mtd: spi-nor: Add support for Infineon s25hl-t/s25hs-t
Subsystems (5)
v15 cover mtd: spi-nor: Add support for Infineon s25hl-t/s25hs-t
From: Takahiro Kuwano <[email protected]>
The S25HL-T/S25HS-T family is the Infineon SEMPER Flash with Quad SPI.
The datasheets can be found in the following link.
https://www.infineon.com/dgdl/Infineon-S25HS256T_S25HS512T_S25HS01GT_S25HL256T_S25HL512T_S25HL01GT_256-Mb_(32-MB)_512-Mb_(64-MB)_1-Gb_(128-MB)_HS-T_(1.8-V)_HL-T_(3.0-V)_Semper_Flash_with_Quad_SPI-DataSheet-v02_00-EN.pdf?fileId=8ac78c8c7d0d8da4017d0ee674b86ee3&da=t
Device ID, SFDP, and test script output:
------------------------------------------------------------
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/partname s25hl512t
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id 342a1a0f0390
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer spansion
zynq> xxd -p /sys/bus/spi/devices/spi0.0/spi-nor/sfdp 53464450080103ff00000114000100ff84000102500100ff81000116c801 00ff8700011c580100ffffffffffffffffffffffffffffffffffffffffff ffffffffffffffffffffffffffffffffffffffffffffffffffffffffffff ffffffffffffffffffffffffffffffffffffffffffffffffffffffffffff ffffffffffffffffffffffffffffffffffffffffffffffffffffffffffff ffffffffffffffffffffffffffffffffffffffffffffffffffffffffffff ffffffffffffffffffffffffffffffffffffffffffffffffffffffffffff ffffffffffffffffffffffffffffffffffffffffffffffffffffffffffff ffffffffffffffffffffffffffffffffe720faffffffff1f48eb086b00ff 88bbfeffffffffff00ffffff48eb0c2000ff00ff12d823faff8b82e7ffe3 ec031c608a857a75f766805c8cd6ddfff938f8a1000000000000bc000000 0000f7f5ffff7b920ffe21ffffdc0000800000000000c0ffc3ebc8ffe3eb 00650090060500a10065009600650095716503d0716503d000000000b02e 000088a489aa716503967165039600000000000000000000000000000000 000000000000000000000000000000000000000000000000716505d57165 05d50000a015fc65ff0804008000fc65ff4002008000fd65ff0402008000 fe0002fff1ff0100f8ff0100f8fffb03fe0302fff8fffb03f8ff0100f1ff 0100fe0104fff1ff0000f8ff0200f8fff703f8ff0200f1ff0000ff0400ff f8ffff03
zynq> md5sum /sys/bus/spi/devices/spi0.0/spi-nor/sfdp 8a0aa90112e154ae3a797df2c211ef61 /sys/bus/spi/devices/spi0.0/spi-nor/sfdp zynq> test_qspi.sh
6+0 records in
6+0 records out
6291456 bytes (6.0MB) copied, 0.221878 seconds, 27.0MB/s Copied 6291456 bytes from qspi_test to address 0x00000000 in flash Erased 6291456 bytes from address 0x00000000 in flash
Copied 6291456 bytes from address 0x00000000 in flash to qspi_read 0000000 ffff ffff ffff ffff ffff ffff ffff ffff
*
0600000
Copied 6291456 bytes from qspi_test to address 0x00000000 in flash Copied 6291456 bytes from address 0x00000000 in flash to qspi_read 9ef41f0cece253ea6b6537ab19e0878841954444 qspi_test 9ef41f0cece253ea6b6537ab19e0878841954444 qspi_read
------------------------------------------------------------
------------------------------------------------------------
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/partname s25hs01gt
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id 342b1b0f0390
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer spansion
zynq> xxd -p /sys/bus/spi/devices/spi0.0/spi-nor/sfdp 53464450080103ff00000114000100ff84000102500100ff81000116c801 00ff8700011c580100ffffffffffffffffffffffffffffffffffffffffff ffffffffffffffffffffffffffffffffffffffffffffffffffffffffffff ffffffffffffffffffffffffffffffffffffffffffffffffffffffffffff ffffffffffffffffffffffffffffffffffffffffffffffffffffffffffff ffffffffffffffffffffffffffffffffffffffffffffffffffffffffffff ffffffffffffffffffffffffffffffffffffffffffffffffffffffffffff ffffffffffffffffffffffffffffffffffffffffffffffffffffffffffff ffffffffffffffffffffffffffffffffe720faffffffff3f48eb086b00ff 88bbfeffffffffff00ffffff48eb0c2000ff00ff12d823faff8b82e7ffe6 ec031c608a857a75f766805c8cd6ddfff938f8a1000000000000bc000000 0000f7f5ffff7b920ffe21ffffdc0000800000000000c0ffc3ebc8ffe3eb 00650090060500a10065009600650095716503d0716503d000000000b02e 000088a489aa716503967165039600000000000000000000000000000000 000000000000000000000000000000000000000000000000716505d57165 05d50000a015fc65ff0804008000fc65ff4002008000fd65ff0402008000 fe0002fff1ff0100f8ff0100f8fffb07fe0302fff8fffb07f8ff0100f1ff 0100fe0104fff1ff0000f8ff0200f8fff707f8ff0200f1ff0000ff0400ff f8ffff07
zynq> md5sum /sys/bus/spi/devices/spi0.0/spi-nor/sfdp 1ad5a0d7d7e0e656986c1e678c416a7e /sys/bus/spi/devices/spi0.0/spi-nor/sfdp zynq> test_qspi.sh
6+0 records in
6+0 records out
6291456 bytes (6.0MB) copied, 0.221968 seconds, 27.0MB/s Copied 6291456 bytes from qspi_test to address 0x00000000 in flash Erased 6291456 bytes from address 0x00000000 in flash
Copied 6291456 bytes from address 0x00000000 in flash to qspi_read 0000000 ffff ffff ffff ffff ffff ffff ffff ffff
*
0600000
Copied 6291456 bytes from qspi_test to address 0x00000000 in flash Copied 6291456 bytes from address 0x00000000 in flash to qspi_read 43cf65d1b77dc4bdc31ca002166f150a97843cb2 qspi_test 43cf65d1b77dc4bdc31ca002166f150a97843cb2 qspi_read
------------------------------------------------------------
------------------------------------------------------------
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/partname s25hl01gt
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id 342a1b0f0390
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer spansion
zynq> xxd -p /sys/bus/spi/devices/spi0.0/spi-nor/sfdp 53464450080103ff00000114000100ff84000102500100ff81000116c801 00ff8700011c580100ffffffffffffffffffffffffffffffffffffffffff ffffffffffffffffffffffffffffffffffffffffffffffffffffffffffff ffffffffffffffffffffffffffffffffffffffffffffffffffffffffffff ffffffffffffffffffffffffffffffffffffffffffffffffffffffffffff ffffffffffffffffffffffffffffffffffffffffffffffffffffffffffff ffffffffffffffffffffffffffffffffffffffffffffffffffffffffffff ffffffffffffffffffffffffffffffffffffffffffffffffffffffffffff ffffffffffffffffffffffffffffffffe720faffffffff3f48eb086b00ff 88bbfeffffffffff00ffffff48eb0c2000ff00ff12d823faff8b82e7ffe6 ec031c608a857a75f766805c8cd6ddfff938f8a1000000000000bc000000 0000f7f5ffff7b920ffe21ffffdc0000800000000000c0ffc3ebc8ffe3eb 00650090060500a10065009600650095716503d0716503d000000000b02e 000088a489aa716503967165039600000000000000000000000000000000 000000000000000000000000000000000000000000000000716505d57165 05d50000a015fc65ff0804008000fc65ff4002008000fd65ff0402008000 fe0002fff1ff0100f8ff0100f8fffb07fe0302fff8fffb07f8ff0100f1ff 0100fe0104fff1ff0000f8ff0200f8fff707f8ff0200f1ff0000ff0400ff f8ffff07
zynq> md5sum /sys/bus/spi/devices/spi0.0/spi-nor/sfdp 1ad5a0d7d7e0e656986c1e678c416a7e /sys/bus/spi/devices/spi0.0/spi-nor/sfdp zynq> test_qspi.sh
6+0 records in
6+0 records out
6291456 bytes (6.0MB) copied, 0.221797 seconds, 27.1MB/s Copied 6291456 bytes from qspi_test to address 0x00000000 in flash Erased 6291456 bytes from address 0x00000000 in flash
Copied 6291456 bytes from address 0x00000000 in flash to qspi_read 0000000 ffff ffff ffff ffff ffff ffff ffff ffff
*
0600000
Copied 6291456 bytes from qspi_test to address 0x00000000 in flash Copied 6291456 bytes from address 0x00000000 in flash to qspi_read e4d22bbd91abe16d43dc4a0539ac49d653e99611 qspi_test e4d22bbd91abe16d43dc4a0539ac49d653e99611 qspi_read
------------------------------------------------------------
------------------------------------------------------------
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/partname s25hs01gt
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id 342b1b0f0390
zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer spansion
zynq> xxd -p /sys/bus/spi/devices/spi0.0/spi-nor/sfdp 53464450080103ff00000114000100ff84000102500100ff81000116c801 00ff8700011c580100ffffffffffffffffffffffffffffffffffffffffff ffffffffffffffffffffffffffffffffffffffffffffffffffffffffffff ffffffffffffffffffffffffffffffffffffffffffffffffffffffffffff ffffffffffffffffffffffffffffffffffffffffffffffffffffffffffff ffffffffffffffffffffffffffffffffffffffffffffffffffffffffffff ffffffffffffffffffffffffffffffffffffffffffffffffffffffffffff ffffffffffffffffffffffffffffffffffffffffffffffffffffffffffff ffffffffffffffffffffffffffffffffe720faffffffff3f48eb086b00ff 88bbfeffffffffff00ffffff48eb0c2000ff00ff12d823faff8b82e7ffe6 ec031c608a857a75f766805c8cd6ddfff938f8a1000000000000bc000000 0000f7f5ffff7b920ffe21ffffdc0000800000000000c0ffc3ebc8ffe3eb 00650090060500a10065009600650095716503d0716503d000000000b02e 000088a489aa716503967165039600000000000000000000000000000000 000000000000000000000000000000000000000000000000716505d57165 05d50000a015fc65ff0804008000fc65ff4002008000fd65ff0402008000 fe0002fff1ff0100f8ff0100f8fffb07fe0302fff8fffb07f8ff0100f1ff 0100fe0104fff1ff0000f8ff0200f8fff707f8ff0200f1ff0000ff0400ff f8ffff07
zynq> md5sum /sys/bus/spi/devices/spi0.0/spi-nor/sfdp 1ad5a0d7d7e0e656986c1e678c416a7e /sys/bus/spi/devices/spi0.0/spi-nor/sfdp zynq> test_qspi.sh
6+0 records in
6+0 records out
6291456 bytes (6.0MB) copied, 0.221968 seconds, 27.0MB/s Copied 6291456 bytes from qspi_test to address 0x00000000 in flash Erased 6291456 bytes from address 0x00000000 in flash
Copied 6291456 bytes from address 0x00000000 in flash to qspi_read 0000000 ffff ffff ffff ffff ffff ffff ffff ffff
*
0600000
Copied 6291456 bytes from qspi_test to address 0x00000000 in flash Copied 6291456 bytes from address 0x00000000 in flash to qspi_read 43cf65d1b77dc4bdc31ca002166f150a97843cb2 qspi_test 43cf65d1b77dc4bdc31ca002166f150a97843cb2 qspi_read
------------------------------------------------------------
---
Changes in v15:
- add missing read any reg call in volatile quad enable method (patch 8/8)
Changes in v14:
- add prerequisite patches for s25hl-t/s25hs-t addition.
- squash volatile quad enable method to the patch that adds the flashes to avoid unused function warning.
Changes in v13:
- Remove patch, Call set_4byte_addr_mode() before spi_nor_quad_enalbe()
- Remove patch, Rename local macro
- Use 3-byte address width in cypress_nor_quad_enable_volatile()
- Add post_sfdp to fix 3 byte erase opcode in 4BAIT
Changes in v12:
- Rebase on top of Tudor's series
https://patchwork.ozlabs.org/project/linux-mtd/list/?series=295933 https://patchwork.ozlabs.org/project/linux-mtd/list/?series=294533
- New patch: Retain nor->addr_width at 4BAIT parse
- New patch: Call set_4byte_addr_mode() before spi_nor_quad_enalbe()
- New patch: Rename local macro
Changes in v11:
- Rebase on top of Tudor's series
https://patchwork.ozlabs.org/project/linux-mtd/list/?series=294490
- Remove 'nor->info->addr_width for SMPT parse' patch
Changes in v10:
- Rebase to v5.18-rc1
- Remove dependencies on other series
- Use nor->info->addr_width for SMPT parse
- Add a local function for page size discovery
- Clean up volatile QE function
Changes in v9:
- Rebase to v5.17-rc6
- Rename function and macro per mwalle's series
- Fix some issues in ID table and fixup hook
Changes in v8:
- Rebase to v5.17-rc4
- Use spi_nor_read_reg and spi_nor_write_reg()
Changes in v7:
- Some changes were missing in v6 patch. Fix it
Changes in v6:
- Remove 2Gb dual die package parts and related changes to split mulit die package support into another series of patches
Changes in v5:
- Fix 'if (ret == 1)' to 'if (ret < 0)' in spansion_read_any_reg()
- Add NO_CHIP_ERASE flag to S25HL02GT and S25HS02GT
Changes in v4:
- Reword 'legacy' to 'default'
- Rename spi_nor_read() to spi_nor_default_ready()
- Fix dummy cycle calculation in spansion_read_any_reg()
- Modify comment for spansion_write_any_reg()
- Merge block comments about SMPT in s25hx_t_post_sfdp_fixups()
- Remove USE_CLSR flags from S25HL02GT and S25HS02GT
Changes in v3:
- Split into multiple patches
- Remove S25HL256T and S25HS256T
- Add S25HL02GT and S25HS02GT
- Add support for multi-die package parts support
- Cleanup Read/Write Any Register implementation
- Remove erase_map fix for top/split sector layout
- Set ECC data unit size (16B) to writesize
Changes in v2:
- Remove SPI_NOR_SKIP_SFDP flag and clean up related fixups
- Check CFR3V[4] to determine page_size instead of force 512B
- Depend on the patchset below to support non-uniform sector layout
https://lore.kernel.org/linux-mtd/[email protected]/*** BLURB HERE ***
Takahiro Kuwano (3):
mtd: spi-nor: Retain nor->addr_width at 4BAIT parse
mtd: spi-nor: spansion: Add local function to discover page size
mtd: spi-nor: spansion: Add s25hl-t/s25hs-t IDs and fixups
Tudor Ambarus (5):
mtd: spi-nor: s/addr_width/addr_nbytes
mtd: spi-nor: core: Shrink the storage size of the flash_info's
addr_nbytes
mtd: spi-nor: sfdp: Clarify that nor->read_{opcode, dummy} are
uninitialized
mtd: spi-nor: Do not change nor->addr_nbytes at SFDP parsing time
mtd: spi-nor: core: Couple the number of address bytes with the
address mode
drivers/mtd/spi-nor/controllers/aspeed-smc.c | 6 +- drivers/mtd/spi-nor/controllers/hisi-sfc.c | 2 +- drivers/mtd/spi-nor/controllers/nxp-spifi.c | 8 +- drivers/mtd/spi-nor/core.c | 155 ++++++++-------- drivers/mtd/spi-nor/core.h | 14 +- drivers/mtd/spi-nor/issi.c | 2 +- drivers/mtd/spi-nor/otp.c | 12 +- drivers/mtd/spi-nor/sfdp.c | 43 ++--- drivers/mtd/spi-nor/spansion.c | 183 ++++++++++++++++--- drivers/mtd/spi-nor/xilinx.c | 2 +- include/linux/mtd/spi-nor.h | 4 +- 11 files changed, 285 insertions(+), 146 deletions(-)
Signature · 6 lines
2.25.1 ______________________________________________________ Linux MTD discussion mailing list http://lists.infradead.org/mailman/listinfo/linux-mtd/
PATCH v15 1/8 mtd: spi-nor: s/addr_width/addr_nbytes
From: Tudor Ambarus <[email protected]>
Address width was an unfortunate name, as it means the number of IO lines used for the address, whereas in the code it is used as the number of address bytes. s/addr_width/addr_nbytes throughout the entire SPI NOR framework.
--- drivers/mtd/spi-nor/controllers/aspeed-smc.c | 6 +-- drivers/mtd/spi-nor/controllers/hisi-sfc.c | 2 +- drivers/mtd/spi-nor/controllers/nxp-spifi.c | 8 ++-- drivers/mtd/spi-nor/core.c | 46 ++++++++++---------- drivers/mtd/spi-nor/core.h | 12 ++--- drivers/mtd/spi-nor/issi.c | 2 +- drivers/mtd/spi-nor/otp.c | 12 ++--- drivers/mtd/spi-nor/sfdp.c | 32 +++++++------- drivers/mtd/spi-nor/xilinx.c | 2 +- include/linux/mtd/spi-nor.h | 4 +- 10 files changed, 63 insertions(+), 63 deletions(-)
drivers/mtd/spi-nor/controllers/aspeed-smc.c +3 -3
@@ -350,10 +350,10 @@ static void aspeed_smc_send_cmd_addr(struct spi_nor *nor, u8 cmd, u32 addr)__be32 temp;u32 cmdaddr; -switch (nor->addr_width) { +switch (nor->addr_nbytes) {default :WARN_ONCE (1 ,"Unexpected address width %u, defaulting to 3\n" , - nor->addr_width); + nor->addr_nbytes); fallthrough;case 3 : cmdaddr = addr &0xFFFFFF ;
@@ -709,7 +709,7 @@ static int aspeed_smc_chip_setup_finish(struct aspeed_smc_chip *chip)const struct aspeed_smc_info *info = controller->info;u32 cmd; -if (chip->nor.addr_width ==4 && info->set_4b) +if (chip->nor.addr_nbytes ==4 && info->set_4b) info->set_4b (chip);/* This is for direct AHB access when using Command Mode. */
drivers/mtd/spi-nor/controllers/hisi-sfc.c +1 -1
@@ -237,7 +237,7 @@ static int hisi_spi_nor_dma_transfer(struct spi_nor *nor, loff_t start_off, reg =readl (host->regbase +FMC_CFG ); reg &= ~(FMC_CFG_OP_MODE_MASK |SPI_NOR_ADDR_MODE_MASK ); reg |=FMC_CFG_OP_MODE_NORMAL ; - reg |= (nor->addr_width ==4 ) ?SPI_NOR_ADDR_MODE_4BYTES + reg |= (nor->addr_nbytes ==4 ) ?SPI_NOR_ADDR_MODE_4BYTES :SPI_NOR_ADDR_MODE_3BYTES ;writel (reg, host->regbase +FMC_CFG );
drivers/mtd/spi-nor/controllers/nxp-spifi.c +4 -4
@@ -203,7 +203,7 @@ static ssize_t nxp_spifi_write(struct spi_nor *nor, loff_t to, size_t len,SPIFI_CMD_DATALEN (len) |SPIFI_CMD_FIELDFORM_ALL_SERIAL |SPIFI_CMD_OPCODE (nor->program_opcode) | -SPIFI_CMD_FRAMEFORM (spifi->nor.addr_width +1 ); +SPIFI_CMD_FRAMEFORM (spifi->nor.addr_nbytes +1 );writel (cmd, spifi->io_base +SPIFI_CMD );for (i =0 ; i < len; i++)
@@ -230,7 +230,7 @@ static int nxp_spifi_erase(struct spi_nor *nor, loff_t offs) cmd =SPIFI_CMD_FIELDFORM_ALL_SERIAL |SPIFI_CMD_OPCODE (nor->erase_opcode) | -SPIFI_CMD_FRAMEFORM (spifi->nor.addr_width +1 ); +SPIFI_CMD_FRAMEFORM (spifi->nor.addr_nbytes +1 );writel (cmd, spifi->io_base +SPIFI_CMD );return nxp_spifi_wait_for_cmd (spifi);
@@ -252,12 +252,12 @@ static int nxp_spifi_setup_memory_cmd(struct nxp_spifi *spifi) }/* Memory mode supports address length between 1 and 4 */ -if (spifi->nor.addr_width <1 || spifi->nor.addr_width >4 ) +if (spifi->nor.addr_nbytes <1 || spifi->nor.addr_nbytes >4 )return -EINVAL ; spifi->mcmd |=SPIFI_CMD_OPCODE (spifi->nor.read_opcode) |SPIFI_CMD_INTLEN (spifi->nor.read_dummy /8 ) | -SPIFI_CMD_FRAMEFORM (spifi->nor.addr_width +1 ); +SPIFI_CMD_FRAMEFORM (spifi->nor.addr_nbytes +1 );return 0 ; }
drivers/mtd/spi-nor/core.c +23 -23
141 lines not on this page · raw message
drivers/mtd/spi-nor/core.h +6 -6
@@ -90,9 +90,9 @@ SPI_MEM_OP_NO_DUMMY, \ SPI_MEM_OP_NO_DATA) -#define SPI_NOR_SECTOR_ERASE_OP (opcode, addr_width, addr) \ +#define SPI_NOR_SECTOR_ERASE_OP (opcode, addr_nbytes, addr) \ SPI_MEM_OP(SPI_MEM_OP_CMD(opcode, 0), \ - SPI_MEM_OP_ADDR(addr_width, addr, 0), \ + SPI_MEM_OP_ADDR(addr_nbytes, addr, 0), \ SPI_MEM_OP_NO_DUMMY, \ SPI_MEM_OP_NO_DATA)
@@ -434,7 +434,7 @@ struct spi_nor_fixups {* isn't necessarily called a "sector" by the vendor. * @n_sectors: the number of sectors. * @page_size: the flash's page size. -* @addr_width: the flash's address width. +* @addr_nbytes: number of address bytes to send. * * @parse_sfdp: true when flash supports SFDP tables. The false value has no * meaning. If one wants to skip the SFDP tables, one should
@@ -493,7 +493,7 @@ struct flash_info {unsigned sector_size;u16 n_sectors;u16 page_size; -u16 addr_width; +u16 addr_nbytes;bool parse_sfdp;u16 flags;
@@ -555,11 +555,11 @@ struct flash_info { .n_sectors = (_n_sectors), \ .page_size = 256, \ -#define CAT25_INFO (_sector_size, _n_sectors, _page_size, _addr_width) \ +#define CAT25_INFO (_sector_size, _n_sectors, _page_size, _addr_nbytes) \ .sector_size = (_sector_size), \ .n_sectors = (_n_sectors), \ .page_size = (_page_size), \ - .addr_width = (_addr_width), \ + .addr_nbytes = (_addr_nbytes), \ .flags = SPI_NOR_NO_ERASE | SPI_NOR_NO_FR, \#define OTP_INFO (_len, _n_regions, _base, _offset) \
drivers/mtd/spi-nor/issi.c +1 -1
@@ -20,7 +20,7 @@ is25lp256_post_bfpt_fixups(struct spi_nor *nor,*/ if ((bfpt->dwords[BFPT_DWORD (1 )] &BFPT_DWORD1_ADDRESS_BYTES_MASK ) ==BFPT_DWORD1_ADDRESS_BYTES_3_ONLY ) - nor->addr_width =4 ; + nor->addr_nbytes =4 ;return 0 ; }
drivers/mtd/spi-nor/otp.c +6 -6
@@ -35,13 +35,13 @@*/ int spi_nor_otp_read_secr (struct spi_nor *nor,loff_t addr,size_t len,u8 *buf) { -u8 addr_width, read_opcode, read_dummy; +u8 addr_nbytes, read_opcode, read_dummy;struct spi_mem_dirmap_desc *rdesc;enum spi_nor_protocol read_proto;int ret; read_opcode = nor->read_opcode; - addr_width = nor->addr_width; + addr_nbytes = nor->addr_nbytes; read_dummy = nor->read_dummy; read_proto = nor->read_proto; rdesc = nor->dirmap.rdesc;
@@ -54,7 +54,7 @@ int spi_nor_otp_read_secr(struct spi_nor *nor, loff_t addr, size_t len, u8 *buf) ret =spi_nor_read_data (nor, addr, len, buf); nor->read_opcode = read_opcode; - nor->addr_width = addr_width; + nor->addr_nbytes = addr_nbytes; nor->read_dummy = read_dummy; nor->read_proto = read_proto; nor->dirmap.rdesc = rdesc;
@@ -85,11 +85,11 @@ int spi_nor_otp_write_secr(struct spi_nor *nor, loff_t addr, size_t len, {enum spi_nor_protocol write_proto;struct spi_mem_dirmap_desc *wdesc; -u8 addr_width, program_opcode; +u8 addr_nbytes, program_opcode;int ret, written; program_opcode = nor->program_opcode; - addr_width = nor->addr_width; + addr_nbytes = nor->addr_nbytes; write_proto = nor->write_proto; wdesc = nor->dirmap.wdesc;
@@ -113,7 +113,7 @@ int spi_nor_otp_write_secr(struct spi_nor *nor, loff_t addr, size_t len, out: nor->program_opcode = program_opcode; - nor->addr_width = addr_width; + nor->addr_nbytes = addr_nbytes; nor->write_proto = write_proto; nor->dirmap.wdesc = wdesc;
drivers/mtd/spi-nor/sfdp.c +16 -16
@@ -134,7 +134,7 @@ struct sfdp_4bait {/** * spi_nor_read_raw() - raw read of serial flash memory. read_opcode, -* addr_width and read_dummy members of the struct spi_nor +* addr_nbytes and read_dummy members of the struct spi_nor * should be previously * set. * @nor: pointer to a 'struct spi_nor'
@@ -178,21 +178,21 @@ static int spi_nor_read_raw(struct spi_nor *nor, u32 addr, size_t len, u8 *buf)static int spi_nor_read_sfdp (struct spi_nor *nor,u32 addr,size_t len,void *buf) { -u8 addr_width, read_opcode, read_dummy; +u8 addr_nbytes, read_opcode, read_dummy;int ret; read_opcode = nor->read_opcode; - addr_width = nor->addr_width; + addr_nbytes = nor->addr_nbytes; read_dummy = nor->read_dummy; nor->read_opcode =SPINOR_OP_RDSFDP ; - nor->addr_width =3 ; + nor->addr_nbytes =3 ; nor->read_dummy =8 ; ret =spi_nor_read_raw (nor, addr, len, buf); nor->read_opcode = read_opcode; - nor->addr_width = addr_width; + nor->addr_nbytes = addr_nbytes; nor->read_dummy = read_dummy;return ret;
@@ -462,11 +462,11 @@ static int spi_nor_parse_bfpt(struct spi_nor *nor,switch (bfpt.dwords[BFPT_DWORD (1 )] &BFPT_DWORD1_ADDRESS_BYTES_MASK ) {case BFPT_DWORD1_ADDRESS_BYTES_3_ONLY :case BFPT_DWORD1_ADDRESS_BYTES_3_OR_4 : - nor->addr_width =3 ; + nor->addr_nbytes =3 ;break ;case BFPT_DWORD1_ADDRESS_BYTES_4_ONLY : - nor->addr_width =4 ; + nor->addr_nbytes =4 ;break ;default :
@@ -637,12 +637,12 @@ static int spi_nor_parse_bfpt(struct spi_nor *nor, }/** -* spi_nor_smpt_addr_width() - return the address width used in the +* spi_nor_smpt_addr_nbytes() - return the number of address bytes used in the * configuration detection command. * @nor: pointer to a 'struct spi_nor' * @settings: configuration detection command descriptor, dword1 */ -static u8 spi_nor_smpt_addr_width (const struct spi_nor *nor,const u32 settings) +static u8 spi_nor_smpt_addr_nbytes (const struct spi_nor *nor,const u32 settings) {switch (settings &SMPT_CMD_ADDRESS_LEN_MASK ) {case SMPT_CMD_ADDRESS_LEN_0 :
@@ -653,7 +653,7 @@ static u8 spi_nor_smpt_addr_width(const struct spi_nor *nor, const u32 settings)return 4 ;case SMPT_CMD_ADDRESS_LEN_USE_CURRENT :default : -return nor->addr_width; +return nor->addr_nbytes; } }
@@ -690,7 +690,7 @@ static const u32 *spi_nor_get_map_in_use(struct spi_nor *nor, const u32 *smpt,u32 addr;int err;u8 i; -u8 addr_width, read_opcode, read_dummy; +u8 addr_nbytes, read_opcode, read_dummy;u8 read_data_mask, map_id;/* Use a kmalloc'ed bounce buffer to guarantee it is DMA-able. */
@@ -698,7 +698,7 @@ static const u32 *spi_nor_get_map_in_use(struct spi_nor *nor, const u32 *smpt,if (!buf)return ERR_PTR (-ENOMEM ); - addr_width = nor->addr_width; + addr_nbytes = nor->addr_nbytes; read_dummy = nor->read_dummy; read_opcode = nor->read_opcode;
@@ -709,7 +709,7 @@ static const u32 *spi_nor_get_map_in_use(struct spi_nor *nor, const u32 *smpt,break ; read_data_mask =SMPT_CMD_READ_DATA (smpt[i]); - nor->addr_width =spi_nor_smpt_addr_width (nor, smpt[i]); + nor->addr_nbytes =spi_nor_smpt_addr_nbytes (nor, smpt[i]); nor->read_dummy =spi_nor_smpt_read_dummy (nor, smpt[i]); nor->read_opcode =SMPT_CMD_OPCODE (smpt[i]); addr = smpt[i +1 ];
@@ -756,7 +756,7 @@ static const u32 *spi_nor_get_map_in_use(struct spi_nor *nor, const u32 *smpt,/* fall through */ out:kfree (buf); - nor->addr_width = addr_width; + nor->addr_nbytes = addr_nbytes; nor->read_dummy = read_dummy; nor->read_opcode = read_opcode;return ret;
@@ -1044,7 +1044,7 @@ static int spi_nor_parse_4bait(struct spi_nor *nor,/* * We need at least one 4-byte op code per read, program and erase * operation; the .read(), .write() and .erase() hooks share the -* nor->addr_width value. +* nor->addr_nbytes value. */ if (!read_hwcaps || !pp_hwcaps || !erase_mask) goto out;
@@ -1098,7 +1098,7 @@ static int spi_nor_parse_4bait(struct spi_nor *nor,* Spansion memory. However this quirk is no longer needed with new * SFDP compliant memories. */ - nor->addr_width =4 ; + nor->addr_nbytes =4 ; nor->flags |=SNOR_F_4B_OPCODES |SNOR_F_HAS_4BAIT ;/* fall through */
drivers/mtd/spi-nor/xilinx.c +1 -1
@@ -31,7 +31,7 @@ .sector_size = (8 * (_page_size)), \ .n_sectors = (_n_sectors), \ .page_size = (_page_size), \ - .addr_width =3 , \ + .addr_nbytes =3 , \ .flags = SPI_NOR_NO_FR/* Xilinx S3AN share MFR with Atmel SPI NOR */
include/linux/mtd/spi-nor.h +2 -2
@@ -353,7 +353,7 @@ struct spi_nor_flash_parameter;* @bouncebuf_size: size of the bounce buffer * @info: SPI NOR part JEDEC MFR ID and other info * @manufacturer: SPI NOR manufacturer -* @addr_width: number of address bytes +* @addr_nbytes: number of address bytes * @erase_opcode: the opcode for erasing a sector * @read_opcode: the read opcode * @read_dummy: the dummy needed by the read operation
@@ -382,7 +382,7 @@ struct spi_nor {size_t bouncebuf_size;const struct flash_info *info;const struct spi_nor_manufacturer *manufacturer; -u8 addr_width; +u8 addr_nbytes;u8 erase_opcode;u8 read_opcode;u8 read_dummy;
Signature · 6 lines
2.25.1 ______________________________________________________ Linux MTD discussion mailing list http://lists.infradead.org/mailman/listinfo/linux-mtd/
Re: [PATCH v15 1/8] mtd: spi-nor: s/addr_width/addr_nbytes
Am 2022-05-10 00:10, schrieb [email protected]:
Quoted 8 lines
From: Tudor Ambarus <[email protected]>
Address width was an unfortunate name, as it means the number of IO lines used for the address, whereas in the code it is used as the number of address bytes. s/addr_width/addr_nbytes throughout the entire SPI NOR framework.
Signed-off-by Tudor Ambarus <[email protected]>
I'm not a big fan of just renaming, but
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
Re: [PATCH v15 1/8] mtd: spi-nor: s/addr_width/addr_nbytes
In reply to [email protected]Quoted 26 lines · On 10/05/22 07:10AM, [email protected] wrote:
From: Tudor Ambarus <[email protected]>
Address width was an unfortunate name, as it means the number of IO lines used for the address, whereas in the code it is used as the number of address bytes. s/addr_width/addr_nbytes throughout the entire SPI NOR framework.
Signed-off-by Tudor Ambarus <[email protected]>--- drivers/mtd/spi-nor/controllers/aspeed-smc.c | 6 +-- drivers/mtd/spi-nor/controllers/hisi-sfc.c | 2 +- drivers/mtd/spi-nor/controllers/nxp-spifi.c | 8 ++-- drivers/mtd/spi-nor/core.c | 46 ++++++++++---------- drivers/mtd/spi-nor/core.h | 12 ++--- drivers/mtd/spi-nor/issi.c | 2 +- drivers/mtd/spi-nor/otp.c | 12 ++--- drivers/mtd/spi-nor/sfdp.c | 32 +++++++------- drivers/mtd/spi-nor/xilinx.c | 2 +- include/linux/mtd/spi-nor.h | 4 +- 10 files changed, 63 insertions(+), 63 deletions(-)drivers/mtd/spi-nor/controllers/aspeed-smc.c +0
-0
drivers/mtd/spi-nor/controllers/aspeed-smc.c static void aspeed_smc_send_cmd_addr(struct spi_nor *nor, u8 cmd, u32 addr) · line 355
Quoted 7 lines
drivers/mtd/spi-nor/controllers/aspeed-smc.c +1
-1@@ -350,10 +350,10 @@ static void aspeed_smc_send_cmd_addr(struct spi_nor *nor, u8 cmd, u32 addr)__be32 temp;u32 cmdaddr; -switch (nor->addr_width) { +switch (nor->addr_nbytes) {default : WARN_ONCE(1, "Unexpected address width %u, defaulting to 3\n",
s/width/nbytes/ here as well.
Quoted 78 lines
drivers/mtd/spi-nor/controllers/aspeed-smc.c +2
-2- nor->addr_width); + nor->addr_nbytes); fallthrough;case 3 : cmdaddr = addr &0xFFFFFF ;@@ -709,7 +709,7 @@ static int aspeed_smc_chip_setup_finish(struct aspeed_smc_chip *chip)const struct aspeed_smc_info *info = controller->info;u32 cmd; -if (chip->nor.addr_width ==4 && info->set_4b) +if (chip->nor.addr_nbytes ==4 && info->set_4b) info->set_4b (chip);/* This is for direct AHB access when using Command Mode. */ drivers/mtd/spi-nor/controllers/hisi-sfc.c +1
-1@@ -237,7 +237,7 @@ static int hisi_spi_nor_dma_transfer(struct spi_nor *nor, loff_t start_off, reg =readl (host->regbase +FMC_CFG ); reg &= ~(FMC_CFG_OP_MODE_MASK |SPI_NOR_ADDR_MODE_MASK ); reg |=FMC_CFG_OP_MODE_NORMAL ; - reg |= (nor->addr_width ==4 ) ?SPI_NOR_ADDR_MODE_4BYTES + reg |= (nor->addr_nbytes ==4 ) ?SPI_NOR_ADDR_MODE_4BYTES :SPI_NOR_ADDR_MODE_3BYTES ;writel (reg, host->regbase +FMC_CFG );drivers/mtd/spi-nor/controllers/nxp-spifi.c +4
-4@@ -203,7 +203,7 @@ static ssize_t nxp_spifi_write(struct spi_nor *nor, loff_t to, size_t len,SPIFI_CMD_DATALEN (len) |SPIFI_CMD_FIELDFORM_ALL_SERIAL |SPIFI_CMD_OPCODE (nor->program_opcode) | -SPIFI_CMD_FRAMEFORM (spifi->nor.addr_width +1 ); +SPIFI_CMD_FRAMEFORM (spifi->nor.addr_nbytes +1 );writel (cmd, spifi->io_base +SPIFI_CMD );for (i =0 ; i < len; i++)@@ -230,7 +230,7 @@ static int nxp_spifi_erase(struct spi_nor *nor, loff_t offs) cmd =SPIFI_CMD_FIELDFORM_ALL_SERIAL |SPIFI_CMD_OPCODE (nor->erase_opcode) | -SPIFI_CMD_FRAMEFORM (spifi->nor.addr_width +1 ); +SPIFI_CMD_FRAMEFORM (spifi->nor.addr_nbytes +1 );writel (cmd, spifi->io_base +SPIFI_CMD );return nxp_spifi_wait_for_cmd (spifi);@@ -252,12 +252,12 @@ static int nxp_spifi_setup_memory_cmd(struct nxp_spifi *spifi) }/* Memory mode supports address length between 1 and 4 */ -if (spifi->nor.addr_width <1 || spifi->nor.addr_width >4 ) +if (spifi->nor.addr_nbytes <1 || spifi->nor.addr_nbytes >4 )return -EINVAL ; spifi->mcmd |=SPIFI_CMD_OPCODE (spifi->nor.read_opcode) |SPIFI_CMD_INTLEN (spifi->nor.read_dummy /8 ) | -SPIFI_CMD_FRAMEFORM (spifi->nor.addr_width +1 ); +SPIFI_CMD_FRAMEFORM (spifi->nor.addr_nbytes +1 );return 0 ; }drivers/mtd/spi-nor/core.c +1
-1@@ -38,7 +38,7 @@*/ #define CHIP_ERASE_2MB_READY_WAIT_JIFFIES (40UL * HZ) -#define SPI_NOR_MAX_ADDR_WIDTH 4 +#define SPI_NOR_MAX_ADDR_NBYTES 4#define SPI_NOR_SRST_SLEEP_MIN 200#define SPI_NOR_SRST_SLEEP_MAX 400
drivers/mtd/spi-nor/core.c static ssize_t spi_nor_spimem_read_data(struct spi_nor *nor, loff_t from, · line 201
Quoted 5 lines
drivers/mtd/spi-nor/core.c +1
-1@@ -198,7 +198,7 @@ static ssize_t spi_nor_spimem_read_data(struct spi_nor *nor, loff_t from, {struct spi_mem_op op = SPI_MEM_OP(SPI_MEM_OP_CMD(nor->read_opcode, 0), - SPI_MEM_OP_ADDR(nor->addr_width, from, 0), + SPI_MEM_OP_ADDR(nor->addr_nbytes, from, 0),
I am guessing this patch no longer applies since c0abb861c5d0 ("mtd:
spi-nor: Introduce templates for SPI NOR operations"). Patch looks good otherwise.
[...]
Signature · 7 lines
Regards, Pratyush Yadav Texas Instruments Inc. ______________________________________________________ Linux MTD discussion mailing list http://lists.infradead.org/mailman/listinfo/linux-mtd/
PATCH v15 2/8 mtd: spi-nor: core: Shrink the storage size of the flash_info's addr_nbytes
In reply to [email protected]From: Tudor Ambarus <[email protected]>
The maximum number of address bytes in SPI NOR is 4. Shrink the storage size of the flash_info's addr_nbytes.
--- drivers/mtd/spi-nor/core.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/mtd/spi-nor/core.h +1 -1
@@ -493,7 +493,7 @@ struct flash_info {unsigned sector_size;u16 n_sectors;u16 page_size; -u16 addr_nbytes; +u8 addr_nbytes;bool parse_sfdp;u16 flags;
Signature · 6 lines
2.25.1 ______________________________________________________ Linux MTD discussion mailing list http://lists.infradead.org/mailman/listinfo/linux-mtd/
Re: [PATCH v15 2/8] mtd: spi-nor: core: Shrink the storage size of the flash_info's addr_nbytes
Am 2022-05-10 00:10, schrieb [email protected]:
Quoted 6 lines
From: Tudor Ambarus <[email protected]>
The maximum number of address bytes in SPI NOR is 4. Shrink the storage size of the flash_info's
addr_nbytes.Signed-off-by Tudor Ambarus <[email protected]>
I'm not even sure if this actually shrink the size due to alignments of the members by the compiler, nor do I see any value in saving one byte. But anyway:
-michael
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
Re: [PATCH v15 2/8] mtd: spi-nor: core: Shrink the storage size of the flash_info's addr_nbytes
In reply to [email protected]Quoted 6 lines · On 10/05/22 07:10AM, [email protected] wrote:
From: Tudor Ambarus <[email protected]>
The maximum number of address bytes in SPI NOR is 4. Shrink the storage size of the flash_info's
addr_nbytes.Signed-off-by Tudor Ambarus <[email protected]>
Signature · 7 lines
Regards, Pratyush Yadav Texas Instruments Inc. ______________________________________________________ Linux MTD discussion mailing list http://lists.infradead.org/mailman/listinfo/linux-mtd/
PATCH v15 3/8 mtd: spi-nor: sfdp: Clarify that nor->read_{opcode, dummy} are uninitialized
In reply to [email protected]From: Tudor Ambarus <[email protected]>
nor->read_{opcode, dummy} are uninitialized (value zero) at SFDP parsing time. Clarify that in the code.
--- drivers/mtd/spi-nor/sfdp.c | 18 ++++++++---------- 1 file changed, 8 insertions(+), 10 deletions(-)
drivers/mtd/spi-nor/sfdp.c +8 -10
@@ -178,12 +178,10 @@ static int spi_nor_read_raw(struct spi_nor *nor, u32 addr, size_t len, u8 *buf)static int spi_nor_read_sfdp (struct spi_nor *nor,u32 addr,size_t len,void *buf) { -u8 addr_nbytes, read_opcode, read_dummy; +u8 addr_nbytes;int ret; - read_opcode = nor->read_opcode; addr_nbytes = nor->addr_nbytes; - read_dummy = nor->read_dummy; nor->read_opcode =SPINOR_OP_RDSFDP ; nor->addr_nbytes =3 ;
@@ -191,9 +189,10 @@ static int spi_nor_read_sfdp(struct spi_nor *nor, u32 addr, ret =spi_nor_read_raw (nor, addr, len, buf); - nor->read_opcode = read_opcode; nor->addr_nbytes = addr_nbytes; - nor->read_dummy = read_dummy; +/* Restore setup to its uninitialized state. */ + nor->read_opcode =0 ; + nor->read_dummy =0 ;return ret; }
@@ -690,7 +689,7 @@ static const u32 *spi_nor_get_map_in_use(struct spi_nor *nor, const u32 *smpt,u32 addr;int err;u8 i; -u8 addr_nbytes, read_opcode, read_dummy; +u8 addr_nbytes;u8 read_data_mask, map_id;/* Use a kmalloc'ed bounce buffer to guarantee it is DMA-able. */
@@ -699,8 +698,6 @@ static const u32 *spi_nor_get_map_in_use(struct spi_nor *nor, const u32 *smpt,return ERR_PTR (-ENOMEM ); addr_nbytes = nor->addr_nbytes; - read_dummy = nor->read_dummy; - read_opcode = nor->read_opcode; map_id =0 ;/* Determine if there are any optional Detection Command Descriptors */
@@ -757,8 +754,9 @@ static const u32 *spi_nor_get_map_in_use(struct spi_nor *nor, const u32 *smpt, out:kfree (buf); nor->addr_nbytes = addr_nbytes; - nor->read_dummy = read_dummy; - nor->read_opcode = read_opcode; +/* Restore setup to its uninitialized state. */ + nor->read_dummy =0 ; + nor->read_opcode =0 ;return ret; }
Signature · 6 lines
2.25.1 ______________________________________________________ Linux MTD discussion mailing list http://lists.infradead.org/mailman/listinfo/linux-mtd/
Re: [PATCH v15 3/8] mtd: spi-nor: sfdp: Clarify that nor->read_{opcode, dummy} are uninitialized
Am 2022-05-10 00:10, schrieb [email protected]:
Quoted 66 lines
From: Tudor Ambarus <[email protected]>
nor->read_{opcode, dummy} are uninitialized (value zero) at SFDP parsing time. Clarify that in the code.
Signed-off-by Tudor Ambarus <[email protected]>Tested-by Takahiro Kuwano <[email protected]>--- drivers/mtd/spi-nor/sfdp.c | 18 ++++++++---------- 1 file changed, 8 insertions(+), 10 deletions(-)drivers/mtd/spi-nor/sfdp.c +1
-3@@ -178,12 +178,10 @@ static int spi_nor_read_raw(struct spi_nor *nor, u32 addr, size_t len, u8 *buf) static int spi_nor_read_sfdp(struct spi_nor *nor, u32 addr, size_t len, void *buf) { - u8 addr_nbytes, read_opcode, read_dummy; + u8 addr_nbytes;int ret; - read_opcode = nor->read_opcode; addr_nbytes = nor->addr_nbytes; - read_dummy = nor->read_dummy; nor->read_opcode =SPINOR_OP_RDSFDP ;drivers/mtd/spi-nor/sfdp.c +3
-2nor->addr_nbytes =3 ;@@ -191,9 +189,10 @@ static int spi_nor_read_sfdp(struct spi_nor *nor,u32 addr, ret =spi_nor_read_raw (nor, addr, len, buf); - nor->read_opcode = read_opcode; nor->addr_nbytes = addr_nbytes; - nor->read_dummy = read_dummy; +/* Restore setup to its uninitialized state. */ + nor->read_opcode =0 ; + nor->read_dummy =0 ;return ret;}
drivers/mtd/spi-nor/sfdp.c +1
-1@@ -690,7 +689,7 @@ static const u32 *spi_nor_get_map_in_use(struct spi_nor *nor, const u32 *smpt, u32 addr;int err;u8 i; -u8 addr_nbytes, read_opcode, read_dummy; +u8 addr_nbytes;u8 read_data_mask, map_id;drivers/mtd/spi-nor/sfdp.c +0
-2/* Use a kmalloc'ed bounce buffer to guarantee it is DMA-able. */ @@ -699,8 +698,6 @@ static const u32 *spi_nor_get_map_in_use(struct spi_nor *nor, const u32 *smpt, return ERR_PTR(-ENOMEM); addr_nbytes = nor->addr_nbytes; - read_dummy = nor->read_dummy; - read_opcode = nor->read_opcode; map_id =0 ;/* Determine if there are any optional Detection Command Descriptors
*/
drivers/mtd/spi-nor/sfdp.c static const u32 *spi_nor_get_map_in_use(struct · line 758
Quoted 7 lines
drivers/mtd/spi-nor/sfdp.c +1
-2@@ -757,8 +754,9 @@ static const u32 *spi_nor_get_map_in_use(struct spi_nor *nor, const u32 *smpt, out:kfree (buf ); nor->addr_nbytes = addr_nbytes; - nor->read_dummy = read_dummy; - nor->read_opcode = read_opcode; +/* Restore setup to its uninitialized state. */
Who is modifying this? FWIW, I don't like this because it's now different than all the other occurrences of this pattern. Ultimately, I'd like to get rid of all these
saved_params = params;
params = new_params;spi_nor_call()
params = saved_params;
And instead use something like
__spi_nor_call(non_default_params);
-michael
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
Michael Walle
Reviewed-byRe: [PATCH v15 3/8] mtd: spi-nor: sfdp: Clarify that nor->read_{opcode, dummy} are uninitialized
Am 2022-05-12 23:33, schrieb Michael Walle:
Quoted 63 lines
Am 2022-05-10 00:10, schrieb [email protected]:
Quoted 62 lines
From: Tudor Ambarus <[email protected]>
nor->read_{opcode, dummy} are uninitialized (value zero) at SFDP parsing time. Clarify that in the code.
Signed-off-by Tudor Ambarus <[email protected]>Tested-by Takahiro Kuwano <[email protected]>--- drivers/mtd/spi-nor/sfdp.c | 18 ++++++++---------- 1 file changed, 8 insertions(+), 10 deletions(-)drivers/mtd/spi-nor/sfdp.c +1
-3@@ -178,12 +178,10 @@ static int spi_nor_read_raw(struct spi_nor *nor, u32 addr, size_t len, u8 *buf) static int spi_nor_read_sfdp(struct spi_nor *nor, u32 addr, size_t len, void *buf) { - u8 addr_nbytes, read_opcode, read_dummy; + u8 addr_nbytes;int ret; - read_opcode = nor->read_opcode; addr_nbytes = nor->addr_nbytes; - read_dummy = nor->read_dummy; nor->read_opcode =SPINOR_OP_RDSFDP ;drivers/mtd/spi-nor/sfdp.c +3
-2nor->addr_nbytes =3 ;@@ -191,9 +189,10 @@ static int spi_nor_read_sfdp(struct spi_nor *nor,u32 addr, ret =spi_nor_read_raw (nor, addr, len, buf); - nor->read_opcode = read_opcode; nor->addr_nbytes = addr_nbytes; - nor->read_dummy = read_dummy; +/* Restore setup to its uninitialized state. */ + nor->read_opcode =0 ; + nor->read_dummy =0 ;return ret;}
drivers/mtd/spi-nor/sfdp.c +1
-1@@ -690,7 +689,7 @@ static const u32 *spi_nor_get_map_in_use(struct spi_nor *nor, const u32 *smpt, u32 addr;int err;u8 i; -u8 addr_nbytes, read_opcode, read_dummy; +u8 addr_nbytes;u8 read_data_mask, map_id;drivers/mtd/spi-nor/sfdp.c +0
-2/* Use a kmalloc'ed bounce buffer to guarantee it is DMA-able. */ @@ -699,8 +698,6 @@ static const u32 *spi_nor_get_map_in_use(struct spi_nor *nor, const u32 *smpt, return ERR_PTR(-ENOMEM); addr_nbytes = nor->addr_nbytes; - read_dummy = nor->read_dummy; - read_opcode = nor->read_opcode;
Quoted 13 lines
drivers/mtd/spi-nor/sfdp.c static const u32 *spi_nor_get_map_in_use(struct · line 758
Quoted 11 lines
drivers/mtd/spi-nor/sfdp.c +0
-0map_id =0 ;/* Determine if there are any optional Detection Command Descriptors
*/drivers/mtd/spi-nor/sfdp.c +1
-2@@ -757,8 +754,9 @@ static const u32 *spi_nor_get_map_in_use(struct spi_nor *nor, const u32 *smpt, out:kfree (buf ); nor->addr_nbytes = addr_nbytes; - nor->read_dummy = read_dummy; - nor->read_opcode = read_opcode; +/* Restore setup to its uninitialized state. */ Who is modifying this?
Ahh scrap that, this very function. I need to go to sleep.
I just saw your next patch which will also get rid of the addr_nbytes. I'd still like to get rid of this state sometime and pass it as an additional parameter. But:
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
Re: [PATCH v15 3/8] mtd: spi-nor: sfdp: Clarify that nor->read_{opcode, dummy} are uninitialized
In reply to [email protected]Quoted 30 lines · On 10/05/22 07:10AM, [email protected] wrote:
From: Tudor Ambarus <[email protected]>
nor->read_{opcode, dummy} are uninitialized (value zero) at SFDP parsing time. Clarify that in the code.
Signed-off-by Tudor Ambarus <[email protected]>Tested-by Takahiro Kuwano <[email protected]>--- drivers/mtd/spi-nor/sfdp.c | 18 ++++++++---------- 1 file changed, 8 insertions(+), 10 deletions(-)drivers/mtd/spi-nor/sfdp.c +1
-3@@ -178,12 +178,10 @@ static int spi_nor_read_raw(struct spi_nor *nor, u32 addr, size_t len, u8 *buf)static int spi_nor_read_sfdp (struct spi_nor *nor,u32 addr,size_t len,void *buf) { -u8 addr_nbytes, read_opcode, read_dummy; +u8 addr_nbytes;int ret; - read_opcode = nor->read_opcode; addr_nbytes = nor->addr_nbytes; - read_dummy = nor->read_dummy; nor->read_opcode =SPINOR_OP_RDSFDP ; nor->addr_nbytes =3 ;
drivers/mtd/spi-nor/sfdp.c static int spi_nor_read_sfdp(struct spi_nor *nor, u32 addr, · line 195
Quoted 9 lines
drivers/mtd/spi-nor/sfdp.c +3
-2@@ -191,9 +189,10 @@ static int spi_nor_read_sfdp(struct spi_nor *nor, u32 addr, ret =spi_nor_read_raw (nor, addr, len, buf); - nor->read_opcode = read_opcode; nor->addr_nbytes = addr_nbytes; - nor->read_dummy = read_dummy; +/* Restore setup to its uninitialized state. */ + nor->read_opcode =0 ; + nor->read_dummy =0 ;
Hmm, I don't like this too much. Why do you need to explicitly set the default value here? What's wrong with this function just not caring about what is initialized by this point and what is not? It is really not its business caring about default values of these parameters. Modify them, run the command, and restore them, regardless of default or initialized values.
Quoted 36 lines
drivers/mtd/spi-nor/sfdp.c +4
-5return ret; }@@ -690,7 +689,7 @@ static const u32 *spi_nor_get_map_in_use(struct spi_nor *nor, const u32 *smpt,u32 addr;int err;u8 i; -u8 addr_nbytes, read_opcode, read_dummy; +u8 addr_nbytes;u8 read_data_mask, map_id;/* Use a kmalloc'ed bounce buffer to guarantee it is DMA-able. */ @@ -699,8 +698,6 @@ static const u32 *spi_nor_get_map_in_use(struct spi_nor *nor, const u32 *smpt,return ERR_PTR (-ENOMEM ); addr_nbytes = nor->addr_nbytes; - read_dummy = nor->read_dummy; - read_opcode = nor->read_opcode; map_id =0 ;/* Determine if there are any optional Detection Command Descriptors */ @@ -757,8 +754,9 @@ static const u32 *spi_nor_get_map_in_use(struct spi_nor *nor, const u32 *smpt, out:kfree (buf); nor->addr_nbytes = addr_nbytes; - nor->read_dummy = read_dummy; - nor->read_opcode = read_opcode; +/* Restore setup to its uninitialized state. */ + nor->read_dummy =0 ; + nor->read_opcode =0 ;return ret; }Signature · 1 line
2.25.1
Signature · 7 lines
Regards, Pratyush Yadav Texas Instruments Inc. ______________________________________________________ Linux MTD discussion mailing list http://lists.infradead.org/mailman/listinfo/linux-mtd/
PATCH v15 4/8 mtd: spi-nor: Do not change nor->addr_nbytes at SFDP parsing time
In reply to [email protected]From: Tudor Ambarus <[email protected]>
At the SFDP parsing time we should not change members of struct spi_nor, but instead fill members of struct spi_nor_flash_parameters which could leter on be used by callers. The caller will then decide if SFDP params should be used and more importantly when they should be used. Clean the code flow and don't initialize nor->addr_nbytes at SFDP parsing time.
--- drivers/mtd/spi-nor/core.c | 5 ++--- drivers/mtd/spi-nor/core.h | 2 ++ drivers/mtd/spi-nor/sfdp.c | 18 ++++++------------ 3 files changed, 10 insertions(+), 15 deletions(-)
drivers/mtd/spi-nor/core.c +2 -3
@@ -2272,8 +2272,8 @@ static int spi_nor_default_setup(struct spi_nor *nor,static int spi_nor_set_addr_nbytes (struct spi_nor *nor) { -if (nor->addr_nbytes) { -/* already configured from SFDP */ +if (nor->params->addr_nbytes) { + nor->addr_nbytes = nor->params->addr_nbytes; }else if (nor->read_proto ==SNOR_PROTO_8_8_8_DTR ) {/* * In 8D-8D-8D mode, one byte takes half a cycle to transfer. So
@@ -2518,7 +2518,6 @@ static void spi_nor_sfdp_init_params_deprecated(struct spi_nor *nor)if (spi_nor_parse_sfdp (nor)) {memcpy (nor->params, &sfdp_params,sizeof (*nor->params)); - nor->addr_nbytes =0 ; nor->flags &= ~SNOR_F_4B_OPCODES ; } }
drivers/mtd/spi-nor/core.h +2 -0
@@ -345,6 +345,7 @@ struct spi_nor_otp {* @writesize Minimal writable flash unit size. Defaults to 1. Set to * ECC unit size for ECC-ed flashes. * @page_size: the page size of the SPI NOR flash memory. +* @addr_nbytes: number of address bytes to send. * @rdsr_dummy: dummy cycles needed for Read Status Register command * in octal DTR mode. * @rdsr_addr_nbytes: dummy address bytes needed for Read Status Register
@@ -377,6 +378,7 @@ struct spi_nor_flash_parameter {u64 size;u32 writesize;u32 page_size; +u8 addr_nbytes;u8 rdsr_dummy;u8 rdsr_addr_nbytes;
drivers/mtd/spi-nor/sfdp.c +6 -12
@@ -178,19 +178,16 @@ static int spi_nor_read_raw(struct spi_nor *nor, u32 addr, size_t len, u8 *buf)static int spi_nor_read_sfdp (struct spi_nor *nor,u32 addr,size_t len,void *buf) { -u8 addr_nbytes;int ret; - addr_nbytes = nor->addr_nbytes; - nor->read_opcode =SPINOR_OP_RDSFDP ; nor->addr_nbytes =3 ; nor->read_dummy =8 ; ret =spi_nor_read_raw (nor, addr, len, buf); - nor->addr_nbytes = addr_nbytes;/* Restore setup to its uninitialized state. */ + nor->addr_nbytes =0 ; nor->read_opcode =0 ; nor->read_dummy =0 ;
@@ -461,11 +458,11 @@ static int spi_nor_parse_bfpt(struct spi_nor *nor,switch (bfpt.dwords[BFPT_DWORD (1 )] &BFPT_DWORD1_ADDRESS_BYTES_MASK ) {case BFPT_DWORD1_ADDRESS_BYTES_3_ONLY :case BFPT_DWORD1_ADDRESS_BYTES_3_OR_4 : - nor->addr_nbytes =3 ; + params->addr_nbytes =3 ;break ;case BFPT_DWORD1_ADDRESS_BYTES_4_ONLY : - nor->addr_nbytes =4 ; + params->addr_nbytes =4 ;break ;default :
@@ -652,7 +649,7 @@ static u8 spi_nor_smpt_addr_nbytes(const struct spi_nor *nor, const u32 settingsreturn 4 ;case SMPT_CMD_ADDRESS_LEN_USE_CURRENT :default : -return nor->addr_nbytes; +return nor->params->addr_nbytes; } }
@@ -689,7 +686,6 @@ static const u32 *spi_nor_get_map_in_use(struct spi_nor *nor, const u32 *smpt,u32 addr;int err;u8 i; -u8 addr_nbytes;u8 read_data_mask, map_id;/* Use a kmalloc'ed bounce buffer to guarantee it is DMA-able. */
@@ -697,8 +693,6 @@ static const u32 *spi_nor_get_map_in_use(struct spi_nor *nor, const u32 *smpt,if (!buf)return ERR_PTR (-ENOMEM ); - addr_nbytes = nor->addr_nbytes; - map_id =0 ;/* Determine if there are any optional Detection Command Descriptors */ for (i =0 ; i < smpt_len; i +=2 ) {
@@ -753,8 +747,8 @@ static const u32 *spi_nor_get_map_in_use(struct spi_nor *nor, const u32 *smpt,/* fall through */ out:kfree (buf); - nor->addr_nbytes = addr_nbytes;/* Restore setup to its uninitialized state. */ + nor->addr_nbytes =0 ; nor->read_dummy =0 ; nor->read_opcode =0 ;return ret;
@@ -1096,7 +1090,7 @@ static int spi_nor_parse_4bait(struct spi_nor *nor,* Spansion memory. However this quirk is no longer needed with new * SFDP compliant memories. */ - nor->addr_nbytes =4 ; + params->addr_nbytes =4 ; nor->flags |=SNOR_F_4B_OPCODES |SNOR_F_HAS_4BAIT ;/* fall through */
Signature · 6 lines
2.25.1 ______________________________________________________ Linux MTD discussion mailing list http://lists.infradead.org/mailman/listinfo/linux-mtd/
Re: [PATCH v15 4/8] mtd: spi-nor: Do not change nor->addr_nbytes at SFDP parsing time
Am 2022-05-10 00:10, schrieb [email protected]:
Quoted 10 lines
From: Tudor Ambarus <[email protected]>
At the SFDP parsing time we should not change members of struct
spi_nor, but instead fill members of structspi_nor_flash_parameterswhich could leter on be used by callers. The caller will then decide if SFDP params should be used and more importantly when they should be used. Clean the code flow and don't initializenor->addr_nbytesat SFDP parsing time.Signed-off-by Tudor Ambarus <[email protected]>Tested-by Takahiro Kuwano <[email protected]>
Nice!
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
Re: [PATCH v15 4/8] mtd: spi-nor: Do not change nor->addr_nbytes at SFDP parsing time
In reply to [email protected]Quoted 5 lines · On 10/05/22 07:10AM, [email protected] wrote:
From: Tudor Ambarus <[email protected]>
At the SFDP parsing time we should not change members of struct
spi_nor, but instead fill members of structspi_nor_flash_parameterswhich could leter on be used by callers. The caller will then decide if SFDP params
s/leter/later/
Quoted 120 lines
should be used and more importantly when they should be used. Clean the code flow and don't initialize
nor->addr_nbytesat SFDP parsing time.Signed-off-by Tudor Ambarus <[email protected]>Tested-by Takahiro Kuwano <[email protected]>--- drivers/mtd/spi-nor/core.c | 5 ++--- drivers/mtd/spi-nor/core.h | 2 ++ drivers/mtd/spi-nor/sfdp.c | 18 ++++++------------ 3 files changed, 10 insertions(+), 15 deletions(-)drivers/mtd/spi-nor/core.c +2
-3@@ -2272,8 +2272,8 @@ static int spi_nor_default_setup(struct spi_nor *nor,static int spi_nor_set_addr_nbytes (struct spi_nor *nor) { -if (nor->addr_nbytes) { -/* already configured from SFDP */ +if (nor->params->addr_nbytes) { + nor->addr_nbytes = nor->params->addr_nbytes; }else if (nor->read_proto ==SNOR_PROTO_8_8_8_DTR ) {/* * In 8D-8D-8D mode, one byte takes half a cycle to transfer. So @@ -2518,7 +2518,6 @@ static void spi_nor_sfdp_init_params_deprecated(struct spi_nor *nor)if (spi_nor_parse_sfdp (nor)) {memcpy (nor->params, &sfdp_params,sizeof (*nor->params)); - nor->addr_nbytes =0 ; nor->flags &= ~SNOR_F_4B_OPCODES ; } }drivers/mtd/spi-nor/core.h +2
-0@@ -345,6 +345,7 @@ struct spi_nor_otp {* @writesize Minimal writable flash unit size. Defaults to 1. Set to * ECC unit size for ECC-ed flashes. * @page_size: the page size of the SPI NOR flash memory. +* @addr_nbytes: number of address bytes to send. * @rdsr_dummy: dummy cycles needed for Read Status Register command * in octal DTR mode. * @rdsr_addr_nbytes: dummy address bytes needed for Read Status Register @@ -377,6 +378,7 @@ struct spi_nor_flash_parameter {u64 size;u32 writesize;u32 page_size; +u8 addr_nbytes;u8 rdsr_dummy;u8 rdsr_addr_nbytes;drivers/mtd/spi-nor/sfdp.c +4
-10@@ -178,19 +178,16 @@ static int spi_nor_read_raw(struct spi_nor *nor, u32 addr, size_t len, u8 *buf)static int spi_nor_read_sfdp (struct spi_nor *nor,u32 addr,size_t len,void *buf) { -u8 addr_nbytes;int ret; - addr_nbytes = nor->addr_nbytes; - nor->read_opcode =SPINOR_OP_RDSFDP ; nor->addr_nbytes =3 ; nor->read_dummy =8 ; ret =spi_nor_read_raw (nor, addr, len, buf); - nor->addr_nbytes = addr_nbytes;/* Restore setup to its uninitialized state. */ + nor->addr_nbytes =0 ; nor->read_opcode =0 ; nor->read_dummy =0 ;@@ -461,11 +458,11 @@ static int spi_nor_parse_bfpt(struct spi_nor *nor,switch (bfpt.dwords[BFPT_DWORD (1 )] &BFPT_DWORD1_ADDRESS_BYTES_MASK ) {case BFPT_DWORD1_ADDRESS_BYTES_3_ONLY :case BFPT_DWORD1_ADDRESS_BYTES_3_OR_4 : - nor->addr_nbytes =3 ; + params->addr_nbytes =3 ;break ;case BFPT_DWORD1_ADDRESS_BYTES_4_ONLY : - nor->addr_nbytes =4 ; + params->addr_nbytes =4 ;break ;default :@@ -652,7 +649,7 @@ static u8 spi_nor_smpt_addr_nbytes(const struct spi_nor *nor, const u32 settingsreturn 4 ;case SMPT_CMD_ADDRESS_LEN_USE_CURRENT :default : -return nor->addr_nbytes; +return nor->params->addr_nbytes; } }@@ -689,7 +686,6 @@ static const u32 *spi_nor_get_map_in_use(struct spi_nor *nor, const u32 *smpt,u32 addr;int err;u8 i; -u8 addr_nbytes;u8 read_data_mask, map_id;/* Use a kmalloc'ed bounce buffer to guarantee it is DMA-able. */ @@ -697,8 +693,6 @@ static const u32 *spi_nor_get_map_in_use(struct spi_nor *nor, const u32 *smpt,if (!buf)return ERR_PTR (-ENOMEM ); - addr_nbytes = nor->addr_nbytes; - map_id =0 ;/* Determine if there are any optional Detection Command Descriptors */ for (i =0 ; i < smpt_len; i +=2 ) {
drivers/mtd/spi-nor/sfdp.c static const u32 *spi_nor_get_map_in_use(struct spi_nor *nor, const u32 *smpt, · line 751
Quoted 6 lines
drivers/mtd/spi-nor/sfdp.c +1
-1@@ -753,8 +747,8 @@ static const u32 *spi_nor_get_map_in_use(struct spi_nor *nor, const u32 *smpt,/* fall through */ out:kfree (buf); - nor->addr_nbytes = addr_nbytes;/* Restore setup to its uninitialized state. */ + nor->addr_nbytes =0 ;
Same as before, I don't think this function should know or care about the default or uninitialised values.
drivers/mtd/spi-nor/sfdp.c static int spi_nor_parse_4bait(struct spi_nor *nor, · line 1093
Quoted 9 lines
drivers/mtd/spi-nor/sfdp.c +1
-1nor->read_dummy =0 ; nor->read_opcode =0 ;return ret;@@ -1096,7 +1090,7 @@ static int spi_nor_parse_4bait(struct spi_nor *nor,* Spansion memory. However this quirk is no longer needed with new * SFDP compliant memories. */ - nor->addr_nbytes =4 ; + params->addr_nbytes =4 ;
Patch looks good at first glance but I have not looked very carefully if it might cause some small issues.
Quoted 6 lines
drivers/mtd/spi-nor/sfdp.c +0
-0nor->flags |=SNOR_F_4B_OPCODES |SNOR_F_HAS_4BAIT ;/* fall through */ Signature · 1 line
2.25.1
issi.c's is25lp256_post_bfpt_fixups() also sets nor->addr_nbytes. Should that be updated to use params->addr_nbytes instead?
Signature · 7 lines
Regards, Pratyush Yadav Texas Instruments Inc. ______________________________________________________ Linux MTD discussion mailing list http://lists.infradead.org/mailman/listinfo/linux-mtd/
Re: [PATCH v15 4/8] mtd: spi-nor: Do not change nor->addr_nbytes at SFDP parsing time
Quoted 2 lines · Pratyush Yadav
issi.c's
is25lp256_post_bfpt_fixups()also setsnor->addr_nbytes. Should that be updated to useparams->addr_nbytesinstead?
Yes, it should, good catch! I've revisited this patch, otherwise it looks good.
ta
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
Re: [PATCH v15 4/8] mtd: spi-nor: Do not change nor->addr_nbytes at SFDP parsing time
In reply to Pratyush YadavQuoted 125 lines · Pratyush Yadav
EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
Quoted 5 lines · On 10/05/22 07:10AM, [email protected] wrote:
From: Tudor Ambarus <[email protected]>
At the SFDP parsing time we should not change members of struct
spi_nor, but instead fill members of structspi_nor_flash_parameterswhich could leter on be used by callers. The caller will then decide if SFDP paramss/leter/later/
Quoted 114 lines
should be used and more importantly when they should be used. Clean the code flow and don't initialize
nor->addr_nbytesat SFDP parsing time.Signed-off-by Tudor Ambarus <[email protected]>Tested-by Takahiro Kuwano <[email protected]>--- drivers/mtd/spi-nor/core.c | 5 ++--- drivers/mtd/spi-nor/core.h | 2 ++ drivers/mtd/spi-nor/sfdp.c | 18 ++++++------------ 3 files changed, 10 insertions(+), 15 deletions(-)drivers/mtd/spi-nor/core.c +2
-3@@ -2272,8 +2272,8 @@ static int spi_nor_default_setup(struct spi_nor *nor,static int spi_nor_set_addr_nbytes (struct spi_nor *nor) { -if (nor->addr_nbytes) { -/* already configured from SFDP */ +if (nor->params->addr_nbytes) { + nor->addr_nbytes = nor->params->addr_nbytes; }else if (nor->read_proto ==SNOR_PROTO_8_8_8_DTR ) {/* * In 8D-8D-8D mode, one byte takes half a cycle to transfer. So @@ -2518,7 +2518,6 @@ static void spi_nor_sfdp_init_params_deprecated(struct spi_nor *nor)if (spi_nor_parse_sfdp (nor)) {memcpy (nor->params, &sfdp_params,sizeof (*nor->params)); - nor->addr_nbytes =0 ; nor->flags &= ~SNOR_F_4B_OPCODES ; } }drivers/mtd/spi-nor/core.h +2
-0@@ -345,6 +345,7 @@ struct spi_nor_otp {* @writesize Minimal writable flash unit size. Defaults to 1. Set to * ECC unit size for ECC-ed flashes. * @page_size: the page size of the SPI NOR flash memory. +* @addr_nbytes: number of address bytes to send. * @rdsr_dummy: dummy cycles needed for Read Status Register command * in octal DTR mode. * @rdsr_addr_nbytes: dummy address bytes needed for Read Status Register @@ -377,6 +378,7 @@ struct spi_nor_flash_parameter {u64 size;u32 writesize;u32 page_size; +u8 addr_nbytes;u8 rdsr_dummy;u8 rdsr_addr_nbytes;drivers/mtd/spi-nor/sfdp.c +4
-8@@ -178,19 +178,16 @@ static int spi_nor_read_raw(struct spi_nor *nor, u32 addr, size_t len, u8 *buf)static int spi_nor_read_sfdp (struct spi_nor *nor,u32 addr,size_t len,void *buf) { -u8 addr_nbytes;int ret; - addr_nbytes = nor->addr_nbytes; - nor->read_opcode =SPINOR_OP_RDSFDP ; nor->addr_nbytes =3 ; nor->read_dummy =8 ; ret =spi_nor_read_raw (nor, addr, len, buf); - nor->addr_nbytes = addr_nbytes;/* Restore setup to its uninitialized state. */ + nor->addr_nbytes =0 ; nor->read_opcode =0 ; nor->read_dummy =0 ;@@ -461,11 +458,11 @@ static int spi_nor_parse_bfpt(struct spi_nor *nor,switch (bfpt.dwords[BFPT_DWORD (1 )] &BFPT_DWORD1_ADDRESS_BYTES_MASK ) {case BFPT_DWORD1_ADDRESS_BYTES_3_ONLY :case BFPT_DWORD1_ADDRESS_BYTES_3_OR_4 : - nor->addr_nbytes =3 ; + params->addr_nbytes =3 ;break ;case BFPT_DWORD1_ADDRESS_BYTES_4_ONLY : - nor->addr_nbytes =4 ; + params->addr_nbytes =4 ;break ;default :@@ -652,7 +649,7 @@ static u8 spi_nor_smpt_addr_nbytes(const struct spi_nor *nor, const u32 settingsreturn 4 ;case SMPT_CMD_ADDRESS_LEN_USE_CURRENT :default : -return nor->addr_nbytes; +return nor->params->addr_nbytes; } }@@ -689,7 +686,6 @@ static const u32 *spi_nor_get_map_in_use(struct spi_nor *nor, const u32 *smpt,u32 addr;int err;u8 i; -u8 addr_nbytes;u8 read_data_mask, map_id;/* Use a kmalloc'ed bounce buffer to guarantee it is DMA-able. */ @@ -697,8 +693,6 @@ static const u32 *spi_nor_get_map_in_use(struct spi_nor *nor, const u32 *smpt,if (!buf)return ERR_PTR (-ENOMEM );
Quoted 16 lines
drivers/mtd/spi-nor/sfdp.c static const u32 *spi_nor_get_map_in_use(struct spi_nor *nor, const u32 *smpt, · line 751
Quoted 12 lines
drivers/mtd/spi-nor/sfdp.c +1
-3- addr_nbytes = nor->addr_nbytes; - map_id =0 ;/* Determine if there are any optional Detection Command Descriptors */ for (i =0 ; i < smpt_len; i +=2 ) {@@ -753,8 +747,8 @@ static const u32 *spi_nor_get_map_in_use(struct spi_nor *nor, const u32 *smpt,/* fall through */ out:kfree (buf); - nor->addr_nbytes = addr_nbytes;/* Restore setup to its uninitialized state. */ + nor->addr_nbytes =0 ;Same as before, I don't think this function should know or care about the default or uninitialised values.
well, maybe. nor->addr_nbytes comes with value zero when this method is called. We gratuitously save it's zero value in a local variable and then we restore it. The restore of the value could signify to the reader that nor->addr_nbytes is already initialized with a sane value, which is not the case, so I find the code more readable in my version. But I don't mind too much, so I'll drop this particular change.
Thanks,
ta
Quoted 20 lines
drivers/mtd/spi-nor/sfdp.c static int spi_nor_parse_4bait(struct spi_nor *nor, · line 1093
Quoted 9 lines
drivers/mtd/spi-nor/sfdp.c +1
-1nor->read_dummy =0 ; nor->read_opcode =0 ;return ret;@@ -1096,7 +1090,7 @@ static int spi_nor_parse_4bait(struct spi_nor *nor,* Spansion memory. However this quirk is no longer needed with new * SFDP compliant memories. */ - nor->addr_nbytes =4 ; + params->addr_nbytes =4 ;Patch looks good at first glance but I have not looked very carefully if it might cause some small issues.
Quoted 6 lines
drivers/mtd/spi-nor/sfdp.c +0
-1nor->flags |=SNOR_F_4B_OPCODES |SNOR_F_HAS_4BAIT ;/* fall through */ --2.25.1
Quoted 7 lines
issi.c's
is25lp256_post_bfpt_fixups()also setsnor->addr_nbytes. Should that be updated to useparams->addr_nbytesinstead?--
Regards,
Pratyush Yadav
Texas Instruments Inc.
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
PATCH v15 5/8 mtd: spi-nor: core: Couple the number of address bytes with the address mode
In reply to [email protected]From: Tudor Ambarus <[email protected]>
Some of Infineon chips support volatile version of configuration registers and it is recommended to update volatile registers in the field application due to a risk of the non-volatile registers corruption by power interrupt. Such a volatile configuration register is used to enable the Quad mode. The register write sequence requires the number of bytes of address in order to be programmed. As it was before, the nor->addr_nbytes was set to 4 before calling the volatile Quad enable method. This was incorrect because the Write Any Register command does not have a 4B opcode equivalent and the address mode was still at default (3-byte mode) and not changed to 4 by entering in the 4 Byte Address Mode, so the operation failed.
Move the setting of the number of bytes of address after the Quad Enable method to allow reads or writes to registers that require the number of address bytes to work with the default address mode. The number of address bytes and the address mode are tightly coupled, this is a natural change.
Other (standard) Quad Enable methods are not affected, as they don't require the number of address bytes, so no functionality changes expected.
--- drivers/mtd/spi-nor/core.c | 134 +++++++++++++++++++------------------ 1 file changed, 70 insertions(+), 64 deletions(-)
drivers/mtd/spi-nor/core.c +70 -64
@@ -2270,49 +2270,6 @@ static int spi_nor_default_setup(struct spi_nor *nor,return 0 ; } -static int spi_nor_set_addr_nbytes (struct spi_nor *nor) -{ -if (nor->params->addr_nbytes) { - nor->addr_nbytes = nor->params->addr_nbytes; - }else if (nor->read_proto ==SNOR_PROTO_8_8_8_DTR ) { -/* -* In 8D-8D-8D mode, one byte takes half a cycle to transfer. So -* in this protocol an odd address width cannot be used because -* then the address phase would only span a cycle and a half. -* Half a cycle would be left over. We would then have to start -* the dummy phase in the middle of a cycle and so too the data -* phase, and we will end the transaction with half a cycle left -* over. -* -* Force all 8D-8D-8D flashes to use an address width of 4 to -* avoid this situation. -*/ - nor->addr_nbytes =4 ; - }else if (nor->info->addr_nbytes) { - nor->addr_nbytes = nor->info->addr_nbytes; - }else { - nor->addr_nbytes =3 ; - } - -if (nor->addr_nbytes ==3 && nor->params->size >0x1000000 ) { -/* enable 4-byte addressing if the device exceeds 16MiB */ - nor->addr_nbytes =4 ; - } - -if (nor->addr_nbytes >SPI_NOR_MAX_ADDR_NBYTES ) { -dev_dbg (nor->dev,"address width is too large: %u\n" , - nor->addr_nbytes); -return -EINVAL ; - } - -/* Set 4byte opcodes when possible. */ -if (nor->addr_nbytes ==4 && nor->flags &SNOR_F_4B_OPCODES && - !(nor->flags &SNOR_F_HAS_4BAIT )) -spi_nor_set_4byte_opcodes (nor); - -return 0 ; -} -static int spi_nor_setup (struct spi_nor *nor,const struct spi_nor_hwcaps *hwcaps) {
@@ -2322,10 +2279,7 @@ static int spi_nor_setup(struct spi_nor *nor, ret = nor->params->setup (nor, hwcaps); else ret =spi_nor_default_setup (nor, hwcaps); -if (ret) -return ret; - -return spi_nor_set_addr_nbytes (nor); +return ret; }/**
@@ -2707,6 +2661,74 @@ static int spi_nor_quad_enable(struct spi_nor *nor)return nor->params->quad_enable (nor); } +static int spi_nor_set_addr_nbytes (struct spi_nor *nor) +{ +if (nor->params->addr_nbytes) { + nor->addr_nbytes = nor->params->addr_nbytes; + }else if (nor->read_proto ==SNOR_PROTO_8_8_8_DTR ) { +/* +* In 8D-8D-8D mode, one byte takes half a cycle to transfer. So +* in this protocol an odd address width cannot be used because +* then the address phase would only span a cycle and a half. +* Half a cycle would be left over. We would then have to start +* the dummy phase in the middle of a cycle and so too the data +* phase, and we will end the transaction with half a cycle left +* over. +* +* Force all 8D-8D-8D flashes to use an address width of 4 to +* avoid this situation. +*/ + nor->addr_nbytes =4 ; + }else if (nor->info->addr_nbytes) { + nor->addr_nbytes = nor->info->addr_nbytes; + }else { + nor->addr_nbytes =3 ; + } + +if (nor->addr_nbytes ==3 && nor->params->size >0x1000000 ) { +/* enable 4-byte addressing if the device exceeds 16MiB */ + nor->addr_nbytes =4 ; + } + +if (nor->addr_nbytes >SPI_NOR_MAX_ADDR_NBYTES ) { +dev_dbg (nor->dev,"address width is too large: %u\n" , + nor->addr_nbytes); +return -EINVAL ; + } + +/* Set 4byte opcodes when possible. */ +if (nor->addr_nbytes ==4 && nor->flags &SNOR_F_4B_OPCODES && + !(nor->flags &SNOR_F_HAS_4BAIT )) +spi_nor_set_4byte_opcodes (nor); + +return 0 ; +} + +static int spi_nor_set_addr_mode (struct spi_nor *nor) +{ +int ret; + + ret =spi_nor_set_addr_nbytes (nor); +if (ret) +return ret; + +if (nor->addr_nbytes ==4 && nor->read_proto !=SNOR_PROTO_8_8_8_DTR && + !(nor->flags &SNOR_F_4B_OPCODES )) { +/* +* If the RESET# pin isn't hooked up properly, or the system +* otherwise doesn't perform a reset command in the boot +* sequence, it's impossible to 100% protect against unexpected +* reboots (e.g., crashes). Warn the user (or hopefully, system +* designer) that this is bad. +*/ +WARN_ONCE (nor->flags &SNOR_F_BROKEN_RESET , +"enabling reset hack; may not recover from unexpected reboots\n" ); + nor->params->set_4byte_addr_mode (nor, true); + } + +return 0 ; +} +static int spi_nor_init (struct spi_nor *nor) {int err;
@@ -2738,22 +2760,7 @@ static int spi_nor_init(struct spi_nor *nor) nor->flags & SNOR_F_SWP_IS_VOLATILE))spi_nor_try_unlock_all (nor); -if (nor->addr_nbytes ==4 && - nor->read_proto !=SNOR_PROTO_8_8_8_DTR && - !(nor->flags &SNOR_F_4B_OPCODES )) { -/* -* If the RESET# pin isn't hooked up properly, or the system -* otherwise doesn't perform a reset command in the boot -* sequence, it's impossible to 100% protect against unexpected -* reboots (e.g., crashes). Warn the user (or hopefully, system -* designer) that this is bad. -*/ -WARN_ONCE (nor->flags &SNOR_F_BROKEN_RESET , -"enabling reset hack; may not recover from unexpected reboots\n" ); - nor->params->set_4byte_addr_mode (nor, true); - } - -return 0 ; +return spi_nor_set_addr_mode (nor); }/**
@@ -3014,7 +3021,6 @@ int spi_nor_scan(struct spi_nor *nor, const char *name,* - select op codes for (Fast) Read, Page Program and Sector Erase. * - set the number of dummy cycles (mode cycles + wait states). * - set the SPI protocols for register and memory accesses. -* - set the address width. */ ret =spi_nor_setup (nor, hwcaps);if (ret)
Signature · 6 lines
2.25.1 ______________________________________________________ Linux MTD discussion mailing list http://lists.infradead.org/mailman/listinfo/linux-mtd/
Re: [PATCH v15 5/8] mtd: spi-nor: core: Couple the number of address bytes with the address mode
Am 2022-05-10 00:10, schrieb [email protected]:
Quoted 164 lines
From: Tudor Ambarus <[email protected]>
Some of Infineon chips support volatile version of configuration registers and it is recommended to update volatile registers in the field application due to a risk of the non-volatile registers corruption by power interrupt. Such a volatile configuration register is used to enable the Quad mode. The register write sequence requires the number of bytes of address in order to be programmed. As it was before, the
nor->addr_nbyteswas set to 4 before calling the volatile Quad enable method. This was incorrect because the Write Any Register command does not have a 4B opcode equivalent and the address mode was still at default (3-byte mode) and not changed to 4 by entering in the 4 Byte Address Mode, so the operation failed.Move the setting of the number of bytes of address after the Quad Enable method to allow reads or writes to registers that require the number of address bytes to work with the default address mode. The number of address bytes and the address mode are tightly coupled, this is a natural change.
Other (standard) Quad Enable methods are not affected, as they don't require the number of address bytes, so no functionality changes expected.
Reported-by Takahiro Kuwano <[email protected]>Signed-off-by Tudor Ambarus <[email protected]>Tested-by Takahiro Kuwano <[email protected]>--- drivers/mtd/spi-nor/core.c | 134 +++++++++++++++++++------------------ 1 file changed, 70 insertions(+), 64 deletions(-)drivers/mtd/spi-nor/core.c +0
-43@@ -2270,49 +2270,6 @@ static int spi_nor_default_setup(struct spi_nor *nor, return 0; } -static int spi_nor_set_addr_nbytes (struct spi_nor *nor) -{ -if (nor->params->addr_nbytes) { - nor->addr_nbytes = nor->params->addr_nbytes; - }else if (nor->read_proto ==SNOR_PROTO_8_8_8_DTR ) { -/* -* In 8D-8D-8D mode, one byte takes half a cycle to transfer. So -* in this protocol an odd address width cannot be used because -* then the address phase would only span a cycle and a half. -* Half a cycle would be left over. We would then have to start -* the dummy phase in the middle of a cycle and so too the data -* phase, and we will end the transaction with half a cycle left -* over. -* -* Force all 8D-8D-8D flashes to use an address width of 4 to -* avoid this situation. -*/ - nor->addr_nbytes =4 ; - }else if (nor->info->addr_nbytes) { - nor->addr_nbytes = nor->info->addr_nbytes; - }else { - nor->addr_nbytes =3 ; - } - -if (nor->addr_nbytes ==3 && nor->params->size >0x1000000 ) { -/* enable 4-byte addressing if the device exceeds 16MiB */ - nor->addr_nbytes =4 ; - } - -if (nor->addr_nbytes >SPI_NOR_MAX_ADDR_NBYTES ) { -dev_dbg (nor->dev,"address width is too large: %u\n" , - nor->addr_nbytes); -return -EINVAL ; - } - -/* Set 4byte opcodes when possible. */ -if (nor->addr_nbytes ==4 && nor->flags &SNOR_F_4B_OPCODES && - !(nor->flags &SNOR_F_HAS_4BAIT )) -spi_nor_set_4byte_opcodes (nor); - -return 0 ; -} -static int spi_nor_setup (struct spi_nor *nor,const struct spi_nor_hwcaps *hwcaps){
drivers/mtd/spi-nor/core.c +53
-4@@ -2322,10 +2279,7 @@ static int spi_nor_setup(struct spi_nor *nor, ret = nor->params->setup (nor, hwcaps); else ret =spi_nor_default_setup (nor, hwcaps); -if (ret) -return ret; - -return spi_nor_set_addr_nbytes (nor); +return ret; }/** @@ -2707,6 +2661,74 @@ static int spi_nor_quad_enable(struct spi_nor *nor)return nor->params->quad_enable (nor); } +static int spi_nor_set_addr_nbytes (struct spi_nor *nor) +{ +if (nor->params->addr_nbytes) { + nor->addr_nbytes = nor->params->addr_nbytes; + }else if (nor->read_proto ==SNOR_PROTO_8_8_8_DTR ) { +/* +* In 8D-8D-8D mode, one byte takes half a cycle to transfer. So +* in this protocol an odd address width cannot be used because +* then the address phase would only span a cycle and a half. +* Half a cycle would be left over. We would then have to start +* the dummy phase in the middle of a cycle and so too the data +* phase, and we will end the transaction with half a cycle left +* over. +* +* Force all 8D-8D-8D flashes to use an address width of 4 to +* avoid this situation. +*/ + nor->addr_nbytes =4 ; + }else if (nor->info->addr_nbytes) { + nor->addr_nbytes = nor->info->addr_nbytes; + }else { + nor->addr_nbytes =3 ; + } + +if (nor->addr_nbytes ==3 && nor->params->size >0x1000000 ) { +/* enable 4-byte addressing if the device exceeds 16MiB */ + nor->addr_nbytes =4 ; + } + +if (nor->addr_nbytes >SPI_NOR_MAX_ADDR_NBYTES ) { +dev_dbg (nor->dev,"address width is too large: %u\n" , + nor->addr_nbytes); +return -EINVAL ; + } + +/* Set 4byte opcodes when possible. */ +if (nor->addr_nbytes ==4 && nor->flags &SNOR_F_4B_OPCODES && + !(nor->flags &SNOR_F_HAS_4BAIT )) +spi_nor_set_4byte_opcodes (nor); + +return 0 ; +} + +static int spi_nor_set_addr_mode (struct spi_nor *nor) +{ +int ret; + + ret =spi_nor_set_addr_nbytes (nor); +if (ret) +return ret; + + if (nor->addr_nbytes == 4 && nor->read_proto != SNOR_PROTO_8_8_8_DTR&&
drivers/mtd/spi-nor/core.c +10
-0+ !(nor->flags & SNOR_F_4B_OPCODES)) { +/* +* If the RESET# pin isn't hooked up properly, or the system +* otherwise doesn't perform a reset command in the boot +* sequence, it's impossible to 100% protect against unexpected +* reboots (e.g., crashes). Warn the user (or hopefully, system +* designer) that this is bad. +*/ + WARN_ONCE(nor->flags & SNOR_F_BROKEN_RESET, + "enabling reset hack; may not recover from unexpectedreboots\n");
drivers/mtd/spi-nor/core.c static int spi_nor_quad_enable(struct spi_nor *nor) · line 2726
Quoted 1 line
drivers/mtd/spi-nor/core.c +1
-0+ nor->params->set_4byte_addr_mode (nor, true);
Why don't we check the return code here? I know it was this way before, but that looks wrong.
-michael
Quoted 41 lines
drivers/mtd/spi-nor/core.c +6
-16+ } + +return 0 ; +} +static int spi_nor_init (struct spi_nor *nor) {int err;@@ -2738,22 +2760,7 @@ static int spi_nor_init(struct spi_nor *nor) nor->flags & SNOR_F_SWP_IS_VOLATILE)) spi_nor_try_unlock_all(nor); -if (nor->addr_nbytes ==4 && - nor->read_proto !=SNOR_PROTO_8_8_8_DTR && - !(nor->flags &SNOR_F_4B_OPCODES )) { -/* -* If the RESET# pin isn't hooked up properly, or the system -* otherwise doesn't perform a reset command in the boot -* sequence, it's impossible to 100% protect against unexpected -* reboots (e.g., crashes). Warn the user (or hopefully, system -* designer) that this is bad. -*/ -WARN_ONCE (nor->flags &SNOR_F_BROKEN_RESET , -"enabling reset hack; may not recover from unexpected reboots\n"); - nor->params->set_4byte_addr_mode (nor, true); - } - -return 0 ; +return spi_nor_set_addr_mode (nor); }/**
drivers/mtd/spi-nor/core.c +0
-1@@ -3014,7 +3021,6 @@ int spi_nor_scan(struct spi_nor *nor, const char*name, * - select op codes for (Fast) Read, Page Program and Sector Erase. * - set the number of dummy cycles (mode cycles + wait states). * - set the SPI protocols for register and memory accesses. -* - set the address width. */ ret =spi_nor_setup (nor, hwcaps);
Quoted 1 line
if (ret)
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
PATCH v15 6/8 mtd: spi-nor: Retain nor->addr_width at 4BAIT parse
In reply to [email protected]From: Takahiro Kuwano <[email protected]>
In 4BAIT parse, keep nor->params->addr_width because it may be used as current address mode in SMPT parse later on.
--- drivers/mtd/spi-nor/core.c | 2 ++ drivers/mtd/spi-nor/sfdp.c | 1 - 2 files changed, 2 insertions(+), 1 deletion(-)
drivers/mtd/spi-nor/core.c +2 -0
@@ -2664,6 +2664,8 @@ static int spi_nor_quad_enable(struct spi_nor *nor)static int spi_nor_set_addr_nbytes (struct spi_nor *nor) {if (nor->params->addr_nbytes) { +if (nor->flags &SNOR_F_HAS_4BAIT ) + nor->params->addr_nbytes =4 ; nor->addr_nbytes = nor->params->addr_nbytes; }else if (nor->read_proto ==SNOR_PROTO_8_8_8_DTR ) {/*
drivers/mtd/spi-nor/sfdp.c +0 -1
@@ -1090,7 +1090,6 @@ static int spi_nor_parse_4bait(struct spi_nor *nor,* Spansion memory. However this quirk is no longer needed with new * SFDP compliant memories. */ - params->addr_nbytes =4 ; nor->flags |=SNOR_F_4B_OPCODES |SNOR_F_HAS_4BAIT ;/* fall through */
Signature · 6 lines
2.25.1 ______________________________________________________ Linux MTD discussion mailing list http://lists.infradead.org/mailman/listinfo/linux-mtd/
Re: [PATCH v15 6/8] mtd: spi-nor: Retain nor->addr_width at 4BAIT parse
Am 2022-05-10 00:10, schrieb [email protected]:
Quoted 4 lines
From: Takahiro Kuwano <[email protected]>
In 4BAIT parse, keep
nor->params->addr_widthbecause it may be used as current address mode in SMPT parse later on.
Mh I'm not sure this is needed at all.
SFDP spec says
Variable address length (the current setting of the address length mode defines the address length)
and
When the length is defined as variable, the software or hardware controlling the memory is aware of the address length mode last set in the memory device and this same length of address.
We don't set any address mode until all the SFDP parsing is over. Therefore we should always be in 3 byte mode, no?
-michael
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
Re: [PATCH v15 6/8] mtd: spi-nor: Retain nor->addr_width at 4BAIT parse
Quoted 12 lines · Michael Walle
Am 2022-05-10 00:10, schrieb [email protected]:
Quoted 4 lines
From: Takahiro Kuwano <[email protected]>
In 4BAIT parse, keep
nor->params->addr_widthbecause it may be used as current address mode in SMPT parse later on.Mh I'm not sure this is needed at all.
SFDP spec says
Variable address length (the current setting of the address length mode defines the address length)
Quoted 8 lines
and
When the length is defined as variable, the software or hardware controlling the memory is aware of the address length mode last set in the memory device and this same length of address.We don't set any address mode until all the SFDP parsing is over. Therefore we should always be in 3 byte mode, no?
Actually there are some devices that have variable address length but 4 byte mode by default (I will work on those devices after this series is settled). To support such case, I prefer to use params->addr_nbytes as current address mode so that I can fix it in post_bfpt_fixup() hook.
Thanks,
Takahiro
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
Re: [PATCH v15 6/8] mtd: spi-nor: Retain nor->addr_width at 4BAIT parse
[btw the subject still has the old name of the addr_width]
Am 2022-05-13 03:26, schrieb Takahiro Kuwano:
Quoted 18 lines · Michael Walle
Quoted 17 lines
Am 2022-05-10 00:10, schrieb [email protected]:
Quoted 4 lines
From: Takahiro Kuwano <[email protected]>
In 4BAIT parse, keep
nor->params->addr_widthbecause it may be used as current address mode in SMPT parse later on.Mh I'm not sure this is needed at all.
SFDP spec says
Variable address length (the current setting of the address length mode defines the address length)and
When the length is defined as variable, the software or hardware controlling the memory is aware of the address length mode last set in the memory device and this same length of address.
Quoted 7 lines
Quoted 3 lines
We don't set any address mode until all the SFDP parsing is over. Therefore we should always be in 3 byte mode, no?
Actually there are some devices that have variable address length but 4 byte mode by default (I will work on those devices after this series is settled). To support such case, I prefer to use
params->addr_nbytesas current address mode so that I can fix it inpost_bfpt_fixup()hook.
Are there public datasheets available? So these devices have a 3 byte and a 4 byte mode, but after reset, they are in the 4 byte mode? Looks like it should be fixed in a different way. I'm not sure the "current mode" handling is correct.
We need to differentiate between the mode the flash currently is using (nor->addr_nbytes) and the mode parsed by SFDP (params->addr_nbytes).
At some point, the mode is switched and nor->addr_nbytes becomes params->addr_nbytes. It seems in your case nor->addr_nbytes should be 4 right from the beginning. Which also means nor->addr_nbytes should be 3 for the other cases (and probably not 0).
-michael
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
Re: [PATCH v15 6/8] mtd: spi-nor: Retain nor->addr_width at 4BAIT parse
Quoted 2 lines · Michael Walle
[btw the subject still has the old name of the
addr_width]
Yes, it must be fixed in next rev.
Quoted 22 lines
Am 2022-05-13 03:26, schrieb Takahiro Kuwano:
Quoted 21 lines · Michael Walle
Quoted 20 lines
Am 2022-05-10 00:10, schrieb [email protected]:
Quoted 4 lines
From: Takahiro Kuwano <[email protected]>
In 4BAIT parse, keep
nor->params->addr_widthbecause it may be used as current address mode in SMPT parse later on.Mh I'm not sure this is needed at all.
SFDP spec says
Variable address length (the current setting of the address length mode defines the address length)and
When the length is defined as variable, the software or hardware controlling the memory is aware of the address length mode last set in the memory device and this same length of address.We don't set any address mode until all the SFDP parsing is over. Therefore we should always be in 3 byte mode, no?
Quoted 6 lines
Quoted 4 lines
Actually there are some devices that have variable address length but 4 byte mode by default (I will work on those devices after this series is settled). To support such case, I prefer to use
params->addr_nbytesas current address mode so that I can fix it inpost_bfpt_fixup()hook.Are there public datasheets available? So these devices have a 3 byte
I will send datasheets to you in another email. At this point, only summary datasheet is available in website.
Quoted 1 line
and a 4 byte mode, but after reset, they are in the 4 byte mode? Looks
Yes.
Quoted 3 lines
like it should be fixed in a different way. I'm not sure the "current mode" handling is correct.
Yes, we may want to introduce a new flag like SPI_NOR_4BAM_DEFAULT and check the flag in BFPT parse. Once I send another series, please review.
Quoted 3 lines
We need to differentiate between the mode the flash currently is using (
nor->addr_nbytes) and the mode parsed by SFDP (params->addr_nbytes).
The flash's address mode affects the address length of Non-4B opcodes, including read/write any register ops used in SMPT parse and Infineon (spansion) specific hooks.
The 4B opcodes always take address length of 4 regardless of flash's address mode. In these Infineon chips, 4B opcodes for read/program/ erase are available and 4BAIT advertises them. We don't have to enter 4 byte address mode for read/program/erase.
So, I think we need to differentiate between address length for read/program/erase and flash's default address mode.
Obviously we are using nor->addr_nbytes as address length for read/ program/erase and should keep this usage.
For flash's default address mode, my preference is to use params->addr_nbytes, but I should rename it to something like params->def_addr_nbytes and rework spi_nor_set_addr_nbytes().
static int spi_nor_set_addr_nbytes(struct spi_nor *nor)
{
if (nor->flags & SNOR_F_HAS_4BAIT) {
nor->addr_nbytes = 4;
} else if (nor->params->def_addr_nbytes) { nor->addr_nbytes = nor->params->def_addr_nbytes;
Quoted 5 lines
At some point, the mode is switched and
nor->addr_nbytesbecomesparams->addr_nbytes. It seems in your casenor->addr_nbytesshould be 4 right from the beginning. Which also meansnor->addr_nbytesshould be 3 for the other cases (and probably not 0).
With param->def_addr_nbytes, I think we can keep nor->addr_nbytes = 0 during SFDP parse.
Thanks,
Takahiro
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
Re: [PATCH v15 6/8] mtd: spi-nor: Retain nor->addr_width at 4BAIT parse
Hello,
Any comments on how to handle this?
Quoted 79 lines · Takahiro Kuwano
Quoted 2 lines · Michael Walle
[btw the subject still has the old name of the
addr_width]Yes, it must be fixed in next rev.
Quoted 22 lines
Am 2022-05-13 03:26, schrieb Takahiro Kuwano:
Quoted 21 lines · Michael Walle
Quoted 20 lines
Am 2022-05-10 00:10, schrieb [email protected]:
Quoted 4 lines
From: Takahiro Kuwano <[email protected]>
In 4BAIT parse, keep
nor->params->addr_widthbecause it may be used as current address mode in SMPT parse later on.Mh I'm not sure this is needed at all.
SFDP spec says
Variable address length (the current setting of the address length mode defines the address length)and
When the length is defined as variable, the software or hardware controlling the memory is aware of the address length mode last set in the memory device and this same length of address.We don't set any address mode until all the SFDP parsing is over. Therefore we should always be in 3 byte mode, no?
Quoted 6 lines
Quoted 4 lines
Actually there are some devices that have variable address length but 4 byte mode by default (I will work on those devices after this series is settled). To support such case, I prefer to use
params->addr_nbytesas current address mode so that I can fix it inpost_bfpt_fixup()hook.Are there public datasheets available? So these devices have a 3 byte
I will send datasheets to you in another email. At this point, only summary datasheet is available in website.
Quoted 1 line
and a 4 byte mode, but after reset, they are in the 4 byte mode? Looks
Yes.
Quoted 3 lines
like it should be fixed in a different way. I'm not sure the "current mode" handling is correct.
Yes, we may want to introduce a new flag like
SPI_NOR_4BAM_DEFAULTand check the flag in BFPT parse. Once I send another series, please review.Quoted 3 lines
We need to differentiate between the mode the flash currently is using (
nor->addr_nbytes) and the mode parsed by SFDP (params->addr_nbytes).The flash's address mode affects the address length of Non-4B opcodes, including read/write any register ops used in SMPT parse and Infineon (spansion) specific hooks.
The 4B opcodes always take address length of 4 regardless of flash's address mode. In these Infineon chips, 4B opcodes for read/program/ erase are available and 4BAIT advertises them. We don't have to enter 4 byte address mode for read/program/erase.
So, I think we need to differentiate between address length for read/program/erase and flash's default address mode.
Obviously we are using
nor->addr_nbytesas address length for read/ program/erase and should keep this usage.For flash's default address mode, my preference is to use
params->addr_nbytes, but I should rename it to something likeparams->def_addr_nbytesand reworkspi_nor_set_addr_nbytes().static int
spi_nor_set_addr_nbytes(struct spi_nor *nor){ if (nor->flags & SNOR_F_HAS_4BAIT) { nor->addr_nbytes = 4; } else if (nor->params->def_addr_nbytes) {
nor->addr_nbytes=nor->params->def_addr_nbytes;Quoted 5 lines
At some point, the mode is switched and
nor->addr_nbytesbecomesparams->addr_nbytes. It seems in your casenor->addr_nbytesshould be 4 right from the beginning. Which also meansnor->addr_nbytesshould be 3 for the other cases (and probably not 0).
Quoted 11 lines
With
param->def_addr_nbytes, I think we can keepnor->addr_nbytes= 0 during SFDP parse.Thanks,
Takahiro
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
Re: [PATCH v15 6/8] mtd: spi-nor: Retain nor->addr_width at 4BAIT parse
Hi,
Am 2022-05-18 08:04, schrieb Takahiro Kuwano:
Quoted 1 line
Any comments on how to handle this?
It's not even been a week since the former mail. Please give us some time :)
-michael
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
Re: [PATCH v15 6/8] mtd: spi-nor: Retain nor->addr_width at 4BAIT parse
Quoted 8 lines · Michael Walle
Hi,
Am 2022-05-18 08:04, schrieb Takahiro Kuwano:
Quoted 1 line
Any comments on how to handle this?
It's not even been a week since the former mail. Please give us some time :)
Sorry, I need to be more patient.
Thanks,
Takahiro
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
Re: [PATCH v15 6/8] mtd: spi-nor: Retain nor->addr_width at 4BAIT parse
In reply to Takahiro KuwanoAm 2022-05-14 05:51, schrieb Takahiro Kuwano:
Quoted 48 lines · Michael Walle
Quoted 2 lines
[btw the subject still has the old name of the
addr_width]Yes, it must be fixed in next rev.
Quoted 22 lines
Am 2022-05-13 03:26, schrieb Takahiro Kuwano:
Quoted 21 lines · Michael Walle
Quoted 20 lines
Am 2022-05-10 00:10, schrieb [email protected]:
Quoted 4 lines
From: Takahiro Kuwano <[email protected]>
In 4BAIT parse, keep
nor->params->addr_widthbecause it may be used as current address mode in SMPT parse later on.Mh I'm not sure this is needed at all.
SFDP spec says
Variable address length (the current setting of the address length mode defines the address length)and
When the length is defined as variable, the software or hardware controlling the memory is aware of the address length mode last set in the memory device and this same length of address.We don't set any address mode until all the SFDP parsing is over. Therefore we should always be in 3 byte mode, no?
Quoted 6 lines
Quoted 4 lines
Actually there are some devices that have variable address length but 4 byte mode by default (I will work on those devices after this series is settled). To support such case, I prefer to use
params->addr_nbytesas current address mode so that I can fix it inpost_bfpt_fixup()hook.Are there public datasheets available? So these devices have a 3 byte
I will send datasheets to you in another email. At this point, only summary datasheet is available in website.
Quoted 1 line
and a 4 byte mode, but after reset, they are in the 4 byte mode? Looks
Yes.
Quoted 3 lines
like it should be fixed in a different way. I'm not sure the "current mode" handling is correct.
Yes, we may want to introduce a new flag like
SPI_NOR_4BAM_DEFAULTand check the flag in BFPT parse. Once I send another series, please review.Quoted 3 lines
We need to differentiate between the mode the flash currently is using (
nor->addr_nbytes) and the mode parsed by SFDP (params->addr_nbytes).
Quoted 8 lines
The flash's address mode affects the address length of Non-4B opcodes, including read/write any register ops used in SMPT parse and Infineon (spansion) specific hooks.
The 4B opcodes always take address length of 4 regardless of flash's address mode. In these Infineon chips, 4B opcodes for read/program/ erase are available and 4BAIT advertises them. We don't have to enter 4 byte address mode for read/program/erase.
btw. this is a pity. you are using the stateless 4b opcodes but then you don't provide stateless opcodes for the read any register op :/
Quoted 2 lines
So, I think we need to differentiate between address length for read/program/erase and flash's default address mode.
Or we keep them in sync. E.g. switch to 4bytes mode if we are using the 4 byte. Granted, that sounds like a hack :)
Quoted 2 lines
Obviously we are using
nor->addr_nbytesas address length for read/ program/erase and should keep this usage.
Yes, I wasn't aware that we actually two different runtime parameters:
- the read/program/erase address width, also used with the 4b opcodes
- internal mode 3b/4b. Up until now, this wasn't an issue because either the mode was switched or the 4b opcodes were used. So this was mutually exclusive. Now we have flashes which uses 4b opcodes _and_ we need the state of the internal mode.
I can't think of a good solution for now. Need to think more about this, but I'm pretty busy at the moment. What I think is clear is that we need two different modes here in the spi_nor struct. nor->addr_nbytes for the read/program/erase opcodes and nor->address_mode or similar which tracks the SPI flash's internal address mode.
Quoted 3 lines
For flash's default address mode, my preference is to use
params->addr_nbytes, but I should rename it to something likeparams->def_addr_nbytesand reworkspi_nor_set_addr_nbytes().
IMHO params should only be used to store the parsed (or hardcoded) parameters.
-michael
Quoted 12 lines
static int
spi_nor_set_addr_nbytes(struct spi_nor *nor){ if (nor->flags & SNOR_F_HAS_4BAIT) { nor->addr_nbytes = 4; } else if (nor->params->def_addr_nbytes) {
nor->addr_nbytes=nor->params->def_addr_nbytes;Quoted 5 lines
At some point, the mode is switched and
nor->addr_nbytesbecomesparams->addr_nbytes. It seems in your casenor->addr_nbytesshould be 4 right from the beginning. Which also meansnor->addr_nbytesshould be 3 for the other cases (and probably not 0).
Quoted 5 lines
With
param->def_addr_nbytes, I think we can keepnor->addr_nbytes= 0 during SFDP parse.Thanks,
Takahiro
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
Re: [PATCH v15 6/8] mtd: spi-nor: Retain nor->addr_width at 4BAIT parse
Quoted 62 lines · Michael Walle
Am 2022-05-14 05:51, schrieb Takahiro Kuwano:
Quoted 48 lines · Michael Walle
Quoted 2 lines
[btw the subject still has the old name of the
addr_width]Yes, it must be fixed in next rev.
Quoted 22 lines
Am 2022-05-13 03:26, schrieb Takahiro Kuwano:
Quoted 21 lines · Michael Walle
Quoted 20 lines
Am 2022-05-10 00:10, schrieb [email protected]:
Quoted 4 lines
From: Takahiro Kuwano <[email protected]>
In 4BAIT parse, keep
nor->params->addr_widthbecause it may be used as current address mode in SMPT parse later on.Mh I'm not sure this is needed at all.
SFDP spec says
Variable address length (the current setting of the address length mode defines the address length)and
When the length is defined as variable, the software or hardware controlling the memory is aware of the address length mode last set in the memory device and this same length of address.We don't set any address mode until all the SFDP parsing is over. Therefore we should always be in 3 byte mode, no?
Quoted 6 lines
Quoted 4 lines
Actually there are some devices that have variable address length but 4 byte mode by default (I will work on those devices after this series is settled). To support such case, I prefer to use
params->addr_nbytesas current address mode so that I can fix it inpost_bfpt_fixup()hook.Are there public datasheets available? So these devices have a 3 byte
I will send datasheets to you in another email. At this point, only summary datasheet is available in website.
Quoted 1 line
and a 4 byte mode, but after reset, they are in the 4 byte mode? Looks
Yes.
Quoted 3 lines
like it should be fixed in a different way. I'm not sure the "current mode" handling is correct.
Yes, we may want to introduce a new flag like
SPI_NOR_4BAM_DEFAULTand check the flag in BFPT parse. Once I send another series, please review.Quoted 3 lines
We need to differentiate between the mode the flash currently is using (
nor->addr_nbytes) and the mode parsed by SFDP (params->addr_nbytes).Quoted 8 lines
The flash's address mode affects the address length of Non-4B opcodes, including read/write any register ops used in SMPT parse and Infineon (spansion) specific hooks.
The 4B opcodes always take address length of 4 regardless of flash's address mode. In these Infineon chips, 4B opcodes for read/program/ erase are available and 4BAIT advertises them. We don't have to enter 4 byte address mode for read/program/erase.
btw. this is a pity. you are using the stateless 4b opcodes but then you don't provide stateless opcodes for the read any register op :/
Quoted 6 lines
Quoted 2 lines
So, I think we need to differentiate between address length for read/program/erase and flash's default address mode.
Or we keep them in sync. E.g. switch to 4bytes mode if we are using the 4 byte. Granted, that sounds like a hack :)
Yes, the earlier revision of the series switched to 4byte mode in fixup hook, but we don't want to change device settings during SFDP parse.
Quoted 13 lines
Quoted 2 lines
Obviously we are using
nor->addr_nbytesas address length for read/ program/erase and should keep this usage.Yes, I wasn't aware that we actually two different runtime parameters:
- the read/program/erase address width, also used with the 4b opcodes
- internal mode 3b/4b. Up until now, this wasn't an issue because either the mode was switched or the 4b opcodes were used. So this was mutually exclusive. Now we have flashes which uses 4b opcodes _and_ we need the state of the internal mode.
Quoted 7 lines
I can't think of a good solution for now. Need to think more about this, but I'm pretty busy at the moment. What I think is clear is that we need two different modes here in the
spi_norstruct.nor->addr_nbytesfor the read/program/erase opcodes andnor->address_modeor similar which tracks the SPI flash's internal address mode.
So, until we come up with a good solution, can we directly use the address length of 3 in SMPT parse and vendor specific hooks? By doing that, we can remove this (6/8) and previous (5/8) patches (minimum change would be better as a temporary solution).
Quoted 7 lines
Quoted 3 lines
For flash's default address mode, my preference is to use
params->addr_nbytes, but I should rename it to something likeparams->def_addr_nbytesand reworkspi_nor_set_addr_nbytes().IMHO params should only be used to store the parsed (or hardcoded) parameters.
OK, understood.
Thanks,
Takahiro
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
Re: [PATCH v15 6/8] mtd: spi-nor: Retain nor->addr_width at 4BAIT parse
Any thoughts?
Quoted 103 lines · Takahiro Kuwano
Quoted 62 lines · Michael Walle
Am 2022-05-14 05:51, schrieb Takahiro Kuwano:
Quoted 48 lines · Michael Walle
Quoted 2 lines
[btw the subject still has the old name of the
addr_width]Yes, it must be fixed in next rev.
Quoted 22 lines
Am 2022-05-13 03:26, schrieb Takahiro Kuwano:
Quoted 21 lines · Michael Walle
Quoted 20 lines
Am 2022-05-10 00:10, schrieb [email protected]:
Quoted 4 lines
From: Takahiro Kuwano <[email protected]>
In 4BAIT parse, keep
nor->params->addr_widthbecause it may be used as current address mode in SMPT parse later on.Mh I'm not sure this is needed at all.
SFDP spec says
Variable address length (the current setting of the address length mode defines the address length)and
When the length is defined as variable, the software or hardware controlling the memory is aware of the address length mode last set in the memory device and this same length of address.We don't set any address mode until all the SFDP parsing is over. Therefore we should always be in 3 byte mode, no?
Quoted 6 lines
Quoted 4 lines
Actually there are some devices that have variable address length but 4 byte mode by default (I will work on those devices after this series is settled). To support such case, I prefer to use
params->addr_nbytesas current address mode so that I can fix it inpost_bfpt_fixup()hook.Are there public datasheets available? So these devices have a 3 byte
I will send datasheets to you in another email. At this point, only summary datasheet is available in website.
Quoted 1 line
and a 4 byte mode, but after reset, they are in the 4 byte mode? Looks
Yes.
Quoted 3 lines
like it should be fixed in a different way. I'm not sure the "current mode" handling is correct.
Yes, we may want to introduce a new flag like
SPI_NOR_4BAM_DEFAULTand check the flag in BFPT parse. Once I send another series, please review.Quoted 3 lines
We need to differentiate between the mode the flash currently is using (
nor->addr_nbytes) and the mode parsed by SFDP (params->addr_nbytes).Quoted 8 lines
The flash's address mode affects the address length of Non-4B opcodes, including read/write any register ops used in SMPT parse and Infineon (spansion) specific hooks.
The 4B opcodes always take address length of 4 regardless of flash's address mode. In these Infineon chips, 4B opcodes for read/program/ erase are available and 4BAIT advertises them. We don't have to enter 4 byte address mode for read/program/erase.
btw. this is a pity. you are using the stateless 4b opcodes but then you don't provide stateless opcodes for the read any register op :/
Quoted 6 lines
Quoted 2 lines
So, I think we need to differentiate between address length for read/program/erase and flash's default address mode.
Or we keep them in sync. E.g. switch to 4bytes mode if we are using the 4 byte. Granted, that sounds like a hack :)
Yes, the earlier revision of the series switched to 4byte mode in fixup hook, but we don't want to change device settings during SFDP parse.
Quoted 13 lines
Quoted 2 lines
Obviously we are using
nor->addr_nbytesas address length for read/ program/erase and should keep this usage.Yes, I wasn't aware that we actually two different runtime parameters:
- the read/program/erase address width, also used with the 4b opcodes
- internal mode 3b/4b. Up until now, this wasn't an issue because either the mode was switched or the 4b opcodes were used. So this was mutually exclusive. Now we have flashes which uses 4b opcodes _and_ we need the state of the internal mode.Quoted 7 lines
I can't think of a good solution for now. Need to think more about this, but I'm pretty busy at the moment. What I think is clear is that we need two different modes here in the
spi_norstruct.nor->addr_nbytesfor the read/program/erase opcodes andnor->address_modeor similar which tracks the SPI flash's internal address mode.So, until we come up with a good solution, can we directly use the address length of 3 in SMPT parse and vendor specific hooks? By doing that, we can remove this (6/8) and previous (5/8) patches (minimum change would be better as a temporary solution).
Quoted 4 lines
Quoted 3 lines
For flash's default address mode, my preference is to use
params->addr_nbytes, but I should rename it to something likeparams->def_addr_nbytesand reworkspi_nor_set_addr_nbytes().
Quoted 7 lines
Quoted 3 lines
IMHO params should only be used to store the parsed (or hardcoded) parameters.
OK, understood.
Thanks,
Takahiro
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
Re: [PATCH v15 6/8] mtd: spi-nor: Retain nor->addr_width at 4BAIT parse
In reply to Michael WalleQuoted 88 lines · Michael Walle
EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
Am 2022-05-14 05:51, schrieb Takahiro Kuwano:
Quoted 53 lines · Michael Walle
Quoted 2 lines
[btw the subject still has the old name of the
addr_width]Yes, it must be fixed in next rev.
Quoted 31 lines
Am 2022-05-13 03:26, schrieb Takahiro Kuwano:
Quoted 22 lines · Michael Walle
Quoted 13 lines
Am 2022-05-10 00:10, schrieb [email protected]:
Quoted 5 lines
From: Takahiro Kuwano <[email protected]>
In 4BAIT parse, keep
nor->params->addr_widthbecause it may be used as
current address mode in SMPT parse later on.Mh I'm not sure this is needed at all.
SFDP spec says
Variable address length (the current setting of the address length mode defines the address length)Quoted 8 lines
and
When the length is defined as variable, the software or hardware controlling the memory is aware of the address length mode last set in the memory device and this same length of address.We don't set any address mode until all the SFDP parsing is over. Therefore we should always be in 3 byte mode, no?
Quoted 7 lines
Actually there are some devices that have variable address length but 4 byte mode by default (I will work on those devices after this series
is settled). To support such case, I prefer to useparams->addr_nbytes
as current address mode so that I can fix it inpost_bfpt_fixup()hook.Quoted 1 line
Are there public datasheets available? So these devices have a 3 byte
I will send datasheets to you in another email. At this point, only summary datasheet is available in website.
Quoted 1 line
and a 4 byte mode, but after reset, they are in the 4 byte mode? Looks
Yes.
Quoted 3 lines
like it should be fixed in a different way. I'm not sure the "current mode" handling is correct.
Yes, we may want to introduce a new flag like
SPI_NOR_4BAM_DEFAULTand check
the flag in BFPT parse. Once I send another series, please review.Quoted 3 lines
We need to differentiate between the mode the flash currently is using (
nor->addr_nbytes) and the mode parsed by SFDP (params->addr_nbytes).Quoted 8 lines
The flash's address mode affects the address length of Non-4B opcodes, including read/write any register ops used in SMPT parse and Infineon (spansion) specific hooks.
The 4B opcodes always take address length of 4 regardless of flash's address mode. In these Infineon chips, 4B opcodes for read/program/ erase are available and 4BAIT advertises them. We don't have to enter 4 byte address mode for read/program/erase.
btw. this is a pity. you are using the stateless 4b opcodes but then you don't provide stateless opcodes for the read any register op :/
Quoted 2 lines
So, I think we need to differentiate between address length for read/program/erase and flash's default address mode.
Or we keep them in sync. E.g. switch to 4bytes mode if we are using the 4 byte. Granted, that sounds like a hack :)
Quoted 2 lines
Obviously we are using
nor->addr_nbytesas address length for read/ program/erase and should keep this usage.Yes, I wasn't aware that we actually two different runtime parameters:
- the read/program/erase address width, also used with the 4b opcodes
- internal mode 3b/4b. Up until now, this wasn't an issue because either the mode was switched or the 4b opcodes were used. So this was mutually exclusive. Now we have flashes which uses 4b opcodes _and_ we need the state of the internal mode.
Quoted 6 lines
I can't think of a good solution for now. Need to think more about this, but I'm pretty busy at the moment. What I think is clear is that we need two different modes here in the
spi_norstruct.nor->addr_nbytesfor the read/program/erase opcodes andnor->address_modeor similar which tracks the SPI flash's internal address mode.
Hi, Takahiro,
Can we determine the flash's internal address mode by querying the flash at run-time? Is this possible on Semper flashes?
To extend the idea, when the flash supports BFPT and defines BFPT_DWORD1_ADDRESS_BYTES_3_ONLY or BFPT_DWORD1_ADDRESS_BYTES_4_ONLY the things are clear, addr_nbytes is fixed.
If the flash does not define BFPT or uses BFPT_DWORD1_ADDRESS_BYTES_3_OR_4, then we could determine the addr mode by querying the flash.
Quoted 7 lines
Quoted 4 lines
For flash's default address mode, my preference is to use
params->addr_nbytes, but I should rename it to something likeparams->def_addr_nbytesand reworkspi_nor_set_addr_nbytes().IMHO params should only be used to store the parsed (or hardcoded) parameters.
yep, I share Michael's opinion.
Cheers,
ta
Quoted 20 lines
-michael
Quoted 17 lines
static int
spi_nor_set_addr_nbytes(struct spi_nor *nor){
if (nor->flags&SNOR_F_HAS_4BAIT) {nor->addr_nbytes= 4;
} else if (nor->params->def_addr_nbytes) {nor->addr_nbytes=nor->params->def_addr_nbytes;Quoted 5 lines
At some point, the mode is switched and
nor->addr_nbytesbecomesparams->addr_nbytes. It seems in your casenor->addr_nbytesshould be 4 right from the beginning. Which also meansnor->addr_nbytesshould be 3 for the other cases (and probably not 0).With
param->def_addr_nbytes, I think we can keepnor->addr_nbytes= 0 during SFDP parse.Thanks,
Takahiro
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
Re: [PATCH v15 6/8] mtd: spi-nor: Retain nor->addr_width at 4BAIT parse
Quoted 96 lines · On 7/22/2022 1:06 AM, [email protected] wrote:
Quoted 88 lines · Michael Walle
EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
Am 2022-05-14 05:51, schrieb Takahiro Kuwano:
Quoted 53 lines · Michael Walle
Quoted 2 lines
[btw the subject still has the old name of the
addr_width]Yes, it must be fixed in next rev.
Quoted 31 lines
Am 2022-05-13 03:26, schrieb Takahiro Kuwano:
Quoted 22 lines · Michael Walle
Quoted 13 lines
Am 2022-05-10 00:10, schrieb [email protected]:
Quoted 5 lines
From: Takahiro Kuwano <[email protected]>
In 4BAIT parse, keep
nor->params->addr_widthbecause it may be used as
current address mode in SMPT parse later on.Mh I'm not sure this is needed at all.
SFDP spec says
Variable address length (the current setting of the address length mode defines the address length)Quoted 8 lines
and
When the length is defined as variable, the software or hardware controlling the memory is aware of the address length mode last set in the memory device and this same length of address.We don't set any address mode until all the SFDP parsing is over. Therefore we should always be in 3 byte mode, no?
Quoted 7 lines
Actually there are some devices that have variable address length but 4 byte mode by default (I will work on those devices after this series
is settled). To support such case, I prefer to useparams->addr_nbytes
as current address mode so that I can fix it inpost_bfpt_fixup()hook.Quoted 1 line
Are there public datasheets available? So these devices have a 3 byte
I will send datasheets to you in another email. At this point, only summary datasheet is available in website.
Quoted 1 line
and a 4 byte mode, but after reset, they are in the 4 byte mode? Looks
Yes.
Quoted 3 lines
like it should be fixed in a different way. I'm not sure the "current mode" handling is correct.
Yes, we may want to introduce a new flag like
SPI_NOR_4BAM_DEFAULTand check
the flag in BFPT parse. Once I send another series, please review.Quoted 3 lines
We need to differentiate between the mode the flash currently is using (
nor->addr_nbytes) and the mode parsed by SFDP (params->addr_nbytes).Quoted 8 lines
The flash's address mode affects the address length of Non-4B opcodes, including read/write any register ops used in SMPT parse and Infineon (spansion) specific hooks.
The 4B opcodes always take address length of 4 regardless of flash's address mode. In these Infineon chips, 4B opcodes for read/program/ erase are available and 4BAIT advertises them. We don't have to enter 4 byte address mode for read/program/erase.
btw. this is a pity. you are using the stateless 4b opcodes but then you don't provide stateless opcodes for the read any register op :/
Quoted 2 lines
So, I think we need to differentiate between address length for read/program/erase and flash's default address mode.
Or we keep them in sync. E.g. switch to 4bytes mode if we are using the 4 byte. Granted, that sounds like a hack :)
Quoted 2 lines
Obviously we are using
nor->addr_nbytesas address length for read/ program/erase and should keep this usage.Yes, I wasn't aware that we actually two different runtime parameters:
- the read/program/erase address width, also used with the 4b opcodes
- internal mode 3b/4b. Up until now, this wasn't an issue because either the mode was switched or the 4b opcodes were used. So this was mutually exclusive. Now we have flashes which uses 4b opcodes _and_ we need the state of the internal mode.Quoted 6 lines
I can't think of a good solution for now. Need to think more about this, but I'm pretty busy at the moment. What I think is clear is that we need two different modes here in the
spi_norstruct.nor->addr_nbytesfor the read/program/erase opcodes andnor->address_modeor similar which tracks the SPI flash's internal address mode.
Quoted 5 lines
Hi, Takahiro,
Can we determine the flash's internal address mode by querying the flash at run-time? Is this possible on Semper flashes?
CFR2V[7] has current address mode, but to read that, we need to issue Read Any Register which address length relies on current address mode. Chicken-and-egg...
Quoted 12 lines
To extend the idea, when the flash supports BFPT and defines
BFPT_DWORD1_ADDRESS_BYTES_3_ONLYorBFPT_DWORD1_ADDRESS_BYTES_4_ONLYthe things are clear,addr_nbytesis fixed.
If the flash does not define BFPT or usesBFPT_DWORD1_ADDRESS_BYTES_3_OR_4, then we could determine the addr mode by querying the flash.Quoted 5 lines
Quoted 4 lines
For flash's default address mode, my preference is to use
params->addr_nbytes, but I should rename it to something likeparams->def_addr_nbytesand reworkspi_nor_set_addr_nbytes().
Quoted 29 lines
Quoted 2 lines
IMHO params should only be used to store the parsed (or hardcoded) parameters.
yep, I share Michael's opinion.
Cheers,
taQuoted 20 lines
-michael
Quoted 17 lines
static int
spi_nor_set_addr_nbytes(struct spi_nor *nor){
if (nor->flags&SNOR_F_HAS_4BAIT) {nor->addr_nbytes= 4;
} else if (nor->params->def_addr_nbytes) {nor->addr_nbytes=nor->params->def_addr_nbytes;Quoted 5 lines
At some point, the mode is switched and
nor->addr_nbytesbecomesparams->addr_nbytes. It seems in your casenor->addr_nbytesshould be 4 right from the beginning. Which also meansnor->addr_nbytesshould be 3 for the other cases (and probably not 0).With
param->def_addr_nbytes, I think we can keepnor->addr_nbytes= 0 during SFDP parse.Thanks,
Takahiro
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
Re: [PATCH v15 6/8] mtd: spi-nor: Retain nor->addr_width at 4BAIT parse
On 7/22/22 07:00, Takahiro Kuwano wrote:
Good morning, Takahiro!
Quoted 99 lines
EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
Quoted 96 lines · On 7/22/2022 1:06 AM, [email protected] wrote:
Quoted 94 lines · Michael Walle
EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
Am 2022-05-14 05:51, schrieb Takahiro Kuwano:
Quoted 53 lines · Michael Walle
Quoted 2 lines
[btw the subject still has the old name of the
addr_width]Yes, it must be fixed in next rev.
Quoted 31 lines
Am 2022-05-13 03:26, schrieb Takahiro Kuwano:
Quoted 22 lines · Michael Walle
Quoted 13 lines
Am 2022-05-10 00:10, schrieb [email protected]:
Quoted 5 lines
From: Takahiro Kuwano <[email protected]>
In 4BAIT parse, keep
nor->params->addr_widthbecause it may be used as
current address mode in SMPT parse later on.Mh I'm not sure this is needed at all.
SFDP spec says
Variable address length (the current setting of the address length mode defines the address length)Quoted 8 lines
and
When the length is defined as variable, the software or hardware controlling the memory is aware of the address length mode last set in the memory device and this same length of address.We don't set any address mode until all the SFDP parsing is over. Therefore we should always be in 3 byte mode, no?
Quoted 7 lines
Actually there are some devices that have variable address length but 4 byte mode by default (I will work on those devices after this series
is settled). To support such case, I prefer to useparams->addr_nbytes
as current address mode so that I can fix it inpost_bfpt_fixup()hook.Quoted 1 line
Are there public datasheets available? So these devices have a 3 byte
I will send datasheets to you in another email. At this point, only summary datasheet is available in website.
Quoted 1 line
and a 4 byte mode, but after reset, they are in the 4 byte mode? Looks
Yes.
Quoted 3 lines
like it should be fixed in a different way. I'm not sure the "current mode" handling is correct.
Yes, we may want to introduce a new flag like
SPI_NOR_4BAM_DEFAULTand check
the flag in BFPT parse. Once I send another series, please review.Quoted 3 lines
We need to differentiate between the mode the flash currently is using (
nor->addr_nbytes) and the mode parsed by SFDP (params->addr_nbytes).Quoted 8 lines
The flash's address mode affects the address length of Non-4B opcodes, including read/write any register ops used in SMPT parse and Infineon (spansion) specific hooks.
The 4B opcodes always take address length of 4 regardless of flash's address mode. In these Infineon chips, 4B opcodes for read/program/ erase are available and 4BAIT advertises them. We don't have to enter 4 byte address mode for read/program/erase.
btw. this is a pity. you are using the stateless 4b opcodes but then you don't provide stateless opcodes for the read any register op :/
Quoted 2 lines
So, I think we need to differentiate between address length for read/program/erase and flash's default address mode.
Or we keep them in sync. E.g. switch to 4bytes mode if we are using the 4 byte. Granted, that sounds like a hack :)
Quoted 2 lines
Obviously we are using
nor->addr_nbytesas address length for read/ program/erase and should keep this usage.Yes, I wasn't aware that we actually two different runtime parameters:
- the read/program/erase address width, also used with the 4b opcodes
- internal mode 3b/4b. Up until now, this wasn't an issue because either the mode was switched or the 4b opcodes were used. So this was mutually exclusive. Now we have flashes which uses 4b opcodes _and_ we need the state of the internal mode.I can't think of a good solution for now. Need to think more about this, but I'm pretty busy at the moment. What I think is clear is that we need two different modes here in the
spi_norstruct.nor->addr_nbytesfor the read/program/erase opcodes andnor->address_modeor similar which tracks the SPI flash's internal address mode.
Quoted 9 lines
Quoted 5 lines
Hi, Takahiro,
Can we determine the flash's internal address mode by querying the flash at run-time? Is this possible on Semper flashes?
CFR2V[7] has current address mode, but to read that, we need to issue Read Any Register which address length relies on current address mode. Chicken-and-egg...
I see. What happens if we issue the Read Any Register command with the wrong address internal mode? Will I read just 0xff? For example try reading CFR2V[7] using addr_nbytes of value 3, and if it fails, to read it again but this time using addr_nbytes of value 4.
Cheers,
ta
Quoted 35 lines
Quoted 35 lines
To extend the idea, when the flash supports BFPT and defines
BFPT_DWORD1_ADDRESS_BYTES_3_ONLYorBFPT_DWORD1_ADDRESS_BYTES_4_ONLYthe things are clear,addr_nbytesis fixed.
If the flash does not define BFPT or usesBFPT_DWORD1_ADDRESS_BYTES_3_OR_4, then we could determine the addr mode by querying the flash.Quoted 7 lines
Quoted 4 lines
For flash's default address mode, my preference is to use
params->addr_nbytes, but I should rename it to something likeparams->def_addr_nbytesand reworkspi_nor_set_addr_nbytes().IMHO params should only be used to store the parsed (or hardcoded) parameters.
yep, I share Michael's opinion.
Cheers,
taQuoted 15 lines
-michael
Quoted 12 lines
static int
spi_nor_set_addr_nbytes(struct spi_nor *nor){ if (nor->flags & SNOR_F_HAS_4BAIT) { nor->addr_nbytes = 4; } else if (nor->params->def_addr_nbytes) { nor->addr_nbytes = nor->params->def_addr_nbytes;Quoted 5 lines
At some point, the mode is switched and
nor->addr_nbytesbecomesparams->addr_nbytes. It seems in your casenor->addr_nbytesshould be 4 right from the beginning. Which also meansnor->addr_nbytesshould be 3 for the other cases (and probably not 0).
Quoted 6 lines
Quoted 6 lines
Quoted 5 lines
Quoted 5 lines
With
param->def_addr_nbytes, I think we can keepnor->addr_nbytes= 0 during SFDP parse.Thanks,
Takahiro
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
Re: [PATCH v15 6/8] mtd: spi-nor: Retain nor->addr_width at 4BAIT parse
I have repeatedly told you to stop contacting this email.
Quoted 163 lines · On Jul 22, 2022, at 12:23 AM, [email protected] wrote:
On 7/22/22 07:00, Takahiro Kuwano wrote:
Good morning, Takahiro!
Quoted 99 lines
EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
Quoted 97 lines · On 7/22/2022 1:06 AM, [email protected] wrote:
Quoted 94 lines · Michael Walle
EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
Am 2022-05-14 05:51, schrieb Takahiro Kuwano:
Quoted 53 lines · Michael Walle
Quoted 2 lines
[btw the subject still has the old name of the
addr_width]Yes, it must be fixed in next rev.
Quoted 31 lines
Am 2022-05-13 03:26, schrieb Takahiro Kuwano:
Quoted 22 lines · Michael Walle
Quoted 13 lines
Am 2022-05-10 00:10, schrieb [email protected]:
Quoted 5 lines
From: Takahiro Kuwano <[email protected]>
In 4BAIT parse, keep
nor->params->addr_widthbecause it may be used as
current address mode in SMPT parse later on.Mh I'm not sure this is needed at all.
SFDP spec says
Variable address length (the current setting of the address length mode defines the address length)Quoted 8 lines
and
When the length is defined as variable, the software or hardware controlling the memory is aware of the address length mode last set in the memory device and this same length of address.We don't set any address mode until all the SFDP parsing is over. Therefore we should always be in 3 byte mode, no?
Quoted 7 lines
Actually there are some devices that have variable address length but 4 byte mode by default (I will work on those devices after this series
is settled). To support such case, I prefer to useparams->addr_nbytes
as current address mode so that I can fix it inpost_bfpt_fixup()hook.Quoted 1 line
Are there public datasheets available? So these devices have a 3 byte
I will send datasheets to you in another email. At this point, only summary datasheet is available in website.
Quoted 1 line
and a 4 byte mode, but after reset, they are in the 4 byte mode? Looks
Yes.
Quoted 3 lines
like it should be fixed in a different way. I'm not sure the "current mode" handling is correct.
Yes, we may want to introduce a new flag like
SPI_NOR_4BAM_DEFAULTand check
the flag in BFPT parse. Once I send another series, please review.Quoted 3 lines
We need to differentiate between the mode the flash currently is using (
nor->addr_nbytes) and the mode parsed by SFDP (params->addr_nbytes).Quoted 8 lines
The flash's address mode affects the address length of Non-4B opcodes, including read/write any register ops used in SMPT parse and Infineon (spansion) specific hooks.
The 4B opcodes always take address length of 4 regardless of flash's address mode. In these Infineon chips, 4B opcodes for read/program/ erase are available and 4BAIT advertises them. We don't have to enter 4 byte address mode for read/program/erase.
btw. this is a pity. you are using the stateless 4b opcodes but then you don't provide stateless opcodes for the read any register op :/
Quoted 2 lines
So, I think we need to differentiate between address length for read/program/erase and flash's default address mode.
Or we keep them in sync. E.g. switch to 4bytes mode if we are using the 4 byte. Granted, that sounds like a hack :)
Quoted 2 lines
Obviously we are using
nor->addr_nbytesas address length for read/ program/erase and should keep this usage.Yes, I wasn't aware that we actually two different runtime parameters:
- the read/program/erase address width, also used with the 4b opcodes
- internal mode 3b/4b. Up until now, this wasn't an issue because either the mode was switched or the 4b opcodes were used. So this was mutually exclusive. Now we have flashes which uses 4b opcodes _and_ we need the state of the internal mode.I can't think of a good solution for now. Need to think more about this, but I'm pretty busy at the moment. What I think is clear is that we need two different modes here in the
spi_norstruct.nor->addr_nbytesfor the read/program/erase opcodes andnor->address_modeor similar which tracks the SPI flash's internal address mode.Quoted 9 lines
Quoted 5 lines
Hi, Takahiro,
Can we determine the flash's internal address mode by querying the flash at run-time? Is this possible on Semper flashes?
CFR2V[7] has current address mode, but to read that, we need to issue Read Any Register which address length relies on current address mode. Chicken-and-egg...
I see. What happens if we issue the Read Any Register command with the wrong address internal mode? Will I read just
0xff? For example try reading CFR2V[7] usingaddr_nbytesof value 3, and if it fails, to read it again but this time usingaddr_nbytesof value 4.Cheers,
taQuoted 38 lines
Quoted 38 lines
To extend the idea, when the flash supports BFPT and defines
BFPT_DWORD1_ADDRESS_BYTES_3_ONLYorBFPT_DWORD1_ADDRESS_BYTES_4_ONLYthe things are clear,addr_nbytesis fixed.
If the flash does not define BFPT or usesBFPT_DWORD1_ADDRESS_BYTES_3_OR_4, then we could determine the addr mode by querying the flash.Quoted 7 lines
Quoted 4 lines
For flash's default address mode, my preference is to use
params->addr_nbytes, but I should rename it to something likeparams->def_addr_nbytesand reworkspi_nor_set_addr_nbytes().IMHO params should only be used to store the parsed (or hardcoded) parameters.
yep, I share Michael's opinion.
Cheers,
taQuoted 18 lines
-michael
Quoted 15 lines
static int
spi_nor_set_addr_nbytes(struct spi_nor *nor){ if (nor->flags & SNOR_F_HAS_4BAIT) { nor->addr_nbytes = 4; } else if (nor->params->def_addr_nbytes) { nor->addr_nbytes = nor->params->def_addr_nbytes;Quoted 5 lines
At some point, the mode is switched and
nor->addr_nbytesbecomesparams->addr_nbytes. It seems in your casenor->addr_nbytesshould be 4 right from the beginning. Which also meansnor->addr_nbytesshould be 3 for the other cases (and probably not 0).With
param->def_addr_nbytes, I think we can keepnor->addr_nbytes= 0 during SFDP parse.
Quoted 7 lines
Quoted 3 lines
Quoted 3 lines
Quoted 2 lines
Quoted 2 lines
Thanks,
Takahiro______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
Re: [PATCH v15 6/8] mtd: spi-nor: Retain nor->addr_width at 4BAIT parse
In reply to [email protected]Quoted 4 lines · On 7/22/2022 1:20 PM, [email protected] wrote:
On 7/22/22 07:00, Takahiro Kuwano wrote:
Good morning, Takahiro!
Good morning, Tudor!
Quoted 109 lines
Quoted 99 lines
EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
Quoted 96 lines · On 7/22/2022 1:06 AM, [email protected] wrote:
Quoted 94 lines · Michael Walle
EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
Am 2022-05-14 05:51, schrieb Takahiro Kuwano:
Quoted 53 lines · Michael Walle
Quoted 2 lines
[btw the subject still has the old name of the
addr_width]Yes, it must be fixed in next rev.
Quoted 31 lines
Am 2022-05-13 03:26, schrieb Takahiro Kuwano:
Quoted 22 lines · Michael Walle
Quoted 13 lines
Am 2022-05-10 00:10, schrieb [email protected]:
Quoted 5 lines
From: Takahiro Kuwano <[email protected]>
In 4BAIT parse, keep
nor->params->addr_widthbecause it may be used as
current address mode in SMPT parse later on.Mh I'm not sure this is needed at all.
SFDP spec says
Variable address length (the current setting of the address length mode defines the address length)Quoted 8 lines
and
When the length is defined as variable, the software or hardware controlling the memory is aware of the address length mode last set in the memory device and this same length of address.We don't set any address mode until all the SFDP parsing is over. Therefore we should always be in 3 byte mode, no?
Quoted 7 lines
Actually there are some devices that have variable address length but 4 byte mode by default (I will work on those devices after this series
is settled). To support such case, I prefer to useparams->addr_nbytes
as current address mode so that I can fix it inpost_bfpt_fixup()hook.Quoted 1 line
Are there public datasheets available? So these devices have a 3 byte
I will send datasheets to you in another email. At this point, only summary datasheet is available in website.
Quoted 1 line
and a 4 byte mode, but after reset, they are in the 4 byte mode? Looks
Yes.
Quoted 3 lines
like it should be fixed in a different way. I'm not sure the "current mode" handling is correct.
Yes, we may want to introduce a new flag like
SPI_NOR_4BAM_DEFAULTand check
the flag in BFPT parse. Once I send another series, please review.Quoted 3 lines
We need to differentiate between the mode the flash currently is using (
nor->addr_nbytes) and the mode parsed by SFDP (params->addr_nbytes).Quoted 8 lines
The flash's address mode affects the address length of Non-4B opcodes, including read/write any register ops used in SMPT parse and Infineon (spansion) specific hooks.
The 4B opcodes always take address length of 4 regardless of flash's address mode. In these Infineon chips, 4B opcodes for read/program/ erase are available and 4BAIT advertises them. We don't have to enter 4 byte address mode for read/program/erase.
btw. this is a pity. you are using the stateless 4b opcodes but then you don't provide stateless opcodes for the read any register op :/
Quoted 2 lines
So, I think we need to differentiate between address length for read/program/erase and flash's default address mode.
Or we keep them in sync. E.g. switch to 4bytes mode if we are using the 4 byte. Granted, that sounds like a hack :)
Quoted 2 lines
Obviously we are using
nor->addr_nbytesas address length for read/ program/erase and should keep this usage.Yes, I wasn't aware that we actually two different runtime parameters:
- the read/program/erase address width, also used with the 4b opcodes
- internal mode 3b/4b. Up until now, this wasn't an issue because either the mode was switched or the 4b opcodes were used. So this was mutually exclusive. Now we have flashes which uses 4b opcodes _and_ we need the state of the internal mode.I can't think of a good solution for now. Need to think more about this, but I'm pretty busy at the moment. What I think is clear is that we need two different modes here in the
spi_norstruct.nor->addr_nbytesfor the read/program/erase opcodes andnor->address_modeor similar which tracks the SPI flash's internal address mode.Quoted 9 lines
Quoted 5 lines
Hi, Takahiro,
Can we determine the flash's internal address mode by querying the flash at run-time? Is this possible on Semper flashes?
CFR2V[7] has current address mode, but to read that, we need to issue Read Any Register which address length relies on current address mode. Chicken-and-egg...
Quoted 6 lines
I see. What happens if we issue the Read Any Register command with the wrong address internal mode? Will I read just
0xff? For example try reading CFR2V[7] usingaddr_nbytesof value 3, and if it fails, to read it again but this time usingaddr_nbytesof value 4.
It's undetermined. In case we issue Read Any Register with 3B address, the host controller outputs 4 bytes (opcode + address) then inputs 1 byte. If the device is in 4B address mode at this time, the host controller inputs the 1 byte while device is still waits for LSB of address so IO is not driven by device.
Thanks,
Takahiro
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
Re: [PATCH v15 6/8] mtd: spi-nor: Retain nor->addr_width at 4BAIT parse
Quoted 124 lines · Takahiro Kuwano
EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
Quoted 4 lines · On 7/22/2022 1:20 PM, [email protected] wrote:
On 7/22/22 07:00, Takahiro Kuwano wrote:
Good morning, Takahiro!
Good morning, Tudor!
Quoted 109 lines
Quoted 99 lines
EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
Quoted 96 lines · On 7/22/2022 1:06 AM, [email protected] wrote:
Quoted 94 lines · Michael Walle
EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
Am 2022-05-14 05:51, schrieb Takahiro Kuwano:
Quoted 53 lines · Michael Walle
Quoted 2 lines
[btw the subject still has the old name of the
addr_width]Yes, it must be fixed in next rev.
Quoted 31 lines
Am 2022-05-13 03:26, schrieb Takahiro Kuwano:
Quoted 22 lines · Michael Walle
Quoted 13 lines
Am 2022-05-10 00:10, schrieb [email protected]:
Quoted 5 lines
From: Takahiro Kuwano <[email protected]>
In 4BAIT parse, keep
nor->params->addr_widthbecause it may be used as
current address mode in SMPT parse later on.Mh I'm not sure this is needed at all.
SFDP spec says
Variable address length (the current setting of the address length mode defines the address length)Quoted 8 lines
and
When the length is defined as variable, the software or hardware controlling the memory is aware of the address length mode last set in the memory device and this same length of address.We don't set any address mode until all the SFDP parsing is over. Therefore we should always be in 3 byte mode, no?
Quoted 7 lines
Actually there are some devices that have variable address length but 4 byte mode by default (I will work on those devices after this series
is settled). To support such case, I prefer to useparams->addr_nbytes
as current address mode so that I can fix it inpost_bfpt_fixup()hook.Quoted 1 line
Are there public datasheets available? So these devices have a 3 byte
I will send datasheets to you in another email. At this point, only summary datasheet is available in website.
Quoted 1 line
and a 4 byte mode, but after reset, they are in the 4 byte mode? Looks
Yes.
Quoted 3 lines
like it should be fixed in a different way. I'm not sure the "current mode" handling is correct.
Yes, we may want to introduce a new flag like
SPI_NOR_4BAM_DEFAULTand check
the flag in BFPT parse. Once I send another series, please review.Quoted 3 lines
We need to differentiate between the mode the flash currently is using (
nor->addr_nbytes) and the mode parsed by SFDP (params->addr_nbytes).Quoted 8 lines
The flash's address mode affects the address length of Non-4B opcodes, including read/write any register ops used in SMPT parse and Infineon (spansion) specific hooks.
The 4B opcodes always take address length of 4 regardless of flash's address mode. In these Infineon chips, 4B opcodes for read/program/ erase are available and 4BAIT advertises them. We don't have to enter 4 byte address mode for read/program/erase.
btw. this is a pity. you are using the stateless 4b opcodes but then you don't provide stateless opcodes for the read any register op :/
Quoted 2 lines
So, I think we need to differentiate between address length for read/program/erase and flash's default address mode.
Or we keep them in sync. E.g. switch to 4bytes mode if we are using the 4 byte. Granted, that sounds like a hack :)
Quoted 2 lines
Obviously we are using
nor->addr_nbytesas address length for read/ program/erase and should keep this usage.Yes, I wasn't aware that we actually two different runtime parameters:
- the read/program/erase address width, also used with the 4b opcodes
- internal mode 3b/4b. Up until now, this wasn't an issue because either the mode was switched or the 4b opcodes were used. So this was mutually exclusive. Now we have flashes which uses 4b opcodes _and_ we need the state of the internal mode.I can't think of a good solution for now. Need to think more about this, but I'm pretty busy at the moment. What I think is clear is that we need two different modes here in the
spi_norstruct.nor->addr_nbytesfor the read/program/erase opcodes andnor->address_modeor similar which tracks the SPI flash's internal address mode.Quoted 9 lines
Quoted 5 lines
Hi, Takahiro,
Can we determine the flash's internal address mode by querying the flash at run-time? Is this possible on Semper flashes?
CFR2V[7] has current address mode, but to read that, we need to issue Read Any Register which address length relies on current address mode. Chicken-and-egg...
Quoted 6 lines
I see. What happens if we issue the Read Any Register command with the wrong address internal mode? Will I read just
0xff? For example try reading CFR2V[7] usingaddr_nbytesof value 3, and if it fails, to read it again but this time usingaddr_nbytesof value 4.
Quoted 6 lines
It's undetermined. In case we issue Read Any Register with 3B address, the host controller outputs 4 bytes (opcode + address) then inputs 1 byte. If the device is in 4B address mode at this time, the host controller inputs the 1 byte while device is still waits for LSB of address so IO is not driven by device.
So if the IO lines are floating, we'll "read" whatever is indicated by the IOs at that specific moment of time, right?
If so, we're forced to statically specify the default internal address mode.
Signature · 5 lines
Cheers, ta ______________________________________________________ Linux MTD discussion mailing list http://lists.infradead.org/mailman/listinfo/linux-mtd/
Re: [PATCH v15 6/8] mtd: spi-nor: Retain nor->addr_width at 4BAIT parse
Quoted 132 lines · On 7/22/2022 2:06 PM, [email protected] wrote:
Quoted 124 lines · Takahiro Kuwano
EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
Quoted 4 lines · On 7/22/2022 1:20 PM, [email protected] wrote:
On 7/22/22 07:00, Takahiro Kuwano wrote:
Good morning, Takahiro!
Good morning, Tudor!
Quoted 109 lines
Quoted 99 lines
EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
Quoted 96 lines · On 7/22/2022 1:06 AM, [email protected] wrote:
Quoted 94 lines · Michael Walle
EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
Am 2022-05-14 05:51, schrieb Takahiro Kuwano:
Quoted 53 lines · Michael Walle
Quoted 2 lines
[btw the subject still has the old name of the
addr_width]Yes, it must be fixed in next rev.
Quoted 31 lines
Am 2022-05-13 03:26, schrieb Takahiro Kuwano:
Quoted 22 lines · Michael Walle
Quoted 13 lines
Am 2022-05-10 00:10, schrieb [email protected]:
Quoted 5 lines
From: Takahiro Kuwano <[email protected]>
In 4BAIT parse, keep
nor->params->addr_widthbecause it may be used as
current address mode in SMPT parse later on.Mh I'm not sure this is needed at all.
SFDP spec says
Variable address length (the current setting of the address length mode defines the address length)Quoted 8 lines
and
When the length is defined as variable, the software or hardware controlling the memory is aware of the address length mode last set in the memory device and this same length of address.We don't set any address mode until all the SFDP parsing is over. Therefore we should always be in 3 byte mode, no?
Quoted 7 lines
Actually there are some devices that have variable address length but 4 byte mode by default (I will work on those devices after this series
is settled). To support such case, I prefer to useparams->addr_nbytes
as current address mode so that I can fix it inpost_bfpt_fixup()hook.Quoted 1 line
Are there public datasheets available? So these devices have a 3 byte
I will send datasheets to you in another email. At this point, only summary datasheet is available in website.
Quoted 1 line
and a 4 byte mode, but after reset, they are in the 4 byte mode? Looks
Yes.
Quoted 3 lines
like it should be fixed in a different way. I'm not sure the "current mode" handling is correct.
Yes, we may want to introduce a new flag like
SPI_NOR_4BAM_DEFAULTand check
the flag in BFPT parse. Once I send another series, please review.Quoted 3 lines
We need to differentiate between the mode the flash currently is using (
nor->addr_nbytes) and the mode parsed by SFDP (params->addr_nbytes).Quoted 8 lines
The flash's address mode affects the address length of Non-4B opcodes, including read/write any register ops used in SMPT parse and Infineon (spansion) specific hooks.
The 4B opcodes always take address length of 4 regardless of flash's address mode. In these Infineon chips, 4B opcodes for read/program/ erase are available and 4BAIT advertises them. We don't have to enter 4 byte address mode for read/program/erase.
btw. this is a pity. you are using the stateless 4b opcodes but then you don't provide stateless opcodes for the read any register op :/
Quoted 2 lines
So, I think we need to differentiate between address length for read/program/erase and flash's default address mode.
Or we keep them in sync. E.g. switch to 4bytes mode if we are using the 4 byte. Granted, that sounds like a hack :)
Quoted 2 lines
Obviously we are using
nor->addr_nbytesas address length for read/ program/erase and should keep this usage.Yes, I wasn't aware that we actually two different runtime parameters:
- the read/program/erase address width, also used with the 4b opcodes
- internal mode 3b/4b. Up until now, this wasn't an issue because either the mode was switched or the 4b opcodes were used. So this was mutually exclusive. Now we have flashes which uses 4b opcodes _and_ we need the state of the internal mode.I can't think of a good solution for now. Need to think more about this, but I'm pretty busy at the moment. What I think is clear is that we need two different modes here in the
spi_norstruct.nor->addr_nbytesfor the read/program/erase opcodes andnor->address_modeor similar which tracks the SPI flash's internal address mode.Quoted 9 lines
Quoted 5 lines
Hi, Takahiro,
Can we determine the flash's internal address mode by querying the flash at run-time? Is this possible on Semper flashes?
CFR2V[7] has current address mode, but to read that, we need to issue Read Any Register which address length relies on current address mode. Chicken-and-egg...
Quoted 6 lines
I see. What happens if we issue the Read Any Register command with the wrong address internal mode? Will I read just
0xff? For example try reading CFR2V[7] usingaddr_nbytesof value 3, and if it fails, to read it again but this time usingaddr_nbytesof value 4.Quoted 6 lines
It's undetermined. In case we issue Read Any Register with 3B address, the host controller outputs 4 bytes (opcode + address) then inputs 1 byte. If the device is in 4B address mode at this time, the host controller inputs the 1 byte while device is still waits for LSB of address so IO is not driven by device.
Quoted 3 lines
So if the IO lines are floating, we'll "read" whatever is indicated by the IOs at that specific moment of time, right?
Yes, right.
Quoted 3 lines
If so, we're forced to statically specify the default internal address mode.
Yes.
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
Re: [PATCH v15 6/8] mtd: spi-nor: Retain nor->addr_width at 4BAIT parse
Quoted 138 lines · Takahiro Kuwano
EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
Quoted 132 lines · On 7/22/2022 2:06 PM, [email protected] wrote:
Quoted 124 lines · Takahiro Kuwano
EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
Quoted 4 lines · On 7/22/2022 1:20 PM, [email protected] wrote:
On 7/22/22 07:00, Takahiro Kuwano wrote:
Good morning, Takahiro!
Good morning, Tudor!
Quoted 109 lines
Quoted 99 lines
EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
Quoted 96 lines · On 7/22/2022 1:06 AM, [email protected] wrote:
Quoted 94 lines · Michael Walle
EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
Am 2022-05-14 05:51, schrieb Takahiro Kuwano:
Quoted 53 lines · Michael Walle
Quoted 2 lines
[btw the subject still has the old name of the
addr_width]Yes, it must be fixed in next rev.
Quoted 31 lines
Am 2022-05-13 03:26, schrieb Takahiro Kuwano:
Quoted 22 lines · Michael Walle
Quoted 13 lines
Am 2022-05-10 00:10, schrieb [email protected]:
Quoted 5 lines
From: Takahiro Kuwano <[email protected]>
In 4BAIT parse, keep
nor->params->addr_widthbecause it may be used as
current address mode in SMPT parse later on.Mh I'm not sure this is needed at all.
SFDP spec says
Variable address length (the current setting of the address length mode defines the address length)Quoted 8 lines
and
When the length is defined as variable, the software or hardware controlling the memory is aware of the address length mode last set in the memory device and this same length of address.We don't set any address mode until all the SFDP parsing is over. Therefore we should always be in 3 byte mode, no?
Quoted 7 lines
Actually there are some devices that have variable address length but 4 byte mode by default (I will work on those devices after this series
is settled). To support such case, I prefer to useparams->addr_nbytes
as current address mode so that I can fix it inpost_bfpt_fixup()hook.Quoted 1 line
Are there public datasheets available? So these devices have a 3 byte
I will send datasheets to you in another email. At this point, only summary datasheet is available in website.
Quoted 1 line
and a 4 byte mode, but after reset, they are in the 4 byte mode? Looks
Yes.
Quoted 3 lines
like it should be fixed in a different way. I'm not sure the "current mode" handling is correct.
Yes, we may want to introduce a new flag like
SPI_NOR_4BAM_DEFAULTand check
the flag in BFPT parse. Once I send another series, please review.Quoted 3 lines
We need to differentiate between the mode the flash currently is using (
nor->addr_nbytes) and the mode parsed by SFDP (params->addr_nbytes).Quoted 8 lines
The flash's address mode affects the address length of Non-4B opcodes, including read/write any register ops used in SMPT parse and Infineon (spansion) specific hooks.
The 4B opcodes always take address length of 4 regardless of flash's address mode. In these Infineon chips, 4B opcodes for read/program/ erase are available and 4BAIT advertises them. We don't have to enter 4 byte address mode for read/program/erase.
btw. this is a pity. you are using the stateless 4b opcodes but then you don't provide stateless opcodes for the read any register op :/
Quoted 2 lines
So, I think we need to differentiate between address length for read/program/erase and flash's default address mode.
Or we keep them in sync. E.g. switch to 4bytes mode if we are using the 4 byte. Granted, that sounds like a hack :)
Quoted 2 lines
Obviously we are using
nor->addr_nbytesas address length for read/ program/erase and should keep this usage.Yes, I wasn't aware that we actually two different runtime parameters:
- the read/program/erase address width, also used with the 4b opcodes
- internal mode 3b/4b. Up until now, this wasn't an issue because either the mode was switched or the 4b opcodes were used. So this was mutually exclusive. Now we have flashes which uses 4b opcodes _and_ we need the state of the internal mode.I can't think of a good solution for now. Need to think more about this, but I'm pretty busy at the moment. What I think is clear is that we need two different modes here in the
spi_norstruct.nor->addr_nbytesfor the read/program/erase opcodes andnor->address_modeor similar which tracks the SPI flash's internal address mode.Quoted 9 lines
Quoted 5 lines
Hi, Takahiro,
Can we determine the flash's internal address mode by querying the flash at run-time? Is this possible on Semper flashes?
CFR2V[7] has current address mode, but to read that, we need to issue Read Any Register which address length relies on current address mode. Chicken-and-egg...
Quoted 6 lines
I see. What happens if we issue the Read Any Register command with the wrong address internal mode? Will I read just
0xff? For example try reading CFR2V[7] usingaddr_nbytesof value 3, and if it fails, to read it again but this time usingaddr_nbytesof value 4.Quoted 6 lines
It's undetermined. In case we issue Read Any Register with 3B address, the host controller outputs 4 bytes (opcode + address) then inputs 1 byte. If the device is in 4B address mode at this time, the host controller inputs the 1 byte while device is still waits for LSB of address so IO is not driven by device.
Quoted 3 lines
So if the IO lines are floating, we'll "read" whatever is indicated by the IOs at that specific moment of time, right?
Quoted 6 lines
Yes, right.
Quoted 3 lines
If so, we're forced to statically specify the default internal address mode.
Yes.
OK, let me scratch something.
Signature · 5 lines
Cheers, ta ______________________________________________________ Linux MTD discussion mailing list http://lists.infradead.org/mailman/listinfo/linux-mtd/
Re: [PATCH v15 6/8] mtd: spi-nor: Retain nor->addr_width at 4BAIT parse
Quoted 141 lines · On 7/22/22 09:08, [email protected] wrote:
EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
Quoted 138 lines · Takahiro Kuwano
EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
Quoted 135 lines · On 7/22/2022 2:06 PM, [email protected] wrote:
Quoted 124 lines · Takahiro Kuwano
EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
Quoted 4 lines · On 7/22/2022 1:20 PM, [email protected] wrote:
On 7/22/22 07:00, Takahiro Kuwano wrote:
Good morning, Takahiro!
Good morning, Tudor!
Quoted 109 lines
Quoted 99 lines
EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
Quoted 96 lines · On 7/22/2022 1:06 AM, [email protected] wrote:
Quoted 94 lines · Michael Walle
EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
Am 2022-05-14 05:51, schrieb Takahiro Kuwano:
Quoted 53 lines · Michael Walle
Quoted 2 lines
[btw the subject still has the old name of the
addr_width]Yes, it must be fixed in next rev.
Quoted 31 lines
Am 2022-05-13 03:26, schrieb Takahiro Kuwano:
Quoted 22 lines · Michael Walle
Quoted 13 lines
Am 2022-05-10 00:10, schrieb [email protected]:
Quoted 5 lines
From: Takahiro Kuwano <[email protected]>
In 4BAIT parse, keep nor->params->addr_width because it may be used
as
current address mode in SMPT parse later on.Mh I'm not sure this is needed at all.
SFDP spec says
Variable address length (the current setting of the address length mode defines the address length)Quoted 8 lines
and
When the length is defined as variable, the software or hardware controlling the memory is aware of the address length mode last set in the memory device and this same length of address.We don't set any address mode until all the SFDP parsing is over. Therefore we should always be in 3 byte mode, no?
Quoted 7 lines
Actually there are some devices that have variable address length but 4 byte mode by default (I will work on those devices after this series
is settled). To support such case, I prefer to useparams->addr_nbytes
as current address mode so that I can fix it inpost_bfpt_fixup()hook.Quoted 1 line
Are there public datasheets available? So these devices have a 3 byte
I will send datasheets to you in another email. At this point, only summary datasheet is available in website.
Quoted 1 line
and a 4 byte mode, but after reset, they are in the 4 byte mode? Looks
Yes.
Quoted 3 lines
like it should be fixed in a different way. I'm not sure the "current mode" handling is correct.
Yes, we may want to introduce a new flag like
SPI_NOR_4BAM_DEFAULTand check
the flag in BFPT parse. Once I send another series, please review.Quoted 3 lines
We need to differentiate between the mode the flash currently is using (
nor->addr_nbytes) and the mode parsed by SFDP (params->addr_nbytes).Quoted 8 lines
The flash's address mode affects the address length of Non-4B opcodes, including read/write any register ops used in SMPT parse and Infineon (spansion) specific hooks.
The 4B opcodes always take address length of 4 regardless of flash's address mode. In these Infineon chips, 4B opcodes for read/program/ erase are available and 4BAIT advertises them. We don't have to enter 4 byte address mode for read/program/erase.
btw. this is a pity. you are using the stateless 4b opcodes but then you don't provide stateless opcodes for the read any register op :/
Quoted 2 lines
So, I think we need to differentiate between address length for read/program/erase and flash's default address mode.
Or we keep them in sync. E.g. switch to 4bytes mode if we are using the 4 byte. Granted, that sounds like a hack :)
Quoted 2 lines
Obviously we are using
nor->addr_nbytesas address length for read/ program/erase and should keep this usage.Yes, I wasn't aware that we actually two different runtime parameters:
- the read/program/erase address width, also used with the 4b opcodes
- internal mode 3b/4b. Up until now, this wasn't an issue because either the mode was switched or the 4b opcodes were used. So this was mutually exclusive. Now we have flashes which uses 4b opcodes _and_ we need the state of the internal mode.I can't think of a good solution for now. Need to think more about this, but I'm pretty busy at the moment. What I think is clear is that we need two different modes here in the
spi_norstruct.nor->addr_nbytesfor the read/program/erase opcodes andnor->address_modeor similar which tracks the SPI flash's internal address mode.Quoted 9 lines
Quoted 5 lines
Hi, Takahiro,
Can we determine the flash's internal address mode by querying the flash at run-time? Is this possible on Semper flashes?
CFR2V[7] has current address mode, but to read that, we need to issue Read Any Register which address length relies on current address mode. Chicken-and-egg...
Quoted 6 lines
I see. What happens if we issue the Read Any Register command with the wrong address internal mode? Will I read just
0xff? For example try reading CFR2V[7] usingaddr_nbytesof value 3, and if it fails, to read it again but this time usingaddr_nbytesof value 4.Quoted 6 lines
It's undetermined. In case we issue Read Any Register with 3B address, the host controller outputs 4 bytes (opcode + address) then inputs 1 byte. If the device is in 4B address mode at this time, the host controller inputs the 1 byte while device is still waits for LSB of address so IO is not driven by device.
So if the IO lines are floating, we'll "read" whatever is indicated by the IOs at that specific moment of time, right?
Quoted 8 lines
Quoted 6 lines
Yes, right.
Quoted 3 lines
If so, we're forced to statically specify the default internal address mode.
Yes.
OK, let me scratch something.
Would you please send me the datasheet for Semper flashes?
I noticed that the addr mode is controlled via a volatile conf register in your case, but there are flashes like w25q256jv that control the addr mode via a non-volatile register, so only a default value will not empower flashes with NV register conf to actually toggle that bit. We may introduce a dt prop for the NV case when needed, the disadvantage being that the generic jedec,spi-nor will not be so generic, as it will have a fixed default NV addr mode specified in dt.
Signature · 5 lines
Cheers, ta ______________________________________________________ Linux MTD discussion mailing list http://lists.infradead.org/mailman/listinfo/linux-mtd/
Re: [PATCH v15 6/8] mtd: spi-nor: Retain nor->addr_width at 4BAIT parse
Quoted 151 lines · On 7/22/22 10:38, Tudor Ambarus - M18064 wrote:
Quoted 141 lines · On 7/22/22 09:08, [email protected] wrote:
EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
Quoted 138 lines · Takahiro Kuwano
EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
Quoted 135 lines · On 7/22/2022 2:06 PM, [email protected] wrote:
Quoted 124 lines · Takahiro Kuwano
EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
Quoted 4 lines · On 7/22/2022 1:20 PM, [email protected] wrote:
On 7/22/22 07:00, Takahiro Kuwano wrote:
Good morning, Takahiro!
Good morning, Tudor!
Quoted 109 lines
Quoted 99 lines
EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
Quoted 96 lines · On 7/22/2022 1:06 AM, [email protected] wrote:
Quoted 94 lines · Michael Walle
EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
Am 2022-05-14 05:51, schrieb Takahiro Kuwano:
Quoted 53 lines · Michael Walle
Quoted 2 lines
[btw the subject still has the old name of the
addr_width]Yes, it must be fixed in next rev.
Quoted 31 lines
Am 2022-05-13 03:26, schrieb Takahiro Kuwano:
Quoted 22 lines · Michael Walle
Quoted 21 lines
Am 2022-05-10 00:10, schrieb [email protected]:
From: Takahiro Kuwano <[email protected]>In 4BAIT parse, keep nor->params->addr_width because it may be used
as
current address mode in SMPT parse later on.Mh I'm not sure this is needed at all.
SFDP spec says
Variable address length (the current setting of the address
length mode defines the address length)and
When the length is defined as variable, the software or hardware
controlling the memory is aware of the address length mode last
set in the memory device and this same length of address.We don't set any address mode until all the SFDP parsing is
over. Therefore we should always be in 3 byte mode, no?Quoted 7 lines
Actually there are some devices that have variable address length but 4 byte mode by default (I will work on those devices after this series
is settled). To support such case, I prefer to useparams->addr_nbytes
as current address mode so that I can fix it inpost_bfpt_fixup()hook.Quoted 1 line
Are there public datasheets available? So these devices have a 3 byte
I will send datasheets to you in another email. At this point, only summary datasheet is available in website.
Quoted 1 line
and a 4 byte mode, but after reset, they are in the 4 byte mode? Looks
Yes.
Quoted 3 lines
like it should be fixed in a different way. I'm not sure the "current mode" handling is correct.
Yes, we may want to introduce a new flag like
SPI_NOR_4BAM_DEFAULTand check
the flag in BFPT parse. Once I send another series, please review.Quoted 3 lines
We need to differentiate between the mode the flash currently is using (
nor->addr_nbytes) and the mode parsed by SFDP (params->addr_nbytes).Quoted 8 lines
The flash's address mode affects the address length of Non-4B opcodes, including read/write any register ops used in SMPT parse and Infineon (spansion) specific hooks.
The 4B opcodes always take address length of 4 regardless of flash's address mode. In these Infineon chips, 4B opcodes for read/program/ erase are available and 4BAIT advertises them. We don't have to enter 4 byte address mode for read/program/erase.
btw. this is a pity. you are using the stateless 4b opcodes but then you don't provide stateless opcodes for the read any register op :/
Quoted 2 lines
So, I think we need to differentiate between address length for read/program/erase and flash's default address mode.
Or we keep them in sync. E.g. switch to 4bytes mode if we are using the 4 byte. Granted, that sounds like a hack :)
Quoted 2 lines
Obviously we are using
nor->addr_nbytesas address length for read/ program/erase and should keep this usage.Yes, I wasn't aware that we actually two different runtime parameters:
- the read/program/erase address width, also used with the 4b opcodes
- internal mode 3b/4b. Up until now, this wasn't an issue because either the mode was switched or the 4b opcodes were used. So this was mutually exclusive. Now we have flashes which uses 4b opcodes _and_ we need the state of the internal mode.I can't think of a good solution for now. Need to think more about this, but I'm pretty busy at the moment. What I think is clear is that we need two different modes here in the
spi_norstruct.nor->addr_nbytesfor the read/program/erase opcodes andnor->address_modeor similar which tracks the SPI flash's internal address mode.Quoted 9 lines
Quoted 5 lines
Hi, Takahiro,
Can we determine the flash's internal address mode by querying the flash at run-time? Is this possible on Semper flashes?
CFR2V[7] has current address mode, but to read that, we need to issue Read Any Register which address length relies on current address mode. Chicken-and-egg...
Quoted 6 lines
I see. What happens if we issue the Read Any Register command with the wrong address internal mode? Will I read just
0xff? For example try reading CFR2V[7] usingaddr_nbytesof value 3, and if it fails, to read it again but this time usingaddr_nbytesof value 4.Quoted 6 lines
It's undetermined. In case we issue Read Any Register with 3B address, the host controller outputs 4 bytes (opcode + address) then inputs 1 byte. If the device is in 4B address mode at this time, the host controller inputs the 1 byte while device is still waits for LSB of address so IO is not driven by device.
So if the IO lines are floating, we'll "read" whatever is indicated by the IOs at that specific moment of time, right?
Quoted 8 lines
Quoted 6 lines
Yes, right.
Quoted 3 lines
If so, we're forced to statically specify the default internal address mode.
Yes.
OK, let me scratch something.
Quoted 9 lines
Would you please send me the datasheet for Semper flashes?
I noticed that the addr mode is controlled via a volatile conf register in your case, but there are flashes like w25q256jv that control the addr mode via a non-volatile register, so only a default value will not empower flashes with NV register conf to actually toggle that bit. We may introduce a dt prop for the NV case when needed, the disadvantage being that the generic jedec,spi-nor will not be so generic, as it will have a fixed default NV addr mode specified in dt.
Oh, but winbond uses a dedicated RDSR3 opcode and doesn't need addr_nbytes, so it's safe. It looks like we can use an addr_mode_nbytes after all.
Signature · 5 lines
Cheers, ta ______________________________________________________ Linux MTD discussion mailing list http://lists.infradead.org/mailman/listinfo/linux-mtd/
Re: [PATCH v15 6/8] mtd: spi-nor: Retain nor->addr_width at 4BAIT parse
In reply to Takahiro KuwanoQuoted 36 lines · Takahiro Kuwano
EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
Quoted 2 lines · Michael Walle
[btw the subject still has the old name of the
addr_width]Yes, it must be fixed in next rev.
Quoted 18 lines
Am 2022-05-13 03:26, schrieb Takahiro Kuwano:
Quoted 17 lines · Michael Walle
Quoted 16 lines
Am 2022-05-10 00:10, schrieb [email protected]:
Quoted 4 lines
From: Takahiro Kuwano <[email protected]>
In 4BAIT parse, keep
nor->params->addr_widthbecause it may be used as current address mode in SMPT parse later on.Mh I'm not sure this is needed at all.
SFDP spec says
Variable address length (the current setting of the address length mode defines the address length)and
When the length is defined as variable, the software or hardware controlling the memory is aware of the address length mode last set in the memory device and this same length of address.Quoted 8 lines
Quoted 7 lines
Quoted 3 lines
We don't set any address mode until all the SFDP parsing is over. Therefore we should always be in 3 byte mode, no?
Actually there are some devices that have variable address length but 4 byte mode by default (I will work on those devices after this series is settled). To support such case, I prefer to use
params->addr_nbytesas current address mode so that I can fix it inpost_bfpt_fixup()hook.Are there public datasheets available? So these devices have a 3 byte
I will send datasheets to you in another email. At this point, only summary datasheet is available in website.
Quoted 9 lines
Quoted 1 line
and a 4 byte mode, but after reset, they are in the 4 byte mode? Looks
Yes.
Quoted 3 lines
like it should be fixed in a different way. I'm not sure the "current mode" handling is correct.
Yes, we may want to introduce a new flag like
SPI_NOR_4BAM_DEFAULTand check the flag in BFPT parse. Once I send another series, please review.
Sounds good on a first look. We can consider nor->addr_nbytes of value 3 as default and change it to 4 when such a flag is set. But you don't need such flag in this particular case, don't you? Also, can the default number of addr bytes be retrieved from SFDP? Anyway, let this for later and respin the series, please.
Cheers,
ta
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
PATCH v15 7/8 mtd: spi-nor: spansion: Add local function to discover page size
In reply to [email protected]From: Takahiro Kuwano <[email protected]>
The page size check in s28hs512t fixup can be used for s25hs/hl-t as well. Move that to a newly created local function. Please note that the hardcoded value 3 for the number of address bytes was replaced by nor->params->addr_nbytes.
--- drivers/mtd/spi-nor/spansion.c | 54 ++++++++++++++++++++-------------- 1 file changed, 32 insertions(+), 22 deletions(-)
drivers/mtd/spi-nor/spansion.c +32 -22
@@ -113,6 +113,37 @@ static int cypress_nor_octal_dtr_dis(struct spi_nor *nor)return 0 ; } +/** +* cypress_nor_set_page_size() - Set page size which corresponds to the flash +* configuration. +* @nor: pointer to a 'struct spi_nor' +* +* The BFPT table advertises a 512B or 256B page size depending on part but the +* page size is actually configurable (with the default being 256B). Read from +* CFR3V[4] and set the correct size. +* +* Return: 0 on success, -errno otherwise. +*/ +static int cypress_nor_set_page_size (struct spi_nor *nor) +{ +struct spi_mem_op op = +CYPRESS_NOR_RD_ANY_REG_OP (nor->params->addr_nbytes, +SPINOR_REG_CYPRESS_CFR3V , + nor->bouncebuf); +int ret; + + ret =spi_nor_read_any_reg (nor, &op, nor->reg_proto); +if (ret) +return ret; + +if (nor->bouncebuf[0 ] &SPINOR_REG_CYPRESS_CFR3V_PGSZ ) + nor->params->page_size =512 ; +else + nor->params->page_size =256 ; + +return 0 ; +} +/** * cypress_nor_octal_dtr_enable() - Enable octal DTR on Cypress flashes. * @nor: pointer to a 'struct spi_nor'
@@ -167,28 +198,7 @@ static int s28hs512t_post_bfpt_fixup(struct spi_nor *nor,const struct sfdp_parameter_header *bfpt_header, const struct sfdp_bfpt *bfpt) { -/* -* The BFPT table advertises a 512B page size but the page size is -* actually configurable (with the default being 256B). Read from -* CFR3V[4] and set the correct size. -*/ -struct spi_mem_op op = -CYPRESS_NOR_RD_ANY_REG_OP (3 ,SPINOR_REG_CYPRESS_CFR3V , - nor->bouncebuf); -int ret; - -spi_nor_spimem_setup_op (nor, &op, nor->reg_proto); - - ret =spi_mem_exec_op (nor->spimem, &op); -if (ret) -return ret; - -if (nor->bouncebuf[0 ] &SPINOR_REG_CYPRESS_CFR3V_PGSZ ) - nor->params->page_size =512 ; -else - nor->params->page_size =256 ; - -return 0 ; + return cypress_nor_set_page_size(nor); } static const struct spi_nor_fixups s28hs512t_fixups = {
Signature · 6 lines
2.25.1 ______________________________________________________ Linux MTD discussion mailing list http://lists.infradead.org/mailman/listinfo/linux-mtd/
PATCH v15 8/8 mtd: spi-nor: spansion: Add s25hl-t/s25hs-t IDs and fixups
In reply to [email protected]From: Takahiro Kuwano <[email protected]>
The S25HL-T/S25HS-T family is the Infineon SEMPER Flash with Quad SPI.
These Infineon chips support volatile version of configuration registers and it is recommended to update volatile registers in the field application due to a risk of the non-volatile registers corruption by power interrupt. Add support for volatile QE bit.
For the single-die package parts (512Mb and 1Gb), only bottom 4KB and uniform sector sizes are supported. This is due to missing or incorrect entries in SMPT. Fixup for other sector sizes configurations will be followed up as needed.
Tested on Xilinx Zynq-7000 FPGA board.
--- drivers/mtd/spi-nor/spansion.c | 129 +++++++++++++++++++++++++++++++++ 1 file changed, 129 insertions(+)
drivers/mtd/spi-nor/spansion.c +129 -0
@@ -14,6 +14,8 @@#define SPINOR_OP_CLSR 0x30/* Clear status register 1 */ #define SPINOR_OP_RD_ANY_REG 0x65/* Read any register */ #define SPINOR_OP_WR_ANY_REG 0x71/* Write any register */ +#define SPINOR_REG_CYPRESS_CFR1V 0x00800002 +#define SPINOR_REG_CYPRESS_CFR1V_QUAD_EN BIT(1)/* Quad Enable */ #define SPINOR_REG_CYPRESS_CFR2V 0x00800003#define SPINOR_REG_CYPRESS_CFR2V_MEMLAT_11_24 0xb#define SPINOR_REG_CYPRESS_CFR3V 0x00800004
@@ -113,6 +115,67 @@ static int cypress_nor_octal_dtr_dis(struct spi_nor *nor)return 0 ; } +/** +* cypress_nor_quad_enable_volatile() - enable Quad I/O mode in volatile +* register. +* @nor: pointer to a 'struct spi_nor' +* +* It is recommended to update volatile registers in the field application due +* to a risk of the non-volatile registers corruption by power interrupt. This +* function sets Quad Enable bit in CFR1 volatile. If users set the Quad Enable +* bit in the CFR1 non-volatile in advance (typically by a Flash programmer +* before mounting Flash on PCB), the Quad Enable bit in the CFR1 volatile is +* also set during Flash power-up. +* +* Return: 0 on success, -errno otherwise. +*/ +static int cypress_nor_quad_enable_volatile (struct spi_nor *nor) +{ +struct spi_mem_op op; +u8 cfr1v_written; +int ret; + + op = (struct spi_mem_op ) +CYPRESS_NOR_RD_ANY_REG_OP (nor->params->addr_nbytes, +SPINOR_REG_CYPRESS_CFR1V , + nor->bouncebuf); + + ret =spi_nor_read_any_reg (nor, &op, nor->reg_proto); +if (ret) +return ret; + +if (nor->bouncebuf[0 ] &SPINOR_REG_CYPRESS_CFR1V_QUAD_EN ) +return 0 ; + +/* Update the Quad Enable bit. */ + nor->bouncebuf[0 ] |=SPINOR_REG_CYPRESS_CFR1V_QUAD_EN ; + op = (struct spi_mem_op ) +CYPRESS_NOR_WR_ANY_REG_OP (nor->params->addr_nbytes, +SPINOR_REG_CYPRESS_CFR1V ,1 , + nor->bouncebuf); + ret =spi_nor_write_any_volatile_reg (nor, &op, nor->reg_proto); +if (ret) +return ret; + + cfr1v_written = nor->bouncebuf[0 ]; + +/* Read back and check it. */ + op = (struct spi_mem_op ) +CYPRESS_NOR_RD_ANY_REG_OP (nor->params->addr_nbytes, +SPINOR_REG_CYPRESS_CFR1V , + nor->bouncebuf); + ret =spi_nor_read_any_reg (nor, &op, nor->reg_proto); +if (ret) +return ret; + +if (nor->bouncebuf[0 ] != cfr1v_written) { +dev_err (nor->dev,"CFR1: Read back test failed\n" ); +return -EIO ; + } + +return 0 ; +} +/** * cypress_nor_set_page_size() - Set page size which corresponds to the flash * configuration.
@@ -144,6 +207,56 @@ static int cypress_nor_set_page_size(struct spi_nor *nor)return 0 ; } +static int +s25hx_t_post_bfpt_fixup (struct spi_nor *nor, +const struct sfdp_parameter_header *bfpt_header, +const struct sfdp_bfpt *bfpt) +{ +/* Replace Quad Enable with volatile version */ + nor->params->quad_enable = cypress_nor_quad_enable_volatile; + +return cypress_nor_set_page_size (nor); +} + +static void s25hx_t_post_sfdp_fixup (struct spi_nor *nor) +{ +struct spi_nor_erase_type *erase_type = + nor->params->erase_map.erase_type; +int i; + +/* +* In some parts, 3byte erase opcodes are advertised by 4BAIT. +* Convert them to 4byte erase opcodes. +*/ +for (i =0 ; i <SNOR_ERASE_TYPE_MAX ; i++) { +switch (erase_type[i].opcode) { +case SPINOR_OP_SE : + erase_type[i].opcode =SPINOR_OP_SE_4B ; +break ; +case SPINOR_OP_BE_4K : + erase_type[i].opcode =SPINOR_OP_BE_4K_4B ; +break ; +default : +break ; + } + } +} + +static void s25hx_t_late_init (struct spi_nor *nor) +{ +/* Fast Read 4B requires mode cycles */ + nor->params->reads[SNOR_CMD_READ_FAST ].num_mode_clocks =8 ; + +/* The writesize should be ECC data unit size */ + nor->params->writesize =16 ; +} + +static struct spi_nor_fixups s25hx_t_fixups = { + .post_bfpt = s25hx_t_post_bfpt_fixup, + .post_sfdp = s25hx_t_post_sfdp_fixup, + .late_init = s25hx_t_late_init, +}; +/** * cypress_nor_octal_dtr_enable() - Enable octal DTR on Cypress flashes. * @nor: pointer to a 'struct spi_nor'
@@ -320,6 +433,22 @@ static const struct flash_info spansion_nor_parts[] = { { "s25fl256l", INFO(0x016019, 0, 64 * 1024, 512) NO_SFDP_FLAGS(SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) FIXUP_FLAGS(SPI_NOR_4B_OPCODES) }, + { "s25hl512t", INFO6(0x342a1a, 0x0f0390, 256 * 1024, 256) + PARSE_SFDP + MFR_FLAGS(USE_CLSR) + .fixups = &s25hx_t_fixups }, + { "s25hl01gt", INFO6(0x342a1b, 0x0f0390, 256 * 1024, 512) + PARSE_SFDP + MFR_FLAGS(USE_CLSR) + .fixups = &s25hx_t_fixups }, + { "s25hs512t", INFO6(0x342b1a, 0x0f0390, 256 * 1024, 256) + PARSE_SFDP + MFR_FLAGS(USE_CLSR) + .fixups = &s25hx_t_fixups }, + { "s25hs01gt", INFO6(0x342b1b, 0x0f0390, 256 * 1024, 512) + PARSE_SFDP + MFR_FLAGS(USE_CLSR) + .fixups = &s25hx_t_fixups }, { "cy15x104q", INFO6(0x042cc2, 0x7f7f7f, 512 * 1024, 1) FLAGS(SPI_NOR_NO_ERASE) }, { "s28hs512t", INFO(0x345b1a, 0, 256 * 1024, 256)
Signature · 6 lines
2.25.1 ______________________________________________________ Linux MTD discussion mailing list http://lists.infradead.org/mailman/listinfo/linux-mtd/