Skip to contentSkip to conversation

power: supply: bq25890: fix and extend

PATCH Superseded Michał Mirosław 2 participants 21 messages May 3, 2020

Subsystems (2)

v2 of 3 Superseded Latest is v3 →

lore
Share & tools
lore
#0 lore raw

v2 cover power: supply: bq25890: fix and extend

This series consists of a set of fixes and enchancements to bq25890 driver. This is tested on a board using bq25896 as battery controller.

Patches 1-3 are cleans up the code a bit, 4-6 fix property value reading, 7-9 add more information to be read from the chip, 10-11 add IBAT compensation support.

v2 removes VBUS and VSYS additions (they need more intrusive changes to properly fit into power supply class ABI) and adds binding description to IBAT compensation devicetree properties.

Michał Mirosław (11):
power: bq25890: remove redundant I2C bus check
power: bq25890: simplify chip name property getter
power: bq25890: make property table const
power: bq25890: protect view of the chip's state
power: bq25890: fix ADC mode configuration
power: bq25890: update state on property read
power: bq25890: implement CHARGE_TYPE property
power: bq25890: implement PRECHARGE_CURRENT property
power: bq25890: implement INPUT_CURRENT_LIMIT property
power: bq25890: support IBAT compensation
power: bq25890: document IBAT compensation DT properties

 .../bindings/power/supply/bq25890.txt         |   4 +
 drivers/power/supply/bq25890_charger.c        | 190 ++++++++++--------
 2 files changed, 113 insertions(+), 81 deletions(-)
Signature · 1 line
2.20.1
#1 lore raw

PATCH v2 1/11 power: bq25890: remove redundant I2C bus check

regmap initialization will check I2C adapter functionality. Remove redundant check in the driver.

---
 drivers/power/supply/bq25890_charger.c | 6 ------
 1 file changed, 6 deletions(-)
drivers/power/supply/bq25890_charger.c +0 -6
index aebd1253dbc9..c642519ef7b2 100644
@@ -881,17 +881,11 @@ static int bq25890_fw_probe(struct bq25890_device *bq)
 static int bq25890_probe(struct i2c_client *client,
 			 const struct i2c_device_id *id)
 {
-	struct i2c_adapter *adapter = client->adapter;
 	struct device *dev = &client->dev;
 	struct bq25890_device *bq;
 	int ret;
 	int i;
 
-	if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) {
-		dev_err(dev, "No support for SMBUS_BYTE_DATA\n");
-		return -ENODEV;
-	}
-
 	bq = devm_kzalloc(dev, sizeof(*bq), GFP_KERNEL);
 	if (!bq)
 		return -ENOMEM;
Signature · 1 line
2.20.1
#2 lore raw

Re: [PATCH v2 01/11] power: bq25890: remove redundant I2C bus check

Hi,

Quoted 5 lines · Michał Mirosław

regmap initialization will check I2C adapter functionality. Remove redundant check in the driver.

---

Thanks, queued.

-- Sebastian

Quoted 28 lines
 drivers/power/supply/bq25890_charger.c | 6 ------
 1 file changed, 6 deletions(-)
drivers/power/supply/bq25890_charger.c +0 -6
index aebd1253dbc9..c642519ef7b2 100644
@@ -881,17 +881,11 @@ static int bq25890_fw_probe(struct bq25890_device *bq)
 static int bq25890_probe(struct i2c_client *client,
 			 const struct i2c_device_id *id)
 {
-	struct i2c_adapter *adapter = client->adapter;
 	struct device *dev = &client->dev;
 	struct bq25890_device *bq;
 	int ret;
 	int i;
 
-	if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) {
-		dev_err(dev, "No support for SMBUS_BYTE_DATA\n");
-		return -ENODEV;
-	}
-
 	bq = devm_kzalloc(dev, sizeof(*bq), GFP_KERNEL);
 	if (!bq)
 		return -ENOMEM;
Signature · 1 line
2.20.1
#3 lore raw

PATCH v2 2/11 power: bq25890: simplify chip name property getter

In reply to Michał Mirosław

Driver rejects unknown chips early in the probe(), so when bq25890_power_supply_get_property() is made reachable, bq->chip_version will already be set to correct value - there is no need to check it again.

---
 drivers/power/supply/bq25890_charger.c | 19 ++++++++-----------
 1 file changed, 8 insertions(+), 11 deletions(-)
drivers/power/supply/bq25890_charger.c +8 -11
index c642519ef7b2..f9f29edadddc 100644
@@ -32,6 +32,13 @@ enum bq25890_chip_version {
 	BQ25896,
 };
 
+static const char *const bq25890_chip_name[] = {
+	"BQ25890",
+	"BQ25892",
+	"BQ25895",
+	"BQ25896",
+};
+
 enum bq25890_fields {
 	F_EN_HIZ, F_EN_ILIM, F_IILIM,				     /* Reg00 */
 	F_BHOT, F_BCOLD, F_VINDPM_OFS,				     /* Reg01 */
@@ -400,17 +407,7 @@ static int bq25890_power_supply_get_property(struct power_supply *psy,
 		break;
 
 	case POWER_SUPPLY_PROP_MODEL_NAME:
-		if (bq->chip_version == BQ25890)
-			val->strval = "BQ25890";
-		else if (bq->chip_version == BQ25892)
-			val->strval = "BQ25892";
-		else if (bq->chip_version == BQ25895)
-			val->strval = "BQ25895";
-		else if (bq->chip_version == BQ25896)
-			val->strval = "BQ25896";
-		else
-			val->strval = "UNKNOWN";
-
+		val->strval = bq25890_chip_name[bq->chip_version];
 		break;
 
 	case POWER_SUPPLY_PROP_ONLINE:
Signature · 1 line
2.20.1
#4 lore raw

Re: [PATCH v2 02/11] power: bq25890: simplify chip name property getter

Hi,

Quoted 7 lines · Michał Mirosław

Driver rejects unknown chips early in the probe(), so when bq25890_power_supply_get_property() is made reachable, bq->chip_version will already be set to correct value - there is no need to check it again.

---

Thanks, queued.

-- Sebastian

Quoted 43 lines
 drivers/power/supply/bq25890_charger.c | 19 ++++++++-----------
 1 file changed, 8 insertions(+), 11 deletions(-)
drivers/power/supply/bq25890_charger.c +8 -11
index c642519ef7b2..f9f29edadddc 100644
@@ -32,6 +32,13 @@ enum bq25890_chip_version {
 	BQ25896,
 };
 
+static const char *const bq25890_chip_name[] = {
+	"BQ25890",
+	"BQ25892",
+	"BQ25895",
+	"BQ25896",
+};
+
 enum bq25890_fields {
 	F_EN_HIZ, F_EN_ILIM, F_IILIM,				     /* Reg00 */
 	F_BHOT, F_BCOLD, F_VINDPM_OFS,				     /* Reg01 */
@@ -400,17 +407,7 @@ static int bq25890_power_supply_get_property(struct power_supply *psy,
 		break;
 
 	case POWER_SUPPLY_PROP_MODEL_NAME:
-		if (bq->chip_version == BQ25890)
-			val->strval = "BQ25890";
-		else if (bq->chip_version == BQ25892)
-			val->strval = "BQ25892";
-		else if (bq->chip_version == BQ25895)
-			val->strval = "BQ25895";
-		else if (bq->chip_version == BQ25896)
-			val->strval = "BQ25896";
-		else
-			val->strval = "UNKNOWN";
-
+		val->strval = bq25890_chip_name[bq->chip_version];
 		break;
 
 	case POWER_SUPPLY_PROP_ONLINE:
Signature · 1 line
2.20.1
#5 lore raw

PATCH v2 3/11 power: bq25890: make property table const

In reply to Michał Mirosław

Property list should not change, so mark it const.

---
 drivers/power/supply/bq25890_charger.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/power/supply/bq25890_charger.c +1 -1
index f9f29edadddc..c4a69fd69f34 100644
@@ -668,7 +668,7 @@ static int bq25890_hw_init(struct bq25890_device *bq)
 	return 0;
 }
 
-static enum power_supply_property bq25890_power_supply_props[] = {
+static const enum power_supply_property bq25890_power_supply_props[] = {
 	POWER_SUPPLY_PROP_MANUFACTURER,
 	POWER_SUPPLY_PROP_MODEL_NAME,
 	POWER_SUPPLY_PROP_STATUS,
Signature · 1 line
2.20.1
#6 lore raw

Re: [PATCH v2 03/11] power: bq25890: make property table const

Hi,

Quoted 4 lines · Michał Mirosław

Property list should not change, so mark it const.

---

Thanks, queued.

-- Sebastian

Quoted 19 lines
 drivers/power/supply/bq25890_charger.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/power/supply/bq25890_charger.c +1 -1
index f9f29edadddc..c4a69fd69f34 100644
@@ -668,7 +668,7 @@ static int bq25890_hw_init(struct bq25890_device *bq)
 	return 0;
 }
 
-static enum power_supply_property bq25890_power_supply_props[] = {
+static const enum power_supply_property bq25890_power_supply_props[] = {
 	POWER_SUPPLY_PROP_MANUFACTURER,
 	POWER_SUPPLY_PROP_MODEL_NAME,
 	POWER_SUPPLY_PROP_STATUS,
Signature · 1 line
2.20.1
#7 lore raw

PATCH v2 4/11 power: bq25890: protect view of the chip's state

In reply to Michał Mirosław

Extend bq->lock over whole updating of the chip's state. Might get useful later for switching ADC modes correctly.

---
 drivers/power/supply/bq25890_charger.c | 82 ++++++++------------------
 1 file changed, 26 insertions(+), 56 deletions(-)
drivers/power/supply/bq25890_charger.c +26 -56
index c4a69fd69f34..9339e216651f 100644
@@ -510,74 +510,50 @@ static int bq25890_get_chip_state(struct bq25890_device *bq,
 	return 0;
 }
 
-static bool bq25890_state_changed(struct bq25890_device *bq,
-				  struct bq25890_state *new_state)
-{
-	struct bq25890_state old_state;
-
-	mutex_lock(&bq->lock);
-	old_state = bq->state;
-	mutex_unlock(&bq->lock);
-
-	return (old_state.chrg_status != new_state->chrg_status ||
-		old_state.chrg_fault != new_state->chrg_fault	||
-		old_state.online != new_state->online		||
-		old_state.bat_fault != new_state->bat_fault	||
-		old_state.boost_fault != new_state->boost_fault ||
-		old_state.vsys_status != new_state->vsys_status);
-}
-
-static void bq25890_handle_state_change(struct bq25890_device *bq,
-					struct bq25890_state *new_state)
+static irqreturn_t __bq25890_handle_irq(struct bq25890_device *bq)
 {
+	struct bq25890_state new_state;
 	int ret;
-	struct bq25890_state old_state;
 
-	mutex_lock(&bq->lock);
-	old_state = bq->state;
-	mutex_unlock(&bq->lock);
+	ret = bq25890_get_chip_state(bq, &new_state);
+	if (ret < 0)
+		return IRQ_NONE;
 
-	if (!new_state->online) {			     /* power removed */
+	if (!memcmp(&bq->state, &new_state, sizeof(new_state)))
+		return IRQ_NONE;
+
+	if (!new_state.online && bq->state.online) {	    /* power removed */
 		/* disable ADC */
 		ret = bq25890_field_write(bq, F_CONV_START, 0);
 		if (ret < 0)
 			goto error;
-	} else if (!old_state.online) {			    /* power inserted */
+	} else if (new_state.online && !bq->state.online) { /* power inserted */
 		/* enable ADC, to have control of charge current/voltage */
 		ret = bq25890_field_write(bq, F_CONV_START, 1);
 		if (ret < 0)
 			goto error;
 	}
 
-	return;
+	bq->state = new_state;
+	power_supply_changed(bq->charger);
 
+	return IRQ_HANDLED;
 error:
-	dev_err(bq->dev, "Error communicating with the chip.\n");
+	dev_err(bq->dev, "Error communicating with the chip: %pe\n",
+		ERR_PTR(ret));
+	return IRQ_HANDLED;
 }
 
 static irqreturn_t bq25890_irq_handler_thread(int irq, void *private)
 {
 	struct bq25890_device *bq = private;
-	int ret;
-	struct bq25890_state state;
-
-	ret = bq25890_get_chip_state(bq, &state);
-	if (ret < 0)
-		goto handled;
-
-	if (!bq25890_state_changed(bq, &state))
-		goto handled;
-
-	bq25890_handle_state_change(bq, &state);
+	irqreturn_t ret;
 
 	mutex_lock(&bq->lock);
-	bq->state = state;
+	ret = __bq25890_handle_irq(bq);
 	mutex_unlock(&bq->lock);
 
-	power_supply_changed(bq->charger);
-
-handled:
-	return IRQ_HANDLED;
+	return ret;
 }
 
 static int bq25890_chip_reset(struct bq25890_device *bq)
@@ -607,7 +583,6 @@ static int bq25890_hw_init(struct bq25890_device *bq)
 {
 	int ret;
 	int i;
-	struct bq25890_state state;
 
 	const struct {
 		enum bq25890_fields id;
@@ -655,16 +630,12 @@ static int bq25890_hw_init(struct bq25890_device *bq)
 		return ret;
 	}
 
-	ret = bq25890_get_chip_state(bq, &state);
+	ret = bq25890_get_chip_state(bq, &bq->state);
 	if (ret < 0) {
 		dev_dbg(bq->dev, "Get state failed %d\n", ret);
 		return ret;
 	}
 
-	mutex_lock(&bq->lock);
-	bq->state = state;
-	mutex_unlock(&bq->lock);
-
 	return 0;
 }
 
@@ -1001,19 +972,16 @@ static int bq25890_suspend(struct device *dev)
 static int bq25890_resume(struct device *dev)
 {
 	int ret;
-	struct bq25890_state state;
 	struct bq25890_device *bq = dev_get_drvdata(dev);
 
-	ret = bq25890_get_chip_state(bq, &state);
+	mutex_lock(&bq->lock);
+
+	ret = bq25890_get_chip_state(bq, &bq->state);
 	if (ret < 0)
 		return ret;
 
-	mutex_lock(&bq->lock);
-	bq->state = state;
-	mutex_unlock(&bq->lock);
-
 	/* Re-enable ADC only if charger is plugged in. */
-	if (state.online) {
+	if (bq->state.online) {
 		ret = bq25890_field_write(bq, F_CONV_START, 1);
 		if (ret < 0)
 			return ret;
@@ -1022,6 +990,8 @@ static int bq25890_resume(struct device *dev)
 	/* signal userspace, maybe state changed while suspended */
 	power_supply_changed(bq->charger);
 
+	mutex_unlock(&bq->lock);
+
 	return 0;
 }
 #endif
Signature · 1 line
2.20.1
#8 lore raw

Re: [PATCH v2 04/11] power: bq25890: protect view of the chip's state

Hi,

Quoted 5 lines · Michał Mirosław

Extend bq->lock over whole updating of the chip's state. Might get useful later for switching ADC modes correctly.

---

Thanks, queued.

-- Sebastian

Quoted 163 lines
 drivers/power/supply/bq25890_charger.c | 82 ++++++++------------------
 1 file changed, 26 insertions(+), 56 deletions(-)
drivers/power/supply/bq25890_charger.c +26 -56
index c4a69fd69f34..9339e216651f 100644
@@ -510,74 +510,50 @@ static int bq25890_get_chip_state(struct bq25890_device *bq,
 	return 0;
 }
 
-static bool bq25890_state_changed(struct bq25890_device *bq,
-				  struct bq25890_state *new_state)
-{
-	struct bq25890_state old_state;
-
-	mutex_lock(&bq->lock);
-	old_state = bq->state;
-	mutex_unlock(&bq->lock);
-
-	return (old_state.chrg_status != new_state->chrg_status ||
-		old_state.chrg_fault != new_state->chrg_fault	||
-		old_state.online != new_state->online		||
-		old_state.bat_fault != new_state->bat_fault	||
-		old_state.boost_fault != new_state->boost_fault ||
-		old_state.vsys_status != new_state->vsys_status);
-}
-
-static void bq25890_handle_state_change(struct bq25890_device *bq,
-					struct bq25890_state *new_state)
+static irqreturn_t __bq25890_handle_irq(struct bq25890_device *bq)
 {
+	struct bq25890_state new_state;
 	int ret;
-	struct bq25890_state old_state;
 
-	mutex_lock(&bq->lock);
-	old_state = bq->state;
-	mutex_unlock(&bq->lock);
+	ret = bq25890_get_chip_state(bq, &new_state);
+	if (ret < 0)
+		return IRQ_NONE;
 
-	if (!new_state->online) {			     /* power removed */
+	if (!memcmp(&bq->state, &new_state, sizeof(new_state)))
+		return IRQ_NONE;
+
+	if (!new_state.online && bq->state.online) {	    /* power removed */
 		/* disable ADC */
 		ret = bq25890_field_write(bq, F_CONV_START, 0);
 		if (ret < 0)
 			goto error;
-	} else if (!old_state.online) {			    /* power inserted */
+	} else if (new_state.online && !bq->state.online) { /* power inserted */
 		/* enable ADC, to have control of charge current/voltage */
 		ret = bq25890_field_write(bq, F_CONV_START, 1);
 		if (ret < 0)
 			goto error;
 	}
 
-	return;
+	bq->state = new_state;
+	power_supply_changed(bq->charger);
 
+	return IRQ_HANDLED;
 error:
-	dev_err(bq->dev, "Error communicating with the chip.\n");
+	dev_err(bq->dev, "Error communicating with the chip: %pe\n",
+		ERR_PTR(ret));
+	return IRQ_HANDLED;
 }
 
 static irqreturn_t bq25890_irq_handler_thread(int irq, void *private)
 {
 	struct bq25890_device *bq = private;
-	int ret;
-	struct bq25890_state state;
-
-	ret = bq25890_get_chip_state(bq, &state);
-	if (ret < 0)
-		goto handled;
-
-	if (!bq25890_state_changed(bq, &state))
-		goto handled;
-
-	bq25890_handle_state_change(bq, &state);
+	irqreturn_t ret;
 
 	mutex_lock(&bq->lock);
-	bq->state = state;
+	ret = __bq25890_handle_irq(bq);
 	mutex_unlock(&bq->lock);
 
-	power_supply_changed(bq->charger);
-
-handled:
-	return IRQ_HANDLED;
+	return ret;
 }
 
 static int bq25890_chip_reset(struct bq25890_device *bq)
@@ -607,7 +583,6 @@ static int bq25890_hw_init(struct bq25890_device *bq)
 {
 	int ret;
 	int i;
-	struct bq25890_state state;
 
 	const struct {
 		enum bq25890_fields id;
@@ -655,16 +630,12 @@ static int bq25890_hw_init(struct bq25890_device *bq)
 		return ret;
 	}
 
-	ret = bq25890_get_chip_state(bq, &state);
+	ret = bq25890_get_chip_state(bq, &bq->state);
 	if (ret < 0) {
 		dev_dbg(bq->dev, "Get state failed %d\n", ret);
 		return ret;
 	}
 
-	mutex_lock(&bq->lock);
-	bq->state = state;
-	mutex_unlock(&bq->lock);
-
 	return 0;
 }
 
@@ -1001,19 +972,16 @@ static int bq25890_suspend(struct device *dev)
 static int bq25890_resume(struct device *dev)
 {
 	int ret;
-	struct bq25890_state state;
 	struct bq25890_device *bq = dev_get_drvdata(dev);
 
-	ret = bq25890_get_chip_state(bq, &state);
+	mutex_lock(&bq->lock);
+
+	ret = bq25890_get_chip_state(bq, &bq->state);
 	if (ret < 0)
 		return ret;
 
-	mutex_lock(&bq->lock);
-	bq->state = state;
-	mutex_unlock(&bq->lock);
-
 	/* Re-enable ADC only if charger is plugged in. */
-	if (state.online) {
+	if (bq->state.online) {
 		ret = bq25890_field_write(bq, F_CONV_START, 1);
 		if (ret < 0)
 			return ret;
@@ -1022,6 +990,8 @@ static int bq25890_resume(struct device *dev)
 	/* signal userspace, maybe state changed while suspended */
 	power_supply_changed(bq->charger);
 
+	mutex_unlock(&bq->lock);
+
 	return 0;
 }
 #endif
Signature · 1 line
2.20.1
#9 lore raw

PATCH v2 5/11 power: bq25890: fix ADC mode configuration

In reply to Michał Mirosław

Datasheet describes two modes for reading ADC measurements:
1. continuous, 1 Hz - enabled and started by CONV_RATE bit
2. one-shot - triggered by CONV_START bit

In continuous mode, CONV_START is read-only and signifies an ongoing conversion.

Change the code to follow the datasheet and really disable continuous mode for power saving.

---
 drivers/power/supply/bq25890_charger.c | 33 ++++++++++++++++++++++----
 1 file changed, 28 insertions(+), 5 deletions(-)
drivers/power/supply/bq25890_charger.c +28 -5
index 9339e216651f..3b02fa80aedd 100644
@@ -126,6 +126,7 @@ static const struct regmap_access_table bq25890_writeable_regs = {
 
 static const struct regmap_range bq25890_volatile_reg_ranges[] = {
 	regmap_reg_range(0x00, 0x00),
+	regmap_reg_range(0x02, 0x02),
 	regmap_reg_range(0x09, 0x09),
 	regmap_reg_range(0x0b, 0x14),
 };
@@ -374,18 +375,40 @@ enum bq25890_chrg_fault {
 	CHRG_FAULT_TIMER_EXPIRED,
 };
 
+static bool bq25890_is_adc_property(enum power_supply_property psp)
+{
+	switch (psp) {
+	case POWER_SUPPLY_PROP_INPUT_VOLTAGE_NOW:
+	case POWER_SUPPLY_PROP_OUTPUT_VOLTAGE_NOW:
+	case POWER_SUPPLY_PROP_VOLTAGE_NOW:
+	case POWER_SUPPLY_PROP_CURRENT_NOW:
+		return true;
+
+	default:
+		return false;
+	}
+}
+
 static int bq25890_power_supply_get_property(struct power_supply *psy,
 					     enum power_supply_property psp,
 					     union power_supply_propval *val)
 {
-	int ret;
 	struct bq25890_device *bq = power_supply_get_drvdata(psy);
 	struct bq25890_state state;
+	bool do_adc_conv;
+	int ret;
 
 	mutex_lock(&bq->lock);
 	state = bq->state;
+	do_adc_conv = !state.online && bq25890_is_adc_property(psp);
+	if (do_adc_conv)
+		bq25890_field_write(bq, F_CONV_START, 1);
 	mutex_unlock(&bq->lock);
 
+	if (do_adc_conv)
+		regmap_field_read_poll_timeout(bq->rmap_fields[F_CONV_START],
+			ret, !ret, 25000, 1000000);
+
 	switch (psp) {
 	case POWER_SUPPLY_PROP_STATUS:
 		if (!state.online)
@@ -623,8 +646,8 @@ static int bq25890_hw_init(struct bq25890_device *bq)
 		}
 	}
 
-	/* Configure ADC for continuous conversions. This does not enable it. */
-	ret = bq25890_field_write(bq, F_CONV_RATE, 1);
+	/* Configure ADC for continuous conversions when charging */
+	ret = bq25890_field_write(bq, F_CONV_RATE, !!bq->state.online);
 	if (ret < 0) {
 		dev_dbg(bq->dev, "Config ADC failed %d\n", ret);
 		return ret;
@@ -966,7 +989,7 @@ static int bq25890_suspend(struct device *dev)
 	 * If charger is removed, while in suspend, make sure ADC is diabled
 	 * since it consumes slightly more power.
 	 */
-	return bq25890_field_write(bq, F_CONV_START, 0);
+	return bq25890_field_write(bq, F_CONV_RATE, 0);
 }
 
 static int bq25890_resume(struct device *dev)
@@ -982,7 +1005,7 @@ static int bq25890_resume(struct device *dev)
 
 	/* Re-enable ADC only if charger is plugged in. */
 	if (bq->state.online) {
-		ret = bq25890_field_write(bq, F_CONV_START, 1);
+		ret = bq25890_field_write(bq, F_CONV_RATE, 1);
 		if (ret < 0)
 			return ret;
 	}
Signature · 1 line
2.20.1
#10 lore raw

Re: [PATCH v2 05/11] power: bq25890: fix ADC mode configuration

Hi,

Quoted 28 lines · Michał Mirosław

Datasheet describes two modes for reading ADC measurements:
1. continuous, 1 Hz - enabled and started by CONV_RATE bit
2. one-shot - triggered by CONV_START bit

In continuous mode, CONV_START is read-only and signifies an ongoing conversion.

Change the code to follow the datasheet and really disable continuous mode for power saving.

---
 drivers/power/supply/bq25890_charger.c | 33 ++++++++++++++++++++++----
 1 file changed, 28 insertions(+), 5 deletions(-)
drivers/power/supply/bq25890_charger.c +1 -0
index 9339e216651f..3b02fa80aedd 100644
@@ -126,6 +126,7 @@ static const struct regmap_access_table bq25890_writeable_regs = {
 
 static const struct regmap_range bq25890_volatile_reg_ranges[] = {
 	regmap_reg_range(0x00, 0x00),
+	regmap_reg_range(0x02, 0x02),
 	regmap_reg_range(0x09, 0x09),
 	regmap_reg_range(0x0b, 0x14),
 };

drivers/power/supply/bq25890_charger.c enum bq25890_chrg_fault { · line 382

Quoted 8 lines
drivers/power/supply/bq25890_charger.c +5 -0
@@ -374,18 +375,40 @@ enum bq25890_chrg_fault {
 	CHRG_FAULT_TIMER_EXPIRED,
 };
 
+static bool bq25890_is_adc_property(enum power_supply_property psp)
+{
+	switch (psp) {
+	case POWER_SUPPLY_PROP_INPUT_VOLTAGE_NOW:
+	case POWER_SUPPLY_PROP_OUTPUT_VOLTAGE_NOW:

^^^ does not compile without your other patchset, so not applied.

When you send a new version, please Cc some of the recent contributors to bq25890_charger.c, so that they have a chance to test the changes with their setup:

Angus Ainslie (Purism) <[email protected]>
Yauhen Kharuzhy <[email protected]>

-- Sebastian

Quoted 65 lines
drivers/power/supply/bq25890_charger.c +22 -5
+	case POWER_SUPPLY_PROP_VOLTAGE_NOW:
+	case POWER_SUPPLY_PROP_CURRENT_NOW:
+		return true;
+
+	default:
+		return false;
+	}
+}
+
 static int bq25890_power_supply_get_property(struct power_supply *psy,
 					     enum power_supply_property psp,
 					     union power_supply_propval *val)
 {
-	int ret;
 	struct bq25890_device *bq = power_supply_get_drvdata(psy);
 	struct bq25890_state state;
+	bool do_adc_conv;
+	int ret;
 
 	mutex_lock(&bq->lock);
 	state = bq->state;
+	do_adc_conv = !state.online && bq25890_is_adc_property(psp);
+	if (do_adc_conv)
+		bq25890_field_write(bq, F_CONV_START, 1);
 	mutex_unlock(&bq->lock);
 
+	if (do_adc_conv)
+		regmap_field_read_poll_timeout(bq->rmap_fields[F_CONV_START],
+			ret, !ret, 25000, 1000000);
+
 	switch (psp) {
 	case POWER_SUPPLY_PROP_STATUS:
 		if (!state.online)
@@ -623,8 +646,8 @@ static int bq25890_hw_init(struct bq25890_device *bq)
 		}
 	}
 
-	/* Configure ADC for continuous conversions. This does not enable it. */
-	ret = bq25890_field_write(bq, F_CONV_RATE, 1);
+	/* Configure ADC for continuous conversions when charging */
+	ret = bq25890_field_write(bq, F_CONV_RATE, !!bq->state.online);
 	if (ret < 0) {
 		dev_dbg(bq->dev, "Config ADC failed %d\n", ret);
 		return ret;
@@ -966,7 +989,7 @@ static int bq25890_suspend(struct device *dev)
 	 * If charger is removed, while in suspend, make sure ADC is diabled
 	 * since it consumes slightly more power.
 	 */
-	return bq25890_field_write(bq, F_CONV_START, 0);
+	return bq25890_field_write(bq, F_CONV_RATE, 0);
 }
 
 static int bq25890_resume(struct device *dev)
@@ -982,7 +1005,7 @@ static int bq25890_resume(struct device *dev)
 
 	/* Re-enable ADC only if charger is plugged in. */
 	if (bq->state.online) {
-		ret = bq25890_field_write(bq, F_CONV_START, 1);
+		ret = bq25890_field_write(bq, F_CONV_RATE, 1);
 		if (ret < 0)
 			return ret;
 	}
Signature · 1 line
2.20.1
#11 lore raw

PATCH v2 6/11 power: bq25890: update state on property read

In reply to Michał Mirosław

Edge interrupts from the charger may be lost or stuck in fault mode since probe(). Check if something changed everytime userspace wants some data.

---
 drivers/power/supply/bq25890_charger.c | 4 ++++
 1 file changed, 4 insertions(+)
drivers/power/supply/bq25890_charger.c +4 -0
index 3b02fa80aedd..e4368d01396a 100644
@@ -389,6 +389,8 @@ static bool bq25890_is_adc_property(enum power_supply_property psp)
 	}
 }
 
+static irqreturn_t __bq25890_handle_irq(struct bq25890_device *bq);
+
 static int bq25890_power_supply_get_property(struct power_supply *psy,
 					     enum power_supply_property psp,
 					     union power_supply_propval *val)
@@ -399,6 +401,8 @@ static int bq25890_power_supply_get_property(struct power_supply *psy,
 	int ret;
 
 	mutex_lock(&bq->lock);
+	/* update state in case we lost an interrupt */
+	__bq25890_handle_irq(bq);
 	state = bq->state;
 	do_adc_conv = !state.online && bq25890_is_adc_property(psp);
 	if (do_adc_conv)
Signature · 1 line
2.20.1
Reviewed-by on v2 6/11
#12 lore raw

Re: [PATCH v2 06/11] power: bq25890: update state on property read

Hi,

Quoted 6 lines · Michał Mirosław

Edge interrupts from the charger may be lost or stuck in fault mode since probe(). Check if something changed everytime userspace wants some data.

---

-- Sebastian

Quoted 28 lines
 drivers/power/supply/bq25890_charger.c | 4 ++++
 1 file changed, 4 insertions(+)
drivers/power/supply/bq25890_charger.c +4 -0
index 3b02fa80aedd..e4368d01396a 100644
@@ -389,6 +389,8 @@ static bool bq25890_is_adc_property(enum power_supply_property psp)
 	}
 }
 
+static irqreturn_t __bq25890_handle_irq(struct bq25890_device *bq);
+
 static int bq25890_power_supply_get_property(struct power_supply *psy,
 					     enum power_supply_property psp,
 					     union power_supply_propval *val)
@@ -399,6 +401,8 @@ static int bq25890_power_supply_get_property(struct power_supply *psy,
 	int ret;
 
 	mutex_lock(&bq->lock);
+	/* update state in case we lost an interrupt */
+	__bq25890_handle_irq(bq);
 	state = bq->state;
 	do_adc_conv = !state.online && bq25890_is_adc_property(psp);
 	if (do_adc_conv)
Signature · 1 line
2.20.1
#13 lore raw

PATCH v2 7/11 power: bq25890: implement CHARGE_TYPE property

In reply to Michał Mirosław

Report charging type based on recently read state.

---
 drivers/power/supply/bq25890_charger.c | 13 +++++++++++++
 1 file changed, 13 insertions(+)
drivers/power/supply/bq25890_charger.c +13 -0
index e4368d01396a..ad0901fdceb6 100644
@@ -429,6 +429,18 @@ static int bq25890_power_supply_get_property(struct power_supply *psy,
 
 		break;
 
+	case POWER_SUPPLY_PROP_CHARGE_TYPE:
+		if (!state.online || state.chrg_status == STATUS_NOT_CHARGING ||
+		    state.chrg_status == STATUS_TERMINATION_DONE)
+			val->intval = POWER_SUPPLY_CHARGE_TYPE_NONE;
+		else if (state.chrg_status == STATUS_PRE_CHARGING)
+			val->intval = POWER_SUPPLY_CHARGE_TYPE_STANDARD;
+		else if (state.chrg_status == STATUS_FAST_CHARGING)
+			val->intval = POWER_SUPPLY_CHARGE_TYPE_FAST;
+		else /* unreachable */
+			val->intval = POWER_SUPPLY_CHARGE_TYPE_UNKNOWN;
+		break;
+
 	case POWER_SUPPLY_PROP_MANUFACTURER:
 		val->strval = BQ25890_MANUFACTURER;
 		break;
@@ -670,6 +682,7 @@ static const enum power_supply_property bq25890_power_supply_props[] = {
 	POWER_SUPPLY_PROP_MANUFACTURER,
 	POWER_SUPPLY_PROP_MODEL_NAME,
 	POWER_SUPPLY_PROP_STATUS,
+	POWER_SUPPLY_PROP_CHARGE_TYPE,
 	POWER_SUPPLY_PROP_ONLINE,
 	POWER_SUPPLY_PROP_HEALTH,
 	POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT,
Signature · 1 line
2.20.1
Reviewed-by on v2 7/11
#14 lore raw

Re: [PATCH v2 07/11] power: bq25890: implement CHARGE_TYPE property

Hi,

Quoted 4 lines · Michał Mirosław

Report charging type based on recently read state.

---

-- Sebastian

Quoted 37 lines
 drivers/power/supply/bq25890_charger.c | 13 +++++++++++++
 1 file changed, 13 insertions(+)
drivers/power/supply/bq25890_charger.c +13 -0
index e4368d01396a..ad0901fdceb6 100644
@@ -429,6 +429,18 @@ static int bq25890_power_supply_get_property(struct power_supply *psy,
 
 		break;
 
+	case POWER_SUPPLY_PROP_CHARGE_TYPE:
+		if (!state.online || state.chrg_status == STATUS_NOT_CHARGING ||
+		    state.chrg_status == STATUS_TERMINATION_DONE)
+			val->intval = POWER_SUPPLY_CHARGE_TYPE_NONE;
+		else if (state.chrg_status == STATUS_PRE_CHARGING)
+			val->intval = POWER_SUPPLY_CHARGE_TYPE_STANDARD;
+		else if (state.chrg_status == STATUS_FAST_CHARGING)
+			val->intval = POWER_SUPPLY_CHARGE_TYPE_FAST;
+		else /* unreachable */
+			val->intval = POWER_SUPPLY_CHARGE_TYPE_UNKNOWN;
+		break;
+
 	case POWER_SUPPLY_PROP_MANUFACTURER:
 		val->strval = BQ25890_MANUFACTURER;
 		break;
@@ -670,6 +682,7 @@ static const enum power_supply_property bq25890_power_supply_props[] = {
 	POWER_SUPPLY_PROP_MANUFACTURER,
 	POWER_SUPPLY_PROP_MODEL_NAME,
 	POWER_SUPPLY_PROP_STATUS,
+	POWER_SUPPLY_PROP_CHARGE_TYPE,
 	POWER_SUPPLY_PROP_ONLINE,
 	POWER_SUPPLY_PROP_HEALTH,
 	POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT,
Signature · 1 line
2.20.1
#15 lore raw

PATCH v2 8/11 power: bq25890: implement PRECHARGE_CURRENT property

In reply to Michał Mirosław

Report configured precharge current.

---
 drivers/power/supply/bq25890_charger.c | 5 +++++
 1 file changed, 5 insertions(+)
drivers/power/supply/bq25890_charger.c +5 -0
index ad0901fdceb6..b48685009048 100644
@@ -497,6 +497,10 @@ static int bq25890_power_supply_get_property(struct power_supply *psy,
 		val->intval = bq25890_find_val(bq->init_data.vreg, TBL_VREG);
 		break;
 
+	case POWER_SUPPLY_PROP_PRECHARGE_CURRENT:
+		val->intval = bq25890_find_val(bq->init_data.iprechg, TBL_ITERM);
+		break;
+
 	case POWER_SUPPLY_PROP_CHARGE_TERM_CURRENT:
 		val->intval = bq25890_find_val(bq->init_data.iterm, TBL_ITERM);
 		break;
@@ -689,6 +693,7 @@ static const enum power_supply_property bq25890_power_supply_props[] = {
 	POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX,
 	POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE,
 	POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE_MAX,
+	POWER_SUPPLY_PROP_PRECHARGE_CURRENT,
 	POWER_SUPPLY_PROP_CHARGE_TERM_CURRENT,
 	POWER_SUPPLY_PROP_VOLTAGE_NOW,
 };
Signature · 1 line
2.20.1
Reviewed-by on v2 8/11
#16 lore raw

Re: [PATCH v2 08/11] power: bq25890: implement PRECHARGE_CURRENT property

Hi,

Quoted 4 lines · Michał Mirosław

Report configured precharge current.

---

-- Sebastian

Quoted 29 lines
 drivers/power/supply/bq25890_charger.c | 5 +++++
 1 file changed, 5 insertions(+)
drivers/power/supply/bq25890_charger.c +5 -0
index ad0901fdceb6..b48685009048 100644
@@ -497,6 +497,10 @@ static int bq25890_power_supply_get_property(struct power_supply *psy,
 		val->intval = bq25890_find_val(bq->init_data.vreg, TBL_VREG);
 		break;
 
+	case POWER_SUPPLY_PROP_PRECHARGE_CURRENT:
+		val->intval = bq25890_find_val(bq->init_data.iprechg, TBL_ITERM);
+		break;
+
 	case POWER_SUPPLY_PROP_CHARGE_TERM_CURRENT:
 		val->intval = bq25890_find_val(bq->init_data.iterm, TBL_ITERM);
 		break;
@@ -689,6 +693,7 @@ static const enum power_supply_property bq25890_power_supply_props[] = {
 	POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX,
 	POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE,
 	POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE_MAX,
+	POWER_SUPPLY_PROP_PRECHARGE_CURRENT,
 	POWER_SUPPLY_PROP_CHARGE_TERM_CURRENT,
 	POWER_SUPPLY_PROP_VOLTAGE_NOW,
 };
Signature · 1 line
2.20.1
#17 lore raw

PATCH v2 9/11 power: bq25890: implement INPUT_CURRENT_LIMIT property

In reply to Michał Mirosław

Report REG00.IINLIM value as INPUT_CURRENT_LIMIT property.

---
 drivers/power/supply/bq25890_charger.c | 11 +++++++++++
 1 file changed, 11 insertions(+)
drivers/power/supply/bq25890_charger.c +11 -0
index b48685009048..87c5832e23d3 100644
@@ -254,6 +254,7 @@ enum bq25890_table_ids {
 	/* range tables */
 	TBL_ICHG,
 	TBL_ITERM,
+	TBL_IILIM,
 	TBL_VREG,
 	TBL_BOOSTV,
 	TBL_SYSVMIN,
@@ -294,6 +295,7 @@ static const union {
 	/* TODO: BQ25896 has max ICHG 3008 mA */
 	[TBL_ICHG] =	{ .rt = {0,	  5056000, 64000} },	 /* uA */
 	[TBL_ITERM] =	{ .rt = {64000,   1024000, 64000} },	 /* uA */
+	[TBL_IILIM] =   { .rt = {50000,   3200000, 50000} },	 /* uA */
 	[TBL_VREG] =	{ .rt = {3840000, 4608000, 16000} },	 /* uV */
 	[TBL_BOOSTV] =	{ .rt = {4550000, 5510000, 64000} },	 /* uV */
 	[TBL_SYSVMIN] = { .rt = {3000000, 3700000, 100000} },	 /* uV */
@@ -505,6 +507,14 @@ static int bq25890_power_supply_get_property(struct power_supply *psy,
 		val->intval = bq25890_find_val(bq->init_data.iterm, TBL_ITERM);
 		break;
 
+	case POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT:
+		ret = bq25890_field_read(bq, F_IILIM);
+		if (ret < 0)
+			return ret;
+
+		val->intval = bq25890_find_val(ret, TBL_IILIM);
+		break;
+
 	case POWER_SUPPLY_PROP_VOLTAGE_NOW:
 		ret = bq25890_field_read(bq, F_SYSV); /* read measured value */
 		if (ret < 0)
@@ -695,6 +705,7 @@ static const enum power_supply_property bq25890_power_supply_props[] = {
 	POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE_MAX,
 	POWER_SUPPLY_PROP_PRECHARGE_CURRENT,
 	POWER_SUPPLY_PROP_CHARGE_TERM_CURRENT,
+	POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT,
 	POWER_SUPPLY_PROP_VOLTAGE_NOW,
 };
 
Signature · 1 line
2.20.1
Reviewed-by on v2 9/11
#18 lore raw

Re: [PATCH v2 09/11] power: bq25890: implement INPUT_CURRENT_LIMIT property

Hi,

Quoted 4 lines · Michał Mirosław

Report REG00.IINLIM value as INPUT_CURRENT_LIMIT property.

---

-- Sebastian

Quoted 49 lines
 drivers/power/supply/bq25890_charger.c | 11 +++++++++++
 1 file changed, 11 insertions(+)
drivers/power/supply/bq25890_charger.c +11 -0
index b48685009048..87c5832e23d3 100644
@@ -254,6 +254,7 @@ enum bq25890_table_ids {
 	/* range tables */
 	TBL_ICHG,
 	TBL_ITERM,
+	TBL_IILIM,
 	TBL_VREG,
 	TBL_BOOSTV,
 	TBL_SYSVMIN,
@@ -294,6 +295,7 @@ static const union {
 	/* TODO: BQ25896 has max ICHG 3008 mA */
 	[TBL_ICHG] =	{ .rt = {0,	  5056000, 64000} },	 /* uA */
 	[TBL_ITERM] =	{ .rt = {64000,   1024000, 64000} },	 /* uA */
+	[TBL_IILIM] =   { .rt = {50000,   3200000, 50000} },	 /* uA */
 	[TBL_VREG] =	{ .rt = {3840000, 4608000, 16000} },	 /* uV */
 	[TBL_BOOSTV] =	{ .rt = {4550000, 5510000, 64000} },	 /* uV */
 	[TBL_SYSVMIN] = { .rt = {3000000, 3700000, 100000} },	 /* uV */
@@ -505,6 +507,14 @@ static int bq25890_power_supply_get_property(struct power_supply *psy,
 		val->intval = bq25890_find_val(bq->init_data.iterm, TBL_ITERM);
 		break;
 
+	case POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT:
+		ret = bq25890_field_read(bq, F_IILIM);
+		if (ret < 0)
+			return ret;
+
+		val->intval = bq25890_find_val(ret, TBL_IILIM);
+		break;
+
 	case POWER_SUPPLY_PROP_VOLTAGE_NOW:
 		ret = bq25890_field_read(bq, F_SYSV); /* read measured value */
 		if (ret < 0)
@@ -695,6 +705,7 @@ static const enum power_supply_property bq25890_power_supply_props[] = {
 	POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE_MAX,
 	POWER_SUPPLY_PROP_PRECHARGE_CURRENT,
 	POWER_SUPPLY_PROP_CHARGE_TERM_CURRENT,
+	POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT,
 	POWER_SUPPLY_PROP_VOLTAGE_NOW,
 };
 
Signature · 1 line
2.20.1
#19 lore raw

PATCH v2 10/11 power: bq25890: support IBAT compensation

In reply to Michał Mirosław

Add configuration for compensation of IBAT measuring resistor in series with the battery.

---
 drivers/power/supply/bq25890_charger.c | 15 +++++++++++++--
 1 file changed, 13 insertions(+), 2 deletions(-)
drivers/power/supply/bq25890_charger.c +13 -2
index 87c5832e23d3..9d1ba3bd0bea 100644
@@ -83,6 +83,8 @@ struct bq25890_init_data {
 	u8 boostf;	/* boost frequency		*/
 	u8 ilim_en;	/* enable ILIM pin		*/
 	u8 treg;	/* thermal regulation threshold */
+	u8 rbatcomp;	/* IBAT sense resistor value    */
+	u8 vclamp;	/* IBAT compensation voltage limit */
 };
 
 struct bq25890_state {
@@ -258,6 +260,8 @@ enum bq25890_table_ids {
 	TBL_VREG,
 	TBL_BOOSTV,
 	TBL_SYSVMIN,
+	TBL_VBATCOMP,
+	TBL_RBATCOMP,
 
 	/* lookup tables */
 	TBL_TREG,
@@ -299,6 +303,8 @@ static const union {
 	[TBL_VREG] =	{ .rt = {3840000, 4608000, 16000} },	 /* uV */
 	[TBL_BOOSTV] =	{ .rt = {4550000, 5510000, 64000} },	 /* uV */
 	[TBL_SYSVMIN] = { .rt = {3000000, 3700000, 100000} },	 /* uV */
+	[TBL_VBATCOMP] ={ .rt = {0,        224000, 32000} },	 /* uV */
+	[TBL_RBATCOMP] ={ .rt = {0,        140000, 20000} },	 /* uOhm */
 
 	/* lookup tables */
 	[TBL_TREG] =	{ .lt = {bq25890_treg_tbl, BQ25890_TREG_TBL_SIZE} },
@@ -650,7 +656,9 @@ static int bq25890_hw_init(struct bq25890_device *bq)
 		{F_BOOSTI,	 bq->init_data.boosti},
 		{F_BOOSTF,	 bq->init_data.boostf},
 		{F_EN_ILIM,	 bq->init_data.ilim_en},
-		{F_TREG,	 bq->init_data.treg}
+		{F_TREG,	 bq->init_data.treg},
+		{F_BATCMP,	 bq->init_data.rbatcomp},
+		{F_VCLAMP,	 bq->init_data.vclamp},
 	};
 
 	ret = bq25890_chip_reset(bq);
@@ -861,11 +869,14 @@ static int bq25890_fw_read_u32_props(struct bq25890_device *bq)
 		{"ti,boost-max-current", false, TBL_BOOSTI, &init->boosti},
 
 		/* optional properties */
-		{"ti,thermal-regulation-threshold", true, TBL_TREG, &init->treg}
+		{"ti,thermal-regulation-threshold", true, TBL_TREG, &init->treg},
+		{"ti,ibatcomp-resistance", true, TBL_RBATCOMP, &init->rbatcomp},
+		{"ti,ibatcomp-clamp-voltage", true, TBL_VBATCOMP, &init->vclamp},
 	};
 
 	/* initialize data for optional properties */
 	init->treg = 3; /* 120 degrees Celsius */
+	init->rbatcomp = init->vclamp = 0; /* IBAT compensation disabled */
 
 	for (i = 0; i < ARRAY_SIZE(props); i++) {
 		ret = device_property_read_u32(bq->dev, props[i].name,
Signature · 1 line
2.20.1
#20 lore raw

PATCH v2 11/11 power: bq25890: document IBAT compensation DT properties

In reply to Michał Mirosław

Document newly introduced IBAT compensation settings.

---
v2: initial version

---
 Documentation/devicetree/bindings/power/supply/bq25890.txt | 4 ++++
 1 file changed, 4 insertions(+)
Documentation/devicetree/bindings/power/supply/bq25890.txt +4 -0
index dc9c8f76e06c..bd214945d9dc 100644
@@ -32,6 +32,10 @@ Optional properties:
 - ti,thermal-regulation-threshold: integer, temperature above which the charge
     current is lowered, to avoid overheating (in degrees Celsius). If omitted,
     the default setting will be used (120 degrees);
+- ti,ibatcomp-resistance: integer, value of a resistor in series with
+    the battery (in uOhm);
+- ti,ibatcomp-clamp-voltage: integer, maximum charging voltage adjustment due
+    to expected voltage drop on in-series resistor (in uV);
 
 Example:
 
Signature · 1 line
2.20.1