV, en);
+		clk_changed = true;
 	} else {
 		_sdhci_sprd_set_clock(host, clock);
 	}
+
+	/*
+	 * According to the Spreadtrum SD host specification, when we changed
+	 * the clock to be more than 52M, we should enable the PHY DLL which
+	 * is used to track the clock frequency to make the clock work more
+	 * stable. Otherwise deviation may occur of the higher clock.
+	 */
+	if (clk_changed && clock > SDHCI_SPRD_PHY_DLL_CLK)
+		sdhci_sprd_enable_phy_dll(host);
 }
 
 static unsigned int sdhci_sprd_get_max_clock(struct sdhci_host *host)
Signature · 1 line
1.7.9.5
#7 lore raw

PATCH v2 7/9 dt-bindings: mmc: sprd: Add PHY DLL delay documentation

In reply to Baolin Wang

Introduce some PHY DLL delays properties to help to sample the PHY clock.

---
 .../devicetree/bindings/mmc/sdhci-sprd.txt         |   18 ++++++++++++++++++
 1 file changed, 18 insertions(+)
Documentation/devicetree/bindings/mmc/sdhci-sprd.txt +18 -0
index a285c77..e675397 100644
@@ -20,6 +20,23 @@ Optional properties:
 - assigned-clocks: the same with "sdio" clock
 - assigned-clock-parents: the default parent of "sdio" clock
 
+PHY DLL delays are used to delay the data valid window, and align the window
+to sampling clock. PHY DLL delays can be configured by following properties,
+and each property contains 4 cells which are used to configure the clock data
+write line delay value, clock read command line delay value, clock read data
+positive edge delay value and clock read data negative edge delay value.
+Each cell's delay value unit is cycle of the PHY clock.
+
+- sprd,phy-delay-legacy: Delay value for legacy timing.
+- sprd,phy-delay-sd-highspeed: Delay value for SD high-speed timing.
+- sprd,phy-delay-sd-uhs-sdr50: Delay value for SD UHS SDR50 timing.
+- sprd,phy-delay-sd-uhs-sdr104: Delay value for SD UHS SDR50 timing.
+- sprd,phy-delay-mmc-highspeed: Delay value for MMC high-speed timing.
+- sprd,phy-delay-mmc-ddr52: Delay value for MMC DDR52 timing.
+- sprd,phy-delay-mmc-hs200: Delay value for MMC HS200 timing.
+- sprd,phy-delay-mmc-hs400: Delay value for MMC HS400 timing.
+- sprd,phy-delay-mmc-hs400es: Delay value for MMC HS400 enhanced strobe timing.
+
 Examples:
 
 sdio0: sdio@20600000 {
@@ -33,6 +50,7 @@ sdio0: sdio@20600000 {
 	assigned-clocks = <&ap_clk CLK_EMMC_2X>;
 	assigned-clock-parents = <&rpll CLK_RPLL_390M>;
 
+	sprd,phy-delay-sd-uhs-sdr104 = <0x3f 0x7f 0x2e 0x2e>;
 	bus-width = <8>;
 	non-removable;
 	no-sdio;
Signature · 1 line
1.7.9.5
#8 lore raw

PATCH v2 8/9 mmc: sdhci-sprd: Add PHY DLL delay configuration

In reply to Baolin Wang

Set the PHY DLL delay for each timing mode, which is used to sample the clock accurately and make the clock more stable.

---
 drivers/mmc/host/sdhci-sprd.c |   51 +++++++++++++++++++++++++++++++++++++++++
 1 file changed, 51 insertions(+)
drivers/mmc/host/sdhci-sprd.c +51 -0
index e6eda13..024c3c5 100644
@@ -29,6 +29,8 @@
 #define  SDHCI_SPRD_DLL_INIT_COUNT	0xc00
 #define  SDHCI_SPRD_DLL_PHASE_INTERNAL	0x3
 
+#define SDHCI_SPRD_REG_32_DLL_DLY	0x204
+
 #define SDHCI_SPRD_REG_32_DLL_DLY_OFFSET	0x208
 #define  SDHCIBSPRD_IT_WR_DLY_INV		BIT(5)
 #define  SDHCI_SPRD_BIT_CMD_DLY_INV		BIT(13)
@@ -72,6 +74,24 @@ struct sdhci_sprd_host {
 	struct clk *clk_2x_enable;
 	u32 base_rate;
 	int flags; /* backup of host attribute */
+	u32 phy_delay[MMC_TIMING_MMC_HS400 + 2];
+};
+
+struct sdhci_sprd_phy_cfg {
+	const char *property;
+	u8 timing;
+};
+
+static const struct sdhci_sprd_phy_cfg sdhci_sprd_phy_cfgs[] = {
+	{ "sprd,phy-delay-legacy", MMC_TIMING_LEGACY, },
+	{ "sprd,phy-delay-sd-highspeed", MMC_TIMING_SD_HS, },
+	{ "sprd,phy-delay-sd-uhs-sdr50", MMC_TIMING_UHS_SDR50, },
+	{ "sprd,phy-delay-sd-uhs-sdr104", MMC_TIMING_UHS_SDR104, },
+	{ "sprd,phy-delay-mmc-highspeed", MMC_TIMING_MMC_HS, },
+	{ "sprd,phy-delay-mmc-ddr52", MMC_TIMING_MMC_DDR52, },
+	{ "sprd,phy-delay-mmc-hs200", MMC_TIMING_MMC_HS200, },
+	{ "sprd,phy-delay-mmc-hs400", MMC_TIMING_MMC_HS400, },
+	{ "sprd,phy-delay-mmc-hs400es", MMC_TIMING_MMC_HS400 + 1, },
 };
 
 #define TO_SPRD_HOST(host) sdhci_pltfm_priv(sdhci_priv(host))
@@ -276,6 +296,9 @@ static unsigned int sdhci_sprd_get_min_clock(struct sdhci_host *host)
 static void sdhci_sprd_set_uhs_signaling(struct sdhci_host *host,
 					 unsigned int timing)
 {
+	struct sdhci_sprd_host *sprd_host = TO_SPRD_HOST(host);
+	struct mmc_host *mmc = host->mmc;
+	u32 *p = sprd_host->phy_delay;
 	u16 ctrl_2;
 
 	if (timing == host->timing)
@@ -314,6 +337,9 @@ static void sdhci_sprd_set_uhs_signaling(struct sdhci_host *host,
 	}
 
 	sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
+
+	if (!mmc->ios.enhanced_strobe)
+		sdhci_writel(host, p[timing], SDHCI_SPRD_REG_32_DLL_DLY);
 }
 
 static void sdhci_sprd_hw_reset(struct sdhci_host *host)
@@ -381,6 +407,8 @@ static void sdhci_sprd_hs400_enhanced_strobe(struct mmc_host *mmc,
 					     struct mmc_ios *ios)
 {
 	struct sdhci_host *host = mmc_priv(mmc);
+	struct sdhci_sprd_host *sprd_host = TO_SPRD_HOST(host);
+	u32 *p = sprd_host->phy_delay;
 	u16 ctrl_2;
 
 	if (!ios->enhanced_strobe)
@@ -395,6 +423,28 @@ static void sdhci_sprd_hs400_enhanced_strobe(struct mmc_host *mmc,
 	sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
 
 	sdhci_sprd_sd_clk_on(host);
+
+	/* Set the PHY DLL delay value for HS400 enhanced strobe mode */
+	sdhci_writel(host, p[MMC_TIMING_MMC_HS400 + 1],
+		     SDHCI_SPRD_REG_32_DLL_DLY);
+}
+
+static void sdhci_sprd_phy_param_parse(struct sdhci_sprd_host *sprd_host,
+				       struct device_node *np)
+{
+	u32 *p = sprd_host->phy_delay;
+	int ret, i, index;
+	u32 val[4];
+
+	for (i = 0; i < ARRAY_SIZE(sdhci_sprd_phy_cfgs); i++) {
+		ret = of_property_read_u32_array(np,
+				sdhci_sprd_phy_cfgs[i].property, val, 4);
+		if (ret)
+			continue;
+
+		index = sdhci_sprd_phy_cfgs[i].timing;
+		p[index] = val[0] | (val[1] << 8) | (val[2] << 16) | (val[3] << 24);
+	}
 }
 
 static const struct sdhci_pltfm_data sdhci_sprd_pdata = {
@@ -428,6 +478,7 @@ static int sdhci_sprd_probe(struct platform_device *pdev)
 		goto pltfm_free;
 
 	sprd_host = TO_SPRD_HOST(host);
+	sdhci_sprd_phy_param_parse(sprd_host, pdev->dev.of_node);
 
 	clk = devm_clk_get(&pdev->dev, "sdio");
 	if (IS_ERR(clk)) {
Signature · 1 line
1.7.9.5
#9 lore raw

PATCH v2 9/9 arm64: dts: sprd: Add Spreadtrum SD host controller support

In reply to Baolin Wang

Add one Spreadtrum SD host controller to support eMMC card for Spreadtrum SC9860 platform.

---
 arch/arm64/boot/dts/sprd/whale2.dtsi |   35 ++++++++++++++++++++++++++++++++++
 1 file changed, 35 insertions(+)
arch/arm64/boot/dts/sprd/whale2.dtsi +35 -0
index 4bb862c..79b9591c 100644
@@ -130,6 +130,34 @@
 				clock-names = "enable";
 				clocks = <&apahb_gate CLK_DMA_EB>;
 			};
+
+			sdio3: sdio@50430000 {
+				compatible  = "sprd,sdhci-r11";
+				reg = <0 0x50430000 0 0x1000>;
+				interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+
+				clock-names = "sdio", "enable", "2x_enable";
+				clocks = <&aon_prediv CLK_EMMC_2X>,
+				       <&apahb_gate CLK_EMMC_EB>,
+				       <&aon_gate CLK_EMMC_2X_EN>;
+				assigned-clocks = <&aon_prediv CLK_EMMC_2X>;
+				assigned-clock-parents = <&clk_l0_409m6>;
+
+				sprd,phy-delay-mmc-hs400 = <0x44 0x7f 0x2e 0x2e>;
+				sprd,phy-delay-mmc-hs200 = <0x0 0x8c 0x8c 0x8c>;
+				sprd,phy-delay-mmc-ddr52 = <0x3f 0x75 0x14 0x14>;
+				sprd,phy-delay-mmc-hs400es = <0x3f 0x3f 0x2e 0x2e>;
+				vmmc-supply = <&vddemmccore>;
+				bus-width = <8>;
+				non-removable;
+				no-sdio;
+				no-sd;
+				cap-mmc-hw-reset;
+				mmc-hs400-enhanced-strobe;
+				mmc-hs400-1_8v;
+				mmc-hs200-1_8v;
+				mmc-ddr-1_8v;
+			};
 		};
 
 		aon {
@@ -272,4 +300,11 @@
 		clock-frequency = <100000000>;
 		clock-output-names = "ext-rco-100m";
 	};
+
+	clk_l0_409m6: clk_l0_409m6 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <409600000>;
+		clock-output-names = "ext-409m6";
+	};
 };
Signature · 1 line
1.7.9.5
#10 lore raw

Re: [PATCH v2 9/9] arm64: dts: sprd: Add Spreadtrum SD host controller support

Quoted 4 lines · Baolin Wang

Add one Spreadtrum SD host controller to support eMMC card for Spreadtrum SC9860 platform.

Applied, thanks!

-Olof

#11 lore raw
In reply to Baolin Wang
Quoted 20 lines · Baolin Wang

This patch set adds optional clock support, HS400 enhanced strobe mode support, PHY DLL configuration and other optimization to make the SD host controller can work well on the Spreadtrum SC9860 platform.

Changes from v1:
- Add acked-tags from Adrian.
- Fix one mistake by changing MMC_TIMING_MMC_HS to MMC_TIMING_SD_HS in patch 8.

Baolin Wang (9):
mmc: sdhci-sprd: Check the enable clock's return value correctly
dt-bindings: mmc: sprd: Add another optional clock documentation
mmc: sdhci-sprd: Add optional gate clock support
mmc: sdhci-sprd: Implement the get_max_timeout_count() interface
mmc: sdhci-sprd: Add HS400 enhanced strobe mode
mmc: sdhci-sprd: Enable PHY DLL to make clock stable
dt-bindings: mmc: sprd: Add PHY DLL delay documentation
mmc: sdhci-sprd: Add PHY DLL delay configuration
arm64: dts: sprd: Add Spreadtrum SD host controller support

Quoted 8 lines
 .../devicetree/bindings/mmc/sdhci-sprd.txt         |   19 +++
 arch/arm64/boot/dts/sprd/whale2.dtsi               |   35 ++++
 drivers/mmc/host/sdhci-sprd.c                      |  171 +++++++++++++++++++-
 3 files changed, 217 insertions(+), 8 deletions(-)

--
1.7.9.5

Patch 1 -> patch 8, applied for next, thanks!

Patch 9 is for arm-soc.

Kind regards
Uffe

A message that is not in the archive (sent off-list or not yet received): [email protected]

#13 lore raw

Re: [PATCH v2 1/9] mmc: sdhci-sprd: Check the enable clock's return value correctly

On Fri, Jul 5, 2019 at 3:25 PM Olof Johansson via Linux.Kernel.Org <[email protected]> wrote:

Hmm, well, that didn't work like I expected to. Sorry for the noise.

-Olof