xilinx: Various DT changes and syncups
Subsystems (2)
cover xilinx: Various DT changes and syncups
Hi,
I am sending some patches to fix bugs we found in xilinx release cycle. Also do some syncs to keep kernel/u-boot dts in pseudo sync.
Thanks,
Michal
Jan Kiszka (1):
arm64: dts: zcu100-revC: Give wifi some time after power-on
Michal Simek (4):
arm64: zynqmp: Remove incorrect phy from DT for zcu102-revB up
arm64: dts: zynqmp: Fix node names which contain "_"
arm64: zynqmp: Sync gpio-controller name location
arm64: zynqmp: Sync gem clock nodes with mainline Linux
Rob Herring (1):
arm64: dts: Remove inconsistent use of 'arm,armv8' compatible string
Sudeep Holla (1):
arm64: dts: zynqmp: replace gpio-key,wakeup with wakeup-source
property
Zumeng Chen (1):
ARM: dts: zynq: enablement of coresight topology
arch/arm/dts/zynq-7000.dtsi | 135 ++++++++++++++++++++++++++++ arch/arm/dts/zynqmp-clk-ccf.dtsi | 22 +++-- arch/arm/dts/zynqmp-clk.dtsi | 4 +- arch/arm/dts/zynqmp-zcu100-revC.dts | 7 +- arch/arm/dts/zynqmp-zcu102-revA.dts | 12 +-- arch/arm/dts/zynqmp-zcu102-revB.dts | 2 +- arch/arm/dts/zynqmp-zcu106-revA.dts | 4 +- arch/arm/dts/zynqmp-zcu111-revA.dts | 4 +- arch/arm/dts/zynqmp.dtsi | 14 +-- 9 files changed, 172 insertions(+), 32 deletions(-)
Signature · 1 line
2.24.0
PATCH 1/8 arm64: zynqmp: Remove incorrect phy from DT for zcu102-revB up
zcu102-revB/up are not removing phy from revA properly because of incorrect name.
---
arch/arm/dts/zynqmp-zcu102-revB.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/dts/zynqmp-zcu102-revB.dts +1 -1
@@ -25,7 +25,7 @@ /* reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>; */ }; /* Cleanup from RevA */ - /delete-node/ phy at 21; + /delete-node/ ethernet-phy at 21; }; /* Fix collision with u61 */
Signature · 1 line
2.24.0
PATCH 2/8 arm64: dts: Remove inconsistent use of 'arm, armv8' compatible string
In reply to Michal SimekFrom: Rob Herring <[email protected]>
The 'arm,armv8' compatible string is only for software models. It adds little value otherwise and is inconsistently used as a fallback on some platforms. Remove it from those platforms.
This fixes warnings generated by the DT schema.
---
arch/arm/dts/zynqmp.dtsi | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-)
arch/arm/dts/zynqmp.dtsi +4 -4
@@ -25,7 +25,7 @@ #size-cells = <0>; cpu0: cpu at 0 { - compatible = "arm,cortex-a53", "arm,armv8"; + compatible = "arm,cortex-a53"; device_type = "cpu"; enable-method = "psci"; operating-points-v2 = <&cpu_opp_table>;
@@ -34,7 +34,7 @@ }; cpu1: cpu at 1 { - compatible = "arm,cortex-a53", "arm,armv8"; + compatible = "arm,cortex-a53"; device_type = "cpu"; enable-method = "psci"; reg = <0x1>;
@@ -43,7 +43,7 @@ }; cpu2: cpu at 2 { - compatible = "arm,cortex-a53", "arm,armv8"; + compatible = "arm,cortex-a53"; device_type = "cpu"; enable-method = "psci"; reg = <0x2>;
@@ -52,7 +52,7 @@ }; cpu3: cpu at 3 { - compatible = "arm,cortex-a53", "arm,armv8"; + compatible = "arm,cortex-a53"; device_type = "cpu"; enable-method = "psci"; reg = <0x3>;
Signature · 1 line
2.24.0
PATCH 2/8 arm64: dts: Remove inconsistent use of 'arm, armv8' compatible string
Quoted 26 lines · Michal Simek
From: Rob Herring <[email protected]>
The 'arm,armv8' compatible string is only for software models. It adds little value otherwise and is inconsistently used as a fallback on some platforms. Remove it from those platforms.
This fixes warnings generated by the DT schema.
Reported-by Michal Simek <[email protected]>Cc Mark Rutland <[email protected]>Cc Will Deacon <[email protected]>Acked-by Antoine Tenart <[email protected]>Acked-by Nishanth Menon <[email protected]>Acked-by Maxime Ripard <[email protected]>Acked-by Chanho Min <[email protected]>Acked-by Masahiro Yamada <[email protected]>Acked-by Gregory CLEMENT <[email protected]>Acked-by Thierry Reding <[email protected]>Acked-by Heiko Stuebner <[email protected]>Acked-by Simon Horman <[email protected]>Acked-by Tero Kristo <[email protected]>Acked-by Wei Xu <[email protected]>Acked-by Liviu Dudau <[email protected]>
Quoted 8 lines
Acked-by Matthias Brugger <[email protected]>Acked-by Michal Simek <[email protected]>Acked-by Scott Branden <[email protected]>Acked-by Kevin Hilman <[email protected]>Acked-by Chunyan Zhang <[email protected]>Acked-by Robert Richter <[email protected]>Acked-by Jisheng Zhang <[email protected]>Acked-by Dinh Nguyen <[email protected]>
I know you are importing this commit from Linux,
but these Ack lines look weird to me...
Quoted 51 lines
Signed-off-by Rob Herring <[email protected]>Signed-off-by Arnd Bergmann <[email protected]>Signed-off-by Michal Simek <[email protected]>---
arch/arm/dts/zynqmp.dtsi | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-)arch/arm/dts/zynqmp.dtsi +4
-5@@ -25,7 +25,7 @@ #size-cells = <0>; cpu0: cpu at 0 { - compatible = "arm,cortex-a53", "arm,armv8"; + compatible = "arm,cortex-a53"; device_type = "cpu"; enable-method = "psci"; operating-points-v2 = <&cpu_opp_table>;@@ -34,7 +34,7 @@ }; cpu1: cpu at 1 { - compatible = "arm,cortex-a53", "arm,armv8"; + compatible = "arm,cortex-a53"; device_type = "cpu"; enable-method = "psci"; reg = <0x1>;@@ -43,7 +43,7 @@ }; cpu2: cpu at 2 { - compatible = "arm,cortex-a53", "arm,armv8"; + compatible = "arm,cortex-a53"; device_type = "cpu"; enable-method = "psci"; reg = <0x2>;@@ -52,7 +52,7 @@ }; cpu3: cpu at 3 { - compatible = "arm,cortex-a53", "arm,armv8"; + compatible = "arm,cortex-a53"; device_type = "cpu"; enable-method = "psci"; reg = <0x3>; --2.24.0
Signature · 2 lines
Best Regards Masahiro Yamada
PATCH 2/8 arm64: dts: Remove inconsistent use of 'arm, armv8' compatible string
Quoted 37 lines · Masahiro Yamada
Quoted 26 lines · Michal Simek
From: Rob Herring <[email protected]>
The 'arm,armv8' compatible string is only for software models. It adds little value otherwise and is inconsistently used as a fallback on some platforms. Remove it from those platforms.
This fixes warnings generated by the DT schema.
Reported-by Michal Simek <[email protected]>Cc Mark Rutland <[email protected]>Cc Will Deacon <[email protected]>Acked-by Antoine Tenart <[email protected]>Acked-by Nishanth Menon <[email protected]>Acked-by Maxime Ripard <[email protected]>Acked-by Chanho Min <[email protected]>Acked-by Masahiro Yamada <[email protected]>Acked-by Gregory CLEMENT <[email protected]>Acked-by Thierry Reding <[email protected]>Acked-by Heiko Stuebner <[email protected]>Acked-by Simon Horman <[email protected]>Acked-by Tero Kristo <[email protected]>Acked-by Wei Xu <[email protected]>Acked-by Liviu Dudau <[email protected]>Quoted 8 lines
Acked-by Matthias Brugger <[email protected]>Acked-by Michal Simek <[email protected]>Acked-by Scott Branden <[email protected]>Acked-by Kevin Hilman <[email protected]>Acked-by Chunyan Zhang <[email protected]>Acked-by Robert Richter <[email protected]>Acked-by Jisheng Zhang <[email protected]>Acked-by Dinh Nguyen <[email protected]>
Quoted 2 lines
I know you are importing this commit from Linux,
but these Ack lines look weird to me...
I have not a problem to remove them but not sure if this is the right thing to do.
Thanks,
Michal
PATCH 3/8 arm64: dts: zynqmp: Fix node names which contain "_"
In reply to Michal Simeks/_/-/ for node names.
It fixes warnings like this:
... Warning (node_name_chars_strict): /cpu_opp_table:
Character '_' not recommended in node name ...
Issues reported by make dtbs W=12
---
arch/arm/dts/zynqmp-clk.dtsi | 4 ++-- arch/arm/dts/zynqmp-zcu100-revC.dts | 4 ++-- arch/arm/dts/zynqmp-zcu102-revA.dts | 10 +++++----- arch/arm/dts/zynqmp-zcu106-revA.dts | 2 +- arch/arm/dts/zynqmp-zcu111-revA.dts | 2 +- arch/arm/dts/zynqmp.dtsi | 4 ++-- 6 files changed, 13 insertions(+), 13 deletions(-)
arch/arm/dts/zynqmp-clk.dtsi +2 -2
@@ -61,13 +61,13 @@ clock-accuracy = <100>; }; - dpdma_clk: dpdma_clk { + dpdma_clk: dpdma-clk { compatible = "fixed-clock"; #clock-cells = <0x0>; clock-frequency = <533000000>; }; - drm_clock: drm_clock { + drm_clock: drm-clock { compatible = "fixed-clock"; #clock-cells = <0x0>; clock-frequency = <262750000>;
arch/arm/dts/zynqmp-zcu100-revC.dts +2 -2
@@ -95,7 +95,7 @@ linux,default-trigger = "bluetooth-power"; }; - vbus_det { /* U5 USB5744 VBUS detection via MIO25 */ + vbus-det { /* U5 USB5744 VBUS detection via MIO25 */ label = "vbus_det"; gpios = <&gpio 25 GPIO_ACTIVE_HIGH>; default-state = "on";
@@ -120,7 +120,7 @@ regulator-boot-on; }; - sdio_pwrseq: sdio_pwrseq { + sdio_pwrseq: sdio-pwrseq { compatible = "mmc-pwrseq-simple"; reset-gpios = <&gpio 7 GPIO_ACTIVE_LOW>; /* WIFI_EN */ };
arch/arm/dts/zynqmp-zcu102-revA.dts +5 -5
@@ -58,7 +58,7 @@ leds { compatible = "gpio-leds"; - heartbeat_led { + heartbeat-led { label = "heartbeat"; gpios = <&gpio 23 GPIO_ACTIVE_HIGH>; linux,default-trigger = "heartbeat";
@@ -213,25 +213,25 @@ gpio-line-names = "PS_GTR_LAN_SEL0", "PS_GTR_LAN_SEL1", "PS_GTR_LAN_SEL2", "PS_GTR_LAN_SEL3", "PCI_CLK_DIR_SEL", "IIC_MUX_RESET_B", "GEM3_EXP_RESET_B", "", "", "", "", "", "", "", "", ""; - gtr_sel0 { + gtr-sel0 { gpio-hog; gpios = <0 0>; output-low; /* PCIE = 0, DP = 1 */ line-name = "sel0"; }; - gtr_sel1 { + gtr-sel1 { gpio-hog; gpios = <1 0>; output-high; /* PCIE = 0, DP = 1 */ line-name = "sel1"; }; - gtr_sel2 { + gtr-sel2 { gpio-hog; gpios = <2 0>; output-high; /* PCIE = 0, USB0 = 1 */ line-name = "sel2"; }; - gtr_sel3 { + gtr-sel3 { gpio-hog; gpios = <3 0>; output-high; /* PCIE = 0, SATA = 1 */
arch/arm/dts/zynqmp-zcu106-revA.dts +1 -1
@@ -58,7 +58,7 @@ leds { compatible = "gpio-leds"; - heartbeat_led { + heartbeat-led { label = "heartbeat"; gpios = <&gpio 23 GPIO_ACTIVE_HIGH>; linux,default-trigger = "heartbeat";
arch/arm/dts/zynqmp-zcu111-revA.dts +1 -1
@@ -58,7 +58,7 @@ leds { compatible = "gpio-leds"; - heartbeat_led { + heartbeat-led { label = "heartbeat"; gpios = <&gpio 23 GPIO_ACTIVE_HIGH>; linux,default-trigger = "heartbeat";
arch/arm/dts/zynqmp.dtsi +2 -2
@@ -74,7 +74,7 @@ }; }; - cpu_opp_table: cpu_opp_table { + cpu_opp_table: cpu-opp-table { compatible = "operating-points-v2"; opp-shared; opp00 {
@@ -252,7 +252,7 @@ }; }; - amba_apu: amba_apu at 0 { + amba_apu: amba-apu at 0 { compatible = "simple-bus"; #address-cells = <2>; #size-cells = <1>;
Signature · 1 line
2.24.0
PATCH 4/8 arm64: dts: zcu100-revC: Give wifi some time after power-on
In reply to Michal SimekFrom: Jan Kiszka <[email protected]>
Somewhere along recent changes to power control of the wl1831, power-on became very unreliable on the Ultra96, failing like this:
wl1271_sdio: probe of mmc2:0001:1 failed with error -16wl1271_sdio: probe of mmc2:0001:2 failed with error -16
After playing with some dt parameters and comparing to other users of this chip, it turned out we need some power-on delay to make things stable again. In contrast to those other users which define 200 ms, Ultra96 is already happy with 10 ms.
---
arch/arm/dts/zynqmp-zcu100-revC.dts | 1 + 1 file changed, 1 insertion(+)
arch/arm/dts/zynqmp-zcu100-revC.dts +1 -0
@@ -123,6 +123,7 @@ sdio_pwrseq: sdio-pwrseq { compatible = "mmc-pwrseq-simple"; reset-gpios = <&gpio 7 GPIO_ACTIVE_LOW>; /* WIFI_EN */ + post-power-on-delay-ms = <10>; }; ina226 {
Signature · 1 line
2.24.0
PATCH 5/8 arm64: dts: zynqmp: replace gpio-key, wakeup with wakeup-source property
In reply to Michal SimekFrom: Sudeep Holla <[email protected]>
Most of the legacy "gpio-key,wakeup" boolean property is already replaced with "wakeup-source". However few occurrences of old property has popped up again, probably from the remnants in downstream trees.
This patch replaces the legacy properties with the unified "wakeup-source" property introduced by:
"Input: gpio_keys - switch to using generic device properties" (sha1: 700a38b27eefc582099fdf69effacfad0ad738a4)
---
arch/arm/dts/zynqmp-zcu100-revC.dts | 2 +- arch/arm/dts/zynqmp-zcu102-revA.dts | 2 +- arch/arm/dts/zynqmp-zcu106-revA.dts | 2 +- arch/arm/dts/zynqmp-zcu111-revA.dts | 2 +- 4 files changed, 4 insertions(+), 4 deletions(-)
arch/arm/dts/zynqmp-zcu100-revC.dts +1 -1
@@ -53,7 +53,7 @@ label = "sw4"; gpios = <&gpio 23 GPIO_ACTIVE_LOW>; linux,code = <KEY_POWER>; - gpio-key,wakeup; + wakeup-source; autorepeat; }; };
arch/arm/dts/zynqmp-zcu102-revA.dts +1 -1
@@ -51,7 +51,7 @@ label = "sw19"; gpios = <&gpio 22 GPIO_ACTIVE_HIGH>; linux,code = <KEY_DOWN>; - gpio-key,wakeup; + wakeup-source; autorepeat; }; };
arch/arm/dts/zynqmp-zcu106-revA.dts +1 -1
@@ -51,7 +51,7 @@ label = "sw19"; gpios = <&gpio 22 GPIO_ACTIVE_HIGH>; linux,code = <KEY_DOWN>; - gpio-key,wakeup; + wakeup-source; autorepeat; }; };
arch/arm/dts/zynqmp-zcu111-revA.dts +1 -1
@@ -51,7 +51,7 @@ label = "sw19"; gpios = <&gpio 22 GPIO_ACTIVE_HIGH>; linux,code = <KEY_DOWN>; - gpio-key,wakeup; + wakeup-source; autorepeat; }; };
Signature · 1 line
2.24.0
PATCH 6/8 arm64: zynqmp: Sync gpio-controller name location
In reply to Michal SimekSync location with mainline kernel.
Added by Linux kernel commit 75926f07baae
("arm64: dts: zynqmp: Add missing gpio-controller to ps gpio").
---
arch/arm/dts/zynqmp.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/dts/zynqmp.dtsi +1 -1
@@ -626,12 +626,12 @@ compatible = "xlnx,zynqmp-gpio-1.0"; status = "disabled"; #gpio-cells = <0x2>; + gpio-controller; interrupt-parent = <&gic>; interrupts = <0 16 4>; interrupt-controller; #interrupt-cells = <2>; reg = <0x0 0xff0a0000 0x0 0x1000>; - gpio-controller; power-domains = <&zynqmp_firmware PD_GPIO>; };
Signature · 1 line
2.24.0
PATCH 7/8 arm64: zynqmp: Sync gem clock nodes with mainline Linux
In reply to Michal SimekJust fixing indentation and update year in Copyright.
---
arch/arm/dts/zynqmp-clk-ccf.dtsi | 22 +++++++++++++--------- 1 file changed, 13 insertions(+), 9 deletions(-)
arch/arm/dts/zynqmp-clk-ccf.dtsi +13 -9
@@ -2,7 +2,7 @@ /* * Clock specification for Xilinx ZynqMP * - * (C) Copyright 2017, Xilinx, Inc. + * (C) Copyright 2017 - 2019, Xilinx, Inc. * * Michal Simek <[email protected]> */
@@ -173,26 +173,30 @@ }; &gem0 { - clocks = <&zynqmp_clk LPD_LSBUS>, <&zynqmp_clk GEM0_REF>, <&zynqmp_clk GEM0_TX>, - <&zynqmp_clk GEM0_RX>, <&zynqmp_clk GEM_TSU>; + clocks = <&zynqmp_clk LPD_LSBUS>, <&zynqmp_clk GEM0_REF>, + <&zynqmp_clk GEM0_TX>, <&zynqmp_clk GEM0_RX>, + <&zynqmp_clk GEM_TSU>; clock-names = "pclk", "hclk", "tx_clk", "rx_clk", "tsu_clk"; }; &gem1 { - clocks = <&zynqmp_clk LPD_LSBUS>, <&zynqmp_clk GEM1_REF>, <&zynqmp_clk GEM1_TX>, - <&zynqmp_clk GEM1_RX>, <&zynqmp_clk GEM_TSU>; + clocks = <&zynqmp_clk LPD_LSBUS>, <&zynqmp_clk GEM1_REF>, + <&zynqmp_clk GEM1_TX>, <&zynqmp_clk GEM1_RX>, + <&zynqmp_clk GEM_TSU>; clock-names = "pclk", "hclk", "tx_clk", "rx_clk", "tsu_clk"; }; &gem2 { - clocks = <&zynqmp_clk LPD_LSBUS>, <&zynqmp_clk GEM2_REF>, <&zynqmp_clk GEM2_TX>, - <&zynqmp_clk GEM2_RX>, <&zynqmp_clk GEM_TSU>; + clocks = <&zynqmp_clk LPD_LSBUS>, <&zynqmp_clk GEM2_REF>, + <&zynqmp_clk GEM2_TX>, <&zynqmp_clk GEM2_RX>, + <&zynqmp_clk GEM_TSU>; clock-names = "pclk", "hclk", "tx_clk", "rx_clk", "tsu_clk"; }; &gem3 { - clocks = <&zynqmp_clk LPD_LSBUS>, <&zynqmp_clk GEM3_REF>, <&zynqmp_clk GEM3_TX>, - <&zynqmp_clk GEM3_RX>, <&zynqmp_clk GEM_TSU>; + clocks = <&zynqmp_clk LPD_LSBUS>, <&zynqmp_clk GEM3_REF>, + <&zynqmp_clk GEM3_TX>, <&zynqmp_clk GEM3_RX>, + <&zynqmp_clk GEM_TSU>; clock-names = "pclk", "hclk", "tx_clk", "rx_clk", "tsu_clk"; };
Signature · 1 line
2.24.0
PATCH 8/8 ARM: dts: zynq: enablement of coresight topology
In reply to Michal SimekFrom: Zumeng Chen <[email protected]>
This patch is to build the coresight topology structure of zynq-7000 series according to the docs of coresight and userguide of zynq-7000.
---
arch/arm/dts/zynq-7000.dtsi | 135 ++++++++++++++++++++++++++++++++++++ 1 file changed, 135 insertions(+)
arch/arm/dts/zynq-7000.dtsi +135 -0
@@ -62,6 +62,39 @@ regulator-always-on; }; + replicator { + compatible = "arm,coresight-static-replicator"; + clocks = <&clkc 27>, <&clkc 46>, <&clkc 47>; + clock-names = "apb_pclk", "dbg_trc", "dbg_apb"; + + out-ports { + #address-cells = <1>; + #size-cells = <0>; + + /* replicator output ports */ + port at 0 { + reg = <0>; + replicator_out_port0: endpoint { + remote-endpoint = <&tpiu_in_port>; + }; + }; + port at 1 { + reg = <1>; + replicator_out_port1: endpoint { + remote-endpoint = <&etb_in_port>; + }; + }; + }; + in-ports { + /* replicator input port */ + port { + replicator_in_port0: endpoint { + remote-endpoint = <&funnel_out_port>; + }; + }; + }; + }; + amba: amba { u-boot,dm-pre-reloc; compatible = "simple-bus";
@@ -415,5 +448,107 @@ reg = <0xf8005000 0x1000>; timeout-sec = <10>; }; + + etb at f8801000 { + compatible = "arm,coresight-etb10", "arm,primecell"; + reg = <0xf8801000 0x1000>; + clocks = <&clkc 27>, <&clkc 46>, <&clkc 47>; + clock-names = "apb_pclk", "dbg_trc", "dbg_apb"; + in-ports { + port { + etb_in_port: endpoint { + remote-endpoint = <&replicator_out_port1>; + }; + }; + }; + }; + + tpiu at f8803000 { + compatible = "arm,coresight-tpiu", "arm,primecell"; + reg = <0xf8803000 0x1000>; + clocks = <&clkc 27>, <&clkc 46>, <&clkc 47>; + clock-names = "apb_pclk", "dbg_trc", "dbg_apb"; + in-ports { + port { + tpiu_in_port: endpoint { + remote-endpoint = <&replicator_out_port0>; + }; + }; + }; + }; + + funnel at f8804000 { + compatible = "arm,coresight-static-funnel", "arm,primecell"; + reg = <0xf8804000 0x1000>; + clocks = <&clkc 27>, <&clkc 46>, <&clkc 47>; + clock-names = "apb_pclk", "dbg_trc", "dbg_apb"; + + /* funnel output ports */ + out-ports { + port { + funnel_out_port: endpoint { + remote-endpoint = + <&replicator_in_port0>; + }; + }; + }; + + in-ports { + #address-cells = <1>; + #size-cells = <0>; + + /* funnel input ports */ + port at 0 { + reg = <0>; + funnel0_in_port0: endpoint { + remote-endpoint = <&ptm0_out_port>; + }; + }; + + port at 1 { + reg = <1>; + funnel0_in_port1: endpoint { + remote-endpoint = <&ptm1_out_port>; + }; + }; + + port at 2 { + reg = <2>; + funnel0_in_port2: endpoint { + }; + }; + /* The other input ports are not connect to anything */ + }; + }; + + ptm at f889c000 { + compatible = "arm,coresight-etm3x", "arm,primecell"; + reg = <0xf889c000 0x1000>; + clocks = <&clkc 27>, <&clkc 46>, <&clkc 47>; + clock-names = "apb_pclk", "dbg_trc", "dbg_apb"; + cpu = <&cpu0>; + out-ports { + port { + ptm0_out_port: endpoint { + remote-endpoint = <&funnel0_in_port0>; + }; + }; + }; + }; + + ptm at f889d000 { + compatible = "arm,coresight-etm3x", "arm,primecell"; + reg = <0xf889d000 0x1000>; + clocks = <&clkc 27>, <&clkc 46>, <&clkc 47>; + clock-names = "apb_pclk", "dbg_trc", "dbg_apb"; + cpu = <&cpu1>; + out-ports { + port { + ptm1_out_port: endpoint { + remote-endpoint = <&funnel0_in_port1>; + }; + }; + }; + }; }; };
Signature · 1 line
2.24.0
cover xilinx: Various DT changes and syncups
In reply to Michal SimekQuoted 28 lines · Michal Simek
Hi,
I am sending some patches to fix bugs we found in xilinx release cycle. Also do some syncs to keep
kernel/u-bootdts in pseudo sync.Thanks,
MichalJan Kiszka (1):
arm64: dts: zcu100-revC: Give wifi some time after power-onMichal Simek (4):
arm64: zynqmp: Remove incorrect phy from DT for zcu102-revB up
arm64: dts: zynqmp: Fix node names which contain "_"
arm64: zynqmp: Sync gpio-controller name location
arm64: zynqmp: Sync gem clock nodes with mainline LinuxRob Herring (1):
arm64: dts: Remove inconsistent use of 'arm,armv8' compatible stringSudeep Holla (1):
arm64: dts: zynqmp: replace gpio-key,wakeup with wakeup-source
propertyZumeng Chen (1):
ARM: dts: zynq: enablement of coresight topology
Quoted 11 lines
arch/arm/dts/zynq-7000.dtsi | 135 ++++++++++++++++++++++++++++ arch/arm/dts/zynqmp-clk-ccf.dtsi | 22 +++-- arch/arm/dts/zynqmp-clk.dtsi | 4 +- arch/arm/dts/zynqmp-zcu100-revC.dts | 7 +- arch/arm/dts/zynqmp-zcu102-revA.dts | 12 +-- arch/arm/dts/zynqmp-zcu102-revB.dts | 2 +- arch/arm/dts/zynqmp-zcu106-revA.dts | 4 +- arch/arm/dts/zynqmp-zcu111-revA.dts | 4 +- arch/arm/dts/zynqmp.dtsi | 14 +-- 9 files changed, 172 insertions(+), 32 deletions(-)
Apply all.
M
Signature · 14 lines
Michal Simek, Ing. (M.Eng), OpenPGP -> KeyID: FE3D1F91 w: www.monstr.eu p: +42-0-721842854 Maintainer of Linux kernel - Xilinx Microblaze Maintainer of Linux kernel - Xilinx Zynq ARM and ZynqMP ARM64 SoCs U-Boot custodian - Xilinx Microblaze/Zynq/ZynqMP/Versal SoCs -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 195 bytes Desc: OpenPGP digital signature URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200116/b3bbe113/attachment.sig>