drm: bridge: Add NWL MIPI DSI host controller support

The Northwest Logic MIPI DSI IP core can be found in NXPs i.MX8 SoCs.

Signed-off-by Guido Günther <[email protected]>

Tested-by Robert Chiras <[email protected]>

Reviewed-by Rob Herring <[email protected]>

---
 .../bindings/display/bridge/nwl-dsi.yaml      | 176 ++++++++++++++++++
 1 file changed, 176 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/bridge/nwl-dsi.yaml

Documentation/devicetree/bindings/display/bridge/nwl-dsi.yaml new file +111 -0

new file mode 100644
index 000000000000..31119c7885ff
@@ -0,0 +1,176 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: https://protect2.fireeye.com/url?k=7c9397fbdbbe3fd5.7c921cb4-87fc4542b5f41502&u=http://devicetree.org/schemas/display/bridge/nwl-dsi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Northwest Logic MIPI-DSI controller on i.MX SoCs
+
+maintainers:
+  - Guido Gúnther <[email protected]>
+  - Robert Chiras <[email protected]>
+
+description: |
+  NWL MIPI-DSI host controller found on i.MX8 platforms. This is a dsi bridge for
+  the SOCs NWL MIPI-DSI host controller.
+
+properties:
+  compatible:
+    const: fsl,imx8mq-nwl-dsi
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  '#address-cells':
+    const: 1
+
+  '#size-cells':
+    const: 0
+
+  clocks:
+    items:
+      - description: DSI core clock
+      - description: RX_ESC clock (used in escape mode)
+      - description: TX_ESC clock (used in escape mode)
+      - description: PHY_REF clock
+
+  clock-names:
+    items:
+      - const: core
+      - const: rx_esc
+      - const: tx_esc
+      - const: phy_ref
+
+  mux-controls:
+    description:
+      mux controller node to use for operating the input mux
+
+  phys:
+    maxItems: 1
+    description:
+      A phandle to the phy module representing the DPHY
+
+  phy-names:
+    items:
+      - const: dphy
+
+  power-domains:
+    maxItems: 1
+
+  resets:
+    items:
+      - description: dsi byte reset line
+      - description: dsi dpi reset line
+      - description: dsi esc reset line
+      - description: dsi pclk reset line
+
+  reset-names:
+    items:
+      - const: byte
+      - const: dpi
+      - const: esc
+      - const: pclk
+
+  ports:
+    type: object
+    description:
+      A node containing DSI input & output port nodes with endpoint
+      definitions as documented in
+      Documentation/devicetree/bindings/graph.txt.
+    properties:
+      port@0:
+        type: object
+        description:
+          Input port node to receive pixel data from the
+          display controller
+
+      port@1:
+        type: object
+        description:
+          DSI output port node to the panel or the next bridge
+          in the chain
+
+      '#address-cells':
+        const: 1
+
+      '#size-cells':
+        const: 0
+
+    required:
+      - '#address-cells'
+      - '#size-cells'
+      - port@0
+      - port@1
+
+    additionalProperties: false
+
+patternProperties:
+  "^panel@[0-9]+$":

Documentation/devicetree/bindings/display/bridge/nwl-dsi.yaml new file +55 -0

+  - phy-names
+  - phys
+  - ports
+  - reg
+  - reset-names
+  - resets
+
+additionalProperties: false
+
+examples:
+ - |
+
+   mipi_dsi: mipi_dsi@30a00000 {
+              #address-cells = <1>;
+              #size-cells = <0>;
+              compatible = "fsl,imx8mq-nwl-dsi";
+              reg = <0x30A00000 0x300>;
+              clocks = <&clk 163>, <&clk 244>, <&clk 245>, <&clk 164>;
+              clock-names = "core", "rx_esc", "tx_esc", "phy_ref";
+              interrupts = <0 34 4>;
+              mux-controls = <&mux 0>;
+              power-domains = <&pgc_mipi>;
+              resets = <&src 0>, <&src 1>, <&src 2>, <&src 3>;
+              reset-names = "byte", "dpi", "esc", "pclk";
+              phys = <&dphy>;
+              phy-names = "dphy";
+
+              panel@0 {
+                      compatible = "rocktech,jh057n00900";
+                      reg = <0>;
+                      port@0 {
+                           panel_in: endpoint {
+                                     remote-endpoint = <&mipi_dsi_out>;
+                           };
+                      };
+              };
+
+              ports {
+                    #address-cells = <1>;
+                    #size-cells = <0>;
+
+                    port@0 {
+                           reg = <0>;
+                           mipi_dsi_in: endpoint {
+                                        remote-endpoint = <&lcdif_mipi_dsi>;
+                           };
+                    };
+                    port@1 {
+                           reg = <1>;
+                           mipi_dsi_out: endpoint {
+                                         remote-endpoint = <&panel_in>;
+                           };
+                    };
+              };
+      };

Quoted 133 lines · Guido Günther

The Northwest Logic MIPI DSI IP core can be found in NXPs i.MX8 SoCs.

Signed-off-by Guido Günther <[email protected]>

Tested-by Robert Chiras <[email protected]>

Reviewed-by Rob Herring <[email protected]>

---
 .../bindings/display/bridge/nwl-dsi.yaml      | 176 ++++++++++++++++++
 1 file changed, 176 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/bridge/nwl-dsi.yaml

Documentation/devicetree/bindings/display/bridge/nwl-dsi.yaml new file +117 -0

new file mode 100644
index 000000000000..31119c7885ff
@@ -0,0 +1,176 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: https://protect2.fireeye.com/url?k=7c9397fbdbbe3fd5.7c921cb4-87fc4542b5f41502&u=http://devicetree.org/schemas/display/bridge/nwl-dsi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Northwest Logic MIPI-DSI controller on i.MX SoCs
+
+maintainers:
+  - Guido Gúnther <[email protected]>
+  - Robert Chiras <[email protected]>
+
+description: |
+  NWL MIPI-DSI host controller found on i.MX8 platforms. This is a dsi bridge for
+  the SOCs NWL MIPI-DSI host controller.
+
+properties:
+  compatible:
+    const: fsl,imx8mq-nwl-dsi
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  '#address-cells':
+    const: 1
+
+  '#size-cells':
+    const: 0
+
+  clocks:
+    items:
+      - description: DSI core clock
+      - description: RX_ESC clock (used in escape mode)
+      - description: TX_ESC clock (used in escape mode)
+      - description: PHY_REF clock
+
+  clock-names:
+    items:
+      - const: core
+      - const: rx_esc
+      - const: tx_esc
+      - const: phy_ref
+
+  mux-controls:
+    description:
+      mux controller node to use for operating the input mux
+
+  phys:
+    maxItems: 1
+    description:
+      A phandle to the phy module representing the DPHY
+
+  phy-names:
+    items:
+      - const: dphy
+
+  power-domains:
+    maxItems: 1
+
+  resets:
+    items:
+      - description: dsi byte reset line
+      - description: dsi dpi reset line
+      - description: dsi esc reset line
+      - description: dsi pclk reset line
+
+  reset-names:
+    items:
+      - const: byte
+      - const: dpi
+      - const: esc
+      - const: pclk
+
+  ports:
+    type: object
+    description:
+      A node containing DSI input & output port nodes with endpoint
+      definitions as documented in
+      Documentation/devicetree/bindings/graph.txt.
+    properties:
+      port@0:
+        type: object
+        description:
+          Input port node to receive pixel data from the
+          display controller
+
+      port@1:
+        type: object
+        description:
+          DSI output port node to the panel or the next bridge
+          in the chain
+
+      '#address-cells':
+        const: 1
+
+      '#size-cells':
+        const: 0
+
+    required:
+      - '#address-cells'
+      - '#size-cells'
+      - port@0
+      - port@1
+
+    additionalProperties: false
+
+patternProperties:
+  "^panel@[0-9]+$":
+    type: object
+
+required:
+  - '#address-cells'
+  - '#size-cells'
+  - clock-names

Documentation/devicetree/bindings/display/bridge/nwl-dsi.yaml line 121

Quoted 4 lines

Documentation/devicetree/bindings/display/bridge/nwl-dsi.yaml new file +4 -0

+  - clocks
+  - compatible
+  - interrupts
+  - mux-controls

As I understand mux is not a part of the device, so maybe would be safer to make it optional.

Regards

Andrzej

Quoted 55 lines

Documentation/devicetree/bindings/display/bridge/nwl-dsi.yaml new file +55 -0

+  - phy-names
+  - phys
+  - ports
+  - reg
+  - reset-names
+  - resets
+
+additionalProperties: false
+
+examples:
+ - |
+
+   mipi_dsi: mipi_dsi@30a00000 {
+              #address-cells = <1>;
+              #size-cells = <0>;
+              compatible = "fsl,imx8mq-nwl-dsi";
+              reg = <0x30A00000 0x300>;
+              clocks = <&clk 163>, <&clk 244>, <&clk 245>, <&clk 164>;
+              clock-names = "core", "rx_esc", "tx_esc", "phy_ref";
+              interrupts = <0 34 4>;
+              mux-controls = <&mux 0>;
+              power-domains = <&pgc_mipi>;
+              resets = <&src 0>, <&src 1>, <&src 2>, <&src 3>;
+              reset-names = "byte", "dpi", "esc", "pclk";
+              phys = <&dphy>;
+              phy-names = "dphy";
+
+              panel@0 {
+                      compatible = "rocktech,jh057n00900";
+                      reg = <0>;
+                      port@0 {
+                           panel_in: endpoint {
+                                     remote-endpoint = <&mipi_dsi_out>;
+                           };
+                      };
+              };
+
+              ports {
+                    #address-cells = <1>;
+                    #size-cells = <0>;
+
+                    port@0 {
+                           reg = <0>;
+                           mipi_dsi_in: endpoint {
+                                        remote-endpoint = <&lcdif_mipi_dsi>;
+                           };
+                    };
+                    port@1 {
+                           reg = <1>;
+                           mipi_dsi_out: endpoint {
+                                         remote-endpoint = <&panel_in>;
+                           };
+                    };
+              };
+      };

This adds initial support for the NWL MIPI DSI Host controller found on i.MX8 SoCs.

It adds support for the i.MX8MQ but the same IP can be found on e.g. the i.MX8QXP.

It has been tested on the Librem 5 devkit using mxsfb.

Signed-off-by Guido Günther <[email protected]>

Co-developed-by Robert Chiras <[email protected]>

Signed-off-by Robert Chiras <[email protected]>

Tested-by Robert Chiras <[email protected]>

---
 drivers/gpu/drm/bridge/Kconfig   |   16 +
 drivers/gpu/drm/bridge/Makefile  |    3 +
 drivers/gpu/drm/bridge/nwl-dsi.c | 1180 ++++++++++++++++++++++++++++++
 drivers/gpu/drm/bridge/nwl-dsi.h |  144 ++++
 4 files changed, 1343 insertions(+)
 create mode 100644 drivers/gpu/drm/bridge/nwl-dsi.c
 create mode 100644 drivers/gpu/drm/bridge/nwl-dsi.h

drivers/gpu/drm/bridge/Kconfig +16 -0

index 1cc9f502c1f2..13021f9a6107 100644
@@ -65,6 +65,22 @@ config DRM_MEGACHIPS_STDPXXXX_GE_B850V3_FW
           to DP++. This is used with the i.MX6 imx-ldb
           driver. You are likely to say N here.
 
+config DRM_NWL_MIPI_DSI
+	tristate "Northwest Logic MIPI DSI Host controller"
+	depends on DRM
+	depends on COMMON_CLK
+	depends on OF && HAS_IOMEM
+	select DRM_KMS_HELPER
+	select DRM_MIPI_DSI
+	select DRM_PANEL_BRIDGE
+	select GENERIC_PHY_MIPI_DPHY
+	select MFD_SYSCON
+	select MULTIPLEXER
+	select REGMAP_MMIO
+	help
+	  This enables the Northwest Logic MIPI DSI Host controller as
+	  for example found on NXP's i.MX8 Processors.
+
 config DRM_NXP_PTN3460
 	tristate "NXP PTN3460 DP/LVDS bridge"
 	depends on OF

drivers/gpu/drm/bridge/Makefile +3 -0

index 4934fcf5a6f8..c3f3a43e9b8f 100644
@@ -16,4 +16,7 @@ obj-$(CONFIG_DRM_ANALOGIX_DP) += analogix/
 obj-$(CONFIG_DRM_I2C_ADV7511) += adv7511/
 obj-$(CONFIG_DRM_TI_SN65DSI86) += ti-sn65dsi86.o
 obj-$(CONFIG_DRM_TI_TFP410) += ti-tfp410.o
+obj-$(CONFIG_DRM_NWL_MIPI_DSI) += nwl-dsi.o
 obj-y += synopsys/
+
+header-test-y += nwl-dsi.h

drivers/gpu/drm/bridge/nwl-dsi.c new file +85 -0

new file mode 100644
index 000000000000..dea5429a1e17
@@ -0,0 +1,1180 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * i.MX8 NWL MIPI DSI host driver
+ *
+ * Copyright (C) 2017 NXP
+ * Copyright (C) 2019 Purism SPC
+ */
+
+#include <linux/bitfield.h>
+#include <linux/clk.h>
+#include <linux/irq.h>
+#include <linux/math64.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/mux/consumer.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/phy/phy.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+#include <linux/sys_soc.h>
+#include <linux/time64.h>
+
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_bridge.h>
+#include <drm/drm_mipi_dsi.h>
+#include <drm/drm_of.h>
+#include <drm/drm_panel.h>
+#include <drm/drm_print.h>
+#include <drm/drm_probe_helper.h>
+
+#include <video/mipi_display.h>
+#include <video/videomode.h>
+
+#include "nwl-dsi.h"
+
+#define DRV_NAME "nwl-dsi"
+
+/* i.MX8 NWL quirks */
+/* i.MX8MQ errata E11418 */
+#define E11418_HS_MODE_QUIRK	BIT(0)
+/* Skip DSI bits in SRC on disable to avoid blank display on enable */
+#define SRC_RESET_QUIRK		BIT(1)
+
+#define NWL_DSI_MIPI_FIFO_TIMEOUT msecs_to_jiffies(500)
+
+enum transfer_direction {
+	DSI_PACKET_SEND,
+	DSI_PACKET_RECEIVE,
+};
+
+/* Possible platform specific clocks */
+#define NWL_DSI_CLK_CORE	    "core"
+#define NWL_DSI_MAX_PLATFORM_CLOCKS 1
+
+struct nwl_dsi_plat_clk_config {
+	const char *id;
+	struct clk *clk;
+	bool present;
+};
+
+struct nwl_dsi_transfer {
+	const struct mipi_dsi_msg *msg;
+	struct mipi_dsi_packet packet;
+	struct completion completed;
+
+	int status; /* status of transmission */
+	enum transfer_direction direction;
+	bool need_bta;
+	u8 cmd;
+	u16 rx_word_count;
+	size_t tx_len; /* in bytes */
+	size_t rx_len; /* in bytes */
+};
+
+struct nwl_dsi {
+	struct drm_bridge bridge;
+	struct mipi_dsi_host dsi_host;
+	struct drm_bridge *panel_bridge;
+	struct device *dev;
+	struct phy *phy;
+	union phy_configure_opts phy_cfg;
+	unsigned int quirks;
+
+	struct regmap *regmap;

drivers/gpu/drm/bridge/nwl-dsi.c new file +25 -0

+
+	/* dsi lanes */
+	u32 lanes;
+	enum mipi_dsi_pixel_format format;
+	struct drm_display_mode mode;
+	unsigned long dsi_mode_flags;
+
+	struct nwl_dsi_transfer *xfer;
+
+	const struct nwl_dsi_platform_data *pdata;
+};
+
+/* Platform specific hooks to enable other SoCs like the i.MX8QM */
+struct nwl_dsi_platform_data {
+	int (*poweron)(struct nwl_dsi *dsi);
+	int (*poweroff)(struct nwl_dsi *dsi);
+	int (*select_input)(struct nwl_dsi *dsi);
+	int (*deselect_input)(struct nwl_dsi *dsi);
+	struct nwl_dsi_plat_clk_config clk_config[NWL_DSI_MAX_PLATFORM_CLOCKS];
+};
+
+static const struct regmap_config nwl_dsi_regmap_config = {
+	.reg_bits = 16,
+	.val_bits = 32,
+	.reg_stride = 4,

drivers/gpu/drm/bridge/nwl-dsi.c new file +13 -0

+static int nwl_dsi_write(struct nwl_dsi *dsi, unsigned int reg, u32 val)
+{
+	int ret;
+
+	ret = regmap_write(dsi->regmap, reg, val);
+	if (ret < 0)
+		DRM_DEV_ERROR(dsi->dev,
+			      "Failed to write NWL DSI reg 0x%x: %d\n", reg,
+			      ret);
+	return ret;
+}
+
+static u32 nwl_dsi_read(struct nwl_dsi *dsi, u32 reg)

drivers/gpu/drm/bridge/nwl-dsi.c new file +5 -0

+}
+
+static u32 nwl_dsi_get_dpi_pixel_format(enum mipi_dsi_pixel_format format)
+{
+	switch (format) {

drivers/gpu/drm/bridge/nwl-dsi.c new file +94 -0

+	}
+}
+
+/*
+ * ps2bc - Picoseconds to byte clock cycles
+ */
+static u32 ps2bc(struct nwl_dsi *dsi, unsigned long long ps)
+{
+	u32 bpp = mipi_dsi_pixel_format_to_bpp(dsi->format);
+
+	return DIV64_U64_ROUND_UP(ps * dsi->mode.clock * bpp,
+				  dsi->lanes * 8 * NSEC_PER_SEC);
+}
+
+/*
+ * ui2bc - UI time periods to byte clock cycles
+ */
+static u32 ui2bc(struct nwl_dsi *dsi, unsigned long long ui)
+{
+	u32 bpp = mipi_dsi_pixel_format_to_bpp(dsi->format);
+
+	return DIV64_U64_ROUND_UP(ui * dsi->lanes,
+				  dsi->mode.clock * 1000 * bpp);
+}
+
+/*
+ * us2bc - micro seconds to lp clock cycles
+ */
+static u32 us2lp(u32 lp_clk_rate, unsigned long us)
+{
+	return DIV_ROUND_UP(us * lp_clk_rate, USEC_PER_SEC);
+}
+
+static int nwl_dsi_config_host(struct nwl_dsi *dsi)
+{
+	u32 cycles;
+	struct phy_configure_opts_mipi_dphy *cfg = &dsi->phy_cfg.mipi_dphy;
+
+	if (dsi->lanes < 1 || dsi->lanes > 4)
+		return -EINVAL;
+
+	DRM_DEV_DEBUG_DRIVER(dsi->dev, "DSI Lanes %d\n", dsi->lanes);
+	nwl_dsi_write(dsi, NWL_DSI_CFG_NUM_LANES, dsi->lanes - 1);
+
+	if (dsi->dsi_mode_flags & MIPI_DSI_CLOCK_NON_CONTINUOUS) {
+		nwl_dsi_write(dsi, NWL_DSI_CFG_NONCONTINUOUS_CLK, 0x01);
+		nwl_dsi_write(dsi, NWL_DSI_CFG_AUTOINSERT_EOTP, 0x01);
+	} else {
+		nwl_dsi_write(dsi, NWL_DSI_CFG_NONCONTINUOUS_CLK, 0x00);
+		nwl_dsi_write(dsi, NWL_DSI_CFG_AUTOINSERT_EOTP, 0x00);
+	}
+
+	/* values in byte clock cycles */
+	cycles = ui2bc(dsi, cfg->clk_pre);
+	DRM_DEV_DEBUG_DRIVER(dsi->dev, "cfg_t_pre: 0x%x\n", cycles);
+	nwl_dsi_write(dsi, NWL_DSI_CFG_T_PRE, cycles);
+	cycles = ps2bc(dsi, cfg->lpx + cfg->clk_prepare + cfg->clk_zero);
+	DRM_DEV_DEBUG_DRIVER(dsi->dev, "cfg_tx_gap (pre): 0x%x\n", cycles);
+	cycles += ui2bc(dsi, cfg->clk_pre);
+	DRM_DEV_DEBUG_DRIVER(dsi->dev, "cfg_t_post: 0x%x\n", cycles);
+	nwl_dsi_write(dsi, NWL_DSI_CFG_T_POST, cycles);
+	cycles = ps2bc(dsi, cfg->hs_exit);
+	DRM_DEV_DEBUG_DRIVER(dsi->dev, "cfg_tx_gap: 0x%x\n", cycles);
+	nwl_dsi_write(dsi, NWL_DSI_CFG_TX_GAP, cycles);
+
+	nwl_dsi_write(dsi, NWL_DSI_CFG_EXTRA_CMDS_AFTER_EOTP, 0x01);
+	nwl_dsi_write(dsi, NWL_DSI_CFG_HTX_TO_COUNT, 0x00);
+	nwl_dsi_write(dsi, NWL_DSI_CFG_LRX_H_TO_COUNT, 0x00);
+	nwl_dsi_write(dsi, NWL_DSI_CFG_BTA_H_TO_COUNT, 0x00);
+	/* In LP clock cycles */
+	cycles = us2lp(cfg->lp_clk_rate, cfg->wakeup);
+	DRM_DEV_DEBUG_DRIVER(dsi->dev, "cfg_twakeup: 0x%x\n", cycles);
+	nwl_dsi_write(dsi, NWL_DSI_CFG_TWAKEUP, cycles);
+
+	return 0;
+}
+
+static int nwl_dsi_config_dpi(struct nwl_dsi *dsi)
+{
+	u32 color_format, mode;
+	bool burst_mode;
+	int hfront_porch, hback_porch, vfront_porch, vback_porch;
+	int hsync_len, vsync_len;
+
+	hfront_porch = dsi->mode.hsync_start - dsi->mode.hdisplay;
+	hsync_len = dsi->mode.hsync_end - dsi->mode.hsync_start;
+	hback_porch = dsi->mode.htotal - dsi->mode.hsync_end;
+
+	vfront_porch = dsi->mode.vsync_start - dsi->mode.vdisplay;
+	vsync_len = dsi->mode.vsync_end - dsi->mode.vsync_start;
+	vback_porch = dsi->mode.vtotal - dsi->mode.vsync_end;
+
+	DRM_DEV_DEBUG_DRIVER(dsi->dev, "hfront_porch = %d\n", hfront_porch);
+	DRM_DEV_DEBUG_DRIVER(dsi->dev, "hback_porch = %d\n", hback_porch);

drivers/gpu/drm/bridge/nwl-dsi.c new file +35 -0

+		DRM_DEV_ERROR(dsi->dev, "Invalid color format 0x%x\n",
+			      dsi->format);
+		return color_format;
+	}
+	DRM_DEV_DEBUG_DRIVER(dsi->dev, "pixel fmt = %d\n", dsi->format);
+
+	nwl_dsi_write(dsi, NWL_DSI_INTERFACE_COLOR_CODING, NWL_DSI_DPI_24_BIT);
+	nwl_dsi_write(dsi, NWL_DSI_PIXEL_FORMAT, color_format);
+	/*
+	 * Adjusting input polarity based on the video mode results in
+	 * a black screen so always pick active low:
+	 */
+	nwl_dsi_write(dsi, NWL_DSI_VSYNC_POLARITY,
+		      NWL_DSI_VSYNC_POLARITY_ACTIVE_LOW);
+	nwl_dsi_write(dsi, NWL_DSI_HSYNC_POLARITY,
+		      NWL_DSI_HSYNC_POLARITY_ACTIVE_LOW);
+
+	burst_mode = (dsi->dsi_mode_flags & MIPI_DSI_MODE_VIDEO_BURST) &&
+		     !(dsi->dsi_mode_flags & MIPI_DSI_MODE_VIDEO_SYNC_PULSE);
+
+	if (burst_mode) {
+		nwl_dsi_write(dsi, NWL_DSI_VIDEO_MODE, NWL_DSI_VM_BURST_MODE);
+		nwl_dsi_write(dsi, NWL_DSI_PIXEL_FIFO_SEND_LEVEL, 256);
+	} else {
+		mode = ((dsi->dsi_mode_flags & MIPI_DSI_MODE_VIDEO_SYNC_PULSE) ?
+				NWL_DSI_VM_BURST_MODE_WITH_SYNC_PULSES :
+				NWL_DSI_VM_NON_BURST_MODE_WITH_SYNC_EVENTS);
+		nwl_dsi_write(dsi, NWL_DSI_VIDEO_MODE, mode);
+		nwl_dsi_write(dsi, NWL_DSI_PIXEL_FIFO_SEND_LEVEL,
+			      dsi->mode.hdisplay);
+	}
+
+	nwl_dsi_write(dsi, NWL_DSI_HFP, hfront_porch);
+	nwl_dsi_write(dsi, NWL_DSI_HBP, hback_porch);
+	nwl_dsi_write(dsi, NWL_DSI_HSA, hsync_len);

drivers/gpu/drm/bridge/nwl-dsi.c new file +5 -0

+
+	return 0;
+}
+
+static void nwl_dsi_init_interrupts(struct nwl_dsi *dsi)

drivers/gpu/drm/bridge/nwl-dsi.c new file +8 -0

+
+	nwl_dsi_write(dsi, NWL_DSI_IRQ_MASK, irq_enable);
+}
+
+static int nwl_dsi_host_attach(struct mipi_dsi_host *dsi_host,
+			       struct mipi_dsi_device *device)
+{
+	struct nwl_dsi *dsi = container_of(dsi_host, struct nwl_dsi, dsi_host);

drivers/gpu/drm/bridge/nwl-dsi.c new file +358 -0

+
+	dsi->lanes = device->lanes;
+	dsi->format = device->format;
+	dsi->dsi_mode_flags = device->mode_flags;
+
+	ret = drm_of_find_panel_or_bridge(dsi->dev->of_node, 1, 0, &panel,
+					  &bridge);
+	if (ret)
+		return ret;
+
+	if (panel) {
+		bridge = drm_panel_bridge_add(panel, DRM_MODE_CONNECTOR_DSI);
+		if (IS_ERR(bridge))
+			return PTR_ERR(bridge);
+	}
+
+	dsi->panel_bridge = bridge;
+	drm_bridge_add(&dsi->bridge);
+
+	return 0;
+}
+
+static int nwl_dsi_host_detach(struct mipi_dsi_host *dsi_host,
+			       struct mipi_dsi_device *device)
+{
+	struct nwl_dsi *dsi = container_of(dsi_host, struct nwl_dsi, dsi_host);
+
+	drm_of_panel_bridge_remove(dsi->dev->of_node, 1, 0);
+	drm_bridge_remove(&dsi->bridge);
+
+	return 0;
+}
+
+static bool nwl_dsi_read_packet(struct nwl_dsi *dsi, u32 status)
+{
+	struct device *dev = dsi->dev;
+	struct nwl_dsi_transfer *xfer = dsi->xfer;
+	u8 *payload = xfer->msg->rx_buf;
+	u32 val;
+	u16 word_count;
+	u8 channel;
+	u8 data_type;
+
+	xfer->status = 0;
+
+	if (xfer->rx_word_count == 0) {
+		if (!(status & NWL_DSI_RX_PKT_HDR_RCVD))
+			return false;
+		/* Get the RX header and parse it */
+		val = nwl_dsi_read(dsi, NWL_DSI_RX_PKT_HEADER);
+		word_count = NWL_DSI_WC(val);
+		channel = NWL_DSI_RX_VC(val);
+		data_type = NWL_DSI_RX_DT(val);
+
+		if (channel != xfer->msg->channel) {
+			DRM_DEV_ERROR(dev,
+				      "[%02X] Channel mismatch (%u != %u)\n",
+				      xfer->cmd, channel, xfer->msg->channel);
+			return true;
+		}
+
+		switch (data_type) {
+		case MIPI_DSI_RX_GENERIC_SHORT_READ_RESPONSE_2BYTE:
+			/* Fall through */
+		case MIPI_DSI_RX_DCS_SHORT_READ_RESPONSE_2BYTE:
+			if (xfer->msg->rx_len > 1) {
+				/* read second byte */
+				payload[1] = word_count >> 8;
+				++xfer->rx_len;
+			}
+			/* Fall through */
+		case MIPI_DSI_RX_GENERIC_SHORT_READ_RESPONSE_1BYTE:
+			/* Fall through */
+		case MIPI_DSI_RX_DCS_SHORT_READ_RESPONSE_1BYTE:
+			if (xfer->msg->rx_len > 0) {
+				/* read first byte */
+				payload[0] = word_count & 0xff;
+				++xfer->rx_len;
+			}
+			xfer->status = xfer->rx_len;
+			return true;
+		case MIPI_DSI_RX_ACKNOWLEDGE_AND_ERROR_REPORT:
+			word_count &= 0xff;
+			DRM_DEV_ERROR(dev, "[%02X] DSI error report: 0x%02x\n",
+				      xfer->cmd, word_count);
+			xfer->status = -EPROTO;
+			return true;
+		}
+
+		if (word_count > xfer->msg->rx_len) {
+			DRM_DEV_ERROR(
+				dev,
+				"[%02X] Receive buffer too small: %zu (< %u)\n",
+				xfer->cmd, xfer->msg->rx_len, word_count);
+			return true;
+		}
+
+		xfer->rx_word_count = word_count;
+	} else {
+		/* Set word_count from previous header read */
+		word_count = xfer->rx_word_count;
+	}
+
+	/* If RX payload is not yet received, wait for it */
+	if (!(status & NWL_DSI_RX_PKT_PAYLOAD_DATA_RCVD))
+		return false;
+
+	/* Read the RX payload */
+	while (word_count >= 4) {
+		val = nwl_dsi_read(dsi, NWL_DSI_RX_PAYLOAD);
+		payload[0] = (val >> 0) & 0xff;
+		payload[1] = (val >> 8) & 0xff;
+		payload[2] = (val >> 16) & 0xff;
+		payload[3] = (val >> 24) & 0xff;
+		payload += 4;
+		xfer->rx_len += 4;
+		word_count -= 4;
+	}
+
+	if (word_count > 0) {
+		val = nwl_dsi_read(dsi, NWL_DSI_RX_PAYLOAD);
+		switch (word_count) {
+		case 3:
+			payload[2] = (val >> 16) & 0xff;
+			++xfer->rx_len;
+			/* Fall through */
+		case 2:
+			payload[1] = (val >> 8) & 0xff;
+			++xfer->rx_len;
+			/* Fall through */
+		case 1:
+			payload[0] = (val >> 0) & 0xff;
+			++xfer->rx_len;
+			break;
+		}
+	}
+
+	xfer->status = xfer->rx_len;
+
+	return true;
+}
+
+static void nwl_dsi_finish_transmission(struct nwl_dsi *dsi, u32 status)
+{
+	struct nwl_dsi_transfer *xfer = dsi->xfer;
+	bool end_packet = false;
+
+	if (!xfer)
+		return;
+
+	if (xfer->direction == DSI_PACKET_SEND &&
+	    status & NWL_DSI_TX_PKT_DONE) {
+		xfer->status = xfer->tx_len;
+		end_packet = true;
+	} else if (status & NWL_DSI_DPHY_DIRECTION &&
+		   ((status & (NWL_DSI_RX_PKT_HDR_RCVD |
+			       NWL_DSI_RX_PKT_PAYLOAD_DATA_RCVD)))) {
+		end_packet = nwl_dsi_read_packet(dsi, status);
+	}
+
+	if (end_packet)
+		complete(&xfer->completed);
+}
+
+static void nwl_dsi_begin_transmission(struct nwl_dsi *dsi)
+{
+	struct nwl_dsi_transfer *xfer = dsi->xfer;
+	struct mipi_dsi_packet *pkt = &xfer->packet;
+	const u8 *payload;
+	size_t length;
+	u16 word_count;
+	u8 hs_mode;
+	u32 val;
+	u32 hs_workaround = 0;
+
+	/* Send the payload, if any */
+	length = pkt->payload_length;
+	payload = pkt->payload;
+
+	while (length >= 4) {
+		val = *(u32 *)payload;
+		hs_workaround |= !(val & 0xFFFF00);
+		nwl_dsi_write(dsi, NWL_DSI_TX_PAYLOAD, val);
+		payload += 4;
+		length -= 4;
+	}
+	/* Send the rest of the payload */
+	val = 0;
+	switch (length) {
+	case 3:
+		val |= payload[2] << 16;
+		/* Fall through */
+	case 2:
+		val |= payload[1] << 8;
+		hs_workaround |= !(val & 0xFFFF00);
+		/* Fall through */
+	case 1:
+		val |= payload[0];
+		nwl_dsi_write(dsi, NWL_DSI_TX_PAYLOAD, val);
+		break;
+	}
+	xfer->tx_len = pkt->payload_length;
+
+	/*
+	 * Send the header
+	 * header[0] = Virtual Channel + Data Type
+	 * header[1] = Word Count LSB (LP) or first param (SP)
+	 * header[2] = Word Count MSB (LP) or second param (SP)
+	 */
+	word_count = pkt->header[1] | (pkt->header[2] << 8);
+	if (hs_workaround && (dsi->quirks & E11418_HS_MODE_QUIRK)) {
+		DRM_DEV_DEBUG_DRIVER(dsi->dev,
+				     "Using hs mode workaround for cmd 0x%x\n",
+				     xfer->cmd);
+		hs_mode = 1;
+	} else {
+		hs_mode = (xfer->msg->flags & MIPI_DSI_MSG_USE_LPM) ? 0 : 1;
+	}
+	val = NWL_DSI_WC(word_count) | NWL_DSI_TX_VC(xfer->msg->channel) |
+	      NWL_DSI_TX_DT(xfer->msg->type) | NWL_DSI_HS_SEL(hs_mode) |
+	      NWL_DSI_BTA_TX(xfer->need_bta);
+	nwl_dsi_write(dsi, NWL_DSI_PKT_CONTROL, val);
+
+	/* Send packet command */
+	nwl_dsi_write(dsi, NWL_DSI_SEND_PACKET, 0x1);
+}
+
+static ssize_t nwl_dsi_host_transfer(struct mipi_dsi_host *dsi_host,
+				     const struct mipi_dsi_msg *msg)
+{
+	struct nwl_dsi *dsi = container_of(dsi_host, struct nwl_dsi, dsi_host);
+	struct nwl_dsi_transfer xfer;
+	ssize_t ret = 0;
+
+	/* Create packet to be sent */
+	dsi->xfer = &xfer;
+	ret = mipi_dsi_create_packet(&xfer.packet, msg);
+	if (ret < 0) {
+		dsi->xfer = NULL;
+		return ret;
+	}
+
+	if ((msg->type & MIPI_DSI_GENERIC_READ_REQUEST_0_PARAM ||
+	     msg->type & MIPI_DSI_GENERIC_READ_REQUEST_1_PARAM ||
+	     msg->type & MIPI_DSI_GENERIC_READ_REQUEST_2_PARAM ||
+	     msg->type & MIPI_DSI_DCS_READ) &&
+	    msg->rx_len > 0 && msg->rx_buf != NULL)
+		xfer.direction = DSI_PACKET_RECEIVE;
+	else
+		xfer.direction = DSI_PACKET_SEND;
+
+	xfer.need_bta = (xfer.direction == DSI_PACKET_RECEIVE);
+	xfer.need_bta |= (msg->flags & MIPI_DSI_MSG_REQ_ACK) ? 1 : 0;
+	xfer.msg = msg;
+	xfer.status = -ETIMEDOUT;
+	xfer.rx_word_count = 0;
+	xfer.rx_len = 0;
+	xfer.cmd = 0x00;
+	if (msg->tx_len > 0)
+		xfer.cmd = ((u8 *)(msg->tx_buf))[0];
+	init_completion(&xfer.completed);
+
+	ret = clk_prepare_enable(dsi->rx_esc_clk);
+	if (ret < 0) {
+		DRM_DEV_ERROR(dsi->dev, "Failed to enable rx_esc clk: %zd\n",
+			      ret);
+		return ret;
+	}
+	DRM_DEV_DEBUG_DRIVER(dsi->dev, "Enabled rx_esc clk @%lu Hz\n",
+			     clk_get_rate(dsi->rx_esc_clk));
+
+	/* Initiate the DSI packet transmision */
+	nwl_dsi_begin_transmission(dsi);
+
+	if (!wait_for_completion_timeout(&xfer.completed,
+					 NWL_DSI_MIPI_FIFO_TIMEOUT)) {
+		DRM_DEV_ERROR(dsi_host->dev, "[%02X] DSI transfer timed out\n",
+			      xfer.cmd);
+		ret = -ETIMEDOUT;
+	} else {
+		ret = xfer.status;
+	}
+
+	clk_disable_unprepare(dsi->rx_esc_clk);
+
+	return ret;
+}
+
+static const struct mipi_dsi_host_ops nwl_dsi_host_ops = {
+	.attach = nwl_dsi_host_attach,
+	.detach = nwl_dsi_host_detach,
+	.transfer = nwl_dsi_host_transfer,
+};
+
+static irqreturn_t nwl_dsi_irq_handler(int irq, void *data)
+{
+	u32 irq_status;
+	struct nwl_dsi *dsi = data;
+
+	irq_status = nwl_dsi_read(dsi, NWL_DSI_IRQ_STATUS);
+
+	if (irq_status & NWL_DSI_TX_FIFO_OVFLW)
+		DRM_DEV_ERROR_RATELIMITED(dsi->dev, "tx fifo overflow\n");
+
+	if (irq_status & NWL_DSI_HS_TX_TIMEOUT)
+		DRM_DEV_ERROR_RATELIMITED(dsi->dev, "HS tx timeout\n");
+
+	if (irq_status & NWL_DSI_TX_PKT_DONE ||
+	    irq_status & NWL_DSI_RX_PKT_HDR_RCVD ||
+	    irq_status & NWL_DSI_RX_PKT_PAYLOAD_DATA_RCVD)
+		nwl_dsi_finish_transmission(dsi, irq_status);
+
+	return IRQ_HANDLED;
+}
+
+static int nwl_dsi_enable(struct nwl_dsi *dsi)
+{
+	struct device *dev = dsi->dev;
+	union phy_configure_opts *phy_cfg = &dsi->phy_cfg;
+	int ret;
+
+	if (!dsi->lanes) {
+		DRM_DEV_ERROR(dev, "Need DSI lanes: %d\n", dsi->lanes);
+		return -EINVAL;
+	}
+
+	ret = phy_init(dsi->phy);
+	if (ret < 0) {
+		DRM_DEV_ERROR(dev, "Failed to init DSI phy: %d\n", ret);
+		return ret;
+	}
+
+	ret = phy_configure(dsi->phy, phy_cfg);
+	if (ret < 0) {
+		DRM_DEV_ERROR(dev, "Failed to configure DSI phy: %d\n", ret);
+		return ret;
+	}
+
+	ret = clk_prepare_enable(dsi->tx_esc_clk);
+	if (ret < 0) {
+		DRM_DEV_ERROR(dsi->dev, "Failed to enable tx_esc clk: %d\n",
+			      ret);
+		return ret;
+	}
+	DRM_DEV_DEBUG_DRIVER(dsi->dev, "Enabled tx_esc clk @%lu Hz\n",
+			     clk_get_rate(dsi->tx_esc_clk));
+
+	ret = nwl_dsi_config_host(dsi);
+	if (ret < 0) {
+		DRM_DEV_ERROR(dev, "Failed to set up DSI: %d", ret);
+		return ret;
+	}
+
+	ret = nwl_dsi_config_dpi(dsi);
+	if (ret < 0) {
+		DRM_DEV_ERROR(dev, "Failed to set up DPI: %d", ret);
+		return ret;
+	}

drivers/gpu/drm/bridge/nwl-dsi.c new file +177 -0

+}
+
+static int nwl_dsi_disable(struct nwl_dsi *dsi)
+{
+	struct device *dev = dsi->dev;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "Disabling clocks and phy\n");
+
+	phy_power_off(dsi->phy);
+	phy_exit(dsi->phy);
+
+	/* Disabling the clock before the phy breaks enabling dsi again */
+	clk_disable_unprepare(dsi->tx_esc_clk);
+
+	return 0;
+}
+
+static int nwl_dsi_set_platform_clocks(struct nwl_dsi *dsi, bool enable)
+{
+	struct device *dev = dsi->dev;
+	const char *id;
+	struct clk *clk;
+	size_t i;
+	unsigned long rate;
+	int ret, result = 0;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "%s platform clocks\n",
+			     enable ? "enabling" : "disabling");
+	for (i = 0; i < ARRAY_SIZE(dsi->pdata->clk_config); i++) {
+		if (!dsi->clk_config[i].present)
+			continue;
+		id = dsi->clk_config[i].id;
+		clk = dsi->clk_config[i].clk;
+
+		if (enable) {
+			ret = clk_prepare_enable(clk);
+			if (ret < 0) {
+				DRM_DEV_ERROR(dev,
+					      "Failed to enable %s clk: %d\n",
+					      id, ret);
+				result = result ?: ret;
+			}
+			rate = clk_get_rate(clk);
+			DRM_DEV_DEBUG_DRIVER(dev, "Enabled %s clk @%lu Hz\n",
+					     id, rate);
+		} else {
+			clk_disable_unprepare(clk);
+			DRM_DEV_DEBUG_DRIVER(dev, "Disabled %s clk\n", id);
+		}
+	}
+
+	return result;
+}
+
+static int nwl_dsi_plat_enable(struct nwl_dsi *dsi)
+{
+	struct device *dev = dsi->dev;
+	int ret;
+
+	if (dsi->pdata->select_input)
+		dsi->pdata->select_input(dsi);
+
+	ret = nwl_dsi_set_platform_clocks(dsi, true);
+	if (ret < 0)
+		return ret;
+
+	ret = dsi->pdata->poweron(dsi);
+	if (ret < 0)
+		DRM_DEV_ERROR(dev, "Failed to power on DSI: %d\n", ret);
+	return ret;
+}
+
+static void nwl_dsi_plat_disable(struct nwl_dsi *dsi)
+{
+	dsi->pdata->poweroff(dsi);
+	nwl_dsi_set_platform_clocks(dsi, false);
+	if (dsi->pdata->deselect_input)
+		dsi->pdata->deselect_input(dsi);
+}
+
+static void nwl_dsi_bridge_disable(struct drm_bridge *bridge)
+{
+	struct nwl_dsi *dsi = bridge_to_dsi(bridge);
+
+	nwl_dsi_disable(dsi);
+	nwl_dsi_plat_disable(dsi);
+	pm_runtime_put(dsi->dev);
+}
+
+static int nwl_dsi_get_dphy_params(struct nwl_dsi *dsi,
+				   const struct drm_display_mode *mode,
+				   union phy_configure_opts *phy_opts)
+{
+	unsigned long rate;
+	int ret;
+
+	if (dsi->lanes < 1 || dsi->lanes > 4)
+		return -EINVAL;
+
+	/*
+	 * So far the DPHY spec minimal timings work for both mixel
+	 * dphy and nwl dsi host
+	 */
+	ret = phy_mipi_dphy_get_default_config(
+		mode->crtc_clock * 1000,
+		mipi_dsi_pixel_format_to_bpp(dsi->format), dsi->lanes,
+		&phy_opts->mipi_dphy);
+	if (ret < 0)
+		return ret;
+
+	rate = clk_get_rate(dsi->tx_esc_clk);
+	DRM_DEV_DEBUG_DRIVER(dsi->dev, "LP clk is @%lu Hz\n", rate);
+	phy_opts->mipi_dphy.lp_clk_rate = rate;
+
+	return 0;
+}
+
+static bool nwl_dsi_bridge_mode_fixup(struct drm_bridge *bridge,
+				      const struct drm_display_mode *mode,
+				      struct drm_display_mode *adjusted_mode)
+{
+	/* At least LCDIF + NWL needs active high sync */
+	adjusted_mode->flags |= (DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC);
+	adjusted_mode->flags &= ~(DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC);
+
+	return true;
+}
+
+static enum drm_mode_status
+nwl_dsi_bridge_mode_valid(struct drm_bridge *bridge,
+			  const struct drm_display_mode *mode)
+{
+	struct nwl_dsi *dsi = bridge_to_dsi(bridge);
+	int bpp = mipi_dsi_pixel_format_to_bpp(dsi->format);
+
+	if (mode->clock * bpp > 15000000 * dsi->lanes)
+		return MODE_CLOCK_HIGH;
+
+	if (mode->clock * bpp < 80000 * dsi->lanes)
+		return MODE_CLOCK_LOW;
+
+	return MODE_OK;
+}
+
+static void
+nwl_dsi_bridge_mode_set(struct drm_bridge *bridge,
+			const struct drm_display_mode *mode,
+			const struct drm_display_mode *adjusted_mode)
+{
+	struct nwl_dsi *dsi = bridge_to_dsi(bridge);
+	struct device *dev = dsi->dev;
+	union phy_configure_opts new_cfg;
+	unsigned long phy_ref_rate;
+	int ret;
+
+	ret = nwl_dsi_get_dphy_params(dsi, adjusted_mode, &new_cfg);
+	if (ret < 0)
+		return;
+
+	/*
+	 * If hs clock is unchanged, we're all good - all parameters are
+	 * derived from it atm.
+	 */
+	if (new_cfg.mipi_dphy.hs_clk_rate == dsi->phy_cfg.mipi_dphy.hs_clk_rate)
+		return;
+
+	phy_ref_rate = clk_get_rate(dsi->phy_ref_clk);
+	DRM_DEV_DEBUG_DRIVER(dev, "PHY at ref rate: %lu\n", phy_ref_rate);
+	/* Save the new desired phy config */
+	memcpy(&dsi->phy_cfg, &new_cfg, sizeof(new_cfg));
+
+	memcpy(&dsi->mode, adjusted_mode, sizeof(dsi->mode));
+	drm_mode_debug_printmodeline(adjusted_mode);
+}
+
+static void nwl_dsi_bridge_pre_enable(struct drm_bridge *bridge)
+{

drivers/gpu/drm/bridge/nwl-dsi.c new file +39 -0

+
+	return drm_bridge_attach(bridge->encoder, dsi->panel_bridge, bridge);
+}
+
+static const struct drm_bridge_funcs nwl_dsi_bridge_funcs = {
+	.pre_enable = nwl_dsi_bridge_pre_enable,
+	.disable    = nwl_dsi_bridge_disable,
+	.mode_fixup = nwl_dsi_bridge_mode_fixup,
+	.mode_set   = nwl_dsi_bridge_mode_set,
+	.mode_valid = nwl_dsi_bridge_mode_valid,
+	.attach	    = nwl_dsi_bridge_attach,
+};
+
+static int nwl_dsi_parse_dt(struct nwl_dsi *dsi)
+{
+	struct platform_device *pdev = to_platform_device(dsi->dev);
+	struct clk *clk;
+	const char *clk_id;
+	void __iomem *base;
+	int i, ret;
+
+	dsi->phy = devm_phy_get(dsi->dev, "dphy");
+	if (IS_ERR(dsi->phy)) {
+		ret = PTR_ERR(dsi->phy);
+		if (ret != -EPROBE_DEFER)
+			DRM_DEV_ERROR(dsi->dev, "Could not get PHY: %d\n", ret);
+		return ret;
+	}
+
+	/* Platform dependent clocks */
+	memcpy(dsi->clk_config, dsi->pdata->clk_config,
+	       sizeof(dsi->pdata->clk_config));
+
+	for (i = 0; i < ARRAY_SIZE(dsi->pdata->clk_config); i++) {
+		if (!dsi->clk_config[i].present)
+			continue;
+
+		clk_id = dsi->clk_config[i].id;
+		clk = devm_clk_get(dsi->dev, clk_id);

drivers/gpu/drm/bridge/nwl-dsi.c new file +53 -0

+
+	/* DSI clocks */
+	clk = devm_clk_get(dsi->dev, "phy_ref");
+	if (IS_ERR(clk)) {
+		ret = PTR_ERR(clk);
+		DRM_DEV_ERROR(dsi->dev, "Failed to get phy_ref clock: %d\n",
+			      ret);
+		return ret;
+	}
+	dsi->phy_ref_clk = clk;
+
+	clk = devm_clk_get(dsi->dev, "rx_esc");
+	if (IS_ERR(clk)) {
+		ret = PTR_ERR(clk);
+		DRM_DEV_ERROR(dsi->dev, "Failed to get rx_esc clock: %d\n",
+			      ret);
+		return ret;
+	}
+	dsi->rx_esc_clk = clk;
+
+	clk = devm_clk_get(dsi->dev, "tx_esc");
+	if (IS_ERR(clk)) {
+		ret = PTR_ERR(clk);
+		DRM_DEV_ERROR(dsi->dev, "Failed to get tx_esc clock: %d\n",
+			      ret);
+		return ret;
+	}
+	dsi->tx_esc_clk = clk;
+
+	dsi->mux = devm_mux_control_get(dsi->dev, NULL);
+	if (IS_ERR(dsi->mux)) {
+		ret = PTR_ERR(dsi->mux);
+		if (ret != -EPROBE_DEFER)
+			DRM_DEV_ERROR(dsi->dev, "Failed to get mux: %d\n", ret);
+		return ret;
+	}
+
+	base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(base))
+		return PTR_ERR(base);
+
+	dsi->regmap =
+		devm_regmap_init_mmio(dsi->dev, base, &nwl_dsi_regmap_config);
+	if (IS_ERR(dsi->regmap)) {
+		ret = PTR_ERR(dsi->regmap);
+		DRM_DEV_ERROR(dsi->dev, "Failed to create NWL DSI regmap: %d\n",
+			      ret);
+		return ret;
+	}
+
+	dsi->irq = platform_get_irq(pdev, 0);
+	if (dsi->irq < 0) {
+		DRM_DEV_ERROR(dsi->dev, "Failed to get device IRQ: %d\n",

drivers/gpu/drm/bridge/nwl-dsi.c new file +150 -0

+
+	DRM_DEV_INFO(dsi->dev, "Using %s as input source\n",
+		     (use_dcss) ? "DCSS" : "LCDIF");
+
+	ret = mux_control_try_select(dsi->mux, use_dcss);
+	if (ret < 0)
+		DRM_DEV_ERROR(dsi->dev, "Failed to select input: %d\n", ret);
+
+	of_node_put(remote);
+	return ret;
+}
+
+
+static int imx8mq_dsi_deselect_input(struct nwl_dsi *dsi)
+{
+	int ret;
+
+	ret = mux_control_deselect(dsi->mux);
+	if (ret < 0)
+		DRM_DEV_ERROR(dsi->dev, "Failed to deselect input: %d\n", ret);
+
+	return ret;
+}
+
+
+static int imx8mq_dsi_poweron(struct nwl_dsi *dsi)
+{
+	int ret = 0;
+
+	/* otherwise the display stays blank */
+	usleep_range(200, 300);
+
+	if (dsi->rstc)
+		ret = reset_control_deassert(dsi->rstc);
+
+	return ret;
+}
+
+static int imx8mq_dsi_poweroff(struct nwl_dsi *dsi)
+{
+	int ret = 0;
+
+	if (dsi->quirks & SRC_RESET_QUIRK)
+		return 0;
+
+	if (dsi->rstc)
+		ret = reset_control_assert(dsi->rstc);
+	return ret;
+}
+
+static const struct drm_bridge_timings nwl_dsi_timings = {
+	.input_bus_flags = DRM_BUS_FLAG_DE_LOW,
+};
+
+static const struct nwl_dsi_platform_data imx8mq_dev = {
+	.poweron = &imx8mq_dsi_poweron,
+	.poweroff = &imx8mq_dsi_poweroff,
+	.select_input = &imx8mq_dsi_select_input,
+	.deselect_input = &imx8mq_dsi_deselect_input,
+	.clk_config = {
+		{ .id = NWL_DSI_CLK_CORE, .present = true },
+	},
+};
+
+static const struct of_device_id nwl_dsi_dt_ids[] = {
+	{ .compatible = "fsl,imx8mq-nwl-dsi", .data = &imx8mq_dev, },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, nwl_dsi_dt_ids);
+
+static const struct soc_device_attribute nwl_dsi_quirks_match[] = {
+	{ .soc_id = "i.MX8MQ", .revision = "2.0",
+	  .data = (void *)(E11418_HS_MODE_QUIRK | SRC_RESET_QUIRK) },
+	{ /* sentinel. */ },
+};
+
+static int nwl_dsi_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	const struct of_device_id *of_id = of_match_device(nwl_dsi_dt_ids, dev);
+	const struct nwl_dsi_platform_data *pdata = of_id->data;
+	const struct soc_device_attribute *attr;
+	struct nwl_dsi *dsi;
+	int ret;
+
+	dsi = devm_kzalloc(dev, sizeof(*dsi), GFP_KERNEL);
+	if (!dsi)
+		return -ENOMEM;
+
+	dsi->dev = dev;
+	dsi->pdata = pdata;
+
+	ret = nwl_dsi_parse_dt(dsi);
+	if (ret)
+		return ret;
+
+	ret = devm_request_irq(dev, dsi->irq, nwl_dsi_irq_handler, 0,
+			       dev_name(dev), dsi);
+	if (ret < 0) {
+		DRM_DEV_ERROR(dev, "Failed to request IRQ %d: %d\n", dsi->irq,
+			      ret);
+		return ret;
+	}
+
+	dsi->dsi_host.ops = &nwl_dsi_host_ops;
+	dsi->dsi_host.dev = dev;
+	ret = mipi_dsi_host_register(&dsi->dsi_host);
+	if (ret) {
+		DRM_DEV_ERROR(dev, "Failed to register MIPI host: %d\n", ret);
+		return ret;
+	}
+
+	attr = soc_device_match(nwl_dsi_quirks_match);
+	if (attr)
+		dsi->quirks = (uintptr_t)attr->data;
+
+	dsi->bridge.driver_private = dsi;
+	dsi->bridge.funcs = &nwl_dsi_bridge_funcs;
+	dsi->bridge.of_node = dev->of_node;
+	dsi->bridge.timings = &nwl_dsi_timings;
+
+	dev_set_drvdata(dev, dsi);
+	pm_runtime_enable(dev);
+	return 0;
+}
+
+static int nwl_dsi_remove(struct platform_device *pdev)
+{
+	struct nwl_dsi *dsi = platform_get_drvdata(pdev);
+
+	mipi_dsi_host_unregister(&dsi->dsi_host);
+	pm_runtime_disable(&pdev->dev);
+	return 0;
+}
+
+static struct platform_driver nwl_dsi_driver = {
+	.probe		= nwl_dsi_probe,
+	.remove		= nwl_dsi_remove,
+	.driver		= {
+		.of_match_table = nwl_dsi_dt_ids,
+		.name	= DRV_NAME,
+	},
+};
+
+module_platform_driver(nwl_dsi_driver);
+
+MODULE_AUTHOR("NXP Semiconductor");
+MODULE_AUTHOR("Purism SPC");
+MODULE_DESCRIPTION("Northwest Logic MIPI-DSI driver");
+MODULE_LICENSE("GPL"); /* GPLv2 or later */

drivers/gpu/drm/bridge/nwl-dsi.h new file +134 -0

new file mode 100644
index 000000000000..a247a8a11c7c
@@ -0,0 +1,144 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * NWL MIPI DSI host driver
+ *
+ * Copyright (C) 2017 NXP
+ * Copyright (C) 2019 Purism SPC
+ */
+#ifndef __NWL_DSI_H__
+#define __NWL_DSI_H__
+
+/* DSI HOST registers */
+#define NWL_DSI_CFG_NUM_LANES			0x0
+#define NWL_DSI_CFG_NONCONTINUOUS_CLK		0x4
+#define NWL_DSI_CFG_T_PRE			0x8
+#define NWL_DSI_CFG_T_POST			0xc
+#define NWL_DSI_CFG_TX_GAP			0x10
+#define NWL_DSI_CFG_AUTOINSERT_EOTP		0x14
+#define NWL_DSI_CFG_EXTRA_CMDS_AFTER_EOTP	0x18
+#define NWL_DSI_CFG_HTX_TO_COUNT		0x1c
+#define NWL_DSI_CFG_LRX_H_TO_COUNT		0x20
+#define NWL_DSI_CFG_BTA_H_TO_COUNT		0x24
+#define NWL_DSI_CFG_TWAKEUP			0x28
+#define NWL_DSI_CFG_STATUS_OUT			0x2c
+#define NWL_DSI_RX_ERROR_STATUS			0x30
+
+/* DSI DPI registers */
+#define NWL_DSI_PIXEL_PAYLOAD_SIZE		0x200
+#define NWL_DSI_PIXEL_FIFO_SEND_LEVEL		0x204
+#define NWL_DSI_INTERFACE_COLOR_CODING		0x208
+#define NWL_DSI_PIXEL_FORMAT			0x20c
+#define NWL_DSI_VSYNC_POLARITY			0x210
+#define NWL_DSI_VSYNC_POLARITY_ACTIVE_LOW	0
+#define NWL_DSI_VSYNC_POLARITY_ACTIVE_HIGH	BIT(1)
+
+#define NWL_DSI_HSYNC_POLARITY			0x214
+#define NWL_DSI_HSYNC_POLARITY_ACTIVE_LOW	0
+#define NWL_DSI_HSYNC_POLARITY_ACTIVE_HIGH	BIT(1)
+
+#define NWL_DSI_VIDEO_MODE			0x218
+#define NWL_DSI_HFP				0x21c
+#define NWL_DSI_HBP				0x220
+#define NWL_DSI_HSA				0x224
+#define NWL_DSI_ENABLE_MULT_PKTS		0x228
+#define NWL_DSI_VBP				0x22c
+#define NWL_DSI_VFP				0x230
+#define NWL_DSI_BLLP_MODE			0x234
+#define NWL_DSI_USE_NULL_PKT_BLLP		0x238
+#define NWL_DSI_VACTIVE				0x23c
+#define NWL_DSI_VC				0x240
+
+/* DSI APB PKT control */
+#define NWL_DSI_TX_PAYLOAD			0x280
+#define NWL_DSI_PKT_CONTROL			0x284
+#define NWL_DSI_SEND_PACKET			0x288
+#define NWL_DSI_PKT_STATUS			0x28c
+#define NWL_DSI_PKT_FIFO_WR_LEVEL		0x290
+#define NWL_DSI_PKT_FIFO_RD_LEVEL		0x294
+#define NWL_DSI_RX_PAYLOAD			0x298
+#define NWL_DSI_RX_PKT_HEADER			0x29c
+
+/* DSI IRQ handling */
+#define NWL_DSI_IRQ_STATUS			0x2a0
+#define NWL_DSI_SM_NOT_IDLE			BIT(0)
+#define NWL_DSI_TX_PKT_DONE			BIT(1)
+#define NWL_DSI_DPHY_DIRECTION			BIT(2)
+#define NWL_DSI_TX_FIFO_OVFLW			BIT(3)
+#define NWL_DSI_TX_FIFO_UDFLW			BIT(4)
+#define NWL_DSI_RX_FIFO_OVFLW			BIT(5)
+#define NWL_DSI_RX_FIFO_UDFLW			BIT(6)
+#define NWL_DSI_RX_PKT_HDR_RCVD			BIT(7)
+#define NWL_DSI_RX_PKT_PAYLOAD_DATA_RCVD	BIT(8)
+#define NWL_DSI_BTA_TIMEOUT			BIT(29)
+#define NWL_DSI_LP_RX_TIMEOUT			BIT(30)
+#define NWL_DSI_HS_TX_TIMEOUT			BIT(31)
+
+#define NWL_DSI_IRQ_STATUS2			0x2a4
+#define NWL_DSI_SINGLE_BIT_ECC_ERR		BIT(0)
+#define NWL_DSI_MULTI_BIT_ECC_ERR		BIT(1)
+#define NWL_DSI_CRC_ERR				BIT(2)
+
+#define NWL_DSI_IRQ_MASK			0x2a8
+#define NWL_DSI_SM_NOT_IDLE_MASK		BIT(0)
+#define NWL_DSI_TX_PKT_DONE_MASK		BIT(1)
+#define NWL_DSI_DPHY_DIRECTION_MASK		BIT(2)
+#define NWL_DSI_TX_FIFO_OVFLW_MASK		BIT(3)
+#define NWL_DSI_TX_FIFO_UDFLW_MASK		BIT(4)
+#define NWL_DSI_RX_FIFO_OVFLW_MASK		BIT(5)
+#define NWL_DSI_RX_FIFO_UDFLW_MASK		BIT(6)
+#define NWL_DSI_RX_PKT_HDR_RCVD_MASK		BIT(7)
+#define NWL_DSI_RX_PKT_PAYLOAD_DATA_RCVD_MASK	BIT(8)
+#define NWL_DSI_BTA_TIMEOUT_MASK		BIT(29)
+#define NWL_DSI_LP_RX_TIMEOUT_MASK		BIT(30)
+#define NWL_DSI_HS_TX_TIMEOUT_MASK		BIT(31)
+
+#define NWL_DSI_IRQ_MASK2			0x2ac
+#define NWL_DSI_SINGLE_BIT_ECC_ERR_MASK		BIT(0)
+#define NWL_DSI_MULTI_BIT_ECC_ERR_MASK		BIT(1)
+#define NWL_DSI_CRC_ERR_MASK			BIT(2)
+
+/*
+ * PKT_CONTROL format:
+ * [15: 0] - word count
+ * [17:16] - virtual channel
+ * [23:18] - data type
+ * [24]	   - LP or HS select (0 - LP, 1 - HS)
+ * [25]	   - perform BTA after packet is sent
+ * [26]	   - perform BTA only, no packet tx
+ */
+#define NWL_DSI_WC(x)		FIELD_PREP(GENMASK(15, 0), (x))
+#define NWL_DSI_TX_VC(x)	FIELD_PREP(GENMASK(17, 16), (x))
+#define NWL_DSI_TX_DT(x)	FIELD_PREP(GENMASK(23, 18), (x))
+#define NWL_DSI_HS_SEL(x)	FIELD_PREP(GENMASK(24, 24), (x))
+#define NWL_DSI_BTA_TX(x)	FIELD_PREP(GENMASK(25, 25), (x))
+#define NWL_DSI_BTA_NO_TX(x)	FIELD_PREP(GENMASK(26, 26), (x))
+
+/*
+ * RX_PKT_HEADER format:
+ * [15: 0] - word count
+ * [21:16] - data type
+ * [23:22] - virtual channel
+ */
+#define NWL_DSI_RX_DT(x)	FIELD_GET(GENMASK(21, 16), (x))
+#define NWL_DSI_RX_VC(x)	FIELD_GET(GENMASK(23, 22), (x))
+
+/* DSI Video mode */
+#define NWL_DSI_VM_BURST_MODE_WITH_SYNC_PULSES		0
+#define NWL_DSI_VM_NON_BURST_MODE_WITH_SYNC_EVENTS	BIT(0)
+#define NWL_DSI_VM_BURST_MODE				BIT(1)
+
+/* * DPI color coding */
+#define NWL_DSI_DPI_16_BIT_565_PACKED	0
+#define NWL_DSI_DPI_16_BIT_565_ALIGNED	1
+#define NWL_DSI_DPI_16_BIT_565_SHIFTED	2
+#define NWL_DSI_DPI_18_BIT_PACKED	3

Quoted 156 lines · Guido Günther

This adds initial support for the NWL MIPI DSI Host controller found on i.MX8 SoCs.

It adds support for the i.MX8MQ but the same IP can be found on e.g. the i.MX8QXP.

It has been tested on the Librem 5 devkit using mxsfb.

Signed-off-by Guido Günther <[email protected]>

Co-developed-by Robert Chiras <[email protected]>

Signed-off-by Robert Chiras <[email protected]>

Tested-by Robert Chiras <[email protected]>

---
 drivers/gpu/drm/bridge/Kconfig   |   16 +
 drivers/gpu/drm/bridge/Makefile  |    3 +
 drivers/gpu/drm/bridge/nwl-dsi.c | 1180 ++++++++++++++++++++++++++++++
 drivers/gpu/drm/bridge/nwl-dsi.h |  144 ++++
 4 files changed, 1343 insertions(+)
 create mode 100644 drivers/gpu/drm/bridge/nwl-dsi.c
 create mode 100644 drivers/gpu/drm/bridge/nwl-dsi.h

drivers/gpu/drm/bridge/Kconfig +16 -0

index 1cc9f502c1f2..13021f9a6107 100644
@@ -65,6 +65,22 @@ config DRM_MEGACHIPS_STDPXXXX_GE_B850V3_FW
           to DP++. This is used with the i.MX6 imx-ldb
           driver. You are likely to say N here.
 
+config DRM_NWL_MIPI_DSI
+	tristate "Northwest Logic MIPI DSI Host controller"
+	depends on DRM
+	depends on COMMON_CLK
+	depends on OF && HAS_IOMEM
+	select DRM_KMS_HELPER
+	select DRM_MIPI_DSI
+	select DRM_PANEL_BRIDGE
+	select GENERIC_PHY_MIPI_DPHY
+	select MFD_SYSCON
+	select MULTIPLEXER
+	select REGMAP_MMIO
+	help
+	  This enables the Northwest Logic MIPI DSI Host controller as
+	  for example found on NXP's i.MX8 Processors.
+
 config DRM_NXP_PTN3460
 	tristate "NXP PTN3460 DP/LVDS bridge"
 	depends on OF

drivers/gpu/drm/bridge/Makefile +3 -0

index 4934fcf5a6f8..c3f3a43e9b8f 100644
@@ -16,4 +16,7 @@ obj-$(CONFIG_DRM_ANALOGIX_DP) += analogix/
 obj-$(CONFIG_DRM_I2C_ADV7511) += adv7511/
 obj-$(CONFIG_DRM_TI_SN65DSI86) += ti-sn65dsi86.o
 obj-$(CONFIG_DRM_TI_TFP410) += ti-tfp410.o
+obj-$(CONFIG_DRM_NWL_MIPI_DSI) += nwl-dsi.o
 obj-y += synopsys/
+
+header-test-y += nwl-dsi.h

drivers/gpu/drm/bridge/nwl-dsi.c new file +90 -0

new file mode 100644
index 000000000000..dea5429a1e17
@@ -0,0 +1,1180 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * i.MX8 NWL MIPI DSI host driver
+ *
+ * Copyright (C) 2017 NXP
+ * Copyright (C) 2019 Purism SPC
+ */
+
+#include <linux/bitfield.h>
+#include <linux/clk.h>
+#include <linux/irq.h>
+#include <linux/math64.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/mux/consumer.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/phy/phy.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+#include <linux/sys_soc.h>
+#include <linux/time64.h>
+
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_bridge.h>
+#include <drm/drm_mipi_dsi.h>
+#include <drm/drm_of.h>
+#include <drm/drm_panel.h>
+#include <drm/drm_print.h>
+#include <drm/drm_probe_helper.h>
+
+#include <video/mipi_display.h>
+#include <video/videomode.h>
+
+#include "nwl-dsi.h"
+
+#define DRV_NAME "nwl-dsi"
+
+/* i.MX8 NWL quirks */
+/* i.MX8MQ errata E11418 */
+#define E11418_HS_MODE_QUIRK	BIT(0)
+/* Skip DSI bits in SRC on disable to avoid blank display on enable */
+#define SRC_RESET_QUIRK		BIT(1)
+
+#define NWL_DSI_MIPI_FIFO_TIMEOUT msecs_to_jiffies(500)
+
+enum transfer_direction {
+	DSI_PACKET_SEND,
+	DSI_PACKET_RECEIVE,
+};
+
+/* Possible platform specific clocks */
+#define NWL_DSI_CLK_CORE	    "core"
+#define NWL_DSI_MAX_PLATFORM_CLOCKS 1
+
+struct nwl_dsi_plat_clk_config {
+	const char *id;
+	struct clk *clk;
+	bool present;
+};
+
+struct nwl_dsi_transfer {
+	const struct mipi_dsi_msg *msg;
+	struct mipi_dsi_packet packet;
+	struct completion completed;
+
+	int status; /* status of transmission */
+	enum transfer_direction direction;
+	bool need_bta;
+	u8 cmd;
+	u16 rx_word_count;
+	size_t tx_len; /* in bytes */
+	size_t rx_len; /* in bytes */
+};
+
+struct nwl_dsi {
+	struct drm_bridge bridge;
+	struct mipi_dsi_host dsi_host;
+	struct drm_bridge *panel_bridge;
+	struct device *dev;
+	struct phy *phy;
+	union phy_configure_opts phy_cfg;
+	unsigned int quirks;
+
+	struct regmap *regmap;
+	int irq;
+	struct reset_control *rstc;
+	struct mux_control *mux;
+
+	/* DSI clocks */

drivers/gpu/drm/bridge/nwl-dsi.c line 95

Quoted 5 lines

drivers/gpu/drm/bridge/nwl-dsi.c new file +5 -0

+	struct clk *phy_ref_clk;
+	struct clk *rx_esc_clk;
+	struct clk *tx_esc_clk;
+	/* Platform dependent clocks */
+	struct nwl_dsi_plat_clk_config clk_config[NWL_DSI_MAX_PLATFORM_CLOCKS];

These clocks are not documented.

Quoted 32 lines

drivers/gpu/drm/bridge/nwl-dsi.c new file +30 -0

+
+	/* dsi lanes */
+	u32 lanes;
+	enum mipi_dsi_pixel_format format;
+	struct drm_display_mode mode;
+	unsigned long dsi_mode_flags;
+
+	struct nwl_dsi_transfer *xfer;
+
+	const struct nwl_dsi_platform_data *pdata;
+};
+
+/* Platform specific hooks to enable other SoCs like the i.MX8QM */
+struct nwl_dsi_platform_data {
+	int (*poweron)(struct nwl_dsi *dsi);
+	int (*poweroff)(struct nwl_dsi *dsi);
+	int (*select_input)(struct nwl_dsi *dsi);
+	int (*deselect_input)(struct nwl_dsi *dsi);
+	struct nwl_dsi_plat_clk_config clk_config[NWL_DSI_MAX_PLATFORM_CLOCKS];
+};
+
+static const struct regmap_config nwl_dsi_regmap_config = {
+	.reg_bits = 16,
+	.val_bits = 32,
+	.reg_stride = 4,
+	.max_register = NWL_DSI_IRQ_MASK2,
+	.name = DRV_NAME,
+};
+
+static inline struct nwl_dsi *bridge_to_dsi(struct drm_bridge *bridge)

drivers/gpu/drm/bridge/nwl-dsi.c line 130

Quoted 5 lines

drivers/gpu/drm/bridge/nwl-dsi.c new file +5 -0

+{
+	return container_of(bridge, struct nwl_dsi, bridge);
+}
+
+

spare empty line

Quoted 21 lines

drivers/gpu/drm/bridge/nwl-dsi.c new file +19 -0

+static int nwl_dsi_write(struct nwl_dsi *dsi, unsigned int reg, u32 val)
+{
+	int ret;
+
+	ret = regmap_write(dsi->regmap, reg, val);
+	if (ret < 0)
+		DRM_DEV_ERROR(dsi->dev,
+			      "Failed to write NWL DSI reg 0x%x: %d\n", reg,
+			      ret);
+	return ret;
+}
+
+static u32 nwl_dsi_read(struct nwl_dsi *dsi, u32 reg)
+{
+	unsigned int val;
+	int ret;
+
+	ret = regmap_read(dsi->regmap, reg, &val);
+	if (ret < 0)

drivers/gpu/drm/bridge/nwl-dsi.c line 153

Quoted 4 lines

drivers/gpu/drm/bridge/nwl-dsi.c new file +4 -0

+		DRM_DEV_ERROR(dsi->dev, "Failed to read NWL DSI reg 0x%x: %d\n",
+			      reg, ret);
+
+	return val;

Error is logged, but not propagated, as a result caller will assume the read was successful, quite fishy.

Quoted 12 lines

drivers/gpu/drm/bridge/nwl-dsi.c new file +10 -0

+}
+
+static u32 nwl_dsi_get_dpi_pixel_format(enum mipi_dsi_pixel_format format)
+{
+	switch (format) {
+	case MIPI_DSI_FMT_RGB565:
+		return NWL_DSI_PIXEL_FORMAT_16;
+	case MIPI_DSI_FMT_RGB666:
+		return NWL_DSI_PIXEL_FORMAT_18L;
+	case MIPI_DSI_FMT_RGB666_PACKED:

drivers/gpu/drm/bridge/nwl-dsi.c line 168

Quoted 5 lines

drivers/gpu/drm/bridge/nwl-dsi.c new file +5 -0

+		return NWL_DSI_PIXEL_FORMAT_18;
+	case MIPI_DSI_FMT_RGB888:
+		return NWL_DSI_PIXEL_FORMAT_24;
+	default:
+		return -EINVAL;

return type should be signed

Quoted 101 lines

drivers/gpu/drm/bridge/nwl-dsi.c new file +99 -0

+	}
+}
+
+/*
+ * ps2bc - Picoseconds to byte clock cycles
+ */
+static u32 ps2bc(struct nwl_dsi *dsi, unsigned long long ps)
+{
+	u32 bpp = mipi_dsi_pixel_format_to_bpp(dsi->format);
+
+	return DIV64_U64_ROUND_UP(ps * dsi->mode.clock * bpp,
+				  dsi->lanes * 8 * NSEC_PER_SEC);
+}
+
+/*
+ * ui2bc - UI time periods to byte clock cycles
+ */
+static u32 ui2bc(struct nwl_dsi *dsi, unsigned long long ui)
+{
+	u32 bpp = mipi_dsi_pixel_format_to_bpp(dsi->format);
+
+	return DIV64_U64_ROUND_UP(ui * dsi->lanes,
+				  dsi->mode.clock * 1000 * bpp);
+}
+
+/*
+ * us2bc - micro seconds to lp clock cycles
+ */
+static u32 us2lp(u32 lp_clk_rate, unsigned long us)
+{
+	return DIV_ROUND_UP(us * lp_clk_rate, USEC_PER_SEC);
+}
+
+static int nwl_dsi_config_host(struct nwl_dsi *dsi)
+{
+	u32 cycles;
+	struct phy_configure_opts_mipi_dphy *cfg = &dsi->phy_cfg.mipi_dphy;
+
+	if (dsi->lanes < 1 || dsi->lanes > 4)
+		return -EINVAL;
+
+	DRM_DEV_DEBUG_DRIVER(dsi->dev, "DSI Lanes %d\n", dsi->lanes);
+	nwl_dsi_write(dsi, NWL_DSI_CFG_NUM_LANES, dsi->lanes - 1);
+
+	if (dsi->dsi_mode_flags & MIPI_DSI_CLOCK_NON_CONTINUOUS) {
+		nwl_dsi_write(dsi, NWL_DSI_CFG_NONCONTINUOUS_CLK, 0x01);
+		nwl_dsi_write(dsi, NWL_DSI_CFG_AUTOINSERT_EOTP, 0x01);
+	} else {
+		nwl_dsi_write(dsi, NWL_DSI_CFG_NONCONTINUOUS_CLK, 0x00);
+		nwl_dsi_write(dsi, NWL_DSI_CFG_AUTOINSERT_EOTP, 0x00);
+	}
+
+	/* values in byte clock cycles */
+	cycles = ui2bc(dsi, cfg->clk_pre);
+	DRM_DEV_DEBUG_DRIVER(dsi->dev, "cfg_t_pre: 0x%x\n", cycles);
+	nwl_dsi_write(dsi, NWL_DSI_CFG_T_PRE, cycles);
+	cycles = ps2bc(dsi, cfg->lpx + cfg->clk_prepare + cfg->clk_zero);
+	DRM_DEV_DEBUG_DRIVER(dsi->dev, "cfg_tx_gap (pre): 0x%x\n", cycles);
+	cycles += ui2bc(dsi, cfg->clk_pre);
+	DRM_DEV_DEBUG_DRIVER(dsi->dev, "cfg_t_post: 0x%x\n", cycles);
+	nwl_dsi_write(dsi, NWL_DSI_CFG_T_POST, cycles);
+	cycles = ps2bc(dsi, cfg->hs_exit);
+	DRM_DEV_DEBUG_DRIVER(dsi->dev, "cfg_tx_gap: 0x%x\n", cycles);
+	nwl_dsi_write(dsi, NWL_DSI_CFG_TX_GAP, cycles);
+
+	nwl_dsi_write(dsi, NWL_DSI_CFG_EXTRA_CMDS_AFTER_EOTP, 0x01);
+	nwl_dsi_write(dsi, NWL_DSI_CFG_HTX_TO_COUNT, 0x00);
+	nwl_dsi_write(dsi, NWL_DSI_CFG_LRX_H_TO_COUNT, 0x00);
+	nwl_dsi_write(dsi, NWL_DSI_CFG_BTA_H_TO_COUNT, 0x00);
+	/* In LP clock cycles */
+	cycles = us2lp(cfg->lp_clk_rate, cfg->wakeup);
+	DRM_DEV_DEBUG_DRIVER(dsi->dev, "cfg_twakeup: 0x%x\n", cycles);
+	nwl_dsi_write(dsi, NWL_DSI_CFG_TWAKEUP, cycles);
+
+	return 0;
+}
+
+static int nwl_dsi_config_dpi(struct nwl_dsi *dsi)
+{
+	u32 color_format, mode;
+	bool burst_mode;
+	int hfront_porch, hback_porch, vfront_porch, vback_porch;
+	int hsync_len, vsync_len;
+
+	hfront_porch = dsi->mode.hsync_start - dsi->mode.hdisplay;
+	hsync_len = dsi->mode.hsync_end - dsi->mode.hsync_start;
+	hback_porch = dsi->mode.htotal - dsi->mode.hsync_end;
+
+	vfront_porch = dsi->mode.vsync_start - dsi->mode.vdisplay;
+	vsync_len = dsi->mode.vsync_end - dsi->mode.vsync_start;
+	vback_porch = dsi->mode.vtotal - dsi->mode.vsync_end;
+
+	DRM_DEV_DEBUG_DRIVER(dsi->dev, "hfront_porch = %d\n", hfront_porch);
+	DRM_DEV_DEBUG_DRIVER(dsi->dev, "hback_porch = %d\n", hback_porch);
+	DRM_DEV_DEBUG_DRIVER(dsi->dev, "hsync_len = %d\n", hsync_len);
+	DRM_DEV_DEBUG_DRIVER(dsi->dev, "hdisplay = %d\n", dsi->mode.hdisplay);
+	DRM_DEV_DEBUG_DRIVER(dsi->dev, "vfront_porch = %d\n", vfront_porch);
+	DRM_DEV_DEBUG_DRIVER(dsi->dev, "vback_porch = %d\n", vback_porch);
+	DRM_DEV_DEBUG_DRIVER(dsi->dev, "vsync_len = %d\n", vsync_len);

drivers/gpu/drm/bridge/nwl-dsi.c line 272

Quoted 5 lines

drivers/gpu/drm/bridge/nwl-dsi.c new file +5 -0

+	DRM_DEV_DEBUG_DRIVER(dsi->dev, "vactive = %d\n", dsi->mode.vdisplay);
+	DRM_DEV_DEBUG_DRIVER(dsi->dev, "clock = %d kHz\n", dsi->mode.clock);
+
+	color_format = nwl_dsi_get_dpi_pixel_format(dsi->format);
+	if (color_format < 0) {

As robot mentioned  it is always false.

Quoted 44 lines

drivers/gpu/drm/bridge/nwl-dsi.c new file +42 -0

+		DRM_DEV_ERROR(dsi->dev, "Invalid color format 0x%x\n",
+			      dsi->format);
+		return color_format;
+	}
+	DRM_DEV_DEBUG_DRIVER(dsi->dev, "pixel fmt = %d\n", dsi->format);
+
+	nwl_dsi_write(dsi, NWL_DSI_INTERFACE_COLOR_CODING, NWL_DSI_DPI_24_BIT);
+	nwl_dsi_write(dsi, NWL_DSI_PIXEL_FORMAT, color_format);
+	/*
+	 * Adjusting input polarity based on the video mode results in
+	 * a black screen so always pick active low:
+	 */
+	nwl_dsi_write(dsi, NWL_DSI_VSYNC_POLARITY,
+		      NWL_DSI_VSYNC_POLARITY_ACTIVE_LOW);
+	nwl_dsi_write(dsi, NWL_DSI_HSYNC_POLARITY,
+		      NWL_DSI_HSYNC_POLARITY_ACTIVE_LOW);
+
+	burst_mode = (dsi->dsi_mode_flags & MIPI_DSI_MODE_VIDEO_BURST) &&
+		     !(dsi->dsi_mode_flags & MIPI_DSI_MODE_VIDEO_SYNC_PULSE);
+
+	if (burst_mode) {
+		nwl_dsi_write(dsi, NWL_DSI_VIDEO_MODE, NWL_DSI_VM_BURST_MODE);
+		nwl_dsi_write(dsi, NWL_DSI_PIXEL_FIFO_SEND_LEVEL, 256);
+	} else {
+		mode = ((dsi->dsi_mode_flags & MIPI_DSI_MODE_VIDEO_SYNC_PULSE) ?
+				NWL_DSI_VM_BURST_MODE_WITH_SYNC_PULSES :
+				NWL_DSI_VM_NON_BURST_MODE_WITH_SYNC_EVENTS);
+		nwl_dsi_write(dsi, NWL_DSI_VIDEO_MODE, mode);
+		nwl_dsi_write(dsi, NWL_DSI_PIXEL_FIFO_SEND_LEVEL,
+			      dsi->mode.hdisplay);
+	}
+
+	nwl_dsi_write(dsi, NWL_DSI_HFP, hfront_porch);
+	nwl_dsi_write(dsi, NWL_DSI_HBP, hback_porch);
+	nwl_dsi_write(dsi, NWL_DSI_HSA, hsync_len);
+
+	nwl_dsi_write(dsi, NWL_DSI_ENABLE_MULT_PKTS, 0x0);
+	nwl_dsi_write(dsi, NWL_DSI_BLLP_MODE, 0x1);
+	nwl_dsi_write(dsi, NWL_DSI_USE_NULL_PKT_BLLP, 0x0);
+	nwl_dsi_write(dsi, NWL_DSI_VC, 0x0);
+
+	nwl_dsi_write(dsi, NWL_DSI_PIXEL_PAYLOAD_SIZE, dsi->mode.hdisplay);

drivers/gpu/drm/bridge/nwl-dsi.c line 317

Quoted 3 lines

drivers/gpu/drm/bridge/nwl-dsi.c new file +3 -0

+	nwl_dsi_write(dsi, NWL_DSI_VACTIVE, dsi->mode.vdisplay - 1);
+	nwl_dsi_write(dsi, NWL_DSI_VBP, vback_porch);
+	nwl_dsi_write(dsi, NWL_DSI_VFP, vfront_porch);

No checks for results of nwl_dsi_write. You should either add check after every call, or try "error state" pattern (see for example for tc358764.c driver).

Quoted 12 lines

drivers/gpu/drm/bridge/nwl-dsi.c new file +10 -0

+
+	return 0;
+}
+
+static void nwl_dsi_init_interrupts(struct nwl_dsi *dsi)
+{
+	u32 irq_enable;
+
+	nwl_dsi_write(dsi, NWL_DSI_IRQ_MASK, 0xffffffff);
+	nwl_dsi_write(dsi, NWL_DSI_IRQ_MASK2, 0x7);

drivers/gpu/drm/bridge/nwl-dsi.c line 332

Quoted 5 lines

drivers/gpu/drm/bridge/nwl-dsi.c new file +5 -0

+
+	irq_enable = ~(u32)(NWL_DSI_TX_PKT_DONE_MASK |
+			    NWL_DSI_RX_PKT_HDR_RCVD_MASK |
+			    NWL_DSI_TX_FIFO_OVFLW_MASK |
+			    NWL_DSI_HS_TX_TIMEOUT_MASK);

I wonder if lack of '(u32)' would lead to some bugs/warnings.

Quoted 8 lines

drivers/gpu/drm/bridge/nwl-dsi.c new file +8 -0

+
+	nwl_dsi_write(dsi, NWL_DSI_IRQ_MASK, irq_enable);
+}
+
+static int nwl_dsi_host_attach(struct mipi_dsi_host *dsi_host,
+			       struct mipi_dsi_device *device)
+{
+	struct nwl_dsi *dsi = container_of(dsi_host, struct nwl_dsi, dsi_host);

drivers/gpu/drm/bridge/nwl-dsi.c line 350

Quoted 10 lines

drivers/gpu/drm/bridge/nwl-dsi.c new file +10 -0

+	struct device *dev = dsi->dev;
+	struct drm_bridge *bridge;
+	struct drm_panel *panel;
+	int ret;
+
+	DRM_DEV_INFO(dev, "lanes=%u, format=0x%x flags=0x%lx\n", device->lanes,
+		     device->format, device->mode_flags);
+
+	if (device->lanes < 1 || device->lanes > 4)
+		return -EINVAL;

I guess this sanity check should be rather in mipi_dsi_attach, but since it is not there let's leave it here.

Quoted 363 lines

drivers/gpu/drm/bridge/nwl-dsi.c new file +363 -0

+
+	dsi->lanes = device->lanes;
+	dsi->format = device->format;
+	dsi->dsi_mode_flags = device->mode_flags;
+
+	ret = drm_of_find_panel_or_bridge(dsi->dev->of_node, 1, 0, &panel,
+					  &bridge);
+	if (ret)
+		return ret;
+
+	if (panel) {
+		bridge = drm_panel_bridge_add(panel, DRM_MODE_CONNECTOR_DSI);
+		if (IS_ERR(bridge))
+			return PTR_ERR(bridge);
+	}
+
+	dsi->panel_bridge = bridge;
+	drm_bridge_add(&dsi->bridge);
+
+	return 0;
+}
+
+static int nwl_dsi_host_detach(struct mipi_dsi_host *dsi_host,
+			       struct mipi_dsi_device *device)
+{
+	struct nwl_dsi *dsi = container_of(dsi_host, struct nwl_dsi, dsi_host);
+
+	drm_of_panel_bridge_remove(dsi->dev->of_node, 1, 0);
+	drm_bridge_remove(&dsi->bridge);
+
+	return 0;
+}
+
+static bool nwl_dsi_read_packet(struct nwl_dsi *dsi, u32 status)
+{
+	struct device *dev = dsi->dev;
+	struct nwl_dsi_transfer *xfer = dsi->xfer;
+	u8 *payload = xfer->msg->rx_buf;
+	u32 val;
+	u16 word_count;
+	u8 channel;
+	u8 data_type;
+
+	xfer->status = 0;
+
+	if (xfer->rx_word_count == 0) {
+		if (!(status & NWL_DSI_RX_PKT_HDR_RCVD))
+			return false;
+		/* Get the RX header and parse it */
+		val = nwl_dsi_read(dsi, NWL_DSI_RX_PKT_HEADER);
+		word_count = NWL_DSI_WC(val);
+		channel = NWL_DSI_RX_VC(val);
+		data_type = NWL_DSI_RX_DT(val);
+
+		if (channel != xfer->msg->channel) {
+			DRM_DEV_ERROR(dev,
+				      "[%02X] Channel mismatch (%u != %u)\n",
+				      xfer->cmd, channel, xfer->msg->channel);
+			return true;
+		}
+
+		switch (data_type) {
+		case MIPI_DSI_RX_GENERIC_SHORT_READ_RESPONSE_2BYTE:
+			/* Fall through */
+		case MIPI_DSI_RX_DCS_SHORT_READ_RESPONSE_2BYTE:
+			if (xfer->msg->rx_len > 1) {
+				/* read second byte */
+				payload[1] = word_count >> 8;
+				++xfer->rx_len;
+			}
+			/* Fall through */
+		case MIPI_DSI_RX_GENERIC_SHORT_READ_RESPONSE_1BYTE:
+			/* Fall through */
+		case MIPI_DSI_RX_DCS_SHORT_READ_RESPONSE_1BYTE:
+			if (xfer->msg->rx_len > 0) {
+				/* read first byte */
+				payload[0] = word_count & 0xff;
+				++xfer->rx_len;
+			}
+			xfer->status = xfer->rx_len;
+			return true;
+		case MIPI_DSI_RX_ACKNOWLEDGE_AND_ERROR_REPORT:
+			word_count &= 0xff;
+			DRM_DEV_ERROR(dev, "[%02X] DSI error report: 0x%02x\n",
+				      xfer->cmd, word_count);
+			xfer->status = -EPROTO;
+			return true;
+		}
+
+		if (word_count > xfer->msg->rx_len) {
+			DRM_DEV_ERROR(
+				dev,
+				"[%02X] Receive buffer too small: %zu (< %u)\n",
+				xfer->cmd, xfer->msg->rx_len, word_count);
+			return true;
+		}
+
+		xfer->rx_word_count = word_count;
+	} else {
+		/* Set word_count from previous header read */
+		word_count = xfer->rx_word_count;
+	}
+
+	/* If RX payload is not yet received, wait for it */
+	if (!(status & NWL_DSI_RX_PKT_PAYLOAD_DATA_RCVD))
+		return false;
+
+	/* Read the RX payload */
+	while (word_count >= 4) {
+		val = nwl_dsi_read(dsi, NWL_DSI_RX_PAYLOAD);
+		payload[0] = (val >> 0) & 0xff;
+		payload[1] = (val >> 8) & 0xff;
+		payload[2] = (val >> 16) & 0xff;
+		payload[3] = (val >> 24) & 0xff;
+		payload += 4;
+		xfer->rx_len += 4;
+		word_count -= 4;
+	}
+
+	if (word_count > 0) {
+		val = nwl_dsi_read(dsi, NWL_DSI_RX_PAYLOAD);
+		switch (word_count) {
+		case 3:
+			payload[2] = (val >> 16) & 0xff;
+			++xfer->rx_len;
+			/* Fall through */
+		case 2:
+			payload[1] = (val >> 8) & 0xff;
+			++xfer->rx_len;
+			/* Fall through */
+		case 1:
+			payload[0] = (val >> 0) & 0xff;
+			++xfer->rx_len;
+			break;
+		}
+	}
+
+	xfer->status = xfer->rx_len;
+
+	return true;
+}
+
+static void nwl_dsi_finish_transmission(struct nwl_dsi *dsi, u32 status)
+{
+	struct nwl_dsi_transfer *xfer = dsi->xfer;
+	bool end_packet = false;
+
+	if (!xfer)
+		return;
+
+	if (xfer->direction == DSI_PACKET_SEND &&
+	    status & NWL_DSI_TX_PKT_DONE) {
+		xfer->status = xfer->tx_len;
+		end_packet = true;
+	} else if (status & NWL_DSI_DPHY_DIRECTION &&
+		   ((status & (NWL_DSI_RX_PKT_HDR_RCVD |
+			       NWL_DSI_RX_PKT_PAYLOAD_DATA_RCVD)))) {
+		end_packet = nwl_dsi_read_packet(dsi, status);
+	}
+
+	if (end_packet)
+		complete(&xfer->completed);
+}
+
+static void nwl_dsi_begin_transmission(struct nwl_dsi *dsi)
+{
+	struct nwl_dsi_transfer *xfer = dsi->xfer;
+	struct mipi_dsi_packet *pkt = &xfer->packet;
+	const u8 *payload;
+	size_t length;
+	u16 word_count;
+	u8 hs_mode;
+	u32 val;
+	u32 hs_workaround = 0;
+
+	/* Send the payload, if any */
+	length = pkt->payload_length;
+	payload = pkt->payload;
+
+	while (length >= 4) {
+		val = *(u32 *)payload;
+		hs_workaround |= !(val & 0xFFFF00);
+		nwl_dsi_write(dsi, NWL_DSI_TX_PAYLOAD, val);
+		payload += 4;
+		length -= 4;
+	}
+	/* Send the rest of the payload */
+	val = 0;
+	switch (length) {
+	case 3:
+		val |= payload[2] << 16;
+		/* Fall through */
+	case 2:
+		val |= payload[1] << 8;
+		hs_workaround |= !(val & 0xFFFF00);
+		/* Fall through */
+	case 1:
+		val |= payload[0];
+		nwl_dsi_write(dsi, NWL_DSI_TX_PAYLOAD, val);
+		break;
+	}
+	xfer->tx_len = pkt->payload_length;
+
+	/*
+	 * Send the header
+	 * header[0] = Virtual Channel + Data Type
+	 * header[1] = Word Count LSB (LP) or first param (SP)
+	 * header[2] = Word Count MSB (LP) or second param (SP)
+	 */
+	word_count = pkt->header[1] | (pkt->header[2] << 8);
+	if (hs_workaround && (dsi->quirks & E11418_HS_MODE_QUIRK)) {
+		DRM_DEV_DEBUG_DRIVER(dsi->dev,
+				     "Using hs mode workaround for cmd 0x%x\n",
+				     xfer->cmd);
+		hs_mode = 1;
+	} else {
+		hs_mode = (xfer->msg->flags & MIPI_DSI_MSG_USE_LPM) ? 0 : 1;
+	}
+	val = NWL_DSI_WC(word_count) | NWL_DSI_TX_VC(xfer->msg->channel) |
+	      NWL_DSI_TX_DT(xfer->msg->type) | NWL_DSI_HS_SEL(hs_mode) |
+	      NWL_DSI_BTA_TX(xfer->need_bta);
+	nwl_dsi_write(dsi, NWL_DSI_PKT_CONTROL, val);
+
+	/* Send packet command */
+	nwl_dsi_write(dsi, NWL_DSI_SEND_PACKET, 0x1);
+}
+
+static ssize_t nwl_dsi_host_transfer(struct mipi_dsi_host *dsi_host,
+				     const struct mipi_dsi_msg *msg)
+{
+	struct nwl_dsi *dsi = container_of(dsi_host, struct nwl_dsi, dsi_host);
+	struct nwl_dsi_transfer xfer;
+	ssize_t ret = 0;
+
+	/* Create packet to be sent */
+	dsi->xfer = &xfer;
+	ret = mipi_dsi_create_packet(&xfer.packet, msg);
+	if (ret < 0) {
+		dsi->xfer = NULL;
+		return ret;
+	}
+
+	if ((msg->type & MIPI_DSI_GENERIC_READ_REQUEST_0_PARAM ||
+	     msg->type & MIPI_DSI_GENERIC_READ_REQUEST_1_PARAM ||
+	     msg->type & MIPI_DSI_GENERIC_READ_REQUEST_2_PARAM ||
+	     msg->type & MIPI_DSI_DCS_READ) &&
+	    msg->rx_len > 0 && msg->rx_buf != NULL)
+		xfer.direction = DSI_PACKET_RECEIVE;
+	else
+		xfer.direction = DSI_PACKET_SEND;
+
+	xfer.need_bta = (xfer.direction == DSI_PACKET_RECEIVE);
+	xfer.need_bta |= (msg->flags & MIPI_DSI_MSG_REQ_ACK) ? 1 : 0;
+	xfer.msg = msg;
+	xfer.status = -ETIMEDOUT;
+	xfer.rx_word_count = 0;
+	xfer.rx_len = 0;
+	xfer.cmd = 0x00;
+	if (msg->tx_len > 0)
+		xfer.cmd = ((u8 *)(msg->tx_buf))[0];
+	init_completion(&xfer.completed);
+
+	ret = clk_prepare_enable(dsi->rx_esc_clk);
+	if (ret < 0) {
+		DRM_DEV_ERROR(dsi->dev, "Failed to enable rx_esc clk: %zd\n",
+			      ret);
+		return ret;
+	}
+	DRM_DEV_DEBUG_DRIVER(dsi->dev, "Enabled rx_esc clk @%lu Hz\n",
+			     clk_get_rate(dsi->rx_esc_clk));
+
+	/* Initiate the DSI packet transmision */
+	nwl_dsi_begin_transmission(dsi);
+
+	if (!wait_for_completion_timeout(&xfer.completed,
+					 NWL_DSI_MIPI_FIFO_TIMEOUT)) {
+		DRM_DEV_ERROR(dsi_host->dev, "[%02X] DSI transfer timed out\n",
+			      xfer.cmd);
+		ret = -ETIMEDOUT;
+	} else {
+		ret = xfer.status;
+	}
+
+	clk_disable_unprepare(dsi->rx_esc_clk);
+
+	return ret;
+}
+
+static const struct mipi_dsi_host_ops nwl_dsi_host_ops = {
+	.attach = nwl_dsi_host_attach,
+	.detach = nwl_dsi_host_detach,
+	.transfer = nwl_dsi_host_transfer,
+};
+
+static irqreturn_t nwl_dsi_irq_handler(int irq, void *data)
+{
+	u32 irq_status;
+	struct nwl_dsi *dsi = data;
+
+	irq_status = nwl_dsi_read(dsi, NWL_DSI_IRQ_STATUS);
+
+	if (irq_status & NWL_DSI_TX_FIFO_OVFLW)
+		DRM_DEV_ERROR_RATELIMITED(dsi->dev, "tx fifo overflow\n");
+
+	if (irq_status & NWL_DSI_HS_TX_TIMEOUT)
+		DRM_DEV_ERROR_RATELIMITED(dsi->dev, "HS tx timeout\n");
+
+	if (irq_status & NWL_DSI_TX_PKT_DONE ||
+	    irq_status & NWL_DSI_RX_PKT_HDR_RCVD ||
+	    irq_status & NWL_DSI_RX_PKT_PAYLOAD_DATA_RCVD)
+		nwl_dsi_finish_transmission(dsi, irq_status);
+
+	return IRQ_HANDLED;
+}
+
+static int nwl_dsi_enable(struct nwl_dsi *dsi)
+{
+	struct device *dev = dsi->dev;
+	union phy_configure_opts *phy_cfg = &dsi->phy_cfg;
+	int ret;
+
+	if (!dsi->lanes) {
+		DRM_DEV_ERROR(dev, "Need DSI lanes: %d\n", dsi->lanes);
+		return -EINVAL;
+	}
+
+	ret = phy_init(dsi->phy);
+	if (ret < 0) {
+		DRM_DEV_ERROR(dev, "Failed to init DSI phy: %d\n", ret);
+		return ret;
+	}
+
+	ret = phy_configure(dsi->phy, phy_cfg);
+	if (ret < 0) {
+		DRM_DEV_ERROR(dev, "Failed to configure DSI phy: %d\n", ret);
+		return ret;
+	}
+
+	ret = clk_prepare_enable(dsi->tx_esc_clk);
+	if (ret < 0) {
+		DRM_DEV_ERROR(dsi->dev, "Failed to enable tx_esc clk: %d\n",
+			      ret);
+		return ret;
+	}
+	DRM_DEV_DEBUG_DRIVER(dsi->dev, "Enabled tx_esc clk @%lu Hz\n",
+			     clk_get_rate(dsi->tx_esc_clk));
+
+	ret = nwl_dsi_config_host(dsi);
+	if (ret < 0) {
+		DRM_DEV_ERROR(dev, "Failed to set up DSI: %d", ret);
+		return ret;
+	}
+
+	ret = nwl_dsi_config_dpi(dsi);
+	if (ret < 0) {
+		DRM_DEV_ERROR(dev, "Failed to set up DPI: %d", ret);
+		return ret;
+	}
+
+	ret = phy_power_on(dsi->phy);
+	if (ret < 0) {
+		DRM_DEV_ERROR(dev, "Failed to power on DPHY (%d)\n", ret);
+		return ret;

drivers/gpu/drm/bridge/nwl-dsi.c line 718

Quoted 5 lines

drivers/gpu/drm/bridge/nwl-dsi.c new file +5 -0

+	}
+
+	nwl_dsi_init_interrupts(dsi);
+
+	return 0;

no unwinding in case of error

Quoted 183 lines

drivers/gpu/drm/bridge/nwl-dsi.c new file +183 -0

+}
+
+static int nwl_dsi_disable(struct nwl_dsi *dsi)
+{
+	struct device *dev = dsi->dev;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "Disabling clocks and phy\n");
+
+	phy_power_off(dsi->phy);
+	phy_exit(dsi->phy);
+
+	/* Disabling the clock before the phy breaks enabling dsi again */
+	clk_disable_unprepare(dsi->tx_esc_clk);
+
+	return 0;
+}
+
+static int nwl_dsi_set_platform_clocks(struct nwl_dsi *dsi, bool enable)
+{
+	struct device *dev = dsi->dev;
+	const char *id;
+	struct clk *clk;
+	size_t i;
+	unsigned long rate;
+	int ret, result = 0;
+
+	DRM_DEV_DEBUG_DRIVER(dev, "%s platform clocks\n",
+			     enable ? "enabling" : "disabling");
+	for (i = 0; i < ARRAY_SIZE(dsi->pdata->clk_config); i++) {
+		if (!dsi->clk_config[i].present)
+			continue;
+		id = dsi->clk_config[i].id;
+		clk = dsi->clk_config[i].clk;
+
+		if (enable) {
+			ret = clk_prepare_enable(clk);
+			if (ret < 0) {
+				DRM_DEV_ERROR(dev,
+					      "Failed to enable %s clk: %d\n",
+					      id, ret);
+				result = result ?: ret;
+			}
+			rate = clk_get_rate(clk);
+			DRM_DEV_DEBUG_DRIVER(dev, "Enabled %s clk @%lu Hz\n",
+					     id, rate);
+		} else {
+			clk_disable_unprepare(clk);
+			DRM_DEV_DEBUG_DRIVER(dev, "Disabled %s clk\n", id);
+		}
+	}
+
+	return result;
+}
+
+static int nwl_dsi_plat_enable(struct nwl_dsi *dsi)
+{
+	struct device *dev = dsi->dev;
+	int ret;
+
+	if (dsi->pdata->select_input)
+		dsi->pdata->select_input(dsi);
+
+	ret = nwl_dsi_set_platform_clocks(dsi, true);
+	if (ret < 0)
+		return ret;
+
+	ret = dsi->pdata->poweron(dsi);
+	if (ret < 0)
+		DRM_DEV_ERROR(dev, "Failed to power on DSI: %d\n", ret);
+	return ret;
+}
+
+static void nwl_dsi_plat_disable(struct nwl_dsi *dsi)
+{
+	dsi->pdata->poweroff(dsi);
+	nwl_dsi_set_platform_clocks(dsi, false);
+	if (dsi->pdata->deselect_input)
+		dsi->pdata->deselect_input(dsi);
+}
+
+static void nwl_dsi_bridge_disable(struct drm_bridge *bridge)
+{
+	struct nwl_dsi *dsi = bridge_to_dsi(bridge);
+
+	nwl_dsi_disable(dsi);
+	nwl_dsi_plat_disable(dsi);
+	pm_runtime_put(dsi->dev);
+}
+
+static int nwl_dsi_get_dphy_params(struct nwl_dsi *dsi,
+				   const struct drm_display_mode *mode,
+				   union phy_configure_opts *phy_opts)
+{
+	unsigned long rate;
+	int ret;
+
+	if (dsi->lanes < 1 || dsi->lanes > 4)
+		return -EINVAL;
+
+	/*
+	 * So far the DPHY spec minimal timings work for both mixel
+	 * dphy and nwl dsi host
+	 */
+	ret = phy_mipi_dphy_get_default_config(
+		mode->crtc_clock * 1000,
+		mipi_dsi_pixel_format_to_bpp(dsi->format), dsi->lanes,
+		&phy_opts->mipi_dphy);
+	if (ret < 0)
+		return ret;
+
+	rate = clk_get_rate(dsi->tx_esc_clk);
+	DRM_DEV_DEBUG_DRIVER(dsi->dev, "LP clk is @%lu Hz\n", rate);
+	phy_opts->mipi_dphy.lp_clk_rate = rate;
+
+	return 0;
+}
+
+static bool nwl_dsi_bridge_mode_fixup(struct drm_bridge *bridge,
+				      const struct drm_display_mode *mode,
+				      struct drm_display_mode *adjusted_mode)
+{
+	/* At least LCDIF + NWL needs active high sync */
+	adjusted_mode->flags |= (DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC);
+	adjusted_mode->flags &= ~(DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC);
+
+	return true;
+}
+
+static enum drm_mode_status
+nwl_dsi_bridge_mode_valid(struct drm_bridge *bridge,
+			  const struct drm_display_mode *mode)
+{
+	struct nwl_dsi *dsi = bridge_to_dsi(bridge);
+	int bpp = mipi_dsi_pixel_format_to_bpp(dsi->format);
+
+	if (mode->clock * bpp > 15000000 * dsi->lanes)
+		return MODE_CLOCK_HIGH;
+
+	if (mode->clock * bpp < 80000 * dsi->lanes)
+		return MODE_CLOCK_LOW;
+
+	return MODE_OK;
+}
+
+static void
+nwl_dsi_bridge_mode_set(struct drm_bridge *bridge,
+			const struct drm_display_mode *mode,
+			const struct drm_display_mode *adjusted_mode)
+{
+	struct nwl_dsi *dsi = bridge_to_dsi(bridge);
+	struct device *dev = dsi->dev;
+	union phy_configure_opts new_cfg;
+	unsigned long phy_ref_rate;
+	int ret;
+
+	ret = nwl_dsi_get_dphy_params(dsi, adjusted_mode, &new_cfg);
+	if (ret < 0)
+		return;
+
+	/*
+	 * If hs clock is unchanged, we're all good - all parameters are
+	 * derived from it atm.
+	 */
+	if (new_cfg.mipi_dphy.hs_clk_rate == dsi->phy_cfg.mipi_dphy.hs_clk_rate)
+		return;
+
+	phy_ref_rate = clk_get_rate(dsi->phy_ref_clk);
+	DRM_DEV_DEBUG_DRIVER(dev, "PHY at ref rate: %lu\n", phy_ref_rate);
+	/* Save the new desired phy config */
+	memcpy(&dsi->phy_cfg, &new_cfg, sizeof(new_cfg));
+
+	memcpy(&dsi->mode, adjusted_mode, sizeof(dsi->mode));
+	drm_mode_debug_printmodeline(adjusted_mode);
+}
+
+static void nwl_dsi_bridge_pre_enable(struct drm_bridge *bridge)
+{
+	struct nwl_dsi *dsi = bridge_to_dsi(bridge);
+
+	pm_runtime_get_sync(dsi->dev);
+	nwl_dsi_plat_enable(dsi);
+	nwl_dsi_enable(dsi);
+}

drivers/gpu/drm/bridge/nwl-dsi.c line 905

Quoted 4 lines

drivers/gpu/drm/bridge/nwl-dsi.c new file +4 -0

+
+static int nwl_dsi_bridge_attach(struct drm_bridge *bridge)
+{
+	struct nwl_dsi *dsi = bridge->driver_private;

Please use container_of here, driver_private shouldn't be used in embeded bridges.

Quoted 41 lines

drivers/gpu/drm/bridge/nwl-dsi.c new file +39 -0

+
+	return drm_bridge_attach(bridge->encoder, dsi->panel_bridge, bridge);
+}
+
+static const struct drm_bridge_funcs nwl_dsi_bridge_funcs = {
+	.pre_enable = nwl_dsi_bridge_pre_enable,
+	.disable    = nwl_dsi_bridge_disable,
+	.mode_fixup = nwl_dsi_bridge_mode_fixup,
+	.mode_set   = nwl_dsi_bridge_mode_set,
+	.mode_valid = nwl_dsi_bridge_mode_valid,
+	.attach	    = nwl_dsi_bridge_attach,
+};
+
+static int nwl_dsi_parse_dt(struct nwl_dsi *dsi)
+{
+	struct platform_device *pdev = to_platform_device(dsi->dev);
+	struct clk *clk;
+	const char *clk_id;
+	void __iomem *base;
+	int i, ret;
+
+	dsi->phy = devm_phy_get(dsi->dev, "dphy");
+	if (IS_ERR(dsi->phy)) {
+		ret = PTR_ERR(dsi->phy);
+		if (ret != -EPROBE_DEFER)
+			DRM_DEV_ERROR(dsi->dev, "Could not get PHY: %d\n", ret);
+		return ret;
+	}
+
+	/* Platform dependent clocks */
+	memcpy(dsi->clk_config, dsi->pdata->clk_config,
+	       sizeof(dsi->pdata->clk_config));
+
+	for (i = 0; i < ARRAY_SIZE(dsi->pdata->clk_config); i++) {
+		if (!dsi->clk_config[i].present)
+			continue;
+
+		clk_id = dsi->clk_config[i].id;
+		clk = devm_clk_get(dsi->dev, clk_id);

drivers/gpu/drm/bridge/nwl-dsi.c line 954

Quoted 10 lines

drivers/gpu/drm/bridge/nwl-dsi.c new file +10 -0

+		if (IS_ERR(clk)) {
+			ret = PTR_ERR(clk);
+			DRM_DEV_ERROR(dsi->dev, "Failed to get %s clock: %d\n",
+				      clk_id, ret);
+			return ret;
+		}
+		DRM_DEV_DEBUG_DRIVER(dsi->dev, "Setup clk %s (rate: %lu)\n",
+				     clk_id, clk_get_rate(clk));
+		dsi->clk_config[i].clk = clk;
+	}

As I said earlier this is undocumented.

Quoted 58 lines

drivers/gpu/drm/bridge/nwl-dsi.c new file +58 -0

+
+	/* DSI clocks */
+	clk = devm_clk_get(dsi->dev, "phy_ref");
+	if (IS_ERR(clk)) {
+		ret = PTR_ERR(clk);
+		DRM_DEV_ERROR(dsi->dev, "Failed to get phy_ref clock: %d\n",
+			      ret);
+		return ret;
+	}
+	dsi->phy_ref_clk = clk;
+
+	clk = devm_clk_get(dsi->dev, "rx_esc");
+	if (IS_ERR(clk)) {
+		ret = PTR_ERR(clk);
+		DRM_DEV_ERROR(dsi->dev, "Failed to get rx_esc clock: %d\n",
+			      ret);
+		return ret;
+	}
+	dsi->rx_esc_clk = clk;
+
+	clk = devm_clk_get(dsi->dev, "tx_esc");
+	if (IS_ERR(clk)) {
+		ret = PTR_ERR(clk);
+		DRM_DEV_ERROR(dsi->dev, "Failed to get tx_esc clock: %d\n",
+			      ret);
+		return ret;
+	}
+	dsi->tx_esc_clk = clk;
+
+	dsi->mux = devm_mux_control_get(dsi->dev, NULL);
+	if (IS_ERR(dsi->mux)) {
+		ret = PTR_ERR(dsi->mux);
+		if (ret != -EPROBE_DEFER)
+			DRM_DEV_ERROR(dsi->dev, "Failed to get mux: %d\n", ret);
+		return ret;
+	}
+
+	base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(base))
+		return PTR_ERR(base);
+
+	dsi->regmap =
+		devm_regmap_init_mmio(dsi->dev, base, &nwl_dsi_regmap_config);
+	if (IS_ERR(dsi->regmap)) {
+		ret = PTR_ERR(dsi->regmap);
+		DRM_DEV_ERROR(dsi->dev, "Failed to create NWL DSI regmap: %d\n",
+			      ret);
+		return ret;
+	}
+
+	dsi->irq = platform_get_irq(pdev, 0);
+	if (dsi->irq < 0) {
+		DRM_DEV_ERROR(dsi->dev, "Failed to get device IRQ: %d\n",
+			      dsi->irq);
+		return dsi->irq;
+	}
+
+	dsi->rstc = devm_reset_control_array_get(dsi->dev, false, true);

drivers/gpu/drm/bridge/nwl-dsi.c line 1017

Quoted 5 lines

drivers/gpu/drm/bridge/nwl-dsi.c new file +5 -0

+	if (IS_ERR(dsi->rstc)) {
+		DRM_DEV_ERROR(dsi->dev, "Failed to get resets: %ld\n",
+			      PTR_ERR(dsi->rstc));
+		return PTR_ERR(dsi->rstc);
+	}

You should not error log in case of EPROBE_DEFER.

Quoted 5 lines

drivers/gpu/drm/bridge/nwl-dsi.c new file +3 -0

+
+	return 0;
+}

drivers/gpu/drm/bridge/nwl-dsi.c line 1030

Quoted 10 lines

drivers/gpu/drm/bridge/nwl-dsi.c new file +10 -0

+
+static int imx8mq_dsi_select_input(struct nwl_dsi *dsi)
+{
+	struct device_node *remote;
+	u32 use_dcss = 1;
+	int ret;
+
+	remote = of_graph_get_remote_node(dsi->dev->of_node, 0, 0);
+	if (strcmp(remote->name, "lcdif") == 0)
+		use_dcss = 0;

Checking name of remote note does not look correct, you should check only props from your node.

If the ip has separate lines for DCSS and LCDIF you should distinguish by port number. If they are shared

you can use endpoint number to specify DCSS or LCDIF, in both cases bindings should be adjusted.

Regards

Andrzej

Quoted 290 lines

drivers/gpu/drm/bridge/nwl-dsi.c new file +150 -0

+
+	DRM_DEV_INFO(dsi->dev, "Using %s as input source\n",
+		     (use_dcss) ? "DCSS" : "LCDIF");
+
+	ret = mux_control_try_select(dsi->mux, use_dcss);
+	if (ret < 0)
+		DRM_DEV_ERROR(dsi->dev, "Failed to select input: %d\n", ret);
+
+	of_node_put(remote);
+	return ret;
+}
+
+
+static int imx8mq_dsi_deselect_input(struct nwl_dsi *dsi)
+{
+	int ret;
+
+	ret = mux_control_deselect(dsi->mux);
+	if (ret < 0)
+		DRM_DEV_ERROR(dsi->dev, "Failed to deselect input: %d\n", ret);
+
+	return ret;
+}
+
+
+static int imx8mq_dsi_poweron(struct nwl_dsi *dsi)
+{
+	int ret = 0;
+
+	/* otherwise the display stays blank */
+	usleep_range(200, 300);
+
+	if (dsi->rstc)
+		ret = reset_control_deassert(dsi->rstc);
+
+	return ret;
+}
+
+static int imx8mq_dsi_poweroff(struct nwl_dsi *dsi)
+{
+	int ret = 0;
+
+	if (dsi->quirks & SRC_RESET_QUIRK)
+		return 0;
+
+	if (dsi->rstc)
+		ret = reset_control_assert(dsi->rstc);
+	return ret;
+}
+
+static const struct drm_bridge_timings nwl_dsi_timings = {
+	.input_bus_flags = DRM_BUS_FLAG_DE_LOW,
+};
+
+static const struct nwl_dsi_platform_data imx8mq_dev = {
+	.poweron = &imx8mq_dsi_poweron,
+	.poweroff = &imx8mq_dsi_poweroff,
+	.select_input = &imx8mq_dsi_select_input,
+	.deselect_input = &imx8mq_dsi_deselect_input,
+	.clk_config = {
+		{ .id = NWL_DSI_CLK_CORE, .present = true },
+	},
+};
+
+static const struct of_device_id nwl_dsi_dt_ids[] = {
+	{ .compatible = "fsl,imx8mq-nwl-dsi", .data = &imx8mq_dev, },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, nwl_dsi_dt_ids);
+
+static const struct soc_device_attribute nwl_dsi_quirks_match[] = {
+	{ .soc_id = "i.MX8MQ", .revision = "2.0",
+	  .data = (void *)(E11418_HS_MODE_QUIRK | SRC_RESET_QUIRK) },
+	{ /* sentinel. */ },
+};
+
+static int nwl_dsi_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	const struct of_device_id *of_id = of_match_device(nwl_dsi_dt_ids, dev);
+	const struct nwl_dsi_platform_data *pdata = of_id->data;
+	const struct soc_device_attribute *attr;
+	struct nwl_dsi *dsi;
+	int ret;
+
+	dsi = devm_kzalloc(dev, sizeof(*dsi), GFP_KERNEL);
+	if (!dsi)
+		return -ENOMEM;
+
+	dsi->dev = dev;
+	dsi->pdata = pdata;
+
+	ret = nwl_dsi_parse_dt(dsi);
+	if (ret)
+		return ret;
+
+	ret = devm_request_irq(dev, dsi->irq, nwl_dsi_irq_handler, 0,
+			       dev_name(dev), dsi);
+	if (ret < 0) {
+		DRM_DEV_ERROR(dev, "Failed to request IRQ %d: %d\n", dsi->irq,
+			      ret);
+		return ret;
+	}
+
+	dsi->dsi_host.ops = &nwl_dsi_host_ops;
+	dsi->dsi_host.dev = dev;
+	ret = mipi_dsi_host_register(&dsi->dsi_host);
+	if (ret) {
+		DRM_DEV_ERROR(dev, "Failed to register MIPI host: %d\n", ret);
+		return ret;
+	}
+
+	attr = soc_device_match(nwl_dsi_quirks_match);
+	if (attr)
+		dsi->quirks = (uintptr_t)attr->data;
+
+	dsi->bridge.driver_private = dsi;
+	dsi->bridge.funcs = &nwl_dsi_bridge_funcs;
+	dsi->bridge.of_node = dev->of_node;
+	dsi->bridge.timings = &nwl_dsi_timings;
+
+	dev_set_drvdata(dev, dsi);
+	pm_runtime_enable(dev);
+	return 0;
+}
+
+static int nwl_dsi_remove(struct platform_device *pdev)
+{
+	struct nwl_dsi *dsi = platform_get_drvdata(pdev);
+
+	mipi_dsi_host_unregister(&dsi->dsi_host);
+	pm_runtime_disable(&pdev->dev);
+	return 0;
+}
+
+static struct platform_driver nwl_dsi_driver = {
+	.probe		= nwl_dsi_probe,
+	.remove		= nwl_dsi_remove,
+	.driver		= {
+		.of_match_table = nwl_dsi_dt_ids,
+		.name	= DRV_NAME,
+	},
+};
+
+module_platform_driver(nwl_dsi_driver);
+
+MODULE_AUTHOR("NXP Semiconductor");
+MODULE_AUTHOR("Purism SPC");
+MODULE_DESCRIPTION("Northwest Logic MIPI-DSI driver");
+MODULE_LICENSE("GPL"); /* GPLv2 or later */

drivers/gpu/drm/bridge/nwl-dsi.h new file +134 -0

new file mode 100644
index 000000000000..a247a8a11c7c
@@ -0,0 +1,144 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * NWL MIPI DSI host driver
+ *
+ * Copyright (C) 2017 NXP
+ * Copyright (C) 2019 Purism SPC
+ */
+#ifndef __NWL_DSI_H__
+#define __NWL_DSI_H__
+
+/* DSI HOST registers */
+#define NWL_DSI_CFG_NUM_LANES			0x0
+#define NWL_DSI_CFG_NONCONTINUOUS_CLK		0x4
+#define NWL_DSI_CFG_T_PRE			0x8
+#define NWL_DSI_CFG_T_POST			0xc
+#define NWL_DSI_CFG_TX_GAP			0x10
+#define NWL_DSI_CFG_AUTOINSERT_EOTP		0x14
+#define NWL_DSI_CFG_EXTRA_CMDS_AFTER_EOTP	0x18
+#define NWL_DSI_CFG_HTX_TO_COUNT		0x1c
+#define NWL_DSI_CFG_LRX_H_TO_COUNT		0x20
+#define NWL_DSI_CFG_BTA_H_TO_COUNT		0x24
+#define NWL_DSI_CFG_TWAKEUP			0x28
+#define NWL_DSI_CFG_STATUS_OUT			0x2c
+#define NWL_DSI_RX_ERROR_STATUS			0x30
+
+/* DSI DPI registers */
+#define NWL_DSI_PIXEL_PAYLOAD_SIZE		0x200
+#define NWL_DSI_PIXEL_FIFO_SEND_LEVEL		0x204
+#define NWL_DSI_INTERFACE_COLOR_CODING		0x208
+#define NWL_DSI_PIXEL_FORMAT			0x20c
+#define NWL_DSI_VSYNC_POLARITY			0x210
+#define NWL_DSI_VSYNC_POLARITY_ACTIVE_LOW	0
+#define NWL_DSI_VSYNC_POLARITY_ACTIVE_HIGH	BIT(1)
+
+#define NWL_DSI_HSYNC_POLARITY			0x214
+#define NWL_DSI_HSYNC_POLARITY_ACTIVE_LOW	0
+#define NWL_DSI_HSYNC_POLARITY_ACTIVE_HIGH	BIT(1)
+
+#define NWL_DSI_VIDEO_MODE			0x218
+#define NWL_DSI_HFP				0x21c
+#define NWL_DSI_HBP				0x220
+#define NWL_DSI_HSA				0x224
+#define NWL_DSI_ENABLE_MULT_PKTS		0x228
+#define NWL_DSI_VBP				0x22c
+#define NWL_DSI_VFP				0x230
+#define NWL_DSI_BLLP_MODE			0x234
+#define NWL_DSI_USE_NULL_PKT_BLLP		0x238
+#define NWL_DSI_VACTIVE				0x23c
+#define NWL_DSI_VC				0x240
+
+/* DSI APB PKT control */
+#define NWL_DSI_TX_PAYLOAD			0x280
+#define NWL_DSI_PKT_CONTROL			0x284
+#define NWL_DSI_SEND_PACKET			0x288
+#define NWL_DSI_PKT_STATUS			0x28c
+#define NWL_DSI_PKT_FIFO_WR_LEVEL		0x290
+#define NWL_DSI_PKT_FIFO_RD_LEVEL		0x294
+#define NWL_DSI_RX_PAYLOAD			0x298
+#define NWL_DSI_RX_PKT_HEADER			0x29c
+
+/* DSI IRQ handling */
+#define NWL_DSI_IRQ_STATUS			0x2a0
+#define NWL_DSI_SM_NOT_IDLE			BIT(0)
+#define NWL_DSI_TX_PKT_DONE			BIT(1)
+#define NWL_DSI_DPHY_DIRECTION			BIT(2)
+#define NWL_DSI_TX_FIFO_OVFLW			BIT(3)
+#define NWL_DSI_TX_FIFO_UDFLW			BIT(4)
+#define NWL_DSI_RX_FIFO_OVFLW			BIT(5)
+#define NWL_DSI_RX_FIFO_UDFLW			BIT(6)
+#define NWL_DSI_RX_PKT_HDR_RCVD			BIT(7)
+#define NWL_DSI_RX_PKT_PAYLOAD_DATA_RCVD	BIT(8)
+#define NWL_DSI_BTA_TIMEOUT			BIT(29)
+#define NWL_DSI_LP_RX_TIMEOUT			BIT(30)
+#define NWL_DSI_HS_TX_TIMEOUT			BIT(31)
+
+#define NWL_DSI_IRQ_STATUS2			0x2a4
+#define NWL_DSI_SINGLE_BIT_ECC_ERR		BIT(0)
+#define NWL_DSI_MULTI_BIT_ECC_ERR		BIT(1)
+#define NWL_DSI_CRC_ERR				BIT(2)
+
+#define NWL_DSI_IRQ_MASK			0x2a8
+#define NWL_DSI_SM_NOT_IDLE_MASK		BIT(0)
+#define NWL_DSI_TX_PKT_DONE_MASK		BIT(1)
+#define NWL_DSI_DPHY_DIRECTION_MASK		BIT(2)
+#define NWL_DSI_TX_FIFO_OVFLW_MASK		BIT(3)
+#define NWL_DSI_TX_FIFO_UDFLW_MASK		BIT(4)
+#define NWL_DSI_RX_FIFO_OVFLW_MASK		BIT(5)
+#define NWL_DSI_RX_FIFO_UDFLW_MASK		BIT(6)
+#define NWL_DSI_RX_PKT_HDR_RCVD_MASK		BIT(7)
+#define NWL_DSI_RX_PKT_PAYLOAD_DATA_RCVD_MASK	BIT(8)
+#define NWL_DSI_BTA_TIMEOUT_MASK		BIT(29)
+#define NWL_DSI_LP_RX_TIMEOUT_MASK		BIT(30)
+#define NWL_DSI_HS_TX_TIMEOUT_MASK		BIT(31)
+
+#define NWL_DSI_IRQ_MASK2			0x2ac
+#define NWL_DSI_SINGLE_BIT_ECC_ERR_MASK		BIT(0)
+#define NWL_DSI_MULTI_BIT_ECC_ERR_MASK		BIT(1)
+#define NWL_DSI_CRC_ERR_MASK			BIT(2)
+
+/*
+ * PKT_CONTROL format:
+ * [15: 0] - word count
+ * [17:16] - virtual channel
+ * [23:18] - data type
+ * [24]	   - LP or HS select (0 - LP, 1 - HS)
+ * [25]	   - perform BTA after packet is sent
+ * [26]	   - perform BTA only, no packet tx
+ */
+#define NWL_DSI_WC(x)		FIELD_PREP(GENMASK(15, 0), (x))
+#define NWL_DSI_TX_VC(x)	FIELD_PREP(GENMASK(17, 16), (x))
+#define NWL_DSI_TX_DT(x)	FIELD_PREP(GENMASK(23, 18), (x))
+#define NWL_DSI_HS_SEL(x)	FIELD_PREP(GENMASK(24, 24), (x))
+#define NWL_DSI_BTA_TX(x)	FIELD_PREP(GENMASK(25, 25), (x))
+#define NWL_DSI_BTA_NO_TX(x)	FIELD_PREP(GENMASK(26, 26), (x))
+
+/*
+ * RX_PKT_HEADER format:
+ * [15: 0] - word count
+ * [21:16] - data type
+ * [23:22] - virtual channel
+ */
+#define NWL_DSI_RX_DT(x)	FIELD_GET(GENMASK(21, 16), (x))
+#define NWL_DSI_RX_VC(x)	FIELD_GET(GENMASK(23, 22), (x))
+
+/* DSI Video mode */
+#define NWL_DSI_VM_BURST_MODE_WITH_SYNC_PULSES		0
+#define NWL_DSI_VM_NON_BURST_MODE_WITH_SYNC_EVENTS	BIT(0)
+#define NWL_DSI_VM_BURST_MODE				BIT(1)
+
+/* * DPI color coding */
+#define NWL_DSI_DPI_16_BIT_565_PACKED	0
+#define NWL_DSI_DPI_16_BIT_565_ALIGNED	1
+#define NWL_DSI_DPI_16_BIT_565_SHIFTED	2
+#define NWL_DSI_DPI_18_BIT_PACKED	3

drivers/gpu/drm/bridge/nwl-dsi.h line 144

Quoted 10 lines

drivers/gpu/drm/bridge/nwl-dsi.h new file +10 -0

+#define NWL_DSI_DPI_18_BIT_ALIGNED	4
+#define NWL_DSI_DPI_24_BIT		5
+
+/* * DPI Pixel format */
+#define NWL_DSI_PIXEL_FORMAT_16  0
+#define NWL_DSI_PIXEL_FORMAT_18  BIT(0)
+#define NWL_DSI_PIXEL_FORMAT_18L BIT(1)
+#define NWL_DSI_PIXEL_FORMAT_24  (BIT(0) | BIT(1))
+
+#endif /* __NWL_DSI_H__ */

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel