Add Actions Semi S500 pinctrl support
Subsystems (4)
v2 cover Add Actions Semi S500 pinctrl support
This patchset adds pinctrl support for Actions Semi S500 SoC.
Pinmux functions are only accessible for pin groups while pinconf parameters are available for both pin groups and individual pins.
The pinctrl driver has been verified using RoseapplePi, the SBC for which an initial support has been provided via:
https://lore.kernel.org/lkml/[email protected]/
The DTS related changes, including the required clock support, will be available in the upcoming patch series.
Thanks,
Cristi
Changes in v2:
- Updated the pinctrl bindings according to Rob's feedback
- Set the pinctrl entry in MAINTAINERS according to Mani's suggestion
- Rebased patches on v5.8
Cristian Ciocaltea (3):
dt-bindings: pinctrl: Add bindings for Actions S500 SoC
pinctrl: actions: Add Actions S500 pinctrl driver
MAINTAINERS: Set pinctrl binding entry for all Actions Semi Owl SoCs
.../pinctrl/actions,s500-pinctrl.yaml | 240 +++ MAINTAINERS | 2 +- drivers/pinctrl/actions/Kconfig | 6 + drivers/pinctrl/actions/Makefile | 1 + drivers/pinctrl/actions/pinctrl-s500.c | 1727 +++++++++++++++++ 5 files changed, 1975 insertions(+), 1 deletion(-) create mode 100644 Documentation/devicetree/bindings/pinctrl/actions,s500-pinctrl.yaml create mode 100644 drivers/pinctrl/actions/pinctrl-s500.c
Signature · 1 line
2.28.0
PATCH v2 1/3 dt-bindings: pinctrl: Add bindings for Actions S500 SoC
Add pinctrl and gpio bindings for Actions Semi S500 SoC.
---
Changes in v2:
- Added myself to the list of maintainers, per Mani's suggestion
- Added a description item for each of the four register ranges, per Rob's feedback
- Renamed the pin nodes and got rid of the if/then hack in the patternProperties,according to Rob's suggestion
- Added a missing 'additionalProperties: false' line
- Updated the example with the new node names and the split register range
.../pinctrl/actions,s500-pinctrl.yaml | 240 ++++++++++++++++++ 1 file changed, 240 insertions(+) create mode 100644 Documentation/devicetree/bindings/pinctrl/actions,s500-pinctrl.yaml
Documentation/devicetree/bindings/pinctrl/actions,s500-pinctrl.yaml new file +240 -0
@@ -0,0 +1,240 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/actions,s500-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Actions Semi S500 SoC pinmux & GPIO controller + +maintainers: + - Manivannan Sadhasivam <[email protected]> + - Cristian Ciocaltea <[email protected]> + +description: | + Pinmux & GPIO controller manages pin multiplexing & configuration including + GPIO function selection & GPIO attributes configuration. Please refer to + pinctrl-bindings.txt in this directory for common binding part and usage. + +properties: + compatible: + const: actions,s500-pinctrl + + reg: + items: + - description: GPIO Output + GPIO Input + GPIO Data + - description: Multiplexing Control + - description: PAD Pull Control + PAD Schmitt Trigger Enable + PAD Control + - description: PAD Drive Capacity Select + minItems: 1 + maxItems: 4 + + clocks: + maxItems: 1 + + gpio-controller: true + + gpio-ranges: + maxItems: 1 + + '#gpio-cells': + description: + Specifies the pin number and flags, as defined in + include/dt-bindings/gpio/gpio.h + const: 2 + + interrupt-controller: true + + '#interrupt-cells': + description: + Specifies the pin number and flags, as defined in + include/dt-bindings/interrupt-controller/irq.h + const: 2 + + interrupts: + description: + One interrupt per each of the 5 GPIO ports supported by the controller, + sorted by port number ascending order. + minItems: 5 + maxItems: 5 + +patternProperties: + '-pins$': + type: object + patternProperties: + '^(.*-)?pinmux$': + type: object + description: + Pinctrl node's client devices specify pin muxes using subnodes, + which in turn use the standard properties below. + $ref: pinmux-node.yaml# + + properties: + groups: + description: + List of gpio pin groups affected by the functions specified in + this subnode. + items: + oneOf: + - enum: [lcd0_d18_mfp, rmii_crs_dv_mfp, rmii_txd0_mfp, + rmii_txd1_mfp, rmii_txen_mfp, rmii_rxen_mfp, rmii_rxd1_mfp, + rmii_rxd0_mfp, rmii_ref_clk_mfp, i2s_d0_mfp, i2s_pcm1_mfp, + i2s0_pcm0_mfp, i2s1_pcm0_mfp, i2s_d1_mfp, ks_in2_mfp, + ks_in1_mfp, ks_in0_mfp, ks_in3_mfp, ks_out0_mfp, + ks_out1_mfp, ks_out2_mfp, lvds_o_pn_mfp, dsi_dn0_mfp, + dsi_dp2_mfp, lcd0_d17_mfp, dsi_dp3_mfp, dsi_dn3_mfp, + dsi_dp0_mfp, lvds_ee_pn_mfp, spi0_i2c_pcm_mfp, + spi0_i2s_pcm_mfp, dsi_dnp1_cp_mfp, lvds_e_pn_mfp, + dsi_dn2_mfp, uart2_rtsb_mfp, uart2_ctsb_mfp, uart3_rtsb_mfp, + uart3_ctsb_mfp, sd0_d0_mfp, sd0_d1_mfp, sd0_d2_d3_mfp, + sd1_d0_d3_mfp, sd0_cmd_mfp, sd0_clk_mfp, sd1_cmd_mfp, + uart0_rx_mfp, clko_25m_mfp, csi_cn_cp_mfp, sens0_ckout_mfp, + uart0_tx_mfp, i2c0_mfp, csi_dn_dp_mfp, sen0_pclk_mfp, + pcm1_in_mfp, pcm1_clk_mfp, pcm1_sync_mfp, pcm1_out_mfp, + dnand_data_wr_mfp, dnand_acle_ce0_mfp, nand_ceb2_mfp, + nand_ceb3_mfp] + minItems: 1 + maxItems: 32 + + function: + description: + Specify the alternative function to be configured for the + given gpio pin groups. + enum: [nor, eth_rmii, eth_smii, spi0, spi1, spi2, spi3, sens0, + sens1, uart0, uart1, uart2, uart3, uart4, uart5, uart6, i2s0, + i2s1, pcm1, pcm0, ks, jtag, pwm0, pwm1, pwm2, pwm3, pwm4, pwm5, + p0, sd0, sd1, sd2, i2c0, i2c1, i2c3, dsi, lvds, usb30, clko_25m, + mipi_csi, nand, spdif, ts, lcd0] + + required: + - groups + - function + + additionalProperties: false + + '^(.*-)?pinconf$': + type: object + description: + Pinctrl node's client devices specify pin configurations using + subnodes, which in turn use the standard properties below. + $ref: pincfg-node.yaml# + + properties: + groups: + description: + List of gpio pin groups affected by the drive-strength property + specified in this subnode. + items: + oneOf: + - enum: [sirq_drv, rmii_txd01_txen_drv, rmii_rxer_drv, + rmii_crs_drv, rmii_rxd10_drv, rmii_ref_clk_drv, + smi_mdc_mdio_drv, i2s_d0_drv, i2s_bclk0_drv, i2s3_drv, + i2s13_drv, pcm1_drv, ks_in_drv, ks_out_drv, lvds_all_drv, + lcd_dsi_drv, dsi_drv, sd0_d0_d3_drv, sd1_d0_d3_drv, + sd0_cmd_drv, sd0_clk_drv, sd1_cmd_drv, sd1_clk_drv, + spi0_all_drv, uart0_rx_drv, uart0_tx_drv, uart2_all_drv, + i2c0_all_drv, i2c12_all_drv, sens0_pclk_drv, + sens0_ckout_drv, uart3_all_drv] + minItems: 1 + maxItems: 32 + + pins: + description: + List of gpio pins affected by the bias-pull-* and + input-schmitt-* properties specified in this subnode. + items: + oneOf: + - enum: [dnand_dqs, dnand_dqsn, eth_txd0, eth_txd1, eth_txen, + eth_rxer, eth_crs_dv, eth_rxd1, eth_rxd0, eth_ref_clk, + eth_mdc, eth_mdio, sirq0, sirq1, sirq2, i2s_d0, i2s_bclk0, + i2s_lrclk0, i2s_mclk0, i2s_d1, i2s_bclk1, i2s_lrclk1, + i2s_mclk1, ks_in0, ks_in1, ks_in2, ks_in3, ks_out0, ks_out1, + ks_out2, lvds_oep, lvds_oen, lvds_odp, lvds_odn, lvds_ocp, + lvds_ocn, lvds_obp, lvds_obn, lvds_oap, lvds_oan, lvds_eep, + lvds_een, lvds_edp, lvds_edn, lvds_ecp, lvds_ecn, lvds_ebp, + lvds_ebn, lvds_eap, lvds_ean, lcd0_d18, lcd0_d17, dsi_dp3, + dsi_dn3, dsi_dp1, dsi_dn1, dsi_cp, dsi_cn, dsi_dp0, dsi_dn0, + dsi_dp2, dsi_dn2, sd0_d0, sd0_d1, sd0_d2, sd0_d3, sd1_d0, + sd1_d1, sd1_d2, sd1_d3, sd0_cmd, sd0_clk, sd1_cmd, sd1_clk, + spi0_sclk, spi0_ss, spi0_miso, spi0_mosi, uart0_rx, + uart0_tx, i2c0_sclk, i2c0_sdata, sensor0_pclk, + sensor0_ckout, dnand_ale, dnand_cle, dnand_ceb0, dnand_ceb1, + dnand_ceb2, dnand_ceb3, uart2_rx, uart2_tx, uart2_rtsb, + uart2_ctsb, uart3_rx, uart3_tx, uart3_rtsb, uart3_ctsb, + pcm1_in, pcm1_clk, pcm1_sync, pcm1_out, i2c1_sclk, + i2c1_sdata, i2c2_sclk, i2c2_sdata, csi_dn0, csi_dp0, + csi_dn1, csi_dp1, csi_dn2, csi_dp2, csi_dn3, csi_dp3, + csi_cn, csi_cp, dnand_d0, dnand_d1, dnand_d2, dnand_d3, + dnand_d4, dnand_d5, dnand_d6, dnand_d7, dnand_rb, dnand_rdb, + dnand_rdbn, dnand_wrb, porb, clko_25m, bsel, pkg0, pkg1, + pkg2, pkg3] + minItems: 1 + maxItems: 64 + + bias-pull-up: true + bias-pull-down: true + + drive-strength: + description: + Selects the drive strength for the specified pins, in mA. + enum: [2, 4, 8, 12] + + input-schmitt-enable: true + input-schmitt-disable: true + + additionalProperties: false + + additionalProperties: false + +required: + - compatible + - reg + - clocks + - gpio-controller + - gpio-ranges + - '#gpio-cells' + - interrupt-controller + - '#interrupt-cells' + - interrupts + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + pinctrl: pinctrl@b01b0000 { + compatible = "actions,s500-pinctrl"; + reg = <0xb01b0000 0x40>, <0xb01b0040 0x10>, + <0xb01b0060 0x18>, <0xb01b0080 0xc>; + clocks = <&cmu 55>; + gpio-controller; + gpio-ranges = <&pinctrl 0 0 132>; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; + + mmc0_pins: mmc0-pins { + pinmux { + groups = "sd0_d0_mfp", "sd0_d1_mfp", "sd0_d2_d3_mfp", + "sd0_cmd_mfp", "sd0_clk_mfp"; + function = "sd0"; + }; + + drv-pinconf { + groups = "sd0_d0_d3_drv", "sd0_cmd_drv", "sd0_clk_drv"; + drive-strength = <8>; + }; + + bias-pinconf { + pins = "sd0_d0", "sd0_d1", "sd0_d2", + "sd0_d3", "sd0_cmd"; + bias-pull-up; + }; + }; + }; + +...
Signature · 1 line
2.28.0
Re: [PATCH v2 1/3] dt-bindings: pinctrl: Add bindings for Actions S500 SoC
Quoted 91 lines · Cristian Ciocaltea
Add pinctrl and gpio bindings for Actions Semi S500 SoC.
Signed-off-by Cristian Ciocaltea <[email protected]>---
Changes in v2:
- Added myself to the list of maintainers, per Mani's suggestion
- Added a description item for each of the four register ranges, per Rob's feedback
- Renamed the pin nodes and got rid of the if/then hack in the patternProperties,according to Rob's suggestion
- Added a missing 'additionalProperties: false' line
- Updated the example with the new node names and the split register range.../pinctrl/actions,s500-pinctrl.yaml | 240 ++++++++++++++++++ 1 file changed, 240 insertions(+) create mode 100644 Documentation/devicetree/bindings/pinctrl/actions,s500-pinctrl.yamlDocumentation/devicetree/bindings/pinctrl/actions,s500-pinctrl.yaml new file +67
-0@@ -0,0 +1,240 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/actions,s500-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Actions Semi S500 SoC pinmux & GPIO controller + +maintainers: + - Manivannan Sadhasivam <[email protected]> + - Cristian Ciocaltea <[email protected]> + +description: | + Pinmux & GPIO controller manages pin multiplexing & configuration including + GPIO function selection & GPIO attributes configuration. Please refer to + pinctrl-bindings.txt in this directory for common binding part and usage. + +properties: + compatible: + const: actions,s500-pinctrl + + reg: + items: + - description: GPIO Output + GPIO Input + GPIO Data + - description: Multiplexing Control + - description: PAD Pull Control + PAD Schmitt Trigger Enable + PAD Control + - description: PAD Drive Capacity Select + minItems: 1 + maxItems: 4 + + clocks: + maxItems: 1 + + gpio-controller: true + + gpio-ranges: + maxItems: 1 + + '#gpio-cells': + description: + Specifies the pin number and flags, as defined in + include/dt-bindings/gpio/gpio.h + const: 2 + + interrupt-controller: true + + '#interrupt-cells': + description: + Specifies the pin number and flags, as defined in + include/dt-bindings/interrupt-controller/irq.h + const: 2 + + interrupts: + description: + One interrupt per each of the 5 GPIO ports supported by the controller, + sorted by port number ascending order. + minItems: 5 + maxItems: 5 + +patternProperties: + '-pins$': + type: object + patternProperties: + '^(.*-)?pinmux$': + type: object + description: + Pinctrl node's client devices specify pin muxes using subnodes,
Documentation/devicetree/bindings/pinctrl/actions,s500-pinctrl.yaml line 77
Quoted 10 lines
Documentation/devicetree/bindings/pinctrl/actions,s500-pinctrl.yaml new file +10
-0+ which in turn use the standard properties below. + $ref: pinmux-node.yaml# + + properties: + groups: + description: + List of gpio pin groups affected by the functions specified in + this subnode. + items: + oneOf:
You don't need oneOf with only 1 entry.
With that and the other 2 cases fixed,
Quoted 166 lines
Documentation/devicetree/bindings/pinctrl/actions,s500-pinctrl.yaml new file +163
-0+ - enum: [lcd0_d18_mfp, rmii_crs_dv_mfp, rmii_txd0_mfp, + rmii_txd1_mfp, rmii_txen_mfp, rmii_rxen_mfp, rmii_rxd1_mfp, + rmii_rxd0_mfp, rmii_ref_clk_mfp, i2s_d0_mfp, i2s_pcm1_mfp, + i2s0_pcm0_mfp, i2s1_pcm0_mfp, i2s_d1_mfp, ks_in2_mfp, + ks_in1_mfp, ks_in0_mfp, ks_in3_mfp, ks_out0_mfp, + ks_out1_mfp, ks_out2_mfp, lvds_o_pn_mfp, dsi_dn0_mfp, + dsi_dp2_mfp, lcd0_d17_mfp, dsi_dp3_mfp, dsi_dn3_mfp, + dsi_dp0_mfp, lvds_ee_pn_mfp, spi0_i2c_pcm_mfp, + spi0_i2s_pcm_mfp, dsi_dnp1_cp_mfp, lvds_e_pn_mfp, + dsi_dn2_mfp, uart2_rtsb_mfp, uart2_ctsb_mfp, uart3_rtsb_mfp, + uart3_ctsb_mfp, sd0_d0_mfp, sd0_d1_mfp, sd0_d2_d3_mfp, + sd1_d0_d3_mfp, sd0_cmd_mfp, sd0_clk_mfp, sd1_cmd_mfp, + uart0_rx_mfp, clko_25m_mfp, csi_cn_cp_mfp, sens0_ckout_mfp, + uart0_tx_mfp, i2c0_mfp, csi_dn_dp_mfp, sen0_pclk_mfp, + pcm1_in_mfp, pcm1_clk_mfp, pcm1_sync_mfp, pcm1_out_mfp, + dnand_data_wr_mfp, dnand_acle_ce0_mfp, nand_ceb2_mfp, + nand_ceb3_mfp] + minItems: 1 + maxItems: 32 + + function: + description: + Specify the alternative function to be configured for the + given gpio pin groups. + enum: [nor, eth_rmii, eth_smii, spi0, spi1, spi2, spi3, sens0, + sens1, uart0, uart1, uart2, uart3, uart4, uart5, uart6, i2s0, + i2s1, pcm1, pcm0, ks, jtag, pwm0, pwm1, pwm2, pwm3, pwm4, pwm5, + p0, sd0, sd1, sd2, i2c0, i2c1, i2c3, dsi, lvds, usb30, clko_25m, + mipi_csi, nand, spdif, ts, lcd0] + + required: + - groups + - function + + additionalProperties: false + + '^(.*-)?pinconf$': + type: object + description: + Pinctrl node's client devices specify pin configurations using + subnodes, which in turn use the standard properties below. + $ref: pincfg-node.yaml# + + properties: + groups: + description: + List of gpio pin groups affected by the drive-strength property + specified in this subnode. + items: + oneOf: + - enum: [sirq_drv, rmii_txd01_txen_drv, rmii_rxer_drv, + rmii_crs_drv, rmii_rxd10_drv, rmii_ref_clk_drv, + smi_mdc_mdio_drv, i2s_d0_drv, i2s_bclk0_drv, i2s3_drv, + i2s13_drv, pcm1_drv, ks_in_drv, ks_out_drv, lvds_all_drv, + lcd_dsi_drv, dsi_drv, sd0_d0_d3_drv, sd1_d0_d3_drv, + sd0_cmd_drv, sd0_clk_drv, sd1_cmd_drv, sd1_clk_drv, + spi0_all_drv, uart0_rx_drv, uart0_tx_drv, uart2_all_drv, + i2c0_all_drv, i2c12_all_drv, sens0_pclk_drv, + sens0_ckout_drv, uart3_all_drv] + minItems: 1 + maxItems: 32 + + pins: + description: + List of gpio pins affected by the bias-pull-* and + input-schmitt-* properties specified in this subnode. + items: + oneOf: + - enum: [dnand_dqs, dnand_dqsn, eth_txd0, eth_txd1, eth_txen, + eth_rxer, eth_crs_dv, eth_rxd1, eth_rxd0, eth_ref_clk, + eth_mdc, eth_mdio, sirq0, sirq1, sirq2, i2s_d0, i2s_bclk0, + i2s_lrclk0, i2s_mclk0, i2s_d1, i2s_bclk1, i2s_lrclk1, + i2s_mclk1, ks_in0, ks_in1, ks_in2, ks_in3, ks_out0, ks_out1, + ks_out2, lvds_oep, lvds_oen, lvds_odp, lvds_odn, lvds_ocp, + lvds_ocn, lvds_obp, lvds_obn, lvds_oap, lvds_oan, lvds_eep, + lvds_een, lvds_edp, lvds_edn, lvds_ecp, lvds_ecn, lvds_ebp, + lvds_ebn, lvds_eap, lvds_ean, lcd0_d18, lcd0_d17, dsi_dp3, + dsi_dn3, dsi_dp1, dsi_dn1, dsi_cp, dsi_cn, dsi_dp0, dsi_dn0, + dsi_dp2, dsi_dn2, sd0_d0, sd0_d1, sd0_d2, sd0_d3, sd1_d0, + sd1_d1, sd1_d2, sd1_d3, sd0_cmd, sd0_clk, sd1_cmd, sd1_clk, + spi0_sclk, spi0_ss, spi0_miso, spi0_mosi, uart0_rx, + uart0_tx, i2c0_sclk, i2c0_sdata, sensor0_pclk, + sensor0_ckout, dnand_ale, dnand_cle, dnand_ceb0, dnand_ceb1, + dnand_ceb2, dnand_ceb3, uart2_rx, uart2_tx, uart2_rtsb, + uart2_ctsb, uart3_rx, uart3_tx, uart3_rtsb, uart3_ctsb, + pcm1_in, pcm1_clk, pcm1_sync, pcm1_out, i2c1_sclk, + i2c1_sdata, i2c2_sclk, i2c2_sdata, csi_dn0, csi_dp0, + csi_dn1, csi_dp1, csi_dn2, csi_dp2, csi_dn3, csi_dp3, + csi_cn, csi_cp, dnand_d0, dnand_d1, dnand_d2, dnand_d3, + dnand_d4, dnand_d5, dnand_d6, dnand_d7, dnand_rb, dnand_rdb, + dnand_rdbn, dnand_wrb, porb, clko_25m, bsel, pkg0, pkg1, + pkg2, pkg3] + minItems: 1 + maxItems: 64 + + bias-pull-up: true + bias-pull-down: true + + drive-strength: + description: + Selects the drive strength for the specified pins, in mA. + enum: [2, 4, 8, 12] + + input-schmitt-enable: true + input-schmitt-disable: true + + additionalProperties: false + + additionalProperties: false + +required: + - compatible + - reg + - clocks + - gpio-controller + - gpio-ranges + - '#gpio-cells' + - interrupt-controller + - '#interrupt-cells' + - interrupts + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + pinctrl: pinctrl@b01b0000 { + compatible = "actions,s500-pinctrl"; + reg = <0xb01b0000 0x40>, <0xb01b0040 0x10>, + <0xb01b0060 0x18>, <0xb01b0080 0xc>; + clocks = <&cmu 55>; + gpio-controller; + gpio-ranges = <&pinctrl 0 0 132>; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; + + mmc0_pins: mmc0-pins { + pinmux { + groups = "sd0_d0_mfp", "sd0_d1_mfp", "sd0_d2_d3_mfp", + "sd0_cmd_mfp", "sd0_clk_mfp"; + function = "sd0"; + }; + + drv-pinconf { + groups = "sd0_d0_d3_drv", "sd0_cmd_drv", "sd0_clk_drv"; + drive-strength = <8>; + }; + + bias-pinconf { + pins = "sd0_d0", "sd0_d1", "sd0_d2", + "sd0_d3", "sd0_cmd"; + bias-pull-up; + }; + }; + }; + +...Signature · 1 line
2.28.0
Re: [PATCH v2 1/3] dt-bindings: pinctrl: Add bindings for Actions S500 SoC
Quoted 105 lines · Rob Herring
Quoted 91 lines · Cristian Ciocaltea
Add pinctrl and gpio bindings for Actions Semi S500 SoC.
Signed-off-by Cristian Ciocaltea <[email protected]>---
Changes in v2:
- Added myself to the list of maintainers, per Mani's suggestion
- Added a description item for each of the four register ranges, per Rob's feedback
- Renamed the pin nodes and got rid of the if/then hack in the patternProperties,according to Rob's suggestion
- Added a missing 'additionalProperties: false' line
- Updated the example with the new node names and the split register range.../pinctrl/actions,s500-pinctrl.yaml | 240 ++++++++++++++++++ 1 file changed, 240 insertions(+) create mode 100644 Documentation/devicetree/bindings/pinctrl/actions,s500-pinctrl.yamlDocumentation/devicetree/bindings/pinctrl/actions,s500-pinctrl.yaml new file +67
-0@@ -0,0 +1,240 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/actions,s500-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Actions Semi S500 SoC pinmux & GPIO controller + +maintainers: + - Manivannan Sadhasivam <[email protected]> + - Cristian Ciocaltea <[email protected]> + +description: | + Pinmux & GPIO controller manages pin multiplexing & configuration including + GPIO function selection & GPIO attributes configuration. Please refer to + pinctrl-bindings.txt in this directory for common binding part and usage. + +properties: + compatible: + const: actions,s500-pinctrl + + reg: + items: + - description: GPIO Output + GPIO Input + GPIO Data + - description: Multiplexing Control + - description: PAD Pull Control + PAD Schmitt Trigger Enable + PAD Control + - description: PAD Drive Capacity Select + minItems: 1 + maxItems: 4 + + clocks: + maxItems: 1 + + gpio-controller: true + + gpio-ranges: + maxItems: 1 + + '#gpio-cells': + description: + Specifies the pin number and flags, as defined in + include/dt-bindings/gpio/gpio.h + const: 2 + + interrupt-controller: true + + '#interrupt-cells': + description: + Specifies the pin number and flags, as defined in + include/dt-bindings/interrupt-controller/irq.h + const: 2 + + interrupts: + description: + One interrupt per each of the 5 GPIO ports supported by the controller, + sorted by port number ascending order. + minItems: 5 + maxItems: 5 + +patternProperties: + '-pins$': + type: object + patternProperties: + '^(.*-)?pinmux$': + type: object + description: + Pinctrl node's client devices specify pin muxes using subnodes,Documentation/devicetree/bindings/pinctrl/actions,s500-pinctrl.yaml line 77
Quoted 10 lines
Documentation/devicetree/bindings/pinctrl/actions,s500-pinctrl.yaml new file +10
-0+ which in turn use the standard properties below. + $ref: pinmux-node.yaml# + + properties: + groups: + description: + List of gpio pin groups affected by the functions specified in + this subnode. + items: + oneOf:You don't need oneOf with only 1 entry.
Quoted 3 lines
With that and the other 2 cases fixed,
Reviewed-by Rob Herring <[email protected]>
Hi Rob,
Thanks for reviewing!
I tried to drop the first occurrence of the indicated 'oneOf' nodes, but I get the following error when checking the example:
actions,s500-pinctrl.example.dt.yaml: pinctrl@b01b0000: mmc0-pins:pinmux:groups:
Additional items are not allowed ('sd0_d1_mfp', 'sd0_d2_d3_mfp', 'sd0_cmd_mfp', 'sd0_clk_mfp' were unexpected)
It seems this only allows one value item to be provided:
groups = "sd0_d0_mfp";
instead of the required:
groups = "sd0_d0_mfp", "sd0_d1_mfp", "sd0_d2_d3_mfp",
"sd0_cmd_mfp", "sd0_clk_mfp";
Kind regards,
Cristi
Quoted 166 lines
Quoted 166 lines
Documentation/devicetree/bindings/pinctrl/actions,s500-pinctrl.yaml new file +163
-0+ - enum: [lcd0_d18_mfp, rmii_crs_dv_mfp, rmii_txd0_mfp, + rmii_txd1_mfp, rmii_txen_mfp, rmii_rxen_mfp, rmii_rxd1_mfp, + rmii_rxd0_mfp, rmii_ref_clk_mfp, i2s_d0_mfp, i2s_pcm1_mfp, + i2s0_pcm0_mfp, i2s1_pcm0_mfp, i2s_d1_mfp, ks_in2_mfp, + ks_in1_mfp, ks_in0_mfp, ks_in3_mfp, ks_out0_mfp, + ks_out1_mfp, ks_out2_mfp, lvds_o_pn_mfp, dsi_dn0_mfp, + dsi_dp2_mfp, lcd0_d17_mfp, dsi_dp3_mfp, dsi_dn3_mfp, + dsi_dp0_mfp, lvds_ee_pn_mfp, spi0_i2c_pcm_mfp, + spi0_i2s_pcm_mfp, dsi_dnp1_cp_mfp, lvds_e_pn_mfp, + dsi_dn2_mfp, uart2_rtsb_mfp, uart2_ctsb_mfp, uart3_rtsb_mfp, + uart3_ctsb_mfp, sd0_d0_mfp, sd0_d1_mfp, sd0_d2_d3_mfp, + sd1_d0_d3_mfp, sd0_cmd_mfp, sd0_clk_mfp, sd1_cmd_mfp, + uart0_rx_mfp, clko_25m_mfp, csi_cn_cp_mfp, sens0_ckout_mfp, + uart0_tx_mfp, i2c0_mfp, csi_dn_dp_mfp, sen0_pclk_mfp, + pcm1_in_mfp, pcm1_clk_mfp, pcm1_sync_mfp, pcm1_out_mfp, + dnand_data_wr_mfp, dnand_acle_ce0_mfp, nand_ceb2_mfp, + nand_ceb3_mfp] + minItems: 1 + maxItems: 32 + + function: + description: + Specify the alternative function to be configured for the + given gpio pin groups. + enum: [nor, eth_rmii, eth_smii, spi0, spi1, spi2, spi3, sens0, + sens1, uart0, uart1, uart2, uart3, uart4, uart5, uart6, i2s0, + i2s1, pcm1, pcm0, ks, jtag, pwm0, pwm1, pwm2, pwm3, pwm4, pwm5, + p0, sd0, sd1, sd2, i2c0, i2c1, i2c3, dsi, lvds, usb30, clko_25m, + mipi_csi, nand, spdif, ts, lcd0] + + required: + - groups + - function + + additionalProperties: false + + '^(.*-)?pinconf$': + type: object + description: + Pinctrl node's client devices specify pin configurations using + subnodes, which in turn use the standard properties below. + $ref: pincfg-node.yaml# + + properties: + groups: + description: + List of gpio pin groups affected by the drive-strength property + specified in this subnode. + items: + oneOf: + - enum: [sirq_drv, rmii_txd01_txen_drv, rmii_rxer_drv, + rmii_crs_drv, rmii_rxd10_drv, rmii_ref_clk_drv, + smi_mdc_mdio_drv, i2s_d0_drv, i2s_bclk0_drv, i2s3_drv, + i2s13_drv, pcm1_drv, ks_in_drv, ks_out_drv, lvds_all_drv, + lcd_dsi_drv, dsi_drv, sd0_d0_d3_drv, sd1_d0_d3_drv, + sd0_cmd_drv, sd0_clk_drv, sd1_cmd_drv, sd1_clk_drv, + spi0_all_drv, uart0_rx_drv, uart0_tx_drv, uart2_all_drv, + i2c0_all_drv, i2c12_all_drv, sens0_pclk_drv, + sens0_ckout_drv, uart3_all_drv] + minItems: 1 + maxItems: 32 + + pins: + description: + List of gpio pins affected by the bias-pull-* and + input-schmitt-* properties specified in this subnode. + items: + oneOf: + - enum: [dnand_dqs, dnand_dqsn, eth_txd0, eth_txd1, eth_txen, + eth_rxer, eth_crs_dv, eth_rxd1, eth_rxd0, eth_ref_clk, + eth_mdc, eth_mdio, sirq0, sirq1, sirq2, i2s_d0, i2s_bclk0, + i2s_lrclk0, i2s_mclk0, i2s_d1, i2s_bclk1, i2s_lrclk1, + i2s_mclk1, ks_in0, ks_in1, ks_in2, ks_in3, ks_out0, ks_out1, + ks_out2, lvds_oep, lvds_oen, lvds_odp, lvds_odn, lvds_ocp, + lvds_ocn, lvds_obp, lvds_obn, lvds_oap, lvds_oan, lvds_eep, + lvds_een, lvds_edp, lvds_edn, lvds_ecp, lvds_ecn, lvds_ebp, + lvds_ebn, lvds_eap, lvds_ean, lcd0_d18, lcd0_d17, dsi_dp3, + dsi_dn3, dsi_dp1, dsi_dn1, dsi_cp, dsi_cn, dsi_dp0, dsi_dn0, + dsi_dp2, dsi_dn2, sd0_d0, sd0_d1, sd0_d2, sd0_d3, sd1_d0, + sd1_d1, sd1_d2, sd1_d3, sd0_cmd, sd0_clk, sd1_cmd, sd1_clk, + spi0_sclk, spi0_ss, spi0_miso, spi0_mosi, uart0_rx, + uart0_tx, i2c0_sclk, i2c0_sdata, sensor0_pclk, + sensor0_ckout, dnand_ale, dnand_cle, dnand_ceb0, dnand_ceb1, + dnand_ceb2, dnand_ceb3, uart2_rx, uart2_tx, uart2_rtsb, + uart2_ctsb, uart3_rx, uart3_tx, uart3_rtsb, uart3_ctsb, + pcm1_in, pcm1_clk, pcm1_sync, pcm1_out, i2c1_sclk, + i2c1_sdata, i2c2_sclk, i2c2_sdata, csi_dn0, csi_dp0, + csi_dn1, csi_dp1, csi_dn2, csi_dp2, csi_dn3, csi_dp3, + csi_cn, csi_cp, dnand_d0, dnand_d1, dnand_d2, dnand_d3, + dnand_d4, dnand_d5, dnand_d6, dnand_d7, dnand_rb, dnand_rdb, + dnand_rdbn, dnand_wrb, porb, clko_25m, bsel, pkg0, pkg1, + pkg2, pkg3] + minItems: 1 + maxItems: 64 + + bias-pull-up: true + bias-pull-down: true + + drive-strength: + description: + Selects the drive strength for the specified pins, in mA. + enum: [2, 4, 8, 12] + + input-schmitt-enable: true + input-schmitt-disable: true + + additionalProperties: false + + additionalProperties: false + +required: + - compatible + - reg + - clocks + - gpio-controller + - gpio-ranges + - '#gpio-cells' + - interrupt-controller + - '#interrupt-cells' + - interrupts + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + pinctrl: pinctrl@b01b0000 { + compatible = "actions,s500-pinctrl"; + reg = <0xb01b0000 0x40>, <0xb01b0040 0x10>, + <0xb01b0060 0x18>, <0xb01b0080 0xc>; + clocks = <&cmu 55>; + gpio-controller; + gpio-ranges = <&pinctrl 0 0 132>; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; + + mmc0_pins: mmc0-pins { + pinmux { + groups = "sd0_d0_mfp", "sd0_d1_mfp", "sd0_d2_d3_mfp", + "sd0_cmd_mfp", "sd0_clk_mfp"; + function = "sd0"; + }; + + drv-pinconf { + groups = "sd0_d0_d3_drv", "sd0_cmd_drv", "sd0_clk_drv"; + drive-strength = <8>; + }; + + bias-pinconf { + pins = "sd0_d0", "sd0_d1", "sd0_d2", + "sd0_d3", "sd0_cmd"; + bias-pull-up; + }; + }; + }; + +...Signature · 1 line
2.28.0
PATCH v2 2/3 pinctrl: actions: Add Actions S500 pinctrl driver
In reply to Cristian CiocalteaAdd pinctrl and gpio driver for Actions Semi S500 SoC.
The driver supports pinctrl, pinmux, pinconf, gpio and interrupt functions using a set of registers shared between gpio and pinctrl.
---
Changes in v2:
- None
drivers/pinctrl/actions/Kconfig | 6 + drivers/pinctrl/actions/Makefile | 1 + drivers/pinctrl/actions/pinctrl-s500.c | 1727 ++++++++++++++++++++++++ 3 files changed, 1734 insertions(+) create mode 100644 drivers/pinctrl/actions/pinctrl-s500.c
drivers/pinctrl/actions/Kconfig +6 -0
@@ -10,6 +10,12 @@ config PINCTRL_OWL help Say Y here to enable Actions Semi OWL pinctrl driver +config PINCTRL_S500 + bool "Actions Semi S500 pinctrl driver" + depends on PINCTRL_OWL + help + Say Y here to enable Actions Semi S500 pinctrl driver + config PINCTRL_S700 bool "Actions Semi S700 pinctrl driver" depends on PINCTRL_OWL
drivers/pinctrl/actions/Makefile +1 -0
@@ -1,4 +1,5 @@ # SPDX-License-Identifier: GPL-2.0-only obj-$(CONFIG_PINCTRL_OWL) += pinctrl-owl.o +obj-$(CONFIG_PINCTRL_S500) += pinctrl-s500.o obj-$(CONFIG_PINCTRL_S700) += pinctrl-s700.o obj-$(CONFIG_PINCTRL_S900) += pinctrl-s900.o
drivers/pinctrl/actions/pinctrl-s500.c new file +1727 -0
1,727 lines not on this page · raw message
Signature · 1 line
2.28.0
PATCH v2 3/3 MAINTAINERS: Set pinctrl binding entry for all Actions Semi Owl SoCs
In reply to Cristian CiocalteaUpdate the pinctrl binding entry to match all members of Actions Semi Owl SoCs.
---
Changes in v2:
- Discarded the S500 specific pinctrl binding entry and instead use a generic rule to match all members of Actions Semi Owl SoCs, per Mani's suggestion
- Renamed patch to reflect the new changes, the original name was:
'Add pinctrl binding entry for Actions Semi'
MAINTAINERS | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
MAINTAINERS +1 -1
@@ -1519,7 +1519,7 @@ F: Documentation/devicetree/bindings/clock/actions,owl-cmu.txt F: Documentation/devicetree/bindings/dma/owl-dma.txt F: Documentation/devicetree/bindings/i2c/i2c-owl.txt F: Documentation/devicetree/bindings/mmc/owl-mmc.yaml -F: Documentation/devicetree/bindings/pinctrl/actions,s900-pinctrl.txt +F: Documentation/devicetree/bindings/pinctrl/actions,* F: Documentation/devicetree/bindings/power/actions,owl-sps.txt F: Documentation/devicetree/bindings/timer/actions,owl-timer.txt F: arch/arm/boot/dts/owl-*
Signature · 1 line
2.28.0
Quoted 8 lines · Cristian Ciocaltea
This patchset adds pinctrl support for Actions Semi S500 SoC.
Pinmux functions are only accessible for pin groups while pinconf parameters are available for both pin groups and individual pins.
The pinctrl driver has been verified using RoseapplePi, the SBC for which an initial support has been provided via:
https://lore.kernel.org/lkml/[email protected]/
No comments on the v2 patch set for more than 2 weeks so patches applied. If people find issues we can make incremental patches.
Thanks!
Linus Walleij
Quoted 12 lines · Linus Walleij
Quoted 8 lines · Cristian Ciocaltea
This patchset adds pinctrl support for Actions Semi S500 SoC.
Pinmux functions are only accessible for pin groups while pinconf parameters are available for both pin groups and individual pins.
The pinctrl driver has been verified using RoseapplePi, the SBC for which an initial support has been provided via:
https://lore.kernel.org/lkml/[email protected]/
Quoted 6 lines
No comments on the v2 patch set for more than 2 weeks so patches applied. If people find issues we can make incremental patches.
Thanks!
Linus Walleij
Thanks,
Cristi