sms911x: DTS fixes and DT binding to json-schema conversion

Hi all,

This patch series converts the Smart Mixed-Signal Connectivity (SMSC) LAN911x/912x Controller Device Tree binding documentation to json-schema, after fixing a few issues in DTS files.

Changed compared to v1[1]:
- Dropped applied patches,
- Add Reviewed-by,
- Drop bogus double quotes in compatible values,
- Add comment explaining why "additionalProperties: true" is needed.

Thanks!

[1] [PATCH 0/5] sms911x: DTS fixes and DT binding to json-schema conversion

    https://lore.kernel.org/r/[email protected]

Geert Uytterhoeven (2):
ARM: dts: qcom-apq8060: Correct Ethernet node name and drop bogus irq
property
dt-bindings: net: sms911x: Convert to json-schema

 .../devicetree/bindings/net/gpmc-eth.txt      |   2 +-
 .../devicetree/bindings/net/smsc,lan9115.yaml | 110 ++++++++++++++++++
 .../devicetree/bindings/net/smsc911x.txt      |  43 -------
 .../arm/boot/dts/qcom-apq8060-dragonboard.dts |   4 +-
 4 files changed, 112 insertions(+), 47 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/net/smsc,lan9115.yaml
 delete mode 100644 Documentation/devicetree/bindings/net/smsc911x.txt

2.25.1

Gr{oetje,eeting}s,

						Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- [email protected]

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
							    -- Linus Torvalds

make dtbs_check:

ethernet-ebi2@2,0: $nodename:0: 'ethernet-ebi2@2,0' does not match '^ethernet(@.*)?$' ethernet-ebi2@2,0: 'smsc,irq-active-low' does not match any of the regexes: 'pinctrl-[0-9]+'

There is no "smsc,irq-active-low" property, as active low is the default.

---
v2:
- Add Reviewed-by.

---
 arch/arm/boot/dts/qcom-apq8060-dragonboard.dts | 4 +---
 1 file changed, 1 insertion(+), 3 deletions(-)

index dace8ffeb99118cb..0a4ffd10c48464f5 100644
@@ -581,7 +581,7 @@ external-bus@1a100000 {
 			 * EBI2. This has a 25MHz chrystal next to it, so no
 			 * clocking is needed.
 			 */
-			ethernet-ebi2@2,0 {
+			ethernet@2,0 {
 				compatible = "smsc,lan9221", "smsc,lan9115";
 				reg = <2 0x0 0x100>;
 				/*

@@ -598,8 +598,6 @@ ethernet-ebi2@2,0 {
 				phy-mode = "mii";
 				reg-io-width = <2>;
 				smsc,force-external-phy;
-				/* IRQ on edge falling = active low */
-				smsc,irq-active-low;
 				smsc,irq-push-pull;
 
 				/*

2.25.1

Convert the Smart Mixed-Signal Connectivity (SMSC) LAN911x/912x Controller Device Tree binding documentation to json-schema.

Document missing properties.
Make "phy-mode" not required, as many DTS files do not have it, and the Linux drivers falls back to PHY_INTERFACE_MODE_NA.
Correct nodename in example.

---
I have listed Shawn as the maintainer, as he wrote the original bindings. Shawn: Please scream if this is inappropriate ;-)

v2:
- Drop bogus double quotes in compatible values,
- Add comment explaining why "additionalProperties: true" is needed.

---
 .../devicetree/bindings/net/gpmc-eth.txt      |   2 +-
 .../devicetree/bindings/net/smsc,lan9115.yaml | 110 ++++++++++++++++++
 .../devicetree/bindings/net/smsc911x.txt      |  43 -------
 3 files changed, 111 insertions(+), 44 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/net/smsc,lan9115.yaml
 delete mode 100644 Documentation/devicetree/bindings/net/smsc911x.txt

index f7da3d73ca1b2e15..32821066a85b0078 100644
@@ -13,7 +13,7 @@ Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt
 
 For the properties relevant to the ethernet controller connected to the GPMC
 refer to the binding documentation of the device. For example, the documentation
-for the SMSC 911x is Documentation/devicetree/bindings/net/smsc911x.txt
+for the SMSC 911x is Documentation/devicetree/bindings/net/smsc,lan9115.yaml
 
 Child nodes need to specify the GPMC bus address width using the "bank-width"
 property but is possible that an ethernet controller also has a property to

2.25.1