make dtbs_check cleanups for qcom thermal

PATCH New Amit Kucheria 1 participant 4 messages Mar 30, 2020

Subsystems (3)

Device tree bindings Arm Qualcomm mailing list Arm Qualcomm support

lore

Share & tools

lore

Amit Kucheria

author

2020-03-30 10:06 UTC #0 lore raw

cover make dtbs_check cleanups for qcom thermal

Clean up the remaining trip-point names in qcom dtsi files. This is similar to the cleanups done before:

commit e8c48eb08ab14 ("arm64: dts: qcom: qcs404: remove unit name for thermal trip points") commit 19e684e835f63 ("arm64: dts: qcom: sdm845: remove unit name for thermal trip points")

Amit Kucheria (3):
arm64: dts: qcom: msm8916: remove unit name for thermal trip points
arm64: dts: qcom: msm8996: remove unit name for thermal trip points
arm64: dts: qcom: msm8998: remove unit name for thermal trip points

 arch/arm64/boot/dts/qcom/msm8916.dtsi |  8 +++---
 arch/arm64/boot/dts/qcom/msm8996.dtsi | 28 ++++++++++----------
 arch/arm64/boot/dts/qcom/msm8998.dtsi | 38 +++++++++++++--------------
 3 files changed, 37 insertions(+), 37 deletions(-)

Signature · 1 line

2.20.1

Amit Kucheria

author

2020-03-30 10:06 UTC #1 lore raw

PATCH 1/3 arm64: dts: qcom: msm8916: remove unit name for thermal trip points

The thermal trip points have unit name but no reg property, so we can remove them. It also fixes the following warnings from 'make dtbs_check' after adding the thermal yaml bindings.

arch/arm64/boot/dts/qcom/apq8016-sbc.dt.yaml: thermal-zones:
gpu-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8016-sbc.dt.yaml: thermal-zones:
camera-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8016-sbc.dt.yaml: thermal-zones:
modem-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'

arch/arm64/boot/dts/qcom/msm8916-mtp.dt.yaml: thermal-zones:
gpu-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8916-mtp.dt.yaml: thermal-zones:
camera-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8916-mtp.dt.yaml: thermal-zones:
modem-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'

Signed-off-by Amit Kucheria <[email protected]>

---
 arch/arm64/boot/dts/qcom/msm8916.dtsi | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

arch/arm64/boot/dts/qcom/msm8916.dtsi +4 -4

index 9f31064f2374e..1a6e28923a45d 100644
@@ -261,7 +261,7 @@
 			thermal-sensors = <&tsens 4>;
 
 			trips {
-				cpu2_3_alert0: trip-point@0 {
+				cpu2_3_alert0: trip-point0 {
 					temperature = <75000>;
 					hysteresis = <2000>;
 					type = "passive";

@@ -291,7 +291,7 @@
 			thermal-sensors = <&tsens 2>;
 
 			trips {
-				gpu_alert0: trip-point@0 {
+				gpu_alert0: trip-point0 {
 					temperature = <75000>;
 					hysteresis = <2000>;
 					type = "passive";

@@ -311,7 +311,7 @@
 			thermal-sensors = <&tsens 1>;
 
 			trips {
-				cam_alert0: trip-point@0 {
+				cam_alert0: trip-point0 {
 					temperature = <75000>;
 					hysteresis = <2000>;
 					type = "hot";

@@ -326,7 +326,7 @@
 			thermal-sensors = <&tsens 0>;
 
 			trips {
-				modem_alert0: trip-point@0 {
+				modem_alert0: trip-point0 {
 					temperature = <85000>;
 					hysteresis = <2000>;
 					type = "hot";

Signature · 1 line

2.20.1

Amit Kucheria

author

2020-03-30 10:06 UTC #2 lore raw

PATCH 2/3 arm64: dts: qcom: msm8996: remove unit name for thermal trip points

In reply to Amit Kucheria

The thermal trip points have unit name but no reg property, so we can remove them. It also fixes the following warnings from 'make dtbs_check' after adding the thermal yaml bindings.

arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
cpu0-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
cpu1-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
cpu2-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
cpu3-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
m4m-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
l3-or-venus-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
cluster0-l2-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
cluster1-l2-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
camera-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
q6-dsp-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
mem-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
modemtx-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'

arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
cpu0-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
cpu1-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
cpu2-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
cpu3-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
m4m-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
l3-or-venus-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
cluster0-l2-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
cluster1-l2-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
camera-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
q6-dsp-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
mem-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
modemtx-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'

Signed-off-by Amit Kucheria <[email protected]>

---
 arch/arm64/boot/dts/qcom/msm8996.dtsi | 28 +++++++++++++--------------
 1 file changed, 14 insertions(+), 14 deletions(-)

arch/arm64/boot/dts/qcom/msm8996.dtsi +14 ~~-14~~

index 7ae082ea14ea8..76a2ef2e01933 100644
@@ -2165,7 +2165,7 @@
 			thermal-sensors = <&tsens0 3>;
 
 			trips {
-				cpu0_alert0: trip-point@0 {
+				cpu0_alert0: trip-point0 {
 					temperature = <75000>;
 					hysteresis = <2000>;
 					type = "passive";

@@ -2186,7 +2186,7 @@
 			thermal-sensors = <&tsens0 5>;
 
 			trips {
-				cpu1_alert0: trip-point@0 {
+				cpu1_alert0: trip-point0 {
 					temperature = <75000>;
 					hysteresis = <2000>;
 					type = "passive";

@@ -2207,7 +2207,7 @@
 			thermal-sensors = <&tsens0 8>;
 
 			trips {
-				cpu2_alert0: trip-point@0 {
+				cpu2_alert0: trip-point0 {
 					temperature = <75000>;
 					hysteresis = <2000>;
 					type = "passive";

@@ -2228,7 +2228,7 @@
 			thermal-sensors = <&tsens0 10>;
 
 			trips {
-				cpu3_alert0: trip-point@0 {
+				cpu3_alert0: trip-point0 {
 					temperature = <75000>;
 					hysteresis = <2000>;
 					type = "passive";

@@ -2249,7 +2249,7 @@
 			thermal-sensors = <&tsens1 6>;
 
 			trips {
-				gpu1_alert0: trip-point@0 {
+				gpu1_alert0: trip-point0 {
 					temperature = <90000>;
 					hysteresis = <2000>;
 					type = "hot";

@@ -2264,7 +2264,7 @@
 			thermal-sensors = <&tsens1 7>;
 
 			trips {
-				gpu2_alert0: trip-point@0 {
+				gpu2_alert0: trip-point0 {
 					temperature = <90000>;
 					hysteresis = <2000>;
 					type = "hot";

@@ -2279,7 +2279,7 @@
 			thermal-sensors = <&tsens0 1>;
 
 			trips {
-				m4m_alert0: trip-point@0 {
+				m4m_alert0: trip-point0 {
 					temperature = <90000>;
 					hysteresis = <2000>;
 					type = "hot";

@@ -2294,7 +2294,7 @@
 			thermal-sensors = <&tsens0 2>;
 
 			trips {
-				l3_or_venus_alert0: trip-point@0 {
+				l3_or_venus_alert0: trip-point0 {
 					temperature = <90000>;
 					hysteresis = <2000>;
 					type = "hot";

@@ -2309,7 +2309,7 @@
 			thermal-sensors = <&tsens0 7>;
 
 			trips {
-				cluster0_l2_alert0: trip-point@0 {
+				cluster0_l2_alert0: trip-point0 {
 					temperature = <90000>;
 					hysteresis = <2000>;
 					type = "hot";

@@ -2324,7 +2324,7 @@
 			thermal-sensors = <&tsens0 12>;
 
 			trips {
-				cluster1_l2_alert0: trip-point@0 {
+				cluster1_l2_alert0: trip-point0 {
 					temperature = <90000>;
 					hysteresis = <2000>;
 					type = "hot";

@@ -2339,7 +2339,7 @@
 			thermal-sensors = <&tsens1 1>;
 
 			trips {
-				camera_alert0: trip-point@0 {
+				camera_alert0: trip-point0 {
 					temperature = <90000>;
 					hysteresis = <2000>;
 					type = "hot";

@@ -2354,7 +2354,7 @@
 			thermal-sensors = <&tsens1 2>;
 
 			trips {
-				q6_dsp_alert0: trip-point@0 {
+				q6_dsp_alert0: trip-point0 {
 					temperature = <90000>;
 					hysteresis = <2000>;
 					type = "hot";

@@ -2369,7 +2369,7 @@
 			thermal-sensors = <&tsens1 3>;
 
 			trips {
-				mem_alert0: trip-point@0 {
+				mem_alert0: trip-point0 {
 					temperature = <90000>;
 					hysteresis = <2000>;
 					type = "hot";

@@ -2384,7 +2384,7 @@
 			thermal-sensors = <&tsens1 4>;
 
 			trips {
-				modemtx_alert0: trip-point@0 {
+				modemtx_alert0: trip-point0 {
 					temperature = <90000>;
 					hysteresis = <2000>;
 					type = "hot";

Signature · 1 line

2.20.1

Amit Kucheria

author

2020-03-30 10:06 UTC #3 lore raw

PATCH 3/3 arm64: dts: qcom: msm8998: remove unit name for thermal trip points

In reply to Amit Kucheria

The thermal trip points have unit name but no reg property, so we can remove them. It also fixes the following warnings from 'make dtbs_check' after adding the thermal yaml bindings.

arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
cpu0-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
cpu1-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
cpu2-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
cpu3-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
cpu4-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
cpu5-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
cpu6-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
cpu7-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
clust0-mhm-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
clust1-mhm-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
cluster1-l2-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
modem-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
mem-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
wlan-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
q6-dsp-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
camera-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
multimedia-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'

arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
cpu0-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
cpu1-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
cpu2-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
cpu3-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
cpu4-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
cpu5-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
cpu6-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
cpu7-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
clust0-mhm-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
clust1-mhm-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
cluster1-l2-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
modem-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
mem-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
wlan-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
q6-dsp-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
camera-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+' arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
multimedia-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'

Signed-off-by Amit Kucheria <[email protected]>

---
 arch/arm64/boot/dts/qcom/msm8998.dtsi | 38 +++++++++++++--------------
 1 file changed, 19 insertions(+), 19 deletions(-)

arch/arm64/boot/dts/qcom/msm8998.dtsi +19 ~~-19~~

index 91f7f2d075978..074c4b614d221 100644
@@ -500,7 +500,7 @@
 			thermal-sensors = <&tsens0 1>;
 
 			trips {
-				cpu0_alert0: trip-point@0 {
+				cpu0_alert0: trip-point0 {
 					temperature = <75000>;
 					hysteresis = <2000>;
 					type = "passive";

@@ -521,7 +521,7 @@
 			thermal-sensors = <&tsens0 2>;
 
 			trips {
-				cpu1_alert0: trip-point@0 {
+				cpu1_alert0: trip-point0 {
 					temperature = <75000>;
 					hysteresis = <2000>;
 					type = "passive";

@@ -542,7 +542,7 @@
 			thermal-sensors = <&tsens0 3>;
 
 			trips {
-				cpu2_alert0: trip-point@0 {
+				cpu2_alert0: trip-point0 {
 					temperature = <75000>;
 					hysteresis = <2000>;
 					type = "passive";

@@ -563,7 +563,7 @@
 			thermal-sensors = <&tsens0 4>;
 
 			trips {
-				cpu3_alert0: trip-point@0 {
+				cpu3_alert0: trip-point0 {
 					temperature = <75000>;
 					hysteresis = <2000>;
 					type = "passive";

@@ -584,7 +584,7 @@
 			thermal-sensors = <&tsens0 7>;
 
 			trips {
-				cpu4_alert0: trip-point@0 {
+				cpu4_alert0: trip-point0 {
 					temperature = <75000>;
 					hysteresis = <2000>;
 					type = "passive";

@@ -605,7 +605,7 @@
 			thermal-sensors = <&tsens0 8>;
 
 			trips {
-				cpu5_alert0: trip-point@0 {
+				cpu5_alert0: trip-point0 {
 					temperature = <75000>;
 					hysteresis = <2000>;
 					type = "passive";

@@ -626,7 +626,7 @@
 			thermal-sensors = <&tsens0 9>;
 
 			trips {
-				cpu6_alert0: trip-point@0 {
+				cpu6_alert0: trip-point0 {
 					temperature = <75000>;
 					hysteresis = <2000>;
 					type = "passive";

@@ -647,7 +647,7 @@
 			thermal-sensors = <&tsens0 10>;
 
 			trips {
-				cpu7_alert0: trip-point@0 {
+				cpu7_alert0: trip-point0 {
 					temperature = <75000>;
 					hysteresis = <2000>;
 					type = "passive";

@@ -668,7 +668,7 @@
 			thermal-sensors = <&tsens0 12>;
 
 			trips {
-				gpu1_alert0: trip-point@0 {
+				gpu1_alert0: trip-point0 {
 					temperature = <90000>;
 					hysteresis = <2000>;
 					type = "hot";

@@ -683,7 +683,7 @@
 			thermal-sensors = <&tsens0 13>;
 
 			trips {
-				gpu2_alert0: trip-point@0 {
+				gpu2_alert0: trip-point0 {
 					temperature = <90000>;
 					hysteresis = <2000>;
 					type = "hot";

@@ -698,7 +698,7 @@
 			thermal-sensors = <&tsens0 5>;
 
 			trips {
-				cluster0_mhm_alert0: trip-point@0 {
+				cluster0_mhm_alert0: trip-point0 {
 					temperature = <90000>;
 					hysteresis = <2000>;
 					type = "hot";

@@ -713,7 +713,7 @@
 			thermal-sensors = <&tsens0 6>;
 
 			trips {
-				cluster1_mhm_alert0: trip-point@0 {
+				cluster1_mhm_alert0: trip-point0 {
 					temperature = <90000>;
 					hysteresis = <2000>;
 					type = "hot";

@@ -728,7 +728,7 @@
 			thermal-sensors = <&tsens0 11>;
 
 			trips {
-				cluster1_l2_alert0: trip-point@0 {
+				cluster1_l2_alert0: trip-point0 {
 					temperature = <90000>;
 					hysteresis = <2000>;
 					type = "hot";

@@ -743,7 +743,7 @@
 			thermal-sensors = <&tsens1 1>;
 
 			trips {
-				modem_alert0: trip-point@0 {
+				modem_alert0: trip-point0 {
 					temperature = <90000>;
 					hysteresis = <2000>;
 					type = "hot";

@@ -758,7 +758,7 @@
 			thermal-sensors = <&tsens1 2>;
 
 			trips {
-				mem_alert0: trip-point@0 {
+				mem_alert0: trip-point0 {
 					temperature = <90000>;
 					hysteresis = <2000>;
 					type = "hot";

@@ -773,7 +773,7 @@
 			thermal-sensors = <&tsens1 3>;
 
 			trips {
-				wlan_alert0: trip-point@0 {
+				wlan_alert0: trip-point0 {
 					temperature = <90000>;
 					hysteresis = <2000>;
 					type = "hot";

@@ -788,7 +788,7 @@
 			thermal-sensors = <&tsens1 4>;
 
 			trips {
-				q6_dsp_alert0: trip-point@0 {
+				q6_dsp_alert0: trip-point0 {
 					temperature = <90000>;
 					hysteresis = <2000>;
 					type = "hot";

@@ -803,7 +803,7 @@
 			thermal-sensors = <&tsens1 5>;
 
 			trips {
-				camera_alert0: trip-point@0 {
+				camera_alert0: trip-point0 {
 					temperature = <90000>;
 					hysteresis = <2000>;
 					type = "hot";

@@ -818,7 +818,7 @@
 			thermal-sensors = <&tsens1 6>;
 
 			trips {
-				multimedia_alert0: trip-point@0 {
+				multimedia_alert0: trip-point0 {
 					temperature = <90000>;
 					hysteresis = <2000>;
 					type = "hot";

Signature · 1 line

2.20.1